Car Multimedia Systems.
VDO Dayton. The Car Brand.
MI 2200
Multimedia Interface
Enables stand-alone use of two VDO Dayton monitors
Automatic and manual source selection
IR Remote Control RCM 5500
Various audio output
Input for up to 4 sources
Integrated power supply for Reversing Camera
Options
In/output connector terminal RST 5400 for interior integration
VDO Dayton Navigation System
Reversing Camera Set RV 5100
Video components (e.g. TV Tuner, DVD Player, Game console)
2nd Remote Control
MI 2200
Multimedia Interface
Automatic Source Selection
Input for up to 4 sources
Based on its source priority logic, MI 2200 can switch different sources
automatically to monitor 1. This monitor shall be used as driver's screen,
when installed in an according system constellation. In this case the
reversing camera has highest priority and will be shown automatically
when the rear gear gets active. Second priority has the navigation system
which is than usually displayed. Only when the car is parked and the navigation system is switched into stand-by mode, one of the AV sources can
get activated. This function is for driver's safety reason.
The MI 2200 provides input for up to 4 different sources.
- 1 VDO Dayton Navigation System (PC 5xxx)1
- 1 VDO Dayton Reversing Camera (RV 5100)
- 2 universal AV sources, such as DVD Player DV 6100 or
TV Tuner TV 5100
Manual Source Selection
Integrated power supply for reversing camera
To make the installation more simple and less costly MI 2200 provides an
integrated power supply for a VDO Dayton Reversing Camera. This is the
most simple and safest way to get the rear view image on the screen.
Monitor 2 - but also monitor 1 - when used in the constellation of a pure
rear seat entertainment system can display always one of the 2 possible to IR Remote Control
connect AV sources2. In this configuration the desired source is selected via The included credit card remote control RCM 5500 enables the indepenthe included IR remote control independently for each monitor.
dent AV source selection for both monitors as well as the pre-adjustment
for each monitor's volume setting. Not selectable via the remote control is
the signal of the reversing camera and the navigation system2.
Various Audio Output
MI 2200 offers audio output to each monitor. Further it includes a
2 channel RCA output to get sound through the car stereo system via it's Status Indicator
auxiliary input. To enable a wired headphone connection, one can utilize This indicator lit up whenever a source is detected and the automatic
RST 5400, VDO Dayton's elegant and easy to install connector terminal3. It signal switching leads through such signal to the monitor.
offers 3.5 mm output for both monitors sound as well as a 2 channel AV
input to allow i.e. the simple connection of a video camera or a game
console.
Important notes
1)
In case a VDO Dayton Navigation System PC 5xxx is
connected, an additional monitor cable might be
required, which is not a part of MI 2200 packing
content. Please check out VDO Dayton's different
monitor cables to find the best matching one fitting
to your requirements.
2)
In case a VDO Dayton Navigation System PC 54xx or
higher is used in combination with a VDO Dayton
monitor MM 55xx or higher, the navigation signal
becomes also available.
3)
RST 5400 is an optional accessory. It offers also PS/2
input which can not be used with MI 2200.
Technical data
06/04, MI 2200, subject to modification
•
•
•
•
•
•
•
Operating voltage: 10.5V - 15.6V, negative ground
Power consumption: typical 2A / 3.2A (1/2 monitors)
Operating temp. range: -20°C to +70°C
Video in/out (AV1/2): 1Vpp / 75 Ohm
Audio in (AV1/2): 2Vpp / 20 kOhm
Audio 1 RCA out: 1.5Vpp / 10 kOhm
Req. headphone impedance: min. 32 Ohm
(for use with RST 5400)3
• Dimensions: 170 x 110 x 44 mm (wxdxh)
• Weight: ca. 350g.
Connections
www.vdodayton.com
Car Multimedia Systems.
VDO Dayton. The Car Brand.
Download PDF