Well Traveled Living | FireSense 02412 | Owner`s manual | Well Traveled Living FireSense 02412 Owner`s manual

STANDARD PATIO HEATER
Owner’s
Manual
*** I M P O R T A N T N O T I C E * **
Do NOT return to place of purchase!!
Please contact our Toll Free Hotline:
(866) 985-7877
for customer service & warranty issues
Web: www.wtliving.com
Email: cservice@welltraveled.net
R
Amelia Island, FL 32034
IMPORTANT
Read this manual carefully before
assembling, using or servicing this
heater. Keep this manual for future
reference.
R
R
CSA International Requirement NO.5.90.US (5th Edition)
Owner’s Manual for Fise Sense Model
Numbers 02413, 02412, 02411
Contents
DANGER
General Safety Information.................................................. 1
Assembly Instructions
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
Components & Hardware.................................................. 3
Additional Requirements ................................................... 3
WARNING
Installation Process
Step1 - Attach Wheel Assembly to Base............................ 4
Step 2 – Attach Bucket to Base.......................................... 4
WARNING indicates an imminently hazardous situation
which, if not avoided, could result in death or serious injury.
Step 3 –Attach Support Brackets to Base.......................... 5
Step 4 – Attach Post to Support Brackets........................... 5
CAUTION
Step 5 – Load Cylinder Housing onto Post......................... 5
Step 6 – Attach Reflector Studs to Top of Head Assembly.. 5
Step 7 – Attach Head Assembly to Post............................. 5
Step 8 – Install Reflector..................................................... 6
Step 9 – Attach Reflector Assembly to Studs..................... 6
CAUTION indicates an imminently hazardous situation
which, if not avoided, may result in minor or moderate
personal injury, or property damage.
Step 10 – Connect Hose & Regulator to Cylinder............... 6
Leak Check......................................................................... 9
Operation............................................................................ 9
Operation Checklist
10
Troubleshooting.................................................................. 11
Maintenance....................................................................... 11
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapor and liquids in the vicinity of
this or any other appliance.
Storage............................................................................... 12
Service................................................................................ 12
Warranty.............................................................................. 13
WARNING: For Outdoor Use Only
General Safety Information
WARNING
This manual contains important information about the
assembly, operation and maintenance of this patio heater.
General safety information is presented in these first few
pages and is also located throughout the manual.
Keep this manual for future reference and to educate
new users of this product. This manual should be read in
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Read
the instructions
thoroughly before installing or servicing this
equipment.
conjunction with the labeling on the product.
Safety precautions are essential when any mechanical
or
propane
fueled
equipment
is
involved.
precautions are necessary when using, storing, and
servicing. Using this equipment with the respect and
caution demanded will reduce the possibilities of personal
injury or property damage.
The following symbols shown to the right and below are
used extensively throughout this manual. Always heed
these precautions, as they are essential when using
any mechanical or fueled equipment.
DANGER
These
Failure to comply with the precautions and instructions
provided with this heater can result in death, serious bodily
injury and property loss or damage from hazards of fire,
explosion, burn, asphyxiation, and/or carbon monoxide
poisoning.
Only persons who can understand and follow the
instructions should use or service this heater.
1
DANGER
DANGER
• EXPLOSION - FIRE HAZARD
• Keep solid combustibles, such as building materials,
paper or cardboard, a safe distance away from the heater
as recommended by the instructions.
• Provide adequate clearances around air openings into
the combustion chamber.
• Never use the heater in spaces which do or may contain
volatile or airborne combustibles, or products such as
gasoline, solvents, paint thinner, dust particles or unknown
chemicals.
• CARBON MONOXIDE HAZARD
• This heater is a combustion appliance. All combustion
appliances produce carbon monoxide (CO) during the
combustion process. This product is designed to produce
extremely minute, non-hazardous amounts of CO if used
and maintained in accordance with all warnings and
instructions. Do not block air flow into or out of the heater.
• Carbon Monoxide (CO) poisoning produces flu-like
symptoms, watery eyes, headaches, dizziness, fatigue and
• During operation, this product can be a source of
possibly death. You can't see it and you can't smell it. It's
ignition. Keep heater area clear and free from combustible
an invisible killer. If these symptoms are present during
materials, gasoline, paint thinner, cleaning solvents and
operation of this product get fresh air immediately!
other flammable vapors and liquids. Do not use heater in
• For outdoor use only .
areas with high dust content. Minimum heater clearances
• Never use inside house, or other unventilated or
from combustible materials: three (3) feet from the sides &
two (2) feet from the top.
enclosed areas.
• This heater consumes air (oxygen). Do not use in
unventilated or
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish open flame.
3. If odor continues, immediately call your gas
supplier.
enclosed areas to avoid endangering
your life.
CAUTION
• SERVICE SAFETY
• Keep all connections and fittings clean. Make sure
propane cylinder valve outlet is clean.
• Inspect hose before use. Replace if there is evidence of
WARNING
abrasion or wear.
• During set up, check all connections and fittings for leaks
We cannot foresee every use which may be made of our
using soapy water. Never use a flame.
heaters.
• Use as a heating appliance only. Never alter in any way or
Check with your local fire safety authority if you have
use with any device.
questions about heater use.
• Check entire hose at least annually.
Other standards govern the use of fuel gases and heat
producing products for specific uses. Your local authorities
can advise you about these.
If no local codes exist, follow National Fuel Gas Code,
WARNING
• BURN HAZARD
ANSI Z223.1. In Canada, installation must conform to local
• Never leave heater unattended when hot or in use.
codes. If no local codes exist, follow the current National
• Keep out of reach of children.
standards of CANADA CAN/CGA-B 149.2.
2
WARNING
• This product is fueled by propane gas. Propane gas is
invisible, odorless, and flammable. An odorant is normally
added to help detect leaks and can be described as a
“rotten egg” smell. The odorant can fade over time so
leaking gas is not always detectable by smell alone.
Assembly Instructions
Components
Remove all components from package.
Reflector Panel(3)
Reflector Plate
• Propane gas is heavier than air and leaking propane will
sink to the lowest level possible. It can ignite by ignition
Reflector Assembly
sources including matches, lighters, sparks or open flames
of any kind many feet away from the original leak. Use only
propane gas set up for vapor with draw.
• Propane gas should be stored or used in compliance with
Reflector Stud(3)
Heater Burner
Screen
local ordinances and codes or with ANSI/NFPA 58. Turn off
propane when not in use.
Head Assembly
Cylinder Housing
DANGER
• EXPLOSION - FIRE HAZARD
Post
• Never store propane near high heat, open flames, pilot
lights, direct sunlight, other ignition sources or where
temperatures exceed 120 degrees F (49°C).
• Propane is heavier than air and can accumulate in low
places. If you smell gas, leave the area immediately.
• Never install or remove propane cylinder while heater is
lighted, near flame, pilot lights, other ignition sources or
Support Bracket(3)
while heater is hot to touch.
• This heater is red hot during use and can ignite
flammables too close to the burner. Keep flammables at
least 3 feet from sides & 2 feet from top. Keep gasoline and
other flammable liquids and vapors well away from heater.
Gas Hose Less
Regulator
• The propane cylinder must always be stored outdoors in a
well ventilated space. Never store propane cylinder in an
enclosed area (house, garage, etc.). If heater is to be
Regulator
Base
stored indoors, disconnect the propane cylinder for outdoor
storage.
3
Hardware
Picture
Installation process
Used in
Qty
Description
6
Large Bolt
4
5
Medium Bolt
1&3
4
Small Bolt
4
Large Screw
2
9
Small Screw
8
Large Flat
9
Washer
Small Flat
9
2
6
Washer
Large Flange
Nut
Small Flange
Nut
Step(s)
(For models without wheels, skip to step 2)
.
.
Step 1 – Attach Wheel Assembly to Base
Line up holes in Wheel Bracket with corresponding
holes in Base, Insert 2 Medium Bolts through holes,
finger tighten 2 Large Flange Nuts.
Be sure that the Wheel Assembly is parallel to the
base, and fully tighten bolts.
Wheel Assembly
6&9
8
1
4
4
Large Nut
2
9
Cap Nut
8
3
Wing Nut
9
3
Reflector Stud
6
1
Wrench
2 Req’d Medium Bolts
1/3/4/
7/8
2 Req’d Large Flange Nuts
(For models without bucket, skip to step 3)
Step 2 – Attach Bucket to Base
Bucket
Additional Requirements
The following items are not included, but are necessary for
..
..
the proper assembly of your heater. Do NOT attempt to
assemble without proper tools.
7/16” open-end wrench.
Philips screwdriver w/ medium blade.
Adjustable opening wrench.
Leak Detection Solution(Instructions on how to make
solution are included on page 8 )
.
Slip 4 Large Screw through holes of Base.
Note: You must follow all steps to properly assemble
heater.
4
4 Req’d Large Screws
4 Req’d Large Nuts
.
.
.
Lay Bucket inside of Base and screw on large nut.
Tighten with Philips screwdriver.
..
Step 5 – Load Cylinder Housing onto Post
Load Cylinder Housing onto Post.
Slide Cylinder Housing down.
Fill the bucket with Sand.
Step 3 – Attach Support Brackets to Base
Attach three Support Brackets loosely to Base with
three medium bolts downward through Support
Brackets into the Base.
3 Req’d Medium Bolts
..
Step 6 – Attach Reflector Studs to
Top of Head Assembly
..
Step 4 – Attach Post to Support Brackets
Tighten studs securely.
Install Post onto three Support Brackets.
Attach Post to Support Brackets using six large bolts
3 Req’d Reflector Studs
3 Req’d Large Flat Washers
& six flange nuts.
6 Req’d Large Bolts
.
Insert 3 Reflector Studs & 3 Flat Washers.
.
Step 7 – Attach Head Assembly to Post
Screw off 4 small bolts.
6 Req’d Small Flange Nut
Fully tighten all of the screws.
4 Req’d Small Bolts
Head Assembly
5
..
.
Load Head Assembly by inserting hose into post.
Insert Head Assembly into post.
9 Req’d Small Screw s
Control knob should be above decal on post.
.
9 Req’d Small Flat Washers
.
.
9 Req’d Cap Nuts
Slide one Small Flat Washer over threaded end of
screw and screw on Cap Nut loosely.
Attach Head Assembly to post, and loosely install four
small bolts.
Tighten bolts securely.
(For models with one piece reflector, skip to step 9)
.
.
Step 8 – Install Reflector
WARNING
Remove protective cover before assemble.
Slide Reflector Plate
onto Reflector Panels.
Insert
Screw.
one
Small
.
Slide one Small Flat
Washer over threaded
end
of
screw on
screw
and
Cap
Nut
loosely.
Note: If necessary for proper alignment of reflector
.
.
sections, loose each screw prior to further assembly and
retighten after sections are aligned.
6
Slide
two
Reflector
Panels together.
Insert
Screw.
one
Small
.
.
Repeat procedure to complete the assembly of all four
sections.
Fully tighten all of the screws in the rolled edge.
..
Step 9 – Attach Reflector Assembly to Studs
Support Heater.
Slide 3 Large Flat Washers over threaded end of
Studs.
6 Req’d Large Flat Washers
..
.
.
3 Req’d Wing Nuts
Locate Reflector Assembly on 3 studs.
Install large flat washers on studs & securely tighten
wing nuts but do not over-tighten!
Step 10 – Connect Hose & Regulator to Cylinder
You
must
propane
provide
gas
and
propane cylinder. Use a
standard 20 lb. propane
cylinder only.
.
.
.
.
..
..
.
The pressure regulator and hose assembly supplied
with the appliance must be used.
The installation must conform with local codes, or in
the absence of local codes, with National Fuel Gas
Code, ANSI Z223.1.
A dented, rusted or damaged propane cylinder may
be hazardous and should be checked by your cylinder
supplier. Never use a propane cylinder with a
damaged valve connection.
The propane cylinder must be constructed and
marked in accordance with the specifications for LP
gas
cylinders
of
the
U.S.
Department
of
Transportation (DOT).
Never connect an unregulated propane cylinder to the
heater.
Lift Cylinder Housing.
Screw regulator onto gas hose. Do not cross-thread.
Tighten securely.
Attach regulator to cylinder.
Complete attachment.
Use this heater only
with a propane vapor
withdrawal
supply
.
system. See Chapter 5
of
the
Standard
for
Storage and Handling
of Liquified Petroleum
Gas,
.
.
Install cylinder.
ANSI/NFPA
58.Your local library or
Standard 20 lb. tank
fire department will have this book.
A minimum supply pressure of 11.0 W.C. is required
for the purpose of input adjustment for propane gas.
7
Leak Check
Operation
WARNING
DANGER
• Perform all leak tests outdoors.
• Extinguish all open flames.
• CARBON MONOXIDE HAZARD
• NEVER leak test when smoking.
• Do not use the heater until all connections have been leak
• For outdoor use only. Never use inside house, or other
tested and do not leak.
unventilated or enclosed areas. This heater consumes air
(oxygen). Do not use in unventilated or enclosed areas to
avoid endangering your life.
DANGER
• EXPLOSION - FIRE HAZARD
.
.
.
..
..
.
• Never store propane near high heat, open flames, pilot
Hose / Regulator
Regulator / Cylinder
Connection
Connection
lights, direct sunlight, other ignition sources or where
temperatures exceed 120 degrees F (49°C).
Make 2-3 oz. of leak check solution (one part liquid
dishwashing detergent and three parts water).
• Propane is heavier than air and can accumulate in low
places. If you smell gas, leave the area immediately.
Apply several drops of solution where hose attaches
to regulator.
• Never install or remove propane cylinder while heater is
lighted, near flame, pilot lights, other ignition sources or
Apply several drops of solution where regulator
connects to Cylinder.
while heater is hot to touch.
• This heater is red hot during use and can ignite
Make sure all Patio Heater & Light valves are OFF.
Turn Cylinder Valve ON.
flammables too close to the burner. Keep flammables at
least 3 feet from sides & 2 feet from top. Keep gasoline and
If bubbles appear at any connection, there is a leak.
other flammable liquids and vapors well away from heater.
Turn Cylinder Valve OFF.
• The propane cylinder must always be stored outdoors in a
If leak is at Hose/Regulator connection: tighten
connection and perform another leak test.
well ventilated space. Never store propane cylinder in an
enclosed area (house, garage, etc.). If heater is to be
If leak is at Regulator/Cylinder Valve connection:
disconnect, reconnect, and perform another leak
stored indoors, disconnect the propane cylinder for outdoor
storage.
check. If you continue to see bubbles after several
attempts, cylinder valve is defective and should be
returned to cylinder’s place of purchase.
.
.
If
NO
bubbles
appear
at
any connection,
Caution: Do not attempt to operate until you have read
the
connections are secure.
Turn Cylinder Valve OFF.
& understand all General Safety Information in this
manual and all assembly is complete & leak checks
have been performed.
NOTE: Whenever gas connections are loosened or
removed, you must perform a complete leak test.
8
Complete installation.
Before Turning Gas Supply ON:
.
.
..
..
.
.
.
Your heater was designed and approved for outdoor
4
visible through Viewing Hole.
use only. Do NOT use it inside a building, garage, or
any other enclosed area.
5
Release Control Knob after 30-60 seconds. Pilot
Light will remain lit. If not, return to step 1.
Make sure surrounding areas are free of combustible
materials, gasoline, and other flammable vapors or
Push and release the igniter button until pilot flame is
6
Turn Control Knob to ON. Main Burner will light
liquids.
immediately. Flame is visible through Viewing Hole. If
Ensure that there is no obstruction to air ventilation.
not, return to step 1.
Be sure all gas connections are tight and there are no
leaks.
Be sure the cylinder cover is clear of debris.
Be sure any component removed during assembly or
servicing is replaced and fastened prior to starting.
Before Lighting:
Heater should be thoroughly inspected before eachuse, and by a qualified service person at least
annually.
If relighting a hot heater, always wait at least 5
minutes.
Inspect the hose assembly for evidence of excessive
abrasion, cuts, or wear. Suspected areas should be
leak tested. If the hose leaks, it must be replaced prior
to operation. Only use the replacement hose
assembly specified by manufacturer.
.
If for some reason your igniter fails to deliver a spark,
your heater can be started by inserting a lit long
fireplace match through the pilot view hole while
pushing the control knob in while in the PILOT position.
Lighting:
Note: This heater is equipped with a Pilot Light that allows
for safer startups and shutdowns. Pilot must be lit before
Main Burner can be started.
1
Turn Cylinder Valve ON.
2
Open Viewing Hole by sliding cover to either side.
3
Push Control Knob IN and rotate to Pilot position.
Note: For initial start or after any cylinder change, hold
Note: If pilot fails to remain lit, all valves should be closed
Control Knob IN for 2 minutes to purge air from gas lines
and waiiting period of at least 5 minutes should pass before
before proceeding.
attempting to light.
9
If
you
experience
any
ignition
problem please
consult “Troubleshooting” on page 11.
Caution: Avoid inhaling fumes
emitted from the
heater’s first use. Smoke and odor from the burning of
oils used in manufacturing will appear. Both smoke
and odor will dissipate after approximately 30 minutes.
The heater should NOT produce thick black smoke.
Note: The burner may be noisy when initially turned on. To
.
.
.
Shut Down:
Turn Control Knob clockwise to Pilot. (Normally,
burner will make a slight popping sound when
extinguished.) Burner will extinguish but Pilot will
remain ON.
To extinguish Pilot, depress Control Knob and
continue to turn it clockwise to OFF.
Turn Cylinder Valve clockwise to OFF and disconnect
Regulator when heater is not in use.
eliminate excessive noise from the burner, turn the Control
Note: After use, some discoloration of the emitter screen is
Knob to the Pilot position. Then, turn the knob to the level
normal.
of heat desired.
Operation Checklist
WARNING
FOR YOUR SAFETY
Be careful when attempting to manually ignite this heater.
Holding in the control know for more than 10 seconds
before igniting the gas will cause a ball of flame upon
ignition.
When heater is ON:
Emitter screen will become bright red due to intense heat.
The color is more visible at night.
Burner will display tongues of blue and yellow flame. These
flames should not be yellow or produce thick black smoke,
indicating an obstruction of airflow through the burners. The
flame should be blue with straight yellow tops.
If excessive yellow flame is detected, turn off heater and
consult “Troubleshooting” on page 11.
Re-lighting:
Note: For your safety, the Control Knob cannot be turned
..
.
OFF without first depressing the Control Knob in PILOT
position and then rotating it to OFF.
Turn Control Knob to OFF.
Wait at least 5 minutes, to let gas dissipate, before
attempting to relight Pilot.
Repeat the “Lighting” steps on prior page.
..
..
..
..
..
.
.
.
..
Before Operating:
I am familiar with entire owner’s manual and
understand all precautions noted in the manual.
All components are properly assembled, intact and
operable.
No alterations have been made.
All gas connections are secure and do not leak.
Wind velocity is below 10 mph.
Outdoor temperature is greater than 40 degrees F.
Heater is outdoors (outside any enclosure).
There is adequate fresh air ventilation.
Heater is away from gasoline or other flammable
liquids or vapors.
Heater is away from windows, air intake openings,
sprinklers and other water sources.
Heater is at least 36” from combustible materials.
Heater is on a hard and level surface.
There are no signs of spider or insect nests.
All burner passages are clear.
All air circulation passages are clear.
Children, pets, clothing, flammable materials and
items that can be damaged from radiant heat are
away from the heater.
Children and adults in the area have been alerted to
the high temperature hazards: especially burns and
clothing fires.
Children and adults in the area have been warned not
to touch heater near the burner head during operation
and until unit has cooled.
After Operation:
WARNING
FOR YOUR SAFETY
Heater will be hot after use. Handle with extreme care.
10
For a safe and pleasurable heating experience, perform
this check before each use.
Gas control is in OFF position.
Gas Tank valve is OFF.
Disconnect Gas line.
Heater is upright in a secure location.
Troubleshooting
If the problem is:
And this condition exists:
Then do this
Cylinder valve is closed
Open valve
Blockage in orifice or pilot tube
Clean or replace orifice or pilot tube
Open gas line and bleed it (pressing control
Pilot won’t light
Air in gas line
knob in) for not more than 1 - 2 minutes or
until
you smell gas
Low gas pressure with cylinder valve
Note:
Heater
operates
at
reduced efficiency below 40ºF
fully open
Use long fireplace match to light pilot; obtain new
Igniter fails
igniter and replace
(5ºC)
Dirt built up around pilot
Clean dirt from around pilot
Connection between gas valve and
Pilot won’t stay lit
Tighten connection and perform leak check
pilot assembly is loose
Burner won’t light
Thermocouple is not operating correctly
Replace thermocouple
Gas pressure is low
Turn cylinder valve OFF and replace cylinder
Blockage in orifice
Clear blockage
Control knob is not in ON position
Turn control knob to ON
Gas pressure is low
Turn cylinder valve OFF and replace cylinder
Outdoor temperature is less than
Burner flame is low
Turn cylinder valve OFF and replace cylinder
40ºF
and tank is less than 1/4 full
Use a full cylinder
Supply hose is bent or kinked
Straighten hose
Control knob fully ON
Check burner and orifices for blockage
Carbon build-up
Dirt or film on reflector and burner screen
Clean reflector and burner screen
Thick black smoke
Blockage in burner
Maintenance
Remove blockage and clean burner inside and
outside
c.Keeping the ventilation opening(s) of the cylinder enclosure
free and clear from debris.
d. Visually checking burner flames , with pictorial representations.
WARNING
FOR YOUR SAFETY:
• Do NOT touch or move heater for at least 45 minutes
after use.
• Reflector is hot to the touch.
• Allow reflector to cool before touching.
e. Cleaning the appliance , including special surfaces , with
recommended cleaning agents , if necessary.
f. Lubrication of moving parts and the type and amount of lubricant
to be used.
g. When applicable , visually checking portions of the hose
assembly located within the confines of the heater post.
a. Keeping the appliance area clear and free from combustible
materials , gasoline and other flammable vapors and liquids.
Air flow must be unobstructed. Keep controls, burner,
b. Not obstructing the flow of combustion and ventilation air.
blockage include:
and circulating air passageways clean. Signs of possible
11
..
..
.
.
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heater glow is excessively uneven.
Heater makes popping noises.
Ґ
.
.
.
Store heater upright in an area sheltered from direct
contact with inclement weather (such as rain, sleet,
hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces
and to help prevent build up in air passages.
Never leave LP cylinder exposed to direct sunlight or
excessive heat.
Note: Wait until heater is cool before covering.
Spiders and insects can nest in burner or orifices.
This dangerous condition can damage heater and
Service
render it unsafe for use. Clean burner holes by using
a heavy-duty pipe cleaner. Compressed air may help
Repair to gas passages and associated components
clear away smaller particles.
should be done only by a qualified service person.
Carbon deposits may create a fire hazard. Clean
dome and burner screen with warm soapy water if
Caution:
any carbon deposits develop.
attempting service.
Note: In a salt-air environment (such as near an ocean),
corrosion occurs more quickly than normal. Frequently
check for corroded areas and repair them promptly.
TIP:
Use high-quality automobile wax to help maintain the
appearance of your heater. Apply to exterior surfaces from
the pole down. Do not apply to emitter screen or domes.
Storage
..
.
.
Between uses:
Turn Control Knob OFF.
Disconnect LP source.
Store heater upright in an area sheltered from direct
contact with inclement weather (such as rain, sleet,
hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces
and to help prevent build up in air passages.
Note: Wait until heater is cool before covering.
..
During periods of extended inactivity or when
transporting:
12
Turn Control Knob OFF.
Disconnect LP source and move to a secure,
well-ventilated location outdoors.
Always
allow
heater
to
cool
before
WARRANTY
Amelia Island, FL 32034
Toll Free: 866-WTL-SUPP
(985-7877)
R
Web: www.wtliving.com
Email: cservice@welltraveled.net
1 YEAR LIMITED WARRANTY - Customers in the Continental US
All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials
and workmanship under normal use. This warranty does NOT cover normal wear and tear and weathering, assembly and or
maintenance OR use in a commercial application. At Well Traveled Living’s sole discretion, products under warranty will be
repaired and/or replaced at no charge to the customer. Any returns sent back to the manufacturer must be sent via prepaid freight.
*** Insure prompt warranty service, return the enclosed warranty registration card within 30 days ***
*** For warranty service contact Well Traveled Living at the address, phone numbers, internet site or e-mail listed in this
owner’s manual. You must have your sales receipt and original date of purchase to obtain warranty service. All warranty service
will be coordinated by the Well Traveled Living’s Amelia Island Florida service center. ***
This warranty is extended only to the original purchaser. Proof of purchase will be required before warranty service is rendered.
Sales receipt and/or validation of warranty registration are valid forms of proof of purchase. This warranty only covers failures due
to defects in materials or workmanship which occur during normal use. Failures and/or damage which result from accident,
negligence, misuse, abuse, neglect, mishandling, alteration or modification, failure to maintain, improper assembly or maintenance,
service by an unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT covered.
*** There are no express warranties except as listed above ***
Purchaser assumes all risks in the assembly and operation of this unit.
FAILURE TO FOLLOW WARNINGS & OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN
SEVERE PROPERTY DAMAGE AND/OR PERSONAL INJURY.
Well Traveled Living shall not be liable for incidental or consequential damages resulting from the use of this product or such damages
arising out of any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages,
or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives
you specific legal rights. You may also have other legal rights which very from state to state.
Fire Sense is a registered trademark of Well Traveled Imports, Inc.
Fire Sense Assembly Instruction presentations are the property of Well Traveled Imports, Inc. and are protected by US Copyrights and Trademarks.
All Rights Reserved.
13
Download PDF