09n1064

09n1064
IBM Netfinity Servers
IBM Netfinity 3000 - Type 8476
Hardware Maintenance Manual
August 1999
We Want Your Comments!
(Please see page 254)
This Manual Supports
The Following Models:
10U, 10X, 11U, 11X,
15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X,
50U, 50X, 51U, 51X,
60U, 61U, 70U, 71U
S10L-9798-04
IBM Netfinity Servers
IBM Netfinity 3000 - Type 8476
Hardware Maintenance Manual
August 1999
We Want Your Comments!
(Please see page 254)
IBM
S10L-9798-04
Note
Before using this information and the product it
supports, be sure to read the general information
under “Notices” in the manual.
Fifth Edition (August 1999)
The following paragraph does not apply to the United
Kingdom or any country where such provisions are
inconsistent with local law: INTERNATIONAL
BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some states do not allow disclaimer of
express or implied warranties in certain transactions,
therefore, this statement may not apply to you.
This publication could include technical inaccuracies or
typographical errors. Changes are periodically made to
the information herein; these changes will be incorporated
in new editions of the publication. IBM may make
improvements and/or changes in the product(s) and/or the
program(s) described in this publication at any time.
This publication was developed for products and services
offered in the United States of America. IBM may not offer
the products, services, or features discussed in this
document in other countries, and the information is subject
to change without notice. Consult your local IBM
representative for information on the products, services,
and features available in your area.
Requests for technical information about IBM products
should be made to your IBM reseller or IBM marketing
representative.
 Copyright International Business Machines
Corporation 1999. All rights reserved.
Note to U.S. Government users–Documentation related to
Restricted rights–Use, duplication, or disclosure is subject
to restrictions set forth in GSA ADP Schedule Contract
with IBM Corp.
ii
Netfinity Server HMM
About this supplement
This supplement contains diagnostic information,
Symptom-to-FRU Indexes, service information, error
codes, error messages, and configuration information for
the Netfinity 3000 - Type 8476.
Important
This manual is intended for trained servicers who are
familiar with IBM PC Server products.
Before servicing an IBM product, be sure to review
“Safety information” on page 210.
Important Safety Information
Be sure to read all caution and danger statements in this
book before performing any of the instructions.
Leia todas as instruções de cuidado e perigo antes de
executar qualquer operação.
Prenez connaissance de toutes les consignes de type
Attention et
Danger avant de procéder aux opérations décrites par les
instructions.
iii
Lesen Sie alle Sicherheitshinweise, bevor Sie eine
Anweisung ausführen.
Accertarsi di leggere tutti gli avvisi di attenzione e di
pericolo prima di effettuare qualsiasi operazione.
Lea atentamente todas las declaraciones de precaución y
peligro ante
de llevar a cabo cualquier operación.
Online support
Use the IBM Personal computing solutions (BBS) or the
World Wide Web (WWW) to download Diagnostic, BIOS
Flash, and Device Driver files.
File download address is:
http://www.ibm.com/pc/files.html
The IBM BBS can be reached at (919) 517-0001.
IBM online addresses:
The HMM manuals online address is:
http://www.ibm.com/pc/us/cdt/hmm.html
The IBM Support Page is:
http://www.ibm.com/support/
The IBM Personal computing solutions page.
http://www.ibm.com/pc/
iv
Netfinity Server HMM
Contents
About this supplement . . . . . . . . . . . . . . .
Important Safety Information
. . . . . . . . . .
Online support . . . . . . . . . . . . . . . . .
IBM Netfinity 3000 - Type 8476
General Checkout . . . . . . .
Diagnostics . . . . . . . . . .
Features . . . . . . . . . . .
Additional service information
.
Locations . . . . . . . . . . .
Symptom-to-FRU index . . . .
Undetermined problems . . . .
Parts listing (Netfinity 3000 - Type
. . .
. . .
. . .
. . .
. . .
. . .
. . .
. . .
8476)
Related service information
. .
Safety information . . . . . . . .
Battery notice (lithium)
. . . . .
Battery notice (nickel cadmium)
.
Laser compliance statement . . .
Send us your comments!
. . . .
Problem determination tips
. . .
Phone numbers, U.S. and Canada
Trademarks
. . . . . . . . . .
 Copyright IBM Corp. 1999
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
iii
iii
iv
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
.
4
.
6
. 15
. 17
. 58
160
198
199
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
209
210
215
218
252
254
255
256
258
v
vi
Netfinity Server HMM
IBM Netfinity 3000 - Type 8476
General Checkout . . . . . . . . . . . . . . . . .
Diagnostics . . . . . . . . . . . . . . . . . . . .
Diagnostic test programs . . . . . . . . . . . .
Power-on self-test (POST) . . . . . . . . . . .
POST beep codes . . . . . . . . . . . . . . .
Error messages . . . . . . . . . . . . . . . .
POST error messages and beep codes
. . .
SCSI error messages . . . . . . . . . . . .
Diagnostic error messages
. . . . . . . . .
Software-generated error messages . . . . .
Installing files from option diskettes . . . . . . .
Running the diagnostic test programs . . . . . .
Power-on self-test (POST) messages . . . . . .
Viewing the test log
. . . . . . . . . . . . . .
SIMM/DIMM errors . . . . . . . . . . . . .
Features . . . . . . . . . . . . . . . . . . . . .
Additional service information
. . . . . . . . . . .
Configuration overview . . . . . . . . . . . . .
Configuration conflicts
. . . . . . . . . . . . .
Hardware configuration conflicts . . . . . . .
Software configuration conflicts
. . . . . . .
Configuration/Setup utility program
. . . . . . .
Configuration/Setup utility program menus . . . .
System summary . . . . . . . . . . . . . .
Product data . . . . . . . . . . . . . . . .
Devices and I/O ports . . . . . . . . . . . .
Start options . . . . . . . . . . . . . . . .
Date and time
. . . . . . . . . . . . . . .
System security
. . . . . . . . . . . . . .
Setting power-on password modes . . . .
Setting and changing a power-on password
Using the administrator password menu
.
Using the enhanced security features . . .
Restricting access to IDE devices and
diskette drives . . . . . . . . . . . . .
Remote administration . . . . . . . . . .
Setting Adapter ROM security
. . . . . .
Advanced setup
. . . . . . . . . . . . . .
Cache control . . . . . . . . . . . . . .
ROM shadowing
. . . . . . . . . . . .
PCI control
. . . . . . . . . . . . . . .
Plug and Play control
. . . . . . . . . .
Processor control
. . . . . . . . . . . .
ISA legacy resources . . . . . . . . . . . .
Power management
. . . . . . . . . . . .
Using the Automatic configuration and power
interface BIOS mode . . . . . . . . . .
Configuring the Ethernet controller
. . . . . . .
Troubleshooting the 10/100 Mbps Ethernet
Controller . . . . . . . . . . . . . . . . .
Network connection problems
. . . . . .
 Copyright IBM Corp. 1999
4
6
7
8
9
9
9
9
9
10
10
11
11
14
14
15
17
18
20
20
21
21
24
25
25
25
26
26
27
27
29
31
32
33
34
35
35
35
35
35
35
36
36
37
37
38
40
40
1
Diagnostic LEDs
. . . . . . . . . . . .
Erasing lost or forgotten passwords . . . . . . .
Power supply
. . . . . . . . . . . . . . . . .
ROM operation mode switch setting . . . . . . .
SCSISelect utility program
. . . . . . . . . . .
Starting the SCSISelect utility program . . . .
SCSISelect utility program choices . . . . . .
Configure/View host adapter settings
. . . .
SCSI disk utilities
. . . . . . . . . . . .
Performing a low-level disk format
. . . .
When to use the format disk program . . .
Starting the low-level format
. . . . . . .
Specifications (Ethernet cable)
. . . . . . . . .
Wake on LAN feature . . . . . . . . . . . .
Specifications (system) . . . . . . . . . . . . .
Locations . . . . . . . . . . . . . . . . . . . . .
Accessing the system board
. . . . . . . . . .
Adapters
. . . . . . . . . . . . . . . . . . .
Adapter considerations
. . . . . . . . . . .
AGP adapters . . . . . . . . . . . . . .
ISA and PCI adapters . . . . . . . . . .
Installing or removing ISA and PCI adapters .
Installing or removing AGP adapters . . . . .
Adding security options
. . . . . . . . . . . .
Installing a U-bolt and security cable . . . . .
Battery
. . . . . . . . . . . . . . . . . . . .
Bottom cover
. . . . . . . . . . . . . . . . .
Cabling . . . . . . . . . . . . . . . . . . . .
CD-ROM drive . . . . . . . . . . . . . . . . .
Handling a CD . . . . . . . . . . . . . . .
Loading and unloading a CD
. . . . . . . .
Completing the installation . . . . . . . . . . .
Controls and indicators . . . . . . . . . . . . .
Server controls . . . . . . . . . . . . . . .
Status indicators
. . . . . . . . . . . . . .
Disconnecting cables and removing the side cover
External options . . . . . . . . . . . . . . . .
Adding a hot-swap storage expansion enclosure
External SCSI devices . . . . . . . . . . . . .
Serial port connectors . . . . . . . . . . . .
Parallel port connector
. . . . . . . . . . .
External view
. . . . . . . . . . . . . . . . .
Front fan
. . . . . . . . . . . . . . . . . . .
Input/Output connectors
. . . . . . . . . . . .
Internal drives . . . . . . . . . . . . . . . . .
Expansion bays
. . . . . . . . . . . . . .
Drive specifications . . . . . . . . . . . . .
Types of cables
. . . . . . . . . . . . .
SCSI drives
. . . . . . . . . . . . . . .
SCSI physical unit numbers
. . . . . .
SCSI logical unit number . . . . . . . .
Termination requirements
. . . . . . .
Preinstallation steps (all bays) . . . . . . .
Working with drives in bays 1 through 4
. .
2
Netfinity Server HMM
41
42
45
47
49
49
49
49
50
51
51
51
53
55
56
58
59
60
60
60
61
62
65
67
67
69
71
73
74
75
75
77
81
81
82
84
87
87
88
89
90
91
92
94
97
97
99
100
104
104
104
105
105
107
Installing drives in the permanently
mounted drive cage
. . . . . . . .
Removing drives in the permanently
mounted drive cage
. . . . . . . .
Removing the removable drive cage
.
Installing a drive in the removable drive
cage
. . . . . . . . . . . . . . .
Working with drives in Bays 5 and 6 . . .
Internal view . . . . . . . . . . . . . . . .
Memory modules
. . . . . . . . . . . . .
Memory configuration . . . . . . . . . .
Installing or removing memory modules
.
Microprocessors . . . . . . . . . . . . . .
Installing or replacing microprocessors . .
Preliminary option installation information
. .
Stabilizing feet . . . . . . . . . . . . . . .
System board . . . . . . . . . . . . . . .
System board illustration . . . . . . . . . .
System board replacement . . . . . . . . .
Switch settings
. . . . . . . . . . . . . .
Administrator password switch setting
. .
Diskette write-protect switch setting
. . .
Ethernet controller operation mode switch
setting
. . . . . . . . . . . . . . . .
Updating the server configuration . . . . . .
Video port connector . . . . . . . . . . . .
Microprocessor speed switches settings
.
Keyboard and mouse connectors
. . . .
SCSI connectors . . . . . . . . . . . .
Internal SCSI connector . . . . . . .
External SCSI connector . . . . . . .
Universal serial bus ports . . . . . . . .
Ethernet connector . . . . . . . . . . .
Symptom-to-FRU index . . . . . . . . . . . .
No beep symptoms
. . . . . . . . . . . .
Beep symptoms . . . . . . . . . . . . . .
POST error codes . . . . . . . . . . . . .
Diagnostic error codes . . . . . . . . . . .
Ethernet controller messages . . . . . . . .
Miscellaneous symptoms . . . . . . . . . .
SCSI messages . . . . . . . . . . . . . .
Undetermined problems . . . . . . . . . . . .
Parts listing (Netfinity 3000 - Type 8476) . . . .
System . . . . . . . . . . . . . . . . . .
Keyboards
. . . . . . . . . . . . . . . .
Power cords . . . . . . . . . . . . . . . .
.
108
.
.
112
114
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
116
121
125
126
127
127
130
131
136
138
139
142
144
145
145
147
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
149
150
152
153
155
156
156
156
158
159
160
160
160
163
167
189
191
197
198
199
200
206
208
IBM Netfinity 3000 - Type 8476
3
General Checkout
This general checkout procedure is for Netfinity 3000 Type 8476 servers.
Attention
The drives in the system you are servicing might have
been rearranged or the drive startup sequence
changed. Be extremely careful during write operations
such as copying, saving, or formatting. Data or
programs can be overwritten if you select an incorrect
drive.
Diagnostic error messages appear when a test program
finds a problem with a hardware option. For the test
programs to properly determine if a test Passed, Failed, or
Aborted, the test programs check the error-return code at
test completion.
General error messages appear if a problem or conflict is
found by an application program, the operating system, or
both. For an explanation of these messages, refer to the
information supplied with that software package.
A failed system might be part of a shared DASD cluster
(two or more systems sharing the same external storage
device(s)). Prior to running diagnostics, verify that the
failing system is not part of a shared DASD cluster.
A system might be part of a cluster if:
Ÿ
Ÿ
Ÿ
The customer identifies the system as part of a
cluster.
One or more external storage units are attached to
the system and at least one of the attached storage
units is additionally attached to another system or
unidentifiable source.
One or more systems are located near the failing
system.
If the failing system is suspected to be part of a shared
DASD cluster, all diagnostic tests can be run except
diagnostic tests which test the storage unit (DASD residing
in the storage unit) or the storage adapter attached to the
storage unit.
4
Netfinity Server HMM
Notes
1. For systems that are part of a shared DASD
cluster, run one test at a time in looped mode.
Do not run all tests in looped mode, as this could
enable the DASD diagnostic tests.
2. Before replacing any FRUs, ensure the latest
level of BIOS is installed on the system. A
down-level BIOS might cause false errors and
unnecessary replacement of the system board.
3. If multiple error codes are displayed, diagnose
the first error code displayed.
4. If the server hangs with a POST error, go to
“Symptom-to-FRU index” on page 160.
5. If the server hangs and no error is displayed, go
to “Undetermined problems” on page 198.
6. If an installed device is not recognized by the
diagnostics program, that device might be
defective.
7. If a blank screen, unreadable screen, or other
unusual response occurs, go to
“Symptom-to-FRU index” on page 160.
8. For power supply problems, see “Power supply”
on page 45.
001
IS THE SYSTEM PART OF A CLUSTER?
Yes No
002
Go to Step 004.
003
Schedule maintenance with the customer. Shut down all
systems related to the cluster. Run storage test.
004
–
–
–
–
Power-off the server and all external devices.
Check all cables and power cords.
Set all display controls to the middle position.
Start the diagnostic programs, if necessary see “Running
the diagnostic test programs” on page 11.
– Check for the following responses:
1. One or two beeps (depending on the diagnostics
version level).
2. Readable instructions or the Main Menu.
(Step 004 continues)
IBM Netfinity 3000 - Type 8476
5
(CONTINUED)
004 (continued)
DID YOU RECEIVE THE CORRECT RESPONSES?
Yes No
005
Go to the “Symptom-to-FRU index” on page 160.
006
ARE ALL INSTALLED DEVICES IN THE SERVER
HIGHLIGHTED ON THE MODULE TEST MENU OR
HARDWARE CONFIGURATION REPORT?
Yes No
007
The missing device may be defective.
008
Run the Advanced Diagnostics test. If necessary, refer to
“Diagnostics.”
Ÿ
Ÿ
If you receive an error, go to “Symptom-to-FRU index”
on page 160.
If the test stops and you cannot continue, replace the
last device tested.
Diagnostics
The following tools are available to help identify and
resolve hardware-related problems:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
6
Diagnostic test programs
Power-on self-test (POST)
POST beep codes
Error messages
Troubleshooting charts
Option diskettes
Netfinity Server HMM
Diagnostic test programs
IBM provides programs that you can run to diagnose
hardware and some software problems. Several utility
programs that provide helpful information about the server
are also included. One of these programs provides the
user interface for running these diagnostic and utility
programs.
The server diagnostic test programs are stored on the IBM
Enhanced Diagnostics Diskette that comes with the server.
These programs are the primary method of testing the
system board, memory, and other standard features of the
Netfinity 3000 server. You can also use them to test some
external devices.
Also, if you cannot determine whether a problem is caused
by the hardware or by the software, you can run the test
programs to confirm that the hardware is working properly.
The IBM Enhanced Diagnostics programs will isolate the
server hardware from software that you have installed on
the hard disk. The programs run independently of the
operating system, and must be run either from CD or
diskette. This method of testing is generally used when
other methods are not accessible or have not been
successful in isolating a problem suspected to be hardware
related.
The server diagnostic test programs can identify most
problems associated with major components of the server:
the system board, Ethernet controller, video adapter or
controller, random-access memory (RAM), diskette drive,
serial port, parallel port, keyboard, and mouse.
In addition to the server test programs, the IBM Enhanced
Diagnostics Diskette contains utility programs that provide
information about the server hardware, including the
hardware configuration. This information might be useful
in helping to isolate problems related to the operating
system and device drivers.
The IBM Enhanced Diagnostics Diskette also contains
additional diagnostic programs for non-IBM devices.
See “Running the diagnostic test programs” on page 11
for information on running the diagnostic programs that
come with the server.
IBM Netfinity 3000 - Type 8476
7
Power-on self-test (POST)
When you power-on the server, it performs a series of
tests to check the operation of server components and
some options. This series of tests is called the power-on
self-test, or POST.
POST does the following:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Checks the operation of some basic system board
operations
Checks the memory operation
Compares the current server configuration with the
stored server configuration information
Configures PCI adapters
Starts the video operation
Verifies that the drives (such as the diskette,
CD-ROM, and hard disk drives) are connected
properly
If Power-On Self-Test is set to [Enhanced], numbers that
show the amount of memory being tested appear in the
top-left corner of the screen until the total amount of
memory in the system is reached. Options for running a
quick POST or accessing the Configuration/Setup Utility
program appear in the lower-left corner of the screen.
Quick mode is the default mode of operation. To change
the mode to [Enhanced], select Start Options from the
Configuration/Setup Utility program menu and follow the
prompts on the screen.
Note
The amount of available memory shown might be
somewhat less than expected because of BIOS
shadowing in RAM.
If POST finishes without detecting any problems, the first
screen of the operating system or application program
appears (if you have not set a power-on password). If you
have set a power-on password, a password prompt
appears. You must enter the password before the first
screen of the operating system or application program will
appear. (For further information on using passwords, see
“System security” on page 27.)
If Power-On Status is set to [Enabled] and POST detects
a problem, you will hear multiple beeps or no beep. In
most cases, an error code appears in the top left corner of
the screen, and in some cases, a description of the error is
displayed beside the code. (Note that the screen will
sometimes display multiple error codes and descriptions.)
8
Netfinity Server HMM
POST beep codes
If Power-On Status is set to [Enabled], POST also
generates beep codes to indicate successful completion or
the detection of an error.
Ÿ
Ÿ
The startup of the operating system or application
program indicates successful completion of POST.
More than one beep indicates that POST detected an
error.
For a list of beep codes, see “Symptom-to-FRU index” on
page 160.
Error messages
Error messages indicate that a problem exists; they are not
intended to be used to identify a failing part.
Troubleshooting and servicing of complex problems
indicated by error messages should be performed by a
trained service technician.
Hardware error messages that occur can be text, numeric,
or both. Messages generated by the software generally
are text messages, but they also can be numeric.
POST error messages and beep codes:
POST error messages and beep codes occur during
startup when POST finds a problem with the hardware or
detects a change in the hardware configuration. POST
error messages are 3-, 4-, 5-, 8-, or 12-character
alphanumeric messages and include brief explanations
(except I999XXXX errors).
For a list of error codes, see “Symptom-to-FRU index” on
page 160.
SCSI error messages
: These messages appear if a problem or conflict is
detected by the SCSI subsystem. Refer to the SCSI
documentation in the ServerGuide package that comes
with the server for information about these messages.
Diagnostic error messages
: Diagnostic error messages occur when a test finds a
problem with the server hardware. The messages present
text information that can be used to identify a failing part.
These error messages are alphanumeric. Follow the
instructions on the screen.
For a list of diagnostic codes, see “Symptom-to-FRU
index” on page 160.
IBM Netfinity 3000 - Type 8476
9
Software-generated error messages
: These messages occur if a problem or conflict is
found by an application program, the operating system, or
both. Error messages for operating-system and other
software problems are generally text messages, but they
also can be numeric messages. For information about
these software error messages, refer to the information
that comes with the operating system or application
program, or both.
Installing files from option diskettes
An optional device or adapter might come with a diskette.
Diskettes that are included in option packages usually
contain files that the system needs for recognizing and
activating the options. Until you install the necessary files,
the new device or adapter might cause error messages.
If the optional device or adapter comes with a diskette, you
might need to install some configuration (.CFG) files or
diagnostic files (.EXE or .COM) from the diskette to the
hard disk. Refer to the documentation that comes with the
option to see if you need to install files.
10
Netfinity Server HMM
Running the diagnostic test programs
Note
See “Diagnostic test programs” on page 7 for a
description of the diagnostic programs that come with
the server.
Attention
Do not discard the Enhanced Diagnostics Diskette.
Store it in a safe place for later use.
Make a backup copy of the IBM Enhanced Diagnostics
information on a diskette. To do this:
1. Insert a blank, 3.5-inch, formatted 2 MB diskette into
diskette drive A.
2. Use an operating-system command, such as the DOS
DISKCOPY command, to make a complete backup
copy of the Enhanced Diagnostics Diskette. Using
the backup copy can prevent damage to the original
diskette. The operating-system documentation
provides information on backing up diskettes.
3. If applicable, follow any additional instructions on the
screen.
To start the IBM Enhanced Diagnostics using the
backup Diagnostic Diskette, do the following:
1. Power-off the server and any attached devices.
2. Insert the IBM Enhanced Diagnostics backup diskette
into diskette drive A.
3. Power-on all attached devices; then, power-on the
server.
4. Follow the instructions on the screen.
Power-on self-test (POST) messages
If you receive an error message during the power-on
self-test (POST), completing the steps outlined in this
section might enable you to resolve the problem.
Note.
If you have just added, removed, or changed the
location of a device and you receive an error
message, you must reconfigure the server. Follow the
procedure described in “Configuration/Setup utility
program menus” on page 24. If the procedure in
“Configuration/Setup utility program menus” on
page 24 does not eliminate the error message, then
proceed with the following instructions.
1. Write down all error code numbers and descriptions
that appear on the screen as you start the server.
(Note that a single problem can cause several error
messages to appear. When you correct the cause of
IBM Netfinity 3000 - Type 8476
11
2.
3.
4.
5.
the first error message, the other error messages
probably will not appear on the screen the next time
that you power-on the server.)
If you have set a power-on password and have the
password prompt set to On or Dual, a password
prompt appears. If you have set both power-on and
administrator passwords, you can type either of the
passwords at the password prompt. However, if you
think you might need to change any settings in the
Configuration/Setup Utility program, you must type the
administrator password at the password prompt. If
you type the power-on password, you will be able to
view the error codes and error code descriptions that
are displayed on the POST Startup Errors screen;
you will also be able to view limited information in the
Configuration/Setup Utility program. However, you
will not be able to change any settings.
In the case of most errors, the Configuration/Setup
Utility program starts automatically so that you can
attempt to identify and correct the problem. When the
Configuration/Setup Utility program starts, a screen
titled POST Startup Errors appears. (Note that the
POST Startup Errors screen does not appear
immediately. You must wait approximately one
minute.) If the POST Startup Errors screen does not
appear, proceed to step 6 on page 13.
At the POST Startup Errors screen, select Continue
if you want to access the Configuration/Setup Utility
program menu. Select Exit Setup if you want to exit
from the Configuration/Setup Utility program. (For
more information on exiting from the
Configuration/Setup Utility program, go to the
Attention: section that follows step 5d on page 13.)
To select an item, press the Up Arrow (↑) or Down
Arrow (↓) key to highlight the item; then, press Enter.
If you selected Continue in step 4, the
Configuration/Setup Utility program menu appears on
the screen. You will see a pointer next to any menu
items that indicate components that are
malfunctioning or that have been changed since the
last time you powered-on the server. If you did not
knowingly make a change to a flagged component,
that component is probably malfunctioning. If you
made a change, continue here. If you did not make a
change, go to the Attention: section that follows step
5d on page 13.
To use the Configuration/Setup Utility program, do the
following:
a. Select the menu item that is flagged (or that you
want to view) by pressing the Up Arrow (↑) or
Down Arrow (↓) key; then, press Enter.
b. A new menu specific to the item that you
selected appears. Press the Left Arrow (←) or
Right Arrow (→) key to toggle between choices
12
Netfinity Server HMM
for a menu item. (Note that each menu item has
a Help screen. To view the Help screen, select
the menu item; then, press F1.)
c. When you have finished viewing and changing
settings, press Esc to return to the
Configuration/Setup Utility program menu.
d. Before you exit from the program, select Save
Settings. When you exit from the
Configuration/Setup Utility program menu (see
step 5e), the operating system will start
automatically (unless there is an unresolved
problem with the startup device).
Attention
If you did not change any settings in the
Configuration/Setup Utility program, note the
following:
Ÿ
Ÿ
You will get an error message if you
exit from the Configuration/Setup Utility
program without selecting Save
Settings. The operating system will
not start, but the server will
automatically restart. When the server
restarts, you will get a POST error
message, and then the
Configuration/Setup Utility program will
again start automatically.
You will not get an error message if
you select Save Settings and then exit
from the Configuration/Setup Utility
program. The system will save all
settings as they currently appear in the
Configuration/Setup Utility program,
and the operating system will start
(unless there is an unresolved problem
with the startup device).
e. To exit from the Configuration/Setup Utility
program, press Esc and follow the instructions
on the screen.
6. For more information about error messages see
“Symptom-to-FRU index” on page 160.
IBM Netfinity 3000 - Type 8476
13
Viewing the test log
Errors reported by the diagnostic test will be displayed by
the program as a failed test.
To view details of a failure or to view a list of test results,
do the following from any test category screen:
Ÿ
Ÿ
Press F3 to activate the log File
Press F3 again to save the file to diskette or F2 to
print the file.
SIMM/DIMM errors
: SIMM/DIMM error messages issued by the IBM PC
Enhanced Diagnostics:
Message
Failure Found
Recommended
Actions
2xx-1y
A memory error
was detected in
SIMM socket Y
Replace the
SIMM in the
socket identified
by the last digit of
the error code.
Re-run the test.
If the same error
code occurs
again, replace
the system
board.
2xx-2y
A memory error
was detected in
DIMM socket Y
Replace the
DIMM in the
socket identified
by the last digit of
the error code.
Re-run the test.
If the same error
code occurs
again, replace
the system board
or where memory
is on the
processor card,
replace the
processor card.
Corrupt BIOS
Information in
BIOS is not as
expected.
Not able to find
expected DMI
information from
BIOS.
Reflash the
BIOS.
Replace the
system board.
Memory controller
chipset vendor ID
does not match
expected value.
Test aborted by
user
14
User stopped
test.
Netfinity Server HMM
Restart test.
Features
The features in the server vary according to the model.
The following is a summary of the features that are
available with the Netfinity 3000 - Type 8476
Microprocessor
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Intel Pentium II microprocessor
with MMX technology
66 MHz or 100 MHz Front Side Bus (FSB)
16 KB of level-1 cache memory
512 KB of level-2 cache with error checking and correction
(ECC) memory integrated into microprocessor
Clock rate varies by model
Memory
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Three 3.3 V, synchronous, 168-pin, unbuffered, dual in-line
memory-module (DIMM) sockets
Expandable to 384 MB
100 MHz, synchronous dynamic random-access memory
(SDRAM) with error checking and correction (ECC)
Support for 32 MB, 64 MB, and 128 MB DIMMs
Flash memory for system programs
Diskette Drive
Ÿ
Ÿ
Supports one diskette drive
Standard: One 3.5-inch, 1.44 MB
Hard Disk Drives
Ÿ
Ÿ
Number and capacities of hard disk drives vary by model
Server supports up to four internal hard disk drives
CD-ROM Drive
Ÿ
Standard: IDE
Keyboard and Auxiliary Device
Ÿ
Ÿ
Keyboard
Mouse
Expansion Slot Connectors
Supports up to seven adapters:
Ÿ
Ÿ
Ÿ
Three dedicated ISA slot connectors
Three dedicated PCI slot connectors
One dedicated Accelerated Graphics Port (AGP) slot
connector
Expansion Bays
Ÿ
Ÿ
Ÿ
Ÿ
One 3.5-inch or 5.25-inch drive bay
Four 3.5-inch drive bays
Number of bays available for expansion varies by model
Standard: One dedicated 5.25-inch drive bay for CD-ROM
drive
Upgradable POST and BIOS
Ÿ
POST/BIOS upgrades (when available) to update EEPROM
on the system board
Security Features
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Bolt-down capability
Chassis-intrusion detector
Power-on and administrator passwords
Security-error indicator
Selectable drive-startup sequence
IBM Netfinity 3000 - Type 8476
15
Ÿ
Ÿ
Side cover lock
Unattended start mode
SCSI Features
Ÿ
Ÿ
16-bit UltraSCSI adapter
– One external connector
– One internal connector
Four bays available for internal SCSI hard disk drives
Power Supply
Ÿ
Ÿ
Ÿ
330 Watts
Auto-sensing function
Built-in overload and surge protection
Integrated Functions
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
16
Voltage regulator for microprocessor
Two serial ports
Two universal serial bus (USB) ports
One parallel port
Mouse port
Keyboard port
Full-duplex 10/100 Mbps Ethernet controller
– 10BASE-T/100BASE-TX port
– Integrated Direct Memory Access (DMA) Buffer
Management Unit for low microprocessor and bus
utilization
AGP function on system board
– 4 MB synchronous graphics random-access memory
(SGRAM), 100 MHz
One dedicated AGP slot connector for video adapter
Wake on LAN capability
Alert on LAN capability
Systems Management Controller
Netfinity Server HMM
Additional service information
The following additional service information supports
Netfinity 3000 - Type 8476 server.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
“Configuration overview” on page 18.
“Configuration conflicts” on page 20.
“Configuration/Setup utility program” on page 21.
“Configuration/Setup utility program menus” on
page 24.
“Configuring the Ethernet controller” on page 38.
“Erasing lost or forgotten passwords” on page 42.
“Power supply” on page 45.
“ROM operation mode switch setting” on page 47.
“SCSISelect utility program” on page 49.
“Specifications (Ethernet cable)” on page 53.
“Specifications (system)” on page 56.
IBM Netfinity 3000 - Type 8476
17
Configuration overview
You play a key role in how the server allocates resources
to organize and interconnect hardware devices and
software programs. This allocation process is referred to
as configuration. The steps required to configure the
server depend on the number and types of devices and
programs that you install.
The server has connectors for several types of adapters.
Because of this flexibility, you can choose from among
thousands of adapters and devices that comply with any of
the following standards:
Ÿ
Ÿ
Ÿ
Ÿ
Peripheral Component Interconnect (PCI)
Industry Standard Architecture (ISA)
Small Computer System Interface (SCSI)
Accelerated Graphics Port (AGP)
You can obtain a listing of products that are compatible
with the server, and related configuration information, by
accessing the following World Wide Web address:
http://www.ibm.com/pc/us/compat/
Jumpers and switches are used to define certain
configuration values on the system board, adapters, and
other devices. If you need to set jumpers or switches on
adapters, drives, or other devices, refer to the
documentation that comes with the devices for specific
information about the appropriate jumper and switch
settings.
In general, the greater the number and variety of hardware
devices and software programs that you install in the
server, the more you will have to interact with the server
and the devices to correctly configure the system.
The server comes with the following hardware
configuration utility programs:
Ÿ
Configuration/Setup Utility program
Ÿ
With the Configuration/Setup Utility program, you can
configure system board functions, such as serial and
parallel port assignments; change interrupt request
settings, and change the startup sequence for drives
that you install. You can also use this utility program
to set passwords for starting the server and accessing
the Configuration/Setup Utility program.
SCSISelect Utility
With the built-in SCSISelect Utility program, you can
configure the SCSI devices that you install in the
server. You can use SCSISelect to change default
values, resolve configuration conflicts, and perform a
low-level format on a SCSI hard disk drive.
Before installing a new device or program, read the
documentation that comes with it. Reading the instructions
18
Netfinity Server HMM
helps you to determine the steps required for installation
and configuration. The following actions are typically, but
not always, required to configure the server.
1. Run the Configuration/Setup Utility program and
record the current configuration settings.
See “Configuration/Setup utility program” on page 21.
2. Set jumpers or switches on the server's system
board.
3. Set jumpers or switches on the device.
See the device installation instructions.
4. Install the device in the server.
Reserve ISA legacy resources for ISA adapters. See
“ISA legacy resources” on page 36.
5. Resolve configuration conflicts.
See “Configuration conflicts” on page 20.
6. Install software programs, including device drivers.
Refer to the information that comes with the IBM
ServerGuide package for more information.
IBM Netfinity 3000 - Type 8476
19
Configuration conflicts
The resources used by the server consist of IRQs, DMA,
I/O port addresses, and memory. This information is
useful when a resource configuration conflict occurs.
Conflicts in the configuration occur if:
Ÿ
Ÿ
Ÿ
Ÿ
A device that you installed requires the same
resource as another device. (For example, a conflict
occurs when two adapters try to write to the same
address space.)
A device resource is changed (for example, changing
jumper settings).
A device function is changed (for example, assigning
COM1 to two serial ports).
A software program is installed that requires the same
resource as a hardware device.
The steps required to resolve a configuration error are
determined by the number and variety of hardware devices
and software programs that you install. If a hardware
configuration error is detected, a configuration error
message appears after the server completes POST and
before the operating system is loaded. You can bypass
the error by pressing Esc while the error message is
displayed.
The Configuration/Setup Utility program configures only the
system hardware and interrupt requests. The program
does not consider the requirements of the operating
system or the application programs. For these reasons,
memory-address configuration conflicts might occur. You
can resolve some memory-address conflicts by changing
the address of the conflicting hardware option, or by
changing or moving the hardware. You might have to
resolve other memory-address conflicts by changing some
software parameters. See “Hardware configuration
conflicts” and “Software configuration conflicts” on
page 21, respectively, for additional information.
Hardware configuration conflicts
: Use the following information to help resolve hardware
configuration conflicts:
1. Run the Configuration/Setup Utility program to view
and change the resources that the system board
functions use. Record the current settings before
making any changes. (See “Configuration/Setup
utility program” on page 21 for instructions.)
2. Determine which adapter or device is causing the
conflict.
3. Change adapter jumpers or switches. Some devices
use jumpers and switches to define the system
resources that they need. If the settings are incorrect
or set to use a resource that cannot be shared, a
20
Netfinity Server HMM
conflict occurs, and the device will remain deactivated
by the configuration program.
4. Change system board jumpers or switches. Then,
refer to the system board diagram inside the server.
5. Remove the device or adapter. Some configurations
are not supported. If you must remove an adapter,
see “Installing or removing ISA and PCI adapters” on
page 62.
Software configuration conflicts
: The Configuration/Setup utility might change the
memory-address space used by some hardware options.
If this happens, the new memory-address space and IRQs
used by some hardware options might conflict with
addresses defined for use through application programs.
If a conflict exists, one or more of the following conditions
might exist:
Ÿ
Ÿ
Ÿ
Ÿ
The system cannot load the operating system.
The system does not work.
An application program does not operate, or it returns
an error.
Screen messages indicate that a memory-address
conflict exists.
Note
Start the Configuration/Setup Utility program to view
the addresses that are used by the system board
functions.
The best way to resolve memory-address conflicts is to
change the addresses that are used by the application
program or the device driver. You can use the
Configuration/Setup Utility program to view and change
addresses.
Configuration/Setup utility program
For most configurations, the server will operate using the
default system settings. You need to change the settings
only to resolve configuration conflicts or to enable or
change device functions.
When you want or need to change the default settings, the
Configuration/Setup Utility program provides a convenient
way to display and change the settings.
After you run and exit the Configuration/Setup Utility
program, configuration information is stored in electrically
erasable programmable read-only memory (EEPROM).
While the server is powered off, the configuration
information remains available for the next system startup.
Always run the Configuration/Setup Utility program if you
receive an error message instructing you to do so. If you
installed or removed SCSI devices, run the SCSISelect
IBM Netfinity 3000 - Type 8476
21
Utility program (see “SCSISelect utility program” on
page 49). Review the information that comes with the
option before making changes.
When you restart the server for the first time after working
with most options, a message appears, indicating that a
configuration change has occurred. You are then
prompted to enter the Configuration/Setup Utility program
to manually update the configuration settings or to confirm
and save the settings that were automatically updated by
the system programs.
After you change an option and restart the server, the
following screen might appear.
POST Startup Error(s)
The following error(s) were detected when the system was
started:
162 Configuration Change Has Occurred
Select one of the following:
Continue
Exit Setup
Note
Depending on the configuration changes that
occurred, the error message that you see might be
different from the one shown here.
If the preceding screen appears, select Continue until you
reach the Configuration/Setup Utility program menu; then,
go to “Configuration/Setup utility program menus” on
page 24.
If the preceding screen does not appear, use the following
procedures to access the Configuration/Setup Utility
program menu.
To start the Configuration/Setup Utility program:
1. Power-on the server and watch the screen.
If the server is already turned on, power-off the
server, wait a few seconds until all in-use lights go
off, and then power the server back on. (Do not use
Ctrl+Alt+Del to restart the server.)
2. When the message Press F1 to enter
Configuration/Setup appears, press F1. The
Configuration/Setup Utility program menu appears.
For information about the menus, see
“Configuration/Setup utility program menus” on
page 24.
22
Netfinity Server HMM
Notes
1. If an administrator password is not set, the
Configuration/Setup Utility program starts once
you complete the startup procedure.
2. If an administrator password is set, but a
power-on password is not set, you must enter the
administrator password to access the
Configuration/Setup Utility program.
3. If you have set both an administrator and a
power-on password, you can enter either one.
However, to change any settings in the
Configuration/Setup Utility program, you must
enter the administrator password. If you enter
the power-on password, you can view limited
information in the Configuration/Setup Utility
program, but you cannot change any settings.
4. If a configuration error occurs, a prompt appears
before the operating system starts ( see
“Configuration conflicts” on page 20).
IBM Netfinity 3000 - Type 8476
23
Configuration/Setup utility program
menus
From the Configuration/Setup Utility program Main Menu,
you can select the settings that you want to change.
Configuration/Setup Utility
Select Option:
• System Summary
• Product Data
• Devices and I/O Ports
• Start Options
• Date and Time
• System Security
• Advanced Setup
• ISA Legacy Resources
• Power Management
Save Settings
Restore Settings
Load Default Settings
Exit Setup
<F1> Help
<Esc> Exit
<↑> <↓> Move
<Enter> Select
Note
The menu that you see on the server screen might
look slightly different from the menu shown here, but it
will operate the same way.
Pressing F1 displays Help information for a selected menu
item.
In the Configuration/Setup Utility program menus, you can
accept the configuration changes by viewing and saving
the changes, or you can make manual changes and then
save the settings.
The following is a quick reference for identifying symbols in
the Configuration/Setup Utility program.
Ÿ
Ÿ
Ÿ
Ÿ
A bullet (Ÿ) beside a menu item indicates that an
additional menu is available.
Information enclosed in brackets ([ ]) can be changed.
You cannot change information that is not surrounded
by [ ].
A right arrowhead (5) beside a menu item indicates
that a configuration change occurred in that category.
The 5 might also appear in subsequent menus.
An asterisk (*) beside a menu item indicates that a
resource conflict exists.
To exit from the Configuration/Setup Utility program:
1. From the Configuration/Setup Utility program, select
Exit Setup or press Esc.
2. The Exit Setup menu appears. You can save the
changes, exit from the Configuration/Setup Utility
program without saving the changes, or return to the
24
Netfinity Server HMM
Configuration/Setup Utility program menu. Use the
arrow keys to select the desired option; then, press
Enter.
Note
The choices on some menus might differ slightly,
depending on the BIOS version that comes with the
server.
Use the following commands to navigate through the
screens and make selections:
Key
↑
Function
↓
←
→
Move between menu items.
Toggle between choices for a menu item.
Enter
Select an item.
Esc
Exit from a menu after viewing or making changes.
F1
Get help on a selected menu item.
System summary
: Select this choice to display configuration information,
such as the type and speed of the microprocessor, and the
amount of memory.
Changes that you make to configuration settings appear on
this summary screen. You cannot edit the fields on this
screen. If you need to change the configuration settings,
you must make the changes from the applicable menu
choices.
Product data
: Select this choice to view the machine type and
model, the system serial number, the system board
identifier, and the revision level or issue date of the flash
EEPROM (BIOS).
Devices and I/O ports
: Software recognizes ports from their port assignments.
Each port must have a unique port assignment. The
Configuration/Setup Utility program normally handles this,
but you might have special hardware or software that
requires you to change these assignments.
Select the Devices and I/O Ports choice to view or
change the assignments for devices and input/output ports.
IBM Netfinity 3000 - Type 8476
25
You can add serial ports by installing a serial adapter in an
expansion slot. See the documentation that comes with
the serial adapter for information about port assignments.
To display or change the port assignments:
1. From the Configuration/Setup Utility program menu,
select Devices and I/O Ports.; then, press Enter.
2. The Devices and I/O Ports menu appears.
3. Select a device or port. If necessary, press Enter to
display an additional menu.
4. Use the Left Arrow (←) or Right Arrow (→) key to
advance through the settings.
Start options
: Select this choice to view and change settings for
device startup sequence, keyboard speed, virus detection,
various power-on options, and other features.
You can control the startup sequence of the devices in the
server. Each time that you power-on the server, it checks
the devices as it looks for the operating system. The order
in which the system checks the devices is the
device-startup sequence.
Note
The default startup sequence is:
1. CD-ROM drive
2. Diskette drive
3. Hard disk drive
To set the startup sequence:
1. From the Configuration/Setup Utility program menu,
select Start Options; then, press Enter.
2. The Start Options menu appears.
3. Select Startup Sequence; then, press Enter.
4. Select the sequence and devices from the choices
provided.
5. If Automatic Power On Startup Sequence is
Enabled, select the sequence and devices from the
choices provided.
To set the power-on status:
1. From the Configuration/Setup Utility program menu,
select Start Options; then, press Enter.
2. The Start Options menu appears.
3. Select Startup Sequence; then, press Enter.
4. Select Power-on Status.
5. Select the power-on status from the choices provided.
Date and time
: Select this choice to set the system date and time.
The system time is in a 24-hour format:
hour/minute/second. The system date is in standard
26
Netfinity Server HMM
format for your country or region. For example, in the
United States, the format is MM/DD/YYYY
(Month/Day/Year).
To set the date and time:
1. From the Configuration/Setup Utility program menu,
select Date and Time; then, press Enter.
2. The Date and Time menu appears.
3. Use the Left Arrow (←) or Right Arrow (→) key to
advance through each data field.
4. Type the new information; the system saves the
information as you enter it.
System security
: Several security features are available to help you
secure the server and the information that you store in it.
To control access to the server, you can implement the
security features, such as adding passwords, and securing
IDE devices and diskette drives.
Setting power-on password modes
: The power-on password can deter unauthorized
access to the system. You do not need to set a power-on
password, but doing so allows you to control who can use
the server. When a power-on password is set, you must
type the password at a prompt that appears as the server
starts.
When you set the power-on password, you can choose
one of three password prompt modes.
On
In password prompt On mode, you are prompted for
the power-on password when you power-on the
server. Until you enter the correct password, the
operating system will not start, and the keyboard will
remain locked. If you have a mouse connected to the
mouse port, the mouse also will remain locked until
you enter the power-on password. If you have a
mouse connected to a serial port, it will be activated
when the server is started, regardless of whether a
password is set.
Note
If Remote Administration is enabled, you
cannot select On. In this case, select Dual. If
the power-on password mode is set to On when
Remote Administration is enabled, it resets
automatically to Dual.
Off
In password prompt Off mode (sometimes referred to
as unattended start mode), you are not prompted to
enter the power-on password when you power-on the
server. The server will start the operating system.
IBM Netfinity 3000 - Type 8476
27
However, if you have a mouse connected to the
mouse port, refer to the following text box.
Important Information for Mouse Users
This information applies only to those who have a
mouse connected to the mouse port; a serial
mouse is not affected by the password prompt
Off mode.
The password prompt Off mode prevents the
server from detecting that a mouse is attached.
Because in this mode, the mouse device driver
will not be loaded automatically through the
CONFIG.SYS or AUTOEXEC.BAT files, an error
message will appear to indicate that the mouse
port is disabled, and the server will halt. To
enable the operating system to load without
displaying the error message, follow the
instructions that apply to the operating system.
If you are using OS/2, do one of the following
before enabling password prompt Off mode:
Ÿ
Ÿ
Set the CONFIG.SYS file so that the
operating system does not stop on a
device-driver error. To do this, put the
command PAUSEONERROR=NO near the
top of the CONFIG.SYS file.
or
Remove the mouse driver statement from
the CONFIG.SYS file.
If you are using Windows NT or Windows 95, do
the following:
Ÿ
When the server is started and the mouse
port disabled error message appears, type
either the power-on or administrator
password to enable the keyboard. Then use
the keyboard to put a check mark in the Do
not display this message in the future
check box.
Once the operating system starts in password prompt
Off mode, the keyboard will remain locked. If you
have a mouse connected to the mouse port, it also
will remain locked.
Although you are not prompted to type a password in
this mode, you can type either the power-on or
administrator password anytime after POST has
completed, even after the operating system has
loaded. If you type a password, the keyboard will
unlock, but the mouse connected to the mouse port
will remain disabled.
Password prompt Off mode is useful for network
servers and other servers that operate unattended. If
a power failure occurs, the server will automatically
28
Netfinity Server HMM
restart and resume operating in this mode when
power is restored, without operator intervention.
If you enter a password, the keyboard will unlock, but
the mouse connected to the mouse port will remain
disabled.
Password prompt Off mode is useful for network
environments that cause the server to operate
unattended. If a power failure occurs, when power is
restored, the server will automatically restart and
resume operating in this mode, without operator
intervention.
Dual
In the password prompt Dual mode, the startup
behavior of the server depends on whether the server
is started from the server power switch or by an
unattended method, such as a modem or timer.
If you press the power switch to start the server, the
server operates the same as it does in password
prompt On mode.
If you start the server by an unattended method, such
as remotely over a LAN, the server operates in
password prompt Off mode.
If both a power-on and administrator password are set, you
can type either password at the password prompt that
appears as you start the server. However, if you want to
change any settings in the Configuration/Setup Utility
program, you must type the administrator password at the
password prompt that appears when you try to access the
Configuration/Setup Utility program. If you type the
power-on password at this prompt, you will be able to view
limited information in the Configuration/Setup Utility
program, but you will not be able to change any settings.
The password does not appear on the screen as you type
it. If you type the wrong password, you receive a screen
message telling you so. If you type the wrong password
three times, you must power the server off and start again.
When you type the correct password, the keyboard and
mouse will unlock, and the server will begin normal
operation.
Setting and changing a power-on password
: Use the Configuration/Setup Utility program to set or
change a power-on password.
IBM Netfinity 3000 - Type 8476
29
Attention
Keep a record of the power-on password in a secure
place. When a power-on password has been set, you
cannot activate the keyboard and mouse without first
using the password. If you lose or forget the
password, you cannot change or delete it without
removing the server cover and moving a jumper on
the system board. See “Erasing lost or forgotten
passwords” on page 42 for further information.
To set or change a power-on password:
1. From the Configuration/Setup Utility program menu,
select System Security; then, press Enter.
2. The System Security menu appears.
3. Select Power-On Password; then, press Enter.
4. The Power-On Password menu appears.
5. To set a power-on password, enter the password in
the appropriate data field and press the Down Arrow
(↓) key.
You can use any combination of up to seven
characters (A–Z, a–z, and 0–9) for this password.
Keep a record of the password in a safe place.
6. Enter the password again in the appropriate data
field.
7. In the Password Prompt data field, select Off, On,
or Dual. Press the Left Arrow (←) or Right Arrow (→)
key to toggle among selections.
Note
If Remote Administration is enabled, you
cannot select On. In this case, select Dual. If
the power-on password mode is set to On when
Remote Administration is enabled, it resets
automatically to Dual.
8. To change a power-on password, select Change
Power-On Password from the Power-On Password
menu, and follow the instructions on the screen.
Notes
1. If a power-on password is set and then forgotten,
you must remove the server cover and move the
Clear CMOS Request jumper on the system
board. (See “Erasing lost or forgotten
passwords” on page 42 for further information.)
2. If a power-on password is set and the password
prompt is set to Off, the pointing device (mouse)
is disabled until you enter the power-on
password.
To delete a power-on password:
30
Netfinity Server HMM
1. From the Configuration/Setup Utility program menu,
select System Security; then, press Enter.
2. The System Security menu appears.
3. Select Power-On Password; then, press Enter.
4. The Power-On Password menu appears.
5. Select Delete Power-On Password and follow the
instructions on the screen.
Using the administrator password menu
: The administrator password (sometimes called a
supervisor-level password) controls access to some
features of the server, including the Configuration/Setup
Utility program.
To set or change an administrator password:
1. From the Configuration/Setup Utility program menu,
select System Security; then, press Enter.
2. The System Security menu appears.
3. Select Administrator Password; then, press Enter.
4. The Administrator Password menu appears.
5. To set an administrator password, enter the password
in the appropriate data field and press the Down
Arrow (↓) key.
You can use any combination of up to seven
characters (A–Z, a–z, and 0–9) for this password.
Keep a record of the password in a safe place.
6. Enter the password again in the appropriate data
field,
7. Define the Power-On Password Changeable by
User field. The choices are:
Yes
The power-on password can be changed
without entering the administrator password, if
the administrator password is set.
No
The power-on password cannot be changed
unless the administrator password is entered, if
the administrator password is set.
8. To change an administrator password, select Change
Administrator Password from the Administrator
Password menu, and follow the instructions on the
screen.
Attention Administrator Password Users:
If an administrator password is set and then forgotten,
you must complete one of the following to regain
access to the Configuration/Setup Utility program:
Ÿ
Ÿ
If enhanced security is disabled (default setting),
you must remove the server cover and move the
Clear CMOS Request jumper on the system
board. (See “Erasing lost or forgotten
passwords” on page 42 for further information.)
If enhanced security is enabled, you must replace
the system board.
IBM Netfinity 3000 - Type 8476
31
To delete an administrator password:
1. From the Configuration/Setup Utility program menu,
select System Security; then, press Enter.
2. The System Security menu appears.
3. Select Administrator Password; then, press Enter.
4. The Administrator Password menu appears.
5. Select Administrator Password.
6. Select Delete Administrator Password and follow
the instructions on the screen.
If both a power-on and administrator password are set, you
can enter either password to complete the system startup.
However, the administrator password provides access to
all menu choices, and provides the ability to change
information. If you enter the power-on password, you can
view limited information in the Configuration/Setup Utility
program, but you cannot change any settings.
Using the enhanced security features
: With enhanced security, the administrator password
and drive-startup sequence are stored in a highly
protected, nonvolatile, security EEPROM module. When
the administrator password and drive-startup sequence are
stored in the security EEPROM, they remain intact even if
the battery expires or is removed.
Attention Administrator Password Users:
If enhanced security is enabled, and you forget or lose
the administrator password, you must replace the
system board in the server to regain access to the
Configuration/Setup Utility program.
If enhanced security is enabled and you have set an
administrator password, the server will operate as follows:
Ÿ
The security EEPROM is protected from unauthorized
access once the startup procedures are complete.
With enhanced security disabled, the contents of the
EEPROM are write protected, and the server can
function in a network environment because the
POST/BIOS utility program will allow updates to the
system programs.
Ÿ
With enhanced security enabled, the POST/BIOS
utility program will not allow updates to the system
programs. In a network environment, this might
prevent certain functions from being performed
remotely.
If the cover of the server has been removed, a
tamper-detection feature will halt system processing
and deny access to the keyboard and mouse until the
administrator password is entered. This feature will
work if the server is powered on or off.
To enable or disable enhanced security:
32
Netfinity Server HMM
Note
Enhanced security can be enabled or disabled only
when you update the system programs in the server.
1. Insert a system programs update diskette in the
server. System programs updates are available on
the World Wide Web. To obtain up-to-date
information about the server model, access the home
page for the server at the following address:
http://www.ibm.com/pc/us/netfinity/
2. Power-on the server. If it is already powered on, you
must power it off and back on again.
3. The update begins, and the system prompts you for
the administrator password, if you have set an
administrator password.
4. When you enter the administrator password, the
update diskette will continue to run, and you are given
the option of enabling or disabling enhanced security.
To set, change, or delete an administrator password
protected by enhanced security:
1. Power-off all attached devices and the server.
2. Disconnecting all cables, and removing the server
cover.
3. Locate the switch marked as 7 on the rocker switches
section of the system board. See “Administrator
password switch setting” on page 145 for the location
of the switch. Move the switch to the ON position. (It
might be helpful to use the end of a small screwdriver
to set the switch.)
Note
You must know the administrator password to
change or delete it.
4. Set, change, or delete the password. Follow the
instructions on the screen. (See “Using the
administrator password menu” on page 31.)
5. Move the switch back to the OFF position after you
have set, changed, or deleted the password.
6. Replace the cover. Then, power-on the server.
Restricting access to IDE devices and diskette
drives
: The setting for the Secure IDE and Diskette Drives
option controls who has access to the IDE devices and
diskette drives (user and administrator, or administrator
only). The server comes with this feature set to Enable,
so that both the user and administrator have access to the
IDE devices and diskette drives.
To disable access to the IDE devices and diskette
drives:
IBM Netfinity 3000 - Type 8476
33
1. From the Configuration/Setup Utility program menu,
select System Security; then, press Enter.
2. The System Security menu appears.
3. Select Secure IDE Devices and Diskette Drives;
then, press Enter.
4. Select a device; then, press the Left Arrow (←) or
Right Arrow (→) key to toggle the entry to Disable.
Note
The server supports IDE CD-ROM drives. IDE hard
disk drives are not supported.
Remote administration
: Using this option, the BIOS can be updated remotely
from a network server. If an administrator password is set,
it does not have to be entered from the server to access
this function. Consult the network administrator for
information on setting up the network server to perform
POST and BIOS updates.
To access the Remote Administration setting:
1. From the Configuration/Setup Utility program menu,
select System Security; then, press Enter.
2. The System Security menu appears.
3. Select Remote Administration; then, press Enter.
4. To enable update POST/BIOS over the network,
select Enabled (default setting). To disable, select
Disabled.
You might need to perform a POST/BIOS (flash) update
under the following circumstances:
Ÿ
Ÿ
Ÿ
Ÿ
When you receive a system message instructing you
to do so
When you install a new microprocessor (see
“Microprocessors” on page 130)
When you receive an error code (see
“Symptom-to-FRU index” on page 160)
When you change certain configuration switch
settings (see “Microprocessor speed switches
settings” on page 153 and “ROM operation mode
switch setting” on page 47)
Before you can perform a POST/BIOS (flash) update, you
must create a Flash Utility Diskette, as follows:
1. Insert a blank, 3.5-inch, formatted 2 MB diskette into
diskette drive A.
2. Go to http://www.ibm.com/support/ on the World Wide
Web and download the appropriate flash update
program. Review the applicable README files, and
use this information to copy the Flash Utility program
onto the diskette.
3. If applicable, follow any additional instructions on the
screen.
34
Netfinity Server HMM
Note
The server is shipped with the Remote
Administration feature set to Enabled. To ensure
that the POST/BIOS update (flash) procedure works
properly, do not change this default value.
To perform a POST/BIOS (flash) update, insert the Flash
Utility Diskette into the primary diskette drive and run the
Flash Utility program. Follow the instructions in the
program.
Setting Adapter ROM security
: Use this setting to lock the keyboard during adapter
read-only memory (ROM) initialization; this feature can be
used in conjunction with an administrator password to
prevent the use of adapter ROM-based utility programs.
Advanced setup
: Select Advanced Setup to change values for
advanced hardware features, such as cache control, ROM
shadowing, PCI control, Plug and Play control, and
microprocessor control.
Attention
The system might not operate properly if these options
are configured incorrectly. Follow the instructions on
the screen carefully.
Use the Left Arrow (←) or Right Arrow (→) key to select a
menu choice.
Cache control
: Select this choice to define the microprocessor cache
state as enabled or disabled.
ROM shadowing
: Select this choice to enable or disable ROM
shadowing in specified areas. When these areas are
enabled, the contents can be cached, using the Cache
Control option. These areas are hexadecimal address
ranges. One of these areas is reserved for the system
BIOS address space.
PCI control
: Select this choice to control features associated with
PCI devices, such as PCI Adapter Reset, PCI Parity, PCI
Bus Master, Multimedia Devices, and various types of
adapters.
Plug and Play control
: Select this choice to control features associated with
Plug and Play devices, such as Set Device Node,
Address Decode, and Plug and Play Operating System.
IBM Netfinity 3000 - Type 8476
35
Select Set Device Node to control the device node. When
you change this value to Disabled, the system cannot
update the configuration during POST.
Processor control
: Select this choice to control features associated with
the microprocessors, such as Processor 0 ID and
Processor Updating.
ISA legacy resources
: Plug and Play is a configuration method that makes
expanding the server easier. Support for Plug and Play is
built into the system board of the server.
If an adapter is Plug and Play, there are no switches or
jumpers that must be set on the adapter. A Plug and Play
adapter comes with configuration specifications set in
memory to provide installation information to the server
during startup. When you install or remove Plug and Play
adapters, this information is interpreted by the BIOS, which
supports Plug and Play technology. If the required
resources are available, the BIOS software automatically
configures the adapter around the resources already in use
by other devices.
Most adapters designed for PCI slots are Plug and Play
devices that are auto-configuring. However, many ISA
adapters are not Plug and Play devices. These adapters
are known as legacy adapters. If you install a legacy
adapter, you must manually configure it by setting switches
or jumpers on the adapter, and by allocating or reserving
the system resources that the adapter will use.
Note
See “Configuration conflicts” on page 20 for
information about handling resource conflicts.
Select ISA Legacy Resources to identify the available
system resources:
Ÿ
Ÿ
Ÿ
Ÿ
Memory
I/O ports
DMA
Interrupt
Note
The menus do not contain resources that are used by
the system or by previously installed Plug and Play
adapters.
To store the legacy resource information for an
installed adapter:
36
Netfinity Server HMM
1. Select ISA Legacy Resources; then, use the Up
Arrow (↑) or Down Arrow (↓) key to highlight the
system resource that you want to change.
2. Select a resource; then, use the Left Arrow (←) or
Right Arrow (→) key to select a configuration choice.
If you remove an ISA legacy adapter, you must redefine
the system resource as [Available].
Power management
: With Power Management, the server and monitor can
be set to use a reduced-power state if they are inactive for
a specified length of time. You can also specify options to
automatically start the server.
Attention
The ACPI BIOS Mode feature is the only available
Power Management feature.
The APM BIOS Mode feature is set to Disabled. Do not
change this default value.
Using the Automatic configuration and power
interface BIOS mode
: When the automatic configuration and power interface
(ACPI) BIOS mode is enabled, the operating system
controls the power management features of the server and
the settings for APM BIOS mode are ignored. Refer to the
operating-system documentation to determine if the
operating system supports ACPI. If the operating system
does not support ACPI, you cannot use the ACPI BIOS
Mode Power Management feature.
To set ACPI BIOS mode:
1. Select Power Management from the
Configuration/Setup Utility program menu.
2. Set ACPI BIOS Mode to Enabled or Disabled as
desired using the Left Arrow (←) or Right Arrow (→)
key.
IBM Netfinity 3000 - Type 8476
37
Configuring the Ethernet controller
The Netfinity 3000 server comes with an Ethernet
controller on the system board. The Ethernet controller
provides 10BASE-T and 100BASE-TX support through the
RJ-45 connector on the back of the server. When you
connect the server to the network, the Ethernet controller
automatically detects the data-transfer rate (10 Mbps or
100 Mbps) on the network and then sets the controller to
operate at the appropriate rate. That is, the Ethernet
controller will adjust to the network data rate, whether the
data rate is standard Ethernet (10BASE-T), Fast Ethernet
(100BASE-TX), half duplex (HDX), or full duplex (FDX).
This process is also known as auto-negotiation. This
auto-negotiation occurs without requiring software
intervention. The controller supports half-duplex (HDX)
and full-duplex (FDX) modes at both speeds.
However, auto-negotiation works only if the hub or switch
to which the server is connected also supports
auto-negotiation. If the hub or switch does not support
auto-negotiation, the speed (10 Mbps or 100 Mbps) will still
be detected correctly, but half-duplex mode will always be
selected. A full-duplex switch that does not support
auto-negotiation will not attach to the Netfinity 3000 server
in full-duplex mode. In this case, if you want the network
to operate in full-duplex mode, you must manually override
the settings to obtain a full-duplex connection. To do this,
the server must have a device driver that supports manual
overrides. Use ServerGuide to install this device driver.
Refer to the ServerGuide package for instructions on
installing device drivers. ServerGuide includes IBM
Update Connector, which keeps the BIOS and device
drivers current. Verify that you have installed the
appropriate device driver. Also, refer to the Ethernet
documentation for additional information on operating
modes, manual overrides, and device drivers.
Attention
Ÿ
Ÿ
The 10BASE-T Ethernet and the 100BASE-TX
Fast Ethernet cabling in the network must be
Category 5 to meet various standards, including
electromagnetic compatibility.
You must install a device driver to enable the
operating system to address the Ethernet
controller. Use ServerGuide to install this device
driver. Refer to the ServerGuide package for
instructions on installing device drivers.
Fast Ethernet operates at a data rate of up to 100 Mbps.
However, except for the different operating speeds, Fast
Ethernet and standard Ethernet are structurally identical.
Most applications and protocols that are currently installed
on a standard Ethernet system can be seamlessly
migrated to a Fast Ethernet system. Because of the
38
Netfinity Server HMM
equivalence of the two types of Ethernet, mixed Ethernet
and Fast Ethernet systems also can be designed and
implemented.
The bandwidth required at each workstation connected to
a server is generally far less than the bandwidth required
at the server. This is because the server might have to
handle the bandwidth of multiple workstations at the same
time. A cost-effective solution to the bandwidth
requirements of this type of system is a mixed Ethernet
and Fast Ethernet network. This mixed network consists
of standard Ethernet connections at the workstations and
Fast Ethernet connections at the servers.
The Ethernet controller is a PCI device, and is therefore a
Plug and Play device. You do not have to set any jumpers
or configure the controller for the operating system before
you use the Ethernet controller.
Notes
1. For information on Ethernet indicators, see
“Controls and indicators” on page 81.
2. For information on the Ethernet connector, see
“Input/Output connectors” on page 94 and
“Ethernet connector” on page 159.
3. For troubleshooting information, see
“Troubleshooting the 10/100 Mbps Ethernet
Controller” on page 40.
4. The Ethernet controller supports the operating
systems that the server supports. To find out
which operating systems the server supports, go
to the following World Wide Web address:
http://www.ibm.com/pc/us/netfinity/
If you need additional Ethernet connections, you can install
an Ethernet adapter, such as an IBM 10/100 Ethernet
adapter. Review the network-adapter documentation for
any additional configuration requirements.
Note
If you are installing an IBM 10/100 Ethernet adapter,
be sure to run the Ethernet controller diagnostics and
record the server's Ethernet controller configuration
information before you install the adapter.
IBM Netfinity 3000 - Type 8476
39
Troubleshooting the 10/100 Mbps Ethernet
Controller: Use the following information to help
isolate problems that might occur with the 10/100 Mbps
Ethernet controller.
Note
For additional information about the Ethernet
controller, such as configuration and auto-negotiation,
see “Configuring the Ethernet controller” on page 38.
For an illustration of the Ethernet activity light location
on the server, see “Status indicators” on page 82.
Network connection problems: If the Ethernet
controller cannot connect to the network, check the
following:
1. Make sure that the cable is installed correctly.
The network cable must be securely attached at all
connections. If the cable is attached but the problem
persists, try a different cable.
If you use the integrated Ethernet controller, you must
use Category 5 cabling. See “Specifications
(Ethernet cable)” on page 53 for additional
information about Ethernet cable requirements.
If you directly connect two workstations (without a
hub), or if you are not using a hub with X ports, use a
crossover cable. See “Specifications (Ethernet
cable)” on page 53 for an illustration of a crossover
cable.
Note
To determine whether a hub has an X port,
check the port label. If the label contains an X,
the hub has an X port.
2. Check the Ethernet activity light on the front of the
server.
The Ethernet activity light comes on when the
Ethernet controller sends or receives data over the
Ethernet network.
Note
This light is off when you run the diagnostic
programs in the Configuration/Setup Utility
program.
40
Netfinity Server HMM
If the Ethernet activity light is off:
a. Make sure that the hub and network are
operating, and that the correct device drivers are
loaded.
b. There might be a defective Ethernet connector or
cable, or a problem with the hub.
3. Make sure that you are using the correct device
drivers that come with the server.
4. Check for operating system-specific causes for the
problem.
5. Test the Ethernet controller or adapter.
How you test the Ethernet controller or adapter
depends on which operating system you are using.
Refer to the serverGuide documentation for details
about the operating system.
Diagnostic LEDs: The server contains two diagnostic
LEDs (one green, and one amber) on the Ethernet
connector that is located at the rear of the server.
Ÿ
When the green LED is on, it indicates that the
Ethernet controller or adapter is connected to a hub
or switch and is receiving link pulses. If this LED is
not on, check all connections at the controller or
adapter and the hub. Make sure that the hub is
transmitting at the correct speed, and that the drivers
are loaded.
Also, make sure that you have the correct wiring
configuration for the controller or adapter to the hub
connection. Some hubs require a crossover cable
rather than a straight-through cable.
Notes
1. This LED is also known as the Link OK light.
2. The green LED is on when you run the
diagnostics loopback test without a cable
attached to the controller or adapter.
Ÿ
When the amber LED is on, it indicates that the
Ethernet network is operating at 100 Mbps. When
this LED is off, it indicates that the Ethernet network
is operating at 10 Mbps.
Note
The amber LED might remain lit if the link is
broken during activity.
IBM Netfinity 3000 - Type 8476
41
Erasing lost or forgotten passwords
Note
To set, change, or delete a password, see “System
security” on page 27.
The server uses complementary metal-oxide
semiconductor (CMOS) memory on the system board for
storing configuration and setup information. CMOS
memory maintains information about:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Date and time
Security features
Power-management devices
Storage devices
Keyboard and mouse
ISA legacy configuration information
Plug and Play configuration information
Port assignments
I/O addresses and interrupts
Other selectable features
Within the security features are the settings for the
power-on and administrator passwords. If you need to
erase a lost or forgotten administrator password, you must
erase all configuration and setup information by moving the
jumper designated for CMOS memory. This jumper is
known as the Clear CMOS Request jumper.
Attention Administrator Password Users:
1. If enhanced security is enabled, and you forget or
lose the administrator password, you must
replace the system board in the server to regain
access to the Configuration/Setup Utility program.
For more information, see “Using the enhanced
security features” on page 32.
2. Clearing CMOS memory erases the configuration
of the server. Therefore, you must reconfigure
the server after clearing CMOS memory. If
possible, record the server configuration
information before moving the Clear CMOS
Request jumper.
The jumper is located on the system board with the label
Clear CMOS Request. To locate this jumper, see “System
board illustration” on page 142, or refer to the label inside
the server.
42
Netfinity Server HMM
Notes
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Using the Configuration/Setup Utility program,
record all configuration information.
Read “Safety information” on page 210.
Power-off the server, but do not disconnect the
cables.
Remove the server cover.
Place the server on its side.
1. Locate the Clear CMOS Request jumper (J9) on the
system board (see “System board illustration” on
page 142).
You might have to remove adapters to gain access to
the jumper. See “Installing or removing ISA and PCI
adapters” on page 62.
2. Move the jumper from its normal position (pins 1 and
2) to pins 2 and 3. It might be helpful to use
needlenose pliers to move the jumper, but be careful
not to scrape any system board components or to
crush the jumper.
3
2
1
3
2
1
3
2
1
3. Power-on the server back on for approximately 10
seconds.
4. Power-off the server.
5. Power-on the server back on.
6. CMOS memory is now cleared and the passwords
have been erased. After the POST completes,
configuration error messages are displayed.
Note
You might not be able to power-off the power
using the power switch until POST is nearly
complete. Unplug the power cord to power-off
the server.
7. Follow the instructions on the screen to continue.
8. When the Configuration/Setup Utility program starts,
make the necessary changes, save the settings, and
exit setup. You must update the server configuration.
When you see a message that instructs you to move
the jumper to the normal position, Power-off the
server.
IBM Netfinity 3000 - Type 8476
43
9. Disconnect the power cord from the rear of the
chassis.
10. Remove the server cover, and move the jumper back
to its normal position (pins 1 and 2).
3
2
1
3
2
1
3
2
1
11. After clearing CMOS memory, you must reconfigure
the server. After reassembling the server (see
“Completing the installation” on page 77), use the
Configuration/Setup Utility program to reset the date
and time, reset any passwords, and reconfigure the
server. For more information, see
“Configuration/Setup utility program menus” on
page 24.
44
Netfinity Server HMM
Power supply
Note
The Front Fan and Disk Fan A are controlled by the
System Management Controller and the power supply
fan is not.
If the power-on indicator is not on, the power-supply fan is
not running, or the computer will not power-off, do the
following.
Check/Verify
FRU/Action
1. Check the following for
proper installation.
Ÿ Power Cord
Ÿ On/Off Switch
connector
Ÿ On/Off Switch
Power Supply
connector
Ÿ System Board
Power Supply
connectors
Ÿ microprocessor(s)
connection
Reseat
2. Check the power cord
for proper continuity.
Power Cord
3. Check the power-on
switch for continuity.
Power-on Switch
If the above are correct, check the following voltages.
Attention
These voltages must be checked with the power
supply cables connected to the system board or riser
card.
Pin
1
10
11
20
Signal
Function
1
3.3 V
+3.3 V dc
2
3.3 V
+3.3 V dc
3
COM
Ground
4
5V
+5 V dc
5
COM
Ground
6
5V
+5 V dc
7
COM
Ground
8
POK
Power Good
IBM Netfinity 3000 - Type 8476
45
46
Pin
Signal
Function
9
5VSB
Standby Voltage
10
12 V
+12 V dc
11
3.3 V
+3.3 V dc
12
-12 V
-12 V dc
13
COM
Ground
14
PS-ON
DC Remote Enable
15
COM
Ground
16
COM
Ground
17
COM
Ground
18
-5 V
-5 V dc
19
5V
+5 V dc
20
5V
+5 V dc
Netfinity Server HMM
ROM operation mode switch setting
If the power to the server is interrupted while POST/BIOS
is being updated, the server might not restart correctly. If
this happens, perform the following procedure to recover.
Notes
Ÿ
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Power-off the server and all other connected
devices.
Disconnect all external cables attached to the
server; then, remove the server cover.
Create a Flash Utility Diskette, see “Remote
administration” on page 34.
Note
If you have not already done so, go to
http://www.ibm.com/support/ on the World Wide Web
and download the appropriate flash update program.
Review the applicable README files, and use this
information to create a Flash Utility Diskette. Perform
the POST/BIOS (flash) update procedure (see
“Remote administration” on page 34 for additional
information).
1. Locate the configuration switches (also known as
rocker switches) on the system board. For more
information, refer to the label inside the server, or see
“System board illustration” on page 142.
2. To set the ROM operation mode to the appropriate
value, set switch 5 as shown in the following
illustration. It might be helpful to use the end of a
small screwdriver to set the switch.
Attention
The following illustration is for reference only.
Before you change the settings for switch 5, be
sure that you check the orientation of the server
system board to correctly identify the switch
number locations. If you change the settings for
the wrong switches, you might seriously damage
server components or options.
Normal ROM Operation
1 2 3 4 5 6 7 8
ROM Recovery Mode
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
3. Move switch 5 to the ON position.
4. Insert the Flash Utility Diskette (POST/BIOS update)
into drive A.
5. Power-on the server.
IBM Netfinity 3000 - Type 8476
47
6. After the update session completes, Power-off the
server and remove the diskette from drive A.
7. Move switch 5 back to the OFF position.
8. Reinstall the cover and reconnect any cables that you
disconnected.
9. Power-on the server to restart the operating system.
10. After changing configuration switch settings, you must
reconfigure the server. After reassembling the server
(see “Completing the installation” on page 77), use
the Configuration/Setup Utility program to reconfigure
the server. For more information, see
“Configuration/Setup utility program menus” on
page 24.
48
Netfinity Server HMM
SCSISelect utility program
The server comes with a menu-driven configuration utility
program, called SCSISelect, that allows you to view and
change SCSI settings.
You can use the SCSISelect Utility program to:
Ÿ
Ÿ
Ÿ
View and change the default SCSI identification (IDs)
Verify and change configuration conflicts
Perform a low-level format on a SCSI hard disk.
Starting the SCSISelect utility program
: You can access this program when you start the
server. The SCSISelect prompt appears after the IBM
Netfinity 3000 server logo appears. Press Ctrl+A
immediately after the SCSISelect prompt appears:
<<< Press <CTRL><A> for SCSISelect Utility! >>>
Use the Up Arrow (↑) or Down Arrow (↓) key to move the
highlight bar to the various menu choices. Press Esc to
return to the previous menu. Also, you can press the F5
key to switch between color and monochrome modes (if
the monitor permits). To change the settings of the
displayed items, such as Channel A or Channel B, follow
the directions on the screen. Then, press Enter.
SCSISelect utility program choices
: The following choices appear on the SCSISelect Utility
program menu:
Ÿ
Ÿ
Configure/View Host Adapter Settings
SCSI Disk Utilities
Configure/View host adapter settings
: To view or change the SCSI controller settings, select
Configure/View Host Adapter Settings and follow the
directions on the screen.
Note
On this menu, the SCSI controller is referred to as the
Host Adapter.
This menu has the following choices:
Ÿ
Host Adapter SCSI ID
Ÿ
The default SCSI ID of the SCSI controller is 7. Do
not change this value.
SCSI Parity Checking
Ÿ
The default value is Enabled. Do not change this
value.
Host Adapter SCSI Termination
The default value is Automatic. Do not change this
value.
IBM Netfinity 3000 - Type 8476
49
Ÿ
Boot Device Options
Select this choice to configure startable device
parameters. Before you can make updates, you must
know the ID of the device whose parameters you
want to configure.
Ÿ
The default startup (boot) SCSI ID is 0 for an internal
SCSI hard disk drive in Channel A.
SCSI Device Configuration
Select this choice to configure SCSI device
parameters. Before you can make updates, you must
know the ID of the device whose parameters you
want to configure.
Notes
1. For SCSI tape drives, set Send Start Unit
Command to Off for that SCSI ID. This
ensures proper server operation.
2. When the Maximum Sync Transfer Rate is
set to 40.0, this value represents the
transfer rate for UltraSCSI devices. When
this value is set to 20.0, it represents the
transfer rate for Fast SCSI devices.
Ÿ
Advanced Configuration Options
Select this choice to view or change the settings for
advanced configuration options. These options
include enabling support for large hard disk drives
and support for drives with UltraSCSI speed.
To reset the SCSI controller defaults, press F6; then,
follow the instructions on the screen.
SCSI disk utilities
: To see the IDs that are assigned to each SCSI device
or to format a SCSI device, select SCSI Disk Utilities from
the SCSISelect Utility program menu.
To use the utility program, select a drive from the list.
Read the screens carefully before you make a selection.
Note
If the following screen appears, you might have
pressed Ctrl+A before the selected drives were ready.
Restart the server, and watch the SCSISelect
messages as each drive spins up. After the drive that
you want to view or format spins up, press Ctrl+A.
50
Netfinity Server HMM
à
ð
Unexpected SCSI Command Failure
Target SCSI ID:
4
SCSI CDB Sent:
ð3 ðð ðð ðð ðE ðð ð7 ðð ð2 ðð
Host Adapter Status:
ððh - No host adapter error
Target Status:
ð2h - Check condition
Sense Key:
ð2h - Not ready
+Sense Code:
ð4h
+Sense Code Qualifier:
ð2h
Press 'Esc' to continue.
á
ñ
Performing a low-level disk format
: You can use the Format Disk feature of the
SCSISelect Utility program to perform a low-level format on
hard disks.
Depending on the hard disk capacity, the low-level format
program could take up to two hours.
When to use the format disk program
: Use the Format Disk program:
Ÿ
Ÿ
Ÿ
When you are installing software that requires a
low-level format
When you get recurring messages from the diagnostic
tests directing you to run the Low-Level Format
program on the hard disk
As a last resort before replacing a failing hard disk
drive
Note
For information about backing up all of the files, see
the operating-system documentation.
Starting the low-level format
Attention
The low-level format erases all data and programs.
1. If the hard disk drive is working, make a backup copy
of all the files and programs on the hard disk.
2. Select Format Disk; then, follow the instructions on
the screen.
IBM Netfinity 3000 - Type 8476
51
Note
Hard disks normally contain more tracks than
their stated capacity (to allow for defective
tracks). A message appears on the screen if the
defect limit is reached. If this happens, replace
the hard disk.
3. To install an operating system after the hard disk is
formatted, follow the instructions in the ServerGuide
package that comes with the server.
52
Netfinity Server HMM
Specifications (Ethernet cable)
This appendix contains the specifications for the
unshielded twisted-pair (UTP) cables that can be used to
connect the server to an IEEE Standard 802.3 network.
The Ethernet controller on the system board provides
10BASE-T and 100BASE-TX support through the RJ-45
connector on the back of the server. When you connect
the server to the network, the Ethernet controller
automatically detects the data-transfer rate (10 Mbps or
100 Mbps) on the network and then sets the controller to
operate at the appropriate rate.
The following information describes the specifications for
the unshielded twisted-pair (UTP) cable that can be used
to connect the server to an IEEE Standard 802.3 network.
Attention:
To connect the server's 10BASE-T or 100BASE-TX port to
a repeater, use an UTP EIA/TIA-568 Category 5 cable that
is terminated with RJ-45 connectors. This is a requirement
to meet various governmental standards, including
electromagnetic compatibility.
The cables used in 10BASE-T or 100BASE-TX link
segments do not require grounding. However, all devices
connected to the cables must be grounded.
Connect the appropriate type of UTP cable to the repeater.
Ÿ
Ÿ
If the port on the repeater is a crossover port (also
called an MDI-X port), use a UTP cable that is wired
as a straight-through cable.
If the port on the repeater is not a crossover port
(also known as an MDI port), use a UTP cable that is
wired as a crossover cable.
The server contains three diagnostic light-emitting diodes
(LEDs) for the Ethernet connector, one located on the front
and two located on the rear of the server.
Ÿ
Ÿ
When the green LED is on, it indicates that the
Ethernet controller is connected to a hub or switch
and is receiving link pulses. This LED is also known
as the Link OK light.
When the amber LED is on, it indicates that the
Ethernet network is operating at 100 Mbps. When
this LED is off, it indicates that the Ethernet network
is operating at 10 Mbps.
Do not use telephone extension cables to connect the
server to a repeater. The wire pairs in those cables are
not twisted, and the cables do not meet other requirements
for use in a 10BASE-T or 100BASE-TX network. You can
identify telephone extension cables by their flat and thin
appearance. UTP cables are rounder and thicker than
telephone extension cables.
IBM Netfinity 3000 - Type 8476
53
Table 1 on page 54 describes the specifications for UTP
cables used in 10BASE-T and 100BASE-TX link segments.
Cables for these link segments must be certified as
EIA/TIA-568 Category 5.
Table 1. Cabling Specifications for 10BASE-T and
100BASE-TX Link Segments
Characteristic
Specificationñ
Cable type
UTP cable with two twisted pairs
of 22, 24, or 26 AWGò wire
Nominal impedance
100 Ohms
Velocity of propagation
0.585 có
Maximum attenuation
Ÿ
Ÿ
For 10BASE-T: 8 to 10 dB
per 100 m at 10 MHz
For 100BASE-TX: 67 dB
per 305 m at 100 MHz
Notes:
1. Cables that have been certified as EIA/TIA-568 Category 5 meet all
10BASE-T and 100BASE-TX specifications. An EIA/TIA-568
Category 5 cable must be used for 10BASE-T and 100BASE-TX.
2. The cable can contain two to four twisted pairs, but only two of the
pairs will be used by the 10BASE-T or 100BASE-TX network.
3. The c represents the velocity of light traveling in a vacuum, which
is 300 000 km/sec (186 400 mi/sec).
Note
AWG = American Wire Gauge
EIA = Electronics Industries Association
STP = shielded twisted pair
TIA = Telecommunications Industries Association
The following figure illustrates the RJ-45 connector.
10BASE-T or 100 BASE-TX
UTP Cable
1
2
RJ-45 Modular Plug Connector
3
Pins
6
The following figure illustrates the wiring in straight-through
cables.
RJ-45 Modular Connector
10BASE-T / 100 BASE-TX RJ-45 Modular Connector
Signal
Name
Pin
Pin
Signal
Name
1
TD+
1
1
TD+
1
TD
2
2
TD
2
RD+
3
3
RD+
2
RD
6
6
RD
Twisted
Pair
3, 4
(Not used) 4, 5, 7, 8
Relative to the device connected to the adapter
54
Netfinity Server HMM
4, 5, 7, 8
(Not used)
The following figure illustrates the wiring in crossover
cables.
RJ-45 Modular Connector 10BASE-T / 100BASE-TX RJ-45 Modular Connector
Twisted
Pair
Signal
Name
Pin
Pin
Signal
Name
1
TD+
1
1
TD+
1
TD
2
2
TD
2
RD+
3
3
RD+
2
RD
6
6
RD
3, 4
(Not used) 4, 5, 7, 8
4, 5, 7, 8
(Not used)
Relative to the device connected to the adapter
Note
For additional information about Ethernet protocols,
refer to the Ethernet documentation.
Wake on LAN feature
: The Wake on LAN feature is built into the Ethernet
controller. To enable this feature, you must install the
appropriate software in the server. See the Ethernet
documentation for additional information about Wake on
LAN operation.
To use the Wake on LAN feature with an Ethernet adapter,
you must install Wake on LAN cables. For instructions,
refer to the documentation and cables that come with the
adapter.
IBM Netfinity 3000 - Type 8476
55
Specifications (system)
The following table contains the environmental
specifications for the Netfinity 3000 server.
Notes
1. The following levels were measured in controlled
acoustical environments according to procedures
specified by the American National Standards
Institute (ANSI) S12.10 and ISO 7779, and are
reported in accordance with ISO 9296.
2. Actual sound-pressure levels in your location
might exceed the average values stated because
of room reflections and other nearby noise
sources. The declared sound power levels
indicate an upper limit, below which a large
number of computers will operate.
Size
Depth: 445 mm (17.5 in.)
Width: 200 mm (7.9 in.)
Height: 492 mm (19.4 in.)
Ÿ
Ÿ
Ÿ
Weight
Maximum configuration (as shipped): 17.3 kg (38 lb)
Standard configuration (as shipped): 15 kg (33 lb)
Ÿ
Ÿ
Environment
Air temperature:
– System on: 10° to 35°C (50° to 95°F) at altitude 0–915 m (3000 ft)
10° to 32°C (50° to 90°F) at altitude 915–2134 m
(3000–7000 ft)
– System off: 10° to 43°C (50° to 110°F)
Humidity:
– System on: 8% to 80%
– System off: 8% to 80%
Ÿ
Ÿ
Heat Output
Approximate heat output in British thermal units (Btu) per hour:
– Maximum configuration (as shipped): 306 Btu/hour (90 watts)
– Maximum configuration (theoretical)1: 1564 Btu/hour (460 watts)
Ÿ
Electrical Input
Sine-wave input (50/60 Hz) is required
Input voltage:
– Low range:
- Minimum: 90 V ac
- Maximum: 137 V ac
– High range:
- Minimum: 180 V ac
- Maximum: 265 V ac
– Input kilovolt-amperes (kVA) (approximately):
- Maximum (configuration as shipped): 0.70 kVA
Ÿ
Ÿ
Power consumption and heat output vary depending on the number and type
of optional features installed and the power-management optional features in
use.
Acoustical Noise-Emission Values
Average sound-pressure levels:
– At operator position:
- 35 dBA idle
- 40 dBA operating
Ÿ
1
Under typical maximum configurations, the heat output will be
substantially below the theoretical maximum.
56
Netfinity Server HMM
–
Ÿ
At bystander position –1 meter (3.3 ft):
- 33 dBA idle
- 36 dBA operating
Declared (upper limit) sound power levels:
– 4.7 bels idle
– 5.0 bels operating
IBM Netfinity 3000 - Type 8476
57
Locations
The following information supports the Netfinity 3000 Type 8476 server.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
58
“Bottom cover” on page 71.
“Cabling” on page 73.
“CD-ROM drive” on page 74.
“Completing the installation” on page 77.
“Controls and indicators” on page 81.
“Disconnecting cables and removing the side cover”
on page 84.
“External options” on page 87.
“External SCSI devices” on page 88.
“External view” on page 91.
“Front fan” on page 92.
“Input/Output connectors” on page 94.
“Internal drives” on page 97.
“Internal view” on page 125.
“Memory modules” on page 126.
“Microprocessors” on page 130.
“Preliminary option installation information” on
page 136.
“Stabilizing feet” on page 138.
“System board” on page 139.
“System board illustration” on page 142.
“System board replacement” on page 144.
“Switch settings” on page 145.
“Updating the server configuration” on page 150.
“Video port connector” on page 152.
Netfinity Server HMM
Accessing the system board
Before you can install or remove certain options, you might
need to access the system board. For example, you might
need to remove adapters, drives, and cables that impede
your access to components on the system board. You
also need to access the system board before you can
install or remove such options as adapters, memory
modules, and microprocessors, because these devices
reside on the system board.
To access the system board more easily:
1. Rotate the stabilizer feet in towards the server, so
that they do not detach due to the weight of the
server.
2. Place the server on a flat, sturdy surface, such as a
table.
3. Turn the server on its side, so that the system board
is facing you.
If you access the inside of the server while it is in the
upright position, ensure that the stabilizer feet are
positioned correctly. For more information, see “Stabilizing
feet” on page 138.
Note
To see a list of the system board components and an
illustration that shows their locations, see “System
board illustration” on page 142.
IBM Netfinity 3000 - Type 8476
59
Adapters
Adding an adapter, such as a communication adapter,
extends the capabilities and power of the server. For
example, if the server supports redundant array of
independent disks (RAID) technology, you can add a RAID
adapter that can enhance logical-drive capacity and
performance.
Note
For a complete list of the adapters that the server
supports, go to http://www.ibm.com/pc/us/compat/ on
the World Wide Web, or contact an IBM marketing
representative.
When you are installing or removing adapters, it is
important to resolve any resource conflicts that might arise.
For example, if you install an ISA legacy adapter, you
might need to manually configure the adapter by setting a
variety of switches on the adapter and by using the
Configuration/Setup Utility program.
Many adapters now use Plug and Play technology, which
enables the server to automatically configure the adapter,
provided that the required resources are available. Refer
to the instructions that come with the adapter to determine
if it is Plug and Play. For more information, see “ISA
legacy resources” on page 36.
Adapter considerations: The server has
connectors for Accelerated Graphics Port (AGP), industry
standard architecture (ISA), and peripheral component
interconnect (PCI) adapters. The following sections
contain additional information about these types of
adapters.
AGP adapters: You may install a video adapter in the
dedicated AGP slot connector, in an ISA slot connector, or
in a PCI slot connector. However, the server system
board supports either the integrated video subsystem or
the AGP video connector, but not both simultaneously.
The server contains one dedicated AGP slot connector on
the inside rear of the server wall, adjacent to the
dual-inline memory module (DIMM) connectors. To locate
the dedicated AGP slot connector, see “System board
illustration” on page 142.
If you need to install an AGP adapter in the dedicated
AGP slot connector, go to “Installing or removing AGP
adapters” on page 65. If you need to install a video
adapter in an ISA or PCI slot connector, go to “ISA and
PCI adapters” on page 61.
60
Netfinity Server HMM
ISA and PCI adapters: The server uses a riser card
for expansion. The riser card contains expansion slot
connectors that connect adapters to the industry standard
architecture (ISA) and peripheral component interconnect
(PCI) buses.
You can install a variety of adapters in the expansion slot
connectors on the riser card. For information on locating
the riser card, see “System board illustration” on
page 142. For an illustration of the expansion slots that
are located on the rear of the server, see “Input/Output
connectors” on page 94.
The riser card in the server has three dedicated ISA slot
connectors and three dedicated PCI slot connectors.
The following illustration shows the expansion slot
connectors and other connectors on the riser card.
ISA
Disk Fan A
Connector
Disk Fan B
Connector
ISA
ISA
Front Fan Connector
PCI
SCSI Hard Disk LED
Connector
Wake on LAN Connector
Asset ID Antenna
Connector
PCI
PCI
Chassis-Intrusion
Detector Connector
Internal Speaker
Connector
CD
Audio
Connector
340-Pin
Connector
Alert on LAN
Connector
Modem Wakeup
Connector
Notes
1. Alert on LAN and Asset ID are available on
some models only.
2. If you attach a 4-position cable connector to the
2-pin Modem Wakeup connector, ensure that the
unused positions are next to the bottom of the
riser card, as shown in the illustration. If this
cable is incorrectly attached, the server might
automatically restart each time that you Power-off
the power.
IBM Netfinity 3000 - Type 8476
61
ISA
Disk Fan A
Connector
Disk Fan B
Connector
ISA
ISA
Front Fan Connector
PCI
SCSI Hard Disk LED
Connector
Wake on LAN Connector
Asset ID Antenna
Connector
Chassis-Intrusion
Detector Connector
PCI
PCI
Internal Speaker
Connector
CD
Audio
Connector
340-Pin
Connector
Alert on LAN
Connector
Modem Wakeup Connector
Attention
To avoid possible damage to adapters and server
components, be sure that the adapters that you install
do not touch each other or the other components
(such as the microprocessor) inside the server.
Installing or removing ISA and PCI
adapters: This section gives the procedure for
installing an ISA or PCI adapter. If you want to remove an
ISA or PCI adapter, reverse the order of the following
steps. If you need to install an AGP adapter in the
dedicated AGP slot connector, go to “Installing or removing
AGP adapters” on page 65.
Notes
1. See “Input/Output connectors” on page 94 for an
illustration of the expansion slots on the rear of
the server.
2. If you install an ISA legacy adapter, set the
resources to [ISA Resource]; this reserves the
resources for the legacy adapter and prevents
the BIOS from using these resources for the
system or other adapters. If you remove an
adapter, reassign the system resources as
[Available] for ISA legacy adapters. See “ISA
legacy resources” on page 36.
3. To install some adapters, especially full-length
adapters, you might need to remove the bottom
cover, system board, microprocessor, and front
fan.
Notes
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Read the documentation that comes with the
option.
Read “Accessing the system board” on page 59.
To install an ISA or PCI adapter:
62
Netfinity Server HMM
1. Review the instructions that come with the adapter to
determine if it must be installed in an ISA or PCI
expansion slot; otherwise, use any empty,
bus-compatible slot.
2. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
3. If necessary, remove the bottom cover (see “Bottom
cover” on page 71).
4. Remove the screw and bracket.
5. Remove the appropriate expansion-slot cover:
a. Remove the expansion-slot screw on the top of
the expansion-slot cover.
b. Slide the expansion-slot cover out of the server.
c. Store the expansion-slot cover in a safe place for
future use.
6. Touch the static-protective package that contains the
adapter to any unpainted metal surface on the server;
then, remove the adapter from the package.
7. Install the adapter into the appropriate slot on the
riser card.
You might have to remove the system board and the
front fan in order to slide the adapter into the slot.
See “Front fan” on page 92 and “System board” on
page 139.
Note
The components of a PCI adapter face down
toward the system board, and the components of
an ISA adapter face up. If a component in the
server or on the adapter interferes with the
installation, use another slot.
IBM Netfinity 3000 - Type 8476
63
Expansion-Slot
Cover
Adapter
Card
Riser Card
8. Install the bracket and the screw.
9. If you installed a network adapter that uses Wake on
LAN or Alert on LAN, attach the cable from the riser
card to the adapter. See “ISA and PCI adapters” on
page 61 to locate the Wake on LAN or Alert on LAN
connector. If you installed a modem and want to use
Modem Wakeup, see “ISA and PCI adapters” on
page 61 to locate the Modem Wakeup connector on
the riser card.
10. If you removed the bottom cover, the front fan, or the
system board, replace them. See “Front fan” on
page 92, “System board” on page 139, and “Bottom
cover” on page 71.
11. If necessary, connect any internal cables to the
adapter. Refer to the documentation that comes with
the option.
12. If you installed an ISA legacy adapter, go to “ISA
legacy resources” on page 36 to assign system
resources.
13. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
64
Netfinity Server HMM
Installing or removing AGP adapters:
This
section gives the procedure for installing an AGP adapter
in the dedicated AGP slot connector. If you want to
remove an AGP adapter from this slot connector, reverse
the order of the following steps. If you need to install an
adapter in an ISA or PCI slot connector, go to “Installing or
removing ISA and PCI adapters” on page 62.
Notes
1. You may install a video adapter in the dedicated
AGP slot connector, in an ISA slot connector, or
in a PCI slot connector. However, the server
system board supports either the integrated video
subsystem or the AGP video connector, but not
both simultaneously.
2. You can install only a special AGP graphics
adapter in the dedicated AGP slot connector.
For information on the available AGP adapters,
go to http://www.ibm.com/pc/us/compat/ on the
World Wide Web.
Note
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Read the documentation that comes with the
option.
Read “Accessing the system board” on page 59.
Attention
The presence of 5 V ac standby power might result in
damage to the hardware unless you disconnect the
power cord from the electrical outlet before you open
the server.
To install an AGP adapter:
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Remove the screw; then, remove the cover to access
the two slots on the server wall. The slots on the
server wall provide access to the connector on the
AGP adapter for attaching external devices.
IBM Netfinity 3000 - Type 8476
65
3. Install the AGP adapter. The following illustration
shows the installation of an AGP adapter. Note that
the connector for external devices on the AGP
adapter is accessible through the slot on the server
wall.
Note
Some adapters support the attachment of
secondary adapters called daughterboards. (A
daughterboard is an adapter that can be plugged
into another adapter or the system board.)
Because a daughterboard might provide another
connector for external devices, a second slot is
provided in the server wall for access.
4. If necessary, connect any internal cables to the
adapter. Refer to the documentation that comes with
the option.
5. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
66
Netfinity Server HMM
Adding security options
Security features can help to protect the server data and
programs from unauthorized access and use, and help to
physically protect the server from theft and tampering.
After you determine the system security needs, you can
activate or implement the appropriate security features.
To control access to the information in the server
databases, you can implement security measures through
the system configuration programs. These features
include defining two levels of password protection,
restricting diskette access, and defining a system owner's
name. Implementing these security measures helps you to
ensure the integrity of the data and programs that are
stored in the server. See “System security” on page 27
for details.
To prevent writing to a diskette in a diskette drive, set the
diskette write-protect switch, as described in “Diskette
write-protect switch setting” on page 147.
To erase lost or forgotten passwords, you can move the
CMOS clear (password) jumper on the system board.
To control access to other hardware components in the
server, you can install several types of optional devices.
These options include:
U-bolt
Security cable
Padlock
Ÿ
Ÿ
Ÿ
The following section discusses these security options.
Installing a U-bolt and security cable:
You
can help to deter unauthorized removal of the Netfinity
3000 server by installing a U-bolt and security cable on the
rear of the server. After you add the security cable, make
sure that it does not interfere with other cables that are
connected to the server.
Note
Ÿ
Ÿ
Obtain the following:
– A 19 mm (3/4 in.) U-bolt or wire rope
(similar to National Manufacturing No. 3230,
Stock No. 176-735)
– Threaded nuts that fit the U-bolt
– A security cable
– A lock, such as a combination lock or
padlock
Read “Safety information” on page 210.
IBM Netfinity 3000 - Type 8476
67
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Locate the two holes on the lower right edge of the
rear of the server.
3. Insert the U-bolt through the rear panel; then, attach
and tighten the nuts with an appropriately sized or
adjustable wrench.
4. If you have completed installing the U-bolt and do not
want to install any other internal options, replace the
server side cover and reconnect all external cables
and power cords. (See “Completing the installation”
on page 77 if you need additional information.)
5. Thread the cable through the U-bolt and around an
object that is not a part of or permanently secured to
the building structure or foundation, and from which it
cannot be removed; then, fasten the cable ends
together with a lock.
The following illustration shows an example of how
this might work.
Cable
Padlock
68
Netfinity Server HMM
Battery
If the server battery malfunctions, you must replace it as
described in this section.
IBM has designed this product with your safety in mind.
The lithium battery must be handled correctly to avoid
possible danger. If you replace the battery, you must
adhere to the following instructions.
Caution
When replacing the battery, use only IBM Part
Number 33F8354 or an equivalent type battery
recommended by the manufacturer. If the system has
a module containing a lithium battery, replace it only
with the same module type made by the same
manufacturer. The battery contains lithium and can
explode if not properly used, handled, or disposed of.
Do not:
Ÿ
Ÿ
Ÿ
Throw or immerse into water
Heat to more than 100°C (212°F)
Repair or disassemble
Dispose of the battery as required by local ordinances
or regulations.
Note
In the U.S., please call 1-800-IBM-4333 for information
about battery disposal.
To order replacement batteries, call 1-800-772-2227 within
the United States, and 1-800-465-7999 or 1-800-465-6666
within Canada. Outside the U.S. and Canada, call your
IBM reseller or IBM marketing representative.
Notes
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Followed any special handling and installation
instructions supplied with the replacement
battery.
Removed the server side cover.
Note
After you replace the battery, you must reconfigure the
system and reset the system date and time.
To replace the battery:
1. Locate the battery on the system board (see “System
board illustration” on page 142).
IBM Netfinity 3000 - Type 8476
69
2. Remove the battery:
a. Use one finger to lift the battery clip over the
battery.
b. Use one finger to slightly slide the battery toward
the front of the server. The spring mechanism
behind the battery will push it out toward you as
you slide it forward.
c. Use your thumb and index finger to pull the
battery from under the battery clip.
d. Ensure that the battery clip is touching the base
of the battery socket by pressing gently on the
clip.
3. Insert the new battery:
a. Tilt the battery so that you can insert it into the
front of the socket, under the battery clip.
b. As you slide it under the battery clip, press the
battery down into the socket.
4. Reinstall the server covers and complete the
installation (see “Completing the installation” on
page 77).
Note
When you turn on the server for the first time
after you replace the battery, an error message
might appear. This is normal after battery
replacement.
5. Start the Configuration/Setup Utility program and
reset configuration parameters as needed.
Ÿ To reset the system date and time, go to “Date
and time” on page 26.
Ÿ To reset the power-on password, go to “Setting
power-on password modes” on page 27.
Ÿ To reconfigure the system, follow the instructions
given in “Configuration/Setup utility program” on
page 21 (all models).
70
Netfinity Server HMM
Bottom cover
Attention
The presence of 5 V ac standby power might result in
damage to the hardware unless you disconnect the
power cord from the wall before you open the server.
Note
Ÿ
Ÿ
Read “Safety information” on page 210.
Read the documentation that comes with the
option.
To remove the bottom cover:
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Position the server as described in “Accessing the
system board” on page 59.
3. Remove the screws from the bottom cover.
4. Pivot the end of the bottom cover away from the
server frame.
Note
The server bottom cover might look different from
the bottom cover in this illustration.
5. Slide the tabs on the end of the cover out of their
openings and remove the cover.
To replace the bottom cover:
1. Hold the bottom cover at an angle and align the tabs
on the end with the openings in the frame.
2. Fit the tabs into the openings and pivot the bottom
cover until it is closed.
IBM Netfinity 3000 - Type 8476
71
3. Align the holes and insert the two bottom screws.
4. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
72
Netfinity Server HMM
Cabling
Before cabling the server:
Ÿ
Ÿ
Make sure that you have an adequate number of
properly grounded electrical outlets for the server,
monitor, and any other options that you intend to
install.
Place the server in a location that is dry. Rain or
spilled liquids might damage the server.
Note
To allow for air circulation, be sure to maintain the
clearances.
To cable the server:
1. Use the following illustration to cable the server.
For information about Ethernet cables, see
“Specifications (Ethernet cable)” on page 53.
Power Connector
Expansion Slots
External SCSI Device
Microphone
Audio
Line In
Audio
Line Out
USB 1
ISA 3
ISA 1
ISA 2
USB 2
2
1
Serial 1
Serial 2
2
1
Keyboard
PCI 3
Parallel
PCI 2
PCI 1
Ethernet
(RJ-45)
Mouse
Monitor
2. Connect all power cords to electrical outlets.
IBM Netfinity 3000 - Type 8476
73
CD-ROM drive
An IDE CD-ROM drive is a standard feature on all Netfinity
3000 servers. CD-ROM drives can play back or read from
a CD, but cannot write information to it. CD-ROM drives
use industry-standard, 12 cm (4.75-inch) CDs.
Follow these guidelines when using a CD-ROM drive:
Ÿ
Ÿ
Ÿ
Do not place the server where the following
conditions exist:
– High temperature
– High humidity
– Excessive dust
– Excessive vibration or sudden shock
– An inclined surface
– Direct sunlight
Do not insert any object other than a CD into the
drive.
Before moving the server, remove any CD from the
drive.
The following is an illustration of the front bezel of the
server, with the CD-ROM drive location, controls, and
indicators.
Tray
Eject/Load Button
Emergency-Eject Hole
CD-ROM Drive
In-Use Light
7 tekcoS
74
Netfinity Server HMM
The following illustration shows the front of the CD-ROM
drive.
CD-ROM Drive
In-Use Light
Handling a CD:
Emergency-Eject
Hole
Eject/Load
Button
When handling a CD, follow these
guidelines:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Hold the CD by its edges. Do not touch the surface.
To remove dust or fingerprints, wipe the CD from the
center to the outside. Wiping the CD in a circular
direction might cause loss of data.
Do not write or stick paper on the CD.
Do not scratch or mark the CD.
Do not place or store the CD in direct sunlight.
Do not use benzene, thinners, or other cleaners to
clean the CD.
Do not drop or bend the CD.
Loading and unloading a CD
Note
Before you load or unload a CD, be sure that you
have turned on the server.
To load and unload a CD in a CD-ROM drive:
1. Press the Eject/Load button. The tray slides out of
the drive. (Do not manually force the tray open.)
2. Place the CD in the tray with the label facing up.
3. Close the tray by pressing the Eject/Load button, or
by gently pushing the tray forward. When the tray is
closed, the CD-ROM drive in-use light on the front of
the drive will activate to indicate that the drive is in
use.
4. To eject the CD, press the Eject/Load button. When
the tray slides out, carefully remove the CD.
5. Close the tray by pressing the Eject/Load button, or
by gently pushing the tray forward.
IBM Netfinity 3000 - Type 8476
75
Notes
1. If the tray does not slide out of the drive when
you press the Eject/Load button, insert one end
of a large paper clip into the emergency-eject
hole located above and to the left of the
CD-ROM drive in-use light.
2. In some models, you might have to remove the
front bezel from the CD-ROM drive to access the
emergency-eject hole.
76
Netfinity Server HMM
Completing the installation
Notes
Ÿ
Ÿ
Complete all the installation procedures for the
internal options that you have chosen to install.
Read “Safety information” on page 210.
1. Ensure that all components have been reassembled
correctly and that no tools or loose screws are left
inside the server.
2. Clear any cables that might impede the replacement
of the cover.
3. Place the server in an upright position, and ensure
that the stabilizer feet are positioned correctly. For
more information, see “Stabilizing feet” on page 138.
Note
It is easier to install the cover if the server is
placed in an upright position.
4. Install the side cover:
a. Make sure that the cover lock (if present) is in
the unlocked position.
Cover
Lock
IBM Netfinity 3000 - Type 8476
77
b. Align the three bottom cover guides with the
corresponding notches on the frame of the
server.
Tab
Opening
Notches
c. Insert the bottom cover tab into the tab opening.
Tab
Notches
d. With one hand, align the top so that the cover
rests against the server. With the other hand,
press the cover at the bottom left corner, above
the left rotated foot.
78
Netfinity Server HMM
7 tekcoS
e. Keep the hand at the top to hold the cover in
place. Use the thumb from the other hand to
slide the cover forward, as shown in the
following illustration. Make sure that the cover is
latched into position.
7 tekcoS
5. If a cover lock is present, go to the back of the server
and lock the cover.
You can use the cover lock and keys to secure the
outside cover.
IBM Netfinity 3000 - Type 8476
79
Attention
In the United Kingdom, by law, the telephone
cable must be connected after the power cord.
Caution
When the power-cord strain-relief bracket option
is installed on the power cord, the server must be
plugged to a power source that is easily
accessible.
6. Reconnect the cables to the back of the server; then,
plug the power cords into properly grounded electrical
outlets.
Keyboard
Mouse
Monitor
Parallel
Device
Serial
Device
USB
Device
Ethernet
Device
Audio
Devices
SCSI
Device
7. If you have a modem or fax machine attached to the
server, and you are not in the United Kingdom,
reconnect the telephone line to the wall outlet and the
server, and plug the power cords into properly
grounded electrical outlets.
If you are in the United Kingdom, plug in the power
cords first; then, connect the telephone line to the wall
outlet and the server.
8. Power-on the server and all attached devices.
Attention
To allow for air circulation, be sure to maintain the
following minimum clearances around the server:
Ÿ
Ÿ
Ÿ
102 mm (4 in.) in the front
127 mm (5 in.) in the rear
51 mm (2 in.) on the left and right sides
When you have completed installing the covers and
cables, go to “Updating the server configuration” on
page 150.
80
Netfinity Server HMM
Controls and indicators
The most commonly used controls and status indicators
are on the front of the server.
Server controls
Power Switch
CD-ROM
Eject/Load Button
Diskette
Eject Button
7 tekcoS
Power Switch: Press this switch to turn
the server on or off.
Attention
Do not turn off the server if a drive
in-use light is on. This might damage
the information stored on a hard disk
or on a diskette.
When the power is on, there is a period
of time during the power-on self-test
(POST), a short test that occurs when the
server is turned on, when a single touch
of the power switch will not turn off the
power. If power must be turned off during
POST, press and hold the power switch
for 5 seconds or disconnect the power
cord. After POST, the power switch
works normally, unless the server is in a
hang condition. If the server is in a hang
condition, press and hold the power
switch until the power turns off.
CD-ROM Eject/Load Button: Push this
button to release a CD from the CD-ROM
drive. See “CD-ROM drive” on page 74
for additional information about the
CD-ROM drive controls and indicators.
Diskette Eject Button: Push this button
to release a diskette from the diskette
drive.
IBM Netfinity 3000 - Type 8476
81
Status indicators:
The following illustration
identifies the indicators located on the front of the server.
Power-On Light
Hard-Disk Drive
In-Use Light
Ethernet Activity Light
CD-ROM Drive
In-Use Light
7 tekcoS
Diskette Drive
In-Use Light
Power-On Light: This light comes on
when you turn on the server by pressing
the power switch.
Hard Disk Drive In-Use Light: This light
comes on when the server is accessing a
SCSI hard disk drive. If this light remains
illuminated, it might indicate that either
the SCSI bus or the system
microprocessor has stopped.
Ethernet Activity Light: This light
comes on when the Ethernet controller is
transmitting data to or receiving data from
another system in the network.
Ethernet Diagnostic LED:
The server contains diagnostic
light-emitting diodes (LEDs) for the
Ethernet connector located on the rear
panel of the server.
Ÿ
Ÿ
When the green LED is on, it
indicates that the Ethernet controller
is connected to a hub or switch and
is receiving link pulses. This LED is
also known as the Link OK light.
When the amber LED is on, it
indicates that the Ethernet network is
operating at 100 Mbps. When this
LED is off, it indicates that the
Ethernet network is operating at 10
Mbps.
CD-ROM Drive In-Use Light: This light
comes on when the CD-ROM drive is
accessed.
82
Netfinity Server HMM
Diskette Drive In-Use Light: This light
comes on when the diskette drive is
accessed.
IBM Netfinity 3000 - Type 8476
83
Disconnecting cables and removing the
side cover
Attention
The presence of 5 V ac standby power might result in
damage to the hardware unless you disconnect the
power cord from the electrical outlet before you open
the server.
1. Remove any media (diskettes or CDs) from the
drives; then, power-off all attached devices and the
server.
Caution
The Power Control button on the front of the
server does not turn off the electrical current
supplied to the server. The server also might
have more than one power cord. To remove all
electrical current from the server, ensure that all
power cords are disconnected from the power
source.
2. Touch the rear of the bare metal frame to dissipate
any static electricity from your body.
3. Before disconnecting cables, be sure to note where
they attach, so that you can correctly reattach them
later.
Note
If you are in the United Kingdom, you must
perform step 5 before step 4.
4. Unplug all power cords (cables) from electrical
outlets.
5. If you have a modem or fax machine attached to the
server, disconnect the telephone line from the wall
outlet and the server.
6. Note the location of the remaining cables and cords.
84
Netfinity Server HMM
Caution.
Electrical current from power, telephone, and
communication cables can be hazardous. To
avoid personal injury or equipment damage,
disconnect the attached power cords,
telecommunications systems, networks, and
modems before you open the server covers,
unless instructed otherwise in the installation and
configuration procedures.
7. Disconnect all cables attached to the server; this
includes power cords, input/output (I/O) cables, and
any other cables that are connected to the server.
Notes
1. For more information about the rear
connectors, see “Input/Output connectors”
on page 94.
2. For more information about ports, including
universal serial bus (USB), see “External
options” on page 87.
Keyboard
Mouse
Monitor
Parallel
Device
Serial
Device
USB
Device
Ethernet
Device
Audio
Devices
SCSI
Device
IBM Netfinity 3000 - Type 8476
85
8. If necessary, unlock the server side cover. (The
cover lock is located at the rear of the server.)
Cover
Lock
9. Remove the side cover by pulling out on the
cover-release tab at the rear of the side cover. Then,
slide the cover toward the front of the server and lift it
off.
10. Set the door aside.
CoverRelease
Tab
86
Netfinity Server HMM
External options
Some examples of the external options that you can
connect to the server include SCSI drives and storage
enclosures, printers, modems, and other serial and parallel
devices.
To attach an external option:
1. Power-off the server and all attached devices.
2. Follow the instructions that come with the option and
the information in this section to connect it to the
server.
The information in this section supplements the instructions
that come with the external option. Use the instructions
that come with the option to prepare it for installation.
Adding a hot-swap storage expansion
enclosure: You can connect a storage enclosure to
the external SCSI connector on the separately installed
SCSI adapter. Contact your IBM reseller or IBM marketing
representative for additional information.
Hot-Swap Drive Bays
IBM Netfinity 3000 - Type 8476
87
External SCSI devices
Note
If an internal device(s) is/are attached to the SCSI
controller, only one external device is supported.
The internal SCSI connector provides support for SCSI
devices installed inside the server. The external SCSI
connector provides support for external SCSI devices. The
UltraSCSI adapter can support a maximum of 15 devices.
Notes
Ÿ
Ÿ
Ÿ
If you plan to install both internal and external
SCSI devices, you must follow the instructions
given in “Internal drives” on page 97 in addition
to the instructions in this section. Read “Internal
drives”; then, return here.
For additional information about SCSI
configurations supported, see
http://www.ibm.com/pc/us/netfinity/
The server comes with a wide (16-bit) SCSI
cable that supports 16-bit devices. If you want to
attach narrow (8-bit) devices to the server, you
must purchase a SCSI 68-pin to 50-Pin
Converter that will enable the connection of the
device to the cable that comes with the server.
It is good practice not to exceed the following
cable-length guidelines:
– If you connect one or more UltraSCSI
devices to the UltraSCSI adapter, do not
exceed 1.5 meters (5 feet) total length for all
cables (internal and external).
– If you connect only Fast SCSI devices to the
UltraSCSI adapter, do not exceed 3 meters
(10 feet) total length for all cables (internal
and external).
Attention
In addition to cable length and the number of installed
devices, you must consider other factors that limit the
performance of the SCSI subsystem. For example, if
you install UltraSCSI devices in an external expansion
enclosure that is limited to Fast transfer rates, or if you
exceed the previously described cable-length
guidelines, the transfer rate to all SCSI devices must
be limited to Fast or standard transfer rates. You
accomplish this by using the SCSISelect Utility
program. See “SCSISelect utility program” on
page 49 for additional information.
If you plan to attach an external SCSI device, you must
order an additional SCSI cable. That is, to use an external
88
Netfinity Server HMM
device with the Netfinity 3000 server, you must connect it
to the external SCSI connector, using a SCSI cable. This
SCSI cable must have the proper connector for the SCSI
external connector on one end, and the proper connector
for the external device on the other end. To select and
order the correct SCSI cable for use with the external
device, contact your IBM reseller or IBM marketing
representative.
Serial port connectors: Serial ports are used to
communicate with printers, plotters, external modems,
auxiliary terminals, and other computers. The server
provides two serial ports (1 and 2). You can add more
serial ports by installing a serial adapter in one of the
expansion slots.
Serial ports transfer data asynchronously; they can
transmit any number of bits at any time, with no restriction
on the duration of the pauses between characters.
The serial ports transmit and receive data and commands
at a rate of 300 bits per second (bps) up to 115 200 bps.
The bits-per-second measurement is commonly referred to
as the baud rate.
Both of the serial connectors on the server use a 9-pin,
D-shell connector.
5
1
6
9
Table 2 shows the pin-number assignments for the serial
port connectors. The pin-number assignments conform to
the industry standard.
Pin
Signal
Pin
Signal
1
2
3
4
5
Data carrier detect
Receive data
Transmit data
Data terminal ready
Signal ground
6
7
8
9
Data set ready
Request to send
Clear to send
Ring indicator
Table 2. Serial Port Connector Pin-Number Assignments
IBM Netfinity 3000 - Type 8476
89
Parallel port connector:
Parallel ports are used to
communicate with printers and other devices, such as
some CD-ROM and tape drives. The server provides one
25-pin, D-shell connector on the back of the server.
1
13
25
14
This parallel port connector conforms to the Institute of
Electrical and Electronics Engineers (IEEE) Standard 1284.
There are three standard modes of operation:
Ÿ
Ÿ
Ÿ
Standard Parallel Port (SSP)
Enhanced Parallel Port (EPP)
Extended Parallel Port (ECP)
Table 3 shows the pin-number assignments for the parallel
port connector. The signal names for all three modes are
shown. SSP and ECP signal names are the same; EPP
signal names that are different are shown in parentheses.
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
-STROBE (-WRITE)
Data 0
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
-ACK
BUSY (-WAIT)
PE
SLCT
14
15
16
17
18
19
20
21
22
23
24
25
-AUTO FD (-DSTRB)
-ERROR
-INIT
-SLCT IN (-ASTRB)
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Table 3. Parallel Port Connector Pin-Number Assignments
90
Netfinity Server HMM
External view
The following illustration shows the external view of the
server.
Note
This illustration is for reference only.
.1/
.2/
.3/
.4/
.5/
.6/
.7/
.8/
.9/
.1ð/
Power-on button
Power-on light
Hard disk drive light
Ethernet activity light
Bay 1, CD-ROM drive
CD-ROM eject button
CD-ROM emergency eject hole
Bay 2
Bay 3
Bay 4, 3.5-inch diskette drive
The server comes with a diskette drive installed in bay 4
and a CD-ROM drive installed in bay 1. If the server
comes with a hard disk drive, it is installed in bay 6.
Note
In some models, you might have to remove the front
bezel from the CD-ROM drive to access the
emergency-eject hole.
IBM Netfinity 3000 - Type 8476
91
Front fan
Attention
The presence of 5 V ac standby power might result in
damage to the hardware unless you disconnect the
power cord from the electrical outlet before you open
the server.
Note
Ÿ
Ÿ
Read “Safety information” on page 210
Read the documentation that comes with the
option.
To remove and replace the front fan:
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Position the server as described in “Accessing the
system board” on page 59.
3. Disconnect the front fan cable from the riser card.
See the label inside the server for the location of the
front fan connector, or see the riser-card illustration in
“ISA and PCI adapters” on page 61.
4. Press the tab and pull the front fan forward until it
clears the server wall.
Tab
Hooks
5. Replace the front fan by aligning the two hooks on
the bottom of the front fan assembly with the slots on
the server wall.
6. Insert the tab on the front fan assembly into the slot
on the server wall.
92
Netfinity Server HMM
7. Connect the front fan cable to the connector on the
riser card.
8. Replace the bottom cover (see “Bottom cover” on
page 71).
9. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
IBM Netfinity 3000 - Type 8476
93
Input/Output connectors
Input/output (I/O) connectors provide ports for transferring
information into and out of the server. You can connect a
variety of I/O devices to the server, including a monitor,
keyboard, mouse, and printer. For more information on
the ports and their specific technologies, see “External
options” on page 87.
At the rear of the server is a panel that provides access to
I/O connectors. Adapters installed in expansion slots
might also provide I/O connectors. The following
illustration shows the I/O connectors that come with the
server.
Power Connector
Expansion Slots
External SCSI Device
Microphone
Audio
Line In
Audio
Line Out
USB 1
ISA 3
ISA 1
ISA 2
USB 2
2
1
Serial 1
Serial 2
2
1
Keyboard
PCI 3
PCI 1
Parallel
PCI 2
Ethernet
(RJ-45)
Mouse
Monitor
Power Connector: The server power
cable connects here.
External SCSI Device Connector:
External SCSI devices attach here. For
more information, see “SCSI drives” on
page 104, “External SCSI devices” on
page 88, and “SCSI connectors” on
page 156.
94
Netfinity Server HMM
Expansion Slots: Cables to the external
connectors on installed ISA and PCI
adapters connect here. For information
about expansion slots and adapters, see
“Adapters” on page 60.
Note
The SCSI connector is located on the
SCSI adapter installed in slot 6.
Microphone: This connector is used to
attach a microphone to the server when
you want to record voice or other sounds
on the hard disk. This connector can also
be used by speech-recognition software.
Audio Line In: This connector is used to
send audio signals from an external
device (such as a CD player or stereo) to
the server so that the signals can be
recorded on the hard disk.
Audio Line Out: This connector is used
to send audio signals from the server to
external devices, such as stereo-powered
speakers with built-in amplifiers,
headphones, multimedia keyboards, or
the audio line-in jack on a stereo system.
To hear audio, you must connect one of
these external devices to the audio
line-out connector on the server.
Note
The internal speaker in the server is
disabled when an external speaker is
attached to the audio line-out
connector on the server. There is no
playback capability through the
internal speaker.
IBM Netfinity 3000 - Type 8476
95
Ethernet Connector: An unshielded,
twisted-pair (UTP) cable with an RJ-45
connector attaches here to the 10/100
Ethernet controller on the system board.
For information on the Ethernet controller,
see “Configuring the Ethernet controller”
on page 38. For more information on the
Ethernet connector, see “Ethernet
connector” on page 159. For information
on cables, see “Specifications (Ethernet
cable)” on page 53.
The server contains diagnostic
light-emitting diodes (LEDs) for the
Ethernet connector located on the rear
panel of the server.
Ÿ
Ÿ
When the green LED is on, it
indicates that the Ethernet controller
is connected to a hub or switch and
is receiving link pulses. This LED is
also known as the Link OK light.
When the amber LED is on, it
indicates that the Ethernet network is
operating at 100 Mbps. When this
LED is off, it indicates that the
Ethernet network is operating at 10
Mbps.
Parallel Connector: A signal cable for a
parallel device, such as a printer,
connects here.
Universal Serial Bus (USB)
Connectors: I/O devices with universal
serial bus (USB) connectors attach to
USB connector 1 and connector 2. You
need a 4-pin cable to connect a device to
these ports.
Serial Connectors: Signal cables for
modems or other serial devices attach to
the 9-pin serial connectors of serial ports
1 and 2. See “Serial port connectors” on
page 89 for port assignment information.
Mouse Connector: The mouse cable
connects here. This connector is
sometimes called the auxiliary-device
port.
Keyboard Connector: The keyboard
cable connects here.
Monitor Connector: The monitor signal
cable connects here.
96
Netfinity Server HMM
Internal drives
You can add drives to the server to increase storage
capacity and to enable the server to read multiple types of
media. Several types of drives are available, such as:
Ÿ
Ÿ
Ÿ
Ÿ
Diskette
Hard disk
Rewritable optical disc
Tape
Expansion bays:
Internal drives are installed in
bays at the front and rear of the server. The bays are
referred to as bay 1, bay 2, and so on.
Drive bays 1 through 4, at the front of the server, are
contained in the upper drive bracket. Drive bays 5 and 6,
at the rear of the server, are contained in the lower drive
bracket.
Note
A drive bracket is also known as a drive cage.
The server comes with the following preinstalled drives:
Ÿ
Ÿ
Ÿ
A 3.5-inch, 1.44 MB diskette drive in bay 4
A 3.5-inch, SCSI hard disk drive in bay 6 (in some
models)
A 5.25-inch, CD-ROM drive in bay 1
The following illustration shows the locations of the bays in
the server. This illustration shows the server front view,
with the side panel removed.
.1/
.2/
.3/
.4/
.5/
Bay
Bay
Bay
Bay
Bay
1
2
3
4
5
IBM Netfinity 3000 - Type 8476
97
.6/
Bay 6
The following is a detailed description of the drive bay
contents.
CD-ROM Drive: The server comes with an
integrated drive electronics (IDE) CD-ROM drive.
Open Bays: The server's design accommodates
3.5-inch and 5.25-inch devices, such as hard disk,
tape, and rewritable optical disk drives. The number
and capacities of the hard disk drives vary by model.
For information on the supported types of drives and
their installation, see “Drive specifications” on
page 99, “Preinstallation steps (all bays)” on
page 105, and http://www.ibm.com/pc/us/compat/ on
the World Wide Web.
Diskette Drive: The 3.5-inch, 1.44 MB2 diskette
drive uses 1 MB (unformatted) or 2 MB (unformatted)
diskettes.
2
MB equals approximately 1 000 000 bytes; total user-accessible
capacity may vary depending on operating environment.
98
Netfinity Server HMM
Drive specifications: Table 4 describes some of
the drive types that you can install in each bay, and their
width and height requirements.
Bays
1
Drive Widths
3.5-inch3
5.25-inch
2
3.5-inch3
5.25-inch
Drive Types
Drive Height
Removable
media4 drive,
hard disk drive
25.4 mm (1.0
in.)
CD-ROM drive
41.3 mm (1.6
in.)6
Removable
media4 drive,
hard disk drive
25.4 mm (1.0
in.)
41.3 mm (1.6
in.)6
3
3.5-inch
Hard disk drive5
25.4 mm (1.0
in.)
4
3.5-inch
Diskette drive
25.4 mm (1.0
in.)
5
and
6
3.5-inch
Hard disk drive5
25.4 mm (1.0
in.)
41.3 mm (1.6
in.)6,7
Table 4. Maximum Allowable Drive Sizes
3
4
5
6
7
To properly install a 3.5-inch drive in bay 1 or 2, use the
3.5-inch conversion kit for a 5.25-inch bay that is already
installed in bay 2. If you are installing a 5.25-inch drive in bay
2, you must first remove the conversion kit.
Removable media include CD-ROMs, optical discs, diskettes,
and tapes. If you install removable-media drives, you must
install them in bays 1–4 only. The server supports only one
diskette drive (standard in bay 4).
In some models, the CD-ROM drive might be set as the default
startup (or boot) drive. However, if a hard disk drive is
preinstalled, you can change the startup sequence, and specify
the hard disk drive as the startup drive. See “Start options” on
page 26 for information about changing the startup sequence.
Drives that are higher than 41.3 mm (1.6 in.) cannot be
installed.
One slim-high drive has a height of 25.4. mm (1.0 in.). One
half-high drive has a height of 41.3 mm (1.6 in.). Therefore,
you can install two slim-high drives or one half-high drive
between bays 5 and 6.
IBM Netfinity 3000 - Type 8476
99
Types of cables: The server uses cables to connect
IDE and SCSI drives to the power supply, riser card, and
system board. The diskette drive is also powered through
a cable attached to the riser card. Each cable connector is
designed to fit a corresponding drive connector. The
following cables are provided:
Ÿ
Ÿ
Ÿ
Four-wire power cables connect most drives to the
power supply. At the ends of these cables are plastic
connectors that attach to different drives; these
connectors vary in size. Also, some power cables
attach to the riser card.
Flat signal cables, sometimes called ribbon cables,
connect IDE drives to the riser card. There are two
sizes of signal cables that come with the server.
– The wider signal cable attaches to the primary
IDE connector on the back of the riser card.
– The narrower signal cable attaches to the
diskette drive and to the diskette drive connector
on the back of the riser card.
A flat SCSI signal cable for connecting devices to the
SCSI adapter.
Since the server is equipped with an UltraSCSI adapter, it
has a ribbon cable that is connected to the internal SCSI
hard disk drive. One end of this cable is connected to the
68-pin, internal SCSI connector on the SCSI adapter. The
other end of the SCSI cable has a terminator. This cable
provides four connectors for attaching other internal SCSI
devices.
For more information about SCSI devices, see “SCSI
drives” on page 104.
Note
To locate connectors on the system board, see
“System board illustration” on page 142.
100
Netfinity Server HMM
The diskette, IDE CD-ROM, and other IDE device
connectors are on the back of the riser card. When you
are installing optional drives, refer to the following
illustration for the location of the appropriate connectors.
Note
The following illustration is for reference only. Before
you install drives, be sure to check the orientation of
the server riser card for the correct connector
locations. The bottom edge of this card is located at
the back of the server.
Diskette Drive
Secondary IDE
LED Panel
Primary IDE
Power
IBM Netfinity 3000 - Type 8476
101
The following illustration shows the connectors on the riser
card.
ISA
Disk Fan A
Connector
Disk Fan B
Connector
ISA
ISA
Front Fan Connector
PCI
SCSI Hard Disk LED
Connector
Wake on LAN Connector
Asset ID Antenna
Connector
PCI
PCI
Chassis-Intrusion
Detector Connector
Internal Speaker
Connector
CD
Audio
Connector
340-Pin
Connector
Alert on LAN
Connector
Modem Wakeup
Connector
Notes
1. Alert on LAN and AssetID are available on some
models only.
2. If you attach a 4-position cable connector to the
2-pin Modem Wakeup connector, ensure that the
unused positions are next to the bottom of the
riser card, as shown in the illustration. If this
cable is incorrectly attached, the server might
automatically restart each time that you turn off
the power.
ISA
Disk Fan A
Connector
Disk Fan B
Connector
ISA
ISA
Front Fan Connector
PCI
SCSI Hard Disk LED
Connector
Wake on LAN Connector
Asset ID Antenna
Connector
Chassis-Intrusion
Detector Connector
PCI
PCI
Internal Speaker
Connector
CD
Audio
Connector
340-Pin
Connector
Alert on LAN
Connector
Modem Wakeup Connector
The following are some important points to remember
when connecting power and signal cables to internal
drives:
Ÿ
Ÿ
102
The diskette drive, hard disk drive (if applicable), and
CD-ROM drive that are preinstalled in the server
come with power and signal cables attached. The
CD-ROM drive is attached to the primary IDE
connector on the back of the riser card. If you
replace any drives, it is important to remember which
cable is attached to which drive.
When you install a drive, ensure that the connector at
the end of the signal cable is connected to the system
board.
Netfinity Server HMM
Ÿ
Ÿ
Ÿ
Ÿ
The CD-ROM drive and the diskette drive are the only
IDE devices that come with the server. You can
install another IDE device, such as a CD-ROM drive
or tape drive; however, IDE hard disk drives are not
supported.
If two or more IDE devices are used on a single
cable, one must be designated as the primary or
master device and all others as secondary or
subordinate devices; otherwise, some of the IDE
devices might not be recognized by the system. The
primary or secondary designation is determined by
switch or jumper settings on each IDE device.
In this server, the IDE CD-ROM drive is the primary
device. If you install a second IDE device, it must be
the secondary device.
You can install one diskette drive only.
If you plan to attach an internal SCSI drive, connect it
to one of the available connectors on the internal
SCSI cable.
Note
The SCSI cable provides termination.
If you plan to attach an external SCSI drive, see
“External options” on page 87 for additional
information.
For help in selecting drives, cables, and other options for
the server, do one of the following:
Ÿ
Ÿ
Ÿ
Within the United States, call 1-800-IBM-2YOU
(1-800-426-2968), your IBM reseller, or your IBM
marketing representative.
Within Canada, call 1-800-565-3344 or
1-800-465-7999.
Outside the United States and Canada, contact your
IBM reseller or IBM marketing representative.
IBM Netfinity 3000 - Type 8476
103
SCSI drives:
Some drives have a special design
called small computer system interface (SCSI). This
design allows you to attach multiple drives to a single
connector.
Note
Any information about SCSI drives also applies to
other SCSI devices, such as scanners and printers.
The Netfinity 3000 server supports drives that comply with
American National Standards Institute (ANSI) SCSI
Standards X3.131-1986 (SCSI), X3.131-1994, (SCSI-2),
X3.277-1996 (SCSI-3 Fast-20 parallel interface), and
X3.253-1995 (SCSI-3 parallel interface).
For a complete list of the SCSI devices that the server
supports, go to http://www.ibm.com/pc/us/netfinity/ on the
World Wide Web.
SCSI physical unit numbers: When more than one
physical device is connected to the same UltraSCSI
adapter, the devices compete for support from the
UltraSCSI adapter. Because the UltraSCSI adapter
communicates with only one device at a time, the priority
of a device is based on its SCSI identification (ID). The
highest priority IDs are 7 to 0; the lowest priority IDs are
15 to 8.
If you install additional SCSI devices, you must set a
unique ID for each SCSI device that you connect to the
integrated SCSI-2 connector. This unique ID enables the
UltraSCSI adapter to identify the devices and to prevent
two devices from sending or receiving data on the SCSI
bus at the same time. SCSI devices use a variety of
methods to set the SCSI ID, such as jumpers,
thumbwheels, or switches.
The SCSI device ID is also known as the SCSI address or
physical unit number (PUN).
The UltraSCSI adapter in the server supports SCSI IDs 0
to 15; ID 7 is reserved for the adapter. The default startup
(boot) SCSI ID is 0 for an internal SCSI hard disk drive in
Channel A. Use SCSISelect to view the SCSI IDs of SCSI
devices in the server. (See “SCSISelect utility program” on
page 49 for more information.)
If you install wide (16-bit) SCSI devices, you can set the
IDs to any number between 0 and 6, or between 8 and 15.
If you install narrow (8-bit) SCSI devices, you can set the
IDs to any number between 0 and 6.
SCSI logical unit number: Each physical device has
a physical unit number (PUN) and a logical unit number
(LUN). If a physical device supports no logical devices, its
LUN is 0. Most SCSI devices support only LUN 0.
104
Netfinity Server HMM
Certain types of physical SCSI devices (bridge controllers)
can support more than one logical device.
For example, a printer controller might support up to eight
printers. The printer controller is a physical device, and
each printer is a logical device. If the printer controller is
assigned to ID 2, the ID of the first printer appears in the
SCSI device configuration as PUN 2, LUN 0. The IDs of
the other printers are PUN 2, LUN 1; PUN 2, LUN 2; on up
to PUN 2, LUN 7.
Termination requirements: The Netfinity 3000 server
comes with an UltraSCSI adapter. The SCSI bus must be
terminated at both ends only. The UltraSCSI adapter
provides termination for one end of the SCSI bus (cable) in
the server. The SCSI cable in the server comes with a
terminator that provides termination for the other end of the
SCSI bus. Therefore, any internal SCSI devices that are
installed must have their termination set to Disabled.
When you install devices in bays 2, 3, 5, and 6, you
must disable the termination for the devices before
you install them.
If you connected external SCSI devices to the server,
set the termination for the last device on the external
cable to Enabled. See the device documentation for
instructions.
Ÿ
Ÿ
If you plan to install both 16-bit (wide) and 8-bit (narrow)
SCSI devices:
1. Attach the 16-bit devices at the beginning of the SCSI
chain.
2. Attach the 8-bit devices at the end of the SCSI chain.
Note
The beginning of the SCSI chain is the end closest to
the SCSI adapter or the system board.
This enables the UltraSCSI adapter to recognize all of the
devices in the SCSI chain, and thus ensures proper server
operation.
Refer to the instructions that come with the SCSI device
for more information about termination.
Preinstallation steps (all bays)
Before you begin, be sure you have:
Ÿ
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Read the documentation that comes with the
option.
Read “Termination requirements.”
Verified that you have all cables, drive trays, and
any other equipment specified in the
documentation that comes with the internal drive.
IBM Netfinity 3000 - Type 8476
105
Before you can install drives in the Netfinity 3000 server,
you might need to perform certain preinstallation activities.
Some of the steps are required only during the initial
installation of an option.
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Choose the bay in which you want to install the drive.
(Refer to Table 4 on page 99 for the drive types and
sizes available for each bay.)
3. Access the appropriate drive bays.
Notes
1. In all models, drive bays 1 and 4 come with
drives preinstalled.
2. In some models, drive bay 6 comes with a
drive preinstalled.
3. Drive bays 2 and 3 have a bay panel and
static shield installed.
4. If you remove a drive that has removable
media and you do not intend to install a new
drive immediately, reinstall the static shield
and bay panel for that bay.
To access drive bays 1 through 4, go to “Working
with drives in bays 1 through 4” on page 107.
To access drive bays 5 and 6, go to “Working with
drives in Bays 5 and 6” on page 121.
4. Touch the static-protective bag containing the drive to
any unpainted metal surface on the server; then,
remove the drive from the bag.
5. Check the instructions that come with the drive, or
contact your IBM reseller or IBM marketing
representative to see if you need to set any switches
or jumpers on the drive, or if you need to attach a
tray to the drive.
106
Netfinity Server HMM
Working with drives in bays 1 through 4:
There are two different designs for the front drive cage that
contains drive bays 1 through 4. One design has a drive
cage that must be removed when you install or remove
drives. With the other design, you install drives from the
front of the server without removing the drive cage. In this
type, the drive cage is permanently mounted to the chassis
and cannot be removed. To determine which type of
chassis you have, look for the support bracket and screw
that secure the front drive cage. If the chassis does not
have these components, you have the permanently
mounted drive cage. The procedure for installing and
removing drives is different for each type of chassis.
The following illustration shows the server bays.
.1/
.2/
.3/
.4/
.5/
.6/
Bay
Bay
Bay
Bay
Bay
Bay
1
2
3
4
5
6
Note
The front drive cage is also known as the upper drive
cage.
Attention
The presence of 5 V ac standby power might result in
damage to the hardware unless you disconnect the
power cord from the electrical outlet before you open
the server.
IBM Netfinity 3000 - Type 8476
107
Note
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Read the instructions that come with the drive
that you want to install or replace.
Position the server as described in “Accessing
the system board” on page 59.
If the server has the permanently mounted drive
cage, go to “Installing drives in the permanently
mounted drive cage” on page 108.
If the server has the removable drive cage, go to
“Removing the removable drive cage” on
page 114.
Installing drives in the permanently mounted
drive cage: This section gives the procedure for
installing drives in the permanently mounted front drive
cage. If you want to remove a drive from the upper drive
cage, follow the steps in “Removing drives in the
permanently mounted drive cage” on page 112.
Note
Ÿ
Ÿ
Read “Working with drives in bays 1 through 4”
on page 107.
Read the documentation that comes with the
drive.
1. Remove the bay panel for the drive bay where you
are installing the drive.
a. Locate the appropriate bay panel in the front of
the server.
b. Use the tip of a screwdriver, if necessary, to
release the plastic tabs that hold the bay panel
at the front of the server.
108
Netfinity Server HMM
c. Remove the bay panel.
2. If knockouts are present in the drive bay opening,
twist them with a screwdriver or pliers to remove.
The following illustration shows the type of knockout
in bays 2 and 3.
IBM Netfinity 3000 - Type 8476
109
3. Install the drive in the bay opening and secure the
drive by inserting screws.
Note
As shown in the following illustration, only two
screws are needed to secure the drive within the
drive bay.
4. Attach the cables to the drive. See “ISA and PCI
adapters” on page 61 for an illustration that shows
the locations of the connectors on the riser card.
110
Netfinity Server HMM
5. If the installed drive has nonremovable media, replace
the bay panel.
6. If you installed a CD-ROM drive and want to connect
the drive to the CD-ROM audio connector, see “ISA
and PCI adapters” on page 61 to locate the CD-ROM
audio connector on the riser card.
7. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
IBM Netfinity 3000 - Type 8476
111
Removing drives in the permanently mounted
drive cage: This procedure is for those servers that
have a permanently mounted front drive cage.
1. If the drive being removed has nonremovable media,
remove the bay panel.
a. Locate the appropriate bay panel in the front of
the server.
b. Use the tip of a screwdriver, if necessary, to
release the plastic tabs that hold the bay panel
at the front of the server.
c. Remove the bay panel.
112
Netfinity Server HMM
2. Disconnect the cables from the drive that you want to
remove.
3. Remove the visible screws that hold the drive and
slide it out the front of the server.
4. If you are not installing another drive, replace the bay
panel.
5. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
IBM Netfinity 3000 - Type 8476
113
Removing the removable drive cage: The
following illustration shows a chassis with a drive-support
bracket and a removable drive cage. The front drive cage
is also known as the upper drive cage.
Front
Drive
Cage
Drive
Support
Bracket
To remove the drive cage:
1. Disconnect any cables that are connected to drives in
bays 1 through 4.
114
Netfinity Server HMM
2. Remove the top-handle cover and set it aside.
3. Remove the top-handle screw and the screw from the
drive-support bracket that holds the upper drive cage
in place. Then, move the drive cage towards the
power supply until it stops, and lift it out of the server.
7 tekco S
7 tekcoS
IBM Netfinity 3000 - Type 8476
115
Installing a drive in the removable drive cage:
This section gives the procedure for installing drives in the
upper drive cage. If you want to remove a drive from the
upper drive cage, reverse the order of the following steps.
Note
Ÿ
Ÿ
Ÿ
Read “Working with drives in bays 1 through 4”
on page 107.
Read the documentation that comes with the
drive.
Remove the drive cage. See “Removing the
removable drive cage” on page 114.
1. With the front of the drive cage facing you, remove
the metal shield for the drive bay you want to use by
pulling out the tabs on the sides of the shield until it
flexes. Lift off one side, then the other.
2. Touch the static-protective package containing the
new drive to any unpainted metal surface; then,
remove the drive from it.
116
Netfinity Server HMM
3. Insert the drive into the desired unoccupied drive bay.
Insert and tighten the screws that hold it in place.
The following illustration shows a hard disk drive
being installed in bay 2.
4. Insert the drive cage and slide it to the right until it
stops at the front of the server; be sure that the screw
holes in the drive cage are aligned with the screw
holes in the support bracket.
5. Insert and tighten the screw that secures the drive
cage at the side; then, tighten the screw on top near
the handle.
7 tekcoS
7 tekcoS
IBM Netfinity 3000 - Type 8476
117
6. Replace the top-handle cover.
7. Attach the cables to the drive, as shown in the
following illustration.
8. If you have installed a drive with removable media,
you must remove the bay panel. If you have installed
a drive with nonremovable media, you must install a
bay panel (if it was not already installed).
Ÿ To remove a bay panel, go to step 9 on
page 119.
Ÿ To install a bay panel, go to step 10 on
page 120.
118
Netfinity Server HMM
9. To remove a bay panel:
a. Locate the appropriate bay panel in the front of
the server.
b. Use the tip of a screwdriver, if necessary, to
release the plastic tabs that hold the bay panel
at the front of the server.
c. Remove the bay panel.
d. Continue with step 11 on page 120.
IBM Netfinity 3000 - Type 8476
119
10. To install a bay panel:
a. Align the right-hand edge of the bay panel with
the matching opening in the front of the server.
b. Gently press the left edge closed until it snaps.
c. If you installed a CD-ROM drive and want to
connect the drive to the CD-ROM audio
connector, see “ISA and PCI adapters” on
page 61 to locate the CD-ROM audio connector
on the riser card.
d. Go to “Installing a drive in the removable drive
cage” on page 116.
11. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
120
Netfinity Server HMM
Working with drives in Bays 5 and 6
Notes
Ÿ
Ÿ
Read “Working with drives in bays 1 through 4”
on page 107.
Read the documentation that comes with the
drive.
The following illustration identifies the server bays.
.1/
.2/
.3/
.4/
.5/
.6/
Bay
Bay
Bay
Bay
Bay
Bay
1
2
3
4
5
6
The drives in bays 5 and 6 must have nonremovable
media. (In some models, the server comes with a hard
disk drive in bay 6.) To install or remove drives in these
bays, you must remove the rear (lower) drive cage.
IBM Netfinity 3000 - Type 8476
121
To install or remove drives in bays 5 and 6:
1. Remove the screw that holds the drive cage, and
carefully slide the drive cage past the cover lock and
out.
2. If there is a hard disk drive in bay 6, disconnect the
cable from the drive in that bay. If there is a drive in
bay 5, disconnect its cable.
3. If you are removing a drive, remove the screws that
hold the drive in the cage and slide the drive out of
the cage.
122
Netfinity Server HMM
4. If you are installing a drive in bay 5, turn the drive
upside down before you slide it into the bay. This
ensures that the drive connector will align with and
attach properly to the cable connector.
When you install the four screws that come with the
drive, attach them to the drive from the top.
The following illustration shows a drive being installed
in bay 5.
5. If you are installing a drive in bay 6, turn the drive
upside down before you slide it into the bay. This
ensures that the drive connector will align with and
attach properly to the cable connector.
If the server comes with a drive installed in bay 6, two
screws are attached to each side of the drive
assembly. Therefore, if you remove a drive from bay
6 and install another drive in that bay, use the screws
that come with the preinstalled drive.
Note
When using the rubber grommets (washers) to
attach the drive to the rear drive cage, you must
use the screws provided in the tray in bay 2.
IBM Netfinity 3000 - Type 8476
123
6. Reinstall the rear drive cage and secure it with the
screw that you removed in step 1 on page 122.
7. Attach the cables to the drive, as shown in the
following illustration.
8. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
124
Netfinity Server HMM
Internal view
The following illustration shows the internal view of the
server, with the side panel removed.
Note
The following illustration is for reference only.
.1/
.2/
.3/
.4/
.5/
.6/
.7/
.8/
.9/
Drive cage for bays 1 through 4
System board
Riser card
Adapter
Expansion slots
Drive cage for bays 5 and 6
Bay 6, hard disk drive
Bay 5
Power supply
IBM Netfinity 3000 - Type 8476
125
Memory modules
Adding system memory to the server can make programs
run faster. You can increase the amount of system
memory by installing options called memory modules.
The maximum amount of system memory the server
supports is 384 MB. You can add memory to the server to
increase system performance. The server has three
connectors for installing system memory modules.
Note
The following illustration is for reference only. Before
you install memory, be sure to check the orientation of
the server system board for the correct connector
locations.
To locate the memory connectors on the system
board, see “System board illustration” on page 142.
DIMM 0
DIMM 1
DIMM 2
The memory modules that the server uses are dual-inline
memory modules (DIMMs). The DIMMs that come with
the server are synchronous dynamic random-access
memory (SDRAM) with error checking and correction
(ECC). These memory modules have a speed of 100
MHz. You can add extra memory modules or replace
existing memory modules.
When installing or replacing DIMMs, follow these
guidelines:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
126
The server comes with one or more dual-inline
memory modules (DIMMs) installed.
Install DIMMs with a maximum height of 6.35 cm
(2.5 inches).
Use only 3.3 V dc unbuffered, 100 MHz SDRAM
DIMMs.
Each memory connector supports a maximum of 128
MB of memory. However, the maximum amount of
system memory the server supports is 384 MB.
Install only ECC DIMMs to enable ECC. If you install
nonparity (NP) DIMMs, the server will not power up,
and POST memory error code 164 will be displayed.
If you are installing DIMMs of different sizes, install
the DIMMs with greater memory capacity starting with
the connector closest to the edge of the system board
(DIMM 2).
After installing or removing a DIMM, you must save
the new configuration information using the
Configuration/Setup Utility program. See
Netfinity Server HMM
“Configuration/Setup utility program menus” on
page 24.
For more information about the DIMMs that the server
supports, go to the following World Wide Web
address:
Ÿ
http://www.ibm.com/pc/us/compat/
Memory configuration:
When you are adding or
removing memory, fill each system memory connector
sequentially, starting at DIMM 0.
Table 5 shows the some of the possible memory
configurations for the server. The contents of this table
and additional information can be found on a label located
inside the server. Alternative configurations are possible.
Table 5. Memory Configurations
Total Memory (MB)
32
64
64
96
96
128
128
128
192
256
256
384
DIMM 0
DIMM 1
DIMM 2
32
64
32
64
32
128
64
64
64
128
128
128
0
0
32
32
32
0
32
64
64
64
128
128
0
0
0
0
32
0
32
0
64
64
0
128
Note
The values in Table 5 on page 127 are represented
in megabytes (MB).
Installing or removing memory modules:
This section gives the procedure for installing memory
modules. If you want to remove a memory module,
reverse the order of the following steps.
Before you begin:
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Read the documentation that comes with the
option.
Read “Accessing the system board” on page 59.
IBM Netfinity 3000 - Type 8476
127
Notes
1. When you are removing a memory module, be
careful not to push too hard on the retaining clips
because the memory module might abruptly eject
from the connector.
2. Each memory connector contains two keys
(dividers), which are used to assure that a
memory-module can be installed only in the
correct position.
3. A retaining clip at each end of the connector
locks the memory module into place.
4. For information about memory configuration, see
Table 5.
To install a DIMM:
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Locate the memory connectors on the system board.
See the illustration at the beginning of this section.
3. Be sure that the retaining clips are in the open
position, as shown in the following right-hand
illustration. If the retaining clips are perpendicular to
the connector, push outward on them until they click
open.
4. Touch the static-protective package containing the
DIMM to any unpainted metal surface in the server;
then, remove the DIMM.
5. Position the DIMM above the connector so that the
two notches on the bottom edge of the DIMM align
properly with the connector.
6. Firmly push the DIMM straight down into the
connector until the retaining clips close and snugly fit
around both ends of the DIMM.
128
Netfinity Server HMM
Notches
Note
Adding or removing DIMMs changes the
configuration information in the server. When
you restart the server, the system displays POST
error 164. Start the Configuration/Setup Utility
program and select Save Settings.
7. To install another DIMM, repeat steps 3 through 6 on
page 128.
8. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
IBM Netfinity 3000 - Type 8476
129
Microprocessors
The server comes with an Intel Pentium II microprocessor.
This microprocessor incorporates MMX technology with
built-in ECC level-2 (L2) cache. For the latest information
about microprocessor upgrades available for the server,
contact your IBM reseller or IBM marketing representative.
If you do upgrade the microprocessor, use the instructions
that come with the upgrade along with the instructions in
“Installing or replacing microprocessors” on page 131.
The voltage regulator function is built into the system
board. This feature supports the microprocessor on the
system board.
Note
The illustrations in this section might differ slightly from
the hardware.
130
Netfinity Server HMM
Installing or replacing microprocessors:
This section gives the procedure for installing
microprocessors. If you want to remove a microprocessor,
reverse the order of the following steps.
Notes
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Thoroughly review the documentation that comes
with the microprocessor, so that you can
determine whether you need to update the server
BIOS. ServerGuide includes IBM Update
Connector, which keeps the BIOS and device
drivers current. You can also obtain the latest
level of BIOS for the server through the World
Wide Web and the IBM Personal Computer
Company Bulletin Board System (BBS). See
“Online support” on page iv for the appropriate
World Wide Web addresses and bulletin board
telephone numbers.
For a list of supported operating systems, see
http://www.ibm.com/pc/us/netfinity/ on the World
Wide Web.
Read “Accessing the system board” on page 59.
Locate the Flash Utility Diskette that you created
in “Remote administration” on page 34.
Note
If you have not already done so, go to
http://www.ibm.com/support/ on the World Wide Web
and download the appropriate flash update program.
Review the applicable README files, and use this
information to create a Flash Utility Diskette. Perform
the POST/BIOS (flash) update procedure (see
“Remote administration” on page 34 for additional
information).
Attention:
If you select a setting for the frequency switch that is
greater than the actual frequency of the microprocessor,
you might damage the microprocessor.
IBM Netfinity 3000 - Type 8476
131
Notes
1. The microprocessor in the server comes with an
attached heat sink. The microprocessor plugs
into the microprocessor socket on the system
board and is stabilized with a plastic bracket
attached to the system board. This bracket is
referred to as a goalpost.
The type of heat sink in the server might be
different from the heat sink shown in this section.
2. To locate the microprocessor switch area of the
system board, find the rocker switches section of
the system board illustration. See “System board
illustration” on page 142. For information about
the appropriate switch settings, see
“Microprocessor speed switches settings” on
page 153, or see the label inside the server.
To install a microprocessor:
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Remove the microprocessor:
a. Locate the microprocessor socket on the system
board. (See the illustration in “System board
illustration” on page 142.)
b. Place your index fingers on the small retainer
tabs on the top of the microprocessor. Push in
toward the microprocessor until the tabs release.
Tabs
132
Netfinity Server HMM
c. Lift the microprocessor out of the connector.
d. Store the old microprocessor in a
static-protective package.
e. Go to step 3 to install the replacement
microprocessor.
3. Touch the static-protective package that contains the
new microprocessor to any unpainted metal surface in
the server; then, remove the new microprocessor.
IBM Netfinity 3000 - Type 8476
133
4. Press in on the retainer tabs until they click into
place.
Note
For the location of the retainer tabs, see the
illustration in step 2b on page 132.
5. Align the new microprocessor with the microprocessor
connector on the system board and slide it into the
guides. Press the microprocessor down until it snaps
into place and is fully seated in the connector.
134
Netfinity Server HMM
6. Pull outward on the retainer tabs.
7. If you replace the microprocessor with one that has a
different speed, you might have to change the switch
settings on the system board. To locate the switches,
see “System board illustration” on page 142. For
information about the appropriate switch settings, see
“Microprocessor speed switches settings” on
page 153, or see the label inside the server side
cover.
8. If you receive the error code 167 after you install a
new microprocessor, run the Flash Utility program.
Insert the Flash Utility Diskette into the primary
diskette drive and run the flash program. Follow the
instructions in the program.
Note
If you have not already done so, go to
http://www.ibm.com/support/ on the World Wide
Web and download the appropriate flash update
program. Review the applicable README files,
and use this information to create a Flash Utility
Diskette. Perform the POST/BIOS (flash) update
procedure (see “Remote administration” on
page 34 for additional information).
9. Because you installed a new microprocessor in the
server, you must reconfigure the server. Follow the
procedure described in “Configuration/Setup utility
program menus” on page 24.
Refer to the operating-system documentation. You
might need to make changes so that the operating
system recognizes the new microprocessor.
10. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
IBM Netfinity 3000 - Type 8476
135
Preliminary option installation
information
Become familiar with the safety and handling
guidelines specified under “Safety information” on
page 210. These guidelines will help you work safely
while working with the server and options.
Make sure that you have an adequate number of
properly grounded electrical outlets for the server,
monitor, and any other options you intend to install.
Place the server in a location that is dry. Rain or
spilled liquids might damage the server.
Have a supply of 2 MB (1.44 MB formatted), 3.5-inch
diskettes available.
Back up all important data before you make changes
to hard disk drives.
Have a small, flat-blade screwdriver available.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Attention
To allow for air circulation, be sure to maintain the
following minimum clearances around the server:
Ÿ
Ÿ
Ÿ
102 mm (4 in.) in the front
127 mm (5 in.) in the rear
51 mm (2 in.) on the left and right sides
Before you begin:
Ÿ
Ÿ
Be sure that the current server configuration is
working properly.
If you have not already done so, locate the keys
to the cover lock. At the time of shipment, two
keys are attached to the back of the server, over
the keylock. Store the keys in a safe place.
Caution
When unlocked, the server door will not support the
weight of the server. To avoid personal injury, be sure
to remove or lock the server door before moving or
lifting the server.
k32 kg (70.5 lbs)
136
Netfinity Server HMM
k55 kg (121.2 lbs)
Caution
Use safe lifting practices when lifting the machine.
IBM Netfinity 3000 - Type 8476
137
Stabilizing feet
The four feet attached to the bottom cover rotate 90
degrees to provide additional stability for the server.
Before you place the server in an upright position, rotate
the four feet a quarter turn away from the server. Then,
carefully position the server on its feet.
When you need to access the inside of the server to install
options, you might find it easier to place the server on its
side, so that the system board is facing you. If you do so,
rotate the feet in towards the server, so that they do not
detach due to the weight of the server.
138
Netfinity Server HMM
System board
Attention
The presence of 5 V ac standby power might result in
damage to the hardware unless you disconnect the
power cord from the electrical outlet before you open
the server.
Note
Ÿ
Ÿ
Read “Safety information” on page 210.
Read the documentation that comes with the
option.
To install an adapter, you might have to remove the
system board.
To remove the system board:
1. Remove the server side cover (see “Disconnecting
cables and removing the side cover” on page 84).
2. Position the server as described in “Accessing the
system board” on page 59.
3. Remove the bottom cover. (See “Bottom cover” on
page 71.)
4. Loosen, but do not remove the riser card mounting
screw.
5. Lift the system board latch handle upward to
disconnect the plastic tab on the bottom of the handle
from the chassis.
IBM Netfinity 3000 - Type 8476
139
6. Grasp and turn the latch clockwise to the extended
position. This releases the system board from the
riser card.
Note
Do not pull on the microprocessor, the DIMMs, or
the DIMM sockets to remove the system board.
System Board
System Board
Rail
Latch
Tab
Lift
Here
Pull
Here
7. Using the tab, slide the system board out and set it
aside.
To reinstall the system board:
1. Make sure that the system board latch handle is in
the extended position.
2. Align the system board rails with the tracks on the
chassis and slide the board in until it is approximately
6 mm (0.25 in) from the riser-card edge connector.
3. Rotate the latch handle counterclockwise until the the
system board is properly aligned with the riser-card
edge connector.
4. Continue rotating the latch handle counterclockwise
while firmly pushing on the system board rail on the
right-hand side of the system board.
Note
Do not push on the microprocessor, the DIMMs,
or the DIMM sockets to install the system board.
Make sure that the system board is fully seated in the
riser-card edge connector.
140
Netfinity Server HMM
5. Re-tighten the riser card mounting screw.
6. Push down on the latch to lock the tab on the
underside in the opening (hole) in the chassis. This
securely holds the latch in the closed position.
Hole
System Board
Push
Here
Tab
Alignment
Mark
Note
You cannot see the connection with a full-sized
adapter in place. To make sure that the system
board is fully seated, lock the tab on the
underside of the system board latch in the
opening (hole) in the chassis.
7. If you want to install or remove any other options, do
so now. Otherwise, go to “Completing the
installation” on page 77.
IBM Netfinity 3000 - Type 8476
141
System board illustration
The system board, also called the planar or motherboard,
is the main circuit board in the server. It provides basic
server functions and supports a variety of devices that are
preinstalled or that you can install later.
Some configuration actions are controlled through jumpers
on the system board, whereas other actions are controlled
through switches. The following sections discuss the
jumper and switch settings that you can change.
If you plan to install, remove, or replace hardware in the
server, or if you must set jumpers and switches, you will
need to know the layout of the system board. The
following illustration shows the layout of the system board
in the server. The numbered pointers show the
components that are discussed in this book.
Notes
1. An illustration of the system board and additional
information are provided on a label inside the
server.
2. The configuration switches (1–8) are also known
as rocker switches. Their settings are specified
later in this chapter.
.1/
.2/
142
Battery
Configuration (rocker) switches (SW1)
Switches 1–4
Microprocessor speed
Switch 5
ROM operation mode
Switch 6
Ethernet controller operation mode
Switch 7
Administrator password
Netfinity Server HMM
.3/
.4/
.5/
.6/
.7/
.8/
Switch 8
Diskette write-protect
Microprocessor
DIMM Connector 0
DIMM Connector 1
DIMM Connector 2
Clear CMOS Request jumper (J9)
AGP slot connector for optional AGP adapter
IBM Netfinity 3000 - Type 8476
143
System board replacement
Attention
1. The vital product data (VPD) and latest level of
BIOS for the system you are servicing must be
installed on the new system board. To do this,
you must run the Flash Update program using
the Flash Update diskette. Obtain the latest level
of BIOS from the BBS/WEB, see “Online support”
on page iv. A down level BIOS may cause false
error and unnecessary replacement of the system
board.
2. The processor and memory modules are
separate FRUs. Remove them from the old
system board and install them on the new one.
3. Be sure the new system board jumper settings
match the old system board jumper settings.
If replacing the system board doesn't correct the problem,
do the following:
1. Reinstall the options (processor, etc) on the old
system board and reinstall it in the system.
2. Replace the processor.
144
Netfinity Server HMM
Switch settings
Administrator password switch setting:
When you want to set, change, or delete an administrator
password that is protected by enhanced security, you must
first unlock the administrator password. To do this, change
the setting of the administrator password switch from
Locked to Unlocked.
Before you begin:
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210
Power-off the server and all other connected
devices.
Disconnect all external cables attached to the
server; then, remove the server cover.
1. Locate the configuration switches (also known as
rocker switches) on the system board. For more
information, refer to the label inside the server, or see
“System board illustration” on page 142.
2. To lock or unlock the administrator password, set
switch 7 as shown in the following illustration. It
might be helpful to use the end of a small screwdriver
to set the switch.
Attention:
The following illustration is for reference only. Before
you change the settings for switch 7, be sure that you
check the orientation of the server system board to
correctly identify the switch number locations. If you
change the settings for the wrong switches, you might
seriously damage server components or options.
Administrator Password Locked
1 2 3 4 5 6 7 8
Administrator Password Unlocked
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
3. Move the switch to the ON position.
Note
You must know the administrator password to
change or delete it.
4. Set, change, or delete the password. Follow the
instructions on the screen. (See “Using the
administrator password menu” on page 31.)
5. Move the switch back to the OFF position.
6. Replace the cover. Then, power-on the server.
7. After changing configuration switch settings, you must
reconfigure the server. After reassembling the server
(see “Completing the installation” on page 77), use
the Configuration/Setup Utility program to set a new
IBM Netfinity 3000 - Type 8476
145
administrator password and reconfigure the server.
For more information, see “Configuration/Setup utility
program menus” on page 24.
Note
For more information on enhanced security, see
“Using the enhanced security features” on page 32.
146
Netfinity Server HMM
Diskette write-protect switch setting: The
diskette write-protect switch controls whether you can write
information to a diskette using a diskette drive. The ability
to prevent writing to a diskette is particularly useful if you
are concerned about the security of information that can be
obtained through a network.
Note
This switch does not affect the ability to read
information from a diskette.
Notes
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Power-off the server and all other connected
devices.
Disconnect all external cables attached to the
server; then, remove the server cover.
1. Locate the configuration switches (also known as
rocker switches) on the system board. For more
information, refer to the label inside the server, or see
“System board illustration” on page 142.
2. For normal diskette operation or for read-only diskette
operation, set switch 8 as shown in the following
illustration. It might be helpful to use the end of a
small screwdriver to set the switch.
Attention:
The following illustration is for reference only. Before
you change the settings for switch 8, be sure that you
check the orientation of the server system board to
correctly identify the switch number locations. If you
change the settings for the wrong switches, you might
seriously damage server components or options.
Normal Diskette Operation
1 2 3 4 5 6 7 8
Read-Only Diskette Operation
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
3. After changing configuration switch settings, you must
reconfigure the server. After reassembling the server
(see “Completing the installation” on page 77), use
the Configuration/Setup Utility program to reset the
date and time, reset any passwords, and reconfigure
the server. For more information, see
“Configuration/Setup utility program menus” on
page 24.
IBM Netfinity 3000 - Type 8476
147
Note
To control and specify who has access to the
diskettes in the server, use the Configuration/Setup
Utility program. Follow the instructions in “Restricting
access to IDE devices and diskette drives” on
page 33.
148
Netfinity Server HMM
Ethernet controller operation mode switch
setting: When you want to change the Ethernet
controller operation mode from Normal to MAC Disabled,
you must change the setting of configuration switch 6.
Notes
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210.
Power-off the server and all other connected
devices.
Disconnect all external cables attached to the
server; then, remove the server cover.
1. Locate the configuration switches (also known as
rocker switches) on the system board. For more
information, refer to the label inside the server, or see
“System board illustration” on page 142.
2. To set the Ethernet controller operation mode to the
appropriate value, set switch 6 as shown in the
following illustration. It might be helpful to use the
end of a small screwdriver to set the switch.
Attention
The following illustration is for reference only.
Before you change the settings for switch 6, be
sure that you check the orientation of the server
system board to correctly identify the switch
number locations. If you change the settings for
the wrong switches, you might seriously damage
server components or options.
Note
In the following illustration, MAC represents
medium access control. This refers to the
Ethernet controller address.
Ethernet Normal Operation
1 2 3 4 5 6 7 8
Ethernet MAC Disabled
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
3. Move the switch to the ON position.
4. Make the required adjustments to the Ethernet
controller address.
5. Move the switch back to the OFF position.
6. After changing configuration switch settings, you must
reconfigure the server. After reassembling the server
(see “Completing the installation” on page 77), use
the Configuration/Setup Utility program to reconfigure
the server. For more information, see
“Configuration/Setup utility program menus” on
page 24.
IBM Netfinity 3000 - Type 8476
149
Updating the server configuration
Attention
The configuration information in this section applies to
installing options. For more information on using the
Configuration/Setup Utility program, see
“Configuration/Setup utility program menus” on
page 24.
When you start the server for the first time after you add,
remove, or replace an internal option or an external SCSI
device, a message might appear, indicating that the
configuration has changed. The configuration settings
must be updated. This reconfiguration is performed
automatically by the server or manually by you. When the
server automatically configures an option, it uses system
programs. However, you must save the new settings
through the Configuration/Setup Utility program. If the
system programs do not update the settings, you can use
the Configuration/Setup Utility program to reconfigure the
appropriate settings.
For example, when you start the server after adding
memory or after adding most internal hard disk drives, the
settings are automatically updated, and you use the
Configuration/Setup Utility program to save those changes.
However, if a resource conflict arises after an ISA legacy
adapter is installed or removed, you must manually update
the server configuration and save the information.
150
Netfinity Server HMM
Notes
1. If an error message related to the
chassis-intrusion detector appears after you
restart the server, you must enter the
administrator password. Note that chassis
intrusion can be detected only if the
chassis-intrusion detector feature is activated,
which occurs when enhanced security is enabled
and an administrator password is set.
2. If you remove a SCSI device, the server might
not recognize any SCSI devices that are still
connected.
3. To run the Configuration/Setup Utility program,
follow the instructions in “Configuration/Setup
utility program menus” on page 24.
4. When you add a hard disk drive and you want to
include it in the startup sequence, use the Start
Options selection of the Configuration/Setup
Utility program (see “Start options” on page 26).
5. When you install an ISA legacy adapter, you
must allocate system resources to support it (see
“ISA legacy resources” on page 36).
6. Make a record of all customized settings before
you make any changes.
7. For more information handling resource conflicts,
see “Configuration conflicts” on page 20.
Record the new configuration information.
You might need to install device drivers after you install or
replace options, or after you update the configuration
settings. See the instructions that come with the option to
determine if device drivers are required, and, if so, how to
install them. In most situations, ServerGuide automatically
installs the device drivers during the operating system
installation process. Also, the video, SCSI, and Ethernet
device drivers are on the IBM ServerGuide CDs. Refer to
the ServerGuide documentation for instructions on
configuring hardware and installing a network operating
system.
If you do not need to install any device drivers, or update
or save the system configuration, the server is ready to
use.
IBM Netfinity 3000 - Type 8476
151
Video port connector
The video port is where you can attach a video monitor to
the Netfinity 3000 server. The server provides a 15-pin
video port connector.
6
1
11
5
15
10
Table 6 shows the pin-number assignments for the video
port connector.
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red
Green or monochrome
Blue
Not connected
Ground
Red ground
Green ground or monochrome ground
Blue ground
Reserved
Ground
Not connected
Display data channel (DDC data)
Horizontal synchronization (Hsync)
Vertical synchronization (Vsync)
Display data channel (DDC clock)
Table 6. Video Port Connector Pin-Number Assignments
152
Netfinity Server HMM
Microprocessor speed switches settings:
When you replace a microprocessor with one that has a
different speed8, you might have to change the switch
settings on the system board.
Before you begin:
Ÿ
Ÿ
Ÿ
Ÿ
Read “Safety information” on page 210
Power-off the server and all other connected
devices.
Disconnect all external cables attached to the
server; then, remove the server cover.
Locate the Flash Utility Diskette that you created
in “Remote administration” on page 34.
Note
If you have not already done so, go to
http://www.ibm.com/support/ on the World Wide Web
and download the appropriate flash update program.
Review the applicable README files, and use this
information to create a Flash Utility Diskette. Perform
the POST/BIOS (flash) update procedure (see
“Remote administration” on page 34 for additional
information).
1. Locate the configuration switches (also known as
rocker switches) on the system board. For more
information, refer to the label inside the server, or see
“System board illustration” on page 142.
2. To set the appropriate microprocessor speed, set
switches 1 to 4 as shown in the following illustration.
It might be helpful to use the end of a small
screwdriver to set the switch.
Note
Switches 5 to 8 are not used for microprocessor
speed settings.
Attention
The following illustration is for reference only.
Before you change the settings for switches 1
through 4, be sure that you check the orientation
of the server system board to correctly identify
the switch number locations. If you change the
settings for the wrong switches, you might
seriously damage server components or options.
8
MHz denotes internal clock speed of the microprocessor only;
other factors also affect application performance.
IBM Netfinity 3000 - Type 8476
153
266 MHz
1 2 3 4 5 6 7 8
300 MHz
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
350 MHz
1 2 3 4 5 6 7 8
400 MHz
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
450 MHz
1 2 3 4 5 6 7 8
500 MHz
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
550 MHz
1 2 3 4 5 6 7 8
600 MHz
1 2 3 4 5 6 7 8
ON
ON
OFF
OFF
Table 7. Microprocessor Switch Settings
450MHz and Up
All microprocessors of speed 450MHz and up will
automatically set their internal speeds, so the switch
setting is not applicable.
3. If you receive the error code 167 after you install a
new microprocessor, run the Flash Utility program.
Insert the Flash Utility Diskette into the primary
diskette drive and reboot the system. Follow the
instructions in the program.
4. After changing configuration switch settings, you must
reconfigure the server. After reassembling the server
(see “Completing the installation” on page 77), use
the Configuration/Setup Utility program to reconfigure
the server. For more information, see
“Configuration/Setup utility program menus” on
page 24.
154
Netfinity Server HMM
Keyboard and mouse connectors:
The server
provides one keyboard port and one auxiliary-device port.
An auxiliary device can be a mouse or other pointing
device. The server provides two 6-pin port connectors.
6
5
4
3
2
1
Table 8 shows the pin-number assignments for the
keyboard and auxiliary-device port connectors.
Pin
Signal
1
2
3
4
5
6
Data
Not connected
Ground
+5 V dc
Clock
Not connected
Table 8. Keyboard and Auxiliary-Device Port Connectors
Pin-Number Assignments
IBM Netfinity 3000 - Type 8476
155
SCSI connectors: The server comes with a 16-bit
UltraSCSI adapter. This adapter has two 68-pin,
high-density connectors (one internal and one external).
You can use these connectors to install internal SCSI
devices in the server and to attach external SCSI devices
to the server.
Note
The 50-pin SCSI connector is not supported.
See “SCSI drives” on page 104 for additional information
about the SCSI subsystem.
Internal SCSI connector: A 4-drop, 68-pin (16-bit)
cable is installed in the server. This cable is connected to
the internal connector for the 16-bit UltraSCSI adapter.
You can use this cable to install additional SCSI devices in
the server. A hard disk drive might also be installed in bay
6, depending on the model of the Netfinity 3000 server.
For information about termination requirements, see
“Termination requirements” on page 105.
External SCSI connector: You can attach external
SCSI devices to the 16-bit, 68-pin external SCSI connector
that is located on the rear of the server.
156
Netfinity Server HMM
Table 9 shows the pin-number assignments for the 68-pin
SCSI connectors.
Pin
Signal
Pin
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Terminal power
Terminal power
Reserved
Ground
Ground
Ground
Ground
Ground
Not connected
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Data 12
Data 13
Data 14
Data 15
Data P1
Data 0
Data 1
Data 2
Data 3
Data 4
Data 5
Data 6
Data 7
Data P0
Reserved
-PRSN
Terminal power
Terminal power
Reserved
Ground
-Attention
Ground
-Busy
-Acknowledge
-Reset
-Message
-Select
-Control/Data
-Request
-Input/Output
Data 8
Data 9
Data 10
Data 11
Table 9. The 68-Pin SCSI Port Connector Pin-Number
Assignments
IBM Netfinity 3000 - Type 8476
157
Universal serial bus ports:
The universal serial
bus (USB) is an emerging serial interface standard for
telephony and multimedia devices. Each USB port is a
single connector for devices that previously used serial,
parallel, keyboard, mouse, and game ports. USB
technology uses Plug and Play to determine which type of
device has been attached to the connector. Each USB
device is accessed by a unique USB address. A device
called a hub is used to convert a single USB connector
into multiple attachment points. A hub has multiple ports
where peripherals can be attached. USB provides 12
megabits-per-second (Mbps) bandwidth with a maximum of
63 peripherals and a maximum signal distance of five
meters per segment.
Note
If more than one USB device is to be attached, the
device must be connected to a hub. The Netfinity
3000 server does not support a keyboard attached to
the system USB port.
The Netfinity 3000 server comes with two USB ports.
Table 10 shows the pin-number assignments for the USB
port connectors.
Pin
Signal
1
2
3
4
VCC
−Data
+Data
Ground
Table 10. USB Port Connector Pin-Number Assignments
158
Netfinity Server HMM
Ethernet connector: The system board in the
Netfinity 3000 server contains an Ethernet controller. The
controller has an external RJ-45 connector on the rear of
the server that is used with a Category 5 twisted-pair
cable. Through this connector, you can attach an Ethernet
network cable to the internal transceiver in the server.
Attention:
The 10BASE-T Ethernet and the 100BASE-TX Fast
Ethernet cabling in the network must be Category 5 or
higher to meet various standards, including
electromagnetic compatibility.
See “Configuring the Ethernet controller” on page 38 for
additional information about the Ethernet controller.
Table 11 shows the pin-number assignments for the RJ-45
connector. These assignments apply to both 10BASE-T
and 100BASE-TX devices.
10BASE-T or 100 BASE-TX
UTP Cable
1
2
Pins
RJ-45 Modular Plug Connector
3
6
Pin
Signal
Pin
Signal
1
2
3
4
Transmit data+
Transmit data−
Receive data+
Reserved
5
6
7
8
Reserved
Receive data−
Reserved
Reserved
Table 11. Ethernet Connector Pin-Number Assignments
IBM Netfinity 3000 - Type 8476
159
Symptom-to-FRU index
This index supports the Netfinity 3000 - Type 8476.
Notes
1. Check the configuration before you replace a
FRU. Configuration problems can cause false
errors and symptoms.
2. For IBM devices not supported by index, refer to
the manual for that device.
3. Always start with “General Checkout” on page 4.
The Symptom-to-FRU Index lists beeps, errors, symptoms,
and the possible causes. The most likely cause is listed
first. Use this Symptom-to-FRU Index to help you decide
which FRUs to have available when servicing the
computer.
XX used in place of the last 2 digits can be any number or
letter.
No beep symptoms
No Beep/Symptom
No Beeps occur after
successfully completing
POST
(The Power-On Status is
disabled.)
FRU/Action
1. Run
Configuration/Setup,
set the Start Options
Power-On Status to
enable.
2. Check speaker
connection.
3. Speaker
4. System Board
Beep symptoms
Beep symptoms are short tones or a series of short tones
separated by pauses (intervals without sound). See the
following examples.
Beeps
1-2-X
Description
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
One beep
A pause (or break)
Two beeps
A pause (or break)
Any number of beeps
4
Four beeps
Beep/Symptom
FRU/Action
1-1-3
CMOS read/write error
1. Run Setup
2. System Board
1-1-4
ROM BIOS check error
1. System Board
160
Netfinity Server HMM
Beep/Symptom
FRU/Action
1-2-X
DMA error
1. System Board
1-3-X
1. Memory Module
2. System Board
1-3-4
1. Memory Types Mixed
- unbuffered &
registered
2-1-1, 2-1-2
1. Run Setup
2. System Board
2-1-X
First 64 KB of RAM failed.
1. Memory Module
2. System Board
2-2-2
1. Video Adapter
(if installed)
2. System Board
2-2-X
First 64 KB of RAM failed.
1. Memory Module
2. System Board
2-3-X
1. Memory Module
2. System Board
3-1-X
DMA register failed.
1. System Board
3-2-4
Keyboard controller failed.
1. System Board
2. Keyboard
One Beep
(POST completed
successfully or an incorrect
password was entered)
1. N/A
Two Short Beeps
(POST encountered an
error)
1. Run Diagnostics
Three Short Beeps
1. Dual Inline Memory
Module
2. Microprocessor
3. System Board
One Continuous Beep
1. Optional
Microprocessor
(if installed)
2. Microprocessor
3. Microprocessor
4. System Board
Repeating Short Beeps
1. Keyboard
2. System Board
One Long and One Short
Beep
1. Video adapter
(if present)
2. System Board
One Long and Two Short
Beeps
1. Video adapter
(if present)
2. System Board
IBM Netfinity 3000 - Type 8476
161
Beep/Symptom
FRU/Action
One Long and Three Short
Beeps
(Monitor not connected)
1. Verify monitor
connections
2. Video adapter
(if present)
3. System Board
Two Long and Two Short
Beeps
(Video adapter not
supported)
1. Video adapter
162
Netfinity Server HMM
POST error codes
POST Error
Code/Symptom
FRU/Action
101
System board interrupt
failure.
1. System Board
102
System board timer error.
1. System Board
106
1. System Board
110
System board memory
parity error.
1. Memory Module
2. System Board
111
I/O channel parity error.
1. Reseat adapters
2. Any Adapter
3. System Board
114
Adapter ROM error.
1. Adapter Memory
2. System Board
151
Real-time clock failure.
1. System Board
161
Bad CMOS battery.
1. Run Setup
2. CMOS Backup Battery
(See page 215.)
3. System Board
162
Configuration mismatch.
1. Run Setup and verify
Configuration
2. Had a device been
added, removed,
changed location? If
not, suspect that
device.
3. Power-on external
devices first, then
power-on computer.
4. CMOS Backup Battery
(See page 215.)
5. System Board
163
Clock not updating or invalid
time set.
1. Time and Date Set?
2. CMOS Backup Battery
(See page 215.)
3. System Board
164
POST detected a base
memory or extended
memory size mismatch
error.
1. Run Setup. Check
System Summary
menu for memory
size change.
2. Run the Extended
Memory Diagnostic
tests.
167
Microprocessor installed
that is not supported
by the current POST/BIOS.
1. Update the Flash
BIOS to the latest
level
2. Processor
IBM Netfinity 3000 - Type 8476
163
POST Error
Code/Symptom
FRU/Action
168
Alert on LAN error
1. Run Setup. Check to
see that Ethernet and
Alert on LAN are
enabled.
2. System Board
3. Riser Card, if installed.
175
1. Run Configuration
2. System Board
176
1. Covers were removed
from the computer.
177
Corrupted Administrator
Password.
1. System Board
17X not listed above
1. C2 Security
183
1. Enter the
administrator
password
184
RFID Antenna Installed
1. Make sure Asset
Care and Asset ID
are disabled in
Configuration/Setup.
An RFID Antenna
should not be installed.
186
1. System Board
187
1. Clear Administration
password
2. System Board
18X not listed above
1. C2 Security
190
Chassis intrusion detector
was cleared.
This is information only, no
action required.
If this code does not clear:
1. System Board
2. Riser Card, if installed
20X
Memory data error.
1. Run Enhanced Diag.
Memory Test
2. Memory Module
3. System Board
301
1. Keyboard
2. Keyboard Cable
3. System Board
303
With an 8603 error.
1.
2.
3.
4.
303
With no 8603 error.
1. Keyboard
2. Keyboard Cable
3. System Board
164
Netfinity Server HMM
Mouse
Keyboard
Keyboard Cable
System Board
POST Error
Code/Symptom
FRU/Action
601
1.
2.
3.
4.
602
1. Bad Diskette
2. Verify Diskette and
retry.
604
1. Run Setup and verify
diskette configuration
settings
2. Diskette Drive A/B
3. Diskette Drive Cable
4. Riser Card if drive
cable connected
5. System Board
662
1. Diskette drive
configuration error or
wrong diskette drive
type, run Setup
Configuration.
762
Math coprocessor
configuration error.
1. Run Setup
2. Processor
3. System Board
1762
Hard disk drive configuration
error.
1. Run Configuration
1780
1781
1782
1783
0)
1)
2)
3)
1. See “Power supply”
on page 45.
2. Hard Disk Drive
3. Riser Card, if hard disk
cable connected
4. System Board
5. Hard Disk Cable
6. Power Supply
180X, 188X
PCI configuration or
resource error.
1. Run Setup and verify
PCI/ISA configuration
settings.
2. If necessary, set ISA
adapters to “Not
available” to allow PCI
adapters to properly
configure.
3. Remove any suspect
ISA adapters.
4. Rerun diagnostics.
5. PCI Adapter
6. PCI Riser Card
(Disk
(Disk
(Disk
(Disk
Drive
Drive
Drive
Drive
Diskette Drive A
Diskette Drive Cable
Riser Card, if installed
System Board
IBM Netfinity 3000 - Type 8476
165
POST Error
Code/Symptom
FRU/Action
1962
Boot sequence error.
1. Run
Configuration/Setup,
check Boot Sequence
2. Check cable
connections
3. Run Diagnostics
4. Hard Disk Drive
5. System Board
2462
Video memory configuration
error.
1. Check cable
connections.
2. Run Setup and verify
video configuration
settings.
3. Video Memory
Modules
4. Video Adapter
(if installed)
5. System Board
5962
An IDE device (other than
hard drive) configuration
error.
1.
2.
3.
4.
8601, 8602
1. Pointing Device
(Mouse)
2. System Board
8603, 8604
1. System Board
2. Pointing Device
(Mouse)
86XX
Not listed above
1. Mouse
2. System Board
Run Configuration
CD-ROM Drive
CD-ROM Adapter
ZIP or other ATAPI
device
5. System Board
I999030X
Hard disk reset failure.
Possible hard disk drive
problem
Error not listed above
Follow the instructions on
the screen
166
Netfinity Server HMM
Diagnostic error codes
Refer to the following Diagnostic Error Codes when using
the IBM PC Enhanced Diagnostics test.
In the following index, “X” can represent any number.
Diagnostic Error Code
FRU/Action
000-000-XXX
BIOS Test Passed
1. No action
000-002-XXX
BIOS Timeout
1. Flash the system
2. System board
000-024-XXX
BIOS Addressing test failure
1. Flash the system
2. System board
000-025-XXX
BIOS Checksum Value error
1. Flash the system
2. Boot block
3. System board
000-026-XXX
FLASH data error
1. Flash the system
2. Boot block
3. System board
000-027-XXX
BIOS Configuration/Setup
error
1.
2.
3.
4.
Run Setup
Flash the system
Boot block
System board
000-034-XXX
BIOS Buffer Allocation
failure
1.
2.
3.
4.
Reboot the system
Flash the system
Run memory test
System board
000-035-XXX
BIOS Reset Condition
detected
1. Flash the system
2. System board
000-036-XXX
BIOS Register error
1. Flash the system
2. Boot block
3. System board
000-038-XXX
BIOS Extension failure
1. Flash the system
2. Adapter card
3. System board
000-039-XXX
BIOS DMI data error
1. Flash the system
2. System board
000-195-XXX
BIOS Test aborted by user
1. Information
2. Re-start the test, if
need to
000-196-XXX
BIOS test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
IBM Netfinity 3000 - Type 8476
167
Diagnostic Error Code
FRU/Action
000-197-XXX
BIOS test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
000-198-XXX
BIOS test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
000-199-XXX
BIOS test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
000-250-XXX
BIOS APM failure
1. Flash the system
2. System board
000-270-XXX
BIOS ACPI failure
1. Flash the system
2. System board
001-000-XXX
System Test Passed
1. No action
001-00X-XXX
System Error
1. System board
001-01X-XXX
System Error
1. System board
001-024-XXX
System Addressing test
failure
1. System board
001-025-XXX
System Checksum Value
error
1. Flash the system
2. System board
001-026-XXX
System FLASH data error
1. Flash the system
2. System board
001-027-XXX
System Configuration/Setup
error
1. Run Setup
2. Flash the system
3. System board
001-032-XXX
System Device Controller
failure
1. System board
001-034-XXX
System Device Buffer
Allocation failure
1.
2.
3.
4.
168
Netfinity Server HMM
Reboot the system
Flash the system
Run memory test
System board
Diagnostic Error Code
FRU/Action
001-035-XXX
System Device Reset
condition detected
1. System board
001-036-XXX
System Register error
1. System board
001-038-XXX
System Extension failure
1. Adapter card
2. System board
001-039-XXX
System DMI data structure
error
1. Flash the system
2. System board
001-040-XXX
System IRQ failure
1. Power-off/on system
and re-test
2. System board
001-041-XXX
System DMA failure
1. Power-off/on system
and re-test
2. System board
001-195-XXX
System Test aborted by
user
1. Information
2. Re-start the test, if
need to
001-196-XXX
System test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
001-197-XXX
System test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
001-198-XXX
System test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
001-199-XXX
System test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
001-250-XXX
System ECC error
1. System board
IBM Netfinity 3000 - Type 8476
169
Diagnostic Error Code
FRU/Action
001-254-XXX
001-255-XXX
001-256-XXX
001-257-XXX
System DMA error
1. System board
001-260-XXX
001-264-XXX
System IRQ error
1. System board
001-268-XXX
System IRQ1 failure
1. Device on IRQ1
2. System board
001-269-XXX
System IRQ2 failure
1. Device on IRQ2
2. System board
001-270-XXX
System IRQ3 failure
1. Device on IRQ3
2. System board
001-271-XXX
System IRQ4 failure
1. Device on IRQ4
2. System board
001-272-XXX
System IRQ5 failure
1. Device on IRQ5
2. System board
001-273-XXX
System IRQ6 (diskette
drive) failure
1. Diskette Cable
2. Diskette drive
3. System board
001-274-XXX
System IRQ7 failure
1. Device on IRQ7
2. System board
001-275-XXX
System IRQ8 failure
1. Device on IRQ8
2. System board
001-276-XXX
System IRQ9 failure
1. Device on IRQ9
2. System board
001-277-XXX
System IRQ10 failure
1. Device on IRQ10
2. System board
001-278-XXX
System IRQ11 failure
1. Device on IRQ11
2. System board
001-279-XXX
System IRQ12 failure
1. Device on IRQ12
2. System board
001-280-XXX
System IRQ13 failure
1. Device on IRQ13
2. System board
001-281-XXX
System IRQ14 (hard disk
drive) failure
1. Hard disk drive Cable
2. Hard disk drive
3. System board
001-282-XXX
System IRQ15 failure
1. Device on IRQ15
2. System board
001-286-XXX
001-287-XXX
001-288-XXX
System Timer failure
1. System board
001-292-XXX
System CMOS RAM error
1. Run Setup and
re-test
2. System board
001-293-XXX
System CMOS Battery
1. Battery
2. System board
170
Netfinity Server HMM
Diagnostic Error Code
FRU/Action
001-298-XXX
System RTC date/time
update failure
1. Flash the system
2. System board
001-299-XXX
System RTC periodic
interrupt failure
1. System board
001-300-XXX
System RTC Alarm failure
1. System board
001-301-XXX
System RTC Century byte
error
1. Flash the system
2. System board
005-000-XXX
Video Test Passed
1. No action
005-00X-XXX
Video error
1. Video card, if
installed
2. System board
005-010-XXX
005-011-XXX
005-012-XXX
005-013-XXX
Video Signal failure
1. Video card, if
installed
2. System board
005-016-XXX
Video Simple Pattern test
failure
1. Video Ram
2. Video card, if installed
3. System board
005-024-XXX
Video Addressing test
failure
1. Video card, if
installed
2. System board
005-025-XXX
Video Checksum Value
error
1. Video card, if
installed
2. System board
005-027-XXX
Video Configuration/Setup
error
1.
2.
3.
4.
Run Setup
Video drivers update
Video card, if installed
System board
005-031-XXX
Video Device Cable failure
1.
2.
3.
4.
Video cable
Monitor
Video card, if installed
System board
005-032-XXX
Video Device Controller
failure
1. Video card, if
installed
2. System board
005-036-XXX
Video Register error
1. Video card, if
installed
2. System board
005-038-XXX
System BIOS extension
failure
1. Video card, if
installed
2. System board
005-040-XXX
Video IRQ failure
1. Video card, if
installed
2. System board
IBM Netfinity 3000 - Type 8476
171
Diagnostic Error Code
FRU/Action
005-195-XXX
Video Test aborted by user
1. Information
2. Re-start the test, if
need to
005-196-XXX
Video test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
005-197-XXX
Video test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
005-198-XXX
Video test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
005-199-XXX
Video test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
005-2XX-XXX
005-3XX-XXX
Video subsystem error
1. Video card, if
installed
2. System board
006-000-XXX
Diskette interface Test
Passed
1. No action
006-0XX-XXX
Diskette interface error
1. Diskette drive Cable
2. Diskette drive
3. System board
006-195-XXX
Diskette interface Test
aborted by user
1. Information
2. Re-start the test, if
need to
006-196-XXX
Diskette interface test halt,
error threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
172
Netfinity Server HMM
Diagnostic Error Code
FRU/Action
006-197-XXX
Diskette interface test
warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
006-198-XXX
Diskette interface test
aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
006-199-XXX
Diskette interface test failed,
cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
006-25X-XXX
Diskette interface Error
1. Diskette drive Cable
2. Diskette drive
3. System board
011-000-XXX
Serial port Interface Test
Passed
1. No action
011-001-XXX
Serial port Presence
1. Remove external
serial device, if
present
2. Run setup, enable port
3. System board
011-002-XXX
011-003-XXX
Serial port Timeout/Parity
error
1. System board
011-013-XXX
011-014-XXX
Serial port Control
Signal/Loopback test failure
1. System board
011-015-XXX
Serial port External
Loopback failure
1. Wrap plug
2. System board
011-027-XXX
Serial port
Configuration/Setup error
1. Run Setup, enable
port
2. Flash the system
3. System board
011-03X-XXX
011-04X-XXX
Serial port failure
1. System board
IBM Netfinity 3000 - Type 8476
173
Diagnostic Error Code
FRU/Action
011-195-XXX
Serial port Test aborted by
user
1. Information
2. Re-start the test, if
need to
011-196-XXX
Serial port test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
011-197-XXX
Serial port test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
011-198-XXX
Serial port test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
011-199-XXX
Serial port test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
011-2XX-XXX
Serial port signal failure
1. External serial device
2. System board
014-000-XXX
Parallel port Interface Test
Passed
1. No action
014-001-XXX
Parallel port Presence
1. Remove external
parallel device, if
present
2. Run setup, enable port
3. System board
014-002-XXX
014-003-XXX
Parallel port Timeout/Parity
error
1. System board
014-013-XXX
014-014-XXX
Parallel port Control
Signal/Loopback test failure
1. System board
174
Netfinity Server HMM
Diagnostic Error Code
FRU/Action
014-015-XXX
Parallel port External
Loopback failure
1. Wrap plug
2. System board
014-027-XXX
Parallel port
Configuration/Setup error
1. Run Setup, enable
port
2. Flash the system
3. System board
014-03X-XXX
014-04X-XXX
Parallel port failure
1. System board
014-195-XXX
Parallel port Test aborted by
user
1. Information
2. Re-start the test, if
need to
014-196-XXX
Parallel port test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
014-197-XXX
Parallel port test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
014-198-XXX
Parallel port test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
014-199-XXX
Parallel port test failed,
cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
014-2XX-XXX
014-3XX-XXX
Parallel port failure
1. External parallel
device
2. System board
015-000-XXX
USB port Interface Test
Passed
1. No action
015-001-XXX
USB port Presence
1. Remove USB
Device(s) and re-test
2. System board
IBM Netfinity 3000 - Type 8476
175
Diagnostic Error Code
FRU/Action
015-002-XXX
USB port Timeout
1. Remove USB
Device(s) and re-test
2. System board
015-015-XXX
USB port External Loopback
failure
1. Remove USB
Device(s) and re-test
2. System board
015-027-XXX
USB port
Configuration/Setup error
1. Flash the system
2. System board
015-032-XXX
USB port Device Controller
failure
1. System board
015-034-XXX
USB port buffer allocation
failure
1.
2.
3.
4.
015-035-XXX
USB port Reset condition
detected
1. Remove USB
Device(s) and re-test
2. System board
015-036-XXX
USB port Register error
1. System board
015-040-XXX
USB port IRQ failure
1. Run setup and check
for conflicts
2. Flash the system
3. System board
015-195-XXX
USB port Test aborted by
user
1. Information
2. Re-start the test, if
need to
015-196-XXX
USB port test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
015-197-XXX
USB port test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
015-198-XXX
USB port test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
176
Netfinity Server HMM
Reboot the system
Flash the system
Run memory test
System board
Diagnostic Error Code
FRU/Action
015-199-XXX
USB port test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
018-000-XXX
PCI Card Test Passed
1. No action
018-0XX-XXX
PCI Card Failure
1. PCI card
2. Riser card, if installed
3. System board
018-195-XXX
PCI Card Test aborted by
user
1. Information
2. Re-start the test, if
need to
018-196-XXX
PCI Card test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
018-197-XXX
PCI Card test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
018-198-XXX
PCI Card test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
018-199-XXX
PCI Card test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
018-250-XXX
PCI Card Services error
1. PCI card
2. Riser card, if installed
3. System board
020-000-XXX
PCI Interface Test Passed
1. No action
020-0XX-XXX
PCI Interface error
1. PCI card
2. Riser card, if installed
3. System board
IBM Netfinity 3000 - Type 8476
177
Diagnostic Error Code
FRU/Action
020-195-XXX
PCI Test aborted by user
1. Information
2. Re-start the test, if
need to
020-196-XXX
PCI test halt, error threshold
exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
020-197-XXX
PCI test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
020-198-XXX
PCI test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
020-199-XXX
PCI test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
020-262-XXX
PCI system error
1. PCI card
2. Riser card, if installed
3. System board
025-000-XXX
IDE interface Test Passed
1. No action
025-00X-XXX
025-01X-XXX
IDE interface failure
1.
2.
3.
4.
IDE signal cable
Check power supply
IDE device
System board
025-027-XXX
IDE interface
Configuration/Setup error
1.
2.
3.
4.
IDE signal cable
Flash the system
IDE device
System board
025-02X-XXX
025-03X-XXX
025-04X-XXX
IDE Interface failure
1.
2.
3.
4.
IDE signal cable
Check power supply
IDE device
System board
025-195-XXX
IDE interface Test aborted
by user
1. Information
2. Re-start the test, if
need to
178
Netfinity Server HMM
Diagnostic Error Code
FRU/Action
025-196-XXX
IDE interface test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
025-197-XXX
IDE interface test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
025-198-XXX
IDE interface test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
025-199-XXX
IDE interface test failed,
cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
030-000-XXX
SCSI interface Test Passed
1. No action
030-00X-XXX
030-01X-XXX
SCSI interface failure
1.
2.
3.
4.
030-027-XXX
SCSI interface
Configuration/Setup error
1.
2.
3.
4.
030-03X-XXX
030-04X-XXX
SCSI interface error
1.
2.
3.
4.
030-195-XXX
SCSI interface Test aborted
by user
1. Information
2. Re-start the test, if
need to
SCSI signal cable
Check power supply
SCSI device
SCSI adapter card, if
installed
5. System board
SCSI signal cable
Flash the system
SCSI device
SCSI adapter card, if
installed
5. System board
SCSI signal cable
Check power supply
SCSI device
SCSI adapter card, if
installed
5. System board
IBM Netfinity 3000 - Type 8476
179
Diagnostic Error Code
FRU/Action
030-196-XXX
SCSI interface test halt,
error threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
030-197-XXX
SCSI interface test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
030-198-XXX
SCSI interface test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
030-199-XXX
SCSI interface test failed,
cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
035-000-XXX
RAID interface Test Passed
1. No action
035-0XX-XXX
RAID interface Failure
1. RAID signal cable
2. RAID device
3. RAID adapter card, if
installed
4. System board
035-195-XXX
RAID interface Test aborted
by user
1. Information
2. Re-start the test, if
need to
035-196-XXX
RAID interface test halt,
error threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
180
Netfinity Server HMM
Diagnostic Error Code
FRU/Action
035-197-XXX
RAID interface test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
035-198-XXX
RAID interface test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
035-199-XXX
RAID interface test failed,
cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
071-000-XXX
Audio port Interface Test
Passed
1. No action
071-00X-XXX
071-01X-XXX
071-02X-XXX
Audio port error
1. Run Setup
2. Flash the system
3. System board
071-03X-XXX
Audio port failure
1.
2.
3.
4.
071-04X-XXX
Audio port failure
1. Run Setup
2. Audio card, if installed
3. System board
071-195-XXX
Audio port Test aborted by
user
1. Information
2. Re-start the test, if
need to
071-196-XXX
Audio port test halt, error
threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
Speakers
Microphone
Audio card, if installed
System board
IBM Netfinity 3000 - Type 8476
181
Diagnostic Error Code
FRU/Action
071-197-XXX
Audio port test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
071-198-XXX
Audio port test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
071-199-XXX
Audio port test failed, cause
unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
071-25X-XXX
Audio port failure
1. Speakers
2. Audio card, if installed
3. System board
080-000-XXX
Game Port interface Test
Passed
1. No action
080-XXX-XXX
Game Port interface Error
1. Remove the game
port device and
re-test the system
080-195-XXX
Game Port interface Test
aborted by user
1. Information
2. Re-start the test, if
need to
080-196-XXX
Game Port interface test
halt, error threshold
exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
080-197-XXX
Game Port interface test
warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
182
Netfinity Server HMM
Diagnostic Error Code
FRU/Action
080-198-XXX
Game Port interface test
aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
080-199-XXX
Game Port interface test
failed, cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
086-000-XXX
Mouse Port interface Test
Passed
1. No action
086-001-XXX
Mouse Port interface
Presence
1. Mouse
2. System board
086-032-XXX
Mouse Port interface Device
controller failure
1. Mouse
2. System board
086-035-XXX
Mouse Port interface Reset
1. Mouse
2. System board
086-040-XXX
Mouse Port interface IRQ
failure
1. Run Setup
2. Mouse
3. System board
086-195-XXX
Mouse Port interface Test
aborted by user
1. Information
2. Re-start the test, if
need to
086-196-XXX
Mouse Port interface test
halt, error threshold
exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
086-197-XXX
Mouse Port interface test
warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
IBM Netfinity 3000 - Type 8476
183
Diagnostic Error Code
FRU/Action
086-198-XXX
Mouse Port interface test
aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
086-199-XXX
Mouse Port interface test
failed, cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
089-000-XXX
Microprocessor Test Passed
1. No action
089-XXX-XXX
Microprocessor failure
1. Microprocessor(s)
2. System board
089-195-XXX
Microprocessor Test aborted
by user
1. Information
2. Re-start the test, if
need to
089-196-XXX
Microprocessor test halt,
error threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
089-197-XXX
Microprocessor test warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
089-198-XXX
Microprocessor test aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
089-199-XXX
Microprocessor test failed,
cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
184
Netfinity Server HMM
Diagnostic Error Code
FRU/Action
170-000-XXX
Voltage Sensor(s) Test
Passed
1. No action
170-0XX-XXX
Voltage Sensor(s) failure
1. Flash system
2. System board
170-195-XXX
Voltage Sensor(s) Test
aborted by user
1. Information
2. Re-start the test, if
need to
170-196-XXX
Voltage Sensor(s) test halt,
error threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
170-197-XXX
Voltage Sensor(s) test
warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
170-198-XXX
Voltage Sensor(s) test
aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
170-199-XXX
Voltage Sensor(s) test
failed, cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
170-250-XXX
170-251-XXX
Voltage Sensor(s) Voltage
limit error
1. Power supply
2. System board
170-254-XXX
Voltage Sensor(s) Voltage
Regulator Module error
1. Voltage Regulator
Module (VRM)
2. Microprocessor
3. System board
175-000-XXX
Thermal Sensor(s) Test
Passed
1. No action
175-0XX-XXX
Thermal Sensor(s) failure
1. Flash system
2. System board
IBM Netfinity 3000 - Type 8476
185
Diagnostic Error Code
FRU/Action
175-195-XXX
Thermal Sensor(s) Test
aborted by user
1. Information
2. Re-start the test, if
need to
175-196-XXX
Thermal Sensor(s) test halt,
error threshold exceeded
1. Press F3 to review
the log file. See
“Viewing the test
log” on page 14.
2. Re-start the test to
reset the log file.
175-197-XXX
Thermal Sensor(s) test
warning
1. Make sure
component that is
called out is enabled
and/or connected
2. Re-run test
3. Component that is
called out in warning
statement
4. Component under test
175-198-XXX
Thermal Sensor(s) test
aborted
1. If a component is
called out, make sure
it is enabled and/or
connected
2. Flash the system and
re-test
3. Go to “Undetermined
problems” on
page 198
175-199-XXX
Thermal Sensor(s) test
failed, cause unknown
1. Go to “Undetermined
problems” on
page 198.
2. Flash the system and
re-test
3. Replace component
under function test.
175-250-XXX
175-251-XXX
Thermal Sensor(s) limit
error
1.
2.
3.
4.
185-000-XXX
Asset Security Test Passed
1. No action
185-XXX-XXX
Asset Security failure
1. Assure Asset
Security Enabled
2. Flash system
3. System board
185-278-XXX
Asset Security Chassis
Intrusion
1. C2 Cover Switch
2. System board
201-000-XXX
System Memory Test
Passed
1. No action
201-XXX-XXX
System Memory error
1. Replace the memory
module called out by
the test
2. System board
186
Netfinity Server HMM
Check fans
Check Power supply
Microprocessor
System board
Diagnostic Error Code
FRU/Action
202-000-XXX
System Cache Test Passed
1. No action
202-XXX-XXX
System Cache error
1. Cache, if removable
2. System board
3. Microprocessor
206-000-XXX
Diskette Drive Test Passed
1. No action
206-XXX-XXX
Diskette Drive error
1. Diskette Drive Cable
2. Check power supply
voltages
3. Diskette drive
4. System board
215-000-XXX
CD-ROM Drive Test Passed
1. No action
215-XXX-XXX
CD-ROM Drive error
1. CD-ROM Drive Cable
2. Check power supply
voltages
3. CD-ROM drive
4. System board
217-000-XXX
Hard Disk Drive Test
Passed
1. No action
217-25X-XXX
217-26X-XXX
Hard Disk Drive (IDE) error
1. Hard Disk Drive
Cable
2. Check power supply
voltages
3. Hard Disk drive (IDE)
4. System board
217-28X-XXX
217-29X-XXX
Hard Disk Drive (SCSI)
error
1. Hard Disk Drive
Cable
2. Check power supply
voltages
3. Hard Disk drive (SCSI)
4. SCSI adapter card
5. System board
220-000-XXX
Hi-Capacity Cartridge Drive
Test Passed
1. No action
220-XXX-XXX
Hi-Capacity Cartridge Drive
error
1. Remove the
Hi-Capacity Cartridge
Drive and re-test the
system
301-000-XXX
Keyboard Test Passed
1. No action
301-XXX-XXX
Keyboard error
1. Keyboard
2. Check and test Mouse
3. System board
302-000-XXX
Mouse Test Passed
1. No action
IBM Netfinity 3000 - Type 8476
187
Diagnostic Error Code
FRU/Action
302-XXX-XXX
Mouse error
1. Mouse
2. Check and test
Keyboard
3. System board
303-000-XXX
Joystick Test Passed
1. No action
303-XXX-XXX
Joystick error
1. Remove the Joystick
and re-test the
system
305-000-XXX
Monitor DDC Test Passed
1. No action
305-250-XXX
Monitor DDC self-test failure
1. Run Setup to enable
DDC
2. Cable
3. Monitor
4. Video card
5. System board
415-000-XXX
Modem Test Passed
1. No action
415-XXX-XXX
Modem error
1. Remove the Modem
and re-test the
system
188
Netfinity Server HMM
Ethernet controller messages
Note
The following error messages are available only with
the integrated Ethernet controller. These error
messages are not available when remote program
load (RPL) or dynamic host configuration protocol
(DHCP) is used through optional network adapters.
If a failure condition occurs after the Ethernet controller is
initialized, one or more of the following error messages will
be displayed on the screen.
The two most common error messages are:
RPL-ROM-ERR:
1ð5
RPL-ROM-ERR:
1ð7
The integrated Ethernet
failed the loopback test.
The media test failed.
Error 105 indicates that a power-on diagnostic test
performed by the Ethernet module did not execute
correctly. If this error message appears, replace the
system board. Error 107 indicates that the cable from the
LAN is not securely connected to the Ethernet port on the
server. Check the cable to ensure that it is properly
connected.
Other error messages that might occur are shown in
Table 12 on page 190.
Note
An x value that follows an error code represents any
alphanumeric character.
IBM Netfinity 3000 - Type 8476
189
Table 12 (Page 1 of 2). Ethernet Controller Messages
Error Code
Description
RPL-ROM-ERR: 100
The integrated Ethernet controller cannot be
found.
Action: Make sure that the Ethernet controller
is enabled in the BIOS. If the problem persists,
replace the system board.
RPL-ROM-ERR: 101
The integrated Ethernet controller was unable to
initialize.
Action: Make sure that the Ethernet controller
is enabled in the BIOS. If the problem persists,
replace the system board.
RPL-ROM-ERR: 102
The integrated Ethernet controller could not be
reset.
Action: Make sure that the Ethernet controller
is enabled in the BIOS. If the problem persists,
replace the system board.
RPL-ROM-ERR: 103
There are multiple Ethernet controllers or
adapters in the system.
Action: Specify the correct serial number in the
NET.CFG file.
RPL-ROM-ERR: 104
RPL-ROM-ERR: 105
The integrated Ethernet controller EEPROM is
faulty or not present.
The integrated Ethernet failed the loopback test.
A power-on diagnostic test performed by the
Ethernet module did not execute correctly.
Action: Replace the system board.
RPL-ROM-ERR: 106
RPL-ROM-ERR: 107
The integrated Ethernet controller is configured
for Plug and Play in a non-Plug and Play system.
The media test failed.
Action: The cable from the LAN is not securely
connected to the Ethernet port on the server.
Check the cable to ensure that it is properly
connected.
RPL-ROM-ERR: 110
The integrated Ethernet controller RAM failed the
memory test.
Action: Replace the system board.
E61
Service boot (startup) canceled; that is, the boot
diskette image was not downloaded from the
network.
Action: No action is required.
E62
Cannot initialize controller.
E63
Cannot initialize controller.
E67
Cannot initialize controller.
E6d
Cannot find boot protocol (BOOTP) server.
E6e
Cannot start from downloaded image.
E71
Too many multicast trivial file transfer protocol
(MTFTP) packages.
M10
Address resolution protocol (ARP) canceled by
keystroke.
Action: No action is required.
M11
ARP timeout.
M20
Cannot copy memory.
M21
Cannot write to memory.
M22
Cannot write to memory.
190
Netfinity Server HMM
Table 12 (Page 2 of 2). Ethernet Controller Messages
Error Code
Description
M30
Cannot ARP trivial file transfer protocol (TFTP)
address.
M31
TFTP canceled by keystroke.
M32
TFTP open timeout.
M33
Unknown TFTP parameter (operation code).
M34
TFTP read canceled by keystroke.
M35
TFTP timeout.
M38
Cannot open TFTP connection.
M39
Cannot read from TFTP connection.
M40
BOOTP canceled by keystroke.
M40
DHCP canceled by keystroke.
M41
BOOTP timeout.
M41
DHCP timeout.
M42
No client or server Internet protocol (IP) address.
M43
No boot (startup) file name.
M44
Cannot ARP redirected BOOTP server.
M6f
System is locked. Press Ctrl+Alt+Del to restart.
M90
Cannot initialize controller for multicast address.
M91
MTFTP canceled by keystroke.
M92
MTFTP open timeout.
M93
Unknown MTFTP parameter (operation code).
M94
MTFTP read canceled by keystroke.
M95
MTFTP timeout.
M96
Cannot ARP MTFTP address.
M98
Cannot open MTFTP connection.
M99
Cannot read from MTFTP connection.
Txx
If you are running a TFTP session to another
computer, an error message generated by the
TFTP session will contain a message prefix of
Txx.
Miscellaneous symptoms
Symptom
FRU/Action
CD-ROM drive not working
properly.
1. Clean the CD
2. Clean the optical-head
lens
3. CD-ROM Drive
CD-ROM drive tray is not
working.
1. CD-ROM Drive
IBM Netfinity 3000 - Type 8476
191
Symptom
FRU/Action
Server does not recognize
the CD-ROM drive.
1. Verify that the
CD-ROM drive is
enabled in the
Configuration/Setup
Utility program.
2. Verify that the server is
checking for the
CD-ROM drive in the
startup sequence. Use
the
Configuration/Setup
Utility program.
3. CD
4. CD-ROM Drive
CD-ROM drive in-use light
stays on, or the system
continues to bypass the
CD-ROM drive.
1. CD-ROM
2. CD-ROM Cable
Diskette drive in-use light
stays on, or the system
bypasses the diskette drive.
1. Verify that the
diskette drive is
enabled in the
Configuration/Setup
Utility program.
2. Verify that a know
good diskette is
properly inserted in the
drive
3. The diskette contains
the necessary files to
start the system
4. Diskette Drive
General monitor problems.
Some IBM monitors have
their own self-tests. If you
suspect a problem with the
monitor, refer to the
information that comes with
the monitor for adjusting
and testing instructions.
1. Monitor
The screen is blank.
1. Check power cord
and cable
connections.
2. Monitor
3. Video Adapter
Only the cursor appears.
1. Video Adapter
The monitor goes blank
when some application
programs start.
1. Check all cable
connections.
2. Verify that the graphics
adapter is correctly
installed in slot 1, the
Accelerated Graphics
Port (AGP).
3. Verify that the device
drivers necessary for
the applications are
installed.
192
Netfinity Server HMM
Symptom
FRU/Action
The monitor works when
you power-on the system,
but goes blank after some
period of server inactivity.
Note
The Advanced Power
Management (APM)
feature is not
supported.
Screen flickers.
Attention
Using a resolution or
refresh rate that is not
supported by the
monitor might damage
it.
Wavy, unreadable, rolling,
distorted screen, or screen
jitter.
If the monitor self-tests
show that the monitor is
working properly, verify that:
1. If enabled, disable
the Advanced Power
Management (APM)
feature setting in the
Configuration/Setup
Utility program.
1. Set monitor to
highest,
noninterlaced refresh
rate supported by the
monitor and
controller.
2. Monitor
3. Video Adapter
1. Monitor
2. Video Adapter
1. Check the location of
the Monitor.
2. Verify that an IBM
monitor signal cable is
properly connected.
3. Verify that the monitor
is not trying to run at a
higher refresh rate than
supported.
Wrong characters appear on
the screen.
1. Video Adapter Cable
2. Video Adapter
The server does not start
when you press the power
switch.
Before replacing a FRU:
1. Power Switch/LED
Assembly
2. Power Supply
1. Check all cable
connections.
2. Verify that the the
server cover is properly
installed.
3. Verify that the power
outlet functions
properly.
4. Verify that the correct
type of memory is
installed.
IBM Netfinity 3000 - Type 8476
193
Symptom
An IBM option that used to
work does not work now.
Notes
1. If the option
comes with its
own test
instructions, use
those instructions
to test the option.
2. An external option
must be
powered-on prior
to powering-on
the system.
FRU/Action
1. Check all cable
connections.
2. For SCSI options,
check for proper
termination.
3. Option Device
The parallel port cannot be
accessed, or the number of
parallel ports displayed is
less than the number of
parallel ports installed.
1. Device
2. Adapter, if installed
3. System Board
The serial port cannot be
accessed, or the number of
serial ports displayed is less
than the number of serial
ports installed.
1. Device
2. Adapter, if installed
3. System Board
Serial port and USB port
problems.
1. Device
2. Adapter, if installed
3. System Board
The SCSI expansion
enclosure used to work, but
does not work now.
1. Verify that all SCSI
expansion enclosure
hardware and cable
connections are
secure.
2. Verify termination of
the last option in each
SCSI chain, or the end
of the SCSI cable.
3. If the SCSI expansion
enclosure comes with
its own test
instructions, use those
instructions to test it.
4. SCSI Repeater Card
The SCSI Repeater Card
used to work, but does not
work now.
1. Verify that all SCSI
Repeater Card
hardware and cable
connections are
secure.
2. Verify that all external
SCSI option cables are
connected correctly.
3. Verify the termination
of the last option in
each SCSI chain, or
the end of the SCSI
cable.
4. SCSI Repeater Card
194
Netfinity Server HMM
Symptom
FRU/Action
The Ethernet Controller
cannot connect to the
network.
1. Run Diagnostics
2. Check Cables
3. System Board
The Configuration/Setup
Utility program reports the
Ethernet controller interrupt
Utility as 0 or 255.
The PCI BIOS is not
configuring the Ethernet
controller or adapter
correctly.
1. The PCI BIOS
interrupt settings are
incorrect. Check for
interrupt conflicts
with ISA devices. If
conflicts are found,
reserve the ISA
interrupts (see “ISA
legacy resources” on
page 36) so that the
PCI BIOS will assign
another
non-conflicting PCI
interrupt value.
The Configuration/Setup
Utility program reports No
PCI Bus.
The Configuration/Setup
Utility program has been run
on another computer that
does not have any PCI
slots.
1. Run the
Configuration/Setup
Utility program on
the server so that the
PCI BIOS will
configure the
Ethernet controller or
adapter correctly
The server stops running
when loading device drivers.
The PCI BIOS interrupt
settings are incorrect.
1. Check for interrupt
conflicts with ISA
devices. If conflicts
are found, reserve
the ISA interrupts
(see “ISA legacy
resources” on
page 36) so that the
PCI BIOS will assign
another
non-conflicting PCI
interrupt value.
The diagnostics completed
successfully, but the
network connection fails.
1. Make sure that the
network cable is
securely attached.
2. Make sure that you are
using Category 5
cabling when operating
the server at either
10 Mbps or 100 Mbps.
IBM Netfinity 3000 - Type 8476
195
Symptom
FRU/Action
The Ethernet Activity light
does not come on.
1. Make sure the
network device
drivers are loaded.
2. Check all connections.
3. Try sending data from
this workstation.
4. Use another Ethernet
adapter (see “Installing
or removing ISA and
PCI adapters” on
page 62).
5. Use another port on
the hub.
6. Make sure that the hub
port is configured for
the correct speed (10
Mbps or 100 Mbps).
7. If duplex mode was
forced, make sure a
speed of 10 Mbps or
100 Mbps was forced.
8. If you manually
configured the duplex
mode, make sure that
you also manually
configured the speed.
9. System Board
Data is incorrect or
sporadic.
1. Make sure that you
are using Category 5
cabling when
operating the server
at either 10 Mbps or
100 Mbps.
The Ethernet controller or
adapter stopped working
when another adapter was
added to the server.
1. Make sure that the
cable is connected to
the Ethernet adapter.
2. Make sure that the PCI
system BIOS is
current.
3. Reseat the adapter.
4. System Board
The Ethernet controller or
adapter stopped working
without apparent cause.
1. Reseat the adapter.
2. Try a different
connector at the hub or
switch.
3. The network device
driver files might be
missing or corrupted;
4. System Board
196
Netfinity Server HMM
SCSI messages
Message
Description
All
One or more of the following
might be causing the
problem:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
1. Verify SCSI
Configuration
2. SCSI Device
3. SCSI Controller
A failing SCSI device
(adapter, drive,
controller)
An improper SCSI
configuration or SCSI
termination jumper
setting
Duplicate SCSI IDs in
the same SCSI chain
A missing or improperly
installed SCSI
terminator
A defective SCSI
terminator
An improperly installed
cable
A defective cable
IBM Netfinity 3000 - Type 8476
197
Undetermined problems
You are here because the diagnostic tests did not identify
the failure, the Devices List is incorrect, or the system is
inoperative.
Notes
If you suspect a software mismatch is causing failures
(solid or intermittent), be sure to see “Configuration
conflicts” on page 20.
Check power supply. If the LEDs indicate the power
supplies are working correctly, return here and do the
following:
1. Power-off the computer.
2. Remove or disconnect the following (one at a time)
until you find the failure (power-on the computer and
reconfigure each time).
Ÿ Any external devices
Ÿ Surge suppressor device (on the computer)
Ÿ Modem, printer, mouse, or non-IBM devices
Ÿ Each adapter
Ÿ Drives
Ÿ Memory-Module Kits (Minimum requirement = 1
bank of 64 MB DIMMs)
Note
Minimum operating requirements vary for each
computer. For example, an IML drive in the drive
startup sequence (IML systems only).
3. Power-on the computer. If the problem remains,
suspect the following FRUs in the order listed:
Ÿ System Board
Ÿ Processor Board
Ÿ Front Panel
Note
If the problem goes away when you remove an
adapter from the system, and replacing that adapter
does not correct the problem, suspect the system
board then the processor board(s).
198
Netfinity Server HMM
12
17
20
21
23
22
24
25
26
27
19 18
28
16
15
14
13
11
9
10
6
7
5
4
3
2
1
8
Parts listing (Netfinity 3000 - Type 8476)
IBM Netfinity 3000 - Type 8476
199
System
Index
1
2
3
4
5
5
5
6
6
6
7
200
System (Netfinity 3000 - Type 8476)
Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U
FRU
No.
Cover and Handle (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
Power Switch/LED Cable Assembly
(Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U)
Top Cover Assembly (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
Front Bezel (Bay Panel) (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
CD-ROM Drive (32X) (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X)
CD-ROM Drive (32X) (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X)
CD-ROM Drive (40X) (Models 60U,
61U, 70U, 71U)
CD-ROM Audio Cable (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
4.5 GB SCSI Hard Disk Drive (Models
11X, 21X)
9.1 GB SCSI Hard Disk Drive (Models
31U, 31X, 41U, 41X)
9.1 GB SCSI Hard Disk Drive (Models
51U, 51X, 61U)
1.44 MB Diskette Drive (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
02K2785
Netfinity Server HMM
12J4510
01K1637
12J5548
02K1119
02K3414
36L8757
75H9219
10L6084
10L6085
36L8648
75H9550
Index
8
9
10
11
12
13
14
14
15
15
15
15
15
System (Netfinity 3000 - Type 8476)
Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U
Diskette Drive Cable (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
Miscellaneous Blank Bezels (Bay
Panels) (Models 10U, 10X, 11U, 11X,
15U, 15X, 16U, 16X, 20U, 20X, 21U,
21X, 30U, 30X, 31U, 31X, 40U, 40X,
41U, 41X, 50U, 50X, 51U, 51X, 60U,
61U, 70U, 71U)
3.5-Inch Bezel (Bay Panel) Assembly
(Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U)
Model Name Plate (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
Bottom Cover Assembly (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
Foot (4 each) (Models 10U, 10X, 11U,
11X, 15U, 15X, 16U, 16X, 20U, 20X,
21U, 21X, 30U, 30X, 31U, 31X, 40U,
40X, 41U, 41X, 50U, 50X, 51U, 51X,
60U, 61U, 70U, 71U)
System Board Latch and Screw
(Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U)
32 MB ECC DIMM (Models 10U, 10X,
11U, 11X, 15U, 15X)
64 MB ECC DIMM (Models 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
266MHz/512 Cache Processor (Models
10U, 10X, 11U, 11X)
300MHz/512 Cache Processor (Models
15U, 15X, 16U, 16X)
350MHz/512 Cache Processor (Models
20U, 20X, 21U, 21X)
400MHz/512 Cache Processor (Models
30U, 30X, 31U, 31X)
450MHz/512 Cache Processor (Models
40U, 40X, 41U, 41X)
IBM Netfinity 3000 - Type 8476
FRU
No.
76H7340
01K1888
12J5549
03K9569
03K9587
12J4506
01K1612
01K1143
01K1140
01K2169
01K4291
01K4333
01K4334
01K1578
201
Index
15
15
15
16
16
16
17
18
19
20
21
22
23
202
System (Netfinity 3000 - Type 8476)
Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U
500MHz/512 Cache Processor (Models
50U, 50X, 51U, 51X)
550MHz/512 Cache Processor (Models
60U, 61U)
600MHz/512 Cache Processor (Models
70U, 71U)
System Board without Memory, CPU,
or Cache (Models 10U, 10X, 11U, 11X,
15U, 15X, 16U, 16X, 20U, 20X, 21U,
21X, 30U, 30X, 31U, 31X, 40U, 40X,
41U, 41X)
System Board without Memory, CPU,
or Cache (Models 50U, 50X, 51U, 51X)
System Board without Memory, CPU,
or Cache (Models 60U, 61U, 70U, 71U)
Fan Bracket (for 02K2861) (Models
10U, 10X, 11U, 11X, 15U, 15X, 16U,
16X, 20U, 20X, 21U, 21X, 30U, 30X,
31U, 31X, 40U, 40X, 41U, 41X, 50U,
50X, 51U, 51X, 60U, 61U, 70U, 71U)
92MM Fan Assembly (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
Card Guide (Models 10U, 10X, 11U,
11X, 15U, 15X, 16U, 16X, 20U, 20X,
21U, 21X, 30U, 30X, 31U, 31X, 40U,
40X, 41U, 41X, 50U, 50X, 51U, 51X,
60U, 61U, 70U, 71U)
EMC kit (Models 10U, 10X, 11U, 11X,
15U, 15X, 16U, 16X, 20U, 20X, 21U,
21X, 30U, 30X, 31U, 31X, 40U, 40X,
41U, 41X, 50U, 50X, 51U, 51X, 60U,
61U, 70U, 71U)
Access Cover Assembly (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
C2 Switch Cable Assembly (Models
10U, 10X, 11U, 11X, 15U, 15X, 16U,
16X, 20U, 20X, 21U, 21X, 30U, 30X,
31U, 31X, 40U, 40X, 41U, 41X, 50U,
50X, 51U, 51X, 60U, 61U, 70U, 71U)
AGP Cover (Models 10U, 10X, 11U,
11X, 15U, 15X, 16U, 16X, 20U, 20X,
21U, 21X, 30U, 30X, 31U, 31X, 40U,
40X, 41U, 41X, 50U, 50X, 51U, 51X,
60U, 61U, 70U, 71U)
Netfinity Server HMM
FRU
No.
33L1615
37L5603
01N2037
11L1619
61H2322
61H2464
03K9606
02K2861
03K9605
12J4508
12J5546
01K1495
03K9623
Index
24
25
26
27
28
System (Netfinity 3000 - Type 8476)
Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U
3.5-Inch Hard Disk Drive Bracket
(Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U)
I/O Clamp (Models 10U, 10X, 11U,
11X, 15U, 15X, 16U, 16X, 20U, 20X,
21U, 21X, 30U, 30X, 31U, 31X, 40U,
40X, 41U, 41X, 50U, 50X, 51U, 51X,
60U, 61U, 70U, 71U)
Power Supply 330 Watt (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
Keylock Assembly (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
Chassis Assembly (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
3.5/5.25-Inch DASD Bracket (Models
10U, 10X, 11U, 11X, 15U, 15X, 16U,
16X, 20U, 20X, 21U, 21X, 30U, 30X,
31U, 31X, 40U, 40X, 41U, 41X, 50U,
50X, 51U, 51X, 60U, 61U, 70U, 71U)
60MM Fan Assembly (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
92MM Fan and Bracket Kit (Models
10U, 10X, 11U, 11X, 15U, 15X, 16U,
16X, 20U, 20X, 21U, 21X, 30U, 30X,
31U, 31X, 40U, 40X, 41U, 41X, 50U,
50X, 51U, 51X, 60U, 61U, 70U, 71U)
IDE (2X) Drive Cable (Models 10U,
10X, 11U, 11X, 15U, 15X, 16U, 16X,
20U, 20X, 21U, 21X, 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
Keyboard
(See“Keyboards” on page 206 .)
(Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X)
IBM Netfinity 3000 - Type 8476
FRU
No.
03K9608
03K9604
01K9866
12J5102
03K9609
12J4501
10L5513
37L3062
12J4518
203
Index
204
System (Netfinity 3000 - Type 8476)
Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U
L-shaped bracket for specific PCI card
retention (Models 10U, 10X, 11U, 11X,
15U, 15X, 16U, 16X, 20U, 20X, 21U,
21X, 30U, 30X, 31U, 31X, 40U, 40X,
41U, 41X, 50U, 50X, 51U, 51X, 60U,
61U, 70U, 71U)
Miscellaneous Hardware Kit (Models
10U, 10X, 11U, 11X, 15U, 15X, 16U,
16X, 20U, 20X, 21U, 21X, 30U, 30X,
31U, 31X, 40U, 40X, 41U, 41X, 50U,
50X, 51U, 51X, 60U, 61U, 70U, 71U)
Miscellaneous Optional Bezel (Bay
Panel) (Models 10U, 10X, 11U, 11X,
15U, 15X, 16U, 16X, 20U, 20X, 21U,
21X, 30U, 30X, 31U, 31X, 40U, 40X,
41U, 41X, 50U, 50X, 51U, 51X, 60U,
61U, 70U, 71U)
Mouse (Models 10U, 10X, 11U, 11X,
15U, 15X, 16U, 16X, 20U, 20X, 21U,
21X, 30U, 30X, 31U, 31X, 40U, 40X,
41U, 41X, 50U, 50X, 51U, 51X, 60U,
61U, 70U, 71U)
Power Switch Cover (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
Riser Card (Models 10U, 10X, 11U,
11X, 15U, 15X, 16U, 16X, 20U, 21U,
20X, 21X)
Riser Card (Models 30U, 30X, 31U,
31X, 40U, 40X, 41U, 41X, 50U, 50X,
51U, 51X, 60U, 61U, 70U, 71U)
Riser Supports, Front and Rear
(Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U)
SCSI Card (Models 11U, 11X, 16U,
16X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
SCSI Cable (Models 10U, 10X, 11U,
11X, 15U, 15X, 16U, 16X, 20U, 20X,
21U, 21X, 30U, 30X, 31U, 31X, 40U,
40X, 41U, 41X, 50U, 50X, 51U, 51X,
60U, 61U, 70U, 71U)
SCSI LED Cable (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
Netfinity Server HMM
FRU
No.
00N7043
03K9603
12J5551
76H0889
03K9657
20L0926
61H2331
02K2766
10L7095
01K1467
76H7344
Index
System (Netfinity 3000 - Type 8476)
Models 10U, 10X, 11U, 11X, 15U,
15X, 16U, 16X, 20U, 20X, 21U, 21X,
30U, 30X, 31U, 31X, 40U, 40X, 41U,
41X, 50U, 50X, 51U, 51X, 60U, 61U,
70U, 71U
Speaker Assembly (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
System Board Rail (Models 10U, 10X,
11U, 11X, 15U, 15X, 16U, 16X, 20U,
20X, 21U, 21X, 30U, 30X, 31U, 31X,
40U, 40X, 41U, 41X, 50U, 50X, 51U,
51X, 60U, 61U, 70U, 71U)
IBM Netfinity 3000 - Type 8476
FRU
No.
03K9607
03K9626
205
Keyboards
Keyboards
FRU No.
Arabic
37L2555
37L0818
02K0870
37L2556
37L0819
02K0871
37L2557
37L0820
02K0872
37L2571
37L0817
02K0869
37L2558
37L0821
02K0873
37L2585
37L0848
02K0900
37L2559
37L0822
02K0874
37L2560
37L0823
02K0875
37L2561
37L0824
02K0876
37L2562
37L0825
02K0877
37L0913
37L2552
37L0815
02K0863
37L2563
37L0826
02K0878
37L2564
37L0827
02K0879
37L2565
37L0828
02K0880
37L2566
37L0829
02K0881
37L2567
37L0830
02K0882
37L2568
37L0831
02K0883
37L0847
02K0899
02K0901
37L0849
76H0935
Belgian-French
Belgian-UK/Dutch
Brazil/Portugal
Bulgarian
Chinese/US
Czech
Danish
Dutch
French
French/Canadian - 58
French/Canadian - 445
German
Greek
Hebrew
Hungarian
Icelandic
Italian
Japanese
Korean
206
Netfinity Server HMM
Keyboards
FRU No.
Norwegian
37L2569
37L0832
02K0884
37L2570
37L0833
02K0885
37L2571
37L0834
02K0886
37L2572
37L0835
02K0887
37L2573
37L0836
02K0888
37L2574
37L0837
02K0889
37L2575
37L0838
02K0890
37L2576
37L0839
02K0891
37L2553
37L0816
02K0867
37L2577
37L0840
02K0892
37L2578
37L0841
02K0893
37L2587
37L0850
02K0902
37L2579
37L0842
02K0894
37L2580
37L0843
02K0895
37L2581
37L0844
02K0896
37L2551
37L0814
02K0861
37L2583
37L0846
02K0898
37L2582
37L0845
02K0897
Polish
Portuguese
Romanian
Russian
Serbian/Cyrillic
Slovak
Spanish
Spanish - Latin America
Swedish/Finnish
Swiss French/German
Thailand
Turkish - 179
Turkish - 440
UK English
US English
UK English (ISO Compliant)
Yugoslavia/Lithuania
IBM Netfinity 3000 - Type 8476
207
Power cords
Power Cords
FRU No.
Arabic
Belgium
Bulgaria
Czech Republic
Denmark
Finland
France
Germany
Hungary
Israel
Italy
Latvia
Netherlands
Norway
Poland
Portugal
Serbia
Slovakia
South Africa
Spain
Switzerland
Switzerland (French/German)
U.S. English
U.K./Ireland
Yugoslavia
14F0033
1339520
1339520
1339520
13F9997
1339520
1339520
1339520
1339520
14F0087
14F0069
1339520
1339520
1339520
1339520
1339520
1339520
1339520
14F0015
1339520
1339520
14F0051
62X1045
14F0033
1339520
208
Netfinity Server HMM
Related service information
Important
The service procedures are designed to help you
isolate problems. They are written with the
assumption that you have model-specific training on
all computers, or that are familiar with the computers,
functions, terminology, and service information
provided in this supplement and the PS/2 Hardware
Maintenance Manual (part number 83G8990, form
number S52G-9971-02).
Safety information . . . . . . . . . . . .
General safety . . . . . . . . . . . .
Electrical safety
. . . . . . . . . . .
Safety inspection guide
. . . . . . .
Handling electrostatic discharge-sensitive
Grounding requirements
. . . . . . .
Battery notice (lithium)
. . . . . . . . .
Battery notice (nickel cadmium)
. . . . .
Laser compliance statement . . . . . . .
Send us your comments!
. . . . . . . .
Problem determination tips
. . . . . . .
Phone numbers, U.S. and Canada . . . .
Trademarks
. . . . . . . . . . . . . .
 Copyright IBM Corp. 1999
. . . .
. . . .
. . . .
. . . .
devices
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
. . . .
210
210
211
212
214
214
215
218
252
254
255
256
258
209
Safety information
The following section contains the safety information that
you need to be familiar with before servicing an IBM
mobile computer.
General safety
Follow these rules to ensure general safety:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
210
Observe good housekeeping in the area of the
machines during and after maintenance.
When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally
between your feet.
3. Use a slow lifting force. Never move suddenly
or twist when you attempt to lift.
4. Lift by standing or by pushing up with your leg
muscles; this action removes the strain from the
muscles in your back. Do not attempt to lift any
objects that weigh more than 16 kg (35 lb) or
objects that you think are too heavy for you.
Do not perform any action that causes hazards to the
customer, or that makes the equipment unsafe.
Before you start the machine, ensure that other
service representatives and the customer's personnel
are not in a hazardous position.
Place removed covers and other parts in a safe
place, away from all personnel, while you are
servicing the machine.
Keep your tool case away from walk areas so that
other people will not trip over it.
Do not wear loose clothing that can be trapped in the
moving parts of a machine. Ensure that your sleeves
are fastened or rolled up above your elbows. If your
hair is long, fasten it.
Insert the ends of your necktie or scarf inside clothing
or fasten it with a nonconductive clip, approximately 8
centimeters (3 inches) from the end.
Do not wear jewelry, chains, metal-frame eyeglasses,
or metal fasteners for your clothing.
Remember: Metal objects are good electrical
conductors.
Wear safety glasses when you are: hammering,
drilling soldering, cutting wire, attaching springs, using
solvents, or working in any other conditions that might
be hazardous to your eyes.
After service, reinstall all safety shields, guards,
labels, and ground wires. Replace any safety device
that is worn or defective.
Reinstall all covers correctly before returning the
machine to the customer.
Netfinity Server HMM
Electrical safety
Caution
Electrical current from power, telephone, and
communication cables can be hazardous. To avoid
personal injury or equipment damage, disconnect the
attached power cords, telecommunication systems,
networks, and modems before you open the server
covers, unless instructed otherwise in the installation
and configuration procedures.
Observe the following rules when working on electrical
equipment.
Important
Use only approved tools and test equipment. Some
hand tools have handles covered with a soft material
that does not insulate you when working with live
electrical currents.
Many customers have, near their equipment, rubber
floor mats that contain small conductive fibers to
decrease electrostatic discharges. Do not use this
type of mat to protect yourself from electrical shock.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Find the room emergency power-off (EPO) switch,
disconnecting switch, or electrical outlet. If an
electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
Do not work alone under hazardous conditions or
near equipment that has hazardous voltages.
Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
Before you start to work on the machine, unplug the
power cord. If you cannot unplug it, ask the customer
to power-off the wall box that supplies power to the
machine and to lock the wall box in the off position.
If you need to work on a machine that has exposed
electrical circuits, observe the following precautions:
– Ensure that another person, familiar with the
power-off controls, is near you.
–
Remember: Another person must be there to
switch off the power, if necessary.
Use only one hand when working with
powered-on electrical equipment; keep the other
hand in your pocket or behind your back.
Remember: There must be a complete circuit to
cause electrical shock. By observing the above
Related service information
211
–
–
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
rule, you may prevent a current from passing
through your body.
When using testers, set the controls correctly
and use the approved probe leads and
accessories for that tester.
Stand on suitable rubber mats (obtained locally,
if necessary) to insulate you from grounds such
as metal floor strips and machine frames.
Observe the special safety precautions when you
work with very high voltages; these instructions are in
the safety sections of maintenance information. Use
extreme care when measuring high voltages.
Regularly inspect and maintain your electrical hand
tools for safe operational condition.
Do not use worn or broken tools and testers.
Never assume that power has been disconnected
from a circuit. First, check that it has been
powered-off.
Always look carefully for possible hazards in your
work area. Examples of these hazards are moist
floors, nongrounded power extension cables, power
surges, and missing safety grounds.
Do not touch live electrical circuits with the reflective
surface of a plastic dental mirror. The surface is
conductive; such touching can cause personal injury
and machine damage.
Do not service the following parts with the power on
when they are removed from their normal operating
places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct
grounding of the units.)
If an electrical accident occurs:
– Use caution; do not become a victim
yourself.
– Switch off power.
– Send another person to get medical aid.
Safety inspection guide
The intent of this inspection guide is to assist you in
identifying potentially unsafe conditions on these products.
Each machine, as it was designed and built, had required
safety items installed to protect users and service
personnel from injury. This guide addresses only those
items. However, good judgment should be used to identify
potential safety hazards due to attachment of non-IBM
features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine
how serious the apparent hazard could be and whether
you can continue without first correcting the problem.
212
Netfinity Server HMM
Consider these conditions and the safety hazards they
present:
Ÿ
Ÿ
Ÿ
Electrical hazards, especially primary power (primary
voltage on the frame can cause serious or fatal
electrical shock).
Explosive hazards, such as a damaged CRT face or
bulging capacitor
Mechanical hazards, such as loose or missing
hardware
The guide consists of a series of steps presented in a
checklist. Begin the checks with the power off, and the
power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or
sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition.
Use a meter to measure third-wire ground
continuity for 0.1 ohm or less between the
external ground pin and frame ground.
b. The power cord should be the appropriate type
as specified in the parts listings.
c. Insulation must not be frayed or worn.
4. Remove the cover.
5. Check for any obvious non-IBM alterations. Use
good judgment as to the safety of any non-IBM
alterations.
6. Check inside the unit for any obvious unsafe
conditions, such as metal filings, contamination, water
or other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws
or rivets) have not been removed or tampered with.
Related service information
213
Handling electrostatic
discharge-sensitive devices
Any computer part containing transistors or integrated
circuits (ICs) should be considered sensitive to electrostatic
discharge (ESD). ESD damage can occur when there is a
difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the
part, the work mat, and the person handling the part are all
at the same charge.
Notes:
1. Use product-specific ESD procedures when they
exceed the requirements noted here.
2. Make sure that the ESD protective devices you use
have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts:
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Keep the parts in protective packages until they are
inserted into the product.
Avoid contact with other people.
Wear a grounded wrist strap against your skin to
eliminate static on your body.
Prevent the part from touching your clothing. Most
clothing is insulative and retains a charge even when
you are wearing a wrist strap.
Use the black side of a grounded work mat to provide
a static-free work surface. The mat is especially
useful when handling ESD-sensitive devices.
Select a grounding system, such as those listed
below, to provide protection that meets the specific
service requirement.
Note: The use of a grounding system is desirable
but not required to protect against ESD
damage.
–
–
–
Attach the ESD ground clip to any frame ground,
ground braid, or green-wire ground.
Use an ESD common ground or reference point
when working on a double-insulated or
battery-operated system. You can use coax or
connector-outside shells on these systems.
Use the round ground-prong of the ac plug on
ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for
operator safety and correct system function. Proper
grounding of the electrical outlet can be verified by a
certified electrician.
214
Netfinity Server HMM
Battery notice (lithium)
Caution
The lithium battery can cause a fire, explosion, or
severe burn. Do not recharge it, remove its polarized
connector, disassemble it, heat it above 100°C
(212°F), incinerate it, or expose its cell contents to
water. Dispose of the battery as required by local
ordinances or regulations. Use only the battery in the
appropriate parts listing. Use of an incorrect battery
can result in ignition or explosion of the battery.
A pilha de lítio representa risco de incêndio, explosão
ou queimaduras graves. Não recarregue, desmonte ou
exponha a pilha a temperaturas superiores a 100°C
(212°F), não a incinere ou ponha o conteúdo da
respectiva célula em contacto com a água nem
remova o respectivo conector polarizado. Destrua a
pilha de acordo com as normas ou regulamentações
locais. Utilize apenas a pilha com o "part-number"
indicado nas listas apropriadas. A utilização de uma
pilha incorrecta pode resultar na igniçãou explosão da
mesma.
100 C (212 F)
Elle présente des risques d'incendie, d'explosion ou
de brûlures graves. Ne la rechargez pas, ne retirez
pas son connecteur polarisé et ne la démontez pas.
Ne l'exposez pas à une temperature supérieure à
100°C, ne la faites pas brûler et n'en exposez pas le
contenu à l'eau. Mettez la pile au rebut conformément
à la réglementation en vigueur. Une pile inappropriée
risque de prendre feu ou d'exploser.
Related service information
215
Caution Continued
Die Systembatterie ist eine Lithiumbatterie. Sie kann
sich entzünden, explodieren oder schwere
Verbrennungen hervorrufen. Batterien dieses Typs
dürfen nicht aufgeladen, zerlegt, über 100 C erhitzt
oder verbrannt werden. Auch darf ihr Inhalt nicht mit
Wasser in Verbindung gebracht oder der zur richtigen
Polung angebrachte Verbindungsstecker entfernt
werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Batterie nur Batterien des Typs
verwenden, der in der Ersatzteilliste aufgeführt ist.
Der Einsatz falscher Batterien kann zu Entzündung
oder Explosion führen.
A l¡tium elemek tüzet, robban st vagy komoly égési
sérüléseket okozhatnak. Nem szabad £jratölteni,
polariz lt csatlakoz¢j b¢l elt vol¡tani, szétszedni, 100°C
(212°F) feletti hímérsékletre felhev¡teni, elégetni, vagy
az elem cell j nak tartalm t nedvesség hat s nak
kitenni. Az elem megsemmis¡tésének a helyi
rendelkezések és szab lyzatok alapj n kell történnie.
Csak a tartozékok list j ban meghat rozott t¡pus£
elemeket haszn lja. Nem megfelelí elem haszn lata
esetén az elem felhevülhet és szétrobbanhat.
La batteria di supporto e una batteria al litio e puo
incendiarsi, esplodere o procurare gravi ustioni.
Evitare di ricaricarla, smontarne il connettore
polarizzato, smontarla, riscaldarla ad una temperatura
superiore ai 100 gradi centigradi, incendiarla o gettarla
in acqua. Smaltirla secondo la normativa in vigore
(DPR 915/82, successive disposizioni e disposizioni
locali). L'impiego di una batteria non adatta potrebbe
determinare l'incendio o l'esplosione della batteria
stessa.
216
Netfinity Server HMM
Caution Continued
Li batéria mô¶e zapríåiniù po¶iar, v–buch alebo ùa¶ké
popáleniny. Batériu nanabíjajte neodstranujte
polarizované konektory, nerozoberajte, nezohrievajte
nad 100°C ( 212°F ), nespopolnujte ju alebo
nepokladajte ålánky batérie do vody. Zbavte sa
batérie podïa po¶adovan–ch lokálnych predpisov a
pravidiel. Pou¶ite iba v–robcom odporúåanú batériu.
Pou¶itie nevhodnej batérie mô- ¶e zapríåiniù
vznietenie alebo v–buch batérie.
La bateria de repuesto es una bateria de litio y puede
provocar incendios, explosiones o quemaduras
graves. No la recargue, ni quite el conector
polarizado, ni la desmonte, ni caliente por encima de
los 100°C (212°F), ni la incinere ni exponga el
contenido de sus celdas al agua. Deséchela tal como
dispone la normativa local.
Related service information
217
Battery notice (nickel cadmium)
Caution
Some batteries contain nickel and cadmium. Do not
disassemble it, recharge it, throw it into fire or water,
or short-circuit it. Dispose of the battery as required
by local ordinances or regulations. Use only the
battery in the appropriate parts listing. Use of an
incorrect battery can result in ignition or explosion of
the battery.
Algumas pilhas contêm uma pequena quantidade de
níquel e cádmio. Não desmonte, recarregue ou
ponha a pilha em contacto com fogo ou água nem lhe
provoque curto-circuitos. Destrua a pilha de acordo
com as normas ou regulamentações locais. Utilize
apenas a pilha com o "part-number" indicado nas
listas apropriadas. A utilizaçãode uma pilha incorrecta
pode resultar na ignição ou explosão da mesma.
Certaines batteries de secours contiennent du nickel
et du cadmium. Ne les démontez pas, ne les
rechargez pas, ne les exposez ni au feu ni à l'eau.
Ne les mettez pas en court-circuit. Pour les mettre au
rebut, conformez-vous à la réglementation en vigueur.
Lorsque vous remplacez la pile de sauvegarde ou
celle de l'horloge temps réel, veillez à n'utiliser que les
modèles cités dans la liste de pièces détachées
adéquate. Une batterie ou une pile inappropriée
risque de prendre feu ou d'exploser.
Die Bereitschaftsbatterie, die sich unter dem
Diskettenlaufwerk befindet, kann geringe Mengen
Nickel und Cadmium enthalten. Sie darf nur durch die
Verkaufsstelle oder den IBM Kundendienst
ausgetauscht werden. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder
Wasser ausgesetzt werden. Die Batterie kann
schwere Verbrennungen oder Verätzungen
verursachen. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Bereitschafts- oder Systembatterie nur
Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher
Batterien kann zu Entzündung oder Explosion führen.
218
Netfinity Server HMM
Caution Continued
Az elemek egyes fajt i kis mennyiségû nikkelt és
kadmiumot tartalmaznak. Nem szabad szétszedni,
£jratölteni, tûzbe vagy v¡zbe dobni illetve rövidre z rni.
Az elem megsemmis¡tésének a helyi rendelkezések
és szab lyzatok alapj n kell történnie. Csak a
tartozékok list j ban meghat rozott t¡pus£ elemeket
haszn lja. Nem megfelelí elem haszn lata esetén az
elem felhevülhet és szétrobbanhat.
Alcune batterie di riserva contengono una piccola
quantità di nichel e cadmio. Non smontarle, ricaricarle,
gettarle nel fuoco o nell'acqua né cortocircuitarle.
Smaltirle secondo la normativa in vigore (DPR 915/82,
successive disposizioni e disposizioni locali). Quando
si sostituisce la batteria dell'RTC (real time clock) o la
batteria di supporto, utilizzare soltanto i tipi inseriti
nell'appropriato Catalogo parti. L'impiego di una
batteria non adatta potrebbe determinare l'incendio o
l'esplosione della batteria stessa.
Niektoré batérie majú malé mno¶stvo niklu (Ni) a
kadmia (Cd). Batériu nerozoberajte, nenabíjajte,
neukladajte do oh»a alebo vody a neskratujte
ju.Zbavte sa batérie podïa po¶adovan–ch lokálnych
predpisov a pravidiel. Pou¶ite iba v–robcom
odporúåanú batériu. Pou¶itie nevhodnej batérie mô¶e zapríåiniù vznietenie alebo v–buch batérie.
Algunas baterías de reserva contienen una pequeña
cantidad de níquel y cadmio. No las desmonte, ni
recargue, ni las eche al fuego o al agua ni las
cortocircuite. Deséchelas tal como dispone la
normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una
batería no apropiada puede provocar la ignición o
explosión de la misma.
Related service information
219
DANGER
To avoid a shock hazard, do not connect or
disconnect any cables or perform installation,
maintenance, or reconfiguration of this
product during an electrical storm.
To avoid shock hazard:
Ÿ
The power cord must be connected to a
properly wired and grounded receptacle.
Ÿ
Any equipment to which this product will
be attached must also be connected to
properly wired receptacles.
When possible, use one hand to connect or
disconnect signal cables to prevent a
possible shock from touching two surfaces
with different electrical potentials.
Electrical current from power, telephone, and
communications cables is hazardous. To
avoid shock hazard, connect and disconnect
cables as described following when
installing, moving, or opening covers of this
product or attached devices.
To Connect
To Disconnect
1. Turn Everything OFF.
1. Turn Everything OFF.
2. First, attach all cables to
devices.
2. First, remove power cord(s)
from outlet.
3. Attach signal cables to
receptacles.
3. Remove signal cables from
receptacles.
4. Attach power cord(s) to
outlet.
4. Remove all cables from
devices.
5. Turn device ON.
NOTE: In the UK, by law, the
telephone cable must be
connected after the power cord.
220
Netfinity Server HMM
NOTE: In the UK, the power
cord must be disconnected after
the telephone cable.
Caution:
When replacing the battery, use only IBM Part Number
33F8354 or an equivalent type battery recommended
by the manufacturer. If your system has a module
containing a lithium battery, replace it only with the
same module type made by the same manufacturer.
The battery contains lithium and can explode if not
properly used, handled, or disposed of.
Do not:
Ÿ
Ÿ
Ÿ
Throw or immerse into water
Heat to more than 100°C (212°F)
Repair or disassemble
Dispose of the battery as required by local ordinances
or regulations.
Caution:
When a CD-ROM drive is installed, note the following.
Use of controls or adjustments or performance of
procedures other than those specified herein might
result in hazardous radiation exposure.
Removing the covers of the CD-ROM drive could result
in exposure to hazardous laser radiation. There are no
serviceable parts inside the CD-ROM drive. Do not
remove the CD-ROM drive covers.
DANGER
Some CD-ROM drives contain an embedded
Class 3A or Class 3B laser diode. Note the
following.
Laser radiation when open. Do not stare into
the beam, do not view directly with optical
instruments, and avoid direct exposure to the
beam.
Related service information
221
k32 kg (70.5
lbs)
k55 kg (121.2
lbs)
Caution:
Use safe lifting practices when lifting your machine.
Caution:
The Power Control button on the front of the server
does not turn off the electrical current supplied to the
server. The server also might have more than one
power cord. To remove all electrical current from the
server, ensure that all power cords are disconnected
from the power source.
Caution:
When the power cord bracket option is installed on the
power cord, the server must be plugged to a power
source that is easily accessible.
Caution:
When unlocked, the server door will not support the
weight of the server. To avoid personal injury, be sure
to remove or lock the server door before moving or
lifting the server.
222
Netfinity Server HMM
Caution:
Never remove the cover on a power supply or any part
(power backplane and AC box) that has the following
label attached.
Hazardous voltage, current, and energy levels are
present inside the power supplies, power backplane,
and AC box. There are no serviceable parts inside the
power supplies, power backplane, or AC box. If you
suspect a problem with one of these parts, contact an
IBM service technician.
Caution:
Electrical current from power, telephone, and
communication cables can be hazardous. To avoid
personal injury or equipment damage, disconnect the
attached power cords, telecommunications systems,
networks, and modems before you open the server
covers, unless instructed otherwise in the installation
and configuration procedures.
Caution:
The power cable to the fan should be disconnected
whenever the fan assembly is not installed in the
server; otherwise, the fan might start turning while you
are holding it and the fan blades could injure your
fingers.
>50 kg (110
lbs)
Caution:
Do not place any object weighing more than 50 kg (110
lbs) on top of the rack model of the server.
Related service information
223
PERIGO
Para evitar choques elétricos, não conecte ou
desconecte nenhum cabo, nem efetue
instalação, manutenção ou reconfiguração
deste produto durante uma tempestade com
raios.
Para evitar choques elétricos:
Ÿ
O cabo de alimentação deve ser
conectado a um receptáculo
corretamente instalado e aterrado.
Ÿ
Todos os equipamentos aos quais este
produto será conectado devem também
ser conectados a receptáculos
corretamente instalados.
Quando possível, utilize uma das mãos para
conectar ou desconectar cabos de sinal, para
evitar um possível choque ao tocar duas
superfícies com potenciais elétricos
diferentes.
A corrente elétrica proveniente de cabos de
alimentação, de telefone e de comunicação é
perigosa. Para evitar choques elétricos,
conecte e desconecte os cabos conforme
descrito a seguir, ao instalar, movimentar ou
abrir tampas deste produto ou de
dispositivos conectados.
Para Conectar
1. DESLIGUE tudo.
2. Conecte primeiro todos os
cabos nos dispositivos.
3. Conecte os cabos de sinal
nos receptáculos.
4. Conecte o(s) cabo(s) de
alimentação nas tomadas.
5. LIGUE o dispositivo.
224
Netfinity Server HMM
Para Desconectar
1. DESLIGUE tudo.
2. Remova primeiro o(s)
cabo(s) de alimentação das
tomadas.
3. Remova os cabos de sinal
dos receptáculos.
4. Remova todos os cabos
dos dispositivos.
cuidado:
Ao substituir a bateria, utilize apenas o Número de
Peça IBM 33F8354 ou um tipo de bateria equivalente
recomendado pelo fabricante. Se seu sistema possuir
um módulo com uma bateria de lítio, substitua-o
apenas pelo mesmo tipo de módulo, produzido pelo
mesmo fabricante. A bateria contém lítio e pode
explodir se não for utilizada, manuseada e descartada
de forma adequada.
Não:
Ÿ
Ÿ
Ÿ
Jogue ou coloque na água
Aqueça a mais de 100°C (212°F)
Conserte nem desmonte.
Descarte a bateria conforme requerido pelas
disposições e regulamentações locais.
cuidado:
Quando uma unidade de CD-ROM estiver instalada,
observe o seguinte.
A utilização de controles ou ajustes ou a execução de
procedimentos diferentes daqueles especificados
nesta publicação pode resultar em exposição perigosa
à radiação.
A remoção das tampas da unidade de CD-ROM pode
resultar em exposição a radiação perigosa de laser.
Não existem peças que possam ser consertadas no
interior da unidade de CD-ROM. Não remova as
tampas da unidade de CD-ROM.
PERIGO
Algumas unidades de CD-ROM contém um
diodo de laser da Classe 3A ou da Classe 3B.
Observe o seguinte.
Radiação de laser quando aberto. Não olhe
diretamente para o feixe de laser, não olhe
diretamente com instrumentos óticos, e evite
exposição direta ao raio.
Related service information
225
k32 kg (70,5
lbs)
k55 kg (121,2
lbs)
cuidado:
Utilize práticas seguras para levantamento de peso ao
levantar sua máquina.
cuidado:
O botão de Controle de Energia na parte frontal do
servidor não desliga a corrente elétrica fornecida ao
servidor. O servidor pode também possuir mais que
um cabo de alimentação. Para remover tda a corrente
elétrica do servidor, assegure que todos os cabos de
alimentação estejam desconectados da fonte de
energia.
cuidado:
Quando o suporte do cabo de alimentação estiver
instalado no cabo de alimentação, o servidor deve
estar conectado a uma fonte de energia de fácil
acesso.
cuidado:
Quando destravada, a porta do servidor não suporta o
peso do servidor. Para evitar ferimentos pessoais,
certifique-se de remover ou travar a porta do servidor
antes de mover ou levantar o servidor.
226
Netfinity Server HMM
cuidado:
Nunca remova a tampa de uma fonte de alimentação
ou qualquer peça (painel traseiro de força ou AC box)
que contenha a seguinte etiqueta.
Níveis perigosos de tensão, corrente e energia estão
presentes no interior das fontes de alimentação, painel
traseiro de força ou AC box. Não existem peças que
possam ser consertadas no interior da fonte de
alimentação, painel traseiro de força ou AC box. Se
suspeitar de problemas em uma dessas peças, entre
em contato com um representante técnico IBM.
cuidado:
A corrente elétrica proveniente de cabos de
alimentação, de telefone e de comunicação é perigosa.
Para evitar ferimentos pessoais ou danos aos
equipamentos, desconecte os cabos de alimentação,
sistemas de telecomunicação, redes e modems antes
de abrir as tampas do servidor, a menos que receba
outras instruções nos procedimentos de instalação e
configuração.
cuidado:
O cabo de energia do ventilador deve permanecer
desconectado sempre que o conjunto do ventilador
não estiver instalado no servidor; caso contrário, o
ventilador pode começar a girar enquanto estiver em
suas mãos, e as lâminas do ventilador podem ferir
seus dedos.
>50 kg (110
lbs)
cuidado:
Não coloque qualquer objeto com peso superior a 50
kg (110 lbs) sobre o modelo de gaveta do servidor.
Related service information
227
228
Netfinity Server HMM
Related service information
229
230
Netfinity Server HMM
Related service information
231
232
Netfinity Server HMM
DANGER
Pour éviter tout risque de choc électrique, ne
manipulez aucun câble et n'effectuez aucune
opération d'installation, d'entretien ou de
reconfiguration de ce produit au cours d'un
orage.
Pour éviter tout risque de choc électrique :
Ÿ
Les cordons d'alimentation du présent
produit et de tous les appareils qui lui
sont connectés doivent être branchés
sur des socles de prise de courant
correctement câblés et mis à la terre.
Afin d'éviter tout risque de choc électrique
provenant d'une différence de potentiel de
terre, n'utilisez qu'une main, lorsque cela est
possible, pour connecter ou déconnecter les
cordons d'interface.
Le courant électrique passant dans les
câbles de communication, ou les cordons
téléphoniques et d'alimentation peut être
dangereux. Pour éviter tout risque de choc
électrique, lorsque vous installez ou que
vous déplacez le présent produit ou des
périphériques qui lui sont raccordés,
reportez-vous aux instructions ci-dessous
pour connecter et déconnecter les différents
cordons.
Connexion
Déconnexion
1. Mettez les unités hors
tension.
2. Commencez par brancher
tous les cordons sur les
unités.
3. Branchez les câbles
d'interface sur les prises.
4. Branchez les cordons
d'alimentation sur un socle
de prise de courant.
5. Mettez les unités sous
tension.
1. Mettez les unités hors
tension.
2. Commencez pas
débrancher les cordons
alimentation des socles de
prise de courant.
3. Débranchez les câbles
d'interface des prises.
4. Débranchez tous les câbles
des unités.
Related service information
233
attention:
Remplacez la pile usagée par une pile de référence
identique exclusivement - voir la référence IBM - ou
par une pile équivalente recommandée par le fabricant.
Si votre système est doté d'un module contenant une
pile au lithium, vous devez le remplacer uniquement
par un module identique, produit par le même
fabricant. La pile contient du lithium et présente donc
un risque d'explosion en cas de mauvaise
manipulation ou utilisation.
Ÿ
Ÿ
Ÿ
Ne la jetez pas à l'eau.
Ne l'exposez pas à une température supérieure à
100 °C.
Ne cherchez pas à la réparer ou à la démonter.
Pour la mise au rebut, reportez-vous à la
réglementation en vigueur.
attention:
Si une unité de CD-ROM est installée, prenez
connaissance des informations suivantes :
Pour éviter tout risque d'exposition au rayon laser,
respectez les consignes de réglage et d'utilisation des
commandes, ainsi que les procédures décrites dans le
présent document.
Pour éviter une exposition directe au rayon laser,
n'ouvrez pas l'unité de CD-ROM. Vous ne pouvez
effectuer aucune opération de maintenance à
l'intérieur.
DANGER
Certaines unités de CD-ROM contiennent une
diode laser de classe 3A ou 3B. Prenez
connaissance des informations suivantes :
Rayonnement laser lorsque le carter est
ouvert. Évitez de regarder fixement le
faisceau ou de l'observer à l'aide
d'instruments optiques. Évitez une exposition
directe au rayon.
234
Netfinity Server HMM
k32 kg
k55 kg
attention:
Ce produit pèse un poids considérable. Faites-vous
aider pour le soulever.
attention:
Le bouton de mise sous tension/hors tension situé sur
la face avant du serveur ne coupe pas l'arrivée de
courant électrique à l'inérieur de la machine. Il se peut
que votre serveur dispose de plusieurs cordons
d'alimentation. Pour isoler totalement le serveur du
réseau électrique, débranchez tous les cordons
d'alimentation des socle de prise de courant.
attention:
Lorsqu'une patte de fixation du cordon d'alimentation
est installée branchez le serveur sur une prise de
courant électrique facile d'accès.
attention:
Une fois déverrouillé, le volet du serveur ne supporte
pas le poids de ce dernier. Pour éviter tout accident,
retirez ou verrouillez le volet du serveur avant de
déplacer ou de soulever ce dernier.
Related service information
235
attention:
N'ouvrez jamais le bloc d'alimentation ou tout élément
(fond de panier du bloc ou boîtier d'alimentation en
courant alternatif) sur lequel est apposé l'étiquette
ci-dessous.
Des tensions et des courants dangereux sont présents
à l'intérieur des blocs d'alimentation, de leurs fonds de
panier et du boîtier d'alimentation en courant alternatif.
Ces éléments ne peuvent pas être réparés. Si vous
pensez qu'ils peuvent être à l'origine d'un incident,
prenez contact avec un technicien de maintenance
IBM.
attention:
Le courant électrique circulant dans les câbles de
communication et les cordons téléphoniques et
d'alimentation peut être dangereux. Pour votre sécurité
et celle de l'équipement, avant de retirer les carters du
serveur, mettez celui-ci hors tension et déconnectez
ses cordons d'alimentation, ainsi que les câbles qui le
relient aux réseaux, aux systèmes de
télécommunication et aux modems (sauf instruction
contraire mentionnée dans les procédures
d'installation et de configuration).
attention:
Vous devez débrancher le cordon d'alimentation du
ventilateur avant d'installer ce dernier dans le serveur,
sinon le ventilateur peut se mettre en route et vous
risquez de vous blesser.
>50 kg
attention:
Ne posez pas d'objet dont le poids dépasse 50 kg sur
les modèles tiroir de serveur.
236
Netfinity Server HMM
VORSICHT
Aus Sicherheitsgründen bei Gewitter an
diesem Gerät keine Kabel anschließen oder
lösen. Ferner keine Installations-, Wartungsoder Rekonfigurationsarbeiten durchführen.
Aus Sicherheitsgründen:
Ÿ
Ÿ
Gerät nur an eine
Schutzkontaktsteckdose mit
ordnungsgemäß geerdetem
Schutzkontakt anschließen.
Alle angeschlossenen Geräte ebenfalls
an Schutzkontaktsteckdosen mit
ordnungsgemäß geerdetem
Schutzkontakt anschließen.
Signalkabel möglichst einhändig anschließen
oder lösen, um einen Stromschlag durch
Berühren von Oberflächen mit
unterschiedlichem elektrischem Potential zu
vermeiden.
Elektrische Spannungen von Netz-, Telefonund Datenübertragungsleitungen sind
gefährlich. Um einen Stromschlag zu
vermeiden, nur nach den Anweisungen
arbeiten, die für Installation, Transport oder
Öffnen von Gehäusen dieses Produkts oder
angeschlossenen Einheiten gelten.
Kabel anschließen
Kabel lösen
1. Alle Geräte ausschalten und
Netzstecker ziehen.
2. Zuerst alle Kabel an
Einheiten anschließen.
3. Signalkabel an
Anschlußbuchsen
anschließen.
4. Netzstecker an Steckdose
anschließen.
5. Gerät einschalten.
1. Alle Geräte ausschalten.
2. Zuerst Netzstecker von
Steckdose lösen.
3. Signalkabel von
Anschlußbuchsen lösen.
4. Alle Kabel von Einheiten
lösen.
Related service information
237
achtung:
Eine verbrauchte Batterie nur durch eine Batterie mit
der IBM Teilenummer 33F8354 oder durch eine vom
Hersteller empfohlene Batterie ersetzen. Wenn Ihr
System ein Modul mit einer Lithium-Batterie enthält,
ersetzen Sie es immer mit dem selben Modultyp vom
selben Hersteller. Die Batterie enthält Lithium und
kann bei unsachgemäßer Verwendung, Handhabung
oder Entsorgung explodieren.
Die Batterie nicht
Ÿ
Ÿ
Ÿ
mit Wasser in Berührung bringen.
über 100 C erhitzen.
reparieren oder zerlegen.
Die örtlichen Bestimmungen für die Entsorgung von
Sondermüll beachten.
achtung:
Wenn ein CD-ROM-Laufwerk installiert ist, beachten
Sie folgendes. Steuer- und Einstellelemente sowie
Verfahren nur entsprechend den Anweisungen im
vorliegenden Handbuch einsetzen. Andernfalls kann
gefährliche Laserstrahlung auftreten.
Das Entfernen der Abdeckungen des
CD-ROM-Laufwerks kann zu gefährlicher
Laserstrahlung führen. Es befinden sich keine Teile
innerhalb des CD-ROM-Laufwerks, die vom Benutzer
gewartet werden müssen. Die Verkleidung des
CD-ROM-Laufwerks nicht öffnen.
VORSICHT
Manche CD-ROM-Laufwerke enthalten eine
eingebaute Laserdiode der Klasse 3A oder
3B. Die nachfolgend aufgeführten Punkte
beachten.
Laserstrahlung bei geöffneter Tür. Niemals
direkt in den Laserstrahl sehen, nicht direkt
mit optischen Instrumenten betrachten und
den Strahlungsbereich meiden.
238
Netfinity Server HMM
k32 kg
k55 kg
achtung:
Beim Anheben der Maschine die vorgeschriebenen
Sicherheitsbestimmungen beachten.
achtung:
Mit dem Betriebsspannungsschalter an der Vorderseite
des Servers wird die Stromversorgung für den Server
nicht unterbrochen. Der Server könnte auch mehr als
ein Netzkabel auweisen. Um die gesamte
Stromversorgung des Servers auszuschalten, muß
sicherestellt werden, daß alle Netzkabel aus den
Netzsteckdosen herausgezogen wurdn.
achtung:
Wenn am Netzkabel eine Kabelhalterung angebracht
ist, uß der Server an eine leicht zugängliche
tzsteckdose angeschlosen rden.
achtung:
Bei geöffneter Tür kann die Servertür nicht das
Gewicht des Servers tragen. Zur Vermeidung von
Verletzungsgefahren vor dem Transportieren oder
Anheben des Servers die Servertür abnehmen oder
verschließen.
Related service information
239
achtung:
Die Abdeckung oder eine Komponente eines Netzteils
(Rückwandplatine oder Netzspannungsgehäuse), die
wie nachfolgend aufgeführt gekennzeichnet ist, darf
keinesfalls entfernt werden.
In Netzteilen, Rückwandplatinen und
Netzspannungsgehäusen können gefährliche
Spannungen anliegen. In Netzteilen,
Rückwandplatinen oder Netzspannungsgehäusen sind
keine Teile vorhanden, die vom Benutzer gewartet
werden müssen. Besteht der Verdacht, daß an einem
dieser Teile ein Fehler aufgetreten ist, ist ein IBM
Kundendiensttechniker zu verständigen.
achtung:
An Netz-, Telefon- und Datenleitungen können
gefährliche elektrische Spannungen anliegen. Um eine
Gefährdung des Benutzers oder Beschädigung des
Geräts zu vermeiden, ist der Server auszuschalten. Die
Verbindung zu den angeschlossenen Netzkabeln,
Telekommunikationssystemen, Netzwerken und
Modems ist vor dem Öffnen des Servergehäuses zu
unterbrechen (sofern in Installations- und
Konfigurationsanweisungen nicht anders angegeben).
achtung:
Das Netzkabel des Lüfters sollte herausgezogen sein,
wenn der Lüfter nicht in den Server eingebaut ist.
Andernfalls könnte der Lüfter zu drehen beginnen,
solange Sie ihn in der Hand halten. Hierbei kann es zu
Verletzungen durch die Ventilatorblätter kommen.
>50 kg
achtung:
Legen Sie keine Gegenstände, die mehr als 50 kg
wiegen, auf das Einschubmodell des Servers.
240
Netfinity Server HMM
PERICOLO
Per evitare il pericolo di scosse elettriche
durante i temporali, non collegare o
scollegare cavi, non effettuare l'installazione,
la manutenzione o la riconfigurazione di
questo prodotto.
Per evitare il pericolo di scosse elettriche:
Ÿ
Ÿ
collegare il cavo di alimentazione ad una
presa elettrica correttamente cablata e
munita di terra di sicurezza;
collegare qualsiasi apparecchiatura
collegata a questo prodotto ad una
presa elettrica correttamente cablata e
munita di terra di sicurezza.
Quando possibile, collegare o scollegare i
cavi di segnale con una sola mano per
evitare il rischio di scosse derivanti dal
contatto con due superfici a diverso
potenziale elettrico.
La corrente elettrica circolante nei cavi di
alimentazione, del telefono e di segnale è
pericolosa. Per evitare scosse elettriche,
collegare e scollegare i cavi come descritto
quando si effettuano l'installazione, la
rimozione o l'apertura dei coperchi di questo
prodotto o durante il collegamento delle
unità.
Per collegare
Per scollegare
1. SPEGNERE tutti i
dispositivi.
2. Collegare prima tutti i cavi
alle unità.
3. Collegare i cavi di segnale
alle prese.
4. Collegare il(i) cavo(i) di
alimentazione alla presa
elettrica.
5. ACCENDERE le unità.
1. SPEGNERE tutti i
dispositivi.
2. Rimuovere prima il(i) cavo(i)
di alimentazione dalla presa
elettrica.
3. Rimuovere i cavi di segnale
dalle prese.
4. Rimuovere tutti i cavi dalle
unità.
Related service information
241
ATTENZIONE:
Quando si sostituisce la batteria, utilizzare solo una
batteria IBM o batterie dello stesso tipo o di tipo
equivalente consigliate dal produttore. Se il sistema di
cui si dispone è provvisto di un modulo contenente
una batteria al litio, sostituire tale batteria solo con un
tipo di modulo uguale a quello fornito dal produttore.
La batteria contiene litio e può esplodere se utilizzata,
maneggiata o smaltita impropriamente.
Evitare di:
Ÿ
Ÿ
Ÿ
Gettarla o immergerla in acqua
Riscaldarla ad una temperatura superiore ai 100°
C
Cercare di ripararla o smaltirla
Smaltire secondo la normativa in vigore (D.Lgs 22 del
5/2/97) e successive disposizioni nazionali e locali.
ATTENZIONE:
Quando è installata un'unità CD-ROM, notare quanto
segue:
L'utilizzo di controlli, regolazioni o l'esecuzione di
procedure non descritti nel presente manuale possono
provocare l'esposizione a radiazioni pericolose.
L'apertura di un'unità CD-ROM può determinare
l'esposizione a radiazioni laser pericolose. All'interno
dell'unità CD-ROM non vi sono parti su cui effettuare
l'assistenza tecnica. Non rimuovere i coperchi
dell'unità CD-ROM.
PERICOLO
Alcune unità CD-ROM contengono all'interno
un diodo laser di Classe 3A o Classe 3B.
Prestare attenzione a quanto segue:
Aprendo l'unità vengono emesse radiazioni
laser. Non fissare il fascio, non guardarlo
direttamente con strumenti ottici ed evitare
l'esposizione diretta al fascio.
242
Netfinity Server HMM
k32 kg
k55 kg
ATTENZIONE:
Durante il sollevamento della macchina seguire delle
norme di di sicurezza.
ATTENZIONE:
Il pulsante del controllo dell'alimentazione situato nella
parte anteriore del servente non disattiva la corrente
elettrica fornita al servente. Il servente potrebbe anche
avere più di un cavo di alimentazione. Per disattivare
la corrente elettrica del servente, assicurarsi che tutti i
cavi di alimentazione siano scollegati dalla sorgente di
alimentazione.
ATTENZIONE:
Quando sul cavo di alimentazione è installata l'opzione
di sostegno del cavo, il servente deve essere collocato
in prossimità di una presa elettrica facilmente
accessibile.
ATTENZIONE:
Se aperto, lo sportello del servente non supporta il
peso del servente. Per evitare danni alle persone,
assicurarsi di rimuovere o chiudere tale sportello
prima di spostare o sollevare il servente.
Related service information
243
ATTENZIONE:
Non togliere mai il coperchio di un alimentatore o
qualsiasi parte (power backplane e ac box) su cui è
apposta la seguente etichetta.
Tensioni pericolose, corrente e livelli di energia sono
presenti all'interno degli alimentatori, del power
backplane e dell'ac box. All'interno degli alimentatori,
del power backplane e dell'ac box non ci sono parti
soggette a manutenzione. Se si sospetta un problema
in una di queste parti, rivolgersi ad un tecnico di
manutenzione IBM.
ATTENZIONE:
La corrente circolante nei cavi di alimentazione, del
telefono e di segnale è pericolosa. Per evitare
situazioni pericolose per le persone o danneggiamenti
all'apparecchiatura, scollegare i cavi di alimentazione, i
sistemi di telecomunicazioni, le reti e ed i modem
prima di aprire i coperchi del servente se non
diversamente indicato nelle procedure di installazione
e configurazione.
ATTENZIONE:
Il cavo di alimentazione collegato alla ventola
dovrebbe essere scollegato ogni volta che l'assieme
ventola non sia installato nel servente; diversamente la
ventola si potrebbe attivare mentre la si sta
maneggiando e le pale potrebbero provocare ferite le
dita.
>50 kg
ATTENZIONE:
Non poggiare oggetti che pesano più di 50 kg sulla
parte superiore del servente.
244
Netfinity Server HMM
Related service information
245
246
Netfinity Server HMM
Related service information
247
PELIGRO
Para evitar una posible descarga eléctrica, no
conecte ni desconecte los cables ni lleve a
cabo ninguna operación de instalación, de
mantenimiento o de reconfiguración de este
producto durante una tormenta eléctrica.
Para evitar una posible descarga:
Ÿ
El cable de alimentación debe
conectarse a un receptáculo con una
instalación eléctrica correcta y con toma
de tierra.
Ÿ
Los aparatos a los que se conecte este
producto también deben estar
conectados a receptáculos con la debida
instalación eléctrica.
Cuando sea posible, utilice una sola mano
para conectar o desconectar los cables de
señal a fin de evitar una posible descarga al
tocar dos superficies con distinto potencial
eléctrico.
La corriente eléctrica de los cables de
comunicaciones, teléfono y alimentación
puede resultar peligrosa. Para evitar una
posible descarga, siga las indicaciones de
conexión y desconexión de los cables
siempre que tenga que instalar, mover o abrir
las cubiertas de este producto o de los
dispositivos acoplados.
Instrucciones de conexión
1. Apague todos los
componentes (OFF).
2. En primer lugar, conecte
todos los cables a los
dispositivos.
3. Conecte los cables de señal
a los receptáculos.
4. Conecte los cables de
alimentación a las tomas.
5. Encienda el dispositivo
(ON).
248
Netfinity Server HMM
Instrucciones de desconexión
1. Encienda todos los
componentes (ON).
2. En primer lugar, retire los
cables de alimentación de
las tomas.
3. Retire los cables de señal
de los receptáculos.
4. Retire todos los cables de
los dispositivos.
percaución:
Al cambiar la batería, utilice únicamente la batería IBM
Número de pieza 33F8354 o un tipo de batería
equivalente recomendado por el fabricante. Si el
sistema tiene un módulo que contiene una batería de
litio, sustitúyalo únicamente por el mismo tipo de
módulo del mismo fabricante. La batería contiene litio
y puede explotar si no se utiliza, manipula o desecha
correctamente.
Lo que no debe hacer
Ÿ
Ÿ
Ÿ
Tirar o sumergir el producto en agua.
Exponer el producto a una temperatura superior a
100°C.
Reparar o desmontar el producto.
Cuando quiera desechar la batería, siga las
disposiciones y reglamentaciones locales.
percaución:
Cuando instale una unidad de CD-ROM, tenga en
cuenta la siguiente información.
Si se llevan a cabo controles o ajustes o se utilizan
métodos que no se atengan a lo aquí especificado, se
puede producir una exposición peligrosa a las
radiaciones.
Si se retiran las cubiertas de la unidad de CD-ROM, se
puede producir una peligrosa exposición a radiaciones
de láser. Dentro de la unidad de CD-ROM no existen
piezas reparables. No retire las cubiertas de la unidad
de CD-ROM.
PELIGRO
Algunas unidades de CD-ROM tienen
incorporado un diodo de láser de Clase 3A o
de Clase 3B Tenga en cuenta la siguiente
información.
Cuando la unidad está abierta se generan
emisiones de rayos láser. No dirija la mirada
al haz, no lo observe directamente con
instrumentos ópticos y evite la exposición
directa.
Related service information
249
k32 kg
k55 kg
percaución:
Alce la máquina con cuidado; el sobrepeso podría
causar alguna lesión.
percaución:
El botón de control de alimentación del panel frontal
del servido no apaga la corriente eléctrica
suministrada al servidor. Puede sucede que el servidor
tenga más de un cable de alimentación. Para elimiar
por completo la corriente eléctrica del servidor,
asegúrese de desconectar todos los cables de
alimentación del suministro de alimentación.
percaución:
Cuando la opción de soporte del cable de alimentación
está insalada en el cable de alimentación, el servidor
debe estar conectado a un suministro de alimentación
de fácil acceso.
percaución:
Si no está cerrada, la puerta del servidor no soportará
el peso del mismo. A fin de evitar lesiones, antes de
alzar el servidor o cambiarlo de sitio, extraiga la puerta
o ciérrela bien.
250
Netfinity Server HMM
percaución:
No retire nunca la cubierta de una caja de
alimentacion ni de ninguna otra pieza (como el cajetín
de corriente alterna o la placa posterior de
alimentación) que tenga la siguiente etiqueta.
Las cajas de alimentación, las placas posteriores de
suministro y los cajetines de CA contienen niveles
peligrosos de voltaje, de corriente y de energía.
Ninguna de las piezas internas de las cajas de
alimentación, de la placa posterior o del cajetín de CA
son reparables por el usuario. Si detecta algún
problema con alguna de esas piezas, póngase en
contacto con un técnico de IBM.
percaución:
La corriente eléctrica de los cables de
comunicaciones, de teléfono y de alimentación puede
resultar peligrosa. Para evitar posibles lesiones o
daños del aparato, desconecte los cables de
alimentación, los sistemas de telecomunicaciones, las
redes y los módems antes de abrir las cubiertas del
servidor, salvo que se indique lo contrario en las
instrucciones de las operaciones de instalación y
configuración.
percaución:
Si el dispositivo de ventilación no está instalado en el
servidor, debe desconectar el cable de alimentación
que va a parar al ventilador; de lo contrario, podría
empezar a funcionar mientras lo sostiene y las hojas
podrían causarle alguna lesión.
>50 kg
percaución:
No coloque ningún objeto cuyo peso sea superior a
los 50 kilos sobr la bandeja modelo del servidor.
Related service information
251
Laser compliance statement
Some IBM Personal Computer models are equipped from
the factory with a CD-ROM drive. CD-ROM drives are
also sold separately as options. The CD-ROM drive is a
laser product. The CD-ROM drive is certified in the U.S. to
conform to the requirements of the Department of Health
and Human Services 21 Code of Federal Regulations
(DHHS 21 CFR) Subchapter J for Class 1 laser products.
Elsewhere, the drive is certified to conform to the
requirements of the International Electrotechnical
Commission (IEC) 825 and CENELEC EN 60 825 for
Class 1 laser products.
When a CD-ROM drive is installed, note the following.
CAUTION:
Use of controls or adjustments or performance of
procedures other than those specified herein might
result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de
procedimentos diferentes daqueles aqui especificados
pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d'exposition au rayon laser,
respectez les consignes de réglage et d'utilisation des
commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier
festgesetzt verwendet, kann gefährliche
Laserstrahlung auftreten.
L'utilizzo di controlli, regolazioni o l'esecuzione di
procedure diverse da quelle specificate possono
provocare l'esposizione a
252
Netfinity Server HMM
El uso de controles o ajustes o la ejecución de
procedimientos distintos de los aquí especificados
puede provocar la exposición a radiaciones
peligrosas.
Opening the CD-ROM drive could result in exposure to
hazardous laser radiation. There are no serviceable parts
inside the CD-ROM drive. Do not open.
Some CD-ROM drives contain an embedded Class 3A or
Class 3B laser diode. Note the following.
DANGER:
Laser radiation when open. Do not stare into the
beam, do not view directly with optical instruments,
and avoid direct exposure to the beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe
de luz, não olhe diretamente por meio de instrumentos
óticos e evite exposição direta com o feixe de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le
faisceau, de le regarder directement avec des
instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder
über optische Instrumente in den Laserstrahl sehen
und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad
szemmel, se optikai eszközökkel. Kerülje a
sugárnyalábbal való érintkezést !
Aprendo l'unità vengono emesse radiazioni laser. Non
fissare il fascio, non guardarlo direttamente con
strumenti ottici e evitare l'esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine
con instrumental óptico el haz de luz. Evite la
exposición directa al haz.
Related service information
253
Send us your comments!
We want to know your opinion about this manual (part
number 09N1064). Your input will help us to improve our
publications.
Please photocopy this survey, complete it, and then fax it
to IBM HMM Survey at 919-543-8167 (USA).
Name
Phone Number
1. Do you like this manual?
Ø Yes
Ø No
2. What would you like to see added, changed, or
deleted in this manual?
3. What is your service experience level?
Ø Less than five years
Ø More than five years
4. Which Servers do you service most?
Thanks in advance for your response!
254
Netfinity Server HMM
Problem determination tips
Due to the variety of hardware and software combinations
that can be encountered, use the following information to
assist you in problem determination. If possible, have this
information available when requesting assistance from
Service Support and Engineering functions.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Machine type and model
Processor or hard disk upgrades
Failure symptom
– Do diagnostics fail?
– What, when, where, single, or multiple systems?
– Is the failure repeatable?
– Has this configuration ever worked?
– If it has been working, what changes were made
prior to it failing?
– Is this the original reported failure?
Reference/Diagnostics Diskette Version
– Type and version level
Hardware configuration
– Print (print screen) configuration currently in use
– BIOS level
Operating system software
– Type and version level
Important
To eliminate confusion, identical systems are
considered identical only if they:
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the
same locations
4. Have the same address
jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same Reference/Diagnostics Diskette
(version)
7. Have the same configuration options set in the
system
8. Have the same setup for the operation system
control files
Comparing the configuration and software set-up
between “working and non-working” systems will often
lead to problem resolution.
Related service information
255
Phone numbers, U.S. and Canada
Note
EMEA customers should contact their Dealer or IBM
Service organization.
Before you place a call to the Support Center, refer to
“Problem determination tips” on page 255.
Authorized Dealers or Servicers
Number
Information
919-517-0001
800-528-7705
800-937-3737
800-426-2472
Bulletin Board Service - IBM
Bulletin Board Service - TSS Only
IBM Business Partner Education
IBM Customer Engineer Technical
Support
IBM Dealer Support Center
IBM Direct Desktop Software Sales
IBM Part Number ID and Look Up
IBM PC HelpCenter
IBM Software Defect Support (CSDs)
IBM Software Ordering (Publications)
IBM Supplies Technical Hotline
IBM Warranty Parts Claims Center
800-IBM-DEAL
800-342-6672
303-924-4015
800-426-7763
800-237-5511
800-327-5711
800-426-1484
800-388-7080
U.S. Customers and Helpware Subscribers
Number
Information
919-517-0001
800-426-8322
800-999-0052
800-237-4824
800-964-8523
800-742-2493
800-447-4700
800-426-2468
800-426-3333
800-IBM-SERV
800-772-2227
800-426-7282
800-426-9402
(Ext. 150)
800-241-1620
800-342-6672
800-237-5511
800-284-5933
914-962-0310
800-547-1283
Bulletin Board Service - IBM
Customer Education Business Unit
Customized Operational Services
EduQuest (Educational Computers)
End User HelpDesk Support
IBM Anti-Virus Services
IBM Authorized Dealer Referrals
IBM Dealer Referral
IBM Information Referral Service
IBM Service
IBM PC HelpCenter and HelpDesk
IBM Technical Manuals
Multimedia Information Center
800-551-2832
256
Multimedia HelpCenter
OS/2 Information Line
OS/2 Support Services
Prodigy
Prodigy User Questions
Technical Coordinator Program
SystemXtra for Personal Systems
LAN Automated Distribution/2
OS/2 Bulletin Board
OS/2 Application Assistance Center
Technical Solutions Magazine
Netfinity Server HMM
IBM Canada Customer and Servicer Support
Number
Information
800-661-PSMT
905-316-5556
Business Partner Marketing Support
Business Partner Marketing Support Toronto
Business Partner Marketing Support French
Customer Relations
Customer Service Dispatch
Customer Service Parts
Customer Support Center (ISC)
Customer Service Repair Centre
Dealer Support Group (DSG)
HelpClub Registration / IBM Direct
HelpFax
HelpFax - Toronto
HelpPC
IBM Certification Administrator
Mail to: 50 Acadia Drive
Markham, Ontario L3R 0B3
IBM Education (A+ Course)
IBM Information Network Support
IBM PC Service Partners
International Warranty Registration
Lexmark Product Information
PartnerLine
Parts Orders, Exchange or Emergency
Parts Regular Orders, Exchange
514-938-6048
800-465-4YOU
800-IBM-SERV
800-263-2769
800-465-2222
416-443-5701
800-505-1855
800-465-7999
800-465-3299
905-316-3299
800-565-3344
905-513-3355
800-661-2131
800-268-3100
800-387-8343
800-487-7426
800-663-7662
800-IBM-9990
800-263-2769
416-443-5808
(Fax)
416-443-5755
514-938-3022
905-316-4255
604-664-6464
204-934-2735
800-661-7768
800-565-3344
800-387-8483
800-465-1234
905-316-4148
905-316-4100
(Fax)
905-316-4150
905-316-4100
(Fax)
905-316-4872
905-316-4100
(Fax)
800-661-2131
800-565-3344
416-443-5835
(Fax)
905-316-2445
905-316-3515
(Fax)
416-443-5778
800-505-1855
800-267-7472
Parts Orders, Inquiries
PC Co Bulletin Board - Montreal
PC Co Bulletin Board - Markham
PC Co Bulletin Board - Vancouver
PC Co Bulletin Board - Winnepeg
PS Marketing Support (PSMT)
PS/1 Warranty Customer Helpline
PS/1 Warranty Service (DOAs)
Publications Ordering
Service Management Support
Service Management Support
Service (Warranty) Manager
Service (Warranty) Manager
Service Quality Programs
Service Quality Programs
Skill Dynamics (Education)
ThinkPad EasyServe
Warranty Claim Fulfillment
Warranty Claim Reimbursement
Warranty Claim Reimbursement
Warranty Claim Parts Inquiry
Warranty Provider Support Hotline
Warranty Service, ThinkPad
Related service information
257
Trademarks
The following terms are trademarks of the IBM Corporation
in the United States or other countries or both:
Alert on LAN
HelpCenter
HelpFax
Netfinity
PS/1
Skill Dynamics
ThinkPad
EduQuest
HelpClub
IBM
OS/2
PS/2
SystemXtra
Wake on LAN
The following terms are trademarks of other companies:
Notes
Lotus Development Corporation
Pentium and MXX are trademarks or registered trademarks
of Intel Corporation.
Windows and Windows NT are trademarks or registered
trademarks of Microsoft Corporation.
258
Netfinity Server HMM
IBM

Part Number: 09N1064
Printed in U.S.A.
S1ðL-9798-ð4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement