GFDS260GF/265GF GE 8.1 cu. ft. capacity Front Load gas dryer with steam "

GFDS260GF/265GF GE 8.1 cu. ft. capacity Front Load gas dryer with steam "
GFDS260GF/265GF
52"
25-3/8"
GE® 8.1 cu. ft. capacity Front Load gas dryer with steam
4-5/8"
Dimensions and Installation Information (in inches)
Gas Dryer Rating
120V
60Hz, 8A, 850W
Exhaust Options: 3-way via rear, left, and bottom.
Circuit Requirements: An individual, properly grounded
branch circuit, protected by a 15-20 amp circuit breaker
or a time-delay fuse, is required.
Note: Dryer wall outlet must be located within 36”
of service cord entry and accessible when dryer is
mounted in position.
Installation Information: For complete information, see
installation instructions packed with your dryer.
28
34-3/8
2-1/4"
39-2/5
3-5/8
For answers to your Monogram,® Cafe™ Series
or Profile™ Series appliance questions, visit
our website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
5-7/8
Specification Revised 4/15
GFDS260GF/265GF
Stacked Dimensions (in inches)
GE® 8.1 cu. ft. capacity Front Load gas dryer with steam
Special Installation Requirements:
Stacked Installation:
Brackets for stacking dryer over washer are not included
with the washer.
Order part no. GEFLSTACK or part no. WE25X10018.
Alcove or Closet Installation:
•If your dryer is approved for installation in an alcove or closet, it
will be stated on a label on the dryer back.
79-5/8
C
•The dryer MUST be exhausted to the outside.
•Minimum clearances between dryer cabinet and adjacent walls
or other surfaces are: 0" either side, 3" front and rear
•Minimum vertical space from floor to overhead cabinets,
ceilings, etc. is 52".
5-3/8
1-5/8
11-5/8
3-5/8
•Closet doors must be louvered or otherwise ventilated and must
contain a minimum of 60 sq. in. of open area equally distributed.
If this closet contains both a washer and a dryer, doors
must contain a minimum of 120 sq. in. of open area equally
distributed.
•No other fuel-burning appliance shall be installed in the same
closet with a gas dryer.
Pedestal Dimensions (in inches)
Bathroom or Bedroom Installation:
•The dryer MUST be exhausted to the outdoors.
This optional 13" pedestal raises
the door opening and height of
the washer or dryer.
•The installation must conform with the local codes, or in the
absence of local codes, with the National Electric Code and
National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearance other than Alcove or Closet Installations:
•Minimum clearances to combustible surfaces 0" both sides,
3" rear.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
For answers to your Monogram,® Cafe™ Series
or Profile™ Series appliance questions, visit
our website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
GFXP1308F
27-7/8
13
29-3/4
Specification Revised 4/15
GFDS260GF/265GF
GE® 8.1 cu. ft. capacity Front Load gas dryer with steam
Dryer exhausting information—use metal
duct only vertical and horizontal ducting
Best performance
Maximum length
of 4" dia rigid
A 4
metal duct
B
A
Exhaust hood type
Number
A
B
4
2-1/2
of 90°
4"
2-1/2"
B
turns opening opening
Domestic dryer models
0
200 ft.
175 ft.
2-1/2
1
185 ft.
165 ft.
2
175 ft.
155 ft.
3
165 ft.
145 ft.
GE Frontload Long Vent 7.0
4
155 ft.
135 ft.
cu. ft. capacity electric dryer
(GFDL)
5
145 ft.
125 ft.
0
150 ft.
125 ft.
1
135 ft.
115 ft.
2
125 ft.
105 ft.
3
115 ft.
95 ft.
Long Vent 6.0 - 8.0 cu. ft.
4
105
ft.
85
ft.
capacity electric & gas dryers
(GTDL and GTV)
5
95 ft.
75 ft.
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2
85 ft.
65 ft.
3
70 ft.
55 ft.
Long Vent 7.0 cu. ft. capacity
4
60 ft.
45 ft.
electric & gas (GTD42, GTD45,
GTD65, GTX42 and GTX60)
5
55 ft.
35 ft.
0
90 ft.
60 ft.
All 6.0 - 8.3 cu. ft. capacity
1
60 ft.
45 ft.
models electric and gas dryers
2
45 ft.
35 ft.
(GFDS, GFDR, GFDN, GTDS,
3
35
ft.
25
ft.
GTDN, GHDN, GHDS, GTDP,
GLDP, GTD, HTDP, HTDX)
4
25 ft.
15 ft.
0
90 ft.
60 ft.
1
60 ft.
45 ft.
2
45 ft.
35 ft.
DCVH480
3
35 ft.
25 ft.
0
46 ft.
37 ft.
1
37 ft.
30 ft.
2
30 ft.
22 ft.
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
3
23 ft.
15 ft.
0
56 ft.
42 ft.
1
48 ft.
34 ft.
2
40 ft.
26 ft.
Laundry Center GUD27
3
32 ft.
18 ft.
0
43 ft.
36 ft.
1
33 ft.
26 ft.
Laundry Center GUD24
2
24 ft.
16 ft.
A
Dryer Exhausting Information – Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4”
diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then
UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special
installations, it may be necessary to connect the dryer to the house vent using a
flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used
ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot
be used AND where a 4” diameter can be maintained throughout the entire length
of the transition duct. Please see installation instruction packed with your dryer for
complete instructions when using flexible metal (foil type) ducting.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to
the side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be
tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should
be treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any
enclosed house floor (crawl space), or into an attic, since the accumulated lint could
create a fire hazard or moisture could cause damage. Never terminate the exhaust
into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,
bird nesting, etc. The wall cap must also be located at least 12" above the ground or
any other obstruction with the opening pointed down.
For more information on venting kits and accessories, please call
1-800-GE-CARES.
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
The total vent system length includes all the straight portions and elbows of
the system (transition duct included).
Specification Revised 4/15
GFDS260GF/265GF
GE® 8.1 cu. ft. capacity Front Load gas dryer with steam
Features and Benefits
• Detangle Assist - Twisted sheets and comforters are a thing of the
past with a setting that pauses and reverses direction to separate
items and reduce wrinkling
• Steam Refresh - Rejuvenate lightly worn clothes by getting rid of
wrinkles and odors with this convenient setting using the power
of steam
• Steam Dewrinkle - Stored or wrinkled clothes come out wrinkle-free
with the helpful setting that uses steam to refresh and dry a load
of any size
• Stainless steel drum - Resists rust and helps protect clothes
• HE Sensor Dry - Keep your clothes looking and feeling their best.
Dual thermistors continually monitor temperature with a sensor bar
that measures moisture to prevent over-drying
• Model GFDS260GFWW – White
• Model GFDS265GFMC – Metallic Carbon
• Model GFDS265GFRR – Ruby Red
Specification Revised 4/15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement