Black & Decker | FP1610 | Instruction manual | Black & Decker FP1610 Instruction manual

384282/6121/JUN97
5/2/02
2:00 PM
Page 2
Black & Decker (U.S.) Inc. • 701 East Joppa Road, Towson, Maryland 21286
1997
JUN97-CD-1
Printed in U.S.A. (MAR95-CD-1)
Form No. 154428
384282 Copyright © 1995
384282/6121/JUN97
5/2/02
2:00 PM
Page 3
TM
Instruction Manual
6121
Right Angle
Random Orbit Sander/Polisher
384282/6121/JUN97
5/2/02
2:00 PM
Page 4
Getting the most out of your tool.
Please take time to read this manual and pay particular attention to the safety
rules we’ve provided for your protection. If you have any questions about
your tool please call:
1-800-9-BD TOOL
(1-800-923-8665)
Important Safety Instructions
WARNING: When using electric tools, basic safety precautions should
always be followed to reduce risk of fire, electric shock, and personal
injury, including the following:
READ ALL INSTRUCTIONS
ON/OFF SWITCH
Double Insulation
Double insulated tools are constructed throughout with two separate layers
of electrical insulation or one double thickness of insulation between you
and the tool’s electrical system. Tools built with this insulation system are
not intended to be grounded. As a result, your tool is equipped with a two
prong plug which permits you to use extension cords without concern for
maintaining a ground connection.
SHROUD
1
TM
SPEED
CONTROL DIAL
ADAPTER
FOR YOUR SAFETY - ALL TOOLS
DUST BAG
NOTE: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT
PARTS. Repair or replace damaged cords.
SANDING PAD
Polarized Plugs
6121
6" Right Angle Random Orbit Sander/Polisher with Speed Control
Polarized plugs (one blade is wider than the other) are used on equipment
to reduce the risk of electric shock. When provided, this plug will fit into a
polarized outlet only one way. If the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
384282/6121/JUN97
5/2/02
2:00 PM
Page 1
Safety Instructions For All Tools
• EXTENSION CORDS. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table shows the correct
size to use depending on cord length and nameplate ampere rating. If in doubt,
use the next heavier gage. The smaller the gage number, the heavier the cord.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t
use power tools in damp or wet locations. Keep work area well lit. Do not use tool
in presence of flammable liquids or gases.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, and refrigerator enclosures.
• KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should be kept away from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or
locked-up place — out of reach of children.
• DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was
intended.
• USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavyduty tool. Don’t use tool for purpose not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in
moving parts. Rubber gloves and non-skid footwear are recommended when
working outdoors. Wear protective hair covering to contain long hair.
• USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.
• DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your
hand and it frees both hands to operate tool.
• DON’T OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep
handles dry, clean, and free from oil and grease.
• DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when
changing accessories, such as blades, bits, cutters.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be
sure switch is off when plugging in.
Minimum Gage for Cord Sets
Volts
120V
240V
Ampere Rating
More
Not more
Than
Than
0
6
6
10
10 12
12 16
Total Length of Cord in Feet
0-25
26-50
51-100
0-50
51-100
101-200
101-150
201-300
AWG
18
18
16
14
16
16
16
12
16
14
14
12
14
12
Not Recommended
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool
when you are tired.
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is damaged should be
properly repaired or replaced by an authorized service center unless otherwise
indicated elsewhere in this instruction manual. Have defective switches replaced
by authorized service center. Do not use tool if switch does not turn it on and off.
1
384282/6121/JUN97
5/2/02
2:00 PM
Page 2
ADDITIONAL SAFETY INSTRUCTIONS
•
•
•
•
•
Switch
(See Figure 2) To turn the unit on, slide the switch forward (the symbol “I”
will be visible.) To turn the unit off, slide the switch back (the symbol “O” will
be visible). Before plugging in the unit, make sure the switch is in the off
position.
Always wear eye protection and a respirator when sanding.
Clean your tool out periodically.
Sanding of lead based paint is not recommended. See page 5 for additional
precautions when sanding paint.
CAUTION: Some wood contains preservatives such as copper chromium arsenate (CCA) which can be toxic. When sanding these materials extra care
should be taken to avoid inhalation and minimize skin contact.
Do not operate the unit without the dust shroud.
Speed Control Dial
The speed control dial (5 incremental settings) allows you to increase or
decrease speed from 4000 - 6800 Orbits Per Minute. The optimal speed
setting for each application is very much dependent on personal preference.
You may want to experiment on a piece of scrap to determine what gives
you the best combination of finish quality and material removal rate for
your application. Generally, you will want to use a higher setting on harder
materials and a lower setting on softer materials. Material removal rate
increases as speed increases.
SAVE THESE INSTRUCTIONS
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC
means your tool may be operated only with alternating current and never
with direct current. A voltage decrease of more than 10% will cause loss of
power and overheating. All tools are factory tested; if this tool does not operate, check the power supply.
Figure 1
SANDING DISC
PAD
Figure 2
Attaching Sanding Discs (Figure 1)
ON
Your sander/polisher is designed to use 6" sanding discs with the 6 hole dust
extraction pattern. To attach paper to the pad:
1.
2.
3.
4.
5.
OFF
Turn off and unplug tool.
Turn the sander/polisher over so that the sanding pad is facing upward.
Clean dust from pad face.
Hold the pad with one hand to keep it from rotating.
With the other hand, align the holes and place disc directly on top of pad.
SPEED CONTROL DIAL
(SETTINGS 1-5)
2
384282/6121/JUN97
5/2/02
2:00 PM
Page 3
Dust Collection
Your sander/polisher comes equipped with a cloth filter bag to collect the
dust generated during sanding. To empty the dust bag, first turn off and
unplug tool. Firmly pull the bag off while holding the rubber boot (Figure 3).
Empty the bag (you may want to turn it inside out.)
1
Figure 3
NOTE: Never operate this tool unless the dust collection bag is in place.
Replacing Sanding Pad
When the pad becomes worn out, use the following procedure to replace
pad. (See Figure 4)
TORX HEAD
SCREWS
PAD
1 Turn off and unplug tool.
2. Remove 4 torx head screws from the bottom of the tool and remove the
pad.
3. Replace the pad and screws, making sure the CFS disc is aligned properly.
CFS DISC
Operation
ALIGN NOTCHES TO
THOSE IN SHROUD
A side handle has been provided with your unit and must be used for control.
The side handle can be screwed into either side of tool by first removing the
plastic screw, as shown in Figure 5.
Figure 5
Move the unit in long, sweeping strokes along the surface being sanded, letting the sander/polisher do the work.
Figure 4
NOTE: Excessive downward pressure on the tool while sanding actually
slows the removal rate and produces an inferior quality surface.
NOTE: Be sure to check your work often. This sander/polisher is capable of
removing material rapidly, especially with coarse paper.
TM
The random orbital action of your sander/polisher allows you to sand with
the grain or at any angle across it for most sanding jobs. To produce the
3
384282/6121/JUN97
5/2/02
2:00 PM
Page 4
best finish possible, start with coarse grit sandpaper and change gradually
to finer and finer paper. Vacuum and wipe surface with a tack cloth
between grit steps.
and clean up BEFORE eating, drinking or smoking. Articles of food, drink,
or smoking should not be left in the work area where dust would settle on
them.
ENVIRONMENTAL SAFETY
a. Paint should be removed in such a manner as to minimize the amount of
dust generated.
b. Areas where paint removal is occurring should be sealed with plastic
sheeting of 4 mils thickness.
c. Sanding should be done in a manner to reduce tracking of paint dust outside the work area.
CLEANING AND DISPOSAL
a. All surfaces in the work area should be vacuumed and thoroughly
cleaned daily for the duration of the sanding project. Vacuum filter bags
should be changed frequently.
b. Plastic drop cloths should be gathered up and disposed of along with
any dust particles or other removal debris. They should be placed in
sealed refuse receptacles and disposed of through regular trash pick-up
procedures.
During clean up, children and pregnant women should be kept away from
the immediate work area.
c. All toys, washable furniture and utensils used by children should be
washed thoroughly before being used again.
The rate at which the dust bag fills up will vary with the type of material being
sanded and the coarseness of the sandpaper. For best results, empty the bag
frequently.
When sanding painted surfaces, (see instructions below for additional precautions when sanding paint) you may find that the sandpaper loads up and
clogs with paint. A heat gun will work much better to remove paint before
sanding. FOLLOW ALL SAFETY INSTRUCTIONS IN HEAT GUN INSTRUCTION MANUAL.
Precautions To Take When Sanding Paint
1. Sanding of lead based paint is NOT RECOMMENDED due to the difficulty
of controlling the contaminated dust. The greatest danger of lead poisoning is to children and pregnant women.
2. Since it is difficult to identify whether or not a paint contains lead without
a chemical analysis, we recommend the following precautions when
sanding any paint:
PERSONAL SAFETY
a. No children or pregnant women should enter the work area where the
paint sanding is being done until all clean up is completed.
b. A dust mask or respirator should be worn by all persons entering the
work area. The filter should be replaced daily or whenever the wearer has
difficulty breathing.
NOTE: Only those dust masks suitable for working with lead paint dust
and fumes should be used. Ordinary painting masks do not offer this protection. See your local hardware dealer for the proper N.I.O.S.H.
approved mask.
c. NO EATING, DRINKING or SMOKING should be done in the work area to
prevent ingesting contaminated paint particles. Workers should wash
Application Notes
SANDPAPER - GRIT TYPES
Natural Abrasives:
Flint is the softest (Mohs’ Scale 7) of the common natural abrasives. It has a
tan color and is very inexpensive. (Mohs’ Scale is the mineral hardness
scale. It rates diamond at 15, the hardest, and talc at 1.)
Garnet paper is harder than flint (Mohs’ Scale 7.5) and is easily identified by
4
384282/6121/JUN97
5/2/02
2:00 PM
Page 5
its bright orange color. Even though it is not the hardest, the way the abrasive fractures gives you a good cutting edge for woodworking.
Emery, even though harder than garnet (Mohs’ Scale 9), has blunt edges
making it a poor sanding abrasive. Its primary use is for polishing metal.
Manufactured Abrasives
White Aluminum Oxide (AlO) is extremely hard (Mohs’ Scale 12) and durable
which makes it a great abrasive for use with the Random Orbit Sander.
“White” describes the particular way the abrasive is manufactured, not its
color. This abrasive is widely available and comes in a variety of colors due
to the increasing use of dyes. Stearate lubricants on the paper also enhance
performance by reducing heat and the rate at which the paper clogs.
Silicon Carbide (SiC) is the hardest abrasive (Mohs’ Scale 13) commonly
available next to industrial diamond but is not as tough as Aluminum Oxide
abrasives. This abrasive easily fractures and provides sharp faces to the
work throughout the life of the sanding paper. This “self-sharpening” feature
makes SiC an outstanding abrasive for material removal but limits its life.
OPEN COAT VERSUS CLOSED COAT
Abrasives are applied to the paper with glue. When the grit is large (say 60 or
80 grit) the percent of coverage is usually reduced to 60% to 70% of the
backing paper surface.This increases the life of the paper by reducing the
rate at which the paper clogs. This is called an open coat and almost the only
way you can buy sandpaper in heavier grits. With finer grits the grit is
applied at rates of 90% or more and are labeled closed coat. Since the dust
particle is much smaller the tendency of the paper to load up and clog is
greatly reduced.
GRIT SIZES
There are several grading systems used. The system most popular today is
sieve size. The number on the back of your sandpaper disc refers to the screen
size the particle can pass through. 120 grit paper for example will sift through
a screen with 120 holes per linear inch. Every square inch of screen has 14,400
holes (120 x 120). The higher the number the finer the particle size. Common
sizes are from 36 to 600 with the recent introduction of grit sizes up to 1200.
SANDING
THE BASIC RULES: Which ones to break and which ones not to.
Always start with the coarsest grit first. Don’t break this rule. The scratches
get smaller as the grit number gets larger and the quality of the finish generally improves. When you change grits be particular about cleaning the surface that you are finishing. An 80 grit particle floating on your work under
your 220 grit paper will leave 80 grit scratches. The best way to avoid this is
to vacuum the work and then carefully wipe down the work with a tack rag.
The random orbit sander/polisher action is equally applied across the grain
and with the grain. Since the scratch mark is small and random in all directions, the ability of the eye to see a scratch is greatly reduced.
Always wear a mask to avoid breathing the dust. NEVER BREAK THIS RULE.
We have engineered the tool to collect a majority of the dust created in the
sanding process but the tool does not capture it all. To improve the capture
rate use a vacuum but ALWAYS wear a dust mask.
SOME OTHER HINTS FOR A BETTER FINISH
A random orbit sander is much more aggressive than other similarly sized
orbital tools so you may want to consider the next finer grit when you start
to sand your project.
Since the random orbit action makes a short scratch, you may find that a
project doesn’t require as many grit steps. A lot of professional cabinet
makers only use 80, 120, and 150 grit on their work with satisfactory
results. If in doubt about how the finish will take to your sanded surface,
wipe the surface with some paint thinner. Defects will show up darker than
the surrounding wood.
Careful inspection of the work prior to the finishing operation may reveal
dents. Try to correct these problems by raising the dent (a hot iron and wet
rag will do this) or carefully sand a large area around the dent. If you vigor5
384282/6121/JUN97
5/2/02
2:00 PM
Page 6
ously sand the dent, you may create a cupped surface.
Spread a light coat of a good grade of polish, with a soft clean cloth or brush,
over a small area and apply the sander/polisher before the polish dries.
Without turning tool “ON,” grasp the tool and pick it up. Keep the tool away
from your body and turn the switch “ON.” Make sure you have a firm grip on
the handle and can operate the tool freely without forced effort or unnecessary pressure. When starting to polish, it is all right to have the polishing pad
resting squarely on the surface, but as the scum and film begin to work
loose, start tilting the tool so that the dry outer section of the polishing pad
comes in contact with the surface. If hazy spots still remain, apply a little
more polish and work out these spots. THE POLISHER AND PAD MUST BE
KEPT IN CONSTANT MOTION. THEY SHOULD NOT BE ALLOWED TO
REMAIN IN ONE SPOT. TO DO SO COULD DAMAGE THE PAINT.
When you are satisfied with the sanding job and you have finished sanding
with your finest grit, raise the grain by dampening the wood with a wet rag.
When the wood has dried and you are ready to apply the finish, resand
lightly to take off the wood fibers raised by the water. Vac and tack the surfaces and immediately apply the first coat of finish before the wood gets
dirty.
WOOD: Some important characteristics of wood
Hard grain and soft grain
Wood has hard grain and soft grain. Hard grain is typically the product of summer growth and soft grain the product of spring. All sanders will remove more
soft grain than hard grain and since the random orbit sander is more aggressive, it will remove it that much more quickly. Extended sanding on a piece of
fir for example, will produce a noticeably uneven finish. This is a good reason
to correct flaws before sanding.
A polishing pad will become discolored with use because it has picked up
“dead” pigment from the car surface. Excess dirt on the pad can often be
removed by lightly touching the pad to an edge of the car bumper while pad
is rotating. (The edge of a work bench or garage door will serve the same
purpose). When the pad becomes very dirty, remove it from the tool and
wash it in a warm water detergent solution. The pad can then be air dried.
POLISHING
When polishing, only a LOW speed setting should be used (settings 2–3).
Wash your car before power polishing it. Washing will remove loose dirt,
scum, road salt, etc. which could act as an abrasive and damage the paint.
Loose dirt, etc. will also clog the polishing pad and you will have to clean it
more often.
Polishing Tips
These instructions and suggestions will help familiarize you in the general
operation of POWER POLISHING. You will develop your own techniques
which will make the job easier and faster as you learn power polishing.
Proper practice is essential to successful use of your sander/polisher.
Start polishing with the roof, move to the hood, the fenders, the doors, etc.
in this way, the slight dust that may be thrown off into the air by the revolving
pad will not fall on completed sections, and the power cord will not be
dragged over completed portions. When the car has been completely polished, an additional high luster may be obtained if a few drops of water are
sprinkled on the surface and gone over quickly with the sander/polisher or a
clean dry cloth. (If a cloth is used, it is not necessary to rub—merely wipe.)
You should use utmost care when power polishing around or over sharp
objects and contours of a car body. It is very important to use the correct
pressure with constant motion while polishing various sections of an automobile body. For example, light pressure should be applied when polishing
over sharp raised edges of body panels, or over edges of the rain gutter
along the top.
6
384282/6121/JUN97
5/2/02
2:00 PM
Page 7
Since everyone does not use the same type of Power Polish, we recommend you clean and polish a test section on a flat area of the car FIRST.
From this test section, you can judge the strength or cleaning action of
your Power Polish. Remember, all Power Polish is not the same. Different
brands will react differently on various painted surfaces. Also, you are now
using a POWER POLISHER. This is entirely different from any hand application which you may have done before.
CAUTION: The use of any non-recommended accessory may be hazardous.
Cleaning Compounds
Abrasive Disc Assortment, 2 of each grade.
(Aluminum Oxide Open Coat).
7" Coarse (36 Grit). Pkg. of 4.
7" Medium (50 Grit). Pkg. of 4.
7" Fine (80 Grit). Pkg. of 4.
Replacement 7" backing pad with nut and washer.
If you need any assistance in locating any accessory, call 1-800-9-BD TOOL
(1-800-923-8665) or contact Black & Decker, Consumer Services
Department, P.O. Box 618, 626 Hanover Pike, Hampstead, MD 21074.
8" Foam Polishing Pad:
For applying and removing polish/cleaner/wax and buffing surfaces to a high
luster.
The general procedure for using cleaning compound is similar to that used
for polishing. Spread a light coat of a good grade of compound on the surface with a clean cloth or brush and apply the sander/polisher. USE CARE
TO KEEP THE PRESSURE LIGHT AND THE POLISHER IN CONSTANT
MOTION. Best results are obtained when the unit is operated with the pad
at a slight angle to work surface. Care should be taken in the amount and
coarseness (light, medium or heavy) of the compound used and the motion
and pressure exerted on the work surface.
CAUTION: THE ABOVE ACCESSORIES ARE RECOMMENDED FOR USE
WITH YOUR SANDER/POLISHER. THE USE OF ANY OTHER ACCESSORY
OR ATTACHMENT MIGHT BE HAZARDOUS.
Waxing
CAUTION: DO NOT USE STRING TIE POLISHING PADS WITH THIS
SANDER. EXTREME PERSONAL INJURY MAY RESULT IF FINGERS ARE
CAUGHT BY ROTATING STRING TIE.
Waxing will protect the finish you have achieved from cleaning and polishing your car. Hard paste wax should be applied by hand and removed with
the sander/polisher. Liquid waxes can be both applied and removed with
the tool. After the wax has been removed, use the sander/polisher and a
clean pad to bring out a high luster.
Lubrication
Self lubricating bearings are used in the tool and periodic relubrication is not
required. However, it is recommended that, once a year, you take or send the
tool to a service center for a thorough cleaning and inspection.
Accessories
Recommended accessories for use with your tool are available at extra cost
from your distributor or your local service center. Service centers are listed
in back of manual.
Cleaning
Keep your machine as clean as possible by wiping with a clean cloth and
blowing through it with air after every 5 hours of use. Don’t use harsh chem7
384282/6121/JUN97
5/2/02
2:00 PM
Page 8
icals or solvents to clean the tool. These chemicals could seriously damage
the engineering polymers used to construct your sander. If you typically
wrap the cord around the tool when you store it, leave a generous loop of
cord such that the strain relief does not bend. This helps prevent premature
cord failure.
Every B&D tool is of the highest quality.
If you wish to contact us regarding this product, please call toll
free between 8:00am and 8:00pm ET, seven days a week:
1-800-9-BD TOOL
IMPORTANT
(1-800-923-8665)
To assure product SAFETY and RELIABILITY, particularly for double insulated tools, repairs, maintenance and adjustment (excluding maintenance
described in this manual) should be performed by B&D service centers or
authorized service centers, using identical B&D replacement parts.
One Year Free Maintenance
All B&D tools for Industry and Construction are covered under a one year free
maintenance program where B&D will inspect your tool for safety and provide
necessary maintenance or repairs, including normal wear and tear parts, for
one year, FREE OF CHARGE.
Full Warranty
All B&D tools for Industry and Construction are warranted to be free of any
defects in materials or workmanship. Upon thorough examination of tool,
B&D will repair or replace, at our option, any product that is determined to be
defective.
Conditions
The service/safety check and the warranty do not apply to: repairs made or
attempted by anyone other than an authorized B&D service location; misuse,
abuse, neglect, improper application of the tool; missing parts; or normal wear
and tear (after first year of ownership). Please return the complete unit, transportation prepaid, to any B&D factory owned or B&D authorized service center
location (list provided with tool or see yellow pages under “Tools Electric”).
8
384282/6121/JUN97
5/2/02
2:00 PM
Page 9
YOUR POWER TOOLS MAY BE SERVICED AT THE FOLLOWING B&D SERVICE CENTERS.
ALABAMA:
Birmingham 35209, 2412 Green Springs Hwy.. . . . . . . . . . . . . . . 205-942-0538
Mobile 36608, 3831 Airport Blvd. . . . . . . . . . . . . . . . . . . . . . . . . . 205-343-6624
ALASKA:
Anchorage 99518, 910 West International Airport Rd. . . . . . . . . . 907-563-4664
ARIZONA:
Mesa 85202, 535 S. Dobson, Suite 7. . . . . . . . . . . . . . . . . . . . . . 602-461-1074
Phoenix 85013, 4501 N. 7th Avenue . . . . . . . . . . . . . . . . . . . . . . 602-279-6414
Tucson 85712, 4845 E. Speedway Blvd. . . . . . . . . . . . . . . . . . . . 602-323-3388
ARKANSAS:
Little Rock 72201, 519 W. Seventh St. . . . . . . . . . . . . . . . . . . . . . 501-372-3040
CALIFORNIA:
Anaheim 92806, 540 South State College Blvd.. . . . . . . . . . . . . . 714-772-4050
Chula Vista 91910, 309 Broadway . . . . . . . . . . . . . . . . . . . . . . . . 619-420-6350
Concord 94520, 1500 Monument Blvd., #C2 . . . . . . . . . . . . . . . . 510-682-4880
Fresno 93710, 5412 North Blackstone Ave. . . . . . . . . . . . . . . . . . 209-435-0810
Long Beach 90805, 2011 South St. . . . . . . . . . . . . . . . . . . . . . . . 310-422-5825
Los Angeles 90040, 4820 South Eastern Ave., Suite “L” . . . . . . . 213-720-1834
Riverside 92506, 6215 Magnolia Ave., Suite “B” . . . . . . . . . . . . . 909-787-9700
Sacramento 95825, 2033 Fulton Ave. . . . . . . . . . . . . . . . . . . . . . 916-972-9090
San Diego 92123, 9270 Clairemont Mesa Blvd.. . . . . . . . . . . . . . 619-279-2011
San Jose 95128, 1185 So. Bascom Ave. . . . . . . . . . . . . . . . . . . . 408-293-7350
San Leandro 94578, 15206 E. 14th St. . . . . . . . . . . . . . . . . . . . . 510-276-1610
Van Nuys 91411, 14920 Victory Blvd. . . . . . . . . . . . . . . . . . . . . . 818-787-5531
COLORADO:
Denver 80219, 1171 S. Federal Blvd.. . . . . . . . . . . . . . . . . . . . . . 303-922-8325
CONNECTICUT:
Orange 06477, 481 Boston Post Rd. . . . . . . . . . . . . . . . . . . . . . . 203-795-3583
Wethersfield (Hartford) 06109, 662 Silas Dean Hwy. . . . . . . . . . . 203-563-5800
DISTRICT OF COLUMBIA: Washington
Colmar Manor 20722, 4153 Bladensburg Rd. . . . . . . . . . . . . . . . 301-779-3808
Falls Church, VA 22046, 344 W. Broad St. . . . . . . . . . . . . . . . . . 703-533-7313
FLORIDA:
Ft. Lauderdale 33334, 799 E. Oakland Pk. Blvd. . . . . . . . . . . . . . 305-566-5102
Ft. Myers 33907, 5224 Bank Street . . . . . . . . . . . . . . . . . . . . . . . 813-278-1188
Jacksonville 32205, 920 Cassat Ave. . . . . . . . . . . . . . . . . . . . . . . 904-781-2253
Miami (North) 33168, 13345 N.W. Seventh Ave. . . . . . . . . . . . . . 305-681-6658
Miami (South) 33156, 12233 So. Dixie Hwy. . . . . . . . . . . . . . . . . 305-232-9497
Orlando 32803, 3807 E. Colonial Dr. . . . . . . . . . . . . . . . . . . . . . . 407-894-7011
St. Petersburg 33709, 5635 49th St., N.. . . . . . . . . . . . . . . . . . . . 813-525-0273
Tampa 33609, 3432 W. Kennedy Blvd. . . . . . . . . . . . . . . . . . . . . 813-872-8317
West Palm Beach 33415, 310 South Military Trail . . . . . . . . . . . . 407-689-3247
GEORGIA:
Atlanta (South) 30349, 5330 Old National Hwy. . . . . . . . . . . . . . . 404-762-8844
Smyrna 30080, 2550 Cobb Pkwy. . . . . . . . . . . . . . . . . . . . . . . . . 404-956-0869
Stone Mountain (Atlanta) 30086, 5723 Memorial Dr. . . . . . . . . . . 404-292-4714
HAWAII:
Honolulu 96819, 330 Sand Island Access Road . . . . . . . . . . . . . 808-847-7447
ILLINOIS:
Des Plaines (Chicago) 60018, 1277 South Elmhurst Rd.. . . . . . . 708-364-5220
Lincolnwood (Chicago) 60646, 6710 N. Crawford Ave. . . . . . . . . 708-673-0923
Lisle (West Chicago) 60532, 2950 Ogden Ave., Unit H . . . . . . . . 708-717-1075
Moline 61265, 4433 23rd Ave. . . . . . . . . . . . . . . . . . . . . . . . . . . . 309-762-3000
Oak Lawn (Chicago) 60453, 6343 W. 95th St. . . . . . . . . . . . . . . . 708-423-7212
Waukegan 60085, 39 S. Greenbay Rd. . . . . . . . . . . . . . . . . . . . . 708-249-4390
INDIANA:
Evansville 47710, 307 First Ave., Crescent Ctr. . . . . . . . . . . . . . . 812-425-4269
Hammond 46323, 7103 Kennedy Ave.. . . . . . . . . . . . . . . . . . . . . 219-845-5100
Indianapolis 46224, 5999 Crawfordsville Rd. . . . . . . . . . . . . . . . . 317-243-8308
IOWA:
Des Moines 50310, 3427 Merle Hay Rd. . . . . . . . . . . . . . . . . . . . 515-270-1340
KANSAS:
Wichita 67213, 155 S. West St. . . . . . . . . . . . . . . . . . . . . . . . . . . 316-943-1271
KENTUCKY:
Louisville 40213, 5211 Preston Hwy. . . . . . . . . . . . . . . . . . . . . . . 502-968-7100
LOUISIANA:
Baton Rouge 70815, 11859 Florida Blvd.. . . . . . . . . . . . . . . . . . . 504-272-8111
Harvey 70058, 2500 Lapalco Blvd.. . . . . . . . . . . . . . . . . . . . . . . . 504-366-8676
Metairie (New Orleans) 70002, 3504 N. Causeway Blvd. . . . . . . 504-837-2550
Shreveport 71108, 7710-7714 Jewella Rd. . . . . . . . . . . . . . . . . . 318-688-1553
MARYLAND:
Baltimore (East) 21205, 4712 Erdman Ave. . . . . . . . . . . . . . . . . . 410-485-5550
Baltimore (North) 21030, 29-31 Cranbrook Rd., Cockeysville . . . 410-666-5966
Baltimore (South) 21122, 8220 Ritchie Hwy., Pasadena . . . . . . . 410-647-8456
Colmar Manor 20722, 4153 Bladensburg Rd. . . . . . . . . . . . . . . . 301-779-3808
MASSACHUSETTS:
Brighton (Boston) 02135, 12 Market St. . . . . . . . . . . . . . . . . . . . . 617-782-6264
Seekonk 02771, 120 Highland Ave. . . . . . . . . . . . . . . . . . . . . . . . 508-336-6510
MICHIGAN:
Grand Rapids 49512, 3040 28th St., S.E. . . . . . . . . . . . . . . . . . . 616-949-8331
Lansing 48917, 3203 W. Saginaw Hwy . . . . . . . . . . . . . . . . . . . . 517-323-4181
Warren 48093, 27035 Van Dyke Blvd. . . . . . . . . . . . . . . . . . . . . . 313-756-6711
Westland (Detroit) 48185, 8067 North Wayne Rd. . . . . . . . . . . . . 313-427-1520
MINNESOTA:
Bloomington (Minneapolis-St. Paul) 55420, 9517 Lyndale Ave., S. . 612-884-9191
MISSOURI:
Kansas City 64111, 4324 Main St. . . . . . . . . . . . . . . . . . . . . . . . . 816-531-0629
St. Ann (North St. Louis) 63074, 3637 North Lindbergh Blvd. . . . 314-739-4661
St. Louis 63131, 12852 Manchester Rd. . . . . . . . . . . . . . . . . . . . 314-821-8740
NEBRASKA:
Omaha 68127, 4225 S. 84th St. . . . . . . . . . . . . . . . . . . . . . . . . . . 402-592-5666
NEVADA:
Las Vegas 89104, 3411 East Charleston Blvd. . . . . . . . . . . . . . . 702-641-6555
NEW JERSEY:
Cherry Hill 08034, 1444 E. Marlton Pike/Rte. 70 . . . . . . . . . . . . . 609-429-2822
Little Falls 07424, 1189 U.S. Highway 46. . . . . . . . . . . . . . . . . . . 201-256-9373
Union (Scotch Plains) 07076, 2520 Route #22 East . . . . . . . . . . 908-233-5665
NEW MEXICO:
Albuquerque 87110, 5617 Menaul Blvd., N.E. . . . . . . . . . . . . . . . 505-884-1002
NEW YORK:
Buffalo 14209, 881 W. Delavan Ave. . . . . . . . . . . . . . . . . . . . . . . 716-884-6220
Centereach L.I. 11720, 2061-63 Middle Country Rd. . . . . . . . . . . 516-737-4706
Elmhurst (New York) 11373, 77-20 Queens Blvd. . . . . . . . . . . . . 718-335-1042
Latham (Albany) 12110, 836 Troy-Schenectady Rd. . . . . . . . . . . 518-785-1867
Rochester 14623, 2969 W. Henrietta Rd.. . . . . . . . . . . . . . . . . . . 716-424-1310
Syracuse 13214, 3485 Erie Blvd., East . . . . . . . . . . . . . . . . . . . . 315-446-3086
Westbury L.I. (New York) 11590, 1061 Old Country Rd. . . . . . . . 516-997-6140
NORTH CAROLINA:
Charlotte 28205, 3007 E. Independence Blvd. . . . . . . . . . . . . . . . 704-374-1779
Greensboro 27407, 3716 High Point Rd. . . . . . . . . . . . . . . . . . . . 910-852-1300
Raleigh 27604, 2930 Capital Blvd. . . . . . . . . . . . . . . . . . . . . . . . . 919-878-0357
OHIO :
Cincinnati 45241, 2310 E. Sharon Rd. . . . . . . . . . . . . . . . . . . . . . 513-772-3111
Columbus 43227, 3975 E. Livingston Ave.. . . . . . . . . . . . . . . . . . 614-237-0461
Dayton 45409, 2898 S. Dixie Dr. . . . . . . . . . . . . . . . . . . . . . . . . . 513-298-1951
Mayfield Heights (East Cleveland) 44124, 5881 Mayfield Rd. . . . 216-449-2770
9
OHIO (CONT’D)
Parma Heights (Cleveland) 44130, 6483 Pearl Road. . . . . . . . . . 216-842-9100
Toledo 43607, 3231 Dorr St . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419-531-8921
OKLAHOMA:
Oklahoma City 73106, 1318 Linwood Blvd. . . . . . . . . . . . . . . . . . 405-232-7515
Tulsa 74145, 3120 S. Sheridan Rd. . . . . . . . . . . . . . . . . . . . . . . . 918-622-5666
OREGON:
Portland 97209, 1640 N.W. Johnson St. . . . . . . . . . . . . . . . . . . . 503-228-8631
PENNSYLVANIA:
Evans City 16033, 20808 Rt. 19 North . . . . . . . . . . . . . . . . . . . . . 412-779-9600
Harrisburg 17112, 6080 Allentown Blvd. . . . . . . . . . . . . . . . . . . . 717-545-0651
Lancaster 17601, 118 Keller Ave.. . . . . . . . . . . . . . . . . . . . . . . . . 717-393-5251
Philadelphia 19103, 333 N. 20th St. . . . . . . . . . . . . . . . . . . . . . . . 215-564-5520
Philadelphia (North) 19115, 9977-81 Bustleton Ave. . . . . . . . . . . 215-464-7771
Pittsburgh 15232, 5437 Baum Blvd. . . . . . . . . . . . . . . . . . . . . . . . 412-362-2700
Whitehall (Allentown) 18052, 2242 MacArthur Rd.. . . . . . . . . . . . 610-435-9544
Wilkes-Barre 18702, 759 Kidder Street . . . . . . . . . . . . . . . . . . . . 717-824-5704
PUERTO RICO:
Puerto Nuevo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 809-783-3535
RHODE ISLAND:
See Seekonk, MA
SOUTH CAROLINA:
Greenville 29607, 1557 Laurens Rd. . . . . . . . . . . . . . . . . . . . . . . 803-232-3038
TENNESSEE:
Chattanooga 37421, 6231 Perimeter Drive, Space E. . . . . . . . . . 615-894-5957
Knoxville 37917, 4118 N. Broadway. . . . . . . . . . . . . . . . . . . . . . . 615-688-0921
Memphis 38116, 1085 East Brooks Rd. . . . . . . . . . . . . . . . . . . . . 901-332-3444
Nashville 37211, 4811 Nolensville Rd. . . . . . . . . . . . . . . . . . . . . . 615-833-8277
TEXAS:
Amarillo 79106, 3008 West 6th Ave. . . . . . . . . . . . . . . . . . . . . . . 806-373-1531
Austin 78757, 6549 Burnet Rd.. . . . . . . . . . . . . . . . . . . . . . . . . . . 512-459-1133
Dallas 75229, 2257 Royal Ln.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 214-620-6655
El Paso 79915, 6822 Gateway East . . . . . . . . . . . . . . . . . . . . . . . 915-778-9769
Fort Worth 76111, 721 North Beach St. . . . . . . . . . . . . . . . . . . . . 817-831-3828
Garland 75043, 718 W. Centerville Rd. . . . . . . . . . . . . . . . . . . . . 214-686-9302
Houston 77022, 536 E. Tidwell Rd. . . . . . . . . . . . . . . . . . . . . . . . 713-692-7111
Houston (S.W.) 77025, 9319 Stella Link Blvd. . . . . . . . . . . . . . . . 713-664-3666
San Antonio 78201, 500 Culebra Ave. . . . . . . . . . . . . . . . . . . . . . 210-732-1221
Webster 77598, 100 East Nasa Rd. One . . . . . . . . . . . . . . . . . . . 713-338-4556
UTAH:
Salt Lake City 84115, 1541 S. Third West St. . . . . . . . . . . . . . . . 801-486-5828
VIRGINIA:
Falls Church 22046, 344 W. Broad St. . . . . . . . . . . . . . . . . . . . . . 703-533-7313
Hampton 23666, 3416 W. Mercury Blvd. . . . . . . . . . . . . . . . . . . . 804-826-9382
Norfolk 23513, 7631 Sewells Point Rd. . . . . . . . . . . . . . . . . . . . . 804-480-3333
Richmond 23222, 1424 Chamberlayne Ave. . . . . . . . . . . . . . . . . 804-649-9245
WASHINGTON:
Seattle 98108, 421 S. Michigan St. . . . . . . . . . . . . . . . . . . . . . . . 206-763-2010
Spokane 99208, N. 7011 Division St. . . . . . . . . . . . . . . . . . . . . . . 509-467-8190
Tacoma 98409, 2602 S. 38th St. . . . . . . . . . . . . . . . . . . . . . . . . . 206-473-6040
WEST VIRGINIA:
Charleston 25312, 1638 Sixth Ave. . . . . . . . . . . . . . . . . . . . . . . . 304-343-0289
WISCONSIN:
Milwaukee (Wauwatosa) 53226, 10424 West Bluemound Rd.. . . 414-453-4240
384282/6121/JUN97
5/2/02
2:00 PM
Page 10
ALBERTA
Edmonton T6E 6H6, 3845 99th St. . . . . . . . . . . 403-462-5005
BRITISH COLUMBIA
Vancouver V5M 3Y7, 1735 Boundary Rd. . . . . . 604-291-9942
MANITOBA
Winnipeg R3H OK3, 934 St. James St. . . . . . . .204-783-7294
NOVA SCOTIA
Halifax B3K 2A4, 6100 Young Street. . . . . . . . . .902-453-5090
ONTARIO
Brockville K6V 5W6, 100 Central Ave.. . . . . . . . 613-342-6641
Kanata K2L 1V3, 462 Hazeldean Rd #11 . . . . . 613-831-2332
Glencairn Plaza
London N6E 3A9, 981 Wellington Rd #6 . . . . . . 519-649-2407
Markham L3P 3J3, 9275 Hwy 48 Unit 12/13 . . . 905-472-6168
Mississauga L4X 1L3, 1480 Dundas St. E #7. . 905-277- 0011
North York M3J 3G5, 48 Kodiak Cres . . . . . . . . 416-635-6740
QUEBEC
Brossard J4W 1M6, 5840 Boul Taschereau . . . 514-462-4881
Montreal H1Y 1B4, 3061 Belanger . . . . . . . . . . 514-722-1021
FOR ADDITIONAL SERVICE LOCATIONS
CALL: 1-800-9- BD TOOL
10
Download PDF