advertisement
MTP Series
Video and Audio Twisted Pair
Transmitters and Receivers
User Guide
Twisted Pair
68-732-01 Rev. H
11 11
Precautions/Safety Instructions ii
FCC, Copyright, and Trademark Information iii
Safety Instructions • English
I
D
This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.
This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.
Caution
Read Instructions • Read and understand all safety and operating instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future reference.
Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment manufacturer because they may be hazardous.
Consignes de Sécurité • Français
I
D
Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils non recommandés par le fabricant du matériel car cela risquerait de poser certains dangers.
Warning
Power sources • This equipment should be operated only from the power source indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third
(grounding) pin is a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-serviceable parts inside. To prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent overheating of sensitive components inside. These openings must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Avertissement
Alimentations • Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie. Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.
Sicherheitsanleitungen • Deutsch
I
D
Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen
Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung
(Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und die einen elektrischen Schock verursachen können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und
Bedienungsanleitungen genau durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der
Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom
Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.
Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der
Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal durchgeführt werden.
Die internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur
Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird.
Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Instrucciones de seguridad • Español
I Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.
D
Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especificamente recomendados por el fabricante, ya que podrian implicar riesgos.
安全须知
• 中文
I
这个符号提示用户该设备用户手册中有重要的操作和维护说明。
D
这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。
注意
阅读说明书 • 用户使用该设备前必须阅读并理解所有安全和使用说明。
保存说明书 • 用 户应保存安全说明书以备将来使用。
遵守警告 • 用户应遵守产品和用户指南上的所有安全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或追加设备，以避免危险。
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento, es para evitar el sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas siguiendo las instrucciones del fabricante.
警告
电源 • 该设备只能使用产品上标明的电源。 设备必须使用有地线的供电系统供电。 第三条线（
地线）是安全设施，不能不用或跳过 。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后或桌面电源的电源线，或任何接到市电
系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没有用户可以更换的零件。为避免出现触
电危险不要自己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止机内敏感元件过热。 不要用任何东西
挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。必须使用与厂家推荐的相同或相近型号的电池。按
照生产厂的建议处理废弃电池。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and related topics, click here .
Conventions Used in this Guide
In this user guide, the following are used:
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
CAUTION: A caution indicates a potential hazard to equipment or data.
WARNING: A warning warns of things or actions that might cause injury, death, or other severe consequences.
Copyright
© 2011 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
Contents
Introduction
............................................................ 1
About the MTP Transmitters and Receivers .......... 1
TP Cable Advantages .......................................... 2
Transmission Distance ......................................... 2
Installation
.............................................................. 3
Signal Jumpers for Generational Compatibility .... 3
Setting the Jumpers on Non AAP Models ........ 4
Setting the Jumpers on AAP Transmitters ........ 6
Mounting Options .............................................. 7
UL Requirements ............................................. 7
Tabletop Use (All Except AAP Models) ............. 7
Rack Mounting (All Except AAP Models) ......... 7
Rack Mounting Instructions ............................. 8
Furniture or Projector Mounting (All Except
AAP Models) .................................................. 8
Frame Mounting (AAP Models) ....................... 9
Panel Features and Connections ........................ 10
Transmitter Input Connections ...................... 10
Transmitter and Receiver Throughput
Connections ................................................ 12
Power Connection (All Models) ..................... 13
Receiver Output Connections ........................ 15
Operation
.............................................................. 16
Front Panel Features .......................................... 16
Compensation ................................................. 16
Reference Information
....................................... 17
Specifications .................................................... 17
Part Numbers .................................................... 20
MTP Transmitters .......................................... 20
MTP Receivers ............................................... 20
AAP Accessories ............................................ 20
Accessories ................................................... 20
Cables and Connectors ................................. 21
Skew Compensation Solutions ...................... 21
Extron Warranty
.................................................. 22
Contact Information
........................................... 22
MTP Series • Contents v
MTP Series • Contents vi
Introduction
This section introduces the MTP transmitters and receivers. Topics discussed in this section are:
•
About the MTP Transmitters and Receivers
•
•
About the MTP Transmitters and Receivers
The Extron MTP transmitters and receivers provide a system for long-distance distribution of NTSC, PAL, or SECAM video and audio. The MTPs transmit and receive over the Extron
Enhanced Skew-Free ™ A/V UTP cable, Category (CAT) 5 shielded twisted pair (STP), unshielded twisted pair (UTP), or foil shielded twisted pair (FTP) cable.
The MTPs are a part of the Extron line of basic distribution amplifiers, switchers, transmitters, receivers, and associated video accessories.
The MTP transmitters input and the receivers output S-video (luminance [Y] and chrominance [C]) or composite video.
Audio input is either balanced or unbalanced audio on captive screw connectors as well as unbalanced audio on RCA connectors. The transmitters sum the left and right audio channels to convert the audio to mono (L+R) format.
NOTE: MTPs can be jumpered for stereo audio output.
The MTP transmitter then converts the input video and mono audio signals (if applicable) to proprietary signals and outputs them to the compatible MTP receiver on an RJ-45 connector.
Each transmitter requires a compatible receiver. The table on page 2 shows the video and audio capabilities of each model, the transmitter and receiver compatibility, and Architectural
Adapter Plate (AAP) mountability.
The MTPs ship with external desktop 12 V power supplies that accept 100 to 240 VAC,
50-60 Hz input. If jumpers are repositioned from the default settings, a single power supply can power both units if there is less than 200 feet (61 meters) of STP/UTP/FTP cable between the two.
MTP Series • Introduction 1
TP Cable Advantages
Twisted pair (TP) cable is much smaller, lighter, more flexible, and less expensive than coaxial cable. These TP products make cable runs simpler and less cumbersome. Termination of the cable with RJ-45 connectors is simple, quick, and economical.
Transmitters
MTP T SV A
MTP T SV A RCA
MTP SVA AAP
MTP T AV
MTP T AV RCA
MTP T AV AAP
Receivers
MTP R SV A
MTP R SV A RCA
MTP R AV
MTP R AV A RCA
S-Video
•
•
•
•
•
Composite
Video
MTP Series Features
Audio
(Captive
Screw)
Audio
(RCA)
•
•
•
• •
•
•
•
•
•
•
•
•
•
•
AAP
Mounted
•
•
Transmission Distance
Extron suggests a minimum transmission distance of at least 50 feet. The maximum transmission distance when using Enhanced Skew-Free A/V UTP cable or UTP CAT 5 cable, terminated with CAT 5 rated connectors, is 1000 feet.
NOTES: • It is possible to exceed the recommended distance, however, image quality may be reduced.
• The transmitters and receivers are designed for and perform best with Extron
Enhanced Skew-Free A/V cable. CAT 5 cables are acceptable, but are less preferable. We also recommend the use of preterminated and tested cables when possible. Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications.
• The video portion of any S-video transmitter output is compatible with any
S-video receiver in the MTP family described in this manual if the transmitter and receiver jumper configuration are compatible.
• The video portion of any composite video transmitter output is compatible with any composite video receiver in the MTP family described in this guide if the transmitter and receiver jumper configuration are compatible.
• The audio portion of any transmitter output (whether it is equipped with either captive screw or RCA input connectors) is compatible with any audio receiver in the MTP family described in this manual if the transmitter and receiver jumper configuration are compatible.
MTP Series • Introduction 2
Installation
This section describes the installation procedures, including:
•
Signal Jumpers for Generational Compatibility
•
•
Panel Features and Connections
CAUTION: Installation and service must be performed by authorized personnel only.
Signal Jumpers for Generational Compatibility
Over time, the MTPs have been redesigned, affecting the signal content of the TP cable wire pairs, changing the audio from stereo to mono, and eliminating the remote power capability.
The new-generation units are not compatible with the old generation unless an internal jumper in the new unit is shifted.
Shift the jumpers for the new transmitter, receiver, or both if:
• Your installation mixes a transmitter and receiver from different generations.
• You want the units to transmit stereo audio.
• You want one unit to remotely power another.
Use the table below to identify the generation (revision level) of the transmitter and receiver in your installation. If any of the above scenarios are true, reconfigure the jumpers for the units before mounting the units.
NOTE: Only the new generation units have these jumpers.
Transmitter
MTP T SV A
MTP T SV A RCA
MTP T SVA AAP
MTP T AV
MTP T AV RCA
MTP T AV AAP
Old Generation
Part Number
60-540-22
60-541-32
70-362-02, -03
60-540-21
60-540-31
70-361-02, -03
New Generation
Part Number
60-540-52
60-540-62
70-362-22, -23
60-540-51
60-540-61
70-361-22
Receiver
MTP R SV A
MTP R SV A RCA
MTP R AV
MTP R AV RCA
Old Generation
Part Number
60-541-22
60-541-32
60-541-21
60-541-31
New Generation
Part Number
60-541-52
60-541-62
60-541-51
60-541-61
MTP Series • Installation 3
Setting the Jumpers on Non AAP Models
1. Remove and retain the four screws (two on each side of the unit) that secure the cover
Figure 1. Removing the MTP Cover
2. For the receiver, slide the cover slightly forward to clear the front panel adjustment knobs.
3. Lift the cover straight up.
4. If the transmitter or receiver is an audio unit, remove and retain the two screws that secure the audio board to the main (video) board (see
board back until the audio connectors clear the back of the unit and lift the board out of the way.
NOTE: This step (4) and figure 2
are correct for either S-video or composite video models.
Remove these screws.
Transmitter Front Panel Receiver Front Panel
Transmitter Rear Panel
Figure 2. Removing the Audio Board
Receiver Rear Panel
MTP Series • Installation 4
5.
Locate the jumper blocks (see figure 3
) on the video board. Shift the jumper to the alternate location.
Mono (default jumper position)
Compatible with new model transmitter/receivers.
Cannot remotely power transmitter/receiver
Transmitter Front Panel Receiver Front Panel
Transmitter
Rear Panel
Receiver Rear Panel
Stereo
Compatible with old model transmitter/receivers.
Can remotely power transmitter/receiver.
Figure 3. Video Board Jumper Locations
6. Reinstall the audio board and secure it in place with the screws (removed in
).
7. If the receiver is an audio unit, locate the jumper block on the audio board (see
figure 4 ). Shift the jumper to the alternate location.
Receiver Front Panel
Mono (default jumper position)
Compatible with new model transmitters.
Mono audio.
Cannot remotely power transmitter
Stereo
Compatible with old model transmitters.
Stereo audio.
Can remotely power transmitter.
Receiver Rear Panel
Figure 4. Receiver Audio Board Jumper Locations
NOTE: The jumper locations and functions are the same whether the receiver is equipped with captive screw or RCA audio connectors.
8. Replace the cover and the four screws (removed in
MTP Series • Installation 5
Setting the Jumpers on AAP Transmitters
1. Remove and retain the two screws that secure the back cover to the MTP (see
1. Remove these screws.
2. Carefully pull the RJ-45 connector
through this hole.
WER − +
Figure 5. Removing the MTP Cover
2. Pull the cover out of the way, carefully twisting the RJ-45 connector as necessary to slide it through the hole in the cover marked “Output.”
3. Remove and retain the two standoffs that secure the audio board to the main (video) board (see
). Lift the audio board out of the way.
Remove these standoffs.
Figure 6. Removing the Audio Board
4. Locate the jumper block (see
) on the video board. Shift the jumper to the alternate location.
Mono (default jumper position)
Compatible with new model receivers.
Cannot remotely power receiver
Stereo
Compatible with old model receivers.
Can remotely power receiver.
Figure 7. Video Board Jumper Locations
5.
Replace the audio board and secure it in place with the standoffs (removed in step 3 ).
6. Feed the RJ-45 connector through the hole in the cover marked “Output” and replace
the cover. Secure the cover in place with the two screws (removed in step 1 ).
CAUTION: Ensure that the TP cable is not pinched when you reinstall the cover.
MTP Series • Installation 6
Mounting Options
UL Requirements
The following Underwriters Laboratories (UL) requirements pertain to the installation of the
MTP transmitter or receiver into a rack.
1. Elevated operating ambient — If the equipment is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consider installing the equipment in an environment compatible with the maximum ambient temperature (TMA) specified by the manufacturer.
2. Reduced air flow — Installation of the equipment in a rack should be such that the amount of air flow required for safe operation is not compromised.
3. Mechanical loading — Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
4. Circuit overloading — Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
5. Reliable earthing (grounding) — Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections (such as the use of power strips) other than direct connections to the branch circuit.
Tabletop Use (All Except AAP Models)
The non-AAP MTPs come with self-adhesive rubber feet attached to the four corners of the bottom. Set the MTP on a horizontal surface.
Rack Mounting (All Except AAP Models)
For optional rack mounting, mount the MTP on any of the following rack shelves:
• RSF 123 universal rack shelf for 3.5 inch deep products (part number: 60-190-20)
• RSB 123 basic rack shelf for 3.5 inch deep products (part number: 60-604-21)
• RSU 126 universal rack shelf for 6 inch deep products (part number: 60-190-10)
• RSB 126 basic rack shelf for 6 inch deep products (part number: 60-604-11)
• RSU 129 universal rack shelf for 9.5 inch deep products, (part number: 60-190-01)
• RSB 129 basic rack shelf for 9.5 inch deep products (part number: 60-604-02)
MTP Series • Installation 7
Rack Shelf
Quarter Rack Width
False Front Face Plate
Eighth Rack Width
False Front Face Plate
(2) 4-40 x 3/16"
Screws
Figure 8. Mounting the MTPs on a Rack Shelf
Figure 9. Mounting the MTPs on a
Standard Rack Shelf
Rack Mounting Instructions
On the standard rack shelf, the MTP mounts in one of eight locations to the rear of the rack or in one of eight locations to the front of the rack.
1. Remove the feet from the bottom of the MTP, if installed.
2. Mount the MTP using two 4-40 x 3/16 inch screws in opposite (diagonal) corners to secure the MTP to the shelf.
3. Install blank panels or other units to the rack shelf.
Furniture or Projector Mounting (All Except AAP Models)
Use the optional mounting kit (furniture, part number: 70-212-01, or projector, part number: 70-217-01) to mount the MTP as follows:
1. Remove the feet from the bottom of the MTP, if installed.
2. Attach the mounting brackets to the MTP with the machine screws provided (see
).
•
•
If furniture mounting, proceed to step 3 .
If projector mounting, proceed to
.
Mounting
Bolt
Projector
Mounting
Bracket
Ceiling
Projector
Under Desk Mounting Projector Mounting
Figure 10. Desk and Projector Mounting the MTPs
MTP Series • Installation 8
3. For furniture mounting — a. Hold the MTP with the attached brackets against the underside of the mounting surface. Mark the bracket screw hole locations on the mounting surface.
b. Drill 3/32 inches (2 mm) diameter pilot holes, 1/4 inch (6.3 mm) deep in the mounting surface at the marked screw locations.
c. Insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting surface until just less than 1/4 inch of the screw head protrudes.
d. Align the mounting screws with the slots in the brackets and place the MTP against the surface.
e. Slide the MTP slightly forward or back, then tighten all four screws to secure the
MTP in place.
4. For projector mounting — secure the MTP to a projector mount by inserting the mounting bolt through the slotted hole in the bracket.
Frame Mounting (AAP Models)
The AAP-mountable transmitters (MTP T SVA AAP and MTP T AV AAP) can be mounted to any Extron AAP mounting frame that accepts a double space (double height) AAP module
(see “
AAP Accessories ” for a partial list of AAP devices).
NOTE: The rear panel MTP connections will be inaccessible after installation. Make all
connections (see “ Transmitter and Receiver Throughput Connections ”) and
test the twisted pair system (apply a video source and observe that transmitted video is displayed satisfactorily) before installing the panel-mounted transmitter.
Install an MTP transmitter in an AAP frame as follows (see figure 11
):
AAP 102
AAP 102
VIDEO
IN
AUD
L
IO IN
MTP
R
T AV
AAP
MTP T AV AAP
Figure 11. AAP Mounting an MTP Transmitter
1. If necessary, remove the AAP frame from the device.
2. Cable the rear of the transmitter before fastening the AAP module to the AAP frame.
3. Insert each of the AAP module screws through the holes in the AAP frame. Secure the transmitter to the frame with the provided captive washers and #4-40 nuts.
4.
Install the AAP frame as appropriate to the type of frame. Figure 11
shows the transmitter module being installed in an AAP 102 wall mounting frame and the frame being installed in a wall box.
MTP Series • Installation 9
Panel Features and Connections
Transmitter Input Connections
Figure 12 shows all of the combinations of video and audio input connectors that you may
encounter with your MTP transmitter.
NOTE: Some transmitters do not have audio connections.
L
INPUT
R L
INPUT
R
3 3
12V
0.5a
MAX
S-VIDEO
1
OUTPUT
MTP T SV A
MTP T SV A,
Rear Panel
INPUT
4
L R
12V
0.5a
MAX
S-VIDEO OUTPUT
MTP T SV A RCA
1
MTP T SV A RCA,
Rear Panel
1 4
4
12V
0.5a
MAX
VIDEO
2
OUTPUT
MTP T AV
MTP T AV,
Rear Panel
INPUT
L R
2
12V
0.5a
MAX
VIDEO OUTPUT
MTP T AV RCA
2
MTP T AV RCA,
Rear Panel
4
S-VIDEO
IN
R
AUDIO IN
L
MTP T SVA
MTP T SVA AAP,
Front Panel
VIDEO
IN
R
AUDIO IN
L
MTP T AV
MTP T AV AAP,
Front Panel
Figure 12. Video and Audio Input Connections a
S-video connector (SV models) — Connect an S-video input to this 4-pin mini DIN connector.
b
Composite video connector (AV models) — Connect a composite video input to this connector (female RCA on the MTP T AV AAP, female BNC on all other models).
c
Audio input captive screw connector (MTP T SV A, MTP T AV) — Connect a balanced or unbalanced audio input to this 3.5 mm, 5-pole captive screw connector.
Connectors are included with each MTP, but you must supply the audio cable. See
to wire a connector for the appropriate input type. Use the supplied tiewrap to strap the audio cable to the extended tail of the connector. High impedance is generally over 800 ohms.
Do not tin the wires!
Tip
Sleeve
Tip
Sleeve
Unbalanced Stereo Input
(high impedance)
Tip
Ring
Sleeve (s)
Tip
Ring
Balanced Stereo Input
(high impedance)
Figure 13. Captive Screw Input Connector Wiring
MTP Series • Installation 10
CAUTIONS: • The length of the exposed (stripped) portion of the copper wires is important. The ideal length is 3/16 inches (5 mm). Longer bare wires can short together. Shorter bare wires are not as secure in the direct insertion connectors and could be pulled out.
• The captive screw audio connector can easily be inadvertently plugged partially into one receptacle and partially into an adjacent receptacle. This misconnection could damage the audio output circuits. Ensure that the connector is plugged fully and only into the desired input or output
NOTES: • When making connections for the MTP from existing audio cables, see
to identify the tip, ring, and sleeve wires in various connectors.
• A mono audio connector consists of the tip and sleeve.
• A stereo audio connector consists of the tip, ring, and sleeve.
• The ring, tip, and sleeve wires are also shown on the captive screw audio
connector diagrams (see figure 13
and
Tip (+)
Tip (L)
Ring (R)
Sleeve ( )
RCA Connector (Mono)
Sleeve ( )
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 14. Typical Audio Connectors d
Audio input RCA connectors (RCA and AAP models) — Connect an unbalanced
stereo audio source to these L(eft) and R(ight) RCA connectors (see figure 15
).
Tip (Signal)
Right Channel
(Red Jacket)
Sleeve (Gnd )
Left Channel
(White Jacket)
Figure 15. RCA Audio Connectors
MTP Series • Installation 11
Transmitter and Receiver Throughput Connections
Figure 16 identifies the connections between the transmitter and receiver.
MTP Transmitters
INPUT
MTP Receivers
OUTPUT
L R L R
12V
0.5a
MAX
S-VIDEO OUTPUT
MTP T SV A RCA
5
L
INPUT
R
12V
0.5a MAX
INPUT
S-VIDEO
MTP R SV A RCA
5
L
OUTPUT
R
12V
0.5a MAX
VIDEO OUTPUT
MTP T AV
12V
0.5a MAX
INPUT
VIDEO
MTP R AV
5
WER − +
Figure 16. Throughput Connections
CAUTION: Do not connect these devices to a computer data or telecommunications network.
NOTE: RJ-45 termination must comply with the TIA/EIA T 568A or TIA/EIA T 568B wiring standards for all connections.
e
Transmitter output and receiver input connector — Connect one end of a TP cable to this RJ-45 female connector on the transmitter. On the MTP T SV A AAP and
MTP T AV AAP, the connector is at the end of a short pigtail.
Connect the free end of the same TP cable from the transmitter to this RJ-45 female connector on the receiver.
MTP Series • Installation 12
TP cable termination
Figure 17 details the recommended termination of TP cables with RJ-45 connectors in
accordance with the TIA/EIA T 568A or TIA/EIA T 568B wiring standards. You can use either standard, but ensure that you use the same standard on both cable ends.
WARNING: Damage may occur to the unit if TP cables are miswired as crossover cables.
Pins:
12345678
Insert Twisted
Pair Wires
RJ-45
Connector
Crossover Cable
Pin
1
End 1
Wire color
White-green
2
3
4
5
6
7
8
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
End 2
Wire color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
T568A
A cable that is wired as T568A at one end and T568B at the other (Tx and Rx pairs reversed) is a "crossover" cable.
T568B
Straight-through Cable
Pin
1
End 1
Wire color
White-orange
2
3
4
5
6
7
8
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
End 2
Wire color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
T568B T568B
A cable wired the same at both ends is called a "straight-through" cable, because no pin/pair assignments are swapped.
Figure 17. TP Cable Termination
NOTES: • Enhanced Skew-free A/V cable is not recommended for Ethernet/LAN applications.
• This cable is specially designed for compatibility with Extron Twisted Pair products, wired using the TIA/EIA 568 A standard.
• The green, brown, and blue pairs of this cable have virtually identical lengths and should be used to transmit the video signals.
• The orange pair of this cable has a different length and should not be used to transmit the video signals.
Power Connection (All Models)
See
figure 18 to identify the power connections and indicators and to identify the panel
screws.
MTP Transmitters MTP Receivers
INPUT OUTPUT
L R L R
7 7
12V
0.5a MAX
S-VIDEO OUTPUT
MTP T SV A RCA
6
MTP AAP Transmitters
12V
0.5a MAX
INPUT
S-VIDEO
MTP R SV A RCA
6 7
WER − +
VIDEO
IN
R
AUDIO IN
L
MTP T AV
6
Figure 18. Power Connections and Indicators
MTP Series • Installation 13
f
Power connector — Plug the external 12 VDC power supply into this 2-pole captive
screw connector on both the transmitter and the receiver. Figure 19
shows how to wire the connectors.
Smooth
A
Ridges
A
Power Supply
Output Cord
SECTION A–A
Tie Wrap
3
5
Captive Screw Connector
Figure 19. Power Connector Wiring
WARNING: The two power cord wires must be kept separate while the power supply is plugged in. Remove power before wiring.
NOTES: • If the transmitter and receiver are either older generation units or jumper configured to the stereo audio position (compatible with the older units), only a single device needs to be powered in a two-unit system
(see “
Signal Jumpers for Generational Compatibility” on page 3).
The device connected to the power supply, in turn, provides power to its counterpart.
• If the transmitter and receiver are separated by greater than 200 feet
(61 meters) of STP/UTP/FTP cable, connect a power supply to both units.
This remote power application is only available in stereo mode, not mono mode.
• Do not tin the stripped power supply leads before installing the captive screw or direct insertion connector. Tinned wires could be pulled out because they are not as secure in the captive screw and direct insertion connectors.
CAUTIONS: • Power supply voltage polarity is critical. Incorrect voltage polarity can damage the power supply and the MTP. Identify the power cord negative
lead by the ridges on the side of the cord (see figure 19
).
• The length of the exposed (stripped) copper wires is important. The ideal length is 3/16 inches (5 mm). Longer bare wires can short together.
Shorter wires are not as secure in the captive screw connectors and could be pulled out.
To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter.
Use the supplied tie-wrap to strap the power cord to the extended tail of the connector.
NOTE: Your transmitter/receiver pair may have shipped with a blue captive screw connector. This blue connector can be plugged into either a blue or an orange power receptacle.
The blue connector does not have an extended tail or the included tie-wrap.
Alternatively, an optional Extron PS 124 Universal 12 VDC Power Supply (part number
60-1022-01) can power multiple Extron 12 VDC devices using only one AC power connector.
g
Power LED — Indicates power is applied to the MTP.
MTP Series • Installation 14
Receiver Output Connections
See
figure 20 to identify the receivers rear panel output connections. The figures show all of
the combinations of connectors that you may encounter with your MTP receiver.
10
MTP R SV A,
Rear Panel
L
OUTPUT
R
11
MTP R SV A RCA,
Rear Panel
OUTPUT
L R
12V
0.5a MAX
INPUT
S-VIDEO
MTP R SV A
MTP R AV,
Rear Panel
10
L
OUTPUT
R
8
11
12V
0.5a MAX
INPUT
S-VIDEO
MTP R SV A RCA
MTP R AV RCA,
Rear Panel
OUTPUT
8
L R
12V
0.5a MAX
INPUT
VIDEO
MTP R AV
12V
0.5a MAX
INPUT
VIDEO
MTP R AV RCA
9 9
Figure 20. Output Connector Wiring h
S-video connector (SV models) — Connect an S-video device to this 4-pin mini DIN connector.
i
Composite video connector (AV models) — Connect a composite video device to this BNC connector.
j
Captive screw audio connector (MTP R SV A, MTP R AV) — Connect a balanced or unbalanced audio device, such as an audio amplifier, to this 3.5 mm, 5-pole captive
screw connector (see figure 21
to properly wire the output connector).
Tip
Sleeve
Tip
Sleeve
Tip
Ring
Sleeve (s)
Tip
Ring
Do not tin the wires!
Unbalanced Stereo Input
(high impedance)
Balanced Stereo Input
(high impedance)
Figure 21. Captive Screw Connector Wiring for Audio Output
NOTE: Some receivers do not have audio connections.
CAUTIONS: • Connect the sleeve to ground (Gnd). Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.
• The length of the exposed (stripped) portion of the copper wires is important. The ideal length is 3/16 inches (5 mm).
• Longer bare wires can short together.
• Shorter bare wires are not as secure in the direct insertion connectors and could be pulled out.
k
RCA audio connectors (RCA models) — Connect a stereo audio device to these L(eft) and R(ight) RCA connectors.
MTP Series • Installation 15
Operation
This section describes:
•
•
Troubleshooting — Skew Delay Compensation
Front Panel Features
MTP R Composite Video
Receiver Front Panel
MTP R S-video Receiver
Front Panel
1 3 2 1 3 3 2
Figure 22. MTP Receiver Front Panels a
Power LED — When lit, this LED indicates power is applied to the MTP.
b
Sharpness — Adjusts the output image sharpness for long cable runs.
c
Gain control — Adjusts the brightness of the output image to compensate for long cable runs.
S-video receivers — There are separate controls for luminance (Y) and chrominance (C) on S-video MTP receivers. If the chrominance setting on the MTP receiver S-video output is too low, the image may appear in monochrome. Adjust the S-video gain until color appears.
Composite video receivers — There is only one gain control on composite video MTP receivers.
NOTE: All control knobs are removable to limit access if desired.
Troubleshooting — Skew Delay Compensation
CAT 5 TP cable can cause registration errors (in which luminance leads or lags chrominance) between the Y and C video signals on S-video transmitter/receiver pairs. Try using the following methods to minimize or eliminate pair skew:
• Switch to Extron Enhanced Skew-Free A/V UTP cable.
• Add an S-video-to-BNC adapter and a skew compensation cable equal to the length of pair skew to the receiver output.
• Install an S-video-to-BNC adapter and an SEQ 100 15 HD Skew Equalizer on the receiver video output and adjust the skew for the leading video image.
MTP Series • Operation 16
Reference
Information
This section provides information on:
•
•
Specifications
Video
Gain .............................................. Unity
Differential phase error .................. <1.0º at 3.58 MHz and 4.43 MHz
Differential gain error .................... <1.0% at 3.58 MHz and 4.43 MHz
Video input
Number/signal type
MTP T AV Series ................. 1 composite video
MTP T SV Series ................. 1 S-video
MTP R AV/SV Series ............ 1 set of proprietary analog signals
Connectors
MTP T AV Series ................. 1 female BNC
MTP T AV AAP ................... 1 female RCA
MTP T SV Series ................. 1 female 4-pin mini DIN
MTP R AV/SV Series ............ 1 female RJ-45
Nominal level ................................. 1 Vp-p for Y of S-video and for composite video
0.3 Vp-p for C of S-video
Minimum/maximum levels .............. 0.3 V to 1.5 Vp-p with no offset
Impedance .................................... 75 ohms
Return loss .................................... <-30 dB, DC @ 10 MHz
DC offset (max. allowable) ............. 100 mV
Video output
Number/signal type
MTP T AV/SV Series and MTP T AAP Series
1 set of proprietary analog signals
MTP R AV Series ................. 1 composite video
MTP R SV Series ................. 1 S-video
Connectors
MTP T AV/SV Series ............ 1 female RJ-45
MTP T AAP Series ............... 1 female RJ-45 on a 3” (7.6 cm) pigtail
MTP R AV Series ................. 1 female BNC
MTP R SV Series ................. (1) 4-pin mini DIN
Nominal level ................................. 1 V p-p for Y of S-video and for composite video
0.3 V p-p for C of S-video
Minimum/maximum levels .............. 0.3 V to 1.5 Vp-p
Impedance ..................................... 75 ohms
Return loss .................................... <-35 dB @ 5 MHz
DC offset ...................................... ±20 mV with input at 0 offset
MTP Series • Reference Information 17
Sync
Standards ....................................... NTSC 3.58, NTSC 4.43, PAL, SECAM
Audio
Gain
RCA models ....................... Unbalanced output: 0 dB (unity)
All other models ................ Unbalanced output: 0 dB (unity); balanced output: +6 dB
Frequency response ....................... 20 Hz to 20 kHz, ±0.25 dB
THD + Noise .................................. 0.03% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N
RCA models ....................... >90 dB, at maximum output (unweighted)
All other models w/audio ... >90 dB, balanced at maximum output (unweighted)
Crosstalk ....................................... <-80 dB @ 1 kHz, fully loaded
Stereo channel separation ............. >75 dB @ 1 kHz
CMRR ............................................ >34 dB @ 20 Hz to 20 kHz
Audio input
Number/signal type
MTP T AV, MTP T SV A ...... 1 stereo, balanced/unbalanced
MTP T AV/SV A RCA, MTP T AAP, MPT T 45 Series
1 stereo, unbalanced
.......................................... 1 stereo, unbalanced
MTP R Series ...................... 1 set of proprietary analog signals
Connectors
MTP T AV, MTP T SV A ....... (1) 3.5 mm captive screw connector, 5 pole
MTP T AV/SV A RCA, MTP T AAP
1 pair of RCA female
MTP R Series ...................... 1 female RJ-45 (shielded)
Impedance .................................... >5.6k ohms ±5% unbalanced, >10k ohms ±5% balanced
Nominal level ................................. -10 dBV (0.32 Vrms)
Maximum level .............................. >+2.4 dBu (balanced or unbalanced) at 1%THD+N
NOTE: 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu.
Audio output
Number/signal type
MTP T Series (all models) .... 1 set of proprietary analog signals
MTP R AV, MTP R SV A ....... 1 stereo or dual mono, balanced/unbalanced
MTP R AV/SV A RCA .......... 1 stereo or dual mono, unbalanced
Connectors
MTP T Series ...................... 1 female RJ-45 (shielded)
MTP T AAP Series ............... 1 female RJ-45 on a 3” (7.6 cm) pigtail
MTP R AV, MTP R SV A ....... (1) 3.5 mm captive screw connector, 5 pole
MTP R AV/SV A RCA .......... 1 pair of RCA female
Impedance
MTP R AV, MTP R SV A ....... 50 ohms unbalanced, 100 ohms balanced
MTP R AV/SV A RCA .......... 50 ohms unbalanced
Gain error ..................................... ±0.1 dB channel to channel
Maximum level (Hi-Z) ..................... >+3.3 dBu, balanced or unbalanced at 1%THD+N
Maximum level (600 ohm) ............. >+2.0 dBm, balanced or unbalanced at 1%THD+N
MTP Series • Reference Information 18
General
Recommended cable type .............. CAT5/5e/6 (shielded or unshielded)
External power supply .................... 100 VAC to 240 VAC, 50-Hz, external; to 12 VDC, 1.0 A, regulated
Power input requirements .............. 12 VDC, 0.2 A
NOTES: • If the distance between the transmitter and receiver is less than 500 feet (150 m) and if the internal jumper is in setting 2, you can connect a power supply to only one device in a transmitter/receiver pair.
• If the distance between transmitter and receiver is greater than 500 feet (150 m) or if the internal jumper is in setting 1 (default), connect a power supply to each device.
Temperature/humidity .................... Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling .......................................... Convection, no vents
Mounting
Rack mount
MTP T AAP Series ............... Yes, with optional rack panel
All other models................. Yes, with optional 1U deep rack shelf
Furniture or wall mount
MTP T AAP Series ............... Yes, with optional AAP mounting plates
All other models................. Yes, with optional brackets
Enclosure type ............................... Metal
Enclosure dimensions .................... (Depths exclude connectors and cables.)
MTP T AAP Series
Faceplate ........................... 1.4” H x 3.5” W x 0.1” D
(3.6 cm H x 8.9 cm W x 0.3 cm D)
(double space AAP plate)
Transmitter ........................ 1.35” H x 2.7” W x 1.3” D
(3.4 cm H x 6.9 cm W x 3.3 cm D)
All other models ...................... 1.7” H x 2.2” W x 3.0” D
(1U high, one-eighth rack wide)
4.2 cm H x 5.6 cm W x 7.6 cm D
Product weight ............................... 1.0 lbs (0.5 kg)
Shipping weight ............................ 3 lbs (2 kg)
Vibration ....................................... ISTA 1A in carton
(International Safe Transit Association)
Regulatory compliance
Safety ...................................... CE, c-UL, UL
Compliances ............................ CE, C-tick, FCC Class A, ICES, VCCI
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
NOTES: • All nominal levels are at ±10%.
• Specifications are subject to change without notice.
MTP Series • Reference Information 19
Part Numbers
MTP Transmitters
Description
MTP T SV A
MTP T SV A RCA
MTP T SVA AAP (black, white)
MTP T AV
MTP T AV RCA
MTP T AV AAP (black)
MTP Receivers
Description
MTP R SV A
MTP R SV A RCA
MTP R AV
MTP R AV RCA
Part Numbers
60-540-52
60-540-62
70-362-22, 23
60-540-51
60-540-61
70-361-22
Part Numbers
60-541-52
60-541-62
60-541-51
60-541-61
AAP Accessories
Accessories
AAP 102 panel (black, white)
AAP 104 panel (black, white, RAL9010 white)
Part Numbers
60-300-02, 03
60-301-02, 03, 05
AAP 106 panel (gray, black, white) 60-531-01, 02, 03
AAP 201 panel - half rack width, 1U (gray, black, white) 60-302-01, 02, 03
AAP 202 panel - half rack width, 2U ( black, white)
AAP 301 panel - full rack width, 1U (black)
60-303-02, 03
60-632-02
AAP 302 panel - full rack width, 2U (black) 60-633-02
Accessories
Accessories
PS 124 multiple output 12 Volt DC power supply
RSU 129 9.5” 1U universal rack shelf kit (gray)
RSB 129 9.5” 1U basic rack shelf (gray)
RSU 126 6” deep 1U universal rack shelf kit (gray)
RSB 126 6” deep 1U basic rack shelf (gray)
RSF 123 universal rack shelf (gray)
RSB 123 basic rack shelf (gray)
MBU 123 furniture mounting kit
PMK 100 projector mounting kit
Part Numbers
60-1022-01
60-190-01
60-604-02
60-190-10
60-604-11
60-190-20
60-604-21
70-212-01
70-217-01
MTP Series • Reference Information 20
Cables and Connectors
NOTE: Enhanced Skew-Free™ A/V UTP cables are not recommended for Ethernet/LAN applications.
Enhanced Skew-Free™ A/V Cable
Enhanced Skew-Free A/V UTP (various lengths)
Enhanced Skew-Free A/V UTP, bulk
Plenum Enhanced Skew-Free A/V UTP, bulk
RJ-45 Connector
CAT 6 jack (black)
CAT 6 jack (red)
CAT 6 jack (blue)
CAT 6 jack (orange)
CAT 6 jack (gray)
CAT 6 jack (white)
CAT 6 jack (ivory)
S-video to BNC Adapter
S-video 4-pin male to 2 BNC female - 8” (20 cm)
S-video 4-pin male to 2 BNC female - 1’ (30 cm)
S-video 4-pin male to 2 BNC female - 3’ (90 cm)
S-video 4-pin male to 2 BNC female - 6’ (1.8m)
S-video 4-pin female to 2 BNC male - 1’ (30 cm)
Part Numbers
26-569-xx
22-141-03
22-142-03
Part Numbers
100-476-01
100-477-01
100-478-01
100-479-01
100-480-01
100-481-01
100-482-01
Part Numbers
26-353-01
26-353-02
26-353-03
26-353-04
26-541-02
Skew Compensation Solutions
Skew Equalizer
SEQ 100 15HD
Part Numbers
60-676-01
MTP Series • Reference Information 21
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America, and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle
East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions, or modifications were made to the product that were not authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: (714) 491-1500
Asia: 65.6383.4400
Europe: 31.33.453.4040
Japan: 81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Contact Information
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project