Cypress Technology CVW-11HS LCD video wall control system Operation Manual

CVW-11HS
LCD Multi-Screen Video
Wall Control System
Operation Manual
CVW-11HS
Disclaimers
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes
no commitment to update or to keep current the information
contained in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
Copyright Notice
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means
- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.0 January 2011
Trademark Acknowledgments
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
Safety Precautions
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:







Always follow basic safety precautions to reduce the risk of
fire, electrical shock and injury to persons.
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
Do not attach the power supply cabling to building surfaces.
Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.
Revision History
Version No
RDV01
RDV02
RDV03
RDV04
Date
20110119
20110317
20110324
20110719
Summary of Change
Preliminary Release
Add New OSD Menu
Change OSD Figures
Add TV Option
Table of Contents
1.
Introduction ……………………..……………………...…........….…….
1
2.
Applications …………………..………………….……...................…..
1
3.
Package Contents ………………………...........……….................…
1
4.
System Requirements ……………..……….........………............…….
1
5.
Features …………………………………………......……........…...……
2
6.
Specifications ………………………………...……..........………....….
3
7.
Operation Controls and Functions ……………...……..............……
7.1 Front Panel ..............................................................................
4
7.2
Rear Panel .…………………………………..…….......…...….…
4
7.3
OSD Menu .…………………………………..…….......…...….…
5
8.
Remote Control .......................…......……………..........…..…....…...
6
9.
RS-232 Protocol ................................................................................
7
9.1
Pin Definition .............................................................................
7
9.2
Command ...............................................................................
7
10.
Connection and Installation ….………………….........…..…..…......
8
11.
Acronyms …......................................................................................
9
4
1. Introduction
To capture the public’s attention, the Multi-Screen Video Wall control system
is ideal for advertising, entertaining and displaying information. The device
allows users to display HDMI or PC sources to multiple LCD monitors, while
thanks to the built-in RS-232 you are able to fully customize the LCD panels
giving you complete control over 2x2, 3x3, 4x4 and 5x5 video walls. This
device is also embedded with a PC to HDMI scaler, which allows the input
PC video signal to be integrated and converted to digital HDMI signal output
to the video wall. There is a pair of additional L/R RCA connecters for user to
output analog audio (extracted from the HDMI source, or routed from the
analog audio input) to local speakers. Further, the IR remote and the RS-232
control free users with on hand control from anywhere they wish.
2. Applications
TV wall
Video wall
Display wall
Gaming wall
Movie wall
Combination advertising wall
3. Package Contents
Video wall control system(s)
IR remote control x 1
IR blaster x 1
RS-232 cable(s)
RS-232 level-shift board (optional)
5V DC power adaptor(s)
Operation Manual
4. System Requirements
HDMI or PC splitter/matrix with input source signal and connection cables,
display TV/monitor with connection cables.
1
5. Features
Supports 6 or more video wall combinations of HxV: 2x2(four monitors),
3x2(sis monitors), 3x3(nine monitors), 4x3(12 monitors),4x4(16 monitors)
and 5x5 (25 monitors)
Supports both HDMI and PC (with audio) input sources
Resolution support up to 1080p full HD
Use RS-232 cables to cascade over every connected CVW-11HS boxes to
remotely control each monitors with one setting only.
Supports external IR receiver for IR remote control
Note: Requires HDMI or PC (with audio) signal splitter to distribute vide /
audio signal to each connected CVW-11HS box.
2
6. Specifications
Input Ports
1xHDMI, 1xPC, 1xRS-232 (female jack), 1xIR,
1xL/R (3.5Ø phone jack)
Output Ports
1xHDMI, 1xRS-232 (male jack), 1xL/R (RCA jack)
IR Frequency
38Hz
IR Cable Length
3M
Input Resolution Supports PC: VGA ~ SXGA
HDMI: 48op~1080p
Output Resolution
HDMI: 720p & 1080p
Supports
Audio Format
PCM 2Ch
Power Supply
5V/3.6A DC (US/EU standards, CE/FCC/UL Certified)
ESD Protection
Human body model: ± 8kV (air-gap discharge)
± 4kV (contact discharge)
Dimension (mm)
200 (W) x 155 (D) x 45(H)
Weight (g)
815
Chassis Material
Aluminum
Silkscreen Color
Black
Operating Temperature
0˚C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature
-20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity
20 ~ 90% RH (Non-condensing)
Power Consumption (W) 15.5
3
7. Operation Controls and Functions
7.1 Front Panel
HDMI IN
AUDIO IN
PC IN
RS 232 IN
RS 232 OUT
IR IN
③
④
⑤
⑥
CVW-11HS Video Wall Processor
①
②
① HDMI IN: This slot is to connect from HDMI splitter or matrix with input
source signal.
② Audio IN: This slot is to connect with the audio signal from the source
equipment with 3.5Ø phone jack.
③ PC IN: This slot is to connect from PC/RGB splitter or matrix with input
source signal.
④ RS-232 IN: As a first device of the video wall system, this slot is to connect
with PC/NB equipment for RS-232 control. Starting from the second device
of the video wall system this slot should be connect from the RS-232 out of
the last device.
Note: For RS-232 control it required a special level-shift board and it is an
optional accessory selection.
⑤ RS-232 OUT: This slot is to connect to the next video wall control system’s
RS-232 IN.
⑥ IR IN: This slot is to connect with IR blaster included in the package for
receiving the IR signal of the device’ remote controller.
7.2 Rear Panel
L
HDMI OUT
DC 5V
R
AUDIO OUT
①
②
③
① DC 5V: Connect this slot with power adaptor included in the package
from the AC wall outlet. When the power is plugged on the device will
automatically power ON.
② Audio OUT L/F: These slots are to connect with RCA jack cables to the
active speaker or to display’s audio input.
③ HDMI OUT: This slot is to connect to the display with HDMI input.
4
7.3 OSD Menu
PICTURE
MENU*1
MAIN MENU
STANDARD
ON/OFF
R OFFSET
0~255 (118)
G OFFSET
0~255 (116)
B OFFSET
0~255 (118)
R GAIN
0~255 (098)
G GAIN
0~255 (098)
B GAIN
0~255 (098)
CONTRAST
0~63 (50)
BRIGHTNESS
0~63 (40)
LANGUAGE
ENG / T.CHINESE (ENG)
HDMI SOUND
ON/OFF (ON)
STANDARD
ON/OFF (OFF)
H POSITION START 000~385 (*2)
SETUP MENU*1
V POSITION START 000~53 (*2)
H ZOOM SIZE
000~255 (0)
V ZOOM SIZE
000~255 (0)
TV Option Width
1~10 (1)
TV Option Height 1~10 (1)
*NOTE: 1. The Picture Menu allows users to adjust single monitor’s setting while
the Setup Menu will only needs to be adjust once and all monitors
will be automatically adjusted.
2. Defual value will adjusted automatically depending the the input
signal's timing.
Picture Standard: Set it to ON will allow system to set the picture menu
into the default value as indicated in the ( ).
Picture R/G/B Offset: These functions are to set the single picture's R/G/B
brightness.
Picture R/G/B Gain: These functions are to increase or decrease the color of
single picture's R/G/B.
Picture Contrast: This function is to set the single picture's color contrast.
Picture Brightness: This function is to set the single picutre's brightness.
Setup Language: There are two language available in the OSD and they are
English and Traditional Chinese.
Setup HDMI Sound: This function is to set the HDMI output audio sound to be
ON or OFF.
Setup Standard: Set it to ON will allow system to set the setup menu into the
default value as indicated in the ( ).
5
Setup H/V Position Start: These functions are to set the total value of the
vertical and horizontal value of the TV wall.
Setup H/V Zoom Size: These functions are to set the total value of the vertical
and horizontal zoom in and zoom out size of the TV wall.
Setup H/V Blanking Edit: These functions are to set the total value of the
vertical and horizontal value of the blanking area of
the TV wall.
Setup TV Option Width: This function is to set the numbers of the TV/display
that is to be on a horizontal line of the TV wall.
Setup TV Option Height: This function is to set the numbers of the TV/display
that is to be on a vertical line of the TV wall.
8. Remote Control
① Power: Press this button to switch on the
device(s). All the connected Video wall system
control device(s) will be switch to ON.
② Power OFF: Press this button to switch off the
POWER OFF
POWER
device. All the connected Video wall system
①
②
SINGLE
control device(s) will be switch to OFF.
③
③ SINGLE: Press this button to set the image
2X2
3X3
4X4
to be displayed on each and every connected
3X2
4x3
5x5
TV/monitor identically.
④
④ FULL: There are 6 options of setting an image
FULL
to be displayed on TV/ monitor and they are
2x2, 3x3, 4x4, 3x2, 4x3 and 5x5.
⑤ pqtu&OK: Press the arrow buttons to select
and adjust the selection in the OSD menu and
OK
⑤
value or to select the display. Press OK to
RETURN
MENU
⑦
⑥
confirm the selection.
HDMI
VGA
U/OVER
⑧
⑥ MENU: Press this button to enter into the OSD
⑩
⑨
720P
OPTION 1080P
menu. When the setting is selected and
⑪
⑬
⑫
confirmed all the output display will
automatically changed to the selected settings.
⑦ RETURN: Press this button to return to the last
layer of OSD selection or to exit the OSD.
CR-98
⑧ HDMI: Press this hot key to select the input source
from HDMI IN.
⑨ VGA: Press this hot key to select the input source
from PC IN.
⑩ U/OVER: Press this key to adjust the screen when the image is overscan or
underscan.
⑪ 720P: Press this hot key to switch the output timing to 720p
⑫ OPTION: Press this key to switch to the special setting of the display image
set by the factory design.
⑬ 1080P: Press this hot key to switch the output timing to 1080p
*Function that automatically adjust all monitors in once.
6
9. RS-232 Protocol
9.1 Pin Definition
RS-232 IN
RS-232 OUT
Pin 1
NC
Pin 1
NC
Pin 2
TxD
Pin 2
RxD
Pin 3
RxD
Pin 3
TxD
Pin 4
NC
Pin 4
NC
Pin 5
GND
Pin 5
GND
Pin 6
NC
Pin 6
NC
Pin 7
Connect to Pin 8
Pin 7
Connect to Pin 8
Pin 8
Connect to Pin 7
Pin 8
Connect to Pin 7
Pin 9
NC
Pin 9
NC
Baud Rate: 19200bps
Data bit: 8 bits
Parity: None
Stop Bit: 1 bit
Flow Control: None
9.2 Command
COMMAND
ACTION
0x23 0x53 0x30 0x30 0x31 0x23
POWER ON
0x23 0x53 0x30 0x30 0x30 0x23
POWER OFF
0x23 0x43 0x30 0x30 0x30 0x23
UNDER SCAN
0x23 0x43 0x30 0x30 0x31 0x23
OVER SCAN
0x23 0x43 0x52 0x11 0x00 0x23
SINGLE
0x23 0x43 0x52 0x11 0x00 0x23
2x2
0x23 0x43 0x52 0x11 0x00 0x23
3x3
0x23 0x43 0x52 0x11 0x00 0x23
4x4
0x23 0x43 0x52 0x11 0x00 0x23
5x5
0x23 0x43 0x52 0x11 0x00 0x23
3x2
0x23 0x43 0x52 0x11 0x00 0x23
4x3
0xEF 0x05 0xD7 0xC0 0x22 0x07 0xEE
Change to HDMI
0xEF 0x05 0xD0 0xC0 0x22 0x00 0xEE
Change to PC
0xEF 0x06 0x8A 0xC0 0x20 0x01 0xBB 0xEE Option
7
10. Connection and Installation
1. Connect the HDMI source (such as DVD or PS3) into the “HDMI IN” of
the HDMI splitter and connect the “HDMI OUT” from the splitter to Video
Wall control systems (CVW-11HS) respectively. Connect each Control
system HDMI output port to each LCD monitor’s HDMI input port. The
display sequence should be from top left to right and from second right to
left. For more details please refers to the diagram.
2. IR receiver must connect to the first Video Wall control system IR input port.
Meanwhile, connect the first RS-232 output port to second system of RS-232
input port and vise verse. (The upper left will be the first LCD monitor of the
connection diagram above).
SINGLE
FULL
䡾
䡿
䡾
䡿
䢁
䢀
䢁
䢀
䡾
䡿
䢀
䢁
HDMI
HDMI
HDMI
HDMI
HDMI
HDMI
HDMI
HDMI
IR!Cable
HDMI Splitter
HDMI
3M
30°
3M
30°
7M
or
DVD
PS3
NOTE: Display sequence is from top left to right and from second right to
left and so on sequence.
8
A
Acronyms
Acronym
Complete Term
HDMI
High-Definition Multimedia Interface
9
CYPRESS TECHNOLOGY CO., LTD.
Home page: http://www.cypress.com.tw
20110126 MPM-CVW11HS
">