SF-16 Sea Foam Motor Treatment

SF-16 Sea Foam Motor Treatment
Sea Foam Motor Treatment SF-16, SF-128, SF-55
Sea Foam Trans Tune TT-16, TT-55
Page 1 of 4
MSDS Preparation Date (mm/dd/yyyy): 01/01/2010
MATERIAL SAFETY DATA SHEET
SECTION 1 - PRODUCT AND COMPANY IDENTIFICATION
Product identifier
:
Product Use
Chemical Family
:
:
Sea Foam Motor Treatment SF-16, SF-128, SF-55
Sea Foam Trans Tune TT-16, TT-55
Motor Treatment - Fuel system treatment, Trans Tune - Transmission treatment
Mixture.
Supplier’s name and address:
Manufacturer’s name and address:
Sea Foam Sales Company
Refer to Supplier
12987 Pioneer Trail • Eden Prairie, MN, USA 55347
24 Hr. Emergency Tel #
: 1-800-535-5053 (Infotrac)
NOTE: INFOTRAC emergency number is to be used only in the event of chemical emergencies involving a spill, leak, fire, exposure or accident involving
chemicals.
SECTION 2 - COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients
CAS #
Wt.%
Pale Oil
64742-54-7
Naphtha
64742-49-0
IPA
67-63-0
40.00 - 60.00
25.00 - 35.00
10.00 - 20.00
LC50(4hr)
(Rat, ihl.)
LD50
(Oral, rat)
(Rabbit, dermal)
N/Av
>15000 mg/kg
>5000 mg/kg
N/Av
>5000 mg/kg
N/Av
17000ppm
4720mg/kg
12890mg/kg
SECTION 3 - HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Clear liquid. Typical odor. Warning! Flammable liquid and vapor. Vapors may cause flash fire. Harmful or fatal if swallowed. Can enter the
lungs and cause damage. Harmful if inhaled. May cause nausea, vomiting, headache and other central nervous system effects. Causes
eye irritation. May cause skin irritation. May have fetotoxic effects, based on animal studies.
***POTENTIAL HEALTH EFFECTS***
Target organs
Routes of exposure
: Eyes, skin, respiratory system and digestive system.
: Inhalation:: YES
YES
Skin:
Skin & Eyes: YES
Signs and symptoms of short-term (acute) exposure
Inhalation :
Ingestion:
YES
Absorpti
on:
Inhalation of vapors can cause nasal and respiratory irritation. Exposure to high vapor concentration can cause dizziness, nausea
and central nervous system depression. May be fatal if inhaled. Breathing saturated vapors for a few minutes may be fatal.
Saturated vapors can be encountered in confined spaces and/or under conditions of poor ventilation.
Skin
:
May cause mild skin irritation. May be absorbed and cause symptoms similar to those for inhalation.
Eyes
:
May cause moderate eye irritation.
Ingestion
:
Swallowing may cause irritation, nausea and vomiting. May cause central nervous system depression. May be absorbed and
cause symptoms similar to those for inhalation. Symptoms may include burning pain, vomiting and diarrhea. Aspiration into the
lungs during swallowing or subsequent vomiting may cause chemical pneumonitis, which can be fatal.
Potential chronic health effects
: Prolonged skin contact may cause dermatitis (rash), characterized by red, dry, itching skin. Prolonged
Other important hazards
:
overexposure to product can result in permanent central nervous system changes. May cause lung inflammation
and lung damage with extreme exposures.
Contains material which may be a teratogen. See TOXICOLOGICAL INFORMATION, Section 11.
SECTION 4 - FIRST AID MEASURES
Inhalation
: Immediately remove person to fresh air. If breathing has stopped, give artificial respiration. If breathing is
Skin contact
: Remove/Take off immediately all contaminated clothing. Wash exposed area thoroughly with soap and water for
Eye contact
: Immediately flush eyes with plenty of water for at least 15 minutes. Lift upper and lower lids during flushing to
Ingestion
: Seek immediate medical attention/advice. Do not induce vomiting. Do not give liquids to drink. Never give
difficult, give oxygen by qualified medical personnel only. Seek immediate medical attention/advice.
at least 15 minutes. Get medical attention.
ensure complete removal of chemical. Remove contact lenses. Seek immediate medical attention/advice.
anything by mouth to an unconscious person.If vomiting occurs spontaneously, keep victim's head lowered
(forward) to reduce the risk of aspiration.
Sea Foam Motor Treatment SF-16, SF-128, SF-55
Sea Foam Trans Tune TT-16, TT-55
Page 2 of 4
MSDS Preparation Date (mm/dd/yyyy): 01/01/2010
SECTION 5 - FIRE FIGHTING MEASURES
Fire hazards/conditions of flammability
: Flammable liquid and vapor. Will ignite when exposed to heat, flame and other sources of ignition.
Flash point
: 12.8°C / 55°F
Flash point Method
: TCC
Auto-ignition temperature : N/Av
Lower flammable limit (% by vol.)
Upper flammable limit (% by vol.)
: N/Av
: N/Av
Oxidizing properties
: None known.
Flame Projection Length
: Not applicable.
Flashback observed
:
Not applicable.
Explosion data: Sensitivity to mechanical impact / static discharge
: Not available.
Suitable extinguishing media : Dry chemical, foam, carbon dioxide and water fog.
Special fire-fighting
: Firefighters should wear proper protective equipment and self contained breathing apparatus with full face piece
operated in positive pressure mode. Move containers from fire area if safe to do so. Water spray may be useful
procedures/equipment
in cooling equipment exposed to heat and flame. Direct water or foam spray may cause frothing which can
increase the intensity and range of the fire.
Hazardous combustion products
: Carbon oxides ;nitrogen oxides (NOx) ;Sulphur oxides; Phosphorus compounds; other unidentified organic
compounds; irritating fumes and smoke.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
Personal precautions
: All persons dealing with clean-up should wear the appropriate protective equipment including self-contained
Environmental precautions
Spill response/cleanup
:
: Ventilate area of release. Remove all sources of ignition. Stop spill or leak at source if safely possible. Contain
Prohibited materials
:
breathing apparatus. Keep all other personnel upwind and away from the spill/release. Restrict access to area
until completion of clean-up.
Ensure spilled product does not enter drains, sewers, waterways, or confined spaces.
and absorb spilled liquid with non-combustible, inert absorbent material (e.g. sand), then place absorbent
material into a container for later disposal (see Section 13). Large spills should be collected mechanically
(remove by pumping) for disposal. Use only non-sparking tools and equipment in the clean-up process.
Notify the appropriate authorities as required.
None known.
SECTION 7 - HANDLING AND STORAGE
Safe Handling procedures
: Use in a well ventilated area. Wear suitable protective equipment during handling. Do not breathe vapors or
Storage requirements
: Store in a cool, dry, well-ventilated area. Store away from areas of excessive heat, open flames, sparks, and
Incompatible materials
:
Special packaging materials
:
spray mist. Avoid contact with skin, eyes and clothing. Keep away from heat and sources of ignition. Use proper
bonding and grounding techniques when transferring liquid. Avoid contact with incompatible materials. Wash
thoroughly after handling.
other possible sources of ignition. Keep away from incompatibles. Keep containers tightly closed when not in
use.
Strong oxidizing agents; Strong acids; Alkali metals; Aluminum; Phosgene; Potassium oxides; Crotonaldehyde;
Trinitromethane.
Always keep in containers made of the same materials as the supply container.
SECTION 8 - EXPOSURE CONTROLS AND PERSONAL PROTECTION
Exposure Limits
Ingredients
ACGIH TLV
TWA
STEL
PEL
OSHA PEL
STEL
Pale Oil
5mg/m³ (As 'Oil mist,
mineral')
10mg/m³ (As 'Oil
mist, mineral')
5mg/m³ (As 'Oil
mist, mineral')
N/Av
Naphtha
300ppm (VM&P
Naphtha)
N/Av
300ppm (VM&P
Naphtha) (final rule
limit)
N/Av
200 ppm
400 ppm
400 ppm
N/Av
IPA
Ventilation and engineering
measures
: Provide mechanical ventilation in confined spaces. Use explosion-proof equipment.
Respiratory protection
Skin protection
: If the TLV is exceeded, a NIOSH/MSHA-approved respirator is advised.
: Impervious gloves must be worn when using this product. Advice should be sought from glove suppliers. Wear
long sleeved shirt and pants to minimize exposed skin.
Sea Foam Motor Treatment SF-16, SF-128, SF-55
Sea Foam Trans Tune TT-16, TT-55
Page 3 of 4
MSDS Preparation Date (mm/dd/yyyy): 01/01/2010
Eye / face protection
: Chemical safety glasses with side shields or splash proof goggles. A full face shield may also be necessary.
Other protective equipment : Depending on conditions of use, an impervious apron should be worn. An eyewash station and safety shower
should be made available in the immediate working area.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
Physical state
: Liquid.
Odour
: Typical odor.
pH
: N/Av
Boiling point
: N/Av
Melting/Freezing point
: N/Av
Vapour pressure (mmHg @ 20° C / 68° F)
: N/Av
Vapour density (Air = 1)
: >1
Volatile organic Compounds (VOC's)
: 367g/L
Absolute pressure of container
: N/Av
Appearance
Odour threshold
: Clear liquid.
: N/Av
Specific gravity
: 0.819
Coefficient of water/oil distribution
: N/Av
Solubility in water
: Insoluble.
Evaporation rate (n-Butyl acetate = 1)
: <1
Volatiles (% by weight)
: N/Av
Viscosity
: N/Av
SECTION 10 - REACTIVITY AND STABILITY DATA
Stability and reactivity
: Stable under the recommended storage and handling conditions prescribed. Hazardous polymerisation does not
occur.
Conditions to avoid
: Avoid heat and open flame.
Materials To Avoid And Incompatibility
: See Section 7 (Handling and Storage) section for further details.
Hazardous decomposition products
: None known, refer to hazardous combustion products in Section 5.
SECTION 11 - TOXICOLOGICAL INFORMATION
Toxicological data
Carcinogenic status
Reproductive effects
Teratogenicity
:
:
:
:
There is no available data for the product itself, only for the ingredients. See Section 2.
No components are listed as carcinogens by ACGIH, IARC, OSHA or NTP.
Not expected to have other reproductive effects.
This product contains Isopropanol. Animal evidence suggests Isopropanol may be fetotoxic at doses that are not
maternally toxic.
Not expected to be mutagenic in humans.
Mutagenicity
:
Sensitization to material
: Not expected to be a skin or respiratory sensitizer.
Synergistic materials
: None known or reported by the manufacturer.
Medical conditions aggravated by overexposure
: None known or reported by the manufacturer.
Addtional Health Hazards
: None reported by the manufacturer.
SECTION 12 - ECOLOGICAL INFORMATION
Environmental effects
: The product should not be allowed to enter drains or water courses, or be deposited where it can affect ground
or surface waters. No data is available on the product itself.
Important environmental characteristics
: No data is available on the product itself.
Ecotoxicological
: No data is available on the product itself.
SECTION 13 - DISPOSAL CONSIDERATIONS
Handling for Disposal
: Handle waste according to recommendations in Section 7. Do not allow material to contaminate ground water
Methods of Disposal
: Dispose of in accordance with federal, provincial and local hazardous waste laws. For assistance with your
system.
waste management needs, contact EMCO’s Waste Services Division at (262) 658-4000.
Sea Foam Motor Treatment SF-16, SF-128, SF-55
Sea Foam Trans Tune TT-16, TT-55
Page 4 of 4
MSDS Preparation Date (mm/dd/yyyy): 01/01/2010
SECTION 14 - TRANSPORTATION INFORMATION
Regulatory
Information
UN Number
Shipping Name
FLAMMABLE LIQUID, N.O.S. (Naphtha; Isopropanol )
Class
Packing
Group
3
II
Label
TDG
UN1993
TDG
Additional
information
ERG #128
The listed transportation information applies only to ground transport and does not address regulatory variations due to
changes in package size, mode of shipment, or other regulatory descriptors.
49CFR/DOT
UN1993
49CFR/DOT
ERG #128
The listed transportation information applies only to ground transport and does not address regulatory variations due to
changes in package size, mode of shipment, or other regulatory descriptors.
Additional
information
Flammable Liquids, n.o.s. (Naphtha; Isopropanol )
3
II
SECTION 15 - REGULATORY INFORMATION
Canadian Environmental Protection Act (CEPA) information: All ingredients listed appear on the Domestic Substances List (DSL).
Canadian WHMIS Classification:
Class B2 (Flammable Liquids)
Class D2A (Materials Causing Other Toxic Effects, Very Toxic Material)
Class D2B (Materials Causing Other Toxic Effects, Toxic Material)
This product has been classified according to the hazard criteria of the CPR and the
MSDS contains all of the information required by the CPR.
TSCA: All listed ingredients appear on the Toxic Substances Control Act (TSCA) inventory.
SECTION 16 - OTHER INFORMATION
NFPA / HMIS Ratings:
Health: 1
Flammability: 3
Reactivity: 0
Legend
: ACGIH: American Conference of Governmental Industrial Hygienists
References
:
CAS: Chemical Abstract Services
IARC: International Agency for Research on Cancer
Inh: Inhalation
N/Ap: not applicable
N/Av: not available
NIOSH: National Institute of Occupational Safety and Health
OSHA: Occupational Safety and Health Administration
PEL: Permissible exposure limit
RTECS: Registry of Toxic Effects of Chemical Substances
STEL: Short Term Exposure Limit
TDG: Canadian Transportation of Dangerous Goods Act & Regulations
TLV: Threshold Limit Values
TWA: Time Weighted Average
TSCA: Toxic Substance Control Act
WHMIS: Workplace Hazardous Materials Identification System
Not available.
Prepared for:
Direct all enquiries to:
Sea Foam Sales Company
12987 Pioneer Trail
Eden Prairie, MN, USA 55347
Telephone: (952) 938-4811
Prepared by:
ICC The Compliance Center Inc.
Canada: 1-888-977-4834
USA:
1-888-442-9628
MSDS Preparation Date (mm/dd/yyyy)
: 02/20/2009
END OF DOCUMENT
Personal Protection: X
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement