Vanguard SBVRBP Installation manual

®
CAST IRON STOVE AND B-VENT
(FREESTANDING FIREPLACE HEATER)
BURNER SYSTEM
OWNER’S OPERATION AND INSTALLATION MANUAL
NATURAL GAS BURNER SYSTEM SBVRBN
PROPANE/LP GAS BURNER SYSTEM SBVRBP
REMOTE READY
IMPORTANT: This B-vent burner system must be installed into approved Vanguard cast iron
stove bodies, models SCIVFC series and PSCIVFC series ONLY. See page 3 of this manual.
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury, or loss
of life.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fire department.
WARNING: Improper installation,
adjustment, alteration, service, or
maintenance can cause injury or
property damage. Refer to this
manual for correct installation and
operational procedures. For assistance or additional information
consult a qualified installer, service agency, or the gas supplier.
— Installation and service must
be performed by a qualified installer, service agency, or the
gas supplier.
— This appliance is only for use
with the type of gas indicated on
the rating plate. This appliance is
not convertible for use with other
gases, unless a certified kit is used.
This appliance may be installed in an aftermarket*, permanently located manufactured
(mobile) home, where not prohibited by state or local codes.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
Save this manual for future reference.
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
SAFETY
INFORMATION
1.
WARNINGS
IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, operate, or service this stove and
burner system. Improper use of
this stove and burner system can
cause serious injury or death
from burns, fire, explosions,
electrical shock, and carbon
monoxide poisoning.
2.
3.
DANGER: Carbon monoxide
poisoning may lead to death!
This stove with burner system is a vented
product. If this unit is not properly installed by
a qualified service person with glass door
properly seated and sealed, gas combustion
products can spill into your home.
Carbon Monoxide Poisoning: Early signs
of carbon monoxide poisoning resemble the
flu, with headaches, dizziness, or nausea. If
you have these signs, the burner system may
not have been installed properly. Get fresh
air at once! Have stove with burner system
inspected and serviced by a qualified service
person. Some people are more affected by
carbon monoxide than others. These include
pregnant women, people with heart or lung
disease or anemia, those under the influence
of alcohol, and those at high altitudes.
Propane/LP gas and natural gas are both
odorless. An odor-making agent is added to
each of these gases. The odor helps you
detect a gas leak. However, the odor added
to these gases can fade. Gas may be present
even though no odor exists.
4.
5.
6.
7.
8.
Make certain you read and understand all
warnings. Keep this manual for reference. It
is your guide to safe and proper operation of
this stove with B-vent burner system.
9.
WARNING: Any change to
this stove or burner system or its
controls can be dangerous.
For more information, visit www.desatech.com
This appliance is only for use with the
type of gas indicated on the rating plate.
This appliance is not convertible for use
with other gases unless a certified kit
is used.
For propane/LP burner system, do not
place propane/LP supply tank(s) inside
any structure. Locate propane/LP supply tank(s) outdoors. To prevent performance problems, do not use propane/LP
fuel tank of less than 100 lbs. capacity.
If you smell gas
• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do
not use any phone in your building
• immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions
• if you cannot reach you gas supplier,
call the fire department.
Never install the stove
• in a recreational vehicle
• where curtains, furniture, clothing, or
other flammable objects are less than
42" from the front, top, or sides of
the stove with burner system
• in high traffic areas
• in windy or drafty areas
This stove reaches high temperatures.
Keep children and adults away from hot
surfaces to avoid burns or clothing ignition. Stove will remain hot for a time
after shut-down. Allow surfaces to cool
before touching.
Carefully supervise young children
when they are in the room with stove.
Do not modify this stove or burner system under any circumstances. Any parts
removed for servicing must be replaced
prior to operating burner system.
Turn burner system off and let cool before servicing, installing, or repairing.
Only a qualified service person should
install, service, or repair this stove or
burner system. Have stove and burner
system inspected annually by a qualified service person.
You must keep control compartments,
burners, and circulating air passages
clean. More frequent cleaning may be
needed due to excessive lint and dust from
carpeting, bedding material, pet hair, etc.
Turn off the gas valve and pilot light before cleaning stove or burner system.
2
10. Have venting system inspected annually by a qualified service person. If
needed, have venting system cleaned
or repaired. See Cleaning and Maintenance, page 22.
11. Keep the area around your stove clear
of combustible materials, gasoline, and
other flammable vapor and liquids. Do
not run burner system where these are
used or stored. Do not place items such
as clothing or decorations on or around
stove.
12. Do not use this stove to cook food or
burn paper or other objects.
13. Never place anything on top of stove.
14. Do not use any solid fuels (wood, coal,
paper, cardboard, etc.) in this burner
system. Use only the gas type indicated
on burner system nameplate.
15. This appliance, when installed, must be
electrically grounded in accordance
with local codes or, in the absence of
local codes, with the National Electrical Code, ANS/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
16. Do not obstruct the flow of combustion and ventilation air in any way. Provide adequate clearances around air
openings into the combustion chamber
along with adequate accessibility clearance for servicing and proper operation.
17. Do not install stove with burner system
directly on carpeting, vinyl tile, or any
combustible material other than wood.
The stove must set on a metal or wood
panel extending the full width and depth
of the stove.
18. Do not use stove or burner system if
any part has been exposed to or under
water. Immediately call a qualified service person to arrange for replacement
of the unit.
19. Do not operate burner system if any
log is broken.
20. Do not use a blower insert, heat exchanger insert, or other accessory not
approved for use with this stove.
21. Do not operate burner system with glass
door removed, cracked, or broken.
22. This heater must be properly connected
to a vent system. This heater is equipped
with a vent safety shutoff system.
106707
OWNER’S MANUAL
PRODUCT
IDENTIFICATION
LOCAL CODES
Install and use stove and burner system with
care. Follow all local codes. In the absence
to local codes, use the current National Fuel
Gas Code ANS Z223.1, also known as
NFPA 54* (USA) or the current CAN/CGAB149[.1 or .2] Installation Codes (Canada).
Cast Iron
Stove Body
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
Log Set
HI
LO
LOT
PI
ON
OFF
PRODUCT
FEATURES
OPERATION
This B-vent cast iron stove with burner
system is clean burning and vents vertically.
Heat is generated by both realistic flames
and glowing embers. When used without
the blower accessory, the stove with burner
system requires no electricity making it
ideal for emergency backup heat.
Control Valve
Piezo Ignitor
ON/OFF Switch
(Other Side)
Cast Iron
Stove Body
PIEZO IGNITOR
Vent
Opening
This burner system has a piezo ignitor. This
system requires no matches, batteries, or
other sources to light burner system.
Rear
Cover
Burner
Blower with
Adjustment
Knob (Optional
Installation)
Pilot
Assy
Glass Door
Assy
Lava Rock
Grate Assembly
Glowing Embers
Figure 1 - Vanguard B-Vent Burner System Shown Installed in Approved Vanguard
Cast Iron Stove Body Models SCIVFC Series and PSCIVFC Series Only
106707
3
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
PRE-INSTALLATION
PREPARATION
WARNING: A qualified installer or service person must
install stove and burner system.
Follow all local codes.
CAUTION: This stove with
burner system creates warm air
currents. These currents move
heat to wall surfaces next to stove.
Installing stove next to vinyl or
cloth wall coverings or operating
stove with burner system where
impurities (such as tobacco
smoke, aromatic candles, cleaning fluids, oil or kerosene lamps,
etc.) in the air exist, may discolor
walls.
Corner Installation
with Vertical
Termination
Through Ceiling
On Wall with Vertical
Termination Through
Ceiling
Figure 2 - Common Stove Locations
Ceiling
42"
4"
LOCATION AND SPACE
REQUIREMENTS
Determine the safest and most efficient location for your Vanguard B-vent cast iron
stove. Make sure that rafters and wall studs
are not in the way of the venting system.
Choose a location where the heat output is
not affected by drafts, air conditioning ducts,
windows, or doors. Figure 2 shows some
common locations. Read all venting information in this manual. Be aware of all restrictions and precautions before deciding the
exact location for your stove.
When deciding the location of your stove,
follow these rules:
1. Do not connect this stove and burner
sytem to a chimney flue serving a
separate solid-fuel burning fireplace or
appliance.
2. Due to high temperatures, do not locate this stove in high traffic areas or
near furniture or draperies.
3. Proper clearances must be maintained,
see Figures 3 and 4.
4. This stove is a freestanding unit designed to set directly on the floor. If
your stove is to be installed directly on
carpeting, vinyl tile, or any combustible
material other than wood, it must be
installed on a metal or wood panel extending the full width and depth of the
stove. See Figure 5.
6"
36"
from
Front
Floor
4"
from
Back
Wall
Front
21 1/4"
29"
Figure 3 - Clearances for Standard Installation
26 1/4"
Front
4"
4"
Figure 4 - Clearance for Corner Installation
For more information, visit www.desatech.com
4
19 1/2"
Figure 5 - Stove With Burner System
Bottom Dimensions
106707
OWNER’S MANUAL
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
ASSEMBLY
STOVE BODY ASSEMBLY
1.
2.
3.
4.
5.
6.
7.
8.
Lift off corrugated box enclosing stove
body crating.
Remove all screws fastening the wood
frame enclosure. Spread wood frame open
and lift away from plastic-bagged stove
body. The bottom pieces of pallet wood
will remain bolted to the stove body.
Remove plastic bag from stove body.
Remove back panel from stove and discard (see Figure 6). Use an adjustable
wrench or a 10 mm socket. Remove six
(6) bolts and washers. Keep bolts and
washers to reattach rear cover.
Remove all contents from inside stove
cavity. Contents include:
(1) - Stove bottom (Discard - Not used
with this application)
(4) - Legs with leg leveler bolts
(1) - Bottom door
(3) - Top grates
(1) - Hardware kit bag with fasteners
Carefully lay stove body on back to attach bottom components to stove body
(see Figure 7). Rest stove on drop cloth or
blanket to avoid scratching stove edges.
Remove remaining pallet wood attached to bottom of stove body (see
Figure 8). Use an adjustable wrench to
remove bolts.
Fasten each leg to stove with four (4)
M8 x 1.25 - 20mm bolts. Use a flat
washer and lock washer with each bolt.
Tighten bolts into threaded holes on
stove body (see Figure 9 and Figure 10
on page 6). Use an adjustable wrench
or a 12mm socket.
Bolt
Product
Identification
Label
Back
Stove
Panel
Figure 6 - Removing Back Panel
Top of Stove Unit
Front of
Stove Unit
Front of
Stove
Unit
Top of
Stove
Unit
Pallet
Wood
Bolted to
Bottom of
Stove
Body
Drop
Cloth/
Blanket
Figure 7 - Laying Down Stove On Side
Bolt
Pallet Wood
Front
Bottom Of
Stove Unit
Pallet Wood
Figure 8 - Removing Pallet Wood From The Bottom of The Stove
Door Hinge Step
Bolt Hole
Front
Leg Hole
Door Catch Bolt
With Adjustable
Hex Nuts Hole
Leg Hole
Leg Hole
Bottom Of
Stove Unit
Figure 9 - Locating Threaded Holes for Legs and Door Attachment
Continued
106707
5
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
ASSEMBLY
Continued
9.
Attach stove door by inserting step bolt
through door hinge pivot hole and into
threaded hole in stove body (see Figure 11 and Figure 9 on page 5). Use an
adjustable wrench or a 12mm socket
to fasten step bolt. Tighten step bolt
until snug. Make sure door moves
freely.
Washers
Bolt
Bottom Of
Stove Unit
Leg
Figure 10 - Attaching Stove Legs
Stove
Door
10. Install door catch bolt (M8 x 1.2555mm with two M8 hex nuts) into
threaded hole on stove body (see Figure 9, page 5). Use an adjustable
wrench or a 12mm socket. The catch
bolt has two hex nuts attached to it (see
Figure 12). The top nut is a bolt stop
and the bottom nut is for door leveling
adjustment.
11. Check general catch bolt alignment
with door claw. Make final adjustment
and door leveling after stove is in normal standing position (see Figure 12).
12. Carefully lift stove back up on its four
attached legs.
13. Remove 2 bolts from bottom of stove
and save. Remove bolt from the top of
the stove to remove the front panel assembly (see Figure 13).
14. Lay the front panel assembly face down
on a protected surface. Remove the two
screws that hold the front plate onto the
front surround plate (see Figure 14).
Save these screws.
15. Remove the seven screws and washers
that hold the screen onto the front surround plate. Discard these screws,
washers, and screen. They are for ventfree use only (see Figure 14).
16. Replace the two screws from step 14
to reassemble the front plate and the
front surround plate. Set this assembly
aside until burner system has been installed, logs have been placed inside of
burner system, and glass door to burner
system insert has been replaced.
Stove
Body
Bolt
Front
Assembly
Figure 13 - Removing Front Assembly
Front Surround
Plate
Screws
Screw with
Washer
Screen
Front Plate
Figure 14 - Removing Screen from Front
Assembly
Bolt Stop
Threaded
Hole
Adjusting Nut
Door
Hinge
Door Claw
Catch Bolt
Door
Step
Bolt
Figure 12 - Catch Bolt and Door Claw
Orientation
Bolt
Shoulder
Figure 11 - Attaching Stove Door
For more information, visit www.desatech.com
6
106707
OWNER’S MANUAL
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
ASSEMBLY
INSTALLING OPTIONAL
BLOWER ACCESSORY
NOTICE: If installing blower in an
existing stove burner system with
gas connections, shut off gas
supply and disconnect heater
from gas supply. Contact a qualified service person to do this.
Continued
INSTALLING B-VENT
BURNER SYSTEM INTO
STOVE BODY
1.
1.
2.
2.
Carefully lift burner system and place
into stove body from the rear of stove.
Place the left, right, and center grate tops
into the top of stove body.
3.
Center Top Grate
(Included with Stove Body)
Right Top
Grate
4.
Left Top
Grate
Remove 4 hex screws securing rear cover
to back of stove body (see Figure 16).
Separate bottom cover from rear cover
by loosening the 8 mounting screws
(see Figure 16).
Align the holes in the top mounting tabs
of blower with the holes in wall of rear
cover. Using the 4 screws provided,
mount blower and tighten screws securely (see Figure 17).
Attach thermal switch and bracket to
inside rear cover wall with two hex
head screws provided as shown in Figure 17. After securing bracket to rear
cover, carefully bend along existing
bend line on bracket to almost a 90°
angle (see Figure 17). This will allow
thermal switch to be positioned against
stove rear wall and sense temperature
when in operating mode.
Blower
Control
Knob
Speed
Control
Control
Shaft
Locknut
TOP VIEW
Thermal
Switch
and
Bracket
Screws
Mounting
Holes
Blower
Assembly
Mounting Holes
Figure 17 - Blower Assembly, Speed
Control, and Thermal Switch Locations
LO
P
ON
T
ILO
OFF
HI
Rear Cover
Hex Screws
Burner
System
Mounting
Screws
Stove Body
Hex
Screws
Cast Iron
Stove Body
Figure 15 - Installing Burner System Into
Cast Iron Stove Body
Mounting
Screws
Bottom Cover
Mounting
Screws
Figure 16 - Removing Rear Cover and Bottom Cover from Stove Body
Continued
106707
7
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
CAST IRON STOVE
AND DIRECT-VENT
BURNER SYSTEM
ASSEMBLY
Continued
5.
Place speed control on left inside of rear
cover and push the plastic control shaft
through opening (see Figure 17, page 7).
6. While supporting speed control, secure
control shaft with lock nut by pushing and
turning lock nut with pliers clockwise
until tight against the side of rear cover.
Place control knob provided onto shaft.
7. Place the green ground wire between the
bottom hole on the blower assembly and
the hex screw and tighten (see Figure 18).
8. Connect the blue wire on the blower
assembly to one side of the thermal
switch (see Figure 18).
9. Connect the black wire to the other side
of the thermal switch (see Figure 18).
10. Connect the white wire to the other terminal on the blower motor assembly (see
Figure 18). Make sure the thermal switch
has been properly installed to fit against
back of burner system insert after the rear
cover assembly has been reinstalled.
11. Make sure all wire connections to terminals on blower motor and thermal
switch are securely attached and that
the screw retaining the green ground
wire is tight.
12. Check to make sure that the power cord
is completely clear of the blower wheel
and that there are no foreign objects in
blower wheel.
INSTALLING REAR COVER
1.
2.
3.
WARNING: Never touch the
blower wheel while in operation.
13. Peel off the backing paper and stick the
supplied wiring diagram decal on the
inside of rear cover as shown (see Figure 18).
14. Reattach bottom cover to rear cover
with 8 screws (see Figure 16, page 7).
Make sure that you don’t pinch any
wires during reassembly. Route power
cord through plastic bushing in bottom
of rear cover.
4.
Place rear cover behind stove body.
Rear cover will rest on the bottom ledge
of the stove body.
Place wire harness from ON/OFF
switch under the cast of stove body.
Using hex screws provided, attach
rear cover to back of stove body. See
Figure 19.
IMPORTANT: This rear cover must be
securely in place before venting pipes
are installed.
Open lower door panel on front of stove
to locate valve.
Rear Cover (Shown with
Optional Blower)
ON/OFF
Switch
Hex
Screws
WARNING: Failure to position
the parts in accordance with supplied diagrams or failure to use
only parts specifically approved
with this heater may result in damage or personal injury.
ON/OFF
Switch
Wire
Harness
Speed
Control
Blower
Power
Cord
Figure 19 - Installing Rear Cover (Shown
with Optional Blower Accessory)
Black
Wire
5.
Thermal
Switch
Blue Wire
White
Wire
Power Cord
(Route Through
Plastic Bushing
in Bottom Cover
When
Assembled)
Connect one wire terminal from ON/OFF
switch to the THTP terminal on the valve.
Connect remaining wire terminal to the
TH terminal on the valve. Make sure that
the wire terminals are in the positions on
the unit as pictured in Figure 20. If wires
are not connected as shown, the ON/OFF
switch will not work.
Wiring
Diagram
Decal
To Control
Switch
Screw
Figure 20 - Control Valve Terminals
Green Ground Wire
Figure 18 - Blower Wiring Layout
For more information, visit www.desatech.com
8
106707
OWNER’S MANUAL
CAST IRON STOVE
AND DIRECT-VENT
BURNER SYSTEM
ASSEMBLY
Continued
6.
Connect or reconnect gas supply, see
Connecting Stove/Burner System to
Gas Supply on page 14.
WARNING: A qualified installer or service person must
connect burner system to gas
supply. Follow all local codes.
VENTING
INSTALLATION
WARNING: Read all instructions completely and thoroughly
before attempting installation.
Failure to do so could result in
serious injury, property damage,
or loss of life. Operation of improperly installed and maintained
venting system could result in
serious injury, property damage,
or loss of life.
NOTICE: Failure to follow these
instructions will void the warranty.
INSTALLATION PRECAUTIONS
Consult local building codes before beginning the installation. Only a qualified service person should install venting system.
The installer must follow these safety rules:
• Wear gloves and safety glasses for
protection
• Use extreme caution when using ladders
or when on roof tops
• Be aware of electrical wiring locations
in walls and ceilings
106707
The following actions will void the warranty on your venting system:
• Installation of any damaged venting
component
• Unauthorized modification of the venting system
• Installation of any component part not
manufactured or approved by DESA
International
• Installation other than as instructed by
these instructions
Your Vanguard stove with B-vent burner
system is approved for use with any listed
gas vent. A listed gas vent is a factory made
and listed system designed, and installed
exclusively for removing products of combustion, excess air, and dilution air resulting
from burning fuel gas. Metal vents, the most
common type of vent, employ double wall
construction enclosing an insulating air
space. This air space both helps keep flue
gases warm and reduce heat transferred to
nearby combustibles. This appliance is
equipped with a safety control system designed to protect against improper venting
of combustion products.
It is very important that the venting system
maintain its balance between the combustion air intake and the flue gas exhaust.
Certain limitations apply to vent configurations and must be strictly followed.
WARNING: This gas stove with
burner system and vent assembly
must be vented directly to the outside. The venting system must
NEVER be attached to a chimney
serving a separate solid fuel burning appliance.
TYPE B-VENT INSTALLATION
(Listed B-0 or Greater)
Before beginning installation be sure that the
overall height and gas vent size conform to
building code requirements. Gas vents extending through pitched roofs can extend a
minimum height of at least 600 mm (2')
higher than any obstruction within 3m (10').
Gas vents extending through flat roofs are
required to extend at least 600 mm (2') above
the roof and at least 600 mm (2') higher than
any portion of the building or adjoining building within 3m (10') of the gas vent.
9
• Venting instruction contained in this
manual may or may not appy to your
area. Consult your local authority for requirement in your area.
• Where the gas vent extends through accessible spaces, it should be enclosed to
avoid personal contact and damage. Enclosure walls should have a fire rating
equal to or greater than the floors through
which the gas vent passes except in single
or two-family dwellings.
• Situate the gas vent in the structure so
that it can be installed without cutting
joists, sills, plates, or major load bearing
partitions or members. It is also important to locate the base of the gas vent as
near as possible to the heating appliance.
• This burner system must be properly connected to a venting system. This burner
system is equipped with a vent safety
shutoff system.
• Use only vents labeled "FOR EXTERIOR USE" above the roofline.
• Consult the authority having jurisdiction to
select the correct gas vent diameter. Avoid
using a larger than necessary diameter.
Round Top
Storm Collar
Flashing
Firestop
Spacer
Enclosure
Wall
Gas Vent
Length
Support
Plate
Adjustable
Length
Roof Suport
25mm (1")
Clearance to
Combustible
Material
Keep Electrical
Wires and Building
Insulation Away
from Gas Vent and
Out of the Required
Air Space
25mm (1")
Clearance to
Combustibles
Figure 21 - Typical B-Vent Installation
Continued
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
VENTING
INSTALLATION
INSTALLING VENT SYSTEM
IN A CHASE
Continued
A chase is a vertical box-like structure built
to enclose venting that runs along the outside of a building. A chase is not required for
such venting.
INSTALLATION OF LISTED
B-1 VENT
WARNING: Installation should
only be made by qualified persons who are familiar with the
safety procedures required for
the installation of the product,
who are equipped with the proper
tools and testing instruments,
and who have achieved proper
certification of licensing. Installations made by unqualified persons can result in the risk of injury or electrical shock which can
be serious or even fatal.
Figure 23 - Vertical Venting Configuration
Through Chimney
NOTICE: Treatment of firestops
and construction of the chase
may vary from building type to
building type. These instructions
are not substitutes for the requirements of local building
codes. You must follow all local
building codes.
Note: When installing in a chase, you should
insulate the chase as you would the outside
walls of your home. This is especially important in cold climates. Minimum clearance between vent pipes and combustible
materials such as insulation is 1".
CHECKING VENT CAPACITY
Figures 22 through 24 show other options
for the gas vent. When venting through a
side wall your vent pipe must have the
proper temperature rating (see Figure 24).
Manufacturer's clearances must also be
maintained. Consult the authority having
jurisdiction in your area regarding venting
through side wall.
Figure 24 - Venting Through a Side Wall
Complete all gas piping, electrical, and vent
connections. After adjusting the burner system and lighting the main burners, allow a
couple of minutes for warm-up. Hold a
lighted match just under the rim of the draft
hood relief opening. Proper venting will
draw the flame toward or into the draft hood.
Improper venting, indicated by escape or
spillage of burned gas, will cause match to
flicker or go out. Smoke from a cigarette
will also be pulled into the draft hood if the
vent is drawing properly.
Figure 22 - Vertical Venting Through
Ceiling Using Two 90º Elbows
Figure 25 - Test for Proper Venting
For more information, visit www.desatech.com
10
106707
OWNER’S MANUAL
VENTING
INSTALLATION
Continued
CHIMNEYS
• Complete familiarity with chimney condition, height, size, clearance to combustibles and other factors is essential.
NOTICE: Consult the authority
having jurisdiction in your area
regarding masonry chimney venting applications.
NOTICE: A complete chimney
inspection by a qualified person
should be performed.
• Appliances using B-vent connectors to
vent into a masonry or factory-built
chimney should not exceed 1 1/2 feet in
length for every inch of connector diameter (3" vent connector has a maximum
4 1/2 foot length; 5" connector has maximum 7 1/2 foot length).
• Oversized chimneys should be relined
with appropriate listed relining systems.
• Cleanout access may be required.
Figure 26 - Straight Installation into
Masonry Chimney
106707
RELINING SYSTEMS
• Suitability and approval of relining materials should be determined.
• Condition, size, height, and termination of the chimney to be relined must
be determined.
• No substitution of components should
be made.
• Joints and connectors should be made
according to manufacturer’s instructions.
NOTICE: Consult the authority
having jurisdiction in your area
regarding listed chimney liner
venting applications.
WARNING: Operation of improperly installed and maintained
venting system could result in
serious injury, property damage,
or loss of life.
HIGH ALTITUDE
INSTALLATION
Your Vanguard B-vent burner system has
been AGA tested and approved for elevations from 0-2000 feet and CGA certified for
elevations from 0-4500 feet.
When installing this burner system at an
elevation above 2000 feet (in the USA), you
may need to decrease the input rating by
changing the existing burner orifice to a
smaller size. Reduce input 4% for each 1000
feet above sea level. Check with your local
gas company for proper orifice size identification and proper orifice for your location.
When installing this stove and burner system at an elevation above 4500 feet (in
Canada), check with local authorities.
For assistance with any high altitude installation contact DESA International’s Technical Service Department at 1-800-DESALOG (1-800-337-2564).
Figure 27 - Typical Straight Installation
with Listed Chimney Liner
11
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
TROUBLESHOOTING
VENTING
PROBLEMS
Most venting problems are caused by incorrect vent sizing, improper installation, or
inadequate air supply. A preliminary check
for a field problem might include:
• Using a draft meter to determine if
venting system draft meets
manufacturer’s specifications
• Checking the vent sizing according to
manufacturer’s specifications, appliance
input, and venting configuration
• Examining the entire venting system for
faults such as disconnected joints for
damaged vent sections
• Making sure vent and air openings are
not obstructed
If these procedures do not reveal the source of
the problem, troubleshooting may include
attention to common venting problems.
FLUE GAS SPILLAGE
Spillage occurs when flue gases cannot exit
the vent system and back up into the dwelling. A primary symptom of appliances
equipped with a Vent Safety Shutoff System
(flue spill switch) is unexplained appliance
shutoffs. Other symptoms of flue gas spillage
at the draft hood include condensation on
walls and windows and/or noticeable odors.
Spillage may also result in the release of
carbon monoxide, a colorless, odorless, highly
toxic gas. A simple spillage test can be conducted if spillage is suspected. See Checking
Gas Connection, pages 14 and 15.
CAUSES OF SPILLAGE AND
CORRECTIVE ACTION
Incorrect Vent Sizing
If the vent is too small or too short, spillage
may occur. If the vent is too large, excessive
dilution air may cool flue gases and reduce
draft, causing spillage. The vent cap size
should also be checked. Check
manufacturer’s instructions, appliance input rating, and appropriate sizing tables.
Venting Condition
Loose joints can affect draft and cause spillage. “Mashed” vent sections and damaged
vent caps can restrict flow and cause spillage. Examine and replace as needed.
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
INSTALLATION
Obstructions
Small animals or birds may get into and block
the vent or draft hood outlet. Dust, lint, and
foreign objects may obstruct air inlets. Remove obstructions and clean openings.
Lateral Run
Lengthy hoizontal or non-vertical runs cause
resistance to flow and may reduce draft
enough to cause spillage. The pitch of lateral runs can also be a problem; lateral runs
should be pitched 1/4" rise per foot of horizontal run from the appliance to the vent.
Elbows
Too many elbows cause excessive restriction of flow and may result in spillage.
Usually, two 90º turns can be tolerated in a
properly sized venting system. More than
two may cause problems and necessitate
changing the system.
Negative Pressure in the
Dwelling
An extremely tight house may not supply
adequate combustion and venting air. Use
of mechanical exhaust such as a dryer vent
or range vent may worsen the problem. An
air exchange system must be installed in the
dwelling to correct this problem.
Flue Gas Cooling
Venting exposed to extremely cold temperatures or venting of single wall construction loses heat needed to maintain draft;
massive masonry chimneys absorb needed
heat. If the flue gases cool excessively, draft
is reduced and spillage may result. Use
proper materials, insulate and protect properly, reline when necessary.
Down Drafts
NOTICE: This burner system is
intended for use as supplemental heat. Use this burner system
along with your primary heating
system. Do not install this stove
and burner system as your primary heat source. If you have a
central heating system, you may
run system’s circulating blower
while using heater. This will help
circulate the heat throughout the
house. In the event of a power
outage, you can use this burner
system as your primary heat
source.
CHECK GAS TYPE
Use proper gas type for the burner system
unit you are installing. If you have conflicting gas types, do not install burner system.
See dealer where you purchased the stove
and burner system for proper burner system
according to your gas type.
INSTALLING GAS PIPING TO
STOVE LOCATION
WARNING: A qualified installer or service person must
connect burner system to gas
supply. Follow all local codes.
CAUTION: For propane/LP
units, never connect burner system directly to the propane/LP
supply. This burner system requires an external regulator (not
supplied). Install the external regulator between the burner system
and propane/LP supply.
In certain wind conditions and in certain
relationships with nearby structures and
objects, high pressure conditions may affect
draft negatively. Relocate the vent cap, raise
its height, or use an approved high wind cap.
For more information, visit www.desatech.com
12
106707
OWNER’S MANUAL
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
INSTALLATION
Continued
Installation Items Needed
Before installing stove and burner system,
make sure you have the items listed below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by local codes) (not
provided)
* An CSA/AGA design-certified equipment shutoff valve with 1/8" NPT tap is an
acceptable alternative to test gauge connection. Purchase the CSA/AGA design-certified equipment shutoff valve from your
dealer.
For propane/LP connections only, the installer must supply an external regulator.
The external regulator will reduce incoming
gas pressure. You must reduce incoming
gas pressure to between 11 and 14 inches of
water. If you do not reduce incoming gas
pressure, heater regulator damage could
occur. Install external regulator with the
vent pointing down as shown in Figure 28.
Pointing the vent down protects it from
freezing rain or sleet.
CAUTION: Use only new,
black iron or steel pipe. Internally-tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe of 1/2"
diameter or greater to allow
proper gas volume to burner system. If pipe is too small, undue
loss of pressure will occur.
Installation must include an equipment shutoff
valve, union, and plugged 1/8" NPT tap.
Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from
burner system (see Figure 29).
Check your building codes for any special
requirements for locating equipment shutoff
valve to stoves.
Apply pipe joint sealant lightly to male
threads. This will prevent excess sealant
from going into pipe. Excess sealant in pipe
could result in clogged burner system valves.
Propane/LP
Supply Tank
CAUTION: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.
We recommend that you install a sediment
trap/drip leg in supply line as shown in
Figure 29. Locate sediment trap/drip leg
where it is within reach for cleaning. Install
in piping system between fuel supply and
burner system. Locate sediment trap/drip
leg where trapped matter is not likely to
freeze. A sediment trap traps moisture and
contaminants. This keeps them from going
into burner system gas controls. If sediment
trap/drip leg is not installed or is installed
wrong, burner system may not run properly.
External
Regulator
Vent
Pointing
Down
Figure 28 - External Regulator with Vent
Pointing Down (Propane/LP Only)
CSA/AGA DesignCertified Equipment
Shutoff Valve with
1/8" NPT Tap*
Natural - From Gas
Meter (5" W.C. to 10.5"
W.C. Pressure )
Approved Flexible
Gas Line
LP - From External
Regulator (11" W.C. to
14" W.C. Pressure)
3" Minimum
Cap
Pipe Nipple
Tee Joint
Sediment Trap/Drip Leg
* The CSA/AGA design-certified equipment shutoff valve may be supplied with the
appliance or you can purchase it from your dealer.
Figure 29 - Gas Connection
Continued
106707
13
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
INSTALLATION
Continued
CONNECTING STOVE/
BURNER SYSTEM TO GAS
SUPPLY
Installation Items Needed
• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not
provided)
1. Open lower door panel.
2. Route flexible gas line (provided by
installer) from equipment shutoff valve
to burner system (see Figure 30). Route
flexible gas supply line and attach to
valve.
3. Check all gas connections for leaks. See
Checking Gas Connections.
To Flare Fitting on
Control Valve
Equipment
Shutoff Valve
To Gas
Supply
(Natural)
Flexible Gas Line from
Equipment Shutoff Valve
Provided by Installer
To External
Regulator
(Propane/LP)
Figure 30 - Flexible Gas Line
CHECKING GAS
CONNECTIONS
WARNING: Test all gas piping and connections for leaks
after installing or servicing. Correct all leaks at once.
WARNING: Never use an open
flame to check for a leak. Apply
commercial leak test solution to all
gas joints. Bubbles forming show
a leak. Correct all leaks at once.
Pressure Testing Gas Supply
Piping System
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
1. Disconnect appliance with its appliance
main gas valve (control valve) and
equipment shutoff valve from gas
supply piping systems. Pressures in
excess of 1/2 psig (3.5 kPa) will damage
burner system gas regulator.
2. Cap off open end of gas pipe where
equipment shutoff valve was connected.
3. Pressurize supply piping system by either opening propane/LP supply tank
valve for propane/LP gas burner system or opening main gas valve located
on or near gas meter for natural gas
burner system, or using compressed air.
4. Check all joints of gas supply piping
system. Apply commercial leak test
solution to all gas joints. Bubbles forming show a leak. Correct all leaks at
once.
5. Reconnect burner system and equipment shutoff valve to gas supply. Check
reconnected fittings for leaks.
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see
Figure 31).
2. Pressurize supply piping system by either opening propane/LP supply tank
valve for propane/LP gas burner system or opening main gas valve located
on or near gas meter for natural gas
burner system, or using compressed air.
3. Check all joints from propane/LP supply tank or gas meter to equipment
shutoff valve (see Figure 32 for propane/LP or Figure 33 for natural, page
15). Apply commercial leak test solution to all gas joints. Bubbles forming
show a leak. Correct all leaks at once.
Pressure Testing Burner
System Gas Connections
1.
2.
3.
4.
5.
6.
Open equipment shutoff valve (see Figure 31).
Open propane/LP supply tank valve for
propane/LP burner system or main gas
valve located on or near gas meter for
natural gas burner system.
Make sure control knob of burner system is in the OFF position.
Check all joints from equipment shutoff
valve to thermostat gas valve (see Figure 32 for propane/LP or Figure 33 for
natural, page 15). Apply commercial
leak test solution to all gas joints.
Bubbles forming show a leak. Correct
all leaks at once.
Light burner system (see Lighting Instructions, page 19). Check all other internal joints for leaks.
Turn off burner system (see To Turn Off
Gas to Appliance, page 19).
Open
ON
POSITION
Equipment
Shutoff
Valve
OFF
POSITION
Closed
Figure 31 - Equipment Shutoff Valve
For more information, visit www.desatech.com
14
106707
OWNER’S MANUAL
INSTALLING OPTIONAL
WALL MOUNT SWITCH
GWMS2
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
INSTALLATION
1.
Continued
Propane/
LP Supply
Tank
Equipment
Shutoff
Valve
2.
3.
4.
Gas Valve
Connect one terminal of 25 ft. wire for
the wall switch to the TPTH terminal
on the valve. Connect remaining wire
terminal to the TH terminal on the
valve. Make sure that the wire terminals are in the positions on the unit as
pictured in Figure 34. If wires are not
connected as shown, the switch will
not work.
Route the 25 ft. wire through openings
provided on the sides of the burner system to a convenient location to mount
your switch.
Connect one bare wire end to each of
the terminals of the GWMS2 wall
switch.
Install the wall switch and cover in the
wall.
Figure 32 - Checking Gas Joints for Propane/LP Gas Burner System
To Control
Switch or
Optional
Accessory
Equipment
Shutoff
Valve
Figure 34 - Control Valve Terminals
Gas Meter
INSTALLING OPTIONAL
WALL MOUNTED
THERMOSTAT - GWMT1
WARNING: Installation must
be done by a qualified installer
familiar with low voltage wiring
procedures.
Gas Valve
WARNING: Do not connect
this thermostat to any electrical
source! Electrical shock and/or
fire hazard will occur.
Figure 33 - Checking Gas Joints for Natural Gas Burner System
1.
2.
Open lower door panel. The valve is
attached to the underside of the burner
system assembly.
Disconnect from the valve the wires
running from the ON/OFF switch.
Continued
106707
15
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
INSTALLATION
Continued
3.
4.
5.
6.
Connect one terminal of the wire for
the wall thermostat to the THTP terminal on the valve. Connect remaining
wire terminal to the TH terminal on the
valve. Make sure that the wire terminals are in the positions on the unit as
pictured in Figure 34, page 15. If wires
are not connected as shown the thermostat will not work.
Route the wire to a convenient location to mount your thermostat (no outside wall). IMPORTANT: The wire
must not exceed 25 feet in length.
The thermostat should be mounted 54"
above the floor in a location where
there is good air circulation. Avoid
heat sources such as lamps, direct sunlight, fireplace, or heat and air conditioning ducts.
Gently remove the cover of the thermostat from the base. Grasp the sides
of the cover firmly and pull to separate
from the base.
Feed the electrical wires through the
rectangular slots (from the back) on
each side of the base (see Figure 35).
7.
Connect one bare wire end to each terminal (“W” and “R”) of the thermostat
base (see Figure 36).
8. Install the base to the wall with screws
provided with thermostat.
9. Move the temperature adjustment back
and forth to insure the bi-metal is free
from restrictions.
10. Replace the cover onto the base. (Upon
installation, the thermostat must be allowed to stabilize at room temperature
for a minimum of 30 minutes for proper
operation.)
11. Set the temperature adjustment to the
desired setting. This thermostat has been
electronically calibrated at the factory.
No adjustment or leveling is necessary.
INSTALLING OPTIONAL
WIRELESS HAND-HELD
REMOTE CONTROL
ACCESSORIES - GHRC AND
GHRCTA SERIES
Installing Remote Receiver
1.
2.
3.
4.
5.
Terminal “W”
W
6.
Open bottom door on stove body.
Disconnect wires from THTP and TH
on control valve that lead to the switch
(see Figure 34, page 15). Discard
switch plate, screws, and nuts.
Install battery into receiver battery clip
and connect to terminals (see Figure 37).
Place receiver into valve bracket and
align holes (see Figure 38).
Use push-in fasteners included with
receiver to secure to bracket.
Connect the wires from the receiver to
the valve at TH and THTP (see Figure
34, page 15).
Receiver
Terminal “R”
R
Terminal
Wires
Figure 36 - Thermostat Base Terminal
“W” and “R”
Battery
Clip
9-Volt Battery
Figure 37 - Installing Battery in Receiver
WARNING: Do not connect
this thermostat to a power
source. Electrical shock and/or
fire hazard will occur.
Feed wires through
rectangular slots
LO
P
ON
T
ILO
OFF
I
H
Figure 38 - Installing Remote Receiver
Figure 35 - Back View of Thermostat Base
For more information, visit www.desatech.com
16
106707
OWNER’S MANUAL
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
INSTALLATION
Continued
REMOVING/REPLACING
GLASS DOOR
You must remove glass door to install logs,
lava rock, and ember material. To remove
glass door, you must first remove the front
panel on stove body.
Installing 9-Volt Battery in HandHeld Remote Control Unit
1.
2.
3.
Remove battery cover on back of remote control unit
Attach terminal wires to a 9-volt battery (not included). Place battery into
the battery housing.
Replace battery cover onto remote control unit.
Terminal
Wires
Battery
Cover
Remote
Control Unit
9-Volt
Battery
Bolt
CAUTION: Do not operate this
burner system with a broken
glass door panel or without the
glass door panel securely in
place. For replacement part information see Replacement
Parts, page 26.
1.
2.
3.
4.
Remove 2 bolts from bottom of stove
(if still installed) and one from the top
of stove to remove front panel (see Figure 41).
Remove the screws from the 2 tabs at
the top of the glass door while holding
door securely keeping it from falling
forward (see Figure 42).
Grasp door by both sides and ease it
upward off of the lower bracket (see
Figure 42).
To replace glass door, follow the above
instructions in reverse.
Bolt
Stove Front Panel
Figure 41 - Removing Front Panel from
Stove
Screw
Battery Housing
Figure 39 - Installing Battery in HandHeld Remote Control Unit (GHRC Only)
9-Volt
Battery
Terminal
Wires
Battery Housing
Glass
Door
Remote
Control Unit
Figure 42 - Removing Glass Door from
Burner System
Battery
Cover
Figure 40 - Installing Battery in HandHeld Remote Control Unit (GHRCTA Only)
Continued
106707
17
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
CAST IRON STOVE
AND B-VENT
BURNER SYSTEM
INSTALLATION
4.
Place log #4 (small log) onto the front
left part of the grate making sure the
notches fits over the prong of the grate.
See Figure 46.
5.
Continued
INSTALLING LOGS, LAVA
ROCK, AND GLOWING
EMBERS
NOTICE: Do not put lava rock on
burner or under burner. Placing
lava rock on burner could cause
performance problems.
2
6.
WARNING: Failure to position
the parts in accordance with these
diagrams or failure to use only parts
specifically approved with this
burner system may result in property damage or personal injury.
It is very important to install these logs
exactly as instructed in Figures 43 through
47 . Do not modify logs. Only use logs
supplied with freestanding burner system.
Do not use if any log(s) are broken (see
Replacement Parts, page 26).
1. Remove glass door. See Removing/Replacing Glass Door, page 17.
2. Place log #1 (back log) on top of grate.
Make sure the notches in the bottom of
the log fit over the grate (see Figure 43).
2. Rest log #2 (large front log) on the pins on
the front part of the grate (see Figure 44).
3. Place log #3 (crossover log) onto the
rear and front logs. Make sure it is seated
properly into the notch on the front log
and over the raised triangular portion of
the rear log as shown in Figure 45.
Lava rock may be placed along sides
and front inside burner system bottom.
This may not be visible when you have
replaced the front of the stove. It is
not necessary to use all of the lava rock
provided.
Figure 44 - Installing Log No. 2
7.
3
Pull ember material apart into pieces
no larger than a dime. Place these
pieces loosely and sparingly directly
onto the exposed section of the front
burner and along the space between the
burner and grate prongs (see Figure 47).
This will create the glowing ember appearance as the flame touches the ember material. Do not block air slots by
using too much ember material in one
area. It is not necessary to use all of the
ember material provided.
Replace the glass door and stove
front. See Removing/Replacing Glass
Door, page 17.
WARNING: The glass door
must be securely in place before
running this burner system. Do
not run this burner system if glass
is missing or broken.
Figure 45 - Installing Log No. 3
1
4
Figure 47 - Placing Ember Material on
Burner
Figure 43 - Installing Log No. 1
Figure 46 - Installing Log No. 4
For more information, visit www.desatech.com
18
106707
OWNER’S MANUAL
3.
4.
5.
6.
7.
8.
Set ON/OFF switch located on rear
cover to “OFF”.
2a. Open lower panel.
2b. If Using Optional Hand-Held Remote:
Set selector switch in the OFF position to prevent draining battery.
3. Turn off all electrical power to the
appliance if service is to be performed.
4. Push in gas control knob slightly and
turn clockwise
to “OFF”.
5. Close lower panel.
Shutting Off Burners Only (pilot
stays lit)
You may shut off the burners and keep
the pilot lit by doing one of the following:
1. Turn control knob clockwise
to the PILOT position.
2. Set selector switch in the OFF position.
11. Turn on all electric power to the
burner system.
12. Turn the ON/OFF switch to ON
position.
13. This valve is equipped with a HI/LO
feature Set burner system input as
desired.
14. Close lower panel.
Gas Control
Knob
Variable
Control Knob
9.
LO
OFF
Push in control knob all the way and
hold. Immediately light the pilot by
repeatedly depressing the piezo
spark ignitor until a flame appears.
Continue to hold for about one (1)
minute after the pilot is lit. Release
knob and it will pop back. Pilot
should remain lit. If it goes out, repeat steps 5 through 8.
• If knob does not pop up when released, stop and immediately call
your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn the gas control knob
to “OFF” and call your service
technician or gas supplier.
10. Turn gas control counterclockwise
to “ON”.
1.
HI
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor's phone. Follow
the gas supplier's instructions.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don't try to repair it, call a
qualified service technician. Force or
attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician
to inspect the appliance and to replace any part of the control system and any gas control which has
been under water.
2.
STOP! Read the safety information
in column one.
Set ON/OFF switch located on rear
cover to “OFF”.
Open lower panel.
Turn off all electric power to the
burner system.
Push in gas control knob slightly and
turn clockwise
to “OFF”.
Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety information in column one. If you don't
smell gas, go to the next step.
The pilot is located by the main
burner and should not require accessing for lighting.
Turn knob on gas control counterclockwise
to “PILOT”.
ON
WARNING: If you do not follow these instructions exactly, a
fire or explosion may result causing property damage, personal
injury or loss of life.
1.
TO TURN OFF GAS
TO APPLIANCE
ILOT
FOR YOUR SAFETY
READ BEFORE
LIGHTING
LIGHTING
INSTRUCTIONS
P
OPERATING STOVE
WITH B-VENT
BURNER SYSTEM
Piezo Ignitor
Figure 48 - Control Valve
MANUAL LIGHTING
PROCEDURE
1.
2.
3.
4.
5.
Remove glass door (see Removing/
Replacing Glass Door, page 17).
Follow steps 1 through 8 under Lighting Instructions.
Depress control knob and light pilot
with match.
Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob. Now
follow steps 10 through 14, column 2.
Replace glass door (see Removing/
Replacing Glass Door, page 17).
Continued
106707
19
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
Selector Switch in
Remote Position
(Optional Remote
Control)
LO
ON
ON
OFF
REMOTE
HI
Continued
Control Knob
in On Position
P
OPTIONAL REMOTE
OPERATION
Note: All remote control accessories must
be purchased separately (See Accessories
on page 27). Follow instructions included
with the remote control.
Thermostat Control Operation
(Optional GHRCTA Only) The thermostat control setting on the remote control
unit can be set to any comfort level between WARMER and COOLER. The
burners will turn on and off automatically
to maintain the comfort level you select.
The ideal comfort setting will vary by
household depending upon the amount of
space to be heated, the output of the central heating system, etc.
NOTICE: You must light the pilot
before using the hand-held remote control unit. See Lighting
Instructions, page 19 .
1.
After lighting, let pilot flame burn for
about one minute. Turn control knob
on the control valve to ON position.
Turn flame adjustment knob anywhere between HI and LO. Slide the
selector switch to the REMOTE position. Note: The burners may light if
hand-held remote ON button was on
when selector switch was last turned
off. You can now turn the burners on
and off with either optional hand-held
remote control unit.
IMPORTANT: Do not leave the selector switch in the REMOTE position when the pilot is not lit. This will
drain the battery.
IMPORTANT: Be sure to press the
ON/OFF buttons on the hand-held
remote control unit for up to 3 seconds to assure proper operation.
OFF
ILOT
OPERATING STOVE
WITH B-VENT
BURNER SYSTEM
Flame Adjustment Knob
Figure 49 - Setting the Selector Switch,
control Knob, and Flame Adjustment
Knob for Remote Operation
GHRC Series Operation:
2a. Press the ON/OFF button to turn the
burners on and off. When turning
burners off, the pilot will remain lit.
GHRCTA Series Operation:
2b. Press the AUTO/ON/OFF button on
the hand-held remote control (see
Figure 50). The lights to the left of
the button will show AUTO, ON, or
OFF.
• In the ON mode, the burners will
ignite. The heater is in manual
mode when ON is lit.
3.
• In the AUTO mode, the thermostat
in the hand-held remote unit controls the room temperature. To increase the room temperature, press
the top arrow of the TEMP button.
To lower the room temperature,
press the bottom arrow of the
TEMP button. At higher settings
the heater will run longer.
IMPORTANT: This remote control
has been specially engineered to
take an air temperature sample every 5.5 minutes in the auto mode.
It will not respond immediately to
the temperature setting being
turned up or down.
IMPORTANT: The hand-held remote control unit must be near the
heater. Do not keep the hand-held
remote control unit too close to the
heater. The thermostat on the
hand-held remote control unit will
heat up too quickly and turn the
heater off.
To turn the burner off, press the
AUTO/ON/OFF button until OFF
lights. The pilot will remain lit.
IMPORTANT: To turn the pilot off,
manually turn the control knob on the
heater to the OFF position.
Shows Temperature Setting
Increases Room
Temperature in
AUTO Mode
The Log Heater will
Automatically Cycle between
Pilot and the Heat Setting
that has been Selected
Decreases Room
Temperature in
AUTO Mode
Turns Burner On
or Off and Allows
You to Choose
the Auto Setting
Figure 50 - Hand-Held Thermostat Remote Control Unit Selections
(GHRCTA Only)
For more information, visit www.desatech.com
20
106707
OWNER’S MANUAL
OPERATING STOVE
WITH B-VENT
BURNER SYSTEM
Continued
OPERATING
OPTIONAL GWMT1
WALL MOUNTED
THERMOSTAT
WARNING: Do not connect
the thermostat to a power source.
Electrical shock and/or a fire hazard will occur.
Light the burner system as instructed in
Lighting Instructions on page 19. Set wall
thermostat to desired temperature.
This thermostat has been electronically
calibrated at the factory and requires no
adjustment or leveling.
OPERATING
OPTIONAL BLOWER
ACCESSORY
Blower controls are located on the left
side of the rear cover when standing in
front of stove with burner system installed.
The DA3610TA thermostatically-controlled blower has an ON setting and an
OFF setting. The blower will only run
when the switch is in the ON position. In the
OFF position, the blower will not operate.
Upon installation, the thermostat must
be allowed to stabilize at room temperature for a minimum of 30 minutes for
proper operation.
To turn the burner system off, adjust
thermostat to the lowest setting and turn
the gas control knob back to PILOT. The
pilot will remain lit.
IMPORTANT: To turn the pilot off,
turn the control knob on the heater to
the OFF position.
INSPECTING
BURNERS
Check pilot flame pattern and burner flame
patterns often.
106707
Burner flames will be steady; not lifting or
floating. Flame patterns will be different
from unit to unit and will vary depending on
installation type and weather conditions.
If the vent configuration is installed incorrectly, the flames will lift or “ghost”. This
can be dangerous. Inspect the flames after
installation to ensure proper installation
and performance.
Figure 52 shows a typical flame pattern. If
burner flame pattern differs from that described:
• turn burner system off (see To Turn Off
Gas to Appliance, page 19)
• see Troubleshooting, pages 23 through 25
PILOT ASSEMBLY
The pilot assembly is factory preset for the
proper flame height. Alterations may have
occurred during shipping and handling. Call
a qualified service person to readjust the
pilot if necessary.
The height of the thermopile must be 3/8" to
1/2" above the pilot flame as shown in Figure
51. The flame from the pilot burner must
extend beyond the thermopile.
Figure 52 - Typical Flame Pattern
If your pilot assembly does not meet these
requirements:
• turn burner system off (see To Turn Off
Gas to Appliance, page 19)
• see Troubleshooting, pages 23 through 25
Thermopile
If you are using DA3610TA blower with
optional themostat (wall mount or remote control) for the burner system, your
burner system and blower will not turn
on and off at the same time. The burner
system may run for several minutes before the blower turns on. After the burner
system modulates to the pilot position,
the blower will continue to run. The
blower will shut off after the burner system firebox temperature decreases.
The blower helps distribute heated air
from the stove. Periodically check the top
grates of the stove and remove any dust,
dirt, or other obstructions that will hinder
the flow of air.
BURNER FLAME PATTERN
3/8" to 1/2"
Pilot Burner
Piezo Ignitor
Figure 51 - Pilot Assembly
21
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
CLEANING AND
MAINTENANCE
WARNING: Turn off burner
system and let cool before
cleaning.
CAUTION: You must keep control areas, burners, and circulating air passageways of stove with
burner system clean. Inspect
these areas of stove and burner
system before each use. Have
burner system inspected yearly
by a qualified service person.
Burner system may need more
frequent cleaning due to excessive lint from carpeting, bedding
material, pet hair, etc.
GLASS DOOR
WARNING: Handle glass
door panel with care. Do not
strike, slam or otherwise abuse
glass. Do not operate burner
system with the glass door removed, cracked, or broken.
WARNING: Do not use abrasive cleaners as this may damage
glass. Use a non-abrasive household glass cleaner to clean glass.
Do not clean glass when hot.
Glass must be cleaned periodically. During
start-up it is normal for condensation to
form on the inside of the glass causing lint,
dust, and other airborne particles to cling to
the glass surface. During initial start-up a
slight film may form on the glass due to
paint curing. The glass should be cleaned
several times with a non-amonia, non-abrasive household cleaner and warm water
after the first two weeks of operation. Thereafter, clean the glass two or three times
during each heating season, depending on
the usage and circumstances present. Refer
to Removing/Replacing Glass Door on page
17 of this manual when removing glass door
for cleaning.
WARNING: Only parts supplied by the manufacturer should
be used when replacing broken
or damaged glass door panel (see
Replacement Parts, page 26). This
glass door panel is a complete
unit. No substitute materials may
be used.
CAUTION: Wear gloves and
safety glasses while handling or
removing broken glass. Do not
remove if glass is hot. Keep children and pets away from glass.
If glass has been broken, carefully remove
glass door (see Removing/Replacing Glass
Door, page 17). Vacuum all glass pieces
with a shop vac.
CAUTION: Do not vacuum if
pieces are hot.
Use only the ceramic glass door replacement intended for this burner system (see
Replacement Parts, page 26 for details on
ordering). No substitutions may be made.
See Removing/Replacing Glass Door, page
17 for instructions for replacing glass door.
WARNING: Do not operate
burner system with the glass door
removed, cracked, or broken.
PILOT AND BURNERS
LOGS
• If you remove logs for cleaning, refer to
Installing Logs, Lava Rock, and Glowing
Embers, page 18, to properly replace logs.
• Use a vacuum cleaner to remove any carbon build-up on logs.
• Replace log(s) if broken. See Replacement Parts on page 26.
• Replace ember material periodically as
needed. See Replacement Parts on page 26.
VENTING SYSTEM
Conduct annual inspection of the venting
system following these guidelines:
1. Check areas of venting system that are
exposed to the weather for corrosion (rust
spots or streaks and, in extreme cases,
holes). Have these items replaced immediately by a qualified service person.
2. Remove the vent cap and shine a
flashlight into the vent. Remove any
foreign material.
3. Check for evidence of excessive condensation. Continuous condensation
can cause corrosion of caps, pipes, and
fittings and can be caused by having
excessive lateral runs, too many elbows, or exterior portions of the system being exposed to cold weather.
4. Inspect joints to verify that no pipe section or fitting has been disturbed and
loosened. Check mechanical supports
such as wall straps for rigidity.
• Remove ember material before cleaning burners and replace when cleaning
is complete.
• Burner and controls should be cleaned
with compressed air to remove dust, dirt,
or lint.
• Use a vacuum cleaner or small, soft
bristled brush to remove excess dust, dirt,
or lint.
For more information, visit www.desatech.com
22
106707
OWNER’S MANUAL
TROUBLESHOOTING
WARNING: Turn off burner
system and let cool before servicing. Only a qualified service
person should service and repair
heater.
Note: For additional help, visit DESA
International’s technical service web
site at www.desatech.com.
CAUTION: Never use a wire,
needle, or similar object to clean
pilot. This can damage pilot unit.
Note: All troubleshooting items are listed in
order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at pilot
1. Ignitor electrode not connected to ignitor cable
2. Ignitor cable pinched or wet
1. Reconnect ignitor cable
3. Piezo ignitor nut is loose
4.
5.
6.
7.
When ignitor button is pressed, there is
spark at pilot but no ignition
Broken ignitor cable
Bad piezo ignitor
Ignitor electrode broken
Ignitor electrode positioned wrong
1. Gas supply turned off or equipment
shutoff valve closed
2. Control knob not in PILOT position
3. Control knob not pressed in while in
PILOT position
4. Air in gas lines when installed
5. Depleted gas supply (propane/LP models only)
6. Pilot is clogged
7. Gas regulator setting is not correct
Pilot lights but flame goes out when control
knob is released
1. Control knob not fully pressed in
2. Control knob not pressed in long enough
3. Equipment shutoff valve not fully open
4. Control valve damaged
www.desatech.com
106707
23
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor. Nut
is located behind the mounting bracket.
4. Replace ignitor cable
5. Replace piezo ignitor
6. Replace pilot assembly
7. Replace pilot assembly
1. Turn on gas supply or open equipment
shutoff valve
2. Turn control knob to PILOT position
3. Press in control knob while in PILOT
position
4. Continue holding down control knob.
Repeat igniting operation until air is
removed
5. Contact local propane/LP gas company
6. Clean pilot (see Cleaning and Maintenance, page 22) or replace pilot assembly
7. Replace gas control
1. Press in control knob fully
2. After pilot lights, keep control knob
pressed in 30 seconds
3. Fully open equipment shutoff valve
4. Replace control valve
Continued
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and
Maintenance, page 22) or replace burner
orifice
2. Contact local propane/LP or natural gas
company
3. Reconnect leads (see Wiring Diagram,
page 26)
4. Replace thermopile
2. Inlet gas pressure is too low
3. Thermopile leads disconnected or improperly connected
4. Thermopile is defective
Delayed ignition burner
1. Manifold pressure is too low
2. Burner porting or orifice clogged
1. Contact local propane/LP or natural gas
company
2. Clean burner (see Cleaning and Maintenance, page 22) or replace burner orifice
2. Damaged burner
3. Gas regulator defective
1. Clean burner (see Cleaning and
Maintenance, page 22) or replace burner
orifice
2. Replace damaged burner
3. Replace gas control
Slight smoke or odor during initial operation
1. Residues from manufacturing processes
and logs curing
1. Problem will stop after a few hours of
operation
Heater produces a whistling noise when
burner is lit
1. Turning control knob to HI position
when burner is cold
2. Air in gas line
1. Turn control knob to LO position and
let warm up for a minute
2. Operate burner until air is removed from
line. Have gas line checked by local propane/LP or natural gas company
3. Clean burner (see Cleaning and
Maintenance, page 22) or replace burner
orifice
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
3. Dirty or partially clogged burner orifice
Glass soots
1. Flame impingement on logs
2. Debris around burner air mixer
1. Adjust the log set so that the flame does
not excessively impinge on it
2. Inspect the opening at the base of the
burner to see that it is NOT packed with
any type of material
Burner system produces a clicking/ticking
noise just after burners are lit or shut off
1. Metal expanding while heating or contracting while cooling
1. This is common. If noise is excessive,
contact qualified service person
Remote does not function
1. Battery is not installed or battery power
is low
1. Replace 9-volt batteries in receiver and
remote control
www.desatech.com
For more information, visit www.desatech.com
24
106707
OWNER’S MANUAL
TROUBLESHOOTING
Continued
WARNING: If you smell gas
Shut off gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
•
•
•
•
IMPORTANT: Operating burner system where impurities in air exist may create odors. Cleaning
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create
fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner system produces unwanted odors
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, pages 14 and 15)
Burner system shuts off in use
1. High or gusting winds
1. Burner system has been tested for up to
40mph winds. However, extreme conditions may occur. See Lighting Instructions on page 19
2. Contact local propane/LP or natural gas
company
3. Clean pilot (see Cleaning and Maintenance, page 22)
4. Locate and correct all leaks (see Checking Gas Connections, pages 14 and 15)
5. Tighten glass
2. Low line pressure
3. Pilot is partially clogged
4. Inner vent pipe leaking exhaust gasses
into system
5. Glass too loose and air tight gasket leaks
in corners after usage
6. Bad thermopile
7. Improper vent cap installation
6. Replace faulty component
7. Check for proper installation and freedom from debris or blockage
Gas odor even when control knob is in OFF
position
1. Gas leak. See Warning statement
above
2. Control valve defective
1. Locate and correct all leaks (see Checking Gas Connections, pages 14 and 15)
2. Replace control valve
Gas odor during combustion
1. Gas leak. See Warning statement
above
1. Locate and correct all leaks (see Checking Gas Connections, pages 14 and 15)
Dark residue on logs or inside of burner
system Note: After removing all causes of
residue deposits, completely clean fireplace
and appliance of all residue before reusing
appliance.
1. Improper log placement
1. Properly locate logs (see Installing Logs,
Lava Rock, and Glowing Embers, page 18)
2. Clean out air holes at burner inlets. Periodically repeat as needed
3. Remove blockage or replace burner
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
www.desatech.com
106707
25
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
REPLACEMENT
PARTS
Note: Use only original replacement parts.
This will protect your warranty coverage for
parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If
they can not supply original replacement
part(s), call DESA International’s Technical
Service Department at 1-800-DESA LOG
(1-800-337-2564).
When calling DESA International, have ready
• your name
• your address
• model and serial numbers of your stove
and burner system
• how burner system was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
Usually, we will ask you to return the defective part to the factory.
PARTS NOT UNDER
WARRANTY
Contact authorized dealers of this product.
If they can not supply original replacement
part(s), call DESA International’s Parts Department at 1-800-972-7879 for referral information.
When calling DESA International, have ready
• model number of your stove and burner
system
• the replacement part number
TECHNICAL
SERVICE
You may have further questions about installation, operation, or troubleshooting. If
so, contact DESA International’s Technical
Service Department at 1-800-DESA LOG
(1-800-337-2564).
WIRING DIAGRAM
CAUTION: Label all wires prior
to disconnection when servicing
controls. Wiring errors can cause
improper and dangerous operation. Verify proper operation after servicing.
Variable
Fan Switch
Off
Fan Switch
(N.O.)
1
2
Black
On
Blue
110/115
V.A.C.
Black
Blower
Motor
White
Green
Figure 53 - Blower Wiring Diagram for Thermostat-Controlled Models
SERVICE HINTS
When Gas Pressure is Too Low:
• pilot will not stay lit
• burners will have delayed ignition
• burner system will not produce specified
heat
• propane/LP gas supply might be low
(propane/LP units only)
When Gas Quality is Bad:
• pilot will not stay lit
• burners will produce flames and soot
• burner system will backfire when lit
If you feel your gas pressure is too low or gas
quality is bad, contact your local natural or
propane/LP gas supplier.
You can also visit DESA International’s
technical service web site at
www.desatech.com.
For more information, visit www.desatech.com
26
106707
OWNER’S MANUAL
SPECIFICATIONS
SBVRBN
SBVRBP
21,000-30,000 Btu/h
20,000-28,000 Btu/h
Natural
Propane/LP
Piezo
Piezo
Manifold Pressure
3.5" w.c.
10.0" w.c.
Minimum Inlet Supply Pressure
4.5" w.c.
11.0" w.c.
70%
70%
27" x 26 1/4" x 20"
685.8 x 660.4 x 635mm
23" x 33" x 23"
584.2 x 838.2 x 584.2mm
27" x 26 1/4" x 20"
685.8 x 660.4 x 635mm
23" x 33" x 23"
584.2 x 838.2 x 584.2mm
70 lbs/31.8 kg
75 lbs/34 kg
70 lbs/31.8 kg
75 lbs/34 kg
Gas Type
Ignition
Thermal Efficiency
Dimension, Inches/mm (HxWxD)
Stove and Burner System*
Carton (Insert Only)
Weight, lbs/kg
Burner System
Shipping
* When installed in Amity cast iron stove body (SCIVFC Series and PSCIVFC Series).
ACCESSORIES
Purchase these stove and burner system
accessories from your local dealer. If they
can not supply these accessories, call DESA
International’s Sales Department at 1-800432-2382. for information. You can also
write to the address listed on the back page
of this manual.
WALL MOUNTED
THERMOSTAT CONTROL
KIT GWMT1 (Not Shown)
RECEIVER AND HAND-HELD
REMOTE CONTROL KIT
GHRC
For all models. Allows the heater to be
turned on and off conveniently.
Allows easy wall access to the operation of
your burner system. This will allow you
thermostatic control with the convenience
of a wall switch.
WALL MOUNTED ON/OFF
SWITCH - GWMS2
(Not Shown)
Allows burner system to be turned on and
off with a wall switch.
WA
RM
ER
ON
OF
F
AU
TO
CO
OLE
R
TE
MP
THERMOSTATICALLYCONTROLLED BLOWER KIT
DA3610TA
Provides better heat distribution. Blower
turns off and on automatically, as needed.
Complete installation and operation instructions included in this manual.
RECEIVER AND HAND-HELD
THERMOSTAT REMOTE
CONTROL KIT - GHRCTA
Allows the burner system to be operated in
a manually or thermostatically controlled
mode. You can adjust your heat settings and
turn the heater on or off without leaving the
comfort of your easy chair.
106707
27
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
ILLUSTRATED
PARTS
BREAKDOWN
3
SBVRBN
SBVRBP
6
9
2
11
16
10
4
4
23-3
23 -1
22
23-4
17
18
21
8
4
19
1
4
23-2
12
25
4
14
24
13
5
20
15
20
LO
H
P
ON
T
IL O
OFF
I
7
For more information, visit www.desatech.com
28
106707
OWNER’S MANUAL
PARTS LIST
This list contains replaceable parts used in your burner system. When ordering parts, follow the
instructions listed under Replacement Parts on page 26 of this manual.
SBVRBN
SBVRBP
KEY
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
23-1
23-2
23-3
23-4
24
25
PART NUMBER
107745-01
105795-01
106836-02CK
M11084-46
106794-01
099998-01
103284-07
103284-06
11200
105494-01
M11084-43
105468-01
105489-01
105489-02
105488-01
105488-02
102445-01
106669-01
106036-01
106036-02
104506-16
104506-17
104507-01
901063-01
101628-04
105325-01
105491-01
105774-01
105774-02
105774-03
105774-04
098304-03
M12461-50
DESCRIPTION
QTY.
Firebox Assembly
Glass Door Assy
Rear Cover
Screw, Hex
Grate Assembly
On/Off Switch
Wire Harness
Wire Harness
Screw
Spillswitch
Switch Screw
Valve Bracket
Valve, Natural
Valve, Propane/LP
Pilot Assembly, Natural
Pilot Assembly, Propane/LP
Ignitor, Piezo
Bracket, Spill Switch
Burner, Natural
Burner, Propane/LP
Orifice, Natural
Orifice, Propane/LP
Brass Elbow
Brass Elbow
Flex Tubing
Air Deflector
Log Set
Rear Log
Front Log
Crossover Log
Log Piece
Screw
Screw
1
1
1
11
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
3
PARTS AVAILABLE - NOT SHOWN
GA6060
104529-01
M11084-26
106707
Lava Rock
Ember Material
Hex Screw for Blower Bracket
29
1
1
4
For more information, visit www.desatech.com
SBVRBN AND SBVRBP
CAST IRON STOVE AND BURNER SYSTEM
®
ILLUSTRATED
PARTS
BREAKDOWN
1L
AMITY™
SCIVFC(*) SERIES
PSCIVFC(*) SERIES
1C
1R
(* Indicates Color Suffix
Designation)
2
8
5
5
5
7-4
6
5
7-1
3
4
7-3
7-2
For more information, visit www.desatech.com
30
106707
OWNER’S MANUAL
PARTS LIST
This list contains replaceable parts used in your stove. When ordering parts, follow the instructions
listed under Replacement Parts on page 26 of this manual.
AMITY™
SCIVFC(*) SERIES
PSCIVFC(*) SERIES
(* Indicates Color Suffix Designation)
KEY
NO.
PART
NO.
1C
1L
1R
2
3
6
7
7-1
7-2
7-3
104171-08
104171-11
104171-12
104172-01
104173-01
104173-02
104173-03
104173-04
104173-05
104173-06
104173-07
104173-08
104173-09
104174-01
104175-01
104175-02
104175-03
104175-04
104175-05
104175-06
104175-07
104175-08
104175-09
104176-01
104177-01
*
*
*
7-4
8
*
104178-01
4
5
DESCRIPTION
QTY.
Top Grate with Screen, Center (Black Only)
Top Grate with Screen, Left (Black Only)
Top Grate with Screen, Right (Black Only)
Stove Back Panel (Black Only)
Bottom Door (Charcoal)
Bottom Door (Azure Blue)
Bottom Door (Hunter Green)
Bottom Door (Burgundy Red)
Bottom Door (Forest Green)
Bottom Door (Metallic Charcoal)
Bottom Door (Porcelain Enamel Red)
Bottom Door (Porcelain Enamel Teal Green)
Bottom Door (Porcelain Enamel Sand)
Stove Dropped Bottom
One Leg (Charcoal) (4 Total Per Stove)
One Leg (Azure Blue) (4 Total Per Stove)
One Leg (Hunter Green) (4 Total Per Stove)
One Leg (Burgundy Red) (4 Total Per Stove)
One Leg (Forest Green) (4 Total Per Stove)
One Leg (Metallic Charcoal) (4 Total Per Stove)
One Leg (Porcelain Enamel Red) (4 Total Per Stove)
One Leg (Porcelain Enamel Teal Green) (4 Total Per Stove)
One Leg (Porcelain Enamel Sand) (4 Total Per Stove)
Leg Leveler bolt M8 x 1.25 - 55mm Long (4 Total Per Stove)
Hardware Kit
Door Hinge Step Bolt With Shoulder (1 Per Unit)
Door Catch Bolt M8 x 1.25 - 55mm Long With Two M8 Hex Nuts (1 Per Unit)
Bottom Floor Bolts M6 x 1 - 25mm Long With Flat Washer
And Lock Washer (4 Per Unit)
Leg Bolts M6 x 1.25 - 20mm Long With Flat Washer And Lock Washer (4 Per Unit)
Back Panel Bolts M6 x 1 - 20mm Long With Flat Washer
And Lock Washer (6 Per Unit)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
PARTS AVAILABLE — NOT SHOWN
104108-01
104108-02
104108-03
104108-04
104108-05
104108-06
104807-01
104807-02
104807-03
Touch-up Spray Paint 12 oz Can (Charcoal)
Touch-up Spray Paint 12 oz Can (Azure Blue)
Touch-up Spray Paint 12 oz Can (Hunter Green)
Touch-up Spray Paint 12 oz Can (Burgundy Red)
Touch-up Spray Paint 12 oz Can (Forest Green)
Touch-up Spray Paint 12 oz Can (Metallic Charcoal)
Touch-up Paint Bottle with Brush (Porcelain Enamel Red)
Touch-up Paint Bottle with Brush (Porcelain Enamel Teal Green)
Touch-up Paint Bottle with Brush (Porcelain Enamel Sand)
1
1
1
1
1
1
1
1
1
* Included In Hardware Kit
106707
31
For more information, visit www.desatech.com
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written
warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTY
B-VENT BURNER SYSTEM AND AMITY™ STOVE CHASSIS
DESA International warrants this product to be free from defects in materials and components for four (4) years from the date of first
purchase, provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions.
To make a claim under this warranty the Bill of Sale or cancelled check must be presented.
This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater
to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST
be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts.
Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in accordance
with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become
damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost,
labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT;
THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE TO FOUR (4) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE;
AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND
DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential
damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
INTERNATIONAL
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
www.desatech.com
106707 01
NOT A UPC
106707-01
Rev. A
11/00
Download PDF
Similar pages
Freestanding gas Range
Freestanding gas Range
Free Standing Gas Stove
MGT8885X Spec Sheet
high heat shut off 2009
75040GM-M - Datatail
Propane Stove Maintenance
Electrolux Ew30gf65gs Quick Specs
OWNER`S MANUAL