APPROACH SIDE SAFETY SIDE
EAGLE
5 4 3 2 1
24 V
TRANSFORMER
115 VAC
BODYGUARD
DK-12
DATA + 7
DATA - 6
N.C. 5
N.O. 4
COM 3
POWER 2
POWER 1
"B" CONTROL
WHITE
GREEN
RED
90 DEGREE LIMIT SWITCH
CMN 6
* P1 COMMON 5
4
2
N/O
N/C
3
1
N/O
N/C WHITE*
7
24VAC
ISO RELAY
COIL
8
BROWN
ORANGE
RED/WHITE
WHITE
LO21
RESISTOR
RED
BLACK
SOLENOID WIRES TYPICALLY
RED OR BLACK
BLUE
MOTOR
WHITE
OPTION
COM.
N/C
MAGNETIC REED
SWITCH
NOTES: 1) OPTION SAFETY SIDE SUPERSCAN INHIBIT WITH MAGNETIC
REED SWITCH.
2) SWITCH MUST BE ADJUSTED TO OPEN AT APPROXIMATELY
70 DEGREES.
3) LO-21 RED AND BLACK WIRES CONNECT TO THE SOLENOID VALVE.
B.E.A., Inc.
100 Enterprise Drive, Pittsburgh, PA 15275
PH: (412) 249-4100 FAX: (412) 249-4101
TITLE: KM 2000 "B" CONTROL WITH EAGLE,
BODYGUARD, SUPERSCANS, INHIBIT
RELAY
SIZE: CAGE CODE: DWG NO: FILE OF:
A
SCALE:
NONE
80.0111
DATE:
05 JAN 04
ENG'G
DRAWN BY:
JED
SHEET:
1 OF 1
REV:
01
IF USING DRY CONTACT SAFETY BEAM
CONNECT N.O. & COM. TO GRAY & PURPLE
RESPECTIVLEY BROWN
WHITE
+ -
WHITE
GREEN
BROWN
+
24 V
TRANSFORMER
EAGLE
N.C. 5
N.O. 4 green
COM 3 white
POWER 2 black
POWER 1 red
RED +
BLACK OPERATOR
J2
F1
F2
J1
J5
J10
J6
J3
F3
W12
MICRO
CONTROL
SW1
J9
YELLOW
BODYGUARD
DATA + 7 blue
DATA - 6 brown
N.C. 5
N.O. 4 green
COM 3 white
POWER 2 black
POWER 1 red
RED/WHITE
WHITE
RED
GREEN
LO-21K
LO21K DEFAULT DIP SWITCHES
FOR KM
OFF
BLACK -
ON
NOTES: 1) WIRE LO-21 RED / BLACK WIRES TO MICRO-SWITCH WHEN STACK OR LATCH ASSIST FUNCTIONS ARE TURNED
ON. (SEE NOTE 2)
2) AN ADDITIONAL MICROSWITCH WILL NEED INSTALLED ON OPERATOR ORIENTED 180 DEGREES FROM CLOSED
LATCH SPEED SWITCH. THIS WILL PROVIDE PROPER VOLTAGE TO THE LO21K. CONTACT B.E.A. TECHNICAL
SUPPORT FOR WIRING INFORMATION.
3) SW-1 SETTINGS (UP IS OFF) 1.PUSH-N-GO 2. LATCH ASSIST 3. RATCHET FUNCTION 4. STACK PRESSURE.
4) DUAL CONTROL SHOWN
5) SW-1 CALIBRATION SWITCH REMOVE JUMPER AFTER 1ST ACTIVATION AFTER INITIAL POWER UP. STORE ON 1 POST.
100 ENTERPRISE DRIVE
PITTSBURGH, PA 15275
PHONE: (412) 249-4100
FAX: (412) 249-4101
EMAIL: www.beasensors.com
TITLE: KM 3100 "K" CONTROL WITH
COMMANDER SYSTEM
IF AFTER TROUBLESHOOTING A PROBLEM, A SATISFACTORY SOLUTION CANNOT BE ACHIEVED, PLEASE CALL B.E.A., INC.
FOR FURTHER ASSISTANCE DURING EASTERN STANDARD TIME AT 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS,
CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 / MID-WEST: 1-888-308-8843 / WEST COAST: 1-888-419-2564. DO NOT
LEAVE ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING WORKDAY TO CALL B.E.A., LEAVE THE
DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER SACRIFICE THE SAFE OPERATION OF THE
AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM
SIZE: DRAWN BY:
KJG
A
SCALE:
NONE
REV BY:
TUC
DATE:
23 NOV 2005
PART NO:
SHEET
1 OF 1
80.0134.01
BODYGUARD
LEFT APPRCH SIDE SSCAN RIGHT APPRCH SIDE SSCAN LEFT SAFETY SIDE SSCAN RIGHT SAFETY SIDE SSCAN
24 V
TRANSFORMER
HOLD OPEN
OFF
AUTO
SUPERSCAN QUICK
DISCONNECT CABLE
SUPERSCAN QUICK
DISCONNECT CABLE
RED +
BLACK OPERATOR
J2
F1
F2
J1
J5
J6
J10
J3
F3
W12
MICRO
CONTROL
SW1
J9
STALL YELLOW
EAGLE
N.C. 5
N.O. 4 green
COM 3 white
POWER 2 black
POWER 1 red
RED
GREEN
LO21K
BLACK -
GREEN
OFF
BLUE
ON
YELLOW
NOTES: 1 ) SW-1 SETTINGS (UP IS OFF) 1.PUSH-N-GO 2. LATCH ASSIST 3. RATCHET FUNCTION 4. STACK PRESSURE.
2 ) DUAL CONTROL SHOWN
3 ) SW-1 CALIBRATION SWITCH REMOVE JUMPER AFTER 1ST ACTIVATION AFTER INITIAL POWER UP. STORE ON 1 POST.
IF AFTER TROUBLESHOOTING A PROBLEM, A SATISFACTORY SOLUTION CANNOT BE ACHIEVED, PLEASE CALL B.E.A., INC. FOR FURTHER ASSISTANCE DURING EASTERN STANDARD TIME
AT 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS, CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 / MID-WEST: 1-888-308-8843 / WEST COAST: 1-888-419-2564. DO NOT LEAVE
ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING WORKDAY TO CALL B.E.A., LEAVE THE DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER
SACRIFICE THE SAFE OPERATION OF THE AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM
100 ENTERPRISE DRIVE
PITTSBURGH, PA 15275
PHONE: (412) 249-4100
FAX: (412) 249-4101
EMAIL: www.beasensors.com
TITLE: KM 3000/3100 (MICRO) K-CONTROL
LO21K, W/PARALLAX 2 SYSTEM
Q-DISCONNECT ON APPROACH SIDE
SIZE:
B
DRAWN BY:
KJG
SCALE:
NONE
REV BY:
TUC
DATE:
01 DEC 2005
PART NO:
SHEET
1 OF 1
80.0176.02
BODYGUARD
RIGHT APPRCH SIDE SSCAN LEFT SAFETY SIDE SSCAN
24 V
TRANSFORMER
HOLD OPEN
OFF
AUTO
QUICK-DISCONNECT CABLE
RED +
BLACK OPERATOR
J2
F1
F2
J1
J5
J6
J10
J3
F3
W12
MICRO
CONTROL
SW1
J9
STALL YELLOW
EAGLE
N.C. 5
N.O. 4 green
COM 3 white
POWER 2 black
POWER 1 red
RED
GREEN
LO21K
BLACK -
GREEN
OFF
BLUE
ON
YELLOW
NOTES: 1 ) SW-1 SETTINGS (UP IS OFF) 1.PUSH-N-GO 2. LATCH ASSIST 3. RATCHET FUNCTION 4. STACK PRESSURE.
2 ) DUAL CONTROL SHOWN
3 ) SW-1 CALIBRATION SWITCH REMOVE JUMPER AFTER 1ST ACTIVATION AFTER INITIAL POWER UP. STORE ON 1 POST.
IF AFTER TROUBLESHOOTING A PROBLEM, A SATISFACTORY SOLUTION CANNOT BE ACHIEVED, PLEASE CALL B.E.A., INC. FOR FURTHER ASSISTANCE DURING EASTERN STANDARD TIME
AT 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS, CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 / MID-WEST: 1-888-308-8843 / WEST COAST: 1-888-419-2564. DO NOT LEAVE
ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING WORKDAY TO CALL B.E.A., LEAVE THE DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER
SACRIFICE THE SAFE OPERATION OF THE AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM
100 ENTERPRISE DRIVE
PITTSBURGH, PA 15275
PHONE: (412) 249-4100
FAX: (412) 249-4101
EMAIL: www.beasensors.com
TITLE: KM 3000/3100 (MICRO) K-CONTROL
LO21K, W/PARALLAX 1 SYSTEM
Q-DISCONNECT ON APPROACH SIDE
SIZE:
B
DRAWN BY:
KJG
SCALE:
NONE
REV BY:
TUC
DATE:
01 DEC 2005
PART NO:
SHEET
1 OF 1
80.0177.02
BODYGUARD
APPROACH SUPERSCAN SAFTY SUPERSCAN
24 V
TRANSFORMER
EAGLE
N.C. 5
N.O. 4 green
COM 3 white
POWER 2 black
POWER 1 red
HOLD OPEN
OFF
AUTO
QUICK DISCONNECT
CABLE
J2
F1
F2
J1
J5
J6
J10
J3
F3
W12
MICRO
CONTROL
SW1
J9
YELLOW
LO21K
RED
BLACK
RED
GREEN
OFF
ON
DIP SWITCHES
6, 7, 8, NOT USED
+
-
MOTOR
(NOT USED)
100 ENTERPRISE DRIVE
PITTSBURGH, PA 15275
PHONE: (412) 249-4100
FAX: (412) 249-4101
EMAIL: www.beasensors.com
NOTES: 1) SW-1 SETTINGS (UP IS OFF) 1.PUSH-N-GO=(OFF). 2. LATCH ASSIST=(OFF). 3. RATCHET FUNCTION=(OFF).4. STACK
PRESSURE=(OFF).
2) LO21K: DIP SWITCHES 6, 7, 8, NOT USED.
3) SW-1 CALIBRATION SWITCH (LOCATED ON CONTROL) REMOVE JUMPER AFTER 1ST ACTIVATION AFTER INITIAL
POWER UP. STORE ON 1 POST.
IF AFTER TROUBLESHOOTING A PROBLEM, A SATISFACTORY SOLUTION CANNOT BE ACHIEVED, PLEASE CALL B.E.A., INC.
FOR FURTHER ASSISTANCE DURING EASTERN STANDARD TIME AT 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS,
CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 / MID-WEST: 1-888-308-8843 / WEST COAST: 1-888-419-2564. DO NOT
LEAVE ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING WORKDAY TO CALL B.E.A., LEAVE THE
DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER SACRIFICE THE SAFE OPERATION OF THE
AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM
TITLE: KM 3000/3100 (MICRO) K-CONTROL
LO21K, W/PARALLAX 1 SYSTEM
Q-Disconnect on Safety Side
SIZE: DRAWN BY:
TUC
A
SCALE:
NONE
REV BY:
TUC
DATE:
18 OCT 2005
PART NO:
SHEET
1 OF 1
80.0210.01
BODYGUARD
APPROACH SUPERSCAN SAFTY SUPERSCAN
24 V
TRANSFORMER
EAGLE
N.C. 5
N.O. 4 green
COM 3 white
POWER 2 black
POWER 1 red
HOLD OPEN
OFF
AUTO
QUICK DISCONNECT
CABLE
J2
F1
F2
J1
J5
J6
J10
J3
F3
W12
MICRO
CONTROL
SW1
J9
YELLOW
RED
GREEN
LO21K
RED
BLACK
OFF
ON
DIP SWITCHES
6, 7, 8, NOT USED
+
-
MOTOR
(NOT USED)
NOTES: 1) SW-1 SETTINGS (UP IS OFF) 1.PUSH-N-GO(OFF). 2. LATCH ASSIST(OFF). 3. RATCHET FUNCTION(OFF). 4. STACK
PRESSURE(OFF).
2) LO21K: DIP SWITCHES 6, 7, 8, NOT USED.
3) SW-1 CALIBRATION SWITCH REMOVE JUMPER ON CONTROL AFTER 1ST ACTIVATION AFTER INITIAL POWER
UP. STORE ON 1 POST.
IF AFTER TROUBLESHOOTING A PROBLEM, A SATISFACTORY SOLUTION CANNOT BE ACHIEVED, PLEASE CALL B.E.A., INC.
FOR FURTHER ASSISTANCE DURING EASTERN STANDARD TIME AT 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS,
CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 / MID-WEST: 1-888-308-8843 / WEST COAST: 1-888-419-2564. DO NOT
LEAVE ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING WORKDAY TO CALL B.E.A., LEAVE THE
DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER SACRIFICE THE SAFE OPERATION OF THE
AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM
100 ENTERPRISE DRIVE
PITTSBURGH, PA 15275
PHONE: (412) 249-4100
FAX: (412) 249-4101
EMAIL: www.beasensors.com
TITLE: KM 3000/3100 (MICRO) K-CONTROL
LO21K, W/PARALLAX 1 SYSTEM
Q-Disconnect on Approach Side
SIZE: DRAWN BY:
TUC
A
SCALE:
NONE
REV BY:
TUC
DATE:
18 OCT 2005
PART NO:
SHEET
1 OF 1
80.0211.01
LO-LIN X
SWIN G
BESAM 300
BESAM M /P
DOM
GT 300/400
GT M AG
HORTON 4190
HUNTER
KM K
STANLEY "L"
STANLEY M /P
STANLEY 521
TORM AX TDA
GR EEN WH IT E YELLOW B LUE
A C T .
C OM .
SA F .
ST A LL
B R OWN
ST A L C OM .
13
3
12
4
11
9
15, 17
5
16,18
13
YELLOW GREY BLUE PURPLE
BLACK RED WHITE WHITE
6 BLACK 5 RED 4 WHITE 3 VIOLET
2
ACT.
3, 6, 8
RTN
4
SAF. 1
10
SAF. 2
GREY
RED
5 RED
3, 6, 8
RTN
GREEN WHITE
ORANGE YELLOW
2 1, 8
TB4-5
2
TB4-4
1 ,3, 6, 8
RED
RED
7
TB4-8
8 & 9
YELLOW
BLUE
7
TB4-10
7
WHITE
YELLOW
1, 8
TB4-9
1, 3, 6, 8
DC
MOTOR
SEE NOTE #1
+
-
RED
LO-LINX MOTOR HARNESS p/n: 20.5076
RED
EAGLE 1
LO-LINX EAGLE HARNESS p/n: 20.5096
EAGLE 2
SEE NOTE # 4
MTR STALL
LO-LINX
SENSORS AUX
BEAM
TX RX
SWITCH TO CTRL PWR SETUP
SEE NOTE
#2
SEE NOTE # 4
BLACK
RED
24 V
TRANSFORMER
SEE NOTE #3
BODYGUARD (Y) HARNESS
USED FOR DUAL-EGRESS
APPLICATIONS
LO-LINX SWITCH HARNESS p/n: 20.5078
LO-LINX CONTROL
HARNESS p/n: 20.5097
Pre-wired switch assembly
AUTO
RED
BLACK
WHITE
OFF
HOLD OPEN
BROWN KM K CONTROL
SEE NOTE # 4
WHITE
WHITE/COM
BLUE
YELLOW/STALL
YELLOW
RED/SAF
GREEN
GREEN/ACT
LO-LINX SUPERSCAN HARNESS p/n: 70.5071
DOOR MTD SENSOR
APPROACH SIDE
DOOR MTD SENSOR
SAFETY SIDE
DOOR MTD SENSOR
APPROACH SIDE
NOTES:
1. MOTOR CONNECTION IS TIED IN PARALLEL TO EXISTING MOTOR LEADS. NO RESPECT TO PALARITY IS REQUIRED.
2. EXTERNAL SWITCHES ARE REQUIRED IF INHIBIT DESIRED AT SWING SIDE SUPERSCANS, SWITCH OPENS UPON INHIBIT POINT.
3. THE KNOWING ACT SWITCH IS CONNECTED AT THE AUX INPUT AND CAN BE ANY DRY CONTACT DEVICE SUCH AS A PUSHPLATE, CARD READER,
ETC. THE AUX INPUT IS REQUIRED FOR ALL INITIAL ACTIVATION WHEN FUNCTION 'FA' ON THE LO-LINX IS SET TO '01'.
4. THE SECOND BODYGUARD AND EAGLE ARE PRIMARILY USED IN DUAL-EGRESS APPLICATIONS. ENSURE BODYGUARD RELAY VALUE IS SET TO 2.
IF AFTER TROUBLESHOOTING A PROBLEM, A SATISFACTORY SOLUTION CANNOT BE ACHIEVED, PLEASE CALL B.E.A., INC. FOR FURTHER ASSISTANCE
DURING EASTERN STANDARD TIME AT 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS, CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 /
MID-WEST: 1-888-308-8843 / WEST COAST: 1-888-419-2564. DO NOT LEAVE ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING
WORKDAY TO CALL B.E.A., LEAVE THE DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER SACRIFICE THE SAFE OPERATION
OF THE AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM
DOOR MTD SENSOR
SAFETY SIDE
100 ENTERPRISE DRIVE
PITTSBURGH, PA 15275
PHONE: (412) 249-4100
FAX: (412) 249-4101
EMAIL: www.beasensors.com
TITLE: KM "K" CONTROL
LO-LINX SYSTEM
SIZE:
A
DRAWN BY: REV BY:
JED TUC
SCALE:
NONE
DATE:
10/15/2007
PART NO:
80.0286.00
SHEET
1 OF 1
