600_2001

600_2001
BRONZE CLOSE COUPLED
CENTRIFUGAL PUMP
OBERDORFER PUMPS
MODEL
600
A Subsidiary of Thomas Industries Inc.
CAPACITY Water at 60o F
PIPE SIZE: INLET 3/4”, OUTLET 1/2”
FEATURES
n All Bronze Pump Castings
n Stainless Steel Motor Shaft
n Mechanical Seal
n Extremely Quiet
n Will handle difficult solvents with proper seals Viton(R)* (S10), or Teflon(R)* (S11)
n Long Life
n Do Not Require Relief Valves
n Will Handle Contaminated Liquids
LIQUIDS
The special pump alloys used provide corrosion resistance to many liquids including water, water solutions, and a
wide range of commercial chemicals. Questions as to the
chemical compatibility of special liquids should be referred to
the factory.
Viscous liquids with a maximum viscosity of 2000
Saybolt Seconds Universal can be pumped. However, when
pumping viscous liquids as compared with water, a reduction
inflow and pressure occurs and the required horsepower
rate increases.
Liquids heavier than water require additional horsepower in direct proportion to the increase in specific gravity.
Liquids contaminated with small solids or abrasives can be
handled, but a reduction in mechanical seal life must be
expected.
CHARACTERISTICS
This close coupled pump uses a standard NEMA CFlange Jet Pump Motor with weld-on base and threaded
shaft end to accept the pump impeller. Single phase motors
are non-reversible and are wired for the proper pump rotation which is counter-clockwise looking at the inlet end of the
pump. Three phase motors must be checked out for proper rotation when pump is installed. Interchanging of any 2 wires in a 3phase system will reverse motor rotation.
The pump uses a mechanical type shaft seal with a Buna
rubber element. It is suitable for water, oils, and some mild solvents. It is limited to 212o F and 75 P.S.I. Viton (R)* seals and
Teflon(R)* seals are available for severe solvents and difficult
chemicals.
These centrifugal pumps are not self-priming. They must be
installed below the liquid level so that the liquid flows to the pump
by gravity (flooded suction). However, if a foot valve is used at the
beginning of the suction line and all air is bled from the pump by
manual priming, the pump will lift on the suction side up to 15 feet.
Such a system relies entirely on a non-leaking foot valve for starting capability.
The flow of a centrifugal pump can be conveniently controlled by a throttling valve in the discharge line without the need
for a relief valve. In centrifugal pumps, the horsepower demand
will decrease as the pressure increases. Maximum horsepower
occurs with a wide open discharge.
* Viton(R) is a registered trademark of DuPont Dow Elastomers. Viton(R) or equivalent FKM will be used.
Teflon(R) is a registered trademark of DuPont. Teflon(R) or equivalent will be used.
www.oberdorfer-pumps.com
PHONE 800-448-1668; (315) 437-0361
FAX (315) 463-9561
BRONZE CLOSE COUPLED
CENTRIFUGAL PUMP
OBERDORFER PUMPS
MODEL
600
A Subsidiary of Thomas Industries Inc.
EXPLODED VIEW AND PARTS LIST
Pump No.
1
2
Screw
Cover
31
41
Gasket Impeller
51
6
7
8
9
10
Seal
Plug
Body
Screw
Screw
Adapter
Assy.
8 Reqd 1 Reqd
600
5385
5168
1 Reqd
1 Reqd
5328
5219
600P
5385
5168
5328
600S-10
5385
5168
5328
600S-11
5385
5168
6175
600PS-10 5385
5168
5328
600PS-11 5385
5168
6175
1
Repair Kit contains items 3, 4, 5, & 11.
PUMP AND MOTOR
COMBINATIONS
Note: These are the most frequently
used pump and motor combinations. If
you have other needs, our sales reps
can recommend a pump and motor for
your application.
7201
6033
6033
7432
7432
Set
Screw
1 Reqd 2 Reqd 1 Reqd 1 Reqd
32154
111,2
6052
7515
5595
4 Reqd
1 Reqd
5411
7611
1 Reqd
---
32154
5395
7515
5595
5411
7611
9849
32210
6052
7515
5595
5411
7611
--32211
6052
6173
5595
5411
7611
--32210
6052
7515
5595
5411
7611
9849
32211
6052
6173
5595
5411
7611
9849
2
Item 11 is located in the impeller, not shown in exploded view.
Pump No.
600, 600S-10, 600S-11
Motor
F13
Repair
Kit1
10696
Single Phase
10858
10814
10768
12175
11747
Three Phase
Single Phase
Single Phase
Three Phase
Three Phase
Electric Motor Specs
1/3 HP, 3450 RPM, 115v, Single, ODP
Part #
5859
600
F19
1/3 HP, 3450 RPM, 115/230v, Single, ODP
7957
600
F20
1/3 HP, 3450 RPM, 115/230v, Single, TEFC
7986
600
F21
1/3 HP, 3450 RPM, 115/230v, Single, XP
8214
600
F22
1/3 HP, 2850 RPM, 115/230v, Single ODP
9758
600, 600S-10, 600S-11
J19
1/2 HP, 3450 RPM, 115/230v, Single, ODP
5860
600, 600S-10, 600S-11
J20
1/2 HP, 3450 RPM, 115/230v, Single, TEFC
7976
600P, 600P-S10, 600PS-11
F57
1/3 HP, 3450 RPM, 220/440v, Three, ODP
6996
600P
M57
3/4 HP, 3450 RPM, 220/440v, Three, ODP
6999
600P, 600P-S10, 600PS-11
M58
3/4 HP, 3450 RPM, 220/440v, Three, TEFC
7967
600P-S10, 600PS-11
F58
1/3 HP, 3450 RPM, 220/440v, Three, TEFC
7987
600P, 600P-S10, 600PS-11
J58
1/2 HP, 3450 RPM, 220/440v, Three, TEFC
9214
DIMENSIONS
(A typical 600-F13
or 600P-F57 shown.)
3/01
www.oberdorfer-pumps.com
Specifications are subject to change without notice.
PHONE 800-448-1668; (315) 437-0361
FAX (315) 463-9561
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement