Methven Maku Satinjet Slide Rail Shower Shower Installation Guide

Below you will find brief information for Shower Maku Satinjet Slide Rail Shower. This guide provides instructions for installing the shower, including mounting the rail, aligning the internal mounting brackets, securing the wall boss housings, and attaching the end cap. It also covers the adjustment of sliders and the tightening of tensioning screws for a secure and stable installation.

PDF Download

Document

CLEANING

Water contains lime which remains on the surface after the water has evaporated. These lime deposits can be prevented from forming by wiping immediately after use.

To clean the chrome-plated surface use a soft cloth, soap and warm water. Never use cleaning agents that contain a corrosive acid or a scouring additive.

Clean filter washer periodicallly

MAKU SATINJET SLIDE RAIL SHOWER

INSTALLATION GUIDE

TECHNICAL SPECIFICATIONS

Operating Pressure:

Min 35 kPa, Max 500 kPa.

Recommended installation of a pressure limiting valve if supply exceeds 500kPa.

Operating Temperature:

Max 70°C.

NB: New Zealand Building Code Clause G12 -

Water Supplies specifies all outlets used primarily for personal hygiene shall deliver water at a safe temperature.

Inlet Connections: All ½" BSP.

Do not use any shap objects to clean nozzles

NOTES:

1) Low and unequal systems:

Removal of the flow restrictor with pliers may be necessary to optimise flow performance in low or unequal pressure systems only. Flow restrictor is lodged firmly in the end of the handset.

Methven warrants this product against manufacturing defects and that it is suitable for use under the operating conditions specified in this instruction sheet.

For your warranty please refer to www.methven.com or call Customer Service

New Zealand

0800 804 222

Australia

1300 638 483

0800 195 1602

436932 Issue A

Maku Handset

Slider

Hose

Elbow

grub screw topside

Wall Boss Housing

Internal Mounting Bracket

Rail

Screw

Grub Srew

NOTE: ENSURE

PROTECTION

PADS ARE USED

BETWEEN WALL

BOSSES AND TILES grub screw underside

Secure the wall boss housings in desired position with 4 screws.

Check the mounts are vertical.

Ensure the grub screws are located as shown.

Floor

Match the mountings up to the wall bosses and push into place.

Slide the rail up and down if required to centralise the rail on the brackets

Once satisfied that the rail is centralised remove the rail and tighten the tensioning screws until they lock.

Relocate the rail onto wall bosses and tighten grub screws top and bottom.

Orientate rail so that pre-fitted endcap is at bottom of rail

Fitted endcap

Fit end cap to top of rail. Ensure drainage hole is at back

Fit the internal mounting brackets by locating in slot and rotating 90° as shown.

Once located tighten the screws finger-tight.

NOTE: TO LOOSEN SLIDERS

GRIP ON RAIL ROTATE SIDE

PIECE ANTI-CLOCKWISE.

ROTATE CLOCKWISE TO

TIGHTEN

Flat Washer

Swivelling

Cone

Filter Washer

Non-Swivelling Cone

Hello! I am an AI chatbot specifically trained to assist you with the Methven Maku Satinjet Slide Rail Shower Shower Installation Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Slide Rail Installation
Wall Mounting Brackets
Adjustable Slider
Chrome-plated Finish
Flow Restrictor
Pressure Limiting Valve
Safe Temperature
Easy Cleaning

Frequently asked questions

Follow the instructions in the installation guide, which includes steps for mounting the rail, securing the wall boss housings, and attaching the end cap.

The recommended operating pressure is between 35 kPa and 500 kPa. A pressure limiting valve is recommended if the supply exceeds 500 kPa.

The maximum operating temperature is 70°C. New Zealand Building Code Clause G12 Water Supplies specifies all outlets used primarily for personal hygiene shall deliver water at a safe temperature.