MGE UPS Systems | 3200RT | User manual | MGE UPS Systems 3200RT User manual

www.mgeups.com
Network
Management Card (66102)
User Manual
Minislot 2006 Edition
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
P R O V I D E R
34003991EN/GA
Page 1/63
Contents
1
MGE NETWORK SOLUTION ___________________________________________________________________________________ 4
1.1
1.1.1
Connecting the UPS to the Ethernet network_______________________________________________________________ 4
1.1.2
Protection of the computers / servers_____________________________________________________________________ 5
1.1.3
Supervision of the UPSs over the network _________________________________________________________________ 5
1.1.4
1.2
Compatibility with UPSs _______________________________________________________________________________ 6
1.2.2
Direct sending of E-mail _______________________________________________________________________________ 7
1.2.3
Sending text messages (SMS) __________________________________________________________________________ 7
1.2.4
Compatibility with the Network Managment Systems (NMS) – Trap sending ______________________________________ 7
1.2.5
1.3.1
3
4
Connection _________________________________________________________________________________________ 5
PRESENTATION OF THE NETWORK MANAGEMENT CARD (NMC) _______________________________________________________ 6
1.2.1
1.3
2
GENERAL PRESENTATION ___________________________________________________________________________________ 4
Environment Sensor (option) ___________________________________________________________________________ 7
TECHNICAL DATA _________________________________________________________________________________________ 7
Hardware characteristics ______________________________________________________________________________ 7
1.3.2
EMC Compatibility ___________________________________________________________________________________ 7
1.3.3
Configuration _______________________________________________________________________________________ 8
1.3.4
Administration_______________________________________________________________________________________ 8
1.3.5
Network ___________________________________________________________________________________________ 8
1.3.6
Environment sensor __________________________________________________________________________________ 8
1.3.7
MIB (Management Information Base) ____________________________________________________________________ 9
1.3.8
Default parameters ___________________________________________________________________________________ 9
INSTALLATION _____________________________________________________________________________________________ 10
2.1.1
Unpacking and check on contents ______________________________________________________________________ 10
2.1.2
Indications ________________________________________________________________________________________ 10
2.1.3
Installation in the UPS _______________________________________________________________________________ 11
2.1.4
Sensor installation (option) ____________________________________________________________________________ 11
CONFIGURATION ___________________________________________________________________________________________ 12
3.1.1
Configure IP parameters _____________________________________________________________________________ 12
3.1.2
Test after configuration_______________________________________________________________________________ 13
SUPERVISION AND ADMINISTRATION BY BROWSER ____________________________________________________________ 14
4.1.1
4.2
Optimising the performance of your browser ______________________________________________________________ 14
UPS __________________________________________________________________________________________________ 15
4.2.1
UPS properties page ________________________________________________________________________________ 15
4.2.2
On-line help _______________________________________________________________________________________ 17
4.2.3
UPS control _______________________________________________________________________________________ 18
4.2.4
UPS weekly schedule programming ____________________________________________________________________ 20
4.2.5
Shutdown parameters _______________________________________________________________________________ 21
4.2.6
Viewing the alarms __________________________________________________________________________________ 23
4.2.7
Measurements _____________________________________________________________________________________ 24
4.2.8
Event log__________________________________________________________________________________________ 25
4.2.9
4.3
T H E
System log ________________________________________________________________________________________ 25
NOTIFICATION ___________________________________________________________________________________________ 26
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-2-
4.3.1
Email Notification ___________________________________________________________________________________ 26
4.3.2
E-mail Message Settings _____________________________________________________________________________ 28
4.4
Network settings ____________________________________________________________________________________ 31
4.4.2
System ___________________________________________________________________________________________ 33
4.4.3
Notified Applications _________________________________________________________________________________ 34
4.4.4
Central shutdown configuration ________________________________________________________________________ 36
4.4.5
Access control _____________________________________________________________________________________ 37
4.4.6
Date and time ______________________________________________________________________________________ 39
4.4.7
4.5
5
Characteristics _____________________________________________________________________________________ 41
4.5.2
Environment Status _________________________________________________________________________________ 42
4.5.3
Environment Settings ________________________________________________________________________________ 43
4.5.4
Log ______________________________________________________________________________________________ 45
SERVER PROTECTION ______________________________________________________________________________________ 46
Shutdown criteria managed by the Network Management Card _______________________________________________ 46
5.1.2
Controlled outlets ___________________________________________________________________________________ 47
5.1.3
Protection of a server connected to a controlled outlet ______________________________________________________ 48
THE DIFFERENT SERVER AND UPS SHUTDOWN SEQUENCES _________________________________________________________ 49
5.2.1
Extended power outage, shutdown initiated by the Shutdown Timer (Shutdown after) ______________________________ 49
5.2.2
Extended power outage, shutdown initiated by the "Low battery power" message _________________________________ 49
5.2.3
Case of power restoration before the end of the "shutdown duration" counter ____________________________________ 50
CONFIGURATION VIA RS232 _________________________________________________________________________________ 51
6.1
CHOICE 1: RESTART / RESET _______________________________________________________________________________ 51
6.2
CHOICE 2: NETWORK CONFIGURATION ________________________________________________________________________ 51
6.2.1
Choice 1: Read Network settings _______________________________________________________________________ 52
6.2.2
Choice 2: Modify Network settings ______________________________________________________________________ 52
6.3
CHOICE 3: LOST PASSWORD / SET LOGIN PASSWORD TO DEFAULT ___________________________________________________ 52
6.4
CHOICE 4: RETURN TO DEFAULT CONFIGURATION ________________________________________________________________ 53
APPENDICES ______________________________________________________________________________________________ 54
7.1
TABLES OF ALARMS AND EVENTS_____________________________________________________________________________ 54
7.1.1
Table of alarms_____________________________________________________________________________________ 54
7.1.2
Table of UPS events_________________________________________________________________________________ 55
7.1.3
Table of system alarms ______________________________________________________________________________ 56
7.2
8
SET-UP OF THE SHUTDOWN PARAMETERS ______________________________________________________________________ 46
5.1.1
5.2
7
Firmware upload____________________________________________________________________________________ 40
ENVIRONMENT SENSOR (OPTION) ____________________________________________________________________________ 41
4.5.1
5.1
6
CONFIGURATION _________________________________________________________________________________________ 30
4.4.1
SNMP OBJECTS _________________________________________________________________________________________ 57
7.2.1
MGE MIB _________________________________________________________________________________________ 57
7.2.2
Table des TRAPS : (1.3.6.1.4.1.705.1.11) ________________________________________________________________ 60
GLOSSARY ________________________________________________________________________________________________ 61
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-3-
1 MGE Network Solution
1.1
General Presentation
MGE Network Solution:
Z
provides information on events concerning the supply of power to the computers connected to your computer network,
Z
carries out automatic shutdown of computer systems,
Z
monitors and controls all the UPSs connected to the network.
As illustrated in the picture below, MGE Network Solution provides these 3 main functions:
Z
supervision of the UPSs over the Network,
Z
protection of the computers,
Z
connexion of the UPS to the Network.
1.1.1 Connecting the UPS to the Ethernet network
This function can be performed either through network Cards inserted in the UPS (Network Management Card) or through a software "agent"
running on a nearby PC that is called the Network Management Proxy.
The Network Management Card or Proxy:
manages communication with the UPS (as well as local protection of the machine on which Proxy is installed),
periodically accesses the information concerning the UPS,
makes this information available to the connected applications (Network Shutdown Modules, Web Browser, Network Management Systems,
Enterprise Power Manager),
sends notifications on certain events
Operation may be in standard secure mode (the default mode) or in SSL secure mode (Secure Socket Layer SSL).
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-4-
1.1.2 Protection of the computers / servers
This function is performed by the Network Shutdown Module installed on each of the servers to be protected.
Note that the Shutdown Module is available on several Operating Systems.
The Network Shutdown Module:
continuously waits for information from the Network Management Card / Proxy connected to the MGE UPS.
warns administrators and users if AC power fails and proceeds with graceful system shutdown before the end of battery backup power is
reached.
1.1.3 Supervision of the UPSs over the network
Depending on your needs, you can either use:
your Internet browser to monitor each UPS, as Management Proxy and Management Card include a Web server.
your company’s standard Network Management System (HP-Openview, CA Unicenter, HP Insight Manager, IBM Tivoli Netview). To simplify
integration of MGE UPSs, you can use one of the Network Management System Kits for MGE devices. These kits are available on the
Management Pac 2 CD-ROM. (ref 66923)
the MGE supervisor "Enterprise Power Manager"
1.1.4 Connection
Before installing the MGE Network Solution, the UPS must be set up as indicated in the steps below.
Shut down the computers to be protected by the UPS.
Connect the UPS to a wall outlet. (For UPSs above 3kVA, please refer to the UPS installation manual)
Connect the power cord of each computer to an outlet on the UPS. (For UPSs above 3kVA, please refer to the UPS installation manual)
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-5-
1.1.4.1 How to connect UPS / agent / network:
Insert the optional card in the UPS and connect the UPS to the computer network.
Start the MGE UPS, then the computers.
1.1.4.2 Setting up the protection:
Set up the Network Management Card (see user manual).
Install and configure the Network Shutdown Module on all machines that are to be protected by the UPS.
The software components for each platform and the user manuals are on the Solution-Pac-2 CD or are available for download on the
www.mgeups.com Web site, in the “Download area” section.
1.2
Presentation of the Network Management Card (NMC)
1.2.1 Compatibility with UPSs
The Minislot Network Management Card is compatible with the following UPSs:
Pulsar Evolution 500 / 800 / 1100
From technical level 06
Pulsar Evolution 2200 / 3000
From technical level 05
Pulsar Evolution 1500
From technical level 05
EXtreme C 700 / 1000 / 1500
From technical level B2
EXtreme C 2200 - 3200
From technical level 02
Pulsar EX 700 / 1000 / 1500 RT (US°)
From technical level 03
Pulsar EX 2200 / 3200 (US°)
From technical level 09
Pulsar M 2200 / 3000
All models
Pulsar 700 / 1000 / 1500
All models
Note:
If the UPS's NT is below that indicated in the table above, contact MGE's technical support.
The Network Management Card (66102) is not compatible with Pulsar EX 7/10, Pulsar EX 15/20/30, Pulsar ESV+, 8/11/14/22 ranges.
Network Management Cards acquire information on the operation status of the UPS systems and provide remote control of these systems by
means of an ETHERNET network from any SNMP administration station or Web browser.
They also supply alarms to the Network Shutdown Modules to trigger shutdown or other automatic actions for protected servers.
Network Management Cards are compatible with the "Enterprise Power Management" supervision system and with the MGE UPS SYSTEMS
network protection system.
Z
Network Shutdown Module
Z
Entreprise Power Manager
Z
Management-Pac 2
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-6-
1.2.2 Direct sending of E-mail
When a UPS event occurs, the Network Management Card can directly notify up to 4 intranet or extranet addresses by e-mail. (see E-mail
Notification and E-mail message settings)
1.2.3 Sending text messages (SMS)
The card offers the possibility of redirecting UPS alarms to an e-mail server. The format of these e-mails is compatible with mobile telephone
e-mail/SMS transfer systems proposed by ISPs. The format to be used depends on the service provider. For example,
sms.0660256585@votre-login.activmail.net (text messages).
1.2.4 Compatibility with the Network Managment Systems (NMS) – Trap sending
The Network Management Cards are compatible with the major Network Management Systems (IBM Tivoli, CA Unicenter, HP Insight
Manager). The Management-Pac 2 offering includes the necessary SNMP plug-ins to allow an easy integration in the NMS. Events are
notified by SNMP trap.
Z
NMS can subscribe on page “Notified Applications”
Z
The trap list is given in the appendix.
1.2.5 Environment Sensor (option)
The Environment Sensor (66846) solution comprises a box to be connected to the Card Settings port of the Network Management
Cards.
Environment Sensor enables measurement of temperature and humidity around the UPS, consideration of external alarms via 2 dry
contacts and notification of alarms according to pre-programmed thresholds. (see Environmen Status and Environment Configuration)
1.3
Technical data
1.3.1 Hardware characteristics
Dimensions
Z
Dimensions (L x l x H)
132 x 66 x 42 mm
Z
Weight (gr)
70 g.
Storage
Z
Storage temperature
-10°C to 70°C
Ambient conditions
Z
Operating temperature
0°C to 40°C
Z
Ambient humidity
90% RH max without condensation
Z
RoHS
100% compatible
1.3.2 EMC Compatibility
When correctly installed and used in accordance with the manufacturer's instructions, the Network Management Card complies with the
following standards:
Z Safety for ATI: IEC/EN 60950-1 2002
Z EMC: EN 61000-6-2 (2002), EN 61000-6-3 (2002). IEC/EN 62040-2 (2002)
As per European directives:
Z Low voltage: 73/23/EEC and 93/68/EEC.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-7-
Z EMC: 89/336/EEC and 93/68/EEC.
1.3.3 Configuration
The user can configure the card with one of the following means:
Z
Web browser
Z
Local serial link (network parameters)
Z
BOOTP/DHCP (network parameters)
1.3.4 Administration
Z
Up to 50 workstations protected by Network Shutdown Modules - Central or local configuration.
Z
Up to 5 browsers connected at the same time (3 in SSL).
Z
Minimum recommended browser versions: Internet Explorer 6.x, Mozilla Firefox 1.5, Netscape 6.x
Z
E-mail sending configurable according to UPS alarms and transmission of a periodical report.
Z
Control of UPS on/off switching via the HTML interface.
Z
Adjustment and control of PowerShare outlets via the HTML interface, sequential starting of the installation and optimisation of backup
Z
Automatic data and time adjustment via NTP server.
Z
Protection by encrypted password.
Z
Protection by secure SSL connection.
Z
Saving of logs in the non-volatile memory.
Z
Languages available: English / French / Spanish / German / Italian
Z
On-line help in English available for each page.
Z
Card firmware updated via the network
time by shutting down non-priority systems.
1.3.5 Network
Z
Fast ETHERNET 10/100 Mbits compatibility with auto-negotiation on the RJ45 outlet
1.3.5.1 List of ports used
Z
BootP, DHCP
Z
HTML
TCP 80
Z
SSL
TCP 443
Z
NSM connection
TCP 5000
Z
SMTP
25
Z
NTP
123
Z
SNMP V1
161
Z
TRAP SNMP
162
UDP 68 , 67
1.3.6 Environment sensor
Z
Temperature measurement from 0 to 70°C with +/- 1°C accuracy
Z
Measurement of humidity from 0 to 100% with +/- 6% accuracy
Z
Min / max time-stamped function for temperature and humidity
Z
Choice of temperature readings in Celsius or Fahrenheit
Z
High and low thresholds, hysteresis and offset adjustable via Web interface
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-8-
Z
Possibility of notification of status changes by e-mail, SMS or SNMP trap
Z
Position detection of 2 dry contacts (maximum sensor/contact distance: 20 m)
Z
Name and status of each configurable contact
Z
Recording of events and measurements in the card log
Z
Possibility of shutting down the installation in the event of a threshold being exceeded or on opening / closure of a dry contact
Z
Connection to the card with straight CAT5 RJ45 network cables (maximum card/sensor distance: 20 m)
Z
Hot installation
1.3.7 MIB (Management Information Base)
Z
Compatible with MIB MGE V1.7
The list of objects managed can be found in the appendix
1.3.8 Default parameters
Function
Parameter
Default value
Possible value
Network
IP address
172.17.16.16
Network IP address
Subnet mask
255.255.0.0
Network IP address
Gateway Address
0.0.0.0
Network IP address
BOOTP/DHCP
Enabled
Active / Deactivated
Firmware Upload
Enabled
Active / Deactivated
SMTP server
smtpserver
31 characters maximum
UPS Contact
Computer Room Manager
49 characters maximum
UPS Location
Computer Room
49 characters maximum
History log interval (sec.)
60
5 to 99999 sec.
Environment log interval (sec.)
300
60 to 99999 sec.
Default Language
English
English / French / Spanish /
System
German / Italian
Manager table
Access control
Date and time
empty
50 maximum
User name
MGEUPS
10 characters maximum
Password
MGEUPS
10 characters maximum
Community name read
public
49 characters maximum
Trap port
161
Non configurable
Date and time adjustment
Synchronise with an NTP server
Synchronise with an NTP server
Synchronise manually
Serial link
T H E
NTP server
pool.ntp.org
49 characters maximum
Speed
9600 baud
Non configurable
Data bits
8
Non configurable
Stop bits
1
Non configurable
Parity
without
Non configurable
Flow control
without
Non configurable
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
-9-
2 Installation
2.1.1 Unpacking and check on contents
The installation kit contents:
Z
A Network Management Card (66102)
Z
A serial communication cable for configuration (34003918)
Z
Installation manual (34003905)
2.1.2 Indications
Ethernet port
LED
Colour
Activity
Description
ACT
Green
Z
Off
Z
On
Z
Z
Z
Flashing
Z
Z
Off
On
100M
Orange
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
Z
Z
Z
Card not connected to the network.
Card connected to the network but
without activity
Port is active in receiving /
transmission
Port operating at 10Mbits/s.
Port operating at 100Mbits/s.
P O W E R
34003991EN/GA
P R O V I D E R
- 10 -
Service port
LED
UPS
Data
RS232
Colour
Green
Orange
Activity
Z
Off
Z
On
Z
Flashing
Z
Z
Off
On
Z
Flashing
Description
Z
Card startup in progress.
Z
Communication with UPS in progress
Z
Normal operation.
Communication with the UPS is
operational
Z
Configuration menu is active
Z
Normal
operation.
Configuration
menu is deactived
Z
Communication with the Environment
Sensor (option).
2.1.3 Installation in the UPS
The Network Management Card (66102) can be "hot" installed in all UPSs of the MGE UPS SYSTEMS range equipped with a Minislot
without having to shut it down.
Z
Remove the protective plastic cover from the Minislot
Z
Note the card's MAC address prior to insertion
Z
Insert and tighten the card's retaining screws
Z
Connect the ETHERNET cable
Z
Wait 2 min.; the card is completely operational when the green UPS Data LED flashes continuously
2.1.4 Sensor installation (option)
The Environment sensor is available as an option on the Network Management Card and is available from MGE UPS SYSTEMS (reference
66846).
The sensor allows remote monitoring of the UPS's environment through regular measurements: temperature, humidity, status of two external
contacts. It also enables notification of alarms (e-mail, trap SNMP) according to pre-programmed thresholds.
It is connected to the Service port (Settings/Sensor) directly on the Network Management Card with a standard Ethernet cable (20 meters
maximum).
Recognition is automatic. Supervision and configuration are performed via a menu that can be accessed directly from the home page.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 11 -
3 Configuration
3.1.1 Configure IP parameters
Once the card has started:
Connect one end of the cable (34003918) to the Service port.
If the environment sensor was previously connected, the card must be restarted in order to access the configuration menu.
Connect the other end of the cable to the COM port (IOIOI) of a PC.
Launch a HyperTerminal™ type emulator with the following configuration:
Speed: 9600
Data bits: 8
Parity: none
Stop bits: 1
Flow control: none
"Locally reproduce the characters entered" option: deactivated.
Enter MGEUPS or mgeups. The main menu is displayed:
3.1.1.1 Your network is equipped with a DHCP server
The card is configured by default with this service activated.
The card automatically collects IP parameters.
To know the IP parameters, type 2, then type 1. The menu is displayed:
Note the IP address.
To exit, enter 3 then 7. The card is operational.
Note: As long as the card is not connected to the network, it continuously attempts to make connection. Once the connection has been
established, the operational mode presented in the table above becomes effective.
3.1.1.2 Your network is not equipped with a DHCP server
In the main menu enter 2, then 2 again.
Follow the instructions and enter the static IP parameters.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 12 -
At the end of the menu, wait for the "Done" message to be displayed indicating that the IP parameters have been saved.
Return to the main menu and enter 1.
The card restarts with the new IP parameters.
3.1.2 Test after configuration
To check that the Network Management Card is operational after installation and configuration.
From a station connected to the same subnet as the card, open a web browser and enter the IP address of the card in the address field
Check the display of the home page.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 13 -
4 Supervision and administration by browser
Z
On a computer equipped with a Web browser (Internet Explorer, FireFox or Netscape recommended), enter the address initialised
previously in the Installation chapter (e.g. http://172.17.16.16.)
The "UPS properties" home page is displayed.
4.1.1 Optimising the performance of your browser
Z
To view status changes on the UPS in real time, the browser must be configured so that it automatically refreshes all the objects on the
current page.
Example on IE 6: Tools / Internet Options / General / Parameters menu, tick Every time this page is visited and validate.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 14 -
4.2
UPS
4.2.1 UPS properties page
Z
This page gives instant access to the essential information about your UPS.
This page is automatically refreshed every 10 seconds.
4.2.1.1 "UPS" zone: general information on the UPS.
Indication of the picture and generic name of the UPS range
Computer room: Customised name of your system.
You can change this name on the "System" page.
4.2.1.2 "UPS status" zone: Essential information:
Z
The various icons showing the status of the UPS are:
•
Normal operation
•
Alarm present. This icon links directly to the alarm
•
page.
•
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 15 -
•
Utility power present
•
Battery operation
•
Loss of communication with the UPS
•
Battery fault
•
•
•
•
•
(green outlet)
•
Outlet powered
•
(red outlet)
•
Outlet not powered or not protected
"Communication": indicates the status of the communication between the card and the UPS
"Power source": indicates whether the power comes from the utility or from the UPS battery
"Batteries": indicates whether the battery is being charged, discharged, or is faulty
"Output load level": indicates the power percentage used at UPS output
"Master output": indicates if the UPS output is protected
"Controlled outlets": indicates if the controlled outlets (if available) are powered.
4.2.1.3 "Battery status" zone
Z
"Bargraph": graph showing the remaining battery charge (in percent)
Z
"Battery charge level": remaining battery charge (in percent)
Z
"Remaining backup time": Estimation of the battery's maximum backup time remaining before UPS shutdown
Z
"Last periodic test": Result of the last automatic battery test carried out by the UPS
Possible values are:
- OK: the test was completed correctly
– NOK: the battery needs to be checked
– Deactivated: the automatic battery test is not validated on the UPS
The "About your UPS" zone provides information on the UPS and the card, in particular, the model range and software version.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 16 -
4.2.2 On-line help
On-line contextual help in English is available at the top of each page by clicking on the Help link, which is always located on the top right
corner. The navigation menu of the on-line help is identical to that of the card's pages.
The Help page always opens a new window.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 17 -
4.2.3 UPS control
Click on the "UPS Control" section in the menu
UPS configuration may prevent the shutdown and restart commands from being properly run. Read the UPS user manual for more
information.
This page enables triggering of startup and shutdown sequences for the UPS main output and controlled outlets.
Z
The status of each output is displayed by a symbol associated with the Off label (red symbol) or On (green symbol).
Z
The shutdown sequences take into account the time required for the registered servers to shut down without losing data (see shutdown
parameters).
Z
The main outlet has priority over the controlled outlets. Shutdown of the main outlet causes the controlled outlets to shut down. Controlled
outlets can only be started if the master outlet is on.
The Check column proposes six different commands, and a command is only actually started after clicking on 'Execute':
"Safe power down": A sequence to switch off output power is launched immediately. The systems supplied are shut down correctly while the
shutdown sequence is running, then the output is cut.
"Safe power down & reboot": A sequence to switch off then restore output power is launched immediately. The powered systems are shut
down correctly during the shutdown sequence, then the output is switched off.
Finally, the restart sequence is launched at the end of the time delay specified in the "Toggle duration" parameter. The output status is
updated.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 18 -
"Immediate On": A sequence to switch on output power is launched immediately. The output is re-powered and the systems supplied start up
correctly.
"Delayed, safe power down": This is the same switch off sequence as for the "Safe power down" command, but postponed by the number
of seconds programmed in the "Off Delay" parameter.
"Delayed, safe power down & reboot": This is the same switch off then on sequence as for the "Safe power down & reboot" command, but
postponed by the number of seconds programmed in the "Off Delay" parameter.
"Delayed On": This is the same switch on sequence as for the "Immediate On" command, but postponed by the number of seconds
programmed in the "On Delay" parameter.
The Save button saves the Off Delay, Toggle duration and On Delay parameters on the card.
Security: The administrator must click on Save and enter his/her login/password to save modifications or run commands. The default
login and password by default are: MGEUPS
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 19 -
4.2.4 UPS weekly schedule programming
Click on the "Weekly schedule" section of the menu.
UPS configuration may prevent the shutdown and restart commands from being properly run. Read the UPS user manual for more
information.
The weekly schedule enables the administrator to optimise power consumption or program a reboot of the protected equipment at a set time.
In a shutdown sequence, the Network Shutdown Modules connected to the card are informed and ensure that each machine is shut down
correctly before the UPS output is switched off.
Up to 7 UPS shutdown sequences can be programmed in one week, with a minimum shutdown delay of 30 minutes.
The On / Off sequences are valid only if the card's time has been properly set.
Security: The administrator clicks on "Save" and enters his/her login / password to save any edits. The login and password by default are:
MGEUPS
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 20 -
4.2.5 Shutdown parameters
This page enables viewing and configuration of UPS operating parameters in battery mode and for power restoration.
Click on the "Shutdown parameters" section in the menu to see the list of parameters.
When you tick the Show advanced parameters option, extra parameters are displayed. These parameters enable, in particular, adjustment
of certain thresholds related to the percentage of remaining battery charge level.
The Output column enables each outlet to be named (maximum 20 characters).
Note
As priority is given to the main outlet, the card cannot supply the controlled outlets when main outlet power is off.
For the main outlet ("Master" by default)
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 21 -
The first shutdown criteria initiates the restart of the shutdown sequence.
Z
If remaining time is under (0 to 99999 seconds, 180 by default) is the minimum remaining backup time from which the shutdown
Z
If battery capacity is under (0 to 100%); this value cannot be less than that of the UPS and is the minimum remaining battery
sequence is launched.
capacity level from which the shutdown sequence is launched.
Z
Shutdown after (0 to 99999 minutes, not validated by default) is the operating time in minutes left for users after a switch to backup
before starting the shutdown sequence.
Z
Shutdown duration (120 seconds by default) is the time required for complete shutdown of systems when a switch to backup time
is long enough to trigger the shutdown sequences. It is calculated automatically at the maximum of Shutdown duration of
subscribed clients but can be modified in the Advanced mode.
Z
If battery capacity exceeds Minimum battery level to reach before restarting the UPS after utility restoration
.
Important: Certain UPSs do not support this option
For the controlled outlets ("group 1 or group 2" by default)
The page enables programming of operation time and level in backup mode to manage outlet load shedding in the event of electric power
failure:
Z
Switch Off after (from 0 to 99999, 65535 by default) defines the time during which the outlet is supplied starting from the moment
of utility failure. Caution, this time includes the outlet shutdown duration.
Z
Switch Off if battery capacity under (0 by default) is an extra condition for outlet shutdown that can trigger the shutdown
sequence before the shutdown duration runs out.
Z
Shutdown duration is the time required for complete shutdown of the systems supplied by the outlet when an outlet shutdown
sequence is launched.
It is calculated automatically using the maximum shutdown durations of notified applications on the outlets.
Z
Switch On after (from 0 to 99999, default 65535) is the period between main output startup and startup of the relevant
programmable outlet, therefore outlet startup can be delayed in relation to the main output.
Important: Certain UPSs do not support this option
Export settings to file: Enables exportation ("Download" button) and saving of card configuration information.
Import settings from file: Enables selection of a configuration file ("Browse" button) and uploading ("Upload" button) of card configuration
information
Security: The administrator has to click on Save and enter his/her login/password to save any modifications. The login and password by
default are: MGEUPS
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 22 -
4.2.6 Viewing the alarms
Z
Click on "Alarm Table" in the menu to view the list of current alarms. The table of managed alarms is included in the appendix.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 23 -
4.2.7 Measurements
Click on "Measurements" in the menu
The following measurements are saved and time-stamped (env. 430):
Z
"Input voltage": Value of the utility voltage supplying the UPS
Z
"Input frequency": Value of the utility frequency supplying the UPS
Z
"Output voltage": Value of the output voltage of your UPS
Z
"Output load (%)": Value of the percentage of load at UPS output
Z
"Battery capacity (%)": Percentage of charge available in the battery
Z
"Remaining time (min.)": Estimation of the remaining backup time
Z
The save frequency of these values is defined in the "System" page (60 seconds by default). Approximately 435 time-stamps are stored
Z
"Save Log" enables all saved values to be opened or saved in CSV format. (compatible with Excel type spreadsheets)
Z
"Clear Log" enables deletion of all records. Enter the login/password to validate this action.
permanently on the card. The oldest time-stamps are automatically deleted.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 24 -
4.2.8 Event log
Click on "Event Log" in the menu
Z
"Save log" enables all saved values to be opened or saved in CSV format. (compatible with Excel type spreadsheets)
Z
"Clear log" enables deletion of all records. The administrator must enter his/her login / password to validate this action.
The card can save 435 events. The table of managed alarms is included in the appendix.
4.2.9 System log
Click on "System log". in the menu
Z
"Save log" enables all saved values to be opened or saved in CSV format. (compatible with Excel type spreadsheets)
Z
"Clear log" enables deletion of all records. The administrator must enter his/her login / password to validate this action.
The card can save 435 events. The table of managed alarms is included in the appendix.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 25 -
4.3
Notification
4.3.1 Email Notification
The card offers the possibility of redirecting UPS alarms to an e-mail server. The format of these e-mails is compatible with mobile
telephone transfer systems using text messages (SMS).
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 26 -
Z
Recipient List: On the left side of this page, up to four recipients can be configured to receive e-mails from the card. Each addressee
has its own trigger events, selected from the right side of the page, for which an e-mail is sent. The card’s log indicates e-mail
transmission errors
Each recipient is configured with the following parameters
Z
Recipient: (Field is limited to 49 characters) this is the e-mail address of the person or department to receive the e-mail.
The default value is recipientx@domain.com
Z
Attached files: The files selected (Measurements, Event log, System log, Environment measurements) are enclosed with each email sent. The files are sent in CSV format
Z
Periodic report: In addition to the e-mails sent when events occur, a periodic e-mail containing the 3 log files can be sent to the
recipient every x days at the time specified by the user.
To configure the first transmission, specify the day, time and frequency of the next transmission in the "next report" box. After this
date, the page will show the date and time of the next transmission.
Data are sent in CSV format.
Z
Z
Save: Saves any modifications.
Test enables an e-mail to be sent to the recipient immediately. This is one way of checking e-mail transmission, particularly access to the
SMTP server configured in "Network" settings. A transmission report is added to the system log.
The event label in the subject and text of the message is replaced with a test label.
If the user makes any modifications to the page, they must be saved before using the "Test" function.
Z
Notified events:
The right side of the page shows the events that can be notified.
By default, only the main events of battery operation and a few UPS alarms are accessible. All the events appear if the Show/Hide
Events option is actuated.
By default, two events are selected for notification. The user can modify this pre-selection by ticking other events or can, on the contrary,
restore the initial configuration by clicking Set Default.
Z
Email Message Settings: access to the message configuration page
Z
Network Settings: enables the name of the SMTP server to be entered. See page
Z
Export settings to file: Enables exportation ("Download" button) and saving of card parameterisation information.
Z
Import settings from file: Enables selection of configuration file ("Browse" button) and uploading ("Upload" button) of card
configuration information.
Z
Security: The administrator has to click on Save and enter his/her login/password to save any modifications. The default login
and password are: MGEUPS
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 27 -
4.3.2 E-mail Message Settings
This page enables customisation of the content of the messages received by recipients of e-mails sent by the card.
Customisation is common to the four recipients that can be notified (see E-mail notification).
Z
Sender
(59 characters maximum) identifies the source of the message. The default value is ups@domain.com.
This field is free. However, depending on the type of SMTP server configuration, it is possible that the server checks that the domain
name contained in the Sender address exists, and even that the user in the Sender address belongs to this domain.
Z
Subject
enables the user to specify the subject of the e-mail to be sent. By entering some free text and selecting from several optional fields, if
desired, the message subject is built:
- UPS name recalls the name of the UPS; it may or may not be selected.
- UPS location recalls the geographic location of the UPS (see System Settings); it may or may not be selected.
- Event message identifies the event generating the e-mail; it may or may not be selected.
Z
- Message text is a free zone.
The body of the e-mail sent is composed of:
- Message text, which is free text.
- The date and time of the event, as saved in the log.
- URL of the card, enabling a direct link with the card to be established.
– Attachments, as configured for the e-mail recipients .- duplication of the subject, as configured.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 28 -
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 29 -
4.4
Configuration
The parameters of this menu can only be modified after entering the "Login" and "Password". The following screen is proposed automatically:
The default login and password are: MGEUPS
Each field accepts up to 10 characters max.
After the login and password are entered, they remain active for 5 minutes.
If the browser is closed, they will have to be re-entered.
An error in either field results in systematic rejection of the requested action (save, page access, card reboot…). After three unsuccessful
attempts, the browser must be rebooted.
These two fields do not travel "decoded" on the IT network. They are encrypted with an MD5 type algorithm, ensuring total confidentiality.
In the event of password loss, the user can return to the default values via the maintenance menu.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 30 -
4.4.1 Network settings
Click on "Network" in the menu.
This menu enables the administrator to configure the network parameters of the card and authorisation of the remote upgrade of the
embedded system.
Z
IP Address: The IP address of the card (e.g.: 172.17.22.252).
Z
Subnet Mask: The mask of the sub-network of your network (e.g.: 255.255.255.0).
Z
Gateway Address: Indicate the IP address of the gateway to access the stations located outside the card’s subnet (e.g.: 172.17.17.1).
Z
Hostname must be suited to the card. This is the first part of the fully qualified domain name, used by the DNS.
As the card does not support NetBIOS protocol, the hostname will only be sent to DNS if the DHCP server sends it the hostname with
the new IP address. This mechanism is described in the update of the DNS protocol RFC 2136
Z
Domain Name is the domain to which the card belongs. This is the part of the fully qualified domain name that follows the hostname and
is used by the DNS. The default value of the two parameters comprising the fully qualified domain name: ups.domain.com
Z
BOOTP/DHCP: Authorises (choose "Enabled") configuration of network parameters with your BootP/DHCP server when the card is
booted.
Mode of card operation with server: After each startup, the card makes 5 attempts to recover the network parameters. If no response is
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 31 -
received from the server, the card boots with the last saved parameters from the previous start. These parameters are those shown on
the page.
The default value for this parameter is "Enable"
Note 1:
If the hostname is not used, the IP address supplied by the DHCP server must be fixed to maintain connection with the clients installed
on the stations to be protected.
Note 2:
During the first connection, if the DHCP query is not successful, the NMC starts with the following IP configuration:
IP address:172.17.16.16
Subnet mask: 255.255.255.0
Gateway Address: 0.0.0.0
Z
Firmware Upload: Authorise (chose "Enabled") remote updating of the card's embedded software.
The default value for this parameter is "Enabled".
Z
Primary DNS Server: contains the IP address of the main DNS server ensuring conversion of the domain name to IP address.
Z
Secondary DNS Server: contains the IP address of the secondary DNS server ensuring conversion of the domain name to IP address if
Z
SMTP Server: contains the name or IP address of the local server with which the card connects to send e-mails.
the primary DNS server is not available.
It may be filled in either as host + domain name (DNS resolution), or directly with the IP address.
The default value is smtpserver. The card uses the standard port (25) for sending e-mails.
Export settings to file: Enables exportation ("Download" button) and saving of card configuration information.
Import settings from file: Enables selection of a configuration file ("Browse" button) and uploading ("Upload" button) of card configuration
information.
Important note:
The card must be rebooted after any changes to these parameters.. See "System" page
Security: The administrator has to click on Save and enter his/her login/password to save any modifications.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 32 -
4.4.2 System
Click on "System" in the menu.
This menu enables the customisation of the information on the UPS properties pages.
Z
UPS Contact: This text field is limited to 49 characters. Enter the name of the person responsible for UPS administration at IT network
level and/or electrical maintenance. This field does not appear on any other Web page. By default, its value is "Computer Room
Manager".
Z
UPS Location: Enter a description (limited to 49 characters) of the location of the UPS in your installation (e.g. Computer room E1-C066).
This text is displayed in the home page. By default, its value is "Computer Room".
Z
Default Language: Enables initialisation of the browser language at card connection.
Choice of one of the available languages: English, French, German, Spanish, Italian changes the language of the html interface pages
(reboot the browser after modification).
Z
History log interval: [from 5 to 99999 sec., 60 by default]. Measurement save period.
Z
Environment log interval: [from 60 to 99999 sec., 300 by default]. Temperature and humidity measurement save period. Reset
Communication button: performs a remote reboot of the card without modifying the configuration. This action is compulsory for
consideration of any changes made on the "Network Settings" page. Security of this operation is ensured by requesting Login and
Password.
Z
Factory Reset button: enables restoration of the default configuration of all the card’s parameters. TCP/IP parameters: IP address,
subnet mask, gateway and BootP/DHCP value are maintained if the "Keep TCP/IP parameters" option is selected. Security of this
operation is ensured by requesting Login and Password. The default login and password are: MGEUPS
Z
Export settings to file: Enables exportation ("Download" button) and saving of card configuration information.
Z
Import settings from file: Enables selection of a configuration file ("Browse" button) and uploading ("Upload" button) of card
configuration information.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 33 -
4.4.3 Notified Applications
Click on "Notified Applications" in the menu.
Security: The administrator has to enter his/her login/password in order to view this information.
This menu enables:
Z
The addition of the supervision stations receiving traps and configuration of the trap type.
Z
To list all the Notified Applications and the main parameters.
Z
To test the operation of notified applications
Z
by simulating power loss
Z
by sending a real shutdown sequence.
Up to 50 destinations can be managed by the card.
Important note: It is not necessary to add the Network Shutdown Modules protecting your servers in this list. These modules subscribe and
unsubscribe themselves automatically.
Select an entry in the list to modify the values in the edit zone at the bottom of the page. The table displays the following information:
Z
Z
The All button: Allows the following information to be displayed:
Z
Hostname or Address IP: By priority, the hostname of the computer is displayed when the IP address can be converted into a hostname
Nr is the index where the application is stored into the table
by a DNS server or if the application has been entered as a hostname.
Z
Application Name: sent by the application during subscription or entered manually.
Z
Output: number of the UPS output from which the client is powered.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 34 -
Z
Configuration: shows where the parameters of the Network Shutdown Module come from: Local (coming from the application) or Central
(coming from the card).
The Central shutdown configuration is available by clicking on the Configuration link.
Z
Z
Shutdown duration: the shutdown duration necessary to properly shutdown the computer.
Shutdown after: the time available to the user from the power failure until the launch of the shutoff sequence of the UPS and equipment.
This parameter is optional.
Many actions are available on this page:
Z
Remove: Depending on the kind of application, the selected ones will definitively disappear from the table as SNMP applications, or they
will disappear and automatically re-subscribe as Network Shutdown Module applications.
Z
Utility failure Test: Two alarms, 'Utility failure' and 'Utility restored' spaced 60 seconds apart, will be sent to the applications selected,
making sure that the applications can be reached over the network.
Shutdown Test: This test simulates a UPS on battery operation. It enables an easy check to see if the server protection works
correctly.
- No intervention on the UPS is required.
- The applications selected will process the simultaneous alarms and perform an actual shutdown sequence.
WARNING!
- This test will generate a REAL shutdown sequence of the selected servers on which the Network Shutdown Module application is
running.
Z
Add NMS: allows an SNMP trap receiver to be added such as a Network Management System.
Z
Modify NMS: allows an SNMP trap receiver to be modified.
Both buttons open a new window where it is possible to enter the Application name, the Hostname or IP Address, the Trap community
and the severity.
The default severity value is 1 - Warning
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 35 -
4.4.4 Central shutdown configuration
Click on "Notified Applications" in the menu, then "Configuration".
This page is used to define either the "shutdown" or the "notification" settings used by the Network Shutdown Modules that connect to
Network Management Card. These settings are used by the Network Shutdown Modules if they are in central-configuration mode or if their
configuration is not valid.
Z
Shutdown duration: the shutdown duration necessary to properly shutdown the computer.
Z
Shutdown after: the time available to the user from the power failure until the launch of the shutoff sequence of the UPS and equipment.
This parameter is optional. Uncheck the box if you wish not to use this parameter.
Z
Broadcast : Sends network notifications to the Administrators and Users groups on events declared in the server hosting the NSM
If you wish to set up a new configuration for the Network Shutdown Modules already set to "central-configuration mode", proceed as indicated
below:
Z
Change the Network Shutdown Module parameters in the "Notified Applications" page.
Z
Click the "Save" button.
Z
In this page, select the NSMs for which you want to apply the new configuration.
Z
Press the "Remove" button.
Z
The NSMs selected will disconnect then reconnect and use the new configuration.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 36 -
4.4.5 Access control
Click on "Access Control" in the menu.
To access this page, the login and password are systematically requested if they have not already been entered.
This menu enables configuration of the different parameters enabling secure access to the card via a browser or SNMP.
Z
Login: This text field is limited to 10 characters. - Enables secure access and modification of pages. Default value "MGEUPS".
Z
Change / Confirm password: This text field is limited to 10 characters. - Enables secure access to Configuration menu pages. Default
value "MGEUPS".
Z
Current Community Read name: Indicates the SNMP community name used for read operations.
Z
Change Community Read-Only: This text field is limited to 49 characters - Enables the SNMP community name used for read
Z
Security mode: manages the various authentication methods for page access
operations to be changed.
Z
Z
Authentication for configuration: Only the configuration pages are protected by login / password.
Z
Full authentication: All pages are protected by login / password.
Z
SSL and full authentication: All pages are protected by login / password and are only accessible in SSL
SSL Access: When selected, access to the Web interface is made in secure mode (https).
Connections with Network Shutdown Modules stay in standard mode (secure TCP)
SSL Security Implementation:
T H E
SSL
Îversion 3.0
TLS
Îversion 1.0
Method
Î TLS_RSA_WITH_512_MD5
Auth
Î RSA
Key Exchange
Î RSA
Encryption
Î RC4_512
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 37 -
Digest
Î MD5
Changes take effect after a card reboot
Export settings to file: Enables exportation ("Download" button) and saving of card configuration information.
Import settings from file: Enables selection of a configuration file ("Browse" button) and uploading ("Upload" button) of card
configuration information
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 38 -
4.4.6 Date and time
Click on "Date and Time" in the menu.
This menu enables initialisation of the date and time of the card in three different ways.
The date format is always of year/month/day type
Z
Set manually: Enables initialisation of the date and time of the card, with the values entered in the Date and Time fields. This update is
made after clicking on the "Save" button.
Maximum drift is +/- 2 min./month
Z
Synchronize with NTP server: Enables connection with a time server, either available on the company’s internal network or on the Web.
This server communicates GMT time. The IP address or hostname of the time server must be entered, and the time zone of your
geographic area must then be selected from the list. Connection is made with the server and the date and time are set after clicking on
the "Save" button. Time is updated every five hours, thus preventing any drift in the time. After two attempts, if the NTP server is not
accessible, the card shifts to manual mode.
The card uses the NTP protocol (UDP 123 port). The "firewall" must be set to transmit queries outside the intranet. No error message is
generated if the time server contact fails.
Note 1:
The even the card is used in a UPS supporting time-stamping, the card's time is automatically synchronized with that of the UPS.
Note 2:
After startup, if the card is in manual mode or if no NTP server was reached, the card initializes at 01/01/1970
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 39 -
4.4.7 Firmware upload
Click on "Firmware Upload" in the menu.
This menu enables a new firmware version to be uploaded
To upload a new version of the card's firmware, select the file to be loaded using the "Browse…" button and click Upload.
Do not interrupt the operation before the card displays the following screen:
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 40 -
4.5
Environment Sensor (option)
The environment sensor (66846) is an option that enables temperature and humidity to be measured, and indication of the position of two
external contacts. It is connected with a standard network cable to the Card Settings port of the Network Management Card.
The card automatically detects sensor presence. The main menu then displays an additional section "Environment" with the following
elements:
Z
Status
Z
Configuration
Z
Log
Important note: To switch the serial port to the configuration mode, just disconnect the cable and reset the card.
4.5.1 Characteristics
Z
Temperature measurement from 0 to 70 °C with +/- 1°C accuracy
Z
Measurement of humidity from 0 to 100% with +/- 6% accuracy
Z
Min / max time-stamped function for temperature and humidity
Z
Choice of temperature readings in Celsius or Fahrenheit
Z
High and low thresholds, hysteresis and offset adjustable via Web interface
Z
Possibility of notification of status changes by e-mail, SMS or SNMP trap
Z
Position detection of 2 dry contacts (maximum sensor/contact distance: 20 m)
Z
Name and status of each configurable contact
Z
Recording of events and measurements in the card log
Z
Possibility of shutting down the installation safely if one of the thresholds is exceeded or dry contact status change
Z
Connection to the Network Management Card by CAT5 straight RJ45 network cables (maximum card/sensor distance: 20 m)
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 41 -
4.5.2 Environment Status
For both measurements, a graduated gauge proposes the following functions:
The cursor indicates the current value.
Two red zones to the left and right represent the high and low thresholds that can be set on the Environment Settings page.
When the measured value enters one of these zones, an alarm can be notified (see Notification parameter in the Environment Settings
page).
Time-stamped minimum and maximum temperatures show the extreme values recorded since the last Reset Min/Max, a thin dotted line
shows their positions on the gauge.
Min and Max can be forced at any time to the current value by clicking on the Reset Min/Max button.
Calibrate: The sensor is factory-calibrated, but the user can apply an offset to adjust the measurement.
Input #1 and Input #2 show the position of the two contacts acquired by the sensor.
The position is displayed with the parameters entered in the Environment Settings page.
The last status change of each contact is time-stamped.
The Internet browser updates this page every 10 seconds
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 42 -
4.5.3 Environment Settings
The environment sensor measures temperature, humidity and gives the status of the 2 contacts (used for door, alarms or generator unit).
The temperature and humidity thresholds can be adjusted and can trigger notification and correct shutdown of the protected system.
The Sensor name is the function name given to the sensor, usually it enables location of the sensor.
Temperature: Choose the temperature unit (°C or °F) from the selection box.
High threshold: if this value is exceeded, a notification if enabled. The default value is 40 °C / 104 °F.
Low threshold: If this value is exceeded, a notification if enabled. The default value is 5 °C / 41 °F.
Hysteresis must be set to prevent multiple notifications if temperature fluctuates around a threshold.
The default value is 2 °C / -3.6 °F.
The high alarm disappears when the value drops below the High threshold - Hysteresis value
The low alarm disappears when the value returns above the Low threshold - Hysteresis value
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 43 -
Humidity
High threshold: If this value is exceeded, a notification is sent if this is validated. The default value is 90%.
Low threshold: If this value is exceeded, a notification is sent if this is validated. The default value is 5%.
Hysteresis must be set to prevent multiple notifications if humidity fluctuates around a threshold. The default value is 5%.
The high alarm disappears when the value drops below the High threshold - Hysteresis value
The low alarm disappears when the value returns above the Low threshold - Hysteresis value
Input #1 and Input #2: Enter an identifier corresponding to the acquired contact (e.g.: rack door, air conditioning, generator unit, etc.). Max.
length is 28 characters.
when closed and when open: are the names associated to the two contact positions. (e.g.: "open" and "closed" for a door, "On" and "Off" for
a generator).
Each status change triggers a notification if enabled.
When the Notification box is enabled, the following functions are activated for each event selected:
Z
display in the list of current alarms
Z
Consideration in the UPS log
Z
SNMP trap generation
Z
notification by e-mail (if the Environment sensor notification option is enabled in the e-mail notification page)
The list of messages is given in the appendix
System shutdown can be triggered for each notification if this option is enabled. If notification is disabled, the Shutdown option cannot be
used.
Export settings to file: Enables exportation ("Download" button) and saving of card configuration information.
Import settings from file: Enables selection of a configuration file ("Browse" button) and uploading ("Upload" button) of card configuration
information.
Security: The user must be identified to access this page.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 44 -
4.5.4 Log
The two environment sensor measurements: Temperature and Humidity are recorded at an interval defined by the Environment log interval
in the System settings page.
By default, this period is 300 seconds.
Each measurement is dated and stored in the log of the UPS’s communication card.
The size of log files is limited by a time indexing system.
The user can Save the log on his/her workstation at any time, in a CSV format file.
The user can also Clear the files contained in the card to reset the log.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 45 -
5
Server protection
5.1
Set-up of the shutdown parameters
The Network Shutdown Module, on protected server boot, subscribes itself automatically to notified applications list and sends its essential
data:
Z
Z
IP Address or hostname of the server on which it is installed: So that the card can inform it of power events.
Time required to shutdown the server (Shutdown Duration, configurable in the "Set-up" menu of each NSM): The card takes into account
the longest shutdown time of all the Network Shutdown Modules subscribed (This is the Shutdown duration of the Shutdown parameters)
page to manage UPS shutdowns without affecting any of Shutdown Modules connected.
During normal operation, the Network Shutdown Module periodically checks its connection with the card.
In case of a major power event, the card sends information to the Network Shutdown Module which reacts according to the situation.
(shutdown order, programmed actions, messages to the administrator and to users via the network)
When the server shuts down, the Network Shutdown Module unsubscribes itself from the notified applications.
5.1.1 Shutdown criteria managed by the Network Management Card
During an extended power failure, three criteria may cause the server shutdown procedure to be initiated. If several criteria are selected, (See
page Shutdown parameters), the first criterion encountered will launch the shutdown procedure.
At the end of the shutdown procedure, when all servers have been shut down, the UPS may shut down to avoid unnecessary discharge of its
batteries, depending on its configuration.
Utility failure
Battery
capacity
Start of the shutdown sequence
UPS Shut off
Shutdown after :
Delay before
shutdown
100%
Remaining autonomy
If remaining time under
Shutdown if
remainig
capacity under
Shutdown duration
t
0%
Card parameters
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
UPS parameters
P R O V I D E R
- 46 -
5.1.1.1 Backup time before initiating the shutdown procedure (Shutdown After - Shutdown Timer)
When the UPS switches to battery, the Network Management Card starts the Shutdown Timer countdown and launches the system
shutdown procedure at the end of the countdown.
This value must be chosen so that users have time to complete their tasks and disconnect, without exceeding battery backup time.
Note 1:
The Network Shutdown Module can also manage its own Shutdown Timer (configurable in the Shutdown Module"set-up" menu of each
Network Shutdown Module) launched when the UPS switches to battery.
Note that if this criterion is selected to initiate system shutdown, automatic system reboot when power is restored is not guaranteed (e.g.
power restoration if only this system was shut down).
5.1.1.2 Initiating the shutdown procedure when the battery level is lower than: (If Capacity under)
When the card detects that the remaining backup time percentage is less than the configured level, the shutdown sequence is started.
By default, this value is set at 20%.
Note:
The UPS already manages an equivalent parameter for the end of backup pre-alarm.
The card does not accept values less than that programmed in the UPS.
Check the UPS documentation.
5.1.1.3 Shutdown when backup time is less than
When the Network Management Card detects that the percentage of backup time remaining is less than the value set, the shutdown
sequence is started.
5.1.1.4 Shutdown duration
Duration (in seconds) required for the system protected by the Shutdown Modules to shut down.
The Network Shutdown Modules transmit their own "Shutdown duration" to the Network Management Card.
Based on these values (maximum Shutdown duration of all subscribed customer systems) that the card will send to the delayed shutdown
order to the UPS.
5.1.2 Controlled outlets
Certain UPS models are equipped with controlled outlets (generally 2) which are always dependant on the UPS's main outlet.
Shutdown of the main outlet systematically causes shutdown of the programmable outlets.
The following notations are used to identify these outlets:
Z
Main outlet:
Main
Z
Controlled outlet 1
1
Z
Controlled outlet 2
2
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 47 -
Utility failure
Start shutdown
outlet 1
Start shutdown main
output
Utility restore
Utility
Main output
Shutdown duration
main output
Outlet 1
NSM 1 on main
output
Shutdown
duration outlet
1
Shutdown duration 1
Shutdown
duration 2
NSM 2 on outlet 1
Shutdown after:
Shutdown duration 3
NSM 3 on main
output
5.1.3 Protection of a server connected to a controlled outlet
Network Shutdown Modules (NSM) starting with version 3.0 are compatible with the controlled outlets.
After connecting the server electrically to one of the controlled outlets, the NSM must be informed of the outlet number to which it is
connected.
Refer to the documentation of the NSM available on the internet site www.mgeups.com section “Download area – embedded Software.
5.1.3.1 Load shedding or sequential shutdown
It is possible to optimise backup time by shutting down non-priority equipment or sequencing the shutdown of several devices.
Two shutdown criteria are possible:
Z
Shutdown of outlets after a set battery back-up time (After)
Z
Shutdown of outlets at a given battery discharge level (if battery capacity under)
It is possible to specify values for both criteria. The first criterion reached will initiate server shutdown.
5.1.3.2 Sequential startup
It is possible to delay outlet power-on to reduce inrush currents on startup or to sequence the startup of several devices.
Controlled outlet startup after a given time is based on startup of the main outlet.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 48 -
5.2
The different server and UPS shutdown sequences
5.2.1 Extended power outage, shutdown initiated by the Shutdown Timer (Shutdown after)
During battery backup time, the Shutdown Timer of the Network Management Card is reached: After a user-defined backup time period
(Shutdown parameters page), the shutdown of all servers is initiated, followed by the UPS shutdown (depending on its configuration). The
UPS restarts when utility power is restored (depending on its configuration)
Shutdown duration: Maximum value of shutdown times of the Network Shutdown Modules subscribed to the card. This value is updated
each time a client subscribes/ unsubscribes.
Utility failure
Start shutdown
output 1
Start shutdown main
output
Utility restore
Utility
Main output
Shutdown duration
main output
Shutdown after:
NSM 1 on main
output
Shutdown after 1:
Output 1
Shutdown
duration output 1
NSM 2 on output 1
5.2.2 Extended power outage, shutdown initiated by the "Low battery power" message
When the "Low battery power" criterion is displayed, the UPS is shut off after taking into account the shutdown duration of the servers.
"Low battery power": The message appears if either of the two following criteria is checked:
- Low Battery Level
- Low Battery Delay
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 49 -
Utility failure
Start shutdown
output 1
Start shutdown main
output
Utility restore
Utility
Shutdown duration
Main output
Battery capacity
under:
NSM 1 on main
output
Shutdown
duration output 1
Output 1
Battery capacity
under: (output 1)
NSM 2 on output 1
5.2.3 Case of power restoration before the end of the "shutdown duration" counter
If power is restored before the end of the Shutdown Duration, the UPS is shut off after the Shutdown Duration for a time equal to the forced
reboot delay (10 seconds)
Utility failure
Start shutdown
output 1
Start shutdown main
output
Utility restore
Utility
Shutdown
duration
Forced Reboot
Main output
Battery capacity under
:
NSM 1 on main
output
Shutdown
duration output 1
Output 1
Battery capacity
under: (output 1)
NSM 2 on output 1
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 50 -
6 Configuration via RS232
Z
Use the cord supplied with the card.
Z
Connect the card to a computer equipped with a hyperterminal type emulator. The serial link must be set at 9600 baud, 8 bits, no parity,
Z
Check that UPS power is on.
Z
Enter the MGEUPS or mgeups password (non modifiable).
Z
The menu is in English only.
1 stop bit, and without flow control.
----------------------------------------------------------------------------MGE UPS SYSTEMS
NETWORK MANAGEMENT CARD
----------------------------------------------------------------------------1 : Reset
2 : Network configuration
3 : Set Login Password to Default
4 : Return to Default Configuration
5 : Exit
6.1
Choice 1: Restart / Reset
Use this function to restart the card; two choices are possible
1 : Hardware Reset: Equivalent to a restart of the electrical power supply.
2 : Restart application: Restarts only the application part.
6.2
Choice 2: Network Configuration
Use this function to access network settings.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 51 -
6.2.1 Choice 1: Read Network settings
Enables reading of the card's routine settings
6.2.2
Choice 2: Modify Network settings
Enables the modification of network parameters
In DHCP mode, the card can receive the following parameters according to the DHCP server settings
Z
IP address
Z
Subnet Mask
Z
Gateway address
Z
Primary DNS server
Z
Secondary DNS server
The card must be restarted in order for the new parameters to be taken into account.
6.3
Choice 3: Lost password / Set Login Password to Default
In the even the login or password is lost, choice 3 enables the return to the default password:
----------------------------------------------------------------------------MGE UPS SYSTEMS
NETWORK MANAGEMENT CARD
----------------------------------------------------------------------------1 : Reset
2 : Network configuration
3 : Set Login Password to Default
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 52 -
4 : Return to Default Configuration
5 : Exit
7 : Exit
----------------------------------------------------------------------------Wait for the confirmation message.
The card is now accessible via the Web with the password MGEUPS.
Enables the return to the new default password: MGEUPS
6.4
Choice 4: Return to Default Configuration
----------------------------------------------------------------------------MGE UPS SYSTEMS
NETWORK MANAGEMENT CARD
----------------------------------------------------------------------------1 : Reset
2 : Network configuration
3 : Set Login Password to Default
4 : Return to Default Configuration
5 : Exit
7 : Exit
enables restoration of the default configuration of all the card’s
parameters
.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 53 -
7 Appendices
7.1
Tables of alarms and events
7.1.1 Table of alarms
List of time dated alarms
Alarm on
Alarm off
Battery fuse blown
Battery fuse OK
Battery temperature fault
Battery temperature OK
Battery charger fault
Battery charger OK
Charger temperature fault
Charger temperature OK
End of Warranty
LCM message OK
Contact MGE http://www.mgeups.com/lcm
End of battery life
LCM message OK
Contacter MGE http://www.mgeups.com/lcm
End of life of the wearing parts
LCM message OK
Contacter MGE http://www.mgeups.com/lcm
Chopper fault
Chopper OK
Normal AC frequency out of tolerance
Normal AC frequency OK
Normal AC fuses blown
Normal AC fuses OK
Normal AC module fault
Normal AC module OK
Normal AC voltage out of tolerance
Normal AC voltage OK
Bypass AC frequency out of tolerance
Bypass AC frequency OK
Automatic Bypass fault
Automatic Bypass OK
Automatic Bypass overload
Automatic Bypass load OK
Automatic Bypass overtemperature
Automatic Bypass temperature OK
Bypass AC phase out of tolerance
Bypass AC phase OK
Automatic Bypass thermal overload
Automatic Bypass load OK
Load not protected - On Automatic Bypass
Load protected - Return from Bypass
Bypass AC voltage out of tolerance
Bypass AC voltage OK
Load not protected - On Manual Bypass
Inverter limitation
Inverter end of limitation
Inverter fuses blown
Input fuses OK
Inverter fault
Inverter OK
Inverter overload
Inverter load OK
Inverter overtemperature
Inverter temperature OK
Inverter thermal overload
Inverter load OK
Load short circuit
Load OK
Normal AC NOK
Normal AC OK
Low battery
Battery OK
UPS communication failed
UPS communication restored
UPS data base not available
UPS data base OK
UPS on battery
UPS on normal AC
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 54 -
Load not powered
Load powered
UPS internal fault
UPS OK
Battery fault
Battery OK
UPS overload
UPS returns to normal load
UPS overtemperature
UPS temperature OK
Imminent UPS shutoff
UPS OK
<Sensor name>: Temperature is above high threshold xx °C <Sensor name>: La température est au dessus du
seuil haut xx °C
<Sensor name>: Humidity is above high threshold xx %
<Sensor name>: L'humidité est au dessus du seuil
haut xx %
<Sensor name>: Temperature is below low threshold xx °C
<Sensor name>: La température est en dessous du
seuil bas xx °C
<Sensor name>: Humidity is below low threshold xx %
<Sensor name>: L'humidité est en dessous du seuil
bas xx %
<Sensor name>: <Input #1 label> <when closed label>
<Sensor name>: <Input #1 label> <when closed label>
<Sensor name>: <Input #1 label> <when open label>
<Sensor name>: <Input #1 label> <when open label>
<Sensor name>: <Input #2 label> <when closed label>
<Sensor name>: <Input #2 label> <when closed label>
<Sensor name>: <Input #2 label> <when open label>
<Sensor name>: <Input #2 label> <when open label>
7.1.2 Table of UPS events
List of time dated informations
Alarm on
Alarm off
Battery fuse blown
Battery fuse OK
Battery temperature fault
Battery temperature OK
Battery charger fault
Battery charger OK
Charger temperature fault
Charger temperature OK
End of Warranty
LCM message OK
End of battery life
LCM message OK
End of life of the wearing parts
LCM message OK
Outlet 1 open
Outlet 1 closed
Outlet 2 open
Outlet 2 closed
Chopper fault
Chopper OK
Normal AC switch (Q1) open
Normal AC switch (Q1) closed
Normal AC frequency out of tolerance
Normal AC frequency OK
Normal AC fuses blown
Normal AC fuses OK
Normal AC module fault
Normal AC module OK
Normal AC voltage out of tolerance
Normal AC voltage OK
Automatic Bypass switch (Q4S) open
Automatic Bypass switch (Q4S) closed
Bypass AC frequency out of tolerance
Bypass AC frequency OK
Automatic Bypass fault
Automatic Bypass OK
Automatic Bypass overload
Automatic Bypass load OK
Automatic Bypass overtemperature
Automatic Bypass temperature OK
Bypass AC phase out of tolerance
Bypass AC phase OK
Automatic Bypass thermal overload
Automatic Bypass load OK
Load not protected - On Automatic Bypass
Load protected - Return from Bypass
Bypass AC voltage out of tolerance
Bypass AC voltage OK
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 55 -
Battery switch (QF1) open
Battery switch (QF1) closed
Manual Bypass switch (Q3BP) closed
Manual Bypass switch (Q3BP) open
Load not protected - On Manual Bypass
Inverter limitation
Inverter end of limitation
Inverter fuses blown
Input fuses OK
Inverter fault
Inverter OK
Inverter overload
Inverter load OK
Inverter overtemperature
Inverter temperature OK
Inverter thermal overload
Inverter load OK
Output switch (Q5N) open
Output switch (Q5N) closed
Load short circuit
Load OK
Normal AC NOK
Normal AC OK
Low battery
Battery OK
UPS communication failed
UPS communication restored
UPS data base not available
UPS data base OK
UPS on battery
UPS on normal AC
Load not powered
Load powered
UPS internal fault
UPS OK
Battery fault
Battery OK
UPS overload
UPS returns to normal load
UPS overtemperature
UPS temperature OK
Imminent UPS shutoff
UPS OK
< Sensor Name> : Temperature is above high threshold
<Sensor Name> : Temperature is in normal range
<xx> (°C) or (°F)
< Sensor Name> : Humidity is above high threshold <xx> (%) <Sensor Name> : Temperature is in normal range
< Sensor Name> : Temperature is below low threshold <xx> <Sensor Name> : Temperature is in normal range
°C or (°F)
< Sensor Name> : Humidity is below high threshold <xx> (%) <Sensor Name> : Temperature is in normal range
<Sensor name>: <Input #1 label> <when closed label>
<Sensor name>: <Input #1 label> <when open label>
<Sensor name>: <Input #2 label> <when closed label>
<Sensor name>: <Input #2 label> <when open label>>
7.1.3 Table of system alarms
Network Management Card startup
Send test mail SUCCESS
Send test mail ERROR
Send mail to <recipient> ERROR
<Sensor name> Communication failure
<Sensor name> Communication restored
Firmware upgraded
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 56 -
7.2
SNMP objects
7.2.1 MGE MIB
The NMC card implement reduce MGEUPS MIB, with the objects bellow managed.
The entire MIB description is available on www.mgeups.com area “Download area – embedded Softwares.
Le chemin d’accès à la MIB MGEUPS est 1.3.6.1.4.1.705.1.
MIB object
SNMP Format
Add.path
upsmgIdentFamilyName
String
{1,1,0}
upsmgIdentModelName
String
{1,2,0}
upsmgIdentSerialNumber
String
{1,7,0}
upsmgIdentFirmwareVersion
String
{1,4,0}
upsmgConfigLowBatteryTime
seconds
{4,7,0}
upsmgConfigLowBatteryLevel
%
{4,8,0}
upsmgConfigAutoRestart
1(yes) 2(no)
{4,9,0}
upsmgConfigVARating
VA
{4,12,0}
upsmgBatteryRemainingTime
seconds
{5,1,0}
upsmgBatteryLevel
%
{5,2,0}
upsmgBatteryVoltage
deciVolts
{5,5,0}
upsmgBatteryCurrent
deciAmps
{5,6,0}
upsmgBatteryFaultBattery
1(yes) 2(no)
{5,9,0}
upsmgBatteryReplacement
1(yes) 2(no)
{5,11,0}
upsmgBatteryLowBattery
1(yes) 2(no)
{5,14,0}
upsmgBatteryChargerFault
1(yes) 2(no)
{5,15,0}
upsmgBatteryLowCondition
1(yes) 2(no)
{5,16,0}
upsmgInputPhaseNum
{6,1,0}
mginputIndex_1
{6,2,1,1,1,0}
mginputIndex_2
{6,2,1,1,2,0}
mginputIndex_3
{6,2,1,1,3,0}
mginputVoltage_1
DeciVolts
{6,2,1,2,1,0}
mginputVoltage_2
DeciVolts
{6,2,1,2,2,0}
mginputVoltage_3
DeciVolts
{6,2,1,2,3,0}
mginputFrequency_1
DeciHz
{6,2,1,3,1,0}
mginputFrequency_2
DeciHz
{6,2,1,3,2,0}
mginputFrequency_3
DeciHz
{6,2,1,3,3,0}
mginputCurrent_1
DeciAmps
{6,2,1,6,1,0}
mginputCurrent_2
DeciAmps
{6,2,1,6,2,0}
mginputCurrent_3
DeciAmps
{6,2,1,6,3,0}
upsmgInputBadStatus
{6,3,0
upsmgOutputPhaseNum
{7,1,0}
mgoutputPhaseIndex_1
{7,2,1,1,1,0}
mgoutputPhaseIndex_2
{7,2,1,1,2,0}
mgoutputPhaseIndex_3
mgoutputVoltage_1
T H E
{7,2,1,1,3,0}
deciVolts
U N I N T E R R U P T I B L E
Network Management Card – User Manual
{7,2,1,2,1,0}
P O W E R
34003991EN/GA
P R O V I D E R
- 57 -
mgoutputVoltage_2
deciVolts
{7,2,1,2,2,0}
mgoutputVoltage_3
deciVolts
{7,2,1,2,3,0}
mgoutputFrequency_1
deciHz
{7,2,1,3,1,0}
mgoutputFrequency_2
deciHz
{7,2,1,3,2,0}
mgoutputFrequency_3
deciHz
{7,2,1,3,3,0}
mgoutputLoadPerPhase_1
%
{7,2,1,4,1,0}
mgoutputLoadPerPhase_2
%
{7,2,1,4,2,0}
mgoutputLoadPerPhase_3
%
{7,2,1,4,3,0}
mgoutputCurrent_1
deciAmps
{7,2,1,5,1,0}
mgoutputCurrent_2
deciAmps
{7,2,1,5,2,0}
mgoutputCurrent_3
deciAmps
{7,2,1,5,3,0}
upsmgOutputOnBattery
1(yes) 2(no)
{7,3,0}
upsmgOutputOnByPass
1(yes) 2(no)
{7,4,0}
upsmgOutputUtilityOff
1(yes) 2(no)
{7,7,0}
upsmgOutputOverLoad
1(yes) 2(no)
{7,10,0}
upsmgAgentIpAddress
{12,1,0}
upsmgAgentSubnetMask
{12,2,0}
upsmgAgentDefGateway
{12,3,0}
upsmgAgentType
{12,6,0}
upsmgAgentMibVersion
{12,11,0}
upsmgAgentFirmwareVersion
{12,12,0}
upsmgAgentCommUPS
T H E
1(yes) 2(no)
U N I N T E R R U P T I B L E
Network Management Card – User Manual
{12,13,0}
P O W E R
34003991EN/GA
P R O V I D E R
- 58 -
If the Environment Sensor is detected , the following information are managed.
upsmgEnvironAmbientTemp
0.1 degré
{8,1,0}
upsmgEnvironAmbientHumidity
0.1 %
{8,2,0}
upsmgEnvironmentNum
{8,6,0}
upsmgEnvironmentSensorTable
{8,7,0}
upsmgEnvironmentEntry
{8,7,1,0}
upsmgEnvironmentIndex
{8,7,1.1 }
upsmgEnvironmentComFailure
1(yes) 2(no)
{8,7,1.2}
upsmgEnvironmentTemperature
0.1 degré
{8,7,1.3}
upsmgEnvironmentTemperatureLow
1(yes) 2(no)
{8,7,1.4}
upsmgEnvironmentTemperatureHigh
1(yes) 2(no)
{8,7,1.5}
upsmgEnvironmentHumidity
0.1 %
{8,7,1.6}
upsmgEnvironmentHumidityLow
1(yes) 2(no)
{8,7,1.7}
upsmgEnvironmentHumidityHigh
1(yes) 2(no)
{8,7,1.8}
upsmgEnvironmentInput1State
closed(1), open(2)
{8,7,1.9}
upsmgEnvironmentInput2State
closed(1), open(2)
{8,7,1.10}
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 59 -
7.2.2 Table des TRAPS : (1.3.6.1.4.1.705.1.11)
SNMP traps are sent when alarms appears and desappears.
Level : 1:informational , 2:major, 3:critical
MIB TRAP
Trap #
niveau
-upsmgBatteryFault
Trap 1
Level 3
-upsmgBatteryOK
Trap 2
Level 1
-upsmgAtLowBattery
Trap 5
Level 3
-upsmgFromLowBattery
Trap 6
Level 1
-upsmgChargerFault
Trap 7
Level 3
-upsmgChargerOK
Trap 8
Level 1
-upsmgOnBattery
Trap 11
Level 2
-upsmgReturnFromBattery
Trap 12
Level 1
-upsmgOnByPass
Trap 13
Level 2
-upsmgReturnFromByPass
Trap 14
Level 1
-upsmgUtilityFailure
Trap 17
Level 2
-upsmgUtilityRestored
Trap 18
Level 1
-upsmgOverLoad
Trap 21
Level 3
-upsmgLoadOK
Trap 22
Level 1
-upsmgOverTemperature
Trap 23
Level 3
-upsmgTemperatureOK
Trap 24
Level 1
-upsmgOffToStart
Trap 29
Level 2
-upsmgOffInProgress
Trap 31
Level 3
-upsmgCommunicationFailure
Trap 37
Level 3
-upsmgCommunicationRestored
Trap 38
Level 1
If the Environment Sensor is detected , the following information are managed.:
- upsEnvironmentComFailure
Trap 53
Level 2
- upsEnvironmentComOK
Trap 54
Level 2
- upsEnvironmentTemperatureLow
Trap 55
Level 2
- upsEnvironmentTemperatureHigh
Trap 56
Level 2
- upsEnvironmentTemperatureOK
Trap 57
Level 2
- upsEnvironmentHumidityLow
Trap 58
Level 2
- upsEnvironmentHumidityHigh
Trap 59
Level 2
- upsEnvironmentHumidityOK
Trap 60
Level 2
- upsEnvironmentInput1Closed
Trap 61
Level 2
- upsEnvironmentInput1Open
Trap 62
Level 2
- upsEnvironmentInput2Open
Trap 64
Level 2
- upsEnvironmentInput2Closed
Trap 63
Level 2
The level is used to select traps to be sent to the supervisor. This adjustment is available from the “Notified applications” page
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 60 -
8 Glossary
Bootp:
Protocol based on UDP used to allocate an IP address corresponding to an Ethernet card during the startup phase. Defined by the RCF 951
Community name:
Access key to access SNMP agent information
DHCP Dynamic Host Configuration Protocol
This IETF protocol enables remote, automatic, self-configuration of the IP addresses of a workstation.
DNS Domain Name Sevicel
The DNS protocol ensure correspondence between the name of a machine and its IP address
E-mail
Electronic means of transmitting messages and/or files.
Gateway
Interconnection equipment between networks with different conventions, to enable communication between them
HTML
(HyperText Markup Language) Language used to describe hypertext pages on the web.
HTTPS : is the secure version of HTTP, the communication protocol of the World Wide Web. It was invented by Netscape Communications
Corporation to provide authentication and encrypted communication and is used in electronic commerce.
IP
Internet Protocol. Network layer protocol in the TCP/IP stack offering a no-connection inter-network service . The IP protocol offers functions
for addressing, service type specification, fragmentation and re-assembling and security. Defined in RFC 791.
MIB MANAGEMENT INFORMATION BASE
- Group of software commands to control and administrate a device through the network. Each type of device (server, hub, PC, UPS, etc.) has
its own MIB
NETWORK MANAGEMENT CARD
Communication cards to supervise UPS and communicate with Network Shutdown Module to insure power protection on servers
NETWORK MANAGEMENT PROXY
Communication software installed on a PC connected to the UPS to supervise it and communicate with Network Shutdown Module to insure
power protection on servers
NMS NETWORK MANAGEMENT STATION (SNMP)
The dedicated PC or workstation is used on the company’s networks to administrate all devices connected to the network. Data are
transmitted using the SNMP protocol. Popular NMS systems include HP OpenView, IBM Tivoli, CA Unicenter, etc.
NSM : NETWORK SHUTDOWN MODULE
Protection software installed on a PC or server to protect it
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 61 -
NTP Network Time Protocol
Protocol to position a set of machines on a network at the same time.
Programmable outlet (controlled outlet):
Outlet that can be remote-switched on or off. UM-Client components enable management of such outlets.
REBOOT –
To restart a system after an interruption.
– To perform an obstacle-free “reboot”, it is essential that the system is correctly and carefully shut down beforehand.
– The reboot is usually automatic if the computer is re-supplied with electricity (from the utility or from the UPS).
RFC
Request for Comments. All documents defining internal Internet operation.
SNMP (SIMPLE NETWORK MANAGEMENT PROTOCOL)
Protocol used to remote-supervise, administrate and control devices connected to a company network.
SMTP (SIMPLE MAIL TRANSFER PROTOCOL)
Enables message transfer between e-mail servers or between the client and its server. It is based on the server’s port 25. It is described in
RFC 821
SSL (Secure Sockets Layers) is a protocol developed by Netscape Communications Corporation for securing data transmission in
commercial transactions on the Internet. Using public-key cryptography, SSL provides server authentication, data encryption, and data
integrity for client/server communications
Subnet mask:
Mask of bits used to identify and differentiate the network address and the equipment address in an IP address.
Normally, the mask is automatically determined by the class of address, which defines in a unique manner the network part/equipment part
division of the IP address.
- Class A: internet address: 255.0.0.0.
- Class B: internet address: 255.255.0.0.
- Class C: internet address: 255.255.255.0.
TCP/IP
Transmission Control Protocol/Internet Protocol. Common name of a series of protocols developed by the DOD in the US to help build Internet
networks throughout the world.
Telnet
Internet protocol used for terminal emulation, i.e. enabling a computer to connect with a server as if it was a simple terminal locally connected
to this server.
Trap (SNMP)
This term describes an event that affects an MIB variable. Traps are sent to the
manager, which is programmed to perform specific tasks upon reception of the
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 62 -
traps.
T H E
U N I N T E R R U P T I B L E
Network Management Card – User Manual
P O W E R
34003991EN/GA
P R O V I D E R
- 63 -
Download PDF