Operator’s Manual & Parts List US9456702 (04-08)

Operator’s Manual & Parts List US9456702 (04-08)
US9456702 (04-08)
Operator’s Manual & Parts List
Compression Sprayers: 454, 456, 456 SW, 457,
454HD, 456HD, 457HD, 454V, 456V, 457V, 407CI
year
warranty
STOP! If you are missing parts, instructions or have questions, DO NOT take this unit back to the
store. Call 1-800-SOLO-INC. Solo will send the missing parts/information to you promptly.
WARRANTY:
Solo model 454, 456, 456 SW & 457 sprayers are covered by Solo’s 5-YEAR LIMITED WARRANTY. Solo manufactured parts which
fail due to defective material or workmanship will be repaired or replaced without charge. See page 6 for full details.
SAFETY PRECAUTIONS:
•
•
•
•
•
•
•
•
•
•
Do not exceed 45 psi pressure.
Do not fill with, use or spray flammable materials.
Do not use gasoline, acid, caustic or potentially injurious chemicals.
At the time of manufacture of this sprayer, we are not aware of any approved plant protection chemicals which
would adversely affect this sprayer when applied in their usual concentration.
Observe the recommendations of the chemical manufacturer.
Prior to removing any part of the sprayer pull the pressure relief valve to release any pressure in the tank.
Wear rubber gloves, safety goggles and appropriate protective clothing.
After pumping be sure handle is in the locked down position.
Individuals should be trained in the proper use of this sprayer. Where training is not available, individuals
should study and follow the procedures detailed in this manual.
Do not use acetone based chemicals.
WARNING:
Chemicals can be harmful to individuals and the environment if improperly used. In addition, some chemicals are caustic, corrosive, or
poisonous and should be avoided. Read warnings and chemical manufacturer’s instructions. Solo high density polyethylene sprayers
are fitted with Viton® seals which are resistant to a wide variety of agricultural, industrial and household chemicals; however, care
should be exercised to ensure that sprayer components are clean, functioning properly, and in a good state of repair before and during
use. If in doubt about a particular chemical, check with manufacturer. If you suspect or observe indications that the material may be
unsafe in a Solo sprayer... STOP! Do Not Use or Apply Chemical. ALWAYS WEAR RUBBER GLOVES, SAFETY GOGGLES AND
APPROPRIATE PROTECTIVE CLOTHING.
• Read and follow operating instructions.
• Do not fill sprayer over maximum fill mark. Releasing pressure in an overfill condition can cause harmful venting of sprayer contents.
• Relieve pressure only with sprayer upright and while standing on the side of the sprayer opposite the pressure relief valve. Venting
of sprayer contents can occur if liquid is over bottom of relief valve.
• CAUTION: To prevent injury from ejected pump assembly and/or solution, never stand with face or body over the top of the tank
when pumping, or loosening pump.
• Do not modify sprayer or pressure relief valve.
Screw Cap
• Never spray in the direction of humans, animals or property which might be injured or
damaged by spray formula.
Wand
• Do not use disinfectants, solvents or impregnating agents unless first tested to ensure
they are not harmful to the environment and sprayer.
• Do not use liquids with a temperature above 120°F (45°C).
• Remember that a sprayer with liquid is a significant amount of weight (8 lbs. per
Install Wand Here
gallon). Use caution when bending, leaning or walking. Bend only at the knees and
O-Ring
support yourself as required to ensure personal safety.
Optional Pressure
• Do not inflate sprayer without liquid in the tank.
Gauge Mounts Here
• Do not climb on ladders, trees or other unsteady or potentially unsafe structures.
Assembly Instructions for Wand
Shut-Off Valve
1. Ensure that the O-ring is on the non-threaded end of the wand.
2. Insert the non-threaded end of the wand into the O-ring into the open end of the shut-
off valve.
3. Tighten the screw cap.
CUSTOMER SERVICE COMMITMENT FROM SOLO’S SERVICE DEPARTMENT
In the event the sprayer you have purchased has missing or damaged parts, please call 1-800-765-6462, 9:00 AM—5:00 PM EST.
In order to assist your service representative, please have the following information available: sprayer model number, part description
and part number. A parts list is included in your operator’s manual.
Solo is committed to your satisfaction and is continuing its efforts to earn your future business.
Visit us on the web at www.solousa.com
Troubleshooting and parts ordering available online.
CLEANING:
Using the Adjustable Nozzle
To change the spraying pattern, first make sure the retaining nut
(2) is screwed tight to the elbow (5). If it is not tight, the nozzle
cap (1) and nozzle body (3) will
rotate inside the retaining nut and
1. Nozzle cap
the nozzle will not adjust. For a
2. Retaining nut
straight stream pattern, rotate the
nozzle cap outward. For a hollow
3. Nozzle body
cone pattern, rotate the nozzle cap
inward towards the retaining nut.
If it becomes difficult to rotate the 4. Filter with gasket
nozzle cap, remove the nozzle cap
5. Elbow
from the nozzle body and lubricate
the O-ring on the nozzle body with
a non-water soluble grease*.
•
•
•
•
•
•
•
•
•
MAINTENANCE:
Removing Adjustable Nozzle
•
•
Unscrew the nozzle cap (1) from the nozzle body (3). This
is best accomplished while the retaining nut (2) is securely
fastened to the elbow (5). Next, unscrew the retaining nut (2).
Push the nozzle body (3) out of the retaining nut (2). The filter
(4) will come out with the body. To re-install the nozzle, reverse
the above instructions.
•
OPERATION:
•
•
•
•
•
•
•
Carefully clean sprayer after every use.
Pour or spray all remaining chemical out of sprayer.
Pour a small amount of water for water soluble chemicals, or
mineral spirits for oil-based chemicals, into the tank.
Pressurize and spray through system until all liquid is gone.
Repeat process with warm soapy water.
Repeat process with warm clear water.
Use an absorbent cloth to dry all internal surfaces.
Follow the recommendations of the chemical manufacturer for
disposing of waste water and chemicals.
Do not use aggressive or abrasive cleaning agents.
Before using sprayer with chemicals, fill sprayer with fresh
water to assure that you have it properly assembled;
pressurize and then practice spraying. When thoroughly
familiar with sprayer operation, follow normal operating
procedures.
Turn pump handle counter clockwise to remove pump.
Fill tank with premixed formula up to desired level. (Do not
exceed maximum fill mark.) Observe recommendations of
chemical manufacturer.
Tighten cap and pump assembly for a good seal.
Pump to a maximum 45 psi or 3 bar pressure. The valve
stem on the pressure relief valve will rise up to vent excess
pressure over 45 psi.
Start or stop spraying by squeezing or releasing the lever on
the shut-off valve (3). The spray pressure can be monitored
with an optional pressure gauge.
Prior to every removal of pump (1), release pressure first by
pulling up on the pressure relief valve stem (2).
•
1
Prior to storage, empty, clean and dry sprayer.
Always store the sprayer in a dry area, protected from
freezing, heat and sunlight.
Lubricate O-ring in pressure relief valve with non-water
soluble grease* on a regular basis.
Disassembly: Unscrew pressure relief valve from tank
and pull the valve body out of the screw cap. Clean,
lubricate, and replace.
Pump Maintenance: Pump pressure sealing is accomplished
with an O-ring (5) on the pump piston (4) which moves within
the cylinder (3). Periodically this O-ring should be greased
with a non-water soluble grease*. If worn, it should be
replaced. A small umbrella valve at the bottom of the cylinder
prevents the formula from entering the cylinder. Keep these
parts clean and replace if worn.
Disassembly: Unscrew pump assembly from tank.
Carefully remove umbrella valve (6) from the bottom of
cylinder (3). While holding cylinder firmly with one hand
and the handle of the pump piston (4) firmly in the other,
with the piston fully inserted in the cylinder, pull back on
the piston quickly and forcefully. To re-assemble, place
the piston assembly back into cylinder, place heel of
hands on opposite sides of the tank cap, while keeping
cylinder in place with fingers, tap bottom of cylinder
against a flat padded surface. Assembly will lock into
place.
6
2
•
•
3
2
Tank Cap: A small amount of non-water soluble grease*
on tank cap threads and both sides of the gasket eases
tightening and loosening.
Regular Inspection: Inspect and replace worn or damaged
parts promptly. Pay particular attention to tank cap gasket,
pressure relief valve and seal, inflation valve (if fitted),
umbrella valve O-rings and seals throughout sprayer. Regular
lubrication of O-rings and seals is recommended.
* Solo Superior Grease or petroleum jelly work well.
OPERATING FEATURES:
Nozzles - Your Solo sprayer is standard with nozzle arrangements which provide a variety of spray patterns.
Item
Application
Part #
Flat spray nozzle
Row treatment
4074263
Jet stream nozzle
Spot & longer range4074755
Item
Application
Part #
Jet stream nozzle
and swirl plate =
hollow cone
Shrubs and bushes4074755
Plastic adjustable
4900527
Spot, shrubs & bushes
Spray tips should be assembled as follows for desired spray patterns.
SPRAY TIP ASSEMBLY
1. Flat spray nozzle
5. Nozzle cap
2. Filter
6. Nozzle body
3. Jet cap
7. Brass adj. nozzle*
4. Swirl plate
8. Nozzle retaining nut
*Brass adjustable nozzle is not a standard item on all Solo sprayers.
Flat spray
Hollow
cone spray
No-drip-check valve
replaces # 2 on heavy-duty
models
Brass
adjustable
nozzle*
Jet stream
Plastic
adjustable
nozzle
In the best interest of continued technological progress, we reserve the right to change design and configuration of any product without prior or other notice.
Therefore, please note that text and illustrations of this manual are not to be considered binding and do not constitute a basis for legal or other claims.
WHAT SPRAY NOZZLE SHOULD I USE?
A flat spray nozzle is supplied for spraying paths, garden
beds, and general area spraying. A cone nozzle is also
supplied for spot spraying and for the treatment of bushes
and small trees. For spot spraying, simply remove swirl plate
from behind nozzle tip. Save the swirl plate for future use.
Available as an option is a reflux filter with a built-in check
valve (27 00 316) which opens at 5 psi and closes at 4 psi.
This virtually eliminates the dripping of fluid still contained
in the spray wand. A wide selection of nozzles such as
deflector, adjustable, and anti-drift nozzles are available.
WILL THE PLASTIC MATERIAL LAST?
Only high-grade polyethylene is used. The material is
chosen for high molecular weight, high-impact strength,
and excellent resistance to chemicals and stress.
Ultraviolet inhibitors are used in the material to reduce
deterioration caused by sunlight.
HOW HEAVY IS THE UNIT?
Compression sprayers weigh approximately 5 1/2 lbs.
CAN I USE WEED KILLER AND INSECTICIDE IN
THE SAME SPRAYER?
In theory you can, if the sprayer is thoroughly cleaned
out with a bleach water solution of 1:25. In practice, the
use of both types of chemicals in the same unit is not
recommended as the risk to plants can be high. Use
caution when handling any type of chemicals and when
cleaning your sprayer. Do not mix cleaning agents.
CAN I DO SPOT SPRAYING?
The shut-off valve on the Solo sprayer is well suited for
spot spraying. It’s almost effortless! The shut-off valve
handle incorporates a clip which holds the valve open for
area spraying without tiring the operator’s hand. A pressure
gauge may be added with increments from 0 to 6 Bar
(0-90 psi).
3
Note: Always wear rubber gloves, safety goggles and appropriate protective clothing when repairing a sprayer.
Once a repair is completed, fill the unit with clean water, pressurize, and check for leaks. If the sprayer leaks,
DO NOT USE. Repair leaks and re-check.
SERVICE AND REPAIR SECTION
HANDHELD SPRAYER TROUBLE SHOOTING GUIDE
PROBLEM
CAUSE
SOLUTION
Difficulty in moving pump handle
• dirty cylinder wall
• remove piston, clean, grease and replace
• O-ring on piston swollen (not cleaned properly)
• replace O-ring, grease
Low pressure & resistance during pumping
• No lube on piston/cylinder
• lubricate with heavy grease
• Chemical in cylinder
• Replace umbrella valve
• Damaged O-ring in pressure relief valve
• replace O-ring
• worm or damaged O-ring in shut-off valve
• replace O-ring
• tank cap not tight
• tighten cap
Leaks from end of spray wand
• worn or damaged O-ring in shut-off valve
• rebuild shut-off valve
Leaks from inside cylinder
• no lube on piston cylinder
• lubricate piston, O-ring and cylinder
Leaks under cap
• worn or damaged umbrella valve
• replace umbrella valve
at bottom of cylinder
Leaks from shut-off valve
• damaged or missing gasket
• replace gasket
Leaks from hose
• screw cap not tight
• tighten tank cap
Pressure relief valve sticks
• worn, damaged or loose fittings, • tighten fittings and replace lack of lubrication worn parts, disassemble and lubricate O-rings
Air leak - air coming out between
• worn, damaged or loose fittings
• tighten fittings and the two.......
halves of the pump support replace worn parts
• lack of lubrication or contaminated
relief valve relief valve assembly
• clean and lubricate pressure • tighten tank cap
• tank cap not tight
• gasket twisted or lacking lubrication
• straighten gasket and lubricate with grease
• tank lip damaged
• repair or replace tank
accessories:
The following accessories are not standard. Order them from your Solo dealer.
Pressure control gauge (#49 00 322):
displays spraying pressure so operator
can maintain desired pressure level.
2-nozzle spray boom (#49 00 514): handheld
spray boom mounts on end of spray wand
(total width 33”; distance between nozzles 24”).
Includes 2 flat spray nozzles.
Pressure limiting valve (#49 00 183):
limits pressure to 5 psi, 10 psi or
15 psi as needed for low pressure
applications.
Double nozzle (#49 00 477): this is a multipurpose nozzle that attaches to the end of the
spray wand for double row application.
Brass adjustable spray nozzle
(#06 10 410-P): affords operator a full
range of sprays from fine to jet stream.
Brass spray wand (#49 00 528): The 2 pcs
spray wand is 60” (150 cm) long and replaces the
standard spray tube for treating trees up to heights
of 16 ft. (5 meters). Additional extension tube
available in 20” length (#49 00 513).
Drift guard (#49 00 430):
helps control application of formula
under breezy conditions.
Controlled Flow Valve (CFValve™): Provides
constant pressure and flow to the spray nozzle
and can be used in various applications.
4
Nozzle Tip Specifications
Description
Order number
Spray
volume
Pressure
Angle
US gal at
1/min /min atm
psi
Flat Spray nozzle
4074263
0.88
1.25
1.53
.23
.33
.40
1.0
2.0
3.0
15
29
44
120°
120°
120°
Flat spray nozzle
0.46
0.64
0.78
.12
.17
.21
1.0
2.0
3.0
15
29
44
80°
80°
80°
1.53
0.76
.40
.20
2.8
2.8
40
40
Straight stream
Hollow cone
-brass
0065210
-plastic with
0065132
stainless
steel insert
Applications
area and row treatment
Adjustable nozzle -brass
-plastic
4900207
4900527
tree spraying (adjustable spraying pattern)
Full cone nozzle
0065212
30°-50°
game repellents of high viscosity
Full cone nozzle
0065213
30°-50°
game repellents of low viscosity
Full cone nozzle
0065214
game repellents
Hollow cone nozzle
4900209
1 mm orifice
0.4
0.55
.10
.15
1.0
2.0
15
29
Hollow cone nozzle
4900252
1.4 mm orifice
0.64
0.91
1.11
.17
.24
.29
1.0
2.0
3.0
15
29
44
50°
65°
65°
Hollow cone nozzle
4900322*
1.8 mm orifice
0.88
1.25
1.53
.23
.33
.40
1.0
2.0
3.0
15
29
44
55°
70°
72°
No-drift nozzle
AN 0.5
4074383
0.23
.06
1.0
15
90°
No-drift nozzle
4074385
AN 1.0
0.28
0.38
0.46
.07
.10
.12
0.4
0.7
1.0
6
10
15
100°
100°
100°
No-drift nozzle
4074386
AN 2.0
0.55
0.76
0.91
.15
.20
.24
0.4
0.7
1.0
6
10
15
100°
100°
100°
Non-drift nozzle
4074514
AN 2.5
0.72
0.95
1.14
.19
.25
.30
0.4
0.7
1.0
6
10
15
110°
110°
110°
No-drift nozzle
4074513
AN 5.0
1.80
1.90
2.28
.48
.50
.60
0.4
0.7
1.0
6
10
15
120°
120°
120°
Foam nozzle
4900397
0.76
0.90
1.01
1.10
.20
.23
.26
.29
3.0
4.0
5.0
6.0
The XAN 2 nozzle is suited for low drift and
45
water saving application of herbicides which
60
tend to foam
75
5
90
shrubs, bushes
mainly for herbicides at low pressure
PARTS BREAKDOWN
Pos.
No.
1
-
-
2
3
4
5
6
7
10
-
11
12
-
13
14
15
16
17
18
19
20
21
21A
22
23
24
25
26
27
28
29
33
47
48
49
52
Pos.
No.
Prices and technical specifications are subject to change without notice.
SOLO LIMITED WARRANTY
-
25
30
34
35
41
42
43
44
45
50
53
Order
No.
For
Model
4071262
456
4071267
454
4071263
457
4800185
0062166
*
0062115
*
4300245
4073835
0062264
*
4073528
4073111
HD
4074387
4073834
4073834
4061345
*
4074656
*
0062165
*
4900515
***
4800170
4074295
0062144
*
4900230
4900645 456SW
0062271
0062258
4074527
0094308
*
4074283
0062106
4074756
4074755
4074148
4074329
4074263
4074336
4074335
0610402-K
4900527
4900207 456SW
Description
Tank, 2 gallon
Tank, 1 gallon
Tank, 3 gallon
Pressure relief valve assy.
O-ring
O-ring
Carrying strap
Pump piston, solid
O-ring
Tank cap, red
Tank cap, black
Cylinder support (need 2)
Cylinder
Cylinder (use with 0094308)
Gasket
Valve cone
O-ring
Pressure hose, assy.
Shut-off valve, assy.
Pin retaining
O-ring
Wand, assy. (inc. 35 & 21A)
Stainless Wand
O-ring
O-ring
Elbow
Umbrella valve
Filter
O-ring
Swirl plate
Jet cap tip
Retaining nut
Lock clip
Flat spray nozzle
Retaining nut
Lever
Shut-off valve repair kit
Plastic adj. nozzle (incl. a & b)
Brass adj. nozzle
Accessories
Order
No.
For
Model
4900405-K
0062106
HD
4074726
**
2700316
HD
4074337
0062249
4074338
4065189
4900430
4900622
0062115
HD
0065210
HD
Description
Pump repair kit
O-ring
Hollow cone nozzle
No drip check valve
Retaining nut
O-ring
Retaining nut
Pressure gauge guard
Drift guard
Pressure gauge assy.
O-ring
Brass flat spray nozzle
* Pump repair kit ** Organic liquid spray kit
***Cut pick-up tube to fit for models 454 and 456
Solo Incorporated guarantees the original purchaser of Solo equipment, that any failure of Solo
manufactured parts due to defects in material and workmanship occurring during the applicable
warranty period will be repaired or replaced without charge for parts or labor, except for those items
not covered by warranty.
CONSUMER LIMITED WARRANTY: Solo equipment purchased for consumer use is covered by this Limited Warranty
for a period of FIVE (5) YEARS.
COMMERCIAL LIMITED WARRANTY: Solo equipment purchased for commercial use is covered by this Limited Warranty for
a period of ONE (1) YEAR.
OPERATOR’S OBLIGATION AND RESPONSIBILITY: proof of purchase must be provided by the owner in order to obtain
warranty service. Should any failure covered by this Limited Warranty occur, deliver or ship the Solo products or parts to an
authorized Solo service center. Freight, packing and insurance costs, if any, will be borne by the owner. Follow normal maintenance
service to include applicable lubrication, operation and storage of the product as explained in the owner’s manual.
ITEMS NOT COVERED BY WARRANTY: provisions of the Limited Warranty will not apply to the following: Any indirect or
consequential damages that may result from the failure or malfunction of the Solo product. Normal service requirements arising
during the warranty period, such as cleaning, normal wear, lubrication, filter, spray tips, etc. Normal service work over and above
the repair or replacement of defective parts. Any failure that results from an accident, customer abuse, normal wear, neglect or
failure to operate the product in accordance with the instructions provided in the operator’s manual or provided with the product.
When an alteration or modification has been performed on a Solo product, Solo is responsible only for products as originally
furnished by Solo, provided the alterations or modifications do not adversely affect the product’s operation, performance or
durability. Parts or accessories that are incomplete with the product are not approved by Solo.
Full disclosure of Solo’s Limited Warranty is available from your local Solo dealer or Solo Incorporated, 5100 Chestnut Avenue,
Newport News, Virginia 23605.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
6
ORDER FORM
Order parts and accessories from your Solo dealer. If there is no local dealer, use this form to order from Solo.
Item Names/Description
Nozzles
Flat spray nozzle - surface area & row treatment
Jet cap
Swirl plate
Filter - standard
Sprayer elbow and nozzle assortment
No-drift wide angle flat nozzles - .60 GPM
mainly for spraying herbicides at low pressure. .30 GPM
At 15 psi they deliver:
.24 GPM
.12 GPM
Elbow nozzle assembly
Double spray nozzle - for double row application
spraying in two directions simultaneously.
Brass adjustable spray nozzle kit - with O-ring and screw
cap for tree spraying (from fine misting to a jet stream).
Brass adjustable spray nozzle (same nozzle as kit above)
Plastic adjustable nozzle
Hollow cone nozzles - for shrubs & bushes:
1.4 mm
1.8 mm
Jet stream nozzle
Foam spray nozzle - for low drift & water saving
application of herbicides which tend to foam.
No drip check valve - prevents spray tip from leaking when not in use.
Nozzle assortment - includes flat, hollow cone, no drift,
and plastic adjustable nozzles.
Extension tubes and spray wands
6” bendable spray wand
20” spray wand
20” extension tube
21” stainless steel wand
20” brass spray wand
27” spray wand
40” brass telescoping wand
48” carbon fiber wand
60” brass spray wand
4’ to 8’ Carbon Fiber Wand
Note: extension tubes attach to wands to extend length.
Spray wands attach to shut-off valve only.
Part No.
Retail Price
40 74 263
40 74 755
40 74 756
40 74 283
06 10 408-P
40 74 513
40 74 514
40 74 386
40 74 385
49 00 258N
49 00 477
2.00
1.50
1.50
2.56
14.95
2.50
2.50
2.50
2.50
6.35
24.95
06 10 410-P
8.75
Qty.
Total
49 00 207
49 00 527
49 00 252
49 00 322
40 74 758
49 00 397
6.25
4.25
2.85
2.85
1.50
9.95
27 00 316
4.95
06 10 456-P
12.95
49 00 450
49 00 230
49 00 513
49 00 645-P
49 00 421
49 00 319
49 00 478
49 00 449
49 00 528
49 00 445
18.95
9.95
13.50
11.95
12.95
13.50
29.95
35.95
29.95
69.95
49 00 514
31.95
49 00 298
79.95
9850
2.95
Spray booms
Spray booms - spray 2 or 4 rows at once with:
2-nozzle spray boom - handheld (total width 33”)
distance between nozzles 24”. Includes 2 flat spray nozzles
4-nozzle spray boom - mounts on rear of sprayer
(total width 49 3/4”; distance between nozzles 16”).
Includes 4 hollow cone nozzles.
Specialty items
Solo Superior grease
Pressure gauge kits - indicates spray pressure.
49 00 622
17.75
Use with shut-off valve 4800170. Fits all models.
Pressure limiting valve - for no-drift spraying of herbicides. Helps operator maintain pressure below 15 psi.
49 00 183
18.95
Interchangeable springs are color coded for 5, 10 and 15 psi.
Drift guard - complete control for herbicide applications in
49 00 430
16.95
berry, flower, vegetable, cotton & other applications.
Shut-off valve
48 00 170
14.75
Shut-off valve, wand & elbow nozzle assy.
49 00 170N
19.95
Pump repair kit - contains original equipment O-rings to renew 49 00 405-K
5.95
all sealing surfaces on 454, 456, 457 sprayers
Shut-off and pump repair kit
0610411-K
9.95
Sprayer service video
998SPVID
9.95
454/456/457 Operator's Manual, Spare Parts List
US9456702
NC
NC
SUBTOTAL
Prices and technical specifications are subject to change without notice.
7
$
PARTS BREAKDOWN
Pos.
No.
1
-
-
2
3
4
5
6
7
10
-
11
12
-
13
14
15
16
17
18
19
20
21
21A
22
23
24
25
26
27
28
29
33
47
48
49
52
Pos.
No.
-
25
30
34
35
41
42
43
44
45
50
53
Order
No.
For
Model
4071262
456
4071267
454
4071263
457
4800185
0062166
*
0062115
*
4300245
4073835
0062264
*
4073528
4073111
HD
4074387
4073834
4073834
4061345
*
4074656
*
0062165
*
4900515
***
4800170
4074295
0062144
*
4900230
4900645 456SW
0062271
0062258
4074527
0094308
*
4074283
0062106
4074756
4074755
4074148
4074329
4074263
4074336
4074335
0610402-K
4900527
4900207 456SW
Description
Tank, 2 gallon
Tank, 1 gallon
Tank, 3 gallon
Pressure relief valve assy.
O-ring
O-ring
Carrying strap
Pump piston, solid
O-ring
Tank cap, red
Tank cap, black
Cylinder support (need 2)
Cylinder
Cylinder (use with 0094308)
Gasket
Valve cone
O-ring
Pressure hose, assy.
Shut-off valve, assy.
Pin retaining
O-ring
Wand, assy. (inc. 35 & 21A)
Stainless Wand
O-ring
O-ring
Elbow
Umbrella valve
Filter
O-ring
Swirl plate
Jet cap tip
Retaining nut
Lock clip
Flat spray nozzle
Retaining nut
Lever
Shut-off valve repair kit
Plastic adj. nozzle (incl. a & b)
Brass adj. nozzle
Accessories
Order
No.
For
Model
4900405-K
0062106
HD
4074726
2700316
HD
4074337
0062249
4074338
4065189
4900430
4900622
0062115
HD
0065210
HD
Description
Pump repair kit
O-ring
Hollow cone nozzle
No drip check valve
Retaining nut
O-ring
Retaining nut
Pressure gauge guard
Drift guard
Pressure gauge assy.
O-ring
Brass flat spray nozzle
* Pump repair kit
***Cut pick-up tube to fit for models 454 and 456
Prices and technical specifications are subject to change without notice.
Mail or Fax to: Solo • 5100 Chestnut Avenue
Total from Previous Page
$
Newport News, VA 23605 • Phone: (757) 245-4228 • Fax: (757) 245-0800
VA & NC residents add applicable sales tax $
Order Online: www.solousa.com E-mail: [email protected]
Please do not send cash with this order. Make check or money order payable
to Solo Incorporated. You may request C.O.D. shipment. Please call for
current C.O.D. charges.
Form of Payment:
❑ Credit Card
❑ Check or Money Order
❑ C.O.D.
Shipping
$ 7.95
Grand Total
$
Please allow 1-2 weeks for delivery
Credit Card Number
Expiration Date
Signature and Phone Number
We cannot process your credit card purchase without a signature and expiration date.
PLEASE PRINT:
Name__________________________________________________________________
Address________________________________________________________________
City_ _______________________________________ State_______ Zip ___________
5100 Chestnut Avenue
Newport News, VA 23605
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement