LEVITON UPB™ 8-BUTTON HOUSE CONTROLLER Cat.No.38A00-2 Installation Instructions and User’s Guide DI-022-HL382-05AAR2243 (38I00-2) INSTALLATION WARNINGS AND CAUTIONS • TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring! • Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations. • Ifyouareunsureaboutanypartoftheseinstructions,consultanelectrician. ENGLISH WARNINGS AND CAUTIONS • Usethisdevicewithcopper or copper-clad wire only. • Forindooruseonly. • SAVETHESEINSTRUCTIONS. Figure 1 - Leviton UPB™ 6-Button Scene Switch Leviton UPB™ 8-Button House Controller Overview TheLevitonUPB™8-ButtonHouseController(Figure1)isusedtoturnonorofflightinginupto8roomsinahousewhereLeviton UPB™ Wall Switches and Leviton UPB™ 6-Button Room Controllers have been installed. It can also be used for various other lighting controlapplications,suchascontrolling8individualloadsorlightingscenes(on/off).ItusestheUPB™two-waypowerlinecommunication technology to communicate with an Leviton controller, UPB™ Wall Switches, and other UPB™ devices on the network. 1 2 3 4 TheLevitonUPB™8-ButtonHouseControllerhaseightpushbuttonslabeled1,2,3,4,5,6,7,and8(althoughthesebuttonsmaybe custom engraved). Each pushbutton is slightly backlit so that the buttons can be seen in a dark room. Depending on configuration of the Leviton UPB™ 8-Button House Controller, one or more of the eight pushbuttons will be distinctly illuminated, indicating that one or more lights are on in the respective room(s). If a pushbutton is not illuminated, that means all lights in the respective room are currently off. 5 6 7 8 Changing Switch Color The color of the Leviton UPB™ 8-Button House Controller may be changed to complement the interior décor. The Leviton UPB™ 8-Button House Controller is supplied with a white bezel. Additional colors are available; contact your Leviton distributor for more information. When changing the bezel, make sure that the Leviton UPB™ 8-Button House Controller is disconnected from all power, and proceed as follows: Figure 2 – Changing Switch Color 1. The bezel attaches to the Leviton UPB™ 6-Button Scene Switch with two small Philips head screws: one on the upperright corner and one on the lower-left corner (Figure 2). 2. Using a small-bladed Philips screwdriver, unscrew each of the two screws. Remove the bezel from the back housing. 3. Install the new bezel by aligning the mounting holes on the bezel with the installation pins on the back housing. Secure bezel to back housing with the two Phillips screws that were removed in Step 1. INSTALLATION INSTRUCTIONS 1. TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring! 2. If applicable, remove the faceplate from the existing device, remove the existing device from the wall box, and disconnect the wires fromtheexistingdevice.Identifythe"Line"(black)and"Neutral"(white)wires. 3. Remove3/4"ofinsulationfromeachofthewiresontheLevitonUPB™8-ButtonHouseController.InstalltheLevitonUPB™8-Button House Controller by connecting wires per wiring configuration shown in Figure 3. 4. After all connections have been made, be certain that all wire connectors are firmly attached and there is no exposed copper. 5. GentlyplacethewiresandLevitonUPB™8-ButtonHouseControllerintothewallboxwiththeONpushbuttonatthetopofdevice. Using the supplied screws, attach the Leviton UPB™ 8-Button House Controller to the wall box. Figure 3 – Wiring Diagram MAIN CIRCUIT BREAKER PANEL 1 2 38A00-2 8-BUTTON HOUSE CONTROLLER 3 4 6. Before installing the faceplate, restore power to the circuit for testing. 5 6 7. After testing the Leviton UPB™ 8-Button House Controller for proper local operation, install a Decora® faceplate over the Leviton UPB™ 8-Button House Controller. 7 8 BLACK The Leviton UPB™ 8-Button House Controller is designed to control up to 8 rooms of lighting using Leviton Lighting Control (HLC) but also has several configuration options that can be enabled or modified using the UPB™ UPStart configuration software. WHITE 120VAC 60Hz NEUTRAL LINE WEB VERSION CONFIGURING THE Leviton UPB™ 8-BUTTON HOUSE CONTROLLER Option Factory Default Leviton Lighting Control (HLC) Pushbuttons1-8 SupperToggle/Link013–Link020,respectively Each pushbutton on the Leviton UPB™ 8-Button House Controller will toggle the lighting loads in the respective room on and off. Pushbuttons1-8LED Indicators Each LED Indicator is assigned to its pushbutton’s Link ID When the room is turned on using the pushbutton, the LED indicator under the respective pushbutton is illuminated. When the room is turned off using the pushbutton, the LED indicator under the respective pushbutton is turned off. Anytime a lighting load in a room is turned on, the LED indicator under the respective pushbutton (room) is illuminated. When all loads in a room are turned off, the LED indicator under the respective pushbutton (room) is turned off. Each LED Indicator is independent (multiple LED indicators may be on at one time). UPB Transmission Attempts 2 Nochange. UPB ID NID=255 UID=096 LevitoncontrollerconfiguresNetworkID(NID),UnitID(UID),NetworkPassword, NetworkName,RoomName,DeviceName,etc. LED Brightness High Nochange. LED Backlighting Enabled Nochange. Leviton UPB™ 8-BUTTON HOUSE CONTROLLER OPERATION The Leviton UPB™ 8-Button House Controller has many configurable items that can be set using the UPB™ UPStart configuration software. The following describes the operation of the Leviton UPB™ 8-Button House Controller in its factory default configuration. Using Pushbuttons to Control Individual Lighting Loads In its factory default configuration, all 8 pushbuttons are configured to toggle between two different actions each time a pushbutton is pressed. Likewise the LED indicator behind the pushbutton will toggle when the pushbutton is pressed. Linking Pushbuttons to Leviton UPB™ Wall Switch Dimmer(s) To configure these actions, the pushbuttons on the Leviton UPB™ 8-Button House Controller must be linked to Leviton UPB™ Wall Switch Dimmer(s) as follows: Step Operation 1 Use the local rocker switch on the Leviton UPB™ Wall Switch Dimmer(s) to set the desired level(s). 2 TaptherockerswitchontheLevitonUPB™WallSwitchDimmer(s)five(5)timesquickly. 3 The Leviton UPB™ Wall Switch Dimmer will flash its lighting load one time and blink its LED blue, to indicate that it is ready to be linked. 4 PressthepushbuttonontheLevitonUPB™8-ButtonHouseControllerfive(5)timesquickly. 5 Each Leviton UPB™ Wall Switch will flash its lighting load one time to indicate that it is successfully linked to the pushbutton and that the new light level has been set. Unlinking Pushbuttons from Leviton UPB™ Wall Switch Dimmer(s) If you accidentally link the wrong pushbutton to the wrong Leviton UPB™ Wall Switch Dimmer, you can unlink them as follows: Step Operation 1 TaptherockerswitchonthedesiredLevitonUPB™WallSwitchDimmer(s)five(5)timesquickly. 2 The Leviton UPB™ Wall Switch Dimmer will flash its lighting load one time and blink its LED blue, to indicate that it is ready to be unlinked. 3 PressthepushbuttonontheLevitonUPB™8-ButtonHouseControllerten(10)timesquickly. 4 Each Leviton UPB™ Wall Switch will flash its lighting load one time to indicate that it is successfully unlinked. Toggling Lighting Loads After the pushbuttons have been linked, when a pushbutton is pressed while its LED indicator is off, the lighting loads are set to the preset lighting levels and the LED indicator is turned on. When the pushbutton is pressed again (while its LED indicator is on), the lighting loads are turn off and the LED indicator is turned off. Event When LED Indicator is Off When LED Indicator is On Single-Tap The Leviton UPB™ Wall Switch Dimmer(s) that are linked to this pushbutton will go to their preset lighting levels. The LED indicator under the pushbutton is turned on. The Leviton UPB™ Wall Switch Dimmer(s) that are linked to this pushbutton will fade to 0% (off). The LED indicator under the pushbutton is turned off. DoubleTap The Leviton UPB™ Wall Switch Dimmer(s) that are linked tothispushbuttonwillsnapto100%(on). The LED indicator under the pushbutton is turned on. The Leviton UPB™ Wall Switch Dimmer(s) that are linked to this pushbutton will snap to 0% (off). The LED indicator under the pushbutton is turned off. Brightening and Dimming Lighting Loads When a pushbutton is pressed and held while its LED indicator is off, the lights are brightened, until the pushbutton is released. When the pushbutton is pressed, the lights are dimmed, until the pushbutton is released. Event When LED Indicator is Off When LED Indicator is On Hold The Leviton UPB™ Wall Switch Dimmer(s) that are linked to this pushbutton will brighten. The LED indicator under the pushbutton is turned on. The Leviton UPB™ Wall Switch Dimmer(s) that are linked to this pushbutton will dim. The LED indicator under the pushbutton is turned off. Release The Leviton UPB™ Wall Switch Dimmer(s) that are linked to this pushbutton will stop brightening. The Leviton UPB™ Wall Switch Dimmer(s) that are linked to this pushbutton will stop dimming. SPECIFICATIONS Model Number Step Operation 1 Pressandholdthe"1"and"8"pushbuttonssimultaneouslyforatleast3seconds. NumberofBacklit Pushbuttons 2 AlloftheLEDindicatorswillblinktoindicatethattheLevitonUPB™8-ButtonHouseControllerisinSetupMode. Connections Reset to Factory Default Settings To reset the Leviton UPB™ 8-Button House Controller to factory default settings: Step Operation 1 Pressandholdthe"1"and"8"pushbuttonssimultaneouslyforatleast3seconds. 2 AlloftheLEDindicatorswillblinktoindicatethattheLevitonUPB™8-ButtonHouseControllerisinSetupMode. 3 Pressandholdthe"2"and"7"pushbuttonssimultaneouslyforatleast3seconds. 4 TheLEDindicatorswillstopblinkingandthe"1"and"8"pushbuttonswillilluminatetoindicatethatithas been reset. NOTE: It is normal for this switch to make a slight buzzing sound during operation. LED Indicators Dimensions Weight Mounting Input Power InputFrequency OperatingTemperature 38A00-2 8 18GA Yes 4.1x1.7x1.5 0.25 lb. WEB VERSION SETUP MODE To configure the Leviton UPB™ 8-Button House Controller using an Leviton controller or a PC running the UPB™ UPStart configurationsoftware,itmustbeputintoSetupModeasfollows: Standard J Box 120±12VAC 60±3Hz -40°Fto104°F FCC Compliance ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycause harmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor televisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures: - Reorient or relocate the receiving antenna. -Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected. -Increasetheseparationbetweentheequipmentandreceiver. -Consultthedealeroranexperiencedradio/TVtechnicianforhelp. FOR CANADA ONLY Forwarrantyinformationand/orproductreturns,residentsofCanadashouldcontactLevitoninwritingatLeviton Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320. LEVITON LIMITED WARRANTY Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that products manufactured by Leviton under the Leviton brand name (“Product”) will be free from defects in material and workmanship for the time periods indicated below, whichever is shorter: • OmniPro II and Lumina Pro: three (3) years from installation or 42 months from manufacture date. • OmniLT, Omni IIe, and Lumina: two (2) years from installation or 30 months from manufacture date. • Thermostats, Accessories: two (2) years from installation or 30 months from manufacture date. • Batteries: Rechargeable batteries in products are warranted for ninety (90) days from date of purchase. Note: Primary (non-rechargeable) batteries shipped in products are not warranted. Products with Windows® Operating Systems: During the warranty period, Leviton will restore corrupted operating systems to factory default at no charge, provided that the product has been used as originally intended. Installation of non-Leviton software or modification of the operating system voids this warranty. Leviton’s obligation under this Limited Warranty is limited to the repair or replacement, at Leviton’s option, of Product that fails due to defect in material or workmanship. Leviton reserves the right to replace product under this Limited Warranty with new or remanufactured product. Leviton will not be responsible for labor costs of removal or reinstallation of Product. The repaired or replaced product is then warranted under the terms of this Limited Warranty for the remainder oftheLimitedWarrantytimeperiodorninety(90)days,whicheverislonger.ThisLimitedWarrantydoesnotcoverPC-basedsoftwareproducts.Leviton is not responsible for conditions or applications beyond Leviton’s control. Leviton is not responsible for issues related to improper installation, including failure to follow written Installation and operation instructions, normal wear and tear, catastrophe, fault or negligence of the user or other problems external to the Product. To view complete warranty and instructions for returning product, please visit us at www.leviton.com. Usehereinofthirdpartytrademarks,servicemarks,tradenames,brandnamesand/orproductnamesareforinformationalpurposesonly,are/maybethetrademarksoftheir respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement. © 2013 Leviton Mfg. Co., Inc. For Technical Assistance Call: 800-824-3005 - www.leviton.com DI-022-HL382-05AAR2243
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021