BV-200R Bravo 2 Motion Detector

BV-200R Bravo 2 Motion Detector
Series
BV-200R
Security Products
Motion Detector
INSTALLATION INSTRUCTIONS
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
WALL-TO-WALL LENS
SPECIFICATIONS
TM
∗
Multi-Level Signal Processing
Dual element low noise sensor
Four interchangeable lenses
High level static protection
High level transient protection
High level white light immunity
Excellent RF immunity
Temperature compensation
Fast / slow detection jumper
LED on / off jumper
Vertical adjustment
SMD construction
Super quiet operation
Wall / corner mounting
Small size
Blends with any decor
5 YEAR WARRANTY
INTRODUCTION
The Bravo 2 is a general purpose PIR designed to provide
reliable motion detection for residential and commercial
applications.
Exceptional design care and factory testing ensure years
of trouble free performance. Immunity against false alarms
from RF, static, electrical transient and white light are all
designed in features.
∗
Multi-Level Signal Processing , temperature compensation
and large multi-beam lens design means the human target
will not slip by unnoticed even on a hot summer day.
Four interchangeable lenses, wall or corner mounting and
vertical adjustment provide application versatility, and
your client will appreciate the small size and elegant
simplicity of the case design.
Our Bravo 2 with its 5 year warranty is your assurance of a
trouble free installation.
∗ Protected by one or more of the following patents:
Canada 2099971, US 5444432
Operating voltage ................................... 9.5VDC-14.5VDC
Supply voltage ripple .......................... 3.0V pp @ 12VDC
Standby current ..................................... less than 16mA
Current in alarm ..................................... less than 20mA
Contact rating (alarm & tamper) ............ 100mA @ 24VDC
Alarm contact resistor in common ............ 10 ohm 1/4W
Operating temperature : .............................. 0°C to 50°C
Storage temperature : .............................. -40°C to 60°C
Operating humidity ................ 5% to 95% RH non-cond.
Storage humidity .................... up to 99% RH non cond.
RF immunity ......... 50 V/m over range 0.01MHz-1.2GHz
Static immunity ....................................................... 25kV
Transient immunity ........................... 2.4kV @ 1.2 joules
White light immunity ............ 20,000 Lux at the detector
Walk detection speed ............................... 0.15m-3.0m/s
Coverage angle (wall/wall lens) ................ 90° minimum
Vertical adjustment ....................................... +5° to -10°
Mounting heights ................ 2m to 3.0m (nominal 2.3m)
1.2m to 1.5m (pet alley only)
TOP VIEW
L2
9.1 m
L3
4.6 m
L4
0 m
4.6 m
9.1 m
0 m
3.0 m
6.1 m
9.1 m
SIDE VIEW
13.0 m
13.0 m
CORRIDOR LENS
TOP VIEW
COVERAGE
Wall-to-Wall lens
Corridor lens
Curtain lens
Pet Alley lens
(BV-L1) ..... 13m × 13m
(BV-L2) ..... 22m × 2m
(BV-L3) ..... 13m × 1m
(BV-L4) ..... 13m ×13m
2.0 m
BEAM PATTERN CHART
ILLUSTRATES THE CENTRE
LINE OF EACH BEAM PAIR
PHYSICAL
Dimensions: 89 mm × 64 mm × 48 mm
Colour: White case with light gray lens
Shipping Weight: 190 g
Models: BV-200R Form A alarm contact & tamper switch
CENTRE
LINE
22.0 m
MOUNTING HEIGHT CHART
HEIGHT
m
SIDE VIEW
SETTING FOR FULL RANGE
WALL/WALL CORRIDOR
CURTAIN
3 m
0.00
-0.25
0.00
2.4 m
+0.50
+0.25
0.00
2.1 m
+0.75
+0.25
0.00
1.8 m
+1.00
+0.50
0.00
22.0 m
PET ALLEY
CURTAIN LENS
SIDE VIEW
1.5 m
0.00
1.2 m
0.00
TOP VIEW
13.0 m
13.0 m
LOCATING THE DETECTOR
Select a detector location that will provide the coverage
required keeping in mind the following potential problems:
Reflective Surfaces: Do not aim the detector at
reflective surfaces such as mirrors or windows as this
may distort the coverage pattern or reflect sunlight
directly onto the detector.
Air Flow: Avoid locations that are subject to direct high
air flow such as near an air duct outlet.
Moisture: Do not locate the detector near sources of
steam or oil.
The Sun: Do not aim the detector such that it will
receive direct or reflected (mirror) sunlight,
Pets: If there are pets on the premises, use the pet
alley lens.
Obstructions: Do not limit the coverage by large
objects within the detection area such as plants or
filing cabinets.
MOUNTING
To open the case, use a small flat blade screwdriver and
gently push in the tab at the bottom of the case and pull the
cover straight out at the bottom. Loosen the PCB screw,
and push the board up as far as it will go. Using a small
screwdriver, remove the appropriate knockouts for the
mounting screws. Remove the left and/or right wiring
entrance knockouts located at the top of the backplate.
Mount the backplate using the screws supplied.
VERTICAL ADJUSTMENT
NOTE: Range and dead zones may vary due to settings.
Using the Mounting Height Chart, set the vertical
adjustment to get the desired coverage. Ensure that the
PCB retaining screw is tightened just enough to prevent
board movement.
Moving the circuit board DOWN will increase the far range
and move the near beams farther out from the mounting
wall. Moving the circuit board UP will reduce the far range
and bring the near beams closer to the mounting wall.
Moving the circuit board DOWN too far will cause the far
beams to “look” above the target as a result, the range may
appear shorter.
JUMPER J1 will enable/disable the alarm LED. If J1 is OFF,
the LED will not operate on alarm. If J1 is ON the LED will
operate on alarm.
JUMPER J2 selects between “FAST” and “SLOW” operation.
For a typical environment, the unit should be set on “FAST”
(J2 ON). If the environment presents potential disturbances
that cannot be avoided, set J2 to OFF for “SLOW” operation.
NOTE: The corridor lens should not be used in a
corridor that is less than 1.8 m. Ensure the beams are
aimed directly down the centre of corridor. With the
corridor lens, set J2 to “FAST”.
CHANGING LENSES
The Bravo 2 is supplied with the “wall-to-wall” lens. To
change the lens, release the top tab and pull the lens
holder out. This action releases the lens. Insert the lens
with the GROOVES FACING INWARD. The bottom of the
lens is indicated by two triangular indentations. Ensure
that the lens is centred left to right then reinstall the lens
holder. The lens holder will snap into place sealing the
lens into position.
WIRING
CONTROL PANEL
TAMPER POWER
ALARM
EOLR
TAMP 12V GND
LED NO NC C
Lim ited W arranty
10Ω
0.25W
POWER
20 mA
12 VDC
TAMPER
CONTACT
100 mA
24 VDC
Contacts shown
with power applied
and no alarm.
ALARM
CONTACTS
100 mA
24 VDC
WALK TESTING
Once the detector has been set up, walk test the entire area
where coverage is desired. Should the coverage be
incomplete, readjust or relocate the detector to obtain full
coverage. Once coverage is as required, the alarm LED
may be disabled by setting J1 to OFF.
IMPORTANT NOTE: Upon installation, the unit should
be thoroughly tested to verify proper operation. The
end user should be instructed on how to perform walk
tests, and should walk test the detector regularly.
DM-C and DM-W Detector Mounting Brackets
Use the optional DM-W Wall Mount and DM-C Ceiling
Mount brackets to solve difficult placement problems. The
DM-W and DM-C mount to the wall or ceiling and allow full
vertical and horizontal positioning of the motion detector;
the detector can be tilted up or down and rotated through
90° to obtain the best position for optimal coverage. The
Bravo has been designed to be fully compatible with the
DM-W and DM-C brackets. Contact your DSC distributor
for more information.
Digital Security Controls Ltd. warrants that for a period of five years from the date of
purchase, the product shall be free of defects in materials and workmanship under normal use
and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at
its option, repair or replace the defective equipment upon return of the equipment to its repair
depot. This warranty applies only to defects in parts and workmanship and not to damage
incurred in shipping or handling, or damage due to causes beyond the control of Digital
Security Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage,
or damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any
and all other warranties, whether expressed or implied and of all other obligations or liabilities on
the part of Digital Security Controls Ltd. Digital Security Controls Ltd. neither assumes, nor
authorizes any other person purporting to act on its behalf to modify or to change this warranty,
nor to assume for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential
damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in
connection with the purchase, installation or operation or failure of this product.
Motion detectors can only detect motion within the designated areas as shown in their
respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. They have
multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings,
floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether
intentional or unintentional such as masking, painting, or spraying of any material on the
lenses, mirrors, windows or any other part of the detection system will impair its proper
operation.
Passive infrared motion detectors operate by sensing changes in temperature. However
their effectiveness can be reduced when the ambient temperature rises near or above body
temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.
Warning: Digital Security Controls Ltd. recommends that the entire system be completely
tested on a regular basis. However, despite frequent testing, and due to, but not limited to,
criminal tampering or electrical disruption, it is possible for this product to fail to perform
as expected.
Important Information: Changes or modifications not expressly approved by Digital
Security Controls Ltd. could void the user’s authority to operate this equipment.
TM
Security Products
© 1997 Digital Security Controls Ltd.
1645 Flint Road, Downsview, Ontario, Canada M3J 2J6
(416) 665-8460 Fax:(416) 665-7498
29002527 R0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising