SM8-RC RS232 Controllable Microphone Mixer / Switcher Instructions

SM8-RC RS232 Controllable Microphone Mixer / Switcher Instructions
SM8-RC RS232 Controllable Microphone Mixer / Switcher Instructions
The SM8-RC is a RS232 controllable microphone mixer and switcher for use ETS pre-amplified microphones
only. The SM8-RC is primarily designed to be used in conjunction with DVRs / video gateways in one way
(or two-way: using the companion SS8-RC speaker switcher) to expand versatility in audio zone handling. Notethe DVR manufacturer must write custom software to “talk” to the –RC series switchers via an available RS232
port on the DVR using a simple ASCII protocol described later in this document. Contact ETS technical support
for a list of DVR manufacturers who have integrated the use of the –RC switchers into their platforms.
Note-If your application requires more than 8 audio zones, you must add (loop or cascade) additional SM8-RCs for 8
more zones and up to a maximum of 32 zones total (4 SM8-RCs). Each SM8-RC is assigned an ID number for its range
of zones as described later in this document.
Front panel controls and indicators
When powered up, the SM8-RC is in remote control mode (the front switches do not work.)
If you want to control the switcher manually, press and hold the Zone 1 button until the “Recorder” indicator light goes out.
You can now select and deselect Zones by pressing their respective channel buttons. You can also set the volume of a
zone by adjusting the corresponding Level control.
To go back to RS-232 control mode, press and hold the Zone 1 until the “Recorder” light illuminates.
Setting the zone range ( ID ) for looped SM8-RCs
Unplug the SM8-RC from its AC power Source. Press and HOLD DOWN the corresponding zone number which
translates to ID channel number. CH1=ID1….CH4=ID4. Power up the SM8-RC until the corresponding channel light
illuminates. Then release the switch and the CH lamp will extinguish shortly thereafter.
ID 1= zones 1-8
ID 2= zones 9-16
ID 3= zones 17-24
ID 3= zones 25-32
Note-On a power down / up cycle of the SM8-RC, the ID of the unit will be shown on the corresponding zone lamp (1-4)
for 2 seconds.
Rear panel connections
PWR: The SS8-RC uses a 12Vdc 1amp transformer. Note- the SS8-RC and SM8-RC use different types of AC adapters.
Audio Out Connector: Connect this to the Audio input of your remote monitoring equipment.
Audio In Connector: When using multiple SM8-RCs, connect the Audio output of the first SM8-RC to the Audio input of the next
SM8-RC using the supplied RCA patch cable.
RS-232 Connectors: This is a looping RS-232 input and output. You only need one RS-232 port on your remote monitoring equipment
to control up to 4 SM8-RC and 4 SS8-RC devices. Plug the RS-232 DB9/3.5mm cable into either RS-232 jack on the SM8-RC. Connect
the other end of this cable to your remote monitoring equipment. If using more than 1 SM8-RC, Plug the supplied 3.5mm/3.5mm patch
cord into the remaining jack of the first SM8 and into the next SM8-RC (see connection diagram).
Microphone inputs Use a single pair shielded #22 wire for microphone cable runs up to 1500’. You can connect any SM1 series
microphone to the SM8-RC inputs.
ETS microphone speaker switcher command protocol version 2.0
Note- all selected channel settings are lost during a power outage of an SM8-RC. The –RC series switchers are
also, RS232, listen only devices and currently do not communicate back any information to the host controller.
Therefore, it is recommended that the host control software periodically update the switchers via RS232 with the
current settings as a precaution so as to not lose track of channel settings during a power loss.
Command formats
• All commands received must be RS232, 2400 Baud, 8N1 (8 data bits, No parity and 1 stop bit). • All commands must be ASCII characters and all letters must be upper case. • Each command string must be immediately followed with a <CR> (0D hex) character to mark the end of transmission. DO NOT add a <LF> (0A hex) after <CR>. • All single digit channel addresses must have an ASCII 0 zero preceding them. 00 is not a valid channel number. Example: 01,02,03 • All channels addressed in the “multi channel format” described below must have commas as separators between channel numbers. 01‐99 is the valid range. Example: MI,01,50,99<CR>
• Commands may be combined with the asterisk * (2A hex) command separator character to form a single command transmission string as in the following format Example: MI01*SO01,99*MI02*BO16,32<CR>.
• Each command must be 5 characters minimum in length including the <CR> character. Single combined command strings cannot exceed 48 chars total. • Because there is no report back of switcher channel status to the host computer from the switchers, it is highly recommended that a global command such as BN<CR> preface all switching commands. This way you will always know all channels are off before turning any channels on. Other approaches are valid, but require keeping track of enabled channels in the host software. MICROPHONES (M=Microphone)
Function Command
MICROPHONE “IN” MIxx<CR> (xx=01‐99) 01=1, 02=2, etc. Multi channel format: MI01,99 <CR>
MICROPHONE “OUT” MOxx<CR> (xx=01‐99) 01=1, 02=2, etc. Multi channel format: MO01,99<CR>
MICROPHONE “ALL” MA<CR>
MICROPHONE “NONE” MN<CR>
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ SPEAKERS (S=Speaker)
Function Command
SPEAKER “IN” SIxx<CR> (xx=01‐99) 01=1, 02=2, etc. Multi channel format: SI01,99<CR>
SPEAKER “OUT” SOxx<CR> (xx=01‐99) 01=1, 02=2, etc. Multi channel format: SO01,099<CR>
SPEAKER “ALL” SA<CR>
SPEAKER “NONE” SN<CR>
‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ BOTH MICROPHONES and SPEAKERS (B=both)
Function Command
MIC AND SPEAKER “IN” BIxx<CR> (xx=01‐99) 01=1, 02=2, etc. Multi channel format: BI01,99<CR>
MIC AND SPEAKER “OUT” BOxx<CR> (xx=01‐99) 01=1, 02=2, etc. Multi channel format: BO01,99<CR>
MIC AND SPEAKER “ALL” BA<CR>
MIC AND SPEAKER “NONE” BN<CR>
Warranty
All ETS products carry a one year parts and labor warranty. This warranty does not cover damages as a result of misuse, improper handling of the unit
or exposure to extreme temperatures or moisture. At its discretion, ETS reserves the right to repair or replace this unit under the conditions of the
warranty. If you experience problems with your equipment call ETS at: 505-888-3923 to obtain a return authorization number. Equipment requiring repair
beyond the warranty period or units that have been damaged or are not covered under the warranty can be repaired by ETS for a minimal cost under
most conditions.
Made in the USA
by
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising