advertisement
LCD Monitor
User Manual
GL950A / GL950AM
G950A / G950AM
GL951A / GL951AM / G951A
G955A
GL2055A / GL2055 / GL2055M
GL2250 / GL2250M / GL2250HM / GL2250TM
G2250 / G2250HM
GW2250 / GW2250M / GW2250HM
G2255A / G2255
G2251M / G2251TM
GL2450 / GL2450M / GL2450HM
G2450 / G2450HM
GW2450 / GW2450M / GW2450HM
GL2750HM / G2750 / G2750HM / GW2750HM
Downloaded from ManualMonitor.com Manuals
Copyright
Copyright 2012 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ
Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of
BenQ Corporation to notify any person of such revision or changes.
Please follow these safety instructions for best performance, and long life for your monitor.
Power Safety
• The AC plug isolates this equipment from the AC supply.
• The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet should be installed near the equipment and be easily accessible.
• This product should be operated from the type of power indicated on the marked label. If you are not sure of the type of power available, consult your dealer or local power company.
• An approved power cord greater or equal to H03VV-F or H05VV-F, 2G or 3G, 0.75mm2 must be used.
Care And Cleaning
• Cleaning. Always unplug your monitor from the wall outlet before cleaning. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any liquid, aerosol or glass cleaners.
• Slots and openings on the back or top of the cabinet are for ventilation. They must not be blocked or covered. Your monitor should never be placed near or over a radiator or heat source, or in a built-in installation unless proper ventilation is provided.
• Never push objects or spill liquid of any kind into this product.
Servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages or other risks. If any of the above mentioned misuse or other accident such as dropping or mishandling occurs, contact qualified service personnel for servicing.
2
Downloaded from ManualMonitor.com Manuals
BenQ ecoFACTS
BenQ has been dedicated to the design and development of greener product as part of its aspiration to realize the ideal of the "Bringing Enjoyment 'N Quality to Life" corporate vision with the ultimate goal to achieve a low-carbon society. Besides meeting international regulatory requirement and standards pertaining to environmental management, BenQ has spared no efforts in pushing our initiatives further to incorporate life cycle design in the aspects of material selection, manufacturing, packaging, transportation, using and disposal of the products.
BenQ ecoFACTS label lists key eco-friendly design highlights of each product, hoping to ensure that consumers make informed green choices at purchase. Check out BenQ's CSR Website at http://csr.BenQ.com/ for more details on BenQ's environmental commitments and achievements.
For
GL950A / GL950AM / GL951A / GL951AM /
GL2055A / GL2055 / GL2055M / GL2250 /
GL2250M / GL2250HM / GL2250TM /
GW2250 / GW2250M / GW2250HM /
GL2450 / GL2450M / GL2450HM / GW2450 /
GW2450M / GW2450HM / GL2750HM /
GW2750HM
For
G950A / G950AM / G951A / G955A /
G2250 / G2250HM / G2255A / G2255 /
G2251M / G2251TM / G2450 / G2450HM /
G2750 / G2750HM
Downloaded from ManualMonitor.com Manuals
3
Table of Contents
Appendix: Assembling your monitor with a height adjustment stand (HAS) ............ 37
4
Downloaded from ManualMonitor.com Manuals
Getting started
When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement.
BenQ LCD Monitor
Monitor Stand
(for models without height adjustment stand)
Monitor Base
(for models without height adjustment stand)
Monitor Base
(for models with height adjustment stand)
Quick Start Guide
CD-ROM
Power Cord
(Picture may differ from product supplied for your region.)
Downloaded from ManualMonitor.com Manuals
Getting started 5
Video Cable: D-Sub
Video Cable: DVI-D
(Optional accessory for models with DVI inputs, sold separately)
Video Cable: HDMI
(Optional accessory for models with HDMI inputs, sold separately)
Audio Cable
(Optional accessory for models with speakers)
Consider keeping the box and packaging in storage for use in the future when you may need to transport the monitor. The fitted foam packing is ideal for protecting the monitor during transport.
Always keep the product and accessories out of reach of small children.
6 Getting started
Downloaded from ManualMonitor.com Manuals
Getting to know your monitor
Front view
1
2
1. Control buttons
2. Power button
Back view
3 3
4
5
• Above diagram may vary depending on the model.
• Picture may differ from product supplied for your region.
3. Speakers (for models with speakers)
4. Input and output ports (vary by model, see
Input and output ports on page 8
)
5. Kensington lock slot
Getting to know your monitor 7
Downloaded from ManualMonitor.com Manuals
Input and output ports
Available input and output ports may vary depending on your purchased model.
Models with HDMI inputs 1. AC power input jack
2. Audio Line In
1 2 3 4 5 6
Models with dual inputs and speakers
3. Headphone jack
4. HDMI socket
5. DVI-D socket
6. D-Sub socket
1 2 3 5 6
Models with analog-only inputs and speakers
1 2 3
Models with dual inputs
6
1 5 6
Models with analog-only inputs
1 6
8 Getting to know your monitor
Downloaded from ManualMonitor.com Manuals
How to assemble your monitor hardware
• If your model came with a height adjustment stand (HAS), refer to
• If the computer is turned on you must turn it off before continuing.
Do not plug-in or turn-on the power to the monitor until instructed to do so.
• The following illustrations are for your reference only. Available input and output jacks may vary depending on the purchased model.
1. Attach the monitor base.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like the monitor packaging bag on the desk for padding.
Gently lay the screen face down on a flat clean padded surface.
Attach the monitor stand to the monitor base as illustrated until it locks in place.
Gently attempt to pull them back apart to check that they have properly engaged.
Orient and align the stand arm with the monitor, then push them together until they click and lock into place.
Downloaded from ManualMonitor.com Manuals
How to assemble your monitor hardware 9
If the screen size is 27 inches, follow the illustrations on the right to attach the monitor stand and the base.
2
1
4
5
3
Gently attempt to pull them back apart to check that they have properly engaged.
You should position the monitor and angle the screen to minimize unwanted reflections from other light sources.
-5
O
~ +15
O
10 How to assemble your monitor hardware
Downloaded from ManualMonitor.com Manuals
2. Connect the video cable
Do not use both DVI-D cable and D-Sub cable on the same
PC. The only case in which both cables can be used is if they are connected to two different PCs with appropriate video systems. (Not available for analog-only models).
To Connect the D-Sub Cable
Connect the plug of the D-Sub cable (at the end without the ferrite filter) to the monitor video socket.
Connect the other end of the cable (at the end with the ferrite filter) to the computer video socket.
Tighten all finger screws to prevent the plugs from accidently falling out during use.
To Connect the DVI-D Cable
Connect the plug of the DVI-D cable (at the end without the ferrite filter) to the monitor video socket. Connect the other end of the cable (at the end with the ferrite filter) to the computer video socket.
Tighten all finger screws to prevent the plugs from accidently falling out during use.
To Connect the HDMI Cable
Connect the plug of the HDMI cable to one of the two
HDMI ports on the monitor. Connect the other end of the cable to the HDMI port of a digital output device.
If there is more than one video transmission method available to you, you might want to take the picture quality of each video cable into consideration before making the connection.
- Better quality: HDMI / DVI-D
- Good quality: D-Sub
The video cables included in your package and the socket illustrations on the right may vary depending on the product supplied for your region.
3. Connect the audio cable (for models with speakers).
Connect the audio cable between the socket on the rear of the monitor (Line In) and your computer audio outlet.
Either
Or
Or
How to assemble your monitor hardware 11
Downloaded from ManualMonitor.com Manuals
You may connect headphones to the headphone jack found next to the Line In jack of the monitor.
Location of the Line In and headphone jacks may vary by model. Check
Input and output ports on page 8 for details.
4. Connect the power cable to the monitor.
Plug one end of the power cord into the socket labelled
on the rear of the monitor. Do not connect the other end to a power outlet just yet.
5. Connect-to and turn-on the power.
Plug the other end of the power cord into a power outlet and turn it on.
Picture may differ from product supplied for your region.
Turn on the monitor by pressing the power button on the right of the monitor.
Turn on the computer too, and follow the instructions
in Getting the most from your BenQ monitor on page
15 to install the monitor software.
To extend the service life of the product, we recommend that you use your computer's power management function.
12 How to assemble your monitor hardware
Downloaded from ManualMonitor.com Manuals
How to detach the base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like a towel on the desk for padding, before laying the screen face down on a flat clean padded surface.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
2. Push the locking clips upward to detach the monitor base from the monitor stand arm.
While pushing the locking clips upward, detach the stand base from the stand arm.
3. Remove the monitor stand.
Insert a pointed object such as a screwdriver to the hole above the monitor stand arm, and then push the screwdriver against the release button inside the hole.
Then pull the monitor stand backward away from the monitor.
If the screen size is 27 inches, follow the illustration on the right to detach the monitor base.
1
1
2
1
2
3
2
How to assemble your monitor hardware 13
Downloaded from ManualMonitor.com Manuals
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, please read the precautions carefully.
Precautions:
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor base.
Lay the screen face down on a clean and well-padded surface.
Detach the monitor base as instructed in
How to detach the base on page 13
.
If the screen size is 27 inches, follow the illustration on the right to detach the monitor stand.
In case you intend to use your monitor on the stand in the future, please keep the monitor base, monitor stand, and screws somewhere safe for future use.
2. Follow the instruction manuals of the wall mount bracket you purchased to complete the installation.
1
2
1
2
14 How to assemble your monitor hardware
Downloaded from ManualMonitor.com Manuals
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ LCD monitor, you should install the custom
BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will determine which process you need to follow to successfully install the BenQ LCD Monitor driver software. These circumstances relate to which version of Microsoft Windows you are using, and whether you are connecting the monitor and installing the software onto a new computer (without existing monitor driver software), or whether you are upgrading an existing installation (which already has existing monitor driver software) with a newer monitor.
In either case however, the very next time you turn on your computer (after connecting the monitor to your computer), Windows will automatically recognize the new (or different) hardware, and will launch its
Found New Hardware wizard
.
Follow the wizard instructions until it asks you to select a monitor model. At that point, click the
Have Disk
button, insert the BenQ LCD Monitor CD-ROM and select the appropriate monitor model. Further details and step-by-step instructions for either an automatic (new) or upgrade (existing) installation , see:
•
How to install the monitor on a new computer on page 16 .
•
How to upgrade the monitor on an existing computer on page 18
.
• If you require a User Name and Password to login to your Windows computer, you must be logged on as an
Administrator or as a member of the Administrators group in order to install the monitor driver software.
Furthermore, if your computer is connected to a network which has security access requirements, network policy settings may prevent you from installing software on your computer.
• To check the name of the purchased model, refer to the specification label on the back of the monitor.
Downloaded from ManualMonitor.com Manuals
Getting the most from your BenQ monitor 15
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver software on a new computer which has never had a monitor driver installed before. This instruction is only suitable for a computer which has never been used before, and for which the
BenQ LCD Monitor is the first ever monitor to be connected to it.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor connected to it (and has monitor driver software installed), you should not be following these instructions. You should instead be following the instructions for How to upgrade the monitor on an existing computer.
1. Follow the instructions in
How to assemble your monitor hardware on page 9
.
When Windows starts, it will automatically detect the new monitor and launch the Found New
Hardware Wizard
. Follow the prompts until it displays the option to Install Hardware Device
Drivers
.
2. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3. Check
Search for a suitable driver for my device
option, and click
Next
.
4. Check the option for CD-ROM drives (uncheck all others) and click
Next
.
5. Look to confirm that the wizard has selected the correct name of your monitor and click
Next
.
6. Click
Finish
.
7. Restart the computer.
To find the suitable driver files for the purchased model, refer to the following table.
Driver files
GL950A
G950A
GL951A
G951A
G955A
GL2055
GL2250
GL2250H
G2250
G2250H
GW2250
GW2250H
G2251
G2255A
G2255
GL2450
Suitable models
GL950A / GL950AM
G950A / G950AM
GL951A / GL951AM
G951A
G955A
GL2055 / GL2055M / GL2055A
GL2250 / GL2250M / GL2250TM
GL2250HM
G2250
G2250HM
GW2250 / GW2250M
GW2250HM
G2251M / G2251TM
G2255A
G2255
GL2450 / GL2450M
16 Getting the most from your BenQ monitor
Downloaded from ManualMonitor.com Manuals
Driver files
GL2450H
G2450
G2450H
GW2450
GW2450H
GL2750H
G2750
G2750H
GW2750H
Suitable models
GL2450HM
G2450
G2450HM
GW2450 / GW2450M
GW2450HM
GL2750HM
G2750
G2750HM
GW2750HM
Downloaded from ManualMonitor.com Manuals
Getting the most from your BenQ monitor 17
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver software on your Microsoft Windows computer. It is currently tested as compatible for
Windows Vista and Windows 7 Operating System (OS).
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems.
Installing monitor driver software involves selecting an appropriate information file (.inf) on the
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and letting Windows install the corresponding driver files from the CD. You need only steer it in the right direction. Windows has an Upgrade Device Driver Wizard to automate the task and guide you through the file selection and installation process.
See:
• How to install on Windows 7 system on page 19 .
• How to install on Windows Vista systems on page 20
.
18 Getting the most from your BenQ monitor
Downloaded from ManualMonitor.com Manuals
How to install on Windows 7 system
1. Open
Display Properties
.
Go to Start, Control Panel, Hardware and Sound, Devices and Printers and right-click the name of your monitor from the menu.
Alternatively, right-click the desktop and select Personalize, Display, Devices and Printers, and right-click the name of your monitor from the menu.
2. Select
Properties
from the menu.
3. Click the
Hardware
tab.
4. Click
Generic PnP Monitor
, and then the
Properties
button.
5. Click the
Driver
tab and the
Update Driver
button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the
Update Driver Software
window, select the option
Browse my computer for driver software
.
8. Click
Browse
and navigate to the following directory: d:\BenQ_LCD\Driver\ (where d is the drive letter designator for the CD-ROM drive).
The drive letter for your CD drive may differ from the example above depending upon your system - it may be
'D:' or 'E:' or 'F:' etc.
9. Select the correct folder name of your monitor from provided driver list, and click
Next
.
This will copy and install the appropriate monitor driver files to your computer.
10. Click
Close
.
You may be prompted to restart your computer after the driver update is complete.
Downloaded from ManualMonitor.com Manuals
Getting the most from your BenQ monitor 19
How to install on Windows Vista systems
1. Open
Display Settings
.
Right-click the desktop and select Personalize from the popup menu.
Select Display Settings from the Personalize appearance and sounds window.
The Display Settings window will display.
2. Click the
Advanced Settings
button.
The Generic PnP Monitor Properties window will display.
3. Click the
Monitor
tab and the
Properties
button.
4. Click
Continue
in the prompted
User Account Control
window.
5. Click the
Driver
tab and the
Update Driver
button.
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
7. In the
Update Driver Software
window, select the option
Browse my computer for driver software
.
8. Click
Browse
and navigate to the following directory: d:\BenQ_LCD\Driver\ (where d is the drive letter designator for the CD-ROM drive).
The drive letter for your CD drive may differ from the example above depending upon your system – it may be
‘D:’ or ‘E:’ or ‘F:’ etc.
9. Select the correct folder name of your monitor from provided driver list, and click
Next
.
This will copy and install the appropriate monitor driver files to your computer.
10. Click
Close
.
You may be prompted to restart your computer after the driver update is complete.
20 Getting the most from your BenQ monitor
Downloaded from ManualMonitor.com Manuals
Picture optimization
The easiest way to obtain an optimal display from an analog (D-Sub) input is to use the
AUTO
key function. Press the
AUTO
key to optimize the currently displayed image to the screen.
When you connect a digital video output using a digital (DVI or HDMI) cable to your monitor, the AUTO key and the Auto Adjustment function will be disabled, because the monitor will automatically display the best image.
Please ensure that the connected graphic card on your computer is set to the native resolution of the monitor when you use the AUTO key function.
If you wish, you can always adjust the screen geometric settings manually using geometry menu items. To assist you in this endeavour, BenQ has provided a screen test image utility which you can use to check for screen color, grayscale and line gradient display.
1. Run the test program auto.exe from CD-ROM. You could also use any other image, such as the desktop of your operating system. However, we recommend that you use auto.exe. As you run auto.exe, a test pattern displays.
2. Press the
AUTO
key on the monitor.
3. Press the
MENU
key to access the monitor On-Screen Display (OSD) menu.
4. Use the or keys to select
DISPLAY
and press the
ENTER
key to enter the menu.
5. If you notice a vertical noise (like a curtain effect-shimmering of vertical lines), press the
or keys to select
Pixel Clock
and press the
ENTER
key. Then press the or keys to adjust the monitor until the noise disappears.
6. If you notice a horizontal noise, press the or keys to select
Phase
and press the
ENTER
key. Then press the or keys to adjust the monitor until the noise disappears.
Downloaded from ManualMonitor.com Manuals
Picture optimization 21
How to adjust your monitor
The control panel
For models without speakers
4
5
6
1
2
3
For models with speakers
4
5
6
1
2
3
1.
AUTO
: Adjusts vertical position, phase, horizontal position and pixel clock automatically.
2.
MENU
key: Activates OSD main menu and return to the previous menu or exit OSD.
3. /
Display Mode
key (for models without speakers): For Up/Increase adjustment. The key is the hot key for Display Mode.
/
Volume
key (for models with speakers): For Up/Increase adjustment. The key is the hot key for Volume.
4. /
Mode
key: For Down/Decrease adjustment. The key is the hot key for Mode.
5.
ENTER
key: Enters sub menus and select items. For models with DVI inputs, this key is also the hot key for Input.
6.
Power
: Turns the power on or off.
OSD = On Screen Display.
The hot keys will display a graduated scale for adjusting the value of that setting, and will only operate while the
OSD menu is not currently displaying. Hot key displays will disappear after a few seconds of no key activity. See
22 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Hot key mode
The monitor keys perform as hot keys to provide direct access to particular functions whenever the menu isn't currently displaying on-screen.
Display Mode hot key (for models without speakers)
Press the key continually to switch between
Full
and
Aspect
. The setting will take effect immediately.
See also Display Mode on page 30
.
Volume hot key (for models with speakers)
Press the key to display the
Volume
indicators. Further press the key will increase the volume, while the key will decrease the volume.
To Mute, press the Volume hot key for 3 seconds. To release Mute, press the
Volume hot key for 3 more seconds.
Mode hot key
Press the key continually to switch between the 6 modes for the main window, including
Standard
,
Movie
,
Game
,
Photo
,
sRGB,
and
Eco
. The setting will take effect immediately.
See also
.
Input hot key (not available for analog-only models)
Press the
ENTER
key to toggle between different PC video signal inputs that may be connected to your monitor.
The setting will take effect immediately.
See also
How to adjust your monitor 23
Downloaded from ManualMonitor.com Manuals
Main menu mode
You can use the OSD (On Screen Display) menu to adjust all the settings on your monitor.
Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out.
Press the
MENU
key to display the following main OSD menu.
Depending on your purchased model, different OSD menus are available.
1 2 3 4 5
DISPLAY
Auto Adjustment
H. Position
V. Position
Pixel Clock
Phase
Move
10
12
1
12
ENTER Select
MODE: Standard
MENU
Exit
1. Display
2. Picture
3. Picture Advanced
4. Audio (for models with speakers)
5. System
Use the (up) or (down) keys to highlight a menu item, and press the
ENTER
key to enter the Menu item settings.
The OSD menu languages may differ from the product supplied to your region, see “
“OSD Settings” for more details.
For more information on each menu, please refer to the following pages:
• Picture Advanced menu on page 29
24 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Display menu
Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out.
DISPLAY
Auto Adjustment
H. Position
V. Position
Pixel Clock
Phase
Item
Auto
Adjustment
Move
10
12
1
12
ENTER
Select
MODE: Standard
MENU Exit
1. Press the
MENU
key to display the main menu.
2. Press the or keys to select
DISPLAY
and then press the
ENTER
key to enter the menu.
3. Press the or keys to move the highlight to a menu item and then press the
ENTER
key to select that item.
4. Press the or keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU
button.
Range Function Operation
Optimizes and adjusts the screen settings automatically for you. The
AUTO
key is a ‘hot key’ for this function.
Press the
ENTER
key to select this option and make adjustment.
When you connect a digital video output using a digital (DVI or
HDMI) cable to your monitor, the AUTO key and the
Auto
Adjustment
function will be disabled.
H. Position Adjusts the horizontal position of the screen image.
V. Position Adjusts the vertical position of the screen image.
Pixel Clock Adjusts the pixel clock frequency timing to synchronize with the analog input video signal.
Not applicable to a digital input signal.
Press the or keys to adjust the value.
See also: Picture optimization on page 21
.
0 to 100
0 to 100
0 to 100
How to adjust your monitor 25
Downloaded from ManualMonitor.com Manuals
Item
Phase
Function
Adjusts the pixel clock phase timing to synchronize with the analog input video signal.
Not applicable to a digital input signal.
Operation
Press the or keys to adjust the value.
See also:
Picture optimization on page 21 .
Range
0 to 63
26 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Picture menu
Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out.
PICTURE
Brightness
Contrast
Sharpness
Gamma
Color
AMA
Item
Brightness
Contrast
Sharpness
Gamma
Move
12
10
1
ENTER
Select
MODE: Standard
3
ON
MENU
Back
1. Press the
MENU
key to display the main menu.
2. Press the or keys to select
PICTURE
and then press the
ENTER
key to enter the menu.
3. Press the or keys to move the highlight to a menu item and then press the
ENTER
key to select that item.
4. Press the or keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU
button.
Function Operation Range
Adjusts the balance between light and dark shades.
Press the key to increase the brightness and press the
key to decrease the brightness.
Press the key to increase the gamma value (tone becomes darker) and press the key to decrease the gamma value (tone becomes lighter).
0 to 100
Adjusts the degree of difference between darkness and lightness.
Adjusts the clarity and visibility of the edges of the subjects in the image.
Press the key to increase the contrast and press the key to decrease the contrast.
0 to 100
Press the key to improve the crispness of the display and press the key to have softness effect on the display.
1 to 5
Adjusts the tone luminance.
The default value is 3 (the standard value for
Windows).
1~ 5
How to adjust your monitor 27
Downloaded from ManualMonitor.com Manuals
Item Function Operation Range
Color
- Press
ENTER
to enter the Color menu.
Color
Temperature
Normal: Allows video and still photographs to be viewed with natural coloring.
This is the factory default color.
Press the or select this option.
keys to
Bluish: Applies a cool tint to the image and is factory pre-set to the PC industry standard white color.
Reddish: Applies a warm tint to the image and is factory pre-set to the news print standard white color.
Red
Green
Blue
Hue
Saturation
User Mode: The blend of the
Red, Green and Blue primary colors can be altered to change the color tint of the image. Go to the succeeding
Red
,
Green
, and
Blue
menus to change the settings.
Tailors the image color tint.
Decreasing one or more of the colors will reduce their respective influence on the color tint of the image. (e.g. if you reduce the Blue level the image will gradually take on a yellowish tint. If you reduce Green, the image will become a magenta tint.)
Adjusts the degree of how we perceive colors.
Press the or keys and the
ENTER
key to select
Red
,
Green
, or
Blue
. Then use the
or keys to make the color adjustments.
Press the or keys to adjust the value.
Press the or keys to adjust the value.
0 to 100
0 to 100
Adjusts the purity degree of colors.
Press the or adjust the value.
keys to
0 to 100
Reset Color Resets the custom color settings to the factory defaults.
Press
MENU
to leave the Color menu.
AMA (for models with
HDMI inputs)
Improves the gray level response time of the LCD panel.
Press the or change the settings.
Press the or change the settings.
keys to
keys to
• YES
• NO
• ON
• OFF
28 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Picture Advanced menu
Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out.
PICTURE ADVANCED
MODE: Standard
Picture Mode
Senseye Demo
Dynamic Contrast
Display Mode
Color Format
HDMI RGB PC Range
Move
ENTER
5
Standard
OFF
YUV
RGB (16~235)
Select
MENU
Exit
1. Press the
MENU
key to display the main menu.
2. Press the or keys to select
PICTURE ADVANCED
and then press the ENTER key to enter the menu.
3. Press the or keys to move the highlight to a menu item and then press the
ENTER
key to select that item.
4. Press the or keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU
button.
Item
Picture
Mode
Function
Selects a picture mode that best suits the type of images shown on the screen.
• Standard - for basic PC application.
• Movie - for viewing videos.
• Game - for playing video games.
• Photo - for viewing still images.
• sRGB - for better color matching representation with the peripheral devices, such as printers, DSCs, etc.
• Eco - for saving electricity with low power consumption by providing minimum brightness for all running programs.
Operation Range
Press the or keys to change the settings.
• Standard
• Movie
• Game
• Photo
• sRGB
• Eco
How to adjust your monitor 29
Downloaded from ManualMonitor.com Manuals
Item
Senseye
Demo
Dynamic
Contrast
Display
Mode
Function Operation Range
Displays the preview of screen images under the selected mode from Picture
Mode. The screen will be divided into two windows; the left window demonstrates images of Standard mode, while the right window presents the images under the specified mode.
The function is to automatically detect the distribution of an input visual signal, and then to create the optimal contrast.
Press the or keys to change the settings.
Press the
ENTER
key to select this option. Press the
or keys to change the settings.
This feature is provided to allow aspect ratios other than
16:9 or 16:10 (depending on the purchased model) to be displayed without geometric distortion.
• Overscan - Slightly enlarges the input image. Use this feature to hide annoying edge noise if present around your image.
• Full - Scales the input image to fill the screen. Ideal for
16:9 or 16:10 (depending on the purchased model) aspect images.
• Aspect - The input image is displayed without geometric distortion filling as much of the display as possible.
Depending on the purchased model, 16:9 or
16:10 images will fill the screen horizontally while 4:3 or 5:4 images will fill the screen vertically.
Press the or change the settings.
keys to
The options under Display
Mode
will be different depending on the input signal sources.
• ON
• OFF
0 to 5
• Overscan
• Full
• Aspect
To find out the monitor aspect ratio of the purchased model, please check the Specification document on the provided
CD.
30 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Item
Color
Format
HDMI RGB
PC Range
(for models with HDMI inputs)
Function
Determines the color space
(RGB or YUV) based on the following detected video signal:
• D-Sub (VGA) from PC: The default Color Format is
RGB.
• D-Sub (Component) from a video device: The default
Color Format is YUV.
Operation
Press the
ENTER
key to select this option. Press the
or keys to change the settings.
• RGB
• YUV
Range
You might need to manually set the Color Format if colors shown on the monitor screen do not display properly.
• DVI (for models with DVI inputs): Color Format is automatically set to RGB.
• HDMI (for models with
HDMI inputs): Color
Format is not selectable. In other words, Color Format is automatically set depending on the input video source.
Determines the range of color scales. Select an option that matches the RGB range setting on the connected
HDMI device.
Press the
ENTER
key to select this option. Press the
or keys to change the settings.
• RGB (0 ~ 255)
• RGB (16 ~
235)
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 31
Audio menu
Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out.
AUDIO
Volume
Mute
Audio Select
10
MODE: Standard
OFF
Auto Detect
Move
ENTER
Select
MENU
Exit
1. Press the
MENU
key to display the main menu.
2. Press the or keys to select
AUDIO
and then press the
ENTER
key to enter the menu.
3. Press the or keys to move the highlight to a menu item and then press the
ENTER
key to select that item.
4. Press the or keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU
button.
Item
Volume
Mute
Function
Adjusts the audio volume
Mutes the audio input
Audio Select
(for models with HDMI inputs)
Allow users to select the audio source or let the monitor detect it automatically
Operation Range
Press the key to increase the volume and press the key to decrease the volume.
0 ~ 100
Press the or keys to change the settings.
• ON
• OFF
Press the or keys to change the settings.
• Auto Detect
• PC Audio
• HDMI Audio
32 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
System menu
Available menu options may vary depending on the input sources, functions and settings. Menu options that are not available will become grayed out.
SYSTEM
Input
OSD Settings
DDC/CI
HDMI Auto Switch
Auto Power off
Information
Reset All
Move
ENTER
Select
MODE: Standard
D-sub
OFF
OFF
MENU
Exit
1. Press the
MENU
key to display the main menu.
2. Press the or keys to select
SYSTEM
and then press the
ENTER
key to enter the menu.
3. Press the or keys to move the highlight to a menu item and then press the
ENTER
key to select that item.
4. Press the or keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU
button.
Input
Item Function
Use this to change the input to that appropriate to your video cable connection type.
Analog-only models do not have the Input function.
Operation
Press the or keys to change the settings.
Range
• DVI
• D-sub (VGA)
• HDMI (for models with
HDMI inputs)
OSD Settings
- Press
ENTER
to enter the
OSD Settings
menu.
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 33
Item Function Operation Range
Language
H. Position
Sets the OSD menu language. Press the or keys
Adjusts the horizontal position of the OSD menu. to change the settings.
The language options displayed on your OSD may differ from those shown on the right, depending on the product supplied in your region.
Press the or keys to change the settings.
• English
• French
• German
• Italian
• Spanish
• Polish
• Japanese
• Czech
• Traditional
Chinese
• Hungarian
• Simplified
Chinese
• Serbo-Croatian
• Romanian
• Dutch
• Russian
• Swedish
• Portuguese
0 to 100
V. Position Adjusts the vertical position of the OSD menu.
Display Time Adjusts the display time of the
OSD menu.
0 to 100
• 5 Sec.
• 10 Sec.
• 15 Sec.
• 20 Sec.
• 25 Sec.
• 30 Sec.
34 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Item Function Operation Range
OSD Lock
HDMI Auto
Switch
(for models with HDMI inputs)
Auto Power off
Prevents all the monitor settings from being accidentally changed. When this function is activated, the
OSD controls and hotkey operations will be disabled.
To unlock the OSD controls when the OSD is preset to be locked, press and hold the MENU key for 15 seconds to enter the OSD Lock option and make changes.
Alternatively, you may use the or keys to select
NO
in the OSD Lock submenu from the OSD
Settings
menu, and all
OSD controls will be accessible.
Press
MENU
to leave the
OSD Settings
menu.
DDC/CI* Allows the monitor settings to be set through the software on the PC.
Press the
ENTER
key to select this option. Press the or keys to change the settings.
When this function is activated, HDMI port will be in the input auto select loop.
Otherwise, HDMI can only be selected by input select or by hot key.
Press the to change the settings.
Press the the
or
ENTER
or
keys
key to select this option. Press
keys to change the settings.
Sets the time to power off the monitor automatically in power saving mode.
Press the
ENTER
key to select this option. Press the or keys to change the settings.
Information
Reset All
Displays the current monitor property settings.
Resets all mode, color and geometry settings to the factory default values.
Press the or keys to change the settings.
• YES
• NO
• ON
• OFF
• ON
• OFF
• OFF
• 10min.
• 20min.
• 30min.
• Input
• Current
Resolution
• Optimum
Resolution
(best with the monitor)
• Model Name
• YES
• NO
How to adjust your monitor 35
Downloaded from ManualMonitor.com Manuals
*DDC/CI, short for Display Data Channel/Command Interface, which was developed by Video Electronics
Standards Association (VESA). DDC/CI capability allows monitor controls to be sent via the software for remote diagnostics.
36 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Appendix: Assembling your monitor with a height adjustment stand (HAS)
How to attach the monitor base
• If the computer is turned on you must turn it off before continuing.
Do not plug-in or turn-on the power to the monitor until instructed to do so.
• The following illustrations are for your reference only. Available input and output jacks may vary depending on the purchased model.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like the monitor packaging bag on the desk for padding.
Gently lay the screen face down on a flat clean padded surface.
While holding the monitor firmly against the desk, pull the monitor stand arm upwards clear of the monitor.
Orient and align the stand base socket with the end of the stand arm, then push them together. Tighten the thumbscrew on the bottom of the monitor base as illustrated.
2
3
1
Gently attempt to pull them back apart to check that they have properly engaged.
Carefully lift the monitor, turn it over and place it upright on its stand on a flat even surface.
Downloaded from ManualMonitor.com Manuals
Appendix: Assembling your monitor with a height adjustment stand (HAS) 37
Extend the monitor to the maximum extended position.
Then tilt the monitor. And rotate the monitor 90 degrees counterclockwise as illustrated.
-90
You might want to adjust the monitor height. See
Adjusting the monitor height on page 40
for more information.
You should position the monitor and angle the screen to minimize unwanted reflections from other light sources.
-5
O
~ +15
O
Downloaded from ManualMonitor.com Manuals
How to detach the base
To move the monitor properly, you should extend the monitor to its maximum height, then place one hand on the upper part of the monitor stand and the other hand on the lower part of the stand as illustrated.
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable.
Gently lift the display up and extend the stand to the maximum extended position.
Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like a towel on the desk for padding, before laying the screen face down on a flat clean padded surface.
Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
2. Release the thumbscrew on the bottom of the monitor base and detach the monitor base as illustrated.
2
3
1
Downloaded from ManualMonitor.com Manuals
Appendix: Assembling your monitor with a height adjustment stand (HAS) 39
Adjusting the monitor height
To adjust the monitor height, hold both the left and the right sides of the monitor to lower the monitor or lift it up to the desired height.
• Avoid placing hands on the upper or lower part of the height-adjustable stand or at the bottom of the monitor, as ascending or descending monitor might cause personal injuries. Keep children out of reach of the monitor while performing this operation.
• If the monitor has been rotated to portrait mode and height adjustment is desired, you should be noted that the wide screen will keep the monitor from being lowered to its minimum height.
Downloaded from ManualMonitor.com Manuals
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 degrees.
Right-click the desktop and select Screen resolution from the popup menu. Select Portrait in
Orientation
, and apply the setting.
Depending on the operating system on your PC, different procedures should be followed to adjust the screen orientation. Refer to the help document of your operating system for details.
2. Fully extend the monitor and tilt it.
Gently lift the display up and extend it to the maximum extended position. Then tilt the monitor.
The monitor should be vertically extended to allow the monitor to rotate from landscape to portrait mode.
3. Rotate the monitor 90 degrees clockwise as illustrated.
To avoid the edge of the LCD display hitting the monitor base surface while it is being rotated, do tilt and extend the monitor to the highest position before you start to rotate the display.
You should also make sure there are no obstacles around the monitor and there is enough room for cables. You might need to route the cables again via the cable clip after the rotation.
90
Downloaded from ManualMonitor.com Manuals
Appendix: Assembling your monitor with a height adjustment stand (HAS) 41
4. Adjust the monitor to the desired viewing angle.
Viewing angle adjustment
You may position the screen to the desired angle with -5° to +15° monitor tilt, 90° (left and right total) monitor swivel, and 110 mm monitor height.
-5
O
~ +15
O
-45
O
~ +45
O
110 mm
Downloaded from ManualMonitor.com Manuals
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, please read the precautions carefully.
Precautions:
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor base.
Lay the screen face down on a clean and well-padded
surface. Detach the monitor base as instructed in How to detach the base on page 39
.
2. Remove the monitor stand.
Use a a cross-pointed screwdriver to release the screws that fixing the monitor stand to the monitor.The use of a magnetic-head screwdriver is recommended to avoid of losing the screws.
Then pull the monitor stand backward away from the monitor.
In case you intend to use your monitor on the stand in the future, please keep the monitor base, monitor stand, and screws somewhere safe for future use.
3. Follow the instruction manuals of the wall mount bracket you purchased to complete the installation.
Downloaded from ManualMonitor.com Manuals
Appendix: Assembling your monitor with a height adjustment stand (HAS) 43
Troubleshooting
Frequently asked questions (FAQ)
The image is blurred:
Read the instructions on the link "Adjusting the Screen Resolution" on the CD, and then select the correct resolution, refresh rate and make adjustments based on these instructions
How do you use a VGA extension cable?
Remove the extension cable for the test. Is the image now in focus? If not, optimize the image by working through the instructions in the "Adjusting the refresh rate" section on the link "Adjusting the Screen Resolution". It is normal for blurring to occur due to conduction losses in extension cables. You can minimize these losses by using an extension cable with better conduction quality or with a built-in booster.
Does the blurring only occur at resolutions lower than the native (maximum) resolution?
Read the instructions on the link "Adjusting the Screen Resolution" on the CD.
Select the native resolution.
Pixel errors can be seen:
One of several pixels is permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another color.
• Clean the LCD screen.
• Cycle power on-off.
• These are pixels that are permanently on or off and is a natural defect that occurs in LCD technology.
The image has a faulty coloration:
It has a yellow, blue or pink appearance.
Select
MENU
>
PICTURE
>
Color
>
Reset Color
, and then choose “
YES
” in the “
Caution
” message box to reset the color settings to the factory defaults.
If the image is still not correct and the OSD also has faulty coloration, this means one of the three primary colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
No image can be seen:
Is the prompt on the display illuminated in green?
If the LED is illuminated in green and there is a message “
Out of Range
” on the screen, this means you are using a display mode that this monitor does not support, please change the setting to one of the supported mode. Please read the “Preset display modes” section from the link "Adjusting the Screen Resolution".
Faint shadow from the static image displayed is visible on the screen:
• Activate the power management function to let your computer and monitor go into a low power "sleep" mode when not actively in use.
• Use a screensaver to prevent the occurrence of image retention.
44 Troubleshooting
Downloaded from ManualMonitor.com Manuals
Is the prompt on the display illuminated in orange?
If the LED is illuminated in orange, the power management mode is active. Press any button on the computer keyboard or move the mouse. If that does not help, check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
Is the prompt on the display not illuminated at all?
Check the power supply mains socket, the external power supply and the mains switch.
The image is distorted, flashes or flickers:
Read the instructions on the link "Adjusting the Screen Resolution" on the CD, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
You are running the monitor at its native resolution, but the image is still distorted.
Images from different input sources may appear distorted or stretched on the monitor running at its native resolution. To have the optimal display performance of each type of input sources, you can use the "Display Mode" function to set a proper aspect ratio for the input
sources. See Display Mode on page 30
for details.
The image is displaced in one direction:
Read the instructions on the link "Adjusting the Screen Resolution" on the CD, and then select the correct resolution, refresh rate and make adjustments based on these instructions.
The OSD controls are inaccessible:
• To unlock the OSD controls when the OSD is preset to be locked, press and hold the
“MENU” key for 15 seconds to enter the “OSD Lock” option and make changes.
• Alternatively, you may use the or keys to select “NO” in the “OSD Lock” submenu from the “OSD Settings” menu (under
SYSTEM
), and all OSD controls will be accessible.
No sound can be heard from the built-in speakers (for models with speakers only):
• Check whether Line In is properly connected.
• Increase the volume (volume may be muted or too low).
• Remove your headphone and/or external speakers. (If they are connected to the monitor, the built-in speakers are automatically muted.)
No sound can be heard from the connected external speakers (for models with speakers only):
• Remove your headphone (if the headphone is connected to the monitor).
• Check whether the headphone jack is properly connected.
• If the external speakers are USB-powered, check whether the USB connection is OK.
• Increase the volume (volume may be muted or too low) on the external speakers.
Need more help?
If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: [email protected].
Troubleshooting 45
Downloaded from ManualMonitor.com Manuals
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project