WarmlyYours | TW-E3CP | Specifications | WarmlyYours TW-E3CP Specifications

Installation & Operation Manual for
WarmlyYours Towel Warmers
Thank you for choosing your finely crafted WarmlyYours Towel Warmer.
Now you can add luxury and comfort to your bathroom with the soothing
embrace of a warm towel or bathrobe upon stepping from the shower.
The radiant heat from the Towel Warmer warms your towel.
Included in this document are all necessary installation and operation
instructions. For model number, reference the location of the product label
as shown in Diagram A on page 11. If you encounter any difficulties while
installing your system, installation support is available by phone between
the hours of 8:00am - 5:30pm CST, Monday through Friday by calling
(800) 875-5285.
SAFETY INFORMATION
• Towel Warmers are designed to warm towels and bathrobes only and
should not be used for any other purpose.
• Never stand, sit on or hang on the Towel Warmer unit.
• Never allow children to play on or with the Towel Warmer.
• Make sure that the electrical circuit breaker is shut off at the main panel
before wiring or servicing your Towel Warmer.
• The Towel Warmer must be properly grounded.
• All wiring must be in accordance with the National Electrical Code and
should be performed by a licensed professional who is certified to do
electrical wiring.
• Never place your Towel Warmer inside a shower, sauna or steam room.
• Never attempt to warm more than 2 towels on the Towel Warmer at
a time. Overloading the Towel Warmer will cause the unit to become
extremely hot and may result in a burn if touched.
CLEANING INFORMATION
• Clean the Towel Warmer with a soft, non-abrasive, damp cloth while
warm. Once the Towel Warmer has cooled, lightly polish with a soft dry
cloth. Do not use abrasive cleaning powders, metal polish or chlorinebased cleaners on any part of the Towel Warmer.
INSTALLATION
This appliance must be installed in accordance with the instructions in the
manual and the NEC guidelines relating to electrical fixtures in bathrooms.
The Towel Warmer must be on a GFCI protected circuit and be wired by
a professional who is certified to do electrical wiring.
1
Affixing the Towel Warmer to the Wall
Step 1
Draw a diagram of the preferred location of the brackets and the
electrical connection on the Towel Warmer box to create a template
(see Step 2 for template instructions). At least two of the four
brackets must be attached directly to a stud.
Step 2
Create the template:
A. Attach brackets into desired positions on the Towel Warmer
(see pages 3-4 for bracket assembly for each model).
B. Place Towel Warmer on the box (or a large sheet of paper) and
lay on a flat surface with brackets facing downwards.
C. Mark the location of the following:
• the electrical collar
• the location of the brackets
D. Use the template as a guide to mark the wall with the correct
locations of the four brackets, ensuring the following:
• the electrical collar is lined up with the center of the
electrical box
• at least two of the brackets are lined up with a wall stud
• the Towel Warmer is level
Step 3
Install the brackets onto the wall. Use the drywall anchors that are
supplied for the brackets that are not being installed into a stud.
Refer to Appendices A1-A2 for the Rough-in Diagram for each
model.
2
Affixing the Towel Warmer to the Wall - cont’d
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16” on center construction. Your situation
may vary depending on your stud spacing.
WARNING:
Locations of electrical box and anchor points may vary. Measure all
dimensions prior to rough-in and installation.
Riviera
stud
16” (406mm)
stud
215/8” (550mm)
anchor point*
anchor point
21”
(532mm)
anchor point
anchor point*
4 7/8” (124mm)
electrical collar
electrical box†
†
Note: Electrical box must be securely attached to a stud.
* Note: Anchor points must be attached to a stud.
3
Affixing the Towel Warmer to the Wall - cont’d
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16” on center construction. Your situation
may vary depending on your stud spacing.
WARNING:
Locations of electrical box and anchor points may vary. Measure all
dimensions prior to rough-in and installation.
Portofino
stud
stud
16” (406mm)
anchor point
anchor point*
25 3/16”
(640mm)
16” (406mm)
anchor point
anchor point*
†
23/8”
(60mm)
electrical collar
electrical box†
Note: Electrical box must be securely attached to a stud.
* Note: Anchor points must be attached to a stud. Brackets on this
model only are adjustable and may allow mounting to both
sides of stud if construction is 16” on center.
4
Affixing the Towel Warmer to the Wall - cont’d
Step 4
Attach all four brackets to their desired positions on the Towel
Warmer. See pgs. 6-8 for bracket assembly instructions specific
to the model you selected.
Step 5
Lay the template on a flat surface and place the Towel Warmer on
top with brackets facing downwards. Mark the exact location of
the electrical collar connection and the brackets.
Step 6
Use the template as a guide to mark the wall with the correct
locations of the four brackets. Ensure that the electrical collar is
lined up with the center of the electrical box. Also, at least two of the
brackets must be lined up with a wall stud. Ensure that all anchor
points are clear of existing electrical or mechanical systems.
Step 7
Check to make sure that the Towel Warmer is level.
Step 8
Install the brackets into the wall. Use the drywall anchors that are
supplied for the brackets that are not being installed into a stud.
See pgs. 10.11 for Final Installation Instructions
5
Bracket Assembly Diagrams - Portofino
A
B
4x
4x
C
D
*
d
e f
g h
4x
4x
8x
4x
4x
4x
i
J
K
4x
1x
Portofino
a. 0002-52110-0000
Clamp, threaded, portofino, Chrome
b. 0002-52110-0001
Clamp, Non-Threaded, Portofino, Chrome
c. 0002-52110-0002
Bracket, Mounting, Potofino, Chrome
d. 0002-51500-0000
Anchor, Drywall, #6
e. 0002-50200-0000
Screw, 50mm, 6,coarse thread
f. 0002-52200-0000
Screw, machine, 30mm, 5
g. 0002-52200-0001
Screw, machine, 20mm, 5
h. 0002-52100-0000
Pad round, 10mm x 4mm
i. 0002-50710-0001
Cap, non-vented
j. 0002-50710-0000
Cap, vented
k. 0002-00400-0000
Washer, 18 x 7 x 1
l. AK02-52000-0000
Parts kit Assy., Portofino
6
3x
Bracket Assembly Instructions - Portofino
Step 1
Measure for position of brackets using the template if desired. At
least two brackets must attach to a stud.
Step 2
Affix part C to the wall using screw e and drywall anchor d* where
necessary.** Slot in C should face downwards.
Repeat Step 2 for the three remaining brackets.
Step 3
Insert rubber pads h (2x) into A and B. Clamp A and B around the
Towel Warmer horizontal bar with A on the top. Insert screw g and
tighten.
Repeat Step 3 for the three remaining brackets.
Step 4
Hang Towel Warmer on the brackets and fix in place by inserting
screw f.
* Drywall anchor need not be used when screwing into a stud.
** Actual drywall anchor may differ in appearance.
1.
2.
B
3.
A
4.
d
f
g
C
h
A
B
e
7
Bracket Assembly Diagrams - Riviera
A
B
G
1x
4x
H
4x
2x
c
d
e*
f
4x
4x
A
c
8x
1x
f
B
Riviera
a. 0002-51110-0000
Bracket, mounting, stainless steel, Riviera
b. 0002-51310-0000
Stud, threaded, mounting, stainless steel
c. 0002-50210-0000
Screw, set, 3mm
d. 0002-50900-0000
Wrench, hex key, 3mm
e. 0002-50500-0000
Anchor, drywall, gray, #8
f. 0002-50200-0000
Screw, 50mm x 8
g. 0002-50710-0000
Cap, vented (not shown)
h. 0002-50710-0001
Cap, non-vented (not shown)
AK02-53000-0000
Parts Kit Assy, Riviera
8
Bracket Assembly Instructions - Riviera
Step 1
Measure for position of brackets using the template if desired. At
least two brackets must attach to a stud.
Step 2
Affix part A to the wall using screw f and drywall anchor e* where
necessary.**
Repeat Step 2 for the three remaining brackets.
Step 3
Screw part B into the positions on the Towel Warmer.
Repeat Step 3 for the three remaining brackets.
Step 4
Hang Towel Warmer on the brackets by inserting part B into part
A, loosening the hex-head screws c with the hex-key d where
necessary.
* Drywall Anchor need not be used when screwing into stud.
** Actual drywall anchor may differ in appearance.
9
Diagram A.
Diagram B.
Label
O-ring
Diagram C.
Step 9
With the brackets now in place, slide electrical wires through rubber
O-ring on electrical plate. Refer to Diagram A. Do not remove
rubber o-ring from electrical plate under any circumstances.
Step 10
Adjust the Towel Warmer to desired position from wall and screw
the screws into place, but do not tighten at this time.
10
Final Installation Instructions (for all models) - cont’d
Step 11
Have a certified professional wire the Towel Warmer to the electrical
line according to code, referring to the detailed wiring diagram
provided in Appendix B.
Step 12
Push the wires into the electrical box and screw the cover plate to
the outside of the box.
Step 13
Screw the adjustable collar out and tighten it against the faceplate
on the electrical box, ensuring the rubber seal is in position and
sealed correctly inside the collar. Refer to Diagram B.
Step 14
Fully tighten the screws for the brackets.
Step 15
Switch on the power by touching the “on” button to confirm that
the control is operable. In approximately 10-15 minutes, your
Towel Warmer will be warm to the touch. Refer to Diagram C.
11
OPERATION
WarmlyYours Towel Warmers include our programmable timer for
luxurious and economical use of the Towel Warmer.
On
Towel Warmer runs at 100% power and
will reach temperatures between 100˚ F
and 140˚ F depending on the following:
running time, number of towels, type of
towels and ambient room temperature.
Automatic Mode
Programmable Timer allows up to 14
events or 2 ON-OFF cycles per day. Easy
programming allows you to set intervals
of operation for each day of the week.
Manual Mode
Timer can be set to operate in manual
mode to function as a simple ON-OFF
switch.
Your WarmlyYours Towel Warmer is designed to gradually warm
towels over the course of a day and works best when towels are
left to hang for at least 3 hours.
SPECIFICATIONS
Model
TW-R09BS-HW
TW-R09PS-HW
TW-OCP
Name
Voltage
Dimensions
(Volts)
Riviera -
24”w (600mm) x 32”h (790mm)
Brushed
x 5”d (120mm)
Riviera -
24”w (600mm) x 32”h (790mm)
Polished
x 5”d (120mm)
Portofino
24”w (600mm) x 32”h
Heat
Output
(Watts)
Resistance
Amperage
(ohms)
(amps)
120
150
96
1.25
120
150
96
1.25
120
140
90
1.17
120
N/A
N/A
N/A
(800mm) x 9”d (225mm)
TW-TIMER
Timer
2”w (51mm) x 4”h (102mm)
12
Product Construction - Towel Warmer
Depending on the model, the towel warmer is constructed from
high carbon steel or stainless steel with a wall thickness of
between 0.8 mm and 1.2 mm. The steel tubing is brazed together
with full, continuous joints. The finished assembly is electroplated,
polished, or brushed, depending on the model and style. The towel
warmer is heated with a heating element. The mounting brackets
are manufactured from steel and finished to match the finish of the
specific model.
Product Construction - Control
The Timer is humidity sealed to IEC standards for zone 1 (areas
where it may be splashed by water) and zone 2 (areas which are
occasionally subject to high humidity) and therefore suitable for
installation in damp locations such as bathrooms.
Connection Method
The heating wire is connected to a non-heated lead by a mechanical
crimp connection, sealed with a heat shrink tube. Electricity is fed
into the Towel Warmer via a threaded adjustable nipple. The nipple
is adjusted so that it fits securely to the front of 2”x4” electrical
junction box. This box is secured in the wall and a water resistant
seal is made with the use of a rubber O-ring. Power can then be
fed to the control unit which may be located anywhere in the room.
Safety Ratings
The main electrical line feeding the Towel Warmer must incorporate
an Appliance Leakage Current Interrupter (ALCI) for North
America.
13
WarmlyYours Towel Warmer Warranty
WarmlyYours.com Inc. warrants the WarmlyYours Towel Warmers (“the Product”)
to be free from defects in materials and workmanship for five years from the date of
sale, provided that the Product is installed in accordance with the accompanying
Installation and Operation Manual, and any special written design or installation
guidelines provided by WarmlyYours.com Inc. for this product, the National Electric
Code (NEC), and all applicable local building and electrical codes. Controls sold
under the WarmlyYours.com Inc. name are warranted for one year from the date
of sale.
Any suspected defect must be reported by registered letter immediately upon
discovery. The determination of such a defect must be made by WarmlyYours.
com Inc., or its authorized representative only. This warranty is null and void if the
product is improperly installed, improperly operated, or abused.
WarmlyYours.com Inc. assumes no responsibility under this warranty for any
damage to the product caused by any trades person, or visitor on the job site, or
damage caused as a result of post installation work.
Under this Limited Warranty, WarmlyYours.com Inc. will provide the following
remedy:
If the Product is determined to be defective in materials and workmanship, and
has not been damaged as a result of misuse or misapplication, WarmlyYours.
com Inc. will refund the original purchase price or replace the Towel Warmer, at
WarmlyYours.com Inc. expense. WarmlyYours.com Inc. will not be liable for the
labor required to replace the Towel Warmer.
The Limited Warranty is null and void if the project owner or his representative
attempts to repair the Product without receiving authorization. Upon notification
of a real or possible problem, WarmlyYours.com Inc., will issue an Authorization
to Proceed under the terms of the Limited Warranty.
WARMLYYOURS.COM INC. DISCLAIMS ANY WARRANTY NOT PROVIDED
HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WARMLYYOURS.COM INC. FURTHER DISCLAIMS ANY RESPONSIBILITY
FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT,
INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR
REPRESENTATIVE OF WARMLYYOURS.COM INC. HAS ANY AUTHORITY
TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR
MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.
Please fill in warranty card info at www.WarmlyYours.com/warranty/tw or call
(800) 875-5285 to register via phone.
14
Appendix A1: Rough-In Diagram - Riviera
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16” on center construction. Your situation
may vary depending on your stud spacing.
WARNING: Locations of electrical box and anchor points may vary.
Measure all dimensions prior to rough-in and installation.
2” X 4” STUD
(51mm x 102mm)
2” X 4” STUD
(51mm x 102mm)
PERMANENT 120V ac
FROM HOUSE POWER
16” (406mm)
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX
FOR TIMER
21”
(532mm)
1/2” (13mm) CONDUIT
4 7/8”
(124mm)
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX FOR TOWEL
WARMER CONNECTION
21 5/8”
(550mm)
MOUNT CENTER OFJUNCTION BOX
21 5/8” (550mm) TO THE RIGHT OF CENTER OF STUD
Note: Electrical box must be securely attached to a stud.
Note: Anchor points must be attached to a stud.
15
Appendix A2: Rough-In Diagram - Portofino
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16” on center construction. Your situation
may vary depending on your stud spacing.
WARNING: Locations of electrical box and anchor points may vary.
Measure all dimensions prior to rough-in and installation.
2” X 4” STUD
(51mm x 102mm)
2” X 4” STUD
(51mm x 102mm)
PERMANENT 120V ac
FROM HOUSE POWER
16” (406mm)
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX
FOR TIMER
25 3/16”
(640mm)
1/2” (13mm) CONDUIT
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX FOR TOWEL
WARMER CONNECTION
MOUNT CENTER OFJUNCTION BOX
2 3/8” (60mm) TO THE RIGHT OF CENTER OF STUD
Note: Electrical box must be securely attached to a stud.
Note: Anchor points must be attached to a stud.
16
Appendix B: Wiring Diagram (All models)
2” x 4” ELECTRICAL
BOX FOR TIMER
120 Volt TIMER
LINE
(black)
120 a.c. HOT
NEUTRAL
(white)
NEUTRAL
LOAD
(blue)
GROUND
BLACK
TOWEL WARMER
GREEN GROUND
WHITE
HOT
LOAD
(black or red)
NEUTRAL LOAD
(white)
GROUND
(green/yellow)
2” x 4” ELECTRICAL BOX
10073-J
Rev 9/11
18
Download PDF