GEOSATpro DSR200c Owner's Manual & Installation Manual

Document

Owners Manual

Installation Guide

Version 2010.07

DSR200c -

Standard Receiver

This manual contains operation and installation instructions for the GEOSATpro DSR200c standard satellite receiver and the

GEOSATpro DVR1100c satellite receiver with digital video recording capability.

The basic operation of both models are identical, but the DVR1100c offers several digital recording features that are not found on the basic DSR200c receive only model. The additional features of the

DVR1100c are noted in the menu features and operation guides.

DVR1100c -

Digital Video Recorder Ready

Attention Glorystar Customers:

Please review the Glorystar instructions beginning on page 29

Note: Save all original boxes, manuals, accessories and packaging materials in case it is necessary to return the merchandise.

Before unpacking or assembly of any item, review the warranty, exchange and refund policies provided by your reseller.

DTV Transition Notice

After June 12th, 2009, a television receiver with only an analog broadcast tuner will require a converter box to receive full power over-the-air broadcasts originating from a

United States broadcaster with an antenna because of the Nation’s transition to digital broadcasting. Analog-only TVs should continue to work as before to receive low power,

Class A or translator television stations, cable, satellite TV services, gaming consoles,

VCRs, DVD players, and similar products.

Information about the DTV transition is available from www.DTV.gov or 1-888-CALL-

FCC, and from www.dtv2009.gov or 1-888-DTV-2009 for information about subsidized coupons for digital-to-analog converter boxes.

This notice does not affect any programming received by this satellite set-top box. Your digital satellite receiver will continue to receive the digital satellite signals and provide the programming for display on both Analog Televisions and new DTV compatible monitors with composite, Component YUV or S-Video input connections.

This notice complies with Parts 15 and 54 of Title 47 of the Code of Federal Regulations:

15.124 DTV Transition Notices by Manufacturers of Televisions and Related Devices.

Important Installation Notice: The Federal Communications

Commission (FCC) has ruled that local government zoning and homeowner’s associations may not prevent the installation of satellite antennas one meter (39”) or smaller in diameter within a resident’s private use area, unless legitimate safety restrictions such as fire codes are in effect.

For More information: http://www.fcc.gov/cgb/satellite.html

Materials contained in this installation manual are the property of:

Satellite AV, LLC.

8801 Washington Blvd., Suite 101

Roseville, CA 95678

http://www.satelliteav.com

Important Safeguards

Receiver Front / Rear Panel

Remote Control Layout

Basic Remote Operation

Receiver Operation Guide

Receiver Menu Items

DVR1100c Operation

DSR200c / DVR1100c Specifications

Page

Glorystar Installation Guide

Parts List

Site Survey

Dish Mounting Options

Dish Assembly

Universal Post Mount Assembly and Install

LNBF Bracket Assembly

Dish Aiming

Connect Receiver to a TV

Receiver Connection Examples

Activating the Glorystar Receiver

Locate and Peak Satellite Signal

Switch Installation - Single Room

LNBF Adjustments - (optional)

Updating Receiver and Channel List

Advanced / Hobbyist Installation

Using Satellite Meters

Completing the Install and Grounding

FAQ - Frequently Asked Questions

Accessories

Satellite Elevation Finder

29

54

B. Gohl

GEOSATpro

Important Safeguards

3 www.geosatpro.com Toll Free 888-483-4673

Example of Antenna Grounding

NEC, ANSI/NFPA 70

Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. Modification to the hardware or software without authorization by the manufacturer the will result in voiding any warranty. Service assistance may be arranged by contacting your reseller.

Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

B. Gohl

GEOSATpro

DSR200c / DVR1100c Specifications

MPEG Transport Stream & AV Decoding

Transport Stream

MPEG-2 ISOIIEC 13818 / Transport Stream Specification

Profile Level

MPEG-2 MP@ML

Input Rate

Max. 90 MbiU

Video Resolution

720 x 480 (NTSC)

Audio Decoding

MPEG / Musicam Layer I & II

Audio Mode

Single channel / Dual channel Joint Stereo / Stereo

Teletext

Sampling Rate

VBI & OSD / Closed Captioning pass through, EIA-608 compliant

32, 44.1 and 48KHz

Conditional Access Module Interface

SMART CARD

1 SLOT, ISO 7816, GSM11.11 and EMV (payment systems) compatibility

Tuner & Channel

Input Connector

F-type (Output loop-through), IEC 169-24, Female

Signal Level

-25 to -65 dBm

LNB Power / Polarization Vertical: +13.5 ±5

Horizontal: +18.5Vdc ±5% Current : Max. 500mA. Overload protected

22KHz Tone

DiSEqC Control

Data Interface

Frequency: 22KHz ±2KHz

Amplitude: 0.8 ±0.2V Version 1.0, 1.1, 1.2, USALS Compatible

Demodulation

Input Symbol Rate

SPDIF

QPSK

2-45 Ms/s Convolution Code Rate 112, 2/3, 3/4, 5/6, 7/8 with Constraint Length K=7

AV & Data Input/Output

RCA Output

CVBS (Yellow), L, R Output (White, Red) w/Volume, YUV Component, S-VHS (Y/C) Video

Dolby Digital Bitstream Out (Optical)

RS-232, Transfer rate 115Kbps, 9 pin D-Sub Male Type

USB: USB 2.0, Type A Connector 5V 1500mA / DVR1100c - Digital Video Record Function

RF Modulator

TV Standard

RF Connector

Frequency Range

NTSC

75 Ohms, F-type, Loop - through

VHF - CH3, CH4

System Resources

Main Processor

Flash Memory

Program DRAM

ARM946 Risc Processor

4 Mbyte

DSR200c - 16 Mbyte

DVR1100c - 32 Mbyte

Channel Capacity

Digital Channel: 5,000

Front

VFD Display (3 Icon, 5 digit Alphanumeric)

Power Supply

Input Voltage

AC 90 to 240V, 50 - 60Hz

Power Consumption

Protection

Net Weight

Max. 30W

Separate Internal Fuse

Type

SMPS

Physical Specification

Size (W x H x D) DSR200c - 260 x 50 x 210mm

DVR1100c - 290 x 50 x 220mm

2.0Kg www.geosatpro.com Toll Free 888-483-4673

DSR200c

Front Panel

Power Switch the receiver between Standby and Operation mode

Increase or Decrease the Volume

Change Channel Up / Down

Connects USB memory device for Firmware / Channel List upgrade

CAS Slot - Subscription card insertion with foil contacts facing down

DVR1100c

Front Panel

Power Switch the receiver between Standby and Operation mode

Display the Main Menu screens

Display the Channel List or enter an item in a menu

Change Channel Up / Down or move the cursor within a Menu

Increase or Decrease the Volume or move the cursor within a Menu

CAS Slot - Subscription card insertion with foil contacts facing up

B. Gohl

GEOSATpro

Rear Panel

Connects to the satellite dish coax cable

Loops the satellite signal to another satellite receiver

Connects composite VIDEO to TV or other equipment

Connects AUDIO Left / Right channels to TV or other equipment

Connects Component Video YUV to TV

Connects Optical Digital Audio to a digital audio amplifier

Connects S-VHS (Y/C) video to TV or other equipment

Connects to television antenna input (tune TV to channel 3 or 4)

Connects to an outdoor TV antenna or cable

Null Modem RS232 type computer connection for upgrade or repair

Connects USB 2.0 memory device for DVR / multi-media / upgrade of

Firmware or Channel List 5V/500ma

(DVR1100c Model only)

AC power plug connection (90 - 250VAC / 60Hz, 30W)

Master Power Switch disconnects receiver from external power

The GEOSATpro DSR200c & DVR1100c digital satellite receivers are Glorystar Approved.

www.geosatpro.com Toll Free 888-483-4673

Remote Control Unit

B. Gohl

GEOSATpro

Remote Key Functions DSR200c / DVR1100c

Switch the receiver between standby and operation modes

Display the Signal Strength and Signal Quality Meter

Select the Favorite Channel List mode

Display TV / Radio Electronic Program Guide (future Glorystar activation)

Display the Main Menu screens

Change channels or navigate the menu cursor

Increase or decrease the Volume

Select Alternative Language or additional audio tracks

Not Used

Return to Last Channel

Magnify an area of the screen (Zoom button 13 / 28, Position 6 / 21)

Mute or enable audio

Select all or one satellite for channel availability

Display the Information Program Banner on bottom of screen

Return to the previous menu or exit to normal viewing from menu

Display the Channel List or enter an item in a menu

Adjust volume, Navigate the menu cursor, DVR: Rapid FF / REW

Change channels up or down

Select Audio Mode Stereo, Mono Left / Right channel

Display Lyrics on Glorystar Karaoke Channel (future Glorystar service)

Enter manual timer setting in 24 hour mode

Select TV or Satellite for RF output

Page Up / Zoom increase magnification

Page Down / Zoom decrease magnification

Remote Key Functions DVR1100c

DVR: Scan Rewind in 2x, 4x, 8x, 16x, 32x speeds

DVR: Scan Forward in 2x, 4x, 8x, 16x, 32x speeds

DVR: Automatically rewind 30 seconds

DVR: Automatically rewind 5 seconds

DVR: Pause live or recorded TV and Radio programming

DVR: Start Record function

DVR: Stop Playback or Record function

DVR: View Recorded Program List or Resume Play function www.geosatpro.com Toll Free 888-483-4673

Basic Remote Operation

Place the satellite receiver in standby or operation modes, ON/OFF, using the Power button.

Change channels by either entering the channel on the numeric keypad or by pressing CHANNEL UP/DOWN buttons. Press the PREVIOUS

CHANNEL button to return to the last channel.

Adjust the volume by pressing the

VOLUME UP/DOWN buttons.

Volume is also controlled by the TV.

The satellite receiver volume should be set at mid-level and use the TV to adjust the volume.

Mute the volume by pressing the

MUTE button. Return to normal volume setting by pressing MUTE button or the VOLUME UP/DOWN button.

View a Programming Guide with program listings and descriptions by pressing the ELECTRONIC

PROGRAMMING GUIDE button.

View a program description of the selected channel (if available) by pressing the

INFORMATION button.

View a list of available channels by pressing the CHANNEL LIST/OK button.

View Signal Level (S) and Signal Quality (Q) of any channel by pressing the

SIGNAL button.

The receiver features many of the controls necessary for basic operation of the satellite system in case the remote is misplaced.

B. Gohl

GEOSATpro

Receiver Operation Guide

Channel Information

Program Information Banner

a) When selecting a channel, an information banner automatically appears on the bottom of the screen for a few seconds. This banner provides the current channel information.

e) f) g) c) d) b) b) Press INFO button to view the information banner during normal live viewing mode.

Detailed Channel List

a) Press List OK button during normal live mode to view a channel list

When a simple channel list is displayed on screen, press RED button to display a detailed channel list.

Press Navigation VOLUME UP/DOWN to sort alphabetically.

Press SAT button to sort by satellite and

FAV button for Favorites List.

Press Green button to return to All Channel mode or EXIT to return to the live channel.

Press YELLOW button to sort by ascending or descending alphabet, free, encryption type, or locked channels. Once sorted, press

YELLOW button to unsort.

Press BLUE button to enter the BISS code for cardless subscribed viewing of

BISS encrypted scrambled events. Check with the event coordinator or pay service provider to obtain the unique code. b)

Simple Channel List

a) Press List OK button during normal live mode to view a channel list

When a detailed channel list is displayed on screen, press RED button to display a simple channel list.

www.geosatpro.com Toll Free 888-483-4673

c) a)

EPG - Electronic Program Guide

Press EPG button during normal live mode.

An Electronic Program Guide will be displayed on the screen.

b) Select the desired channel.

Press OK once to view the channel in the preview window. Press OK a second time to go to the channel in live mode.

EPG -

DVR1100c

f) g) e) d) Select the program to watch or record.

Program information (if available) will be displayed in the upper right corner.

To set an event timer to Record, press the RECORD button once. A Red record symbol will appear in the EPG program title. The DVR will automatically record the program based on the program’s posted start and stop times. NOTE: An USB drive

must be attached and have enough space to complete the recording.

To set an event timer to view, press the

RECORD button a second time. A Green view symbol will appear in the EPG program title.

The receiver will automatically change to the selected program based on the program’s posted start time.

Press Exit to return to the current live channel.

Return to the Last Channel

a) Press Return button to recall the last channel selected.

Last Channel

Select Alternative Audio

a) Press AUDIO button.

b) Press the Navigation VOLUME UP/DOWN arrows to select an alternative audio (if available) for the current channel.

c) Press EXIT to save the selection.

Alternative Audio

B. Gohl

GEOSATpro

Stereo or Mono Audio Selection

a) b)

Press STEREO L/R button.

Press STEREO L/R button to toggle Stereo,

Left or Right Audio output for the current channel. Often a channel may program several audio sources together and a left or right channel must be selected.

c) Press EXIT to save the audio selection.

Stereo / Mono Audio

Zoom Function

Zoom IN / OUT

a) Press ZOOM button.

b) c) d)

Press PAGE UP button to increase the magnification or PAGE DOWN to decrease.

Press the Navigation VOLUME UP/DOWN arrows and the CHANNEL LEFT/RIGHT arrows to select the area to magnify.

Press EXIT to return to live channel.

Karaoke

Display Karaoke Lyrics

Feature not yet activated

Press KARAOKE button to display lyrics for available audio services.

Built-in A/B Switch

Select TV/VCR Output

Press ANT/SAT button to toggle the TV/VCR output on the rear of the receiver between the receiver’s satellite channels or any Cable TV, antenna or any source that is connected to the ANT input on the rear of the receiver. Perfect for connecting with Cable TV.

www.geosatpro.com Toll Free 888-483-4673

Signal Meter

View Signal Level and Signal Quality

a) Press the SIGNAL button to display a meter which shows Signal Level and Quality.

A Signal Level above 5% will indicate that a working

LNB is connected. The Signal Quality indicates the reception of the selected satellite and transponder. This advanced meter features a 10 bar graphic display of

Signal Quality sampled in .5 second intervals with a

5 second history. A high Signal Quality Reading with minimal ripple in the bar graph indicates optimal dish aiming and LNB placement. b) Press SIGNAL to exit the meter display.

Event Timer

•

Manual Event Timer Setup

a) Press TIMER button.

•

Number: Select event 1 - 10

Enable: Select YES to enable

Type: Select Once, Daily, Weekly

Channel: Select a TV or Radio channel

Month: Select month of the event

Date: Select the date of the event

Start: Enter the start time in 24 hour

mode. Example: Midnight is 00:00, 1:30pm

is set as 13:30.

DSR200c

•

Event Timer -

DVR1100c

Duration: Enter the length of the event.

Entering 00:00 will cause the receiver to

tune the channel, but not record

B. Gohl

DVR1100c

GEOSATpro

Receiver Menu Items

Main Page

Press MENU button and five Sub Menus will be displayed on screen

II.

III.

Channel Manager

Installation

Options

IV.

Utility

Accessory

I. Channel Manager

I-1.

I-2.

I-3

I-4

I-5

Organize Channels according to your preference. Note that changes made to the channels will be automatically updated to the most current Glorystar Channel list during the weekly OTA updates. To retain channel manager modifications, OTA Update must be disabled.

Press OK to display TV Channel Manager

Enter Password (default 0000)

Select Mode with Navigation buttons volume left or right arrow.

Press RED button to view channel

Press EXIT to return to previous menu or to go to the current live channel.

Favorite

Rename

Move

Lock

Delete

I-1. Favorite

Press MENU button and five Sub Menus will be displayed on screen

1. Press Navigation buttons volume left or right arrow to highlight FAVORITE 1-8.

Press OK on the channel to add or delete

A mark will appear on the selected channel

Press OK to add or delete.

Selected channels are automatically saved.

Press EXIT to return to previous menu or to go to the current live channel.

www.geosatpro.com Toll Free 888-483-4673

Press the Navigation button volume right to highlight RENAME.

Select channel to rename. Press OK.

Enter or edit the name using the keypad dialog screen.

Press YELLOW to rename Favorite 1-8.

Press BLUE to rename Satellite

Press EXIT to return to previous menu or

MENU to go to the current live channel.

I-2. Rename

I-3. Move

Press the Navigation button volume right to highlight MOVE.

Select channels to move by pressing OK.

Move cursor to the channel(s) new location.

Press GREEN to place the channel(s).

Press EXIT to return to previous menu or

MENU to go to the current live channel.

I-4. Lock

Press the Navigation button volume right to highlight LOCK.

Select channel to lock by pressing OK.

Press OK to lock the channel.

Press EXIT to return to previous menu or

MENU to go to the current live channel.

B. Gohl

Press the Navigation button volume right to highlight DELETE.

Press YELLOW button to toggle between single channel delete (CH), delete all channels on a transponder (TP) or delete all channels on a satellite (SAT).

Press OK to select a channel then BLUE button to delete individual channels in the

CH mode, all channels on a TP or all channels on a SAT.

Press EXIT to return to previous menu or

MENU to go to the current live channel.

I-5. Delete

GEOSATpro

II. Installation

This section will assist in configuring the unit to receive signals from the dish, control switches and enable a motorized dish. Scan for channels using Blind Scan, or using pre programmed transponders. Manually add, delete or edit transponders.

II-1.

II-2.

Channel Search Press OK. (Default 0000)

Red Button - TP Edit

Blue Button - Signal Beep ON / OFF

Motor Set-up Press OK. (Default 0000)

Red Button - TP Edit

Blue Button - Signal Beep ON / OFF

3. www.geosatpro.com

II-1. Channel Search

Satellite

- Press OK to display list of satellites

- Select the proper satellite. Press OK

DiSEqC / DiSEqC 1.1

- Press OK to list switch types

- Select the correct switch port. Press OK

TP Frequency

- Press OK to list programmed transponders

- Select an active transponder. Press OK

LNB

- Press OK list LNB LO type or frequency

- Select LO type or frequency. Press OK

22KHz

(may be controlled with LNB LO setting)

- Press OK to display ON / OFF

- Select the proper switch setting. Press OK

Multi-Dish Switch

- Press OK to display list of switch types

- Select the proper switch. Press OK

Search Options

- Press OK to display list of search types

- Select the desired search type. Press OK

Blind Scan searches and adds new transponders and channels

LNB Power

- Press OK to display list ON / OFF

- Select if to provide LNB power. Press OK

- If Signal Quality meter is displaying

Quality, Press OK to scan for channels.

Toll Free 888-483-4673

Motor Type

USALS is preferred way to install

- Press OK to display DiSEqC 1.2 / USALS

- Select the motor control method. Press OK

- If USALS, Press GREEN button and enter

the install location Longitude and Latitude.

II-2. Motor Setup

Satellite

- Press OK to list preprogrammed satellites

- Select the desired satellite. Press OK

Switch & LNBF

- Press OK to display switch / LNBF setups

- Change settings as needed. Press OK

TP Frequency

- Press OK to list programmed transponders

- Select an active transponder. Press OK

Motor Movement

- Press Navigate LEFT/RIGHT arrow to

move or bump the dish position East or West

Motor Control

- Press Navigate LEFT/RIGHT arrow to:

Store Sat Position: Stores current position

Goto Sat Position: Moves to stored position

Goto 0: Moves to motor 0 position

Reset Position: Resets motor stored settings

- Press OK to execute command

Satellite Position

Search Options

- Press OK to display list of Search Types

- Select the desired search type. Press OK

- If Signal Quality meter is displaying

Quality, Press OK to scan for channels.

Channel Search Completed

- Press OK to save found channels.

B. Gohl

GEOSATpro

II-1 & 2.b Transponder Edit

Press RED button to exit - no modification

Press Green button to add a transponder

Press YELLOW to delete a transponder

Press BLUE to manually add a channel when PIDs are available.

Press EXIT when completed. Press OK to save changes or highlight CANCEL and then press OK.

Freq Step

- Press OK to list 2, 4, 6, 8, 10MHz steps

- Select the step size. Press OK

Small steps provide detailed scans. Find more / take longer

II-1 & 2.c Blind Scan

Symbol Rate

>8000, 8000 - 4000, <4000, >4000

- Select the desired range. Press OK

Polarity

- Press OK to list All, Hor, Ver polarity

- Select the desired polarity. Press OK

Start Frequency

- Enter start IF between 950 - 2150MHz

The satellite tuner will scan the entire range unless modified.

If Blind Scanning with a Standard LNB LO, leave at 950

End Frequency

- Enter stop IF between 950 - 2150MHz

Standard LNB LO, enter 1450 (12.2GHz - 11.7GHz = 500MHz

Search www.geosatpro.com Toll Free 888-483-4673

III. Options

This section will assist in setting up the receiver with selected languages, time settings, RF output channel, screen size, parental security, etc.

III-1. OSD Setup

III-2. Control Panel

III-3. Time Adjust

III-4. Security

III-1. OSD Language

Highlight OSD (On Screen Display) Setup. Press OK

OSD Language

- Press OK to display list of OSD languages

- Select the proper Language. Press OK

Audio Languages

- Press OK to display list of languages

- Select a language for each priority.

Highlight OK, Press OK

Subtitle Language

- Press OK to display list of languages

- Select a subtitle language. Press OK

Display Information Banner

- Press OK to show list of display time-outs

- Select 2, 4, 6, 8, 10, 12 seconds. Press OK

OSD Position

positioning offsets.

- Select the proper positioning. Press OK

Screen Format

formats ratios

letterbox mode. Press OK

Channel History

B. Gohl

- Select the desired quantity. Press OK

GEOSATpro

III-2. Control Panel

Highlight Control Panel. Press OK.

1. RF Channel

sets TV /VCR output channel

- Press OK to display output channels 3 or 4

- Select the desired output channel.

Press OK

Closed Captioning

enables / disables feature

- Press OK to display ON / OFF

- Select correct mode, Press OK

EPG (Electronic Program Guide) Duration

display window listing.

- Select 60, 90, 120, 150, or 180 minutes.

Press OK

III-3. Time Adjust

Highlight Time Adjust. Press OK.

1. Auto Time Set

- Press OK to display time zones

- Select the correct time zone.

Press OK

synchronizes via the satellite.

If the receiver is activated in the Glorystar or Adventist modes, the time is synchronized with the Glorystar OTA updating transponder.

- Highlight Daylight Savings

- Press OK to display ON / OFF

- Select the correct time offset.

Press EXIT

Manual Time Set

overrides auto time set mode

Year

- Press OK to display list of years

- Select correct year, Press OK

Month

- Press OK to display list of months

- Select correct month, Press OK

Date

- Press OK to display list of dates

- Select correct date, Press OK

Hour

- Manually enter time in a 24 hour format.

Example: 1:30 pm = 13:30

Press EXIT www.geosatpro.com Toll Free 888-483-4673

Highlight Security. Press OK. Enter Password (default

0000)

1. Parental Lock

- Press OK to display ON / OFF

- Select Parental Control mode. Press OK

Parental Level

- Press OK to display list ratings

- Select the proper rating level. Press OK

Install Lock

- Press OK to display ON / OFF

- Select if install menu lock is ON / OFF

Press OK

New Password

- Enter new password

Confirm Password

- Reenter new password to confirm change

III-4. Security

IV. Utility

This section will assist in reviewing the system information, using the USB 2.0 functions with the DVR1100c, manually setting event timers and resetting the system.

IV-1. System Information

IV-2.a USB Firmware / Channels

IV-3.a Timer -

DSR200c

IV-3.b Time Record -

DVR1100c

IV-4. Factory Default

DSR200c

DVR1100c

IV-1. System Information

Highlight System Information. Press OK.

This screen provides information regarding the brand, model, software and firmware currently installed in the satellite receiver.

B. Gohl

GEOSATpro

IV-2. USB

Highlight USB. Press OK.

This menu shows all files that are saved on the connected USB drive.

1. File Loading

- Highlight correct file. Press OK

- Select S/W Upgrade, S/W + All Data

Upgrade or Boot Loader Upgrade as

specified in the text file provided with the

data or firmware file.

Do not load any file that is not provided by Satellite

AV or Glorystar specifically for the DVR1100c.

Loading an incorrect file can permanently damage the receiver and void the manufacturer warranty!

- Press OK to download the file.

Saving Channel List or settings

- Press GREEN button to select save mode.

- Select Channel Data or All S/W Data

- Press OK to save the data to attached USB

Deleting File

- Highlight file to be deleted

- Press BLUE button to delete file.

- Select OK. Press OK to confirm delete

Format the USB Drive

-Press YELLOW button to Format

- Select OK. Press OK to confirm Format.

IV-3.a Timer / Time Record

Highlight Timer / Time Record. Press OK.

Number

- Press OK to display event timers 1 - 10

- Select timer to program. Press OK

Enable

- Press OK to display YES / NO

- Select YES to enable. Press OK

Number

- Press OK to display event timers 1 - 10

- Select timer to program. Press OK

Type

- Press OK to display event frequency

- Select Once, Daily, or Weekly. Press OK

DSR200c

www.geosatpro.com Toll Free 888-483-4673

IV-3.a Timer / Time Record - cont.

Channel

- Press OK to display Channel list

- Select channel. Press OK

Month

- Press OK to display month

- Select month of event. Press OK

Date

- Press OK to display date

- Select date of event. Press OK

Start

DVR1100c

IV-3.b Time Record -

DVR1100c

Duration - DVR1100c Model

- Press EXIT

IV-5. Factory Default

Highlight Default. Press OK. Highlight OK then press

OK to confirm the resetting of the receiver back to the default setting.

Warning! A Factory Default will reset the receiver back to the factory settings and eliminate all scanned channels and reset all menu settings!

V. Accessory

This section will assist in setting up the receiver for Time Machine recording and defeating the automatic receiver updating via the satellite.

V-1.

V-2.

V-3.

B. Gohl

Time Machine -

DVR1100c

OTA

Smart Card

DSR200c

DVR1100c

GEOSATpro

V-1. Time Machine -

DVR1100c

Time Machine is an advanced feature on the DVR1100c that will record the current program that you are viewing or listening up to the maximum memory space reserved for the function when a USB drive is connected. Example 1GB provides approximately 1 hour of TV program record time. You may rewind, pause, skip backwards, forward or anywhere within this recording. A new recording begins when the channel is changed. The previous channel recording is recycled and will no longer be available for viewing. Disconnecting the USB will disable the feature.

Highlight Time Machine. Press OK.

- Press OK to display the USB drive space reserved for the Time Machine function.

512MB = 30 minutes, 1GB = 1 hour, 2GB = 2 hour, 3GB = 3 hours, 4GB = 4 hours

- Select Create. Press OK

V-2. OTA

These receivers can be manually updated with new features and firmware from a satellite. Glorystar channels are automatically added to the channel list.

This feature is automatically set to ON by default in the Glorystar mode. If you wish to control the updating process and update manually, turn the OTA feature

OFF.

Highlight OTA. Press OK.

- Select Automatic Update

- Press OK to display ON or OFF

- Select OTA Update feature ON or OFF

- Press OK to confirm and EXIT

To manually update the receiver with the newest firmware and or channel lists in the Advanced mode, your dish must be aimed at a satellite carrying the

GEOSATpro updating firmware service. Visit www.

GEOSATpro.com to locate the satellite servicing your region. Select UPDATE NOW and press OK to download.

Warning! OTA Firmware Updates will reload the factory settings, channel list and eliminate scanned channels and reset all menu settings! Save any custom channel lists to a USB drive before updating then reload after completion of the update.

V-3. Smart Card

Highlight Smart Card. Press OK.

This screen provides information regarding the reception of subscription based programming with a

CAS (conditional access card / smart card).

Insert the subscribed Smart Card:

DVR1100c - Foil contacts facing up

DSR200c - Foil contacts facing down www.geosatpro.com Toll Free 888-483-4673

DVR Operation

-

DVR1100c

DVR stands for Digital Video Recorder. Satellite TV and Radio programs can be recorded and played back on the TV with perfect digital quality using an optional

USB 2.0 drive. The maximum USB 2.0 drive capacity is 500GB and must be formatted to FAT32. If the drive is not formatted to FAT32, a software program called SwissKnife (www.compuapps.com) is available to format with a PC (MAC computers automatically format as FAT32). Always format a new drive with the

DVR1100c before recording (see page 23).

The USB hard drive can also be connected to a MAC or PC for transferring, archiving and viewing the recorded programming. Transfer programs onto your laptop for enjoying programs on the road! Many computer viewing programs are available for free. Examples: Media Player Classic - Homecinema (www.mpchc.sourceforge.net) for the PC or iSkySoft (http://www.iskysoft.com) for MAC.

It is simple to burn digital quality DVD copies of a TV program in just minutes with iSkySoft for MAC and VideoReDo TVSuite (www.videoredo.com) for PC.

This software also will rip files so you can enjoy TV and Radio programs on your iPod or MP3 player. VideoReDo will transfer home movies, photos, MP3’s onto the USB drive for display on your TV or audio system through the DVR1100c.

Navigation

Buttons

Recording -

DVR1100c

Connect a compatible FAT32 formatted USB 2.0 drive up to 500GB capacity to enable recording functions. For maximum compatibility, the USB drive must be formatted with the receiver when connecting for the first time. Do not use a computer to delete recordings from the drive. Always use the receiver to delete recorded files.

The USB drive may not work if it features power saving sleep functions or automatic data back-up. A current list of verified drives is available at www.

geosatpro.com.

Program recording can be started quickly with the INSTANT RECORD button,

PAUSE button or set up as a timed event. If the program title is listed with the

EPG (Electronic Program Guide) button, highlight the desired program and press the RECORD button. The program record date, start and duration times will be automatically set.

B. Gohl

GEOSATpro

Timer -

DVR1100c

If no event information is available in the EPG, press the TIMER button and manually set an event timer:

• Event Number: 10 timers available

• Enable a Timer: YES / NO

• Type: ONCE, DAILY, WEEKLY

• Channel: Choose the channel from the Channel List

• Month of the event

• Date of the event

• Start Time: Set in 24 Hour Mode. I.E. 5pm = 12+5=17:00

• Duration: Set the length of recording. A setting of 00:00 will not record, but instead bring the channel on screen for viewing at the preset time.

Maximum record time for manual recording setting is limited only by the available free space on the drive.

You can often view or listen to other channels while available channels that share the same transponder.

Time Machine -

DVR1100c

Time Machine is a function that can be enabled by the customer to allow up to

4GB (4 hours) of programming to be automatically and continuously recorded and available for review as long as the receiver is not in the OFF or STANDBY mode. The selected or viewed satellite channel will be automatically recorded onto the attached USB drive. If the channel is changed, the recording will start again and the previous recorded programming will be erased. Time Machine recordings cannot be saved.

www.geosatpro.com Toll Free 888-483-4673

To create a Time Machine partition on the connected USB drive:

1. Press MENU

2. Select ACCESSORY

3. Highlight TIME MACHINE

4. Press OK

5. Set File size: 512M (30 min.), 1G (1 hour), 2G (2 hours,

3G (3 hours), 4G (4 hours)

6. Highlight CREATE Press OK

Program Playback -

DVR1100c

Programming can be played back (Time Shift) even while the program is still recording. Most playback controls are available during both recording and playback modes.

To Playback a prerecorded program, press the PLAY button to display a list of available recordings. Highlight and press OK.

Press the PAUSE button any time that you wish to step away from the program.

Press PLAY to resume playback.

Miss a telephone number, address or announcement? Press the 30 SECOND or the 5 SECOND REWIND button to skip back.

Press SCAN REWIND or SCAN FORWARD to rapidly scan recordings at 2x,

4x, 8x, 16x or 32x speeds.

While the Program Banner is displayed at the bottom of the screen (press INFO button), Press the LEFT arrow button to Rapidly skip backward or move to the start of the recording. Press the RIGHT arrow button to rapidly skip forward in the recording.

Delete Recordings -

DVR1100c

• Press the PLAY button to display the Recorded Program List

• Highlight the program to be deleted

• Press the BLUE button to delete

B. Gohl

GEOSATpro

Installation Guides

29 pages before beginning the installation.

Save all original boxes, manuals, accessories and packaging equipment for refund or exchange.

Before unpacking or assembly of any item, review the

Sales Invoice.

Glorystar equipment or installation

This guide is intended for an individual experienced in performing the various tasks described, including:

• Determining an antenna location with a view of the satellites positions.

• Climbing a ladder and working on your roof.

• Observing safe working practices around heights and electrical hazards.

• Determining if water pipes, gas lines or wires are hidden before drilling.

• Using a power drill to drill holes into your house.

• Routing cable through walls, crawl spaces or attics.

• Safely lifting and securing the 25 lb. antenna assembly.

• Grounding the system as recommended in the National Electric Code.

If you don’t feel completely comfortable with these tasks, you may consider contracting the installation with a local satellite technician.

Web site http://www.FTAinstall.com provides a free referral service for local installers. Please visit today!

www.geosatpro.com Toll Free 888-483-4673

Glorystar System Parts List

Reflector (1)

LNBF ARM (1) Post (1)

Tripod Support Leg (2)

LNBF Arm Supports (2)

Installation Kit (1)

Satellite Receiver and Remote (1)

Dish Accessory Kit (1)

LNBF (2)

* 1 in Adventist Kit

22KHz Switch (1)

* not in Adventist Kit

3’ Coax Jumper (2)

* not in Adventist Kit

Twin LNBF Clamp (1)

* not in Adventist Kit

Tools Required

Phillips Screwdriver

1/4” Socket

Drill and Bits

B. Gohl

Measuring Tape Hammer

GEOSATpro

Site Survey

If you feel comfortable with drilling holes in the walls and/or roof of your home, climbing ladders, attaching wires to the ground according to NEC and local codes and following step-by-step instructions, you might consider installing your own system.

The satellite is located over 23,000 miles away and the installation does require precise tuning and a great deal of patience to correctly install. Have you recently installed a light switch, ceiling fan, basketball hoop and programmed a VCR? If not, this project might not be a good time to hone your mechanical and electrical skills!

If you wish to schedule your own installation, visit

http://www.ftainstall.com

. This site will introduce you to local professionals and also laypersons who install

Christian satellite systems as a ministry outreach.

Before assembling any equipment it is important to verify that the installation location has a suitable area to safely and securely mount the satellite dish and have a clear line of site to receive the satellite signal. The satellite dish must be pointed directly at the satellite, with NO obstructions between the two. This means NO trees and

NO buildings. Satellite signals will not pass through leaves, limbs, so consider future tree growth, house remodeling or additions and new construction in your area. Do not attempt to install the dish indoors!

www.geosatpro.com Toll Free 888-483-4673

Where Is The Satellite?

Generally the dish will be pointed towards the South, Southeast or Southwest. The satellite is located south of Texas and Mexico directly over the equator. That means if you live in Miami, you must have a clear line of sight to the Southwest; if you live in San

Francisco, you must have a clear line to the Southeast.

Compass Azimuth Reading:

_______________

How High Up in the Sky is the Satellite?

Depending on where you live, the satellite will be at an elevation angle between 30 and 60 degrees. Southern US point more toward

60 degrees; northern US point more toward 30 degrees. Northern

Canada and Hawaiian elevations can be as low as 10 degrees, but in Central American dishes are aimed almost straight up!

Dish Elevation Angle: ___________

B. Gohl

GEOSATpro

Compass

Elevation Angle Finder

Using the aiming coordinates included with this system or found at http://www.GeoSatFinder.com along with a compass and the

Site Check Angle Finder located on the last page of this manual, locate a suitable dish mounting position. While facing south, hold the compass level in the palm of your hand. With the red needle pointed exactly at North, reference the compass reading. Are there any obvious obstructions? If the line of sight appears clear, continue to the check the elevation angle. Sight along the top edge of the elevation angle finder with the weighted string registering the correct elevation angle. Is the line of sight clear with no branches, limbs or tall buildings? The Elevation Angle Finder is only used for the site check and cannot be used to measure the elevation angle of the dish.

The elevation scale on the back of the dish is used for setting the correct elevation angle.

Reception of One or Two Satellites

If you are installing a Glorystar two satellite system, the satellite dish receives channels from two satellites located 4 degrees apart, SES1-

KU (formerly AMC4) at 101W and Galaxy19-KU at 97W. These satellites are in the same location as the DirecTV main satellite at

101W. If DirecTV can be installed, you will receive Glorystar.

www.geosatpro.com Toll Free 888-483-4673

Dish Mounting Options

We recommend ground mounting the dish on a 1 5/8” heavy wall galvanized post set in cement. Attach a bolt or muffler clamp to the bottom of the post to prevent the post from twisting in the hardened cement. These items are readily available at any hardware store.

Filling the post with a wet cement mixture will provide greater rigidity. The post must be perfectly plumb, level on all sides.

Posts standing higher than 7 feet should be stabilized to prevent movement during high winds. The post should be installed in

Ground Post Mount advance of the install as the cement can take

24 - 48 hours to set. Do not install the dish on a wooden 4” x 4” post or on a tree. The grain of the wood will twist during dry and rainy seasons causing the dish to swing off of the satellite causing reduced or loss of signal. Take proper precautions to protect the dish from being bumped during yard care or damaged by children at play.

Wall Mount

Roof Mount

The Glorystar system includes a heavy duty universal wall / roof post mount. This mount can be attached at almost any angle and provides a stable secure mount even in high wind regions if properly attached. If this universal post mount is used, the included tripod legs MUST be installed. The universal post will fail under moderate wind load if the tripod legs have not been installed to support the larger wind load area of a 36” dish. The dish and mount are designed to remain operational in winds up to 80+ mph and survive wind gusts over 110+ mph.

B. Gohl

GEOSATpro

Dish Assembly

Once a suitable dish mounting location has been chosen it is time to set up the dish. Use the large cardboard shipping box as a working surface to prevent damage to the dish components during assembly. We recommend assembling the dish first and then installing on the post mount.

It is important to check the reflector for warping before assembly of the satellite dish.

Dish Reflector Accuracy

Before assembling the dish it is Extremely Important to verify that the reflector was not warped or bent during shipping. Failure to check for dish warping or damage could lead to many frustrating hours of trying to locate the satellite. This simple test may be the most important step in a successful installation!

Bad - Warped Reflector

Good - Reflector

Find a perfectly flat surface such as a garage cement floor and lay the reflector face down. Are the edges of the reflector laying perfectly flat? If any area of the edge is raised by even an 1/8th of an inch reception of the satellite signal could be affected! If you cannot find a perfectly flat surface to check the dish edges, try the string test.

Tape a string horizontally from edge to edge across the center of the dish

Tape a string vertically from top to bottom on the edges of the dish.

If the strings do not touch in the center, the dish is warped and will need to be corrected before assembly or aiming.

www.geosatpro.com Toll Free 888-483-4673

If the reflector is warped, pick up the dish by the edges like a steering wheel and quickly thrust the reflector away from your body while holding the edges of the dish like passing a basketball. This action will cause the reflector to flex and it will spring back into the factory pressed shape. Lay the reflector face down and observe if the edges are now laying perfectly flat. If not, repeat the flexing process until the reflector edges are uniformly flat.

Important Note:

An assembled dish will not be accepted for refund.

GEOSATpro 90cm Dish Hardware

Item Quantity Description

1 6 Carriage Bolt

2 2

3 2

4 13

5 1

Phillips Screw

Hex Nut

Carriage Bolt

6 1

7 2

8 2

9 2

10 2

11 2

12 1

A 4

B 1

C 1

D 1

Structural Bolt

Elevator Bolt

Washer

Carriage Bolt

Phillips Bolt

Hex Nut

Phillips Bolt

Hex Flange Bolt

Hex Nut

Hex Tap Bolt

Fastener Insert

Size

1/4” x 1/2”

M4 - 16m

1/4”

1/4” x 1 1/4”

1/4” x 2 1/2”

1/4” x 1 1/4”

1/4”

1/4” x 3/4”

1/4” x 1/2”

1/4”

1/4” x 1 1/4”

1/4” x 1/2”

1/4”

1/4” x 3 1/2”

Please contact your reseller if any of these parts are missing or damaged. Most hardware items can be found at a local hardware supply store.

B. Gohl

GEOSATpro

Attach the LNBF Arm to the Elevation Bracket.

Assemble the Elevation Bracket and Post

Clamp. The Post Clamp has two holes drilled. One hole is stamped with an A and the other with a B.

Assemble the Elevation Bracket to the

Post Clamp inserting Structural Bolt A

(part #6) through the hole stamped A if the Dish Elevation Angle is between 10 -

60 degrees. Assemble using hole stamped

B if the elevation angle is to be between

50 – 90 degrees. Most installations in the US and Canada will use Elevation

Scale A type assembly. Installations in

Mexico will usually use Elevation Scale

B assembly.

The dish has been correctly assembled for Measuring the Dish Elevation

Angle using Scale A (10 - 60 degrees) if a letter B is visible stamped on the

Post Clamp on the left side of the Post

Clamp.

After verifying the Reflector is not warped, mount the Reflector to the Elevation

Bracket and install the two LNBF Arm

Side Supports. The Side Arm Supports will perfectly center and support the LNBFs for optimal reception.

www.geosatpro.com Toll Free 888-483-4673

Universal Post Mount Assembly

Mount the Universal Post Mount Foot Plate to a wall stud or roof rafter using two 5/16th x 3” lag bolts. Adding 5/16th x 2” lag bolts on the outer edges will increase stability. To prevent water leakage, use the included silicone sealant or other waterproofing product on all wall or roof penetrations.

The Universal Post Mount can be assembled for roof or wall type installations. The post has slots for attaching to the Foot Plate on both ends of the tube. This allows the dish to be mounted with either a higher reach above a roof (as pictured) or outward reach away from a wall when using the slots on the opposite end of the post.

Level and Secure Post

Insert the Bubble Level into the top of the post. Be sure that it is seated level with the top edge of the post.

The unique slots in the post tube allows the post to be leveled or made plumb in any installation position. Center the bubble in the level then tighten the 4 flange bolts to secure the post. It is very important to make sure that the post is perfectly plumb (level on all sides).

B. Gohl

GEOSATpro

Example: Positive +20°

If the post is not exactly plumb, the elevation scale will not be accurate and it will be very difficult to locate the satellites and properly tune the dish for reliable reception.

Not Level Level

The Most Critical step to providing a stable mounting platform for the dish is the installation of the Tripod Support Legs. If the lag bolts cannot be secured directly into a stud or rafter, the legs should be secured into plywood sheeting with either a backing a toggle bolt or to a 2 x 4” that is lag bolted between the rafters or studs.

The legs are required to support the wind load on the universal post mount. Failure to install the tripod support legs will result in collapse of the post during moderate winds. The post is not designed to solely support the dish. If you hire a local installer, please be sure that the legs are installed.

Glorystar Dual LNBF Bracket Assembly

Install the 4 Degree Rotating

LNBF Clamp. The Skew Angle number scale (LNBF Rotation) must be visible while standing in front of the dish looking into the reflector. Attach the LNBF clamp to the LNBF arm. LNBF #1 is on the right side of the Clamp, LNBF

#2 is on the left.

Stamped printing on the clamp bracket faces out towards the sky, not inside facing the reflector.

Skew Angle:

___________

(LNBF Rotation) www.geosatpro.com Toll Free 888-483-4673

Rotate the Twin LNBF clamp to the

Skew Angle (LNBF Rotation) specified in the aiming coordinates. Standing in front of the dish looking towards the reflector, a Positive (+) Skew Rotation is set counter clockwise meaning that the left LNBF is rotated lower than the right LNBF. Negative Skew (-) is a clockwise rotation and the right

LNBF is rotated to be lower than the left LNBF.

Example: Negative -40 is set while standing in front of the dish looking towards the reflector face.

Each mark on the clamp measures 5°. If the aiming coordinates specify a skew angle of +25, set the pointer to Positive 25°

(counter clockwise). Tighten the locking nut securely to prevent any movement.

This setting should be adjusted, locked and not require any further adjustment.

If the Mast or mounting post is not

PERFECTLY plumb, the skew angle will not be correct and the dish will be difficult to aim!

Install two GEOSATpro Mini Bullet LNBFs into the Twin LNBF

Clamp, align the centering line on the top of each LNBF with the centering pointer on the clamp. Slide the LNBF forward towards the

B. Gohl

GEOSATpro

41 reflector so the white front face of the LNBF cap is slid 20mm (3/4”) forward of the clamp towards the reflector. Securely tighten both clamp screws (2).

LNBF #1 is for SES1 101W (formerly AMC4) reception and LNBF #2 is for Galaxy19 97W. The

LNBF Skew Scale is visible standing in front of the dish looking towards the reflector.

LNBF

Single Satellite Bracket

Assemble the single LNBF Clamp and attach to the LNBF arm.

LNBF

Standing in front of the dish looking towards the reflector, rotate the LNBF counter clockwise

(left) for a positive (+) LNBF Rotation setting and Clockwise (right) for a negative (-) LNBF

Rotation setting.

Set the LNBF Rotation (Skew Angle) to the setting specified in the aiming instructions provided with your system. The LNBF rotates in the circular clamp until the centering line on the top of the LNBF aligns with the LNBF Rotation angle.

www.geosatpro.com Toll Free 888-483-4673

Dish Aiming

Level and Secure Post

Place the assembled dish onto the post. Set the Dish Elevation to the angle provided on the cover of this manual.

The pointer for the elevation indicator is a white line that is visible through the elevation scale and is located near the edge of the elevation fastening nut.

Semi-tighten the elevation fastening nuts to hold the dish in position.

Do not tighten the fasteners for final setting at this time. Additional adjustment will be needed to locate and peak the satellite signal.

Do not grip the edges of the reflector to adjust the dish. Always hold the dish by the elevation bracket during elevation or azimuth

(side-to-side) adjustments. Applying pressure to the reflector will affect the accuracy of the satellite signal reflection from the dish into the LNBF.

B. Gohl

When setting the dish elevation angle it is important to note that the face of the dish will be aimed lower than the actual elevation angle to the satellite. The scale on the elevation bracket is calibrated for accurate aiming if the post has been installed perfectly plumb (leveled on all sides). The dish elevation angle cannot be set using an angle finder on the LNBF arm or on the face of the dish.

GEOSATpro

Compass Reading: Azimuth

In North America, satellites are always located South of your location.

To correctly aim the dish you must first accurately determine the exact compass reading angle (azimuth). Metals, electricity and other magnetic disturbances can cause the compass to point incorrectly.

Compass readings should be made at least 10 feet in front of or behind the metal satellite dish and away from any large metal object such as metal buildings, air conditioners, vehicles, utility and power lines or electrical panels. Check compass reading several times to reduce install time and the need to hunt the entire southern sky for the satellite signal.

California

Texas

New York

Example: Texas Magnetic Compass Reading 180 degrees.

Identify a reference point on the horizon like a tree, utility pole or other landmark that lines up with the compass reading. Installers often find it easier to align the dish if they can reference an object that has been identified with the compass reading. If you cannot locate a visual reference, stretch a 10 - 20 foot rope out in front of the dish in the direction of the compass reading.

Move directly behind the dish and align the dish so that the LNBF arm is aimed directly at the reference landmark or in line with the rope. Semi-tighten the post clamp nuts, but allow the dish to be just loose enough to be moved left or right by gripping the elevation bracket with applying light pressure. www.geosatpro.com Toll Free 888-483-4673

Connect Receiver to a TV

The easiest way to aim the satellite dish is to temporarily place the satellite receiver connected to a small television at the dish antenna mounting location.

CAUTION: DO NOT ATTEMPT TO OPERATE

ELECTRONIC DEVICES IN AN UNSAFE

LOCATION OR IN VIOLATION OF SAFEGUARDS

PROVIDED IN THIS MANUAL OR ANY OTHER

EQUIPMENT MANUAL PROVIDED WITH THIS

GLORYSTAR SATELLITE SYSTEM.

Remove the satellite receiver and remote control from the packaging.

Inspect the unit before operation. If any equipment is damaged or if you have any questions, please immediately contact Glorystar or your reseller.

Install the two included AAA batteries into the remote control battery compartment..

Connect the satellite receiver to the TV.

The most basic connection is to locate the included 6’ coax jumper with the plastic moulded ends and connect from the TV

/VCR port on the satellite receiver to the

Antenna connection on the TV. Plug the television power plug into a surge protected power strip. Turn the TV power on and set the TV to channel 3. The TV is now set-up to view the satellite receiver.

Plug the satellite receiver’s AC power plug into the same power strip. Power ON the Master Power Switch on back of the receiver.

The receiver will power on and the front panel will display “boot”.

The TV will display the Language Selection Screen.

B. Gohl

GEOSATpro

Receiver Connection Examples

Audio / Video RCA S-Video / Audio RCA

Component Video / Audio RCA Cable, DirecTV, Dish or Antenna

VCR or DVD Recorder

Please consult the owners manual provided with TV, VCR or other device that will be connected to the Glorystar satellite receiver.

The manual will include important connection and operational information. Questions regarding the connection to any other equipment should be directed to the manufacturer of that device.

www.geosatpro.com Toll Free 888-483-4673

Activating the Glorystar Receiver

Remote Control

Navigation Buttons

1. Highlight the language for the receiver menus. If required, press the remote control navigation UP arrow to select an alternative language. Press OK to accept the language and go to next screen.

2. For a two LNBF dual satellite

Glorystar System, select System

Type G

LORYSTAR. Press OK to proceed to next screen.

3. Select your Time Zone by pressing the RIGHT or LEFT arrow.

4. Press the Down arrow to select Daylight Savings. Press the RIGHT arrow to select ON if time is in Daylight Savings. The time will now be automatically synchronized via the satellite. Press the Down arrow to highlight

NEXT. Press OK to accept and go to next screen.

5. Connect the coaxial cable directly from LNBF #1 on the dish antenna to the SAT IN port on the back of the satellite receiver. DO

NOT install the 22KHz - 2x1 switch at this time.

B. Gohl

GEOSATpro

6. Press OK to display the Signal Strength and

Signal Quality meter with Signal Quality Tone

Beeper on the connected television.

DO NOT connect the 22 KHz

switch at this time!

The receiver will automatically tune to channel 500, CGN TV

(Korean). A loud beeping sound will be emitted from the TV speakers. The beeping pitch will increase when the satellite signal is detected. Pressing the Blue Button on the remote toggles the beeping sound ON/OFF.

This screen shot shows a receiver that is not properly connected. A

Signal Level (S) of 0-10% indicates that there is no connection between the receiver and the LNBF. Check to make sure that a coax cable is attached from the SAT IN port on the rear of the satellite receiver to the LNBF #1 on the satellite dish.

www.geosatpro.com

A Signal Level (S) reading of 50% or better indicates that the receiver is connected to a working LNBF.

Low Signal Quality (Q) readings at or below 30% indicate that the dish is not properly aimed or the

LNBF is not properly rotated to receive the satellite signal.

Toll Free 888-483-4673

Locate and Peak Satellite Signal

While observing the Signal Quality (Q) reading, slowly move the dish towards the right. Reference the distant landmark or the string on the ground that you identified in your site check that corresponds with the Azimuth (compass) reading. Usually the satellite will be found within a few degrees either side of the compass reading.

If the dish is moved beyond 15 degrees from the site’s compass reading and no Signal Quality (Q) is detected, sweep 15 degrees in the opposite direction. When the correct satellite is found the beeping sound changes to a higher tone, the Signal Quality (Q) bar turns

Green and the Spectrum Graph displays changes in Signal Quality.

The Signal Quality (Q) readings will increase as the correct satellite is detected and fine tuned. If the dish is aimed at the correct satellite, the Quality (Q) reading will display a Green Signal Quality (Q) reading and display a picture.

The Signal Level (S) is not important in detecting the satellite.

Signal Level readings indicate a connection to a functioning

LNBF, not the detection of the correct satellite.

If no Signal Quality (Q) reading is detected, increase or decrease the elevation by one degree and repeat the slow sweep. The elevation may need to be adjusted +/- 5 degrees depending on the post being plumb. Move the dish very slowly to allow the receiver to process the signal information and update the meter. A movement of just 1/16th of a inch can result in a perfect or no signal. This process may need to be repeated many times to aim and peak the quality of the signal.

When the dish is correctly aimed the programming will display and the Signal Quality (Q) reading will display a 50% or better level on

CGN channel. A stable signal on the Spectrum Graph with minimal ripple indicates that the signal is optimized.

B. Gohl

GEOSATpro

Once the correct satellite is located, make small adjustments in elevation and azimuth until maximum signal is indicated on the quality bar. Signal Quality (Q) readings should be 50% or better on the CGN TV channel to insure optimum picture and sound on all channels. The higher the quality reading, the better the reception. If the Signal Quality reading is low, the picture will break up into little squares and the sound will become garbled, out of sync, choppy or will disappear completely!

Congratulations! The first satellite is now tuned! There are a few more steps to optimize your installation for reception of all Christian channels on the 2nd satellite, Galaxy 19 97W.

Disconnect the coax cable from

LNBF #1 and connect to LNBF #2.

Press the CH/DOWN arrow button on the remote control to place the receiver on TBN, Channel 101. This is a strong channel on the

2nd satellite, Galaxy 19 on LNBF #2. www.geosatpro.com

Verify the Signal Quality reading is at least 50% and displaying a picture. If the Signal Quality (Q) is less than 50%, make very small adjustments to fine tune the dish elevation and azimuth (side to side).

Toll Free 888-483-4673

Note: Do not re-adjust the skew rotation of the twin LNBF clamp or adjust the LNBFs rotation or placement while locating the satellites. This will make the installation process very difficult!

Switch Installation

It is always a good idea to turn the Master Power

Switch, located on the rear of the receiver OFF to prevent damage to the switch while connecting cables.

Connect the coax cable from the receiver to the

Switch port labeled RECEIVER (RX). Connect a 3 foot coax cable from LNBF #1 to the Switch input port #1. Connect the second 3 foot coax cable from LNBF #2 to Switch input #2.

Mount the Switch on the back of the dish and secure the coax cables and Switch to the LNBF arm with nylon ties.

You may now safely Power On the Master Power

Switch located on the rear of the receiver.

#2

#1

Completing the Installation

Place the receiver back on CGN TV

(Korean) Channel 500. Press the

ORANGE Signal button to display the Signal Meter. Verify that the

Signal Quality is still at least 50% on

LNBF #1 and displaying a picture.

Place the receiver on Cornerstone

TV, Channel 113.Verify the Signal

Quality (Q) reading is at least 50% on LNBF #2 and displaying a picture.

The dish is accurately aligned for reception of both satellites when the Signal Quality is at least 50% on all channels on both satellites.

B. Gohl

GEOSATpro

Congratulations! The satellite system is properly installed and it is time to update the channel list. If any of the channels display a

Signal Quality (Q) reading that is below 50%, additional fine tuning adjustments should be made to the dish elevation and azimuth aiming. If these adjustments do not increase the signal quality, slight adjustments to the LNBFs rotation or placement may be necessary.

LNBF Adjustment - (optional)

LNBF Rotation Fine Tuning

LNBF #1 or #2 can be slightly rotated within the twin LNBF clamp +/- 5° to optimize the satellite quality readings.

Slightly loosen the two Phillips head screws that secure the twin LNBF clamp. Place the receiver on the weakest SES1 101W channel and slowly rotate LNBF #1 left or right. If no improvement in quality, re-center the LNBF. Place the receiver on the weakest Galaxy19 97W channel and slowly rotate

LNBF #2 left or right. If no improvement in Signal Quality (Q), recenter the LNBF.

LNBF Position Adjustment

LNBF #1 or #2 can be slightly positioned in the twin LNBF clamp towards or away from the reflector to optimize the satellite quality readings.

Place the receiver on the weakest SES1 101W channel and slowly slide LNBF #1 in toward the reflector or out away from the reflector.

If no improvement in Signal Quality (Q), return the LNBF to the

3/4” forward position. Place the receiver on the weakest Galaxy19

97W channel and slowly slide LNBF #2 in or out. If there is no improvement, return the LNBF to the 20mm (3/4”) offset. Tighten the two Phillips head screws to secure the dual LNBF clamp.

www.geosatpro.com Toll Free 888-483-4673

Updating the Glorystar Channel List

The Glorystar satellite receiver has been shipped preprogrammed with a list of the channels available at time of manufacturing.

The receiver will be automatically updated with the most current channel list each week with a channel list update sent via the satellite. Glorystar recommends that the channel list be manually updated using the UPDATE NOW feature at the completion on the installation.

- Press Menu

- Press Left Arrow to Accessory Menu

- Highlight OTA. Press OK.

- Select Automatic Update

- Press OK to display OTA Menu

- Verify OTA Update feature is ON

- Highlight UPDATE NOW

- Press OK

- Confirm Signal: OK (if not, adjust the dish)

- Press OK to update

- The update will take several minutes.The receiver will restart on Glorystar Channel

#1 and the time will automatically set in approx. 15 seconds.

Important Notice: Do not turn off Automatic Update!

If the Automatic Update feature is turned OFF, the channel list will not be updated, new features cannot be added to the receiver and the Glorystar informational channels will not be updated with new programming.

B. Gohl

GEOSATpro

Two Room Install Diagram - (optional)

Multiple Room Install Diagram

www.geosatpro.com Toll Free 888-483-4673

Installation Guide

Advanced / Hobbyist

1. Highlight the language for the receiver menus. Press OK to accept the language and go to next screen.

2. Highlight the System Type

Advanced (All Satellites). Press

OK to accept and go to next screen.

3. Select your Time Zone by pressing the RIGHT or LEFT arrow.

4. Press the Down arrow to select Daylight Savings. Press the RIGHT arrow to select ON if time is in Daylight Savings. The time will now be synchronized via the selected satellite channel.

5. Press the Down arrow to highlight NEXT. Press OK to accept and go to next screen.

6. Connect the coaxial cable from the LNBF on the dish antenna to the SAT IN port on receiver rear panel. Press OK to go to next screen.

B. Gohl

GEOSATpro

7. Press the RIGHT arrow to select

Installation Menu. Press the Down arrow to select Channel Search. Press OK to accept and go to next screen.

The receiver must be configured for the satellite that you wish to receive and the satellite equipment that is connected.

Before programming the receiver you will need to know what satellite carries the channels that you wish to receive. If you do not know the name of the satellite, visit www.satelliteguys.us/thelist/ for a list of satellites and channels. The majority of free channels in North America are found on satellite Galaxy 19 97W (G19-KU).

For this installation example, we will use satellite G-19 and select an active transponder on that satellite of 12177MHz.

8. Enter Password (default 0, 0, 0, 0)

9. Satellite - Press OK to display list of satellites. Select the proper satellite (G19-

KU). Press OK.

10. TP Frequency - Press OK to list preprogrammed transponders. Select an active frequency (12177). Press OK.

Determine the type of LNBF that will be connected. The LNB type or

LO frequency is normally printed on the LNBF label or packaging.

A Standard type LNBF LO frequency is 10750 and an Universal 1 type LNBF LO frequency is 9750/10600). For this example we will use Standard type LO 10750.

11. LNB - Press OK list LNB LO type or frequency. Select LO type or frequency (10750). Press OK www.geosatpro.com Toll Free 888-483-4673

12. Adjust LNBF Rotation - Set the Skew

Angle to the angle provided with the aiming instructions provided with your system or visit www.GeoSatFinder.com to calculate the aiming coordinates for your area. Rotate the LNBF in the circular clamp until the centering line on the

LNBF aligns with the LNBF Rotation angle.

Example: Positive +20°

Standing in front of the dish looking towards the reflector, rotate the LNBF counter clockwise (left) for a positive (+)

LNBF Rotation setting and Clockwise

(right) for a negative (-) LNBF Rotation setting.

13. Adjust Dish - Aim the dish using the elevation and azimuth coordinates provided with your system or at www.GeoSatFinder.

com. While viewing the Signal Quality (Q) meter reading, Adjust the dish until the highest (Q) reading is displayed. Peak the (Q) reading with slight LNBF placement and rotation adjustments.

14. Search - When the Signal

Quality (Q) meter is displaying a reading above 50%, Press OK to scan for all available Free channels from the preprogrammed transponders. If prompted, press

OK to confirm changes.

Not Aimed Correctly Aimed

15. Channel Search Completed - Press

OK to save found channels. Press Exit two times to exit the menus and view scanned

TV and Radio channels.

B. Gohl

GEOSATpro

Using Satellite Meters

Inexpensive satellite meters can speed up the installation process, but they only display the signal strength of a satellite.

It is important to understand that signal strength satellite meters do not indicate if the dish is aimed at the correct satellite and they will not be useful for fine tuning the dish aiming or LNBF skew (rotation or tilt) for maximum Signal Quality. Signal strength meters must be used along with the satellite receiver to determine if the dish is aimed at the correct satellite.

A digital identification meter such as a SatBuddy or BirDog will simplify the installation process. Please consult with the owners manual for correct operation. We recommend SatBuddy meters.

Install Procedure with a Signal Identification Meter

• Connect LNBF # 1 (right side) to the meter and use data for standard LNB type LO 10750, KU, SES1 (AMC4), Horizontal and

Vertical transponders. Peak for maximum Signal Quality (Q) for

SES1 (AMC4) 101W.

• Connect LNBF #2 (left side) and use a data set for standard

LNB type LO 10750, KU, Galaxy19 101W, Horizontal and Vertical transponders. Peak for maximum Signal Quality (Q) for G 19.

• Verify and balance the aiming for optimum SES1 and Galaxy

19 Signal Quality (Q) and reception.

Note: Birdog meters may have difficulty detecting weaker FSS type signals and must have the BER setting changed. Enter the main setup menu and change the BER setting to LOG (logarithmic).

Installer Tip

If you are having trouble locating the satellites, remove both LNBFs from the clamp and install a DirecTV LNBF into the LNBF #1 (right side) position. Locate the DirecTV 101w satellite with your meter or a DirecTV receiver. Replace the Glorystar LNBFs into the clamp.

The Dish is now roughly aimed and will only require fine tuning for optimal reception of the linear satellites.

www.geosatpro.com Toll Free 888-483-4673

Completing the Install and Grounding

Carefully route the coax cable from the dish to the ground block then to the satellite receiver. Secure all cables using appropriate cable clips and nylon zip ties. Avoid using wire staples as they can dimple or penetrate the cable and can cause loss of signal! Form drip loops and cable loops as needed to prevent water from running down the cables and entering cable connection fittings or into wall penetrations. Remember to seal all exterior wall and/or roof holes with a quality sealant or silicone caulking.

Install the grounding block and wire while observing all NEC,

National Electrical Code and local codes. Connect the ground wire to the structure ground. If you are unsure of how to properly ground your satellite system, please consult with a local professional.

Copies of the NEC are available at your local library or online.

Important Notice:

GEOSATpro recommends that you DO NOT use existing coaxial cabling that has been pre-wired or previously used in your home. Often these cables are low quality RG-59 and not rated for satellite applications or have splitters and other devices that are not compatible. Always connect the RG-6 type coax cable directly from the satellite dish LNBF through the grounding block and attach to the LNBF IN Digital connection on the rear of the

Satellite Receiver.

Cable splitters or any other devices in the coax line may cause the satellite receiver to shut down or malfunction. Do not use any device in the coax line unless approved for satellite installation. Multiple receiver installations must use a multiple output LNBF to avoid programming conflicts between the receivers.

B. Gohl

GEOSATpro

FAQ – Frequently Asked Questions

How are new Glorystar channels added to the channel list? The receiver will automatically download any new Glorystar channels during the weekly receiver satellite update. If you do not want the channel list to be automatically updated, see OTA Updating section on page 24 for instructions on disabling the OTA updating feature.

Satellite receiver displays “Warning - Do NOT power off Software Download”

for more than 1/2 hour. The satellite signal may have been interrupted during the automatic updating process. Reset Master Power switch on rear of the receiver.

Place receiver on channel 1 and press the Signal button on the remote. If the SQ is below 40% the receiver will not update and may require dish adjustment.

Remote doesn’t work but receiver front panel buttons may turn on/off and

change channels. Check batteries. Press any remote key and observe if the remote control POWER button. If the POWER button lights, the batteries should be strong enough to operate. Is the remote aimed at the receiver? The remote will not work through walls, cabinet doors, etc. Reset Master Power switch on rear of the receiver.

No lights on receiver. Check power plug make sure that it is plugged into a working electrical outlet. Always plug the receiver into a surge protector power strip to help prevent damage by power line surges and lightning strikes. Reset

Master Power switch.

Receiver displays 50% or better Signal Level (S), but no Signal Quality (Q)

on all channels. The receiver is connected to a LNBF, but the dish might be pointed at the wrong satellite or there may be an obstruction in the line of sight between the dish and satellite. Mounting mast may be loose or moved.

Meters display 0% signal level and no quality. Coax not connected from LNBF on dish to SAT INPUT on receiver. Dish not properly aimed. Bad coax, connectors or LNBF failure.

Channels are coming in from only one satellite. Dish may not be properly aimed. The coax cable, connectors, switch or LNBF could be damaged or failed.

Turn off Master power Switch on rear of receiver. Remove switch and directly attach the coax from the receiver to LNBF #1 (right side). Tune the receiver on

CGN Channel 500 and press SIGNAL button. If good Signal Quality, the LNBF and coax are good. Connect the coax from the receiver to LNBF #2 (left side).

Tune to TBN channel 101. If Signal Quality is good, this LNBF is good. Turn off

Master power Switch on rear of receiver. Reinstall the switch.

Picture breaks up into big blocks and the audio is garbled. The antenna might be slightly out of alignment.. Satellite view partially obstructed. Damaged coax or connections.

Satellite receiver has a channel number on front panel, but TV displays

snow. Tune TV to channel 3/4 if using the TV/VCR coax cable to attach to the

TV or select the AV, COMPONENT, S-VHS input if using the these types of connections.

No audio on any satellite channels. Set satellite remote control audio up to 75% and use the TV volume control to adjust volume. www.geosatpro.com Toll Free 888-483-4673

Local or cable TV channels are fuzzy and channel number is displayed on

front panel. Turn off the satellite receiver or press the ANT/SAT button when watching local or cable channels. Loop through function for antenna or cable is only available using the TV/VCR coax connection to a TV. Antenna or cable signal are not passed through the Video, Component or S-VHS connectors.

Picture breaks up during rain and snow. Heavy rain or clouds may affect the strength of the satellite signal. A properly installed dish will rarely lose signal during extreme weather. Snow or ice build up can interfere with the satellite signal. Mount the dish where snow can be gently brushed off. Dish covers and heaters are available for locations with regular ice and snow accumulations.

Satellite receiver displays “No Signal” only during very hot or cold weather.

An aging or defective LNBF can drift off frequency and cause the loss of reception during the heat of the day or coolness of the night. Replace the LNBF.

Satellite receiver displays “No Signal” or the picture breaks up during high

winds. Strong winds can move the dish out of alignment and cause the signal to be reduced or lost. Make sure the mast support legs have been installed and the mast is secure and not moving. Once the mast is stable, follow the aiming instructions to re aim the dish and tighten all hardware to prevent any movement.

Most channels have strong Signal Quality (Q), but signal quality is poor on

some channels or the receiver displays “No Signal”. Some channels have a weaker signal than most other channels and may display a low signal quality or no signal. Installations often need to be fine tuned to receive this weaker station.

Place the receiver on that weaker channel. Press the SIGNAL button and make slight adjustments to the antenna elevation, azimuth and the LNBF rotation and distance from the reflector to peak the quality.

Are more channels available? Many more free channels are available for viewing on this and other satellites. This receiver is capable of programming these additional TV and Radio services. Do this at your own risk, as Glorystar will only provide the warranty free technical support for the reception of the Glorystar programming. The Automatic channel updating feature (OTA) must be turned off to prevent the weekly OTA automatic updates from erasing the additional channels. The customer will be responsible for manually updating the receiver with any new channels or firmware upgrades.

Disabling OTA Automatic Receiver Updating (optional)

Please note: Disabling the OTA function will prevent the receiver from receiving critical updates, new channel updates and important announcements on the

Glorystar information channels 1 - 5.

• Press MENU on the remote.

• Press VOLUME RIGHT arrow to enter the ACCESSORY Menu.

• Highlight OTA. Press OK to enter the OTA Menu.

• Press VOLUME RIGHT arrow to select OFF.

• Press MENU to exit the menu screens.

B. Gohl

GEOSATpro

Scanning the Satellite for Additional Channels (optional)

1. Press MENU on the remote control.

2. Press VOLUME RIGHT arrow to enter the Installations Menu.

3. Highlight Channel Search and press OK

4. Enter Password 0,0,0,0

5. Highlight Satellite and select AMC4 or Galaxy25

6. Highlight Search Options and change setting to Blind Scan

7. Highlight Search and press OK to begin satellite scan. This process will take approximately 10 - 15 minutes

8. After the Scanning is complete, select YES to save the found channels

9. Press EXIT on the remote to begin viewing channels.

Do not call to activate programming or subscription. All channels are free to air and available with no monthly charge. The receiver assigns channel numbers while scanning; therefore, no uniform channel line-up will be available after a scan is performed.

DVR1100c

Picture is skipping and/or audio jumps during DVR functions. A USB device may not have enough transfer speed to handle the DVR function. Make sure that the USB device is 2.0 type. Try another USB drive with better processing speed.

Thumb drives often cannot process the data and the picture pixilates or freezes.

Message window displays “NTFS: Not supported” when trying to record.

The connected USB device is not formatted to FAT32 type. Use the receiver USB format function to format to FAT32 type

USB drive mounts and dismounts repeatedly. The connected drive has a automatic power saving feature or the sleep function is activated. Follow the directions provided with the drive or provided by the drive manufacturer to disable this function.

USB drive cannot be formatted to a FAT32 type with the receiver. A drive may not be compatible with DVR systems. When choosing a drive, verify that the drive is FAT32 compatible (often displaying MAC computer compatibility).

Avoid drives with auto back-up or power saving sleep features which cannot be disabled. Drives that are not able to be formatted with the receiver often can be formatted to FAT32 type with a MAC computer or with a PC running a disk utility software such as SwissKnife available for free at www.compuapps.com.

Message window displays “Not Enough Room” when trying to record.

The connected USB device is either out of file space or the USB drive is entering a power-saving sleep mode. This model may not be compatible with the DVR.

Please consult with the drive manufacturer.

Glorystar customers may purchase an optional warranty extension and telephone technical support for an annual fee of $19.95.

www.geosatpro.com Toll Free 888-483-4673

Accessories

Your GEOSATpro reseller carries a large selection of satellite accessories and replacement items. Please consider these GEOSATpro accessories for your installation.

Satellite Finder Meter

Installs Faster, Easier

Under Eave Mount

Perfect for Tile or no Hole Roof Mounting

AC Surge Protector

Protect Your Investment

Non-Penetrating Roof Mount

No Holes or Temporary

Dish 1.2 Meter

Reliable Fringe Area Reception

Replacement LNBF

Twin LNBF Clamp

Splitter for 2 TV Viewing

Low Cost 2 Room Viewing

S-Video Cable

Better Quality Picture

RG-6 Coax Cable 3’

Connect VCR or to Splitter

B. Gohl

Extra Satellite Receiver

Replacement or Upgrade

GEOSATpro

Cut Here

63 www.geosatpro.com Toll Free 888-483-4673

Hello! I am an AI chatbot specifically trained to assist you with the GEOSATpro DSR200c Owner's Manual & Installation Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated

Owners Manual

Installation Guide

DSR200c -

Standard Receiver

DVR1100c -

Digital Video Recorder Ready

Attention Glorystar Customers:

Table of Contents

Glorystar Installation Guide

Advanced / Hobbyist Installation

29

54

Important Safeguards

Example of Antenna Grounding

DSR200c / DVR1100c Specifications

DSR200c

Front Panel

DVR1100c

Front Panel

Rear Panel

Remote Control Unit

Remote Key Functions DSR200c / DVR1100c

Remote Key Functions DVR1100c

Basic Remote Operation

Receiver Operation Guide

Channel Information

EPG -

Last Channel

Alternative Audio

Stereo / Mono Audio

Zoom Function

Karaoke

Built-in A/B Switch

Signal Meter

Event Timer

DSR200c

Event Timer -

DVR1100c

Receiver Menu Items

Main Page

I. Channel Manager

I-1. Favorite

I-2. Rename

I-3. Move

I-4. Lock

I-5. Delete

II. Installation

II-1. Channel Search

II-2. Motor Setup

II-1 & 2.b Transponder Edit

II-1 & 2.c Blind Scan

III. Options

III-1. OSD Language

III-2. Control Panel

III-3. Time Adjust

III-4. Security

IV. Utility

DSR200c

DVR1100c

IV-1. System Information

IV-2. USB

IV-3.a Timer / Time Record

DSR200c

IV-3.a Timer / Time Record - cont.

DVR1100c

IV-3.b Time Record -

IV-5. Factory Default

V. Accessory

DSR200c

DVR1100c

V-1. Time Machine -

V-2. OTA

V-3. Smart Card

DVR Operation

-

Recording -

Timer -

Time Machine -

Program Playback -

Delete Recordings -