Front Panel
NVR Quick Setup Guide
>INSTALLATION AND OPERATION (1)
SYSTEM SETUP
£ ¤ ¥ ¦ ¨
1 Power LED
4 Network LED
2 Record LED
5 USB 2.0 Port
§
3 Playback LED
6 IR Remote Sensor
Rear Panel
*4 PoE NVR
§
*8 PoE NVR
£ ¤ ¥ ¦ ¨ © ª « ¬
§
£ ¤ ¥ ¦ ¨ © ª « ¬
*16 PoE NVR
¤ §
£ « ¥ ¦ ¨ © ª ¬
When power is turned on, you will see the initializing screen and it may take up to one minute to complete. After initializing is complete, an Easy Setup screen will appear.
Easy Setup Wizard
An Easy Setup screen will appear. If you don’t want to go through the setup steps at this time click the Exit button and the system will go to the main live screen. When you want to set up the system just click the Easy Setup Menu or Main menu in the right-click mouse menu. If the Easy Setup is finished and returns to the live screen, the auto connected camera image will be displayed on the live screen.
The NVR system will record automatically as regular recording.
* For basic system setup and configuration it is recommended to complete all the setup steps.
IP Camera Registration
You can check the IP camera list and register the desired IP cameras automatically or manually. If the cameras are connected directly to the IP CAM port, the NVR system will register the cameras automatically. If the cameras are connected to the switch/hub, the NVR system will discover the cameras automatically and then you can register the cameras to the NVR by clicking the "Registration".
3
4
1
2
Ip camera input
Network port
Audio out
VGA out
7
8
5
6 eSATA
HDMI
USB 3.0
Sensor/Alarm: I/O
9
10
11
USB 2.0
Power input
Power switch
NVR Quick Setup Guide
>INSTALLATION AND OPERATION (2)
IP Camera Setup
The user can set up the IP camera details: Profile, Resolution,
FPS, Quality, GOP, Motion, Sensor and Audio.
For motion detection and event recording function, the user must select the Motion as ON position.
Quick search: To search quickly for cameras the user must enter the camera ID and Password.
Detail search: In this case the system will automatically check for all camera ID's and passwords and will generally take longer than "Quick Search".
Record Quality Setup
The user must set the recording quality for each camera for both
Normal and Event conditions. The user can set the “Secondary”
Stream for the normal condition and the “Primary” Stream for the event condition. This function allows the user to save the HDD recording size. If you click the Setup Tab, the IP Camera Setup window will be appeared.
Manual add: To manually add an ONVIF compliant camera the user must enter the full IP address.
Ex. “http://xxx.xxx.xx.xx/onvif/device_service”.
In this case, the IP camera must support Onvif.
Quick search: To search quickly for cameras the user must enter the camera ID and Password.
Recording Schedule Setup
Detail search: In this case the system will automatically check for all camera ID's and passwords and will generally take longer than "Quick Search".
IP Camera Setup
1) CH : 1 ~ 4 (or 16): Select channel for schedule recording.
2) SELECT DAY [SUN – SAT, Hol]
The user can set up the IP camera details: Profile, Resolution,
3) TIME: Move the cursor to desired time and press ENTER
FPS, Quality, GOP, Motion, Sensor and Audio.
key to set it highlighted. Press click again to change schedule
For motion detection and event recording function, the user
recording option by color.
select the Motion as ON position.
You can set different recording schedule and type for each camera
(channel) or you can apply current schedule setting to all other cameras by pressing “Apply to All CH” button. Apply To All Channel:
If selected, “Apply to All CH” window will appear. Press OK to apply the setup to all channels. When the recording schedule setup is done, click OK.
Motion / Event Recording Setup
For motion / event recording function, the user selects the Motion as ON position in the IP Camera Setup menu and set the channel
(camera) as Event recording in the Record > Schedule menu.
Then the icons (motion and event icon) will be appeared on the live screen as below.
Record Quality Setup
The user must set the recording quality for each camera for both
Normal and Event conditions. The user can set the “Secondary”
Stream for the normal condition and the “Primary” Stream for the event condition. This function allows the user to save the HDD recording size. If you click the Setup Tab, the IP Camera Setup window will be appeared.
This menu allows you to create your own recording schedule and trigger type. To enable this feature, the schedule recording feature at
Manual add: To manually add an ONVIF compliant camera the user must enter the full IP address.
Ex. “http://xxx.xxx.xx.xx/onvif/device_service”.
In this case, the IP camera must support Onvif.
* The NVR will set the motion area in the full screen. If the user
wants to set the motion only for the specific area, the user should
set up the motion manually by accessing to the IP camera web.
NVR Quick Setup Guide
>INSTALLATION AND OPERATION (4)
Network Connection Setup
You can set up the network connection route and protocol.
GENERAL OPERATION
1) Connection Mode: Sets the network connection mode.
2) Bandwidth: Sets the maximum data flow to be transferred
(Upload speed).
Options will vary depending on the selected connection mode.
3) IP, Gateway, Subnet Mask and DNS
- For Static IP: You can directly input IP address, Gateway, Subnet
Mask and DNS.
- For Dynamic IP: IP Address, Gateway and Subnet Mask are set
automatically.
4) When the connection setup is complete, click <OK>.
After Easy Setup is completed or exited from Easy Setup menu, a live screen will appear.
When the user does not log-in the system and click on any and it will prompt you to the login dialog.
Enter ID and Password by using the virtual keyboard and click OK.
By default, the ID / Password is “admin” / “admin”
Live Menu Description (Right Click Menu)
1) Port (TCP): Initially, 9350-9351 is set.
It increases / decreased by TCP:
2) WebViewer Port: Enter the port number for the Web Viewer.
Initially, it is set to 80.
3) When the port setup is complete, click OK.
UPnP: This function will automatically perform port forwarding to your router. By checking the box, the system will automatically do port forwarding. If your router does not support UPnP, a FAIL message will appear. If the router does support UPnP, then a SUCCESS message will appear. If the Port is already in use message appears, this indicates that particular port is already in use so you must change to a different port.
Screen Mode
PTZ control
Zoom In
Audio On/Off
Freeze
Stop Alarm
Record Start/Stop
Play
Search
Backup
Main Menu
Information
IP Cam INFO
Easy Setup
IP Camera Registration
Shutdown
Hide Launcher
Logout
Select how you would like to view screen
Activate PTZ window to control the PTZ function.
Can zoom in for the desired area.
Select the audio on or off
Freeze Playback or Live scene
Stops the alarm output and the event monitoring.
Starts/stops the manual recording
Plays the search result (for 30sec. 1min, 5min, 10min and all)
Search for recorded data (by time, event, capture, etc)
Backup data via USB drive
Access the main menu.
Display system information
Display you IP camera information
Quickly setup your system.
Search the registered cameras and add the cameras.
Shut down the unit
Hides the launcher screen.
Log out.
NVR Quick Setup Guide
>INSTALLATION AND OPERATION (5)
NVR Web Viewer Connection Live Launcher
In the live mode, the Live Launcher helps you execute commands with one click without entering into main menu. The Live Launcher screen can be hidden. If you move the mouse cursor near to the icon, a word bubble is appeared to show the tooltip.
£ ¤ ¥ ¦ § ¨ ©
1) Scene Mode
4) Search
7) Audio
10) Freeze
2) Resume Play
5) Zoom In
8) Backup
11) Alarm Off
ª « ¬
3) Record
6) Capture
9) Printer
12) Resume Play
Play Launcher
In the playback/search mode, the Play Launcher helps you to execute commands with one click without entering into main menu.
The Play Launcher screen can be hidden. If you move the mouse cursor near to the icon, a word bubble is appeared to show the tooltipPlay Laun
£ ¤ ¥ ¦ § ¨
1) Open your internet browser.
2) Type the NVR’s IP address in your internet browser
(ex: http://192.168.0.30) or click the detected
NVR in the "Smart Manager". You will be directed to screen as above.
3) The default ID / Password: admin / admin.
4) Select the connect mode (Web viewer or Setup)
5) If you select the Web Viewer mode, there will be JAVA initializing stage.
* Before running your Web viewer, JAVA will need to initialize.
If the JAVA is not installed in your PC, please install it first from the CD file or internet web site.
When you connect to your NVR web-viewer, you will see a screen as below.
© ª « ¬
2)
3)
4)
5)
6)
7)
1)
8)
9)
10)
11)
Playbar: Displays the time of recorded data in the selected channel for the past 24 hours
Playback display mode: Allows user to playback of desired mode
Return button: Redirects to Search Menu
Record: Records all channels in Live Mode
Audio: Turns off all sound/ Audio off
Printer: Allows you to Print image either in Live or Playback Mode
Playback control button: Allows user to control playback of desired function
Capture: You can capture video image either in Playback Mode or Live Mode
Protect: You can protect recorded data from HDD overwriting
Backup: Backup your data by using USB Drive or External HDD
Menu expansion button: Open or hide menu buttons
£ ¤ ¥ ¦ § ¨ © ª « ¬ ® ¯
1)
6)
7)
8)
9)
2)
3)
4)
5)
10)
11)
12)
13)
Connect/Disconnect Button: Connect to NVR which is designated in Login pop-up window.
To disconnect or connect to other NVRs please click this button again.
Search Button: You will be able to search for data by calendar search.
Setup Button: Will allow you to setup you own personal NVR configuration
Channel Selection Button: Can choose any channel to display in full screen display mode
Multi Screen Button: Can set display mode in Full, 4CH(or 8CH or 16CH for specific model)
Print Button: You will be able to print selected channel.
Previous Button: to go back to previous channel or split mode channels/multi screen mode.
Next Button: Takes you to the next channel or set of split mode channels/multi screen mode.
Zoom Button: Zoom IN in one channel mode. Select how much and where to Zoom IN.
Resolution Button: select resolution and adjustments in single channel mode.
Record Button: to enable recording on your NVR. Press it again and will disable recording.
PTZ Control Button: Can control your PTZ camera that’s connected to the NVR.
Playback Control Buttons: Rewind, Play, Fast Forward & Stop
