Swivel Sway Brace Attachment

Swivel Sway Brace Attachment
Seismic Bracing
Component of State of
California OSHPD Approved
Seismic Restraints System
Fig. 910 - Swivel Sway Brace Attachment
Size Range: 1" (25mm) bracing pipe. For brace pipe sizes larger than 1" (25mm),
use Fig. 980. Available with holes for 3⁄8”-16 thru 3⁄4”-10 fastener attachment.
Material: Steel
D
Function: For bracing pipe against sway and seismic disturbances. The
building attachment component of a sway brace system; the Fig. 910 is used
in conjunction with the Fig. 1001, Fig. 1000 or with a Fig. 4A, Fig. 4L, or
Fig. 4LA pipe clamp and joined together with a brace pipe per NFPA 13.
A
B
Features: This product’s design incorporates a concentric attachment
opening which is critical to the performance of structural seismic connections.
NFPA 13 (2010) 9.3.5.8.4 indicates that fastener table load values are based
only on concentric loading. Universal swivel design allows Fig. 910 to be
attached at any surface angle.
Seismic Bracing
E
C
F
Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada
(cUL). Included in our Seismic Restraints Catalog approved by the State of
California Office of Statewide Health Planning and Development (OSHPD,
OPA-0300). For additional load, spacing and placement information relating
to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems
Guidelines.
Mounting Hardware
Is Not Included
Installation Instructions: Fig. 910 is a structural or transitional attachment
component of a longitudinal or lateral sway brace assembly. It is intended to
be combined with the "bracing pipe", and TOLCO "braced pipe" attachment,
Fig. 1000, Fig. 1001, Fig. 4A, Fig. 4L or Fig. 4LA to form a complete bracing
assembly. Follow NFPA 13 and/or OSHPD guidelines.
To Install: Thread the pipe into the Fig. 910 until pipe threads are visible
through inspection site hole. Attachment can pivot for adjustment to proper
brace angle.
Note: Fig. 910 swivel attachment and Fig. 1001, Fig. 1000, Fig. 4A Fig. 4L, or
Fig. 4LA pipe clamps make up a sway brace system of (UL) Listed attachments
and bracing materials which satisfies the requirements of Underwriters
Laboratories and the National Fire Protection Association (NFPA).
Finish: Pre-Galvanized. Contact B-Line for alternative finishes and materials.
Order By: Figure number, pipe size, fastener attachment size, and finish.
Lateral Brace
Part
Number
910-1 X 1/2
910-1 X
5/8
910-1 X
3/4
Brace
Pipe Size
A
B
in.
(mm)
(mm)
in.
(mm)
1”
(25)
2”
(50.8) 11/2” (38.1)
3”
(76.2)
9/16”
2”
(50.8) 11/2”
(76.2)
11/16” (17.5)
25/16” (58.7)
2”
(50.8) 11/2”
(76.2)
13/16” (20.6)
25/16” (58.7)
1”
(25)
(38.1)
(38.1)
3”
3”
(mm)
in.
Max. Design
Load
F
(mm)
(25)
in.
E
in.
1”
in.
Hole Size
D
C
Approx.
Wt./100
(mm)
in.
(mm)
lbs.
(kN)
lbs.
(14.3) 25/16” (58.7)
2”
(50.8)
1600
(8.96)
88 (39.9)
2”
(50.8)
1600
(8.96)
87 (39.4)
2”
(50.8)
1600
(8.96)
86 (39.0)
Eaton’s B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components,
resulting in a listed seismic bracing assembly. B-Line’s warranty for seismic bracing components will be the warranty provided in
B-Line’s standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from
B-Line’s warranty, Eaton’s B-line Business makes no warranty relating to B-Line’s seismic bracing components that are combined
with products not provided by Eaton’s B-Line Business.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
180
(kg)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement