18SP717

18SP717
18SP717 –
DD13 EGR Actuator Replacement
Service Kit (P/N: EA4731500394)
KIT DESCRIPTION
Service kit (P/N: EA4731500394) contains all the necessary components needed to
replace the exhaust gas recirculation (EGR) actuator on the DD13 from an old to new
style. Parts are not backwards compatible.
KIT CONTENTS
Service kit P/N: EA4731500394, shown in Table 1.
Part No.
EA4701500694
N910105008011
A4711400724
A0029903950
A4711402546
A4712005351
A4712005451
A0029976571
A0019950502
18SP717
Qty.
1
3
1
3
1
1
1
2
2
1
Description
EGR Actuator
Bolt M8x20
EGR Actuator Lever
Nut
Pull Rod
Coolant Line
Coolant Line
Coolant Fitting
Pipe Clamp
Installation Instructions
Table 1
Removal of the DD13 Exhaust Gas Recirculation Valve Actuator
PERSONAL INJURY
To avoid injury, never remove any engine component while the
engine is running.
Remove as follows:
1. Shut off the engine, apply the parking brake, chock the wheels, and perform any
other applicable safety steps.
2. Disconnect the batteries. Refer to OEM guidelines.
18SP717 Page 1 of 4
ELECTRICAL SHOCK
To avoid injury from electrical shock, use care when connecting
battery cables. The magnetic switch studs are at battery voltage.
PERSONAL INJURY
To avoid injury from hot surfaces, wear protective gloves, or allow
engine to cool before removing any component.
3. Open the hood.
4. Drain the coolant.
5. Remove the center exhaust manifold heat shield.
6. Remove the turbocharger heat shield.
7. Remove the EGR pull rod from the EGR valve lever.
8. Note the EGR hot pipe clamp orientation for proper re-installation
9. Remove the EGR hot pipe. Discard the clamps.
10. Remove the coolant line from the EGR valve actuator and cylinder block.
11. Remove the coolant line from the EGR valve actuator and water manifold.
12. Disconnect the EGR valve actuator electrical harness connector from the engine
electrical harness.
13. Remove three bolts and two spacers from the EGR valve actuator and remove
the actuator from the cylinder block.
Installation of the DD13 Exhaust Gas Recirculation Valve Actuator
Install as follows:
NOTICE:
Do not turn on the ignition power until all of the installation steps are completed.
1. Install the EGR actuator (P/N: EA4701500694) with three bolts (P/N:
N910105008011) to the cylinder block. Torque bolts to 30 N·m (22 lb·ft). Note:
The two actuator spacers are no longer used.
NOTICE:
The EGR actuator shaft must be held still using a wrench when removing or installing
the pull rod and lever clamping nuts to avoid damage to the EGR valve actuator internal
end stops.
2. Install the EGR actuator lever (P/N: A4711400724) onto the EGR actuator using
the orientation below. Torque nut to 25 N·m (18 lb·ft).
18SP717 Page 2 of 4
3. Install two fittings (P/N: A0029976571) into the coolant ports on the EGR
actuator. Torque fittings to 35 N·m (25 lb·ft).
NOTICE:
To prevent damage to the coolant inlet and outlet lines, hold the adaptor fittings with
a wrench during line installation.
4. Install the coolant line to the EGR valve actuator and water manifold. Torque
coolant line to EGR valve actuator to 35 N·m (25 lb·ft). Torque the coolant line on
the water manifold to 35 N·m (26 lb·ft).
5. Install the coolant line to the EGR valve actuator and fitting on cylinder block.
Torque coolant line to EGR valve actuator to 35 N·m (25 lb·ft). Torque coolant
line to fitting on cylinder block 40 N·m (29 lb·ft).
NOTICE:
The EGR actuator shaft must be held still using a wrench when removing or installing
the pull rod and lever clamping nuts to avoid damage to the EGR valve actuator internal
end stops.
6. Position the EGR valve actuator pull rod (P/N: A4711402546) onto the
actuator lever.
7. Apply a small amount of copper based, anti-seize compound to the threads on
the clamping nut. Make sure that the anti-seize is applied only to the threads and
does not get on the pull rod bearings.
8. Install nut (P/N: A0029903950) on the lever. Torque nut to 20 N·m (15 lb·ft).
9. Using clamps (P/N: A0019950502), install the EGR hot pipe in the same
orientation as noted during removal. Torque to 12 N·m (9 lb·ft). Be sure the
18SP717 Page 3 of 4
clamp bolt orientation does not interfere with the travel of EGR valve actuator
pull rod.
10. Position the EGR valve actuator pull rod onto the EGR valve lever.
11. Apply a small amount of copper based, anti-seize compound to the threads on
the clamping nut. Make sure that the anti-seize is applied only to the threads and
does not get on the pull rod bearings.
12. Install nut (P/N: A0029903950) on the EGR valve lever. Torque nut to
20 N·m (15 lb·ft).
13. Connect the EGR valve actuator to the engine wiring harness.
14. Install the turbocharger heat shield.
15. Install the center exhaust manifold heat shield.
16. Fill the coolant system.
17. Connect the batteries. Refer to OEM guidelines.
18. For EPA 07 engines, turn the ignition key on in order to slow learn the
EGR actuator.
19. For EPA 10 engines, use DiagnosticLink® to perform the EGR Actuator Slow
Learn Service Routine under the Actions » EGR menu.
20. Close the hood.
Specifications are subject to change without notice. Detroit Diesel Corporation is registered to ISO 9001:2008.
Copyright © Detroit Diesel Corporation. All rights reserved. Detroit™ is a brand of Detroit Diesel Corporation,
a Daimler company.
18SP717 1505 As technical advances continue, specifications will change. Printed in U.S.A.
18SP717 Page 4 of 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement