Dimplex | DFG2562 | Owner`s manual | Dimplex DFG2562 Owner`s manual

Owner’s Manual
Model
DFG2562
DFG2562SS
DFG253A
IMPORTANT SAFETY INFORMATION: Always read this manual first
before attempting to install or use this fireplace. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
7210580100R07
Table of Contents
Welcome & Congratulations . . . . . . . . . . . . . . . . 3
Important Instructions. . . . . . . . . . . . . . . 4
Quick Reference Guide . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . 19
Always use a qualified technician
or service agency to repair
this fireplace.
! NOTE: Procedures and
techniques that are
considered important
enough to emphasize.
CAUTION: Procedures and
techniques which, if not
carefully followed, will result
in damage to the equipment.
Warning: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of fire,
serious injury, or death.
2
www.dimplex.com
Welcome & Congratulations
Thank you and congratulations for choosing to purchase an electric
fireplace from Dimplex, the world leader in electric fireplaces.
Please carefully read and save these instructions.
CAUTION: Read all instructions and warnings carefully before
starting installation. Failure to follow these instructions may result in a
possible electric shock, fire hazard and will void the warranty.
Please record your model and serial numbers below for future
reference: model and serial numbers can be found on the Model and
Serial Number Label of your fireplace.
Model Number
Serial Number
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information?
Product Under Manufacturer’s Warranty?
Contact us at:
OR
 www.dimplex.com/customer_support
For Troubleshooting and Technical Support
 Toll-Free 1-888-DIMPLEX (1-888-346-7539)
Monday to Friday 8:00 a.m. to 4:30 p.m. EST
Please have your model number and product serial number ready. (See above)
3
Important Instructions
When using electrical appliances,
basic precautions should always be
followed to reduce the risk of fire,
electric shock, and injury to persons,
including the following:
① Read all instructions before using
the electric fireplace.
② The heater is hot when in use.
To avoid burns, do not let bare skin
touch hot surfaces. The trim around
the heater outlet becomes hot during
heater operation. Keep combustible
materials, such as furniture, pillows,
bedding, papers, clothes, and
curtains at least 3 feet (0.9 m) from
the front of the unit.
③ Extreme caution is necessary
when any heater is used by or near
children or invalids and whenever the
unit is left operating and unattended.
④ Always unplug the electric
fireplace when not in use.
⑤ Do not operate any unit with
a damaged cord or plug, or if the
heater has malfunctioned, or if the
electric fireplace has been dropped
or damaged in any manner. Return
heater to authorized service facility for
examination, electrical or mechanical
adjustment, or repair.
⑥ Do not use outdoors.
4
⑦ The electric fireplace is not
intended for use in bathrooms,
laundry areas and similar indoor
locations. Never locate heater where
it may fall into a bathtub or other
water container.
⑧ Do not run the cord under
carpeting. Do not cover cord with
throw rugs, runners, or the like.
Arrange cord away from traffic area
and where it will not be tripped over.
⑨ To disconnect the unit, turn the
controls off, then remove the plug
from the outlet.
⑩ Do not insert or allow foreign
objects to enter any ventilation or
exhaust opening as this may cause
an electric shock or fire, or damage to
the heater.
⑪ To prevent a possible fire, do
not block air intake or exhaust in any
manner. Do not use on soft surfaces,
like a bed, where openings may
become blocked.
⑫ All electrical heaters have hot
and arcing or sparking parts inside.
Do not use in areas where gasoline,
paint, or flammable liquids are used
or stored or where the unit will be
exposed to flammable vapors.
⑬ Do not modify the electric
fireplace. Use it only as described
www.dimplex.com
Important Instructions
in this manual. Any other use not
recommended by the manufacturer
may cause fire, electric shock or
injury to persons.
⑭ Avoid the use of an extension
cord. Extension cords may overheat
and cause a risk of fire. If you must
use an extension cord, the cord must
be No. 14 AWG minimum size and
rated no less than 1875 Watts.
⑮ Do not burn wood or other
materials in the electric fireplace.
⑯ Do not strike the fireplace glass.
⑰ Always use a certified electrician
should new circuits or outlets be
required.
⑳ When transporting or storing the
unit and cord, keep in a dry place,
free from excessive vibration and
store so as to avoid damage.
WARNING: Remote control
contains small batteries. Keep away
from children. If swallowed, seek
medical attention immediately.
WARNING: Do not install battery
backwards, charge, put in fire or mix
with used or other battery types - may
explode or leak causing injury.
! NOTE: Changes or modifications
not expressly approved by the party
responsible for compliance could
void user's authority to operate the
equipment.
⑱ Always use properly grounded,
fused and polarized outlets.
⑲ Disconnect all power supply
before performing any cleaning,
maintenance or relocation of the unit.
CAUTION
Risk of electric shock
Do not open
No user-servicable parts inside
SAVE THESE Instructions
5
Quick Reference Guide
① The information regarding the
model of your electric fireplace
can be found on the rating label
located on the top of the firebox.
② If you have any technical
questions or concerns regarding
the operation of your electric
fireplace, or require service
contact customer service.
③ The heater may emit a slight,
harmless odor when first used.
This odor is a normal condition
caused by the initial heating of internal heater parts.
!
NOTE: This equipment has been tested and found to comply with the limits for Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and the receiver.
· Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not cause
interference and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
6
www.dimplex.com
Installation
Site Selection and
Preparation
! NOTE 1: A 15 Amp, 120 Volt
circuit is required. A dedicated
circuit is preferred but not
essential in all cases. A
dedicated circuit will be
required if, after installation,
the circuit breaker trips or
fuse blows on a regular basis
when the heater is operating.
Additional appliances on the
same circuit may exceed the
current rating of the circuit
breaker.
WARNING: Ensure the
power cord is not installed so
that it is pinched or against a
sharp edge and ensure that
the power cord is stored or
secured to avoid tripping or
snagging to reduce the risk of
fire, electric shock or injury to
persons.
①Select a suitable location that
is not susceptible to moisture and
is away from drapes, furniture and
high traffic.
② For ease of electrical hook
fireplace near an existing outlet
(refer to NOTE 1) for plug-in
convenience.
If installing a new outlet for this
electric fireplace:
• Construction and electrical
outlet wiring must comply
with local building codes and
other applicable regulations to
reduce the risk of fire, electric
shock and injury to persons.
• Do not attempt to wire your
own new outlets or circuits.
To reduce the risk of fire,
electric shock or injury to
persons, always use a licensed
electrician.
The dimensions of the firebox are
26 inches (660.5 mm) wide X
18 ⅞ inches (479.5 mm) high
X 8 ¾ inches (223 mm) deep.
The firebox does not require any
additional venting.
For all installation options, ensure
that the fireplace opening has the
following MINIMUM dimensions
(Figure 1):
up you may wish to locate the
7
Installation
Figure 1
C
B
A
A - 9” (229 mm)
B - 24 ½” (622 mm)
C - 18 ¼” (463.6 mm)
Hardwire option
The firebox comes packaged with
a two (2) prong power cord but
allows for an easy conversion for
hardwired installations. Follow
the steps below to hardwire your
firebox.
CAUTION: Use two (2)
conductor, non-metallic sheath
cable with ground wire (3 wires
total) for the incoming power
supply on fireplace inserts.
Use appropriate wire to meet
local and national electrical
codes for rated power
consumption.
②Remove the outer jacket and
strip the individual conductor from
the end.
③ Loosen the screw securing
the junction box cover and
remove the cover.
④ Take the cables out from the
junction box, loosen the two wire
twist nuts and remove the cord
set (Figure 2).
Figure 2
① Wire a dedicated, properly
fused circuit with a 120 Volt,
15 Amp rating. Allow up to
eight (8) feet of service cable
for connecting power supply to
junction box on firebox when
installing.
8
www.dimplex.com
Installation
⑤ Route the power supply wire
through the knockout on supplied
alternative junction box cover
and secure with a wire clamp (not
supplied) (Figure 3).
⑧ Connect the green wire
(ground) from the unit to the
green wire from power supply
(Figure 4).
⑨ Place all connectors inside
the unit and secure the junction
box cover to unit. Ensure that the
cable clamp grips only the jacket
of service cable.
Figure 3
⑥ Connect the black wire (live)
from the unit to the black wire
from power supply (Figure 4).
⑦ Connect the white wire
(neutral) from the unit to the white
wire from power supply (Figure 4).
Figure 4
FIREPLACE
JUNCTION
BOX
WHITE WIRE (N)
WHITE WIRE (N)
BLACK WIRE (L)
BLACK WIRE (L)
GREEN WIRE (G)
GREEN WIRE (G)
120V
POWER
SUPPLY
(BREAKER
PANEL)
9
Installation
Firebox Installation
Install the firebox in one of the
following methods:
① Within a new or existing
mantel. Refer to Figure 1 for
minimum dimension requirements.
② Within a new wall
construction.
New Wall Construction
①Select a suitable location that
is not susceptible to moisture and
is away from drapes, furniture and
high traffic.
② Place the fireplace in the
desired location to see how it will
look in the room.
③Mark the desired location on
the floor and store the fireplace in
a safe, dry and dust free location.
④ Use studs to frame an
near the fireplace.
Option #2 - A new outlet can be
installed inside the new frame
construction. Plug the unit into
a 15 Amp / 120 Volt outlet. If
the cord does not reach, you
may use an extension cord
rated for a minimum of 1875
Watts.
Option #3 - Hardwire
Refer to Hardwire installation
instructions on page 8.
Final Steps
Carefully pour and evenly
distribute the supplied glass
rock media on the front tray of
the firebox (Figure 5). Once
complete, hang the front glass
assembly on the mounts of the
firebox.
Figure 5
opening of 24 ½ inches (622 mm)
wide X 18 ¼ inches (463.6 mm)
high X 9 inches (229 mm) deep.
⑤ Choose a wiring method:
Option #1 - The power cord can
be led from behind the trim
and along the wall to an outlet
10 Mounts
Front glass
Hooks
www.dimplex.com
Operation
Figure 6
C
B
A
supplies power to the heater fan
and the heater element. When the
switch is in the On position, the
heater operates if the thermostat
calls for heat.
C. Heater Thermostat Control
A. Three Position Switch
The switch has two On positions
marked “ I ” and “ II ”.
The “ I ” position is for manual
operation. In this position the
built-in remote control is bypassed.
The “ II ” position is for operating
the unit with the provided remote
control. When in the remote
control (“ II ”) position the unit is
operated with the ON and OFF
buttons of the remote control.
When the switch is in the center
“ O ” position the unit is off.
B. Heater On/Off Switch
To adjust the temperature to your
individual requirements, turn the
thermostat control clockwise all
the way to turn on the heater.
When the room reaches the
desired temperature, turn
the thermostat knob counterclockwise until you hear a click.
Leave in this position to maintain
the room temperature at this
setting. For additional heat, turn
clockwise until you hear the click
again and the heater will turn on.
Resetting the Temperature
Cutoff Switch
Should the heater overheat, an
automatic cut out will turn the
fireplace off and it will not come
back on without being reset. It
can be reset by switching the
Three Position On/Off switch to
Off and waiting five (5) minutes
before switching the unit back on.
The Heater On/Off Switch
11
Operation
CAUTION: If you need to
continuously reset the heater,
disconnect power and call
Dimplex customer service at
1-888-DIMPLEX
(1-888-346-7539).
Remote Operation
The fireplace is supplied with an
integrated on/off remote control
(Figure 7)
Figure 7
On
Button
Off
Button
Battery
Battery
Cover
! Note: Ensure that the
fireplace's Three Position
switch is set to the remote
control (“ II ”) setting
(Figure 6A).
To operate, push the ON button
to turn fireplace on, push the OFF
button to turn the fireplace off.
Battery Replacement (Figure 7)
To replace the battery:
① Slide battery cover open on
12 the hand held transmitter.
② Install one (1) 12-Volt (A23)
battery in the battery holder.
③ Close the battery cover.
Battery must be recycled
or disposed of properly.
Check with your Local
Authority or Retailer for recycling
advice in your area.
Remote Initialization/
Reprogramming
In the event that your remote
control ceases to operate your
fireplace, follow these steps to
re-initialize the remote control and
the remote control receiver in the
fireplace:
① Place the Three Position
Switch (Figure 6A) in the Off
(“ O ”) position.
② Wait a minimum of five (5)
seconds and then place the Three
Position On/Off Switch in the
remote (“ II ”) position.
③ Within 10 seconds of
changing the switch position,
press the ON button located on
the remote control (Figure 7).
www.dimplex.com
Operation
This will synchronize the remote
control and the remote control
receiver.
! NOTE: You will have only 10
seconds to perform this last
step. Failure to do so will result
in these steps needing to be
followed again.
If you are still experiencing issues
with your remote control, contact
Dimplex North America Limited
Customer Service at
1-888-346-7539, or visit the
Dimplex website at
www.dimplex.com.
Maintenance
WARNING:
Disconnect
power before attempting any
maintenance or cleaning to
reduce the risk of fire, electric
shock or damage to persons.
Light Bulb Replacement
Allow at least five (5) minutes for
light bulbs to cool before touching
bulbs to avoid accidental burning
of skin.
Light bulbs need to be replaced
when you notice a dark section
of the flame. There are two (2)
bulbs under the media tray, which
generate the flames.
Light Bulb Requirements
Quantity of two (2) clear
chandelier or candelabra bulbs
with an E-12 (small) socket base,
60 Watt rating. Example: GE
60BC or Philips 60 CTC.
Do not exceed 60 Watts per
bulb.
Helpful Hints
It is a good idea to replace both
light bulbs at one time if they are
close to the end of their rated life.
Group replacement will reduce
the number of times you need
to open the unit to replace light
bulbs. Care must be taken when
removing the media tray.
Replacing Light Bulbs:
① Carefully remove the front
13
Maintenance
glass assembly. Be aware that
some of the glass media may fall
out of the tray (Figure 8).
② Empty the tray of glass media.
CAUTION: Handle glass
media with care as some
pieces may have sharp edges.
⑥ Unscrew bulb(s) counter
clockwise.
⑦ Insert new bulb(s).
⑧ Push flicker rod back onto
motor shaft and replace opposite
end of flicker rod back into
support bracket.
⑨ Replace media tray back into
firebox.
Figure 8
Flicker Rod
⑩ Gently pour and evenly
Glass media
and Tray
spread the glass media.
⑪Replace glass assembly.
Glass Cleaning
Front Glass
Assembly
③ Lift the tray up and remove
from firebox.
④ Pull flicker rod towards the
motor and bend gently to remove
the opposite end from the support
bracket.
⑤ Remove flicker rod from motor
(see Figure 8).
14 The front glass is cleaned in
the factory during the assembly
operation. During shipment,
installation, handling, etc., the
front glass may collect dust
particles, these can be removed
by dusting lightly with a clean dry
cloth.
To remove fingerprints or other
marks, the glass can be cleaned
with a damp cloth. The glass
should be completely dried with
a lint free cloth to prevent water
spots. To prevent scratching,
do not use abrasive cleaners or
www.dimplex.com
Maintenance
spray liquids on the glass surface.
Mantel Surface Cleaning
To remove fingerprints or other
marks, the exterior finish can be
cleaned with a damp cloth with
a mild detergent. The surface
should be completely dried with
a lint free cloth to prevent water
spots.
15
Warranty
Products to which this limited warranty
applies
This limited warranty applies to your newly
purchased Dimplex electric fireplace. This
limited warranty applies only to purchases
made in any province of Canada except
for Yukon Territory, Nunavut, or Northwest
Territories or in any of the 50 States of
the USA (and the District of Columbia)
except for Hawaii and Alaska. This limited
warranty applies to the original purchaser
of the product only and is not transferable.
Products excluded from this limited
warranty
Light bulbs are not covered by this limited
warranty and are the sole responsibility of
the owner/purchaser. Products purchased
in Yukon Territory, Nunavut, Northwest
Territories, Hawaii, or Alaska are not
covered by this limited warranty. Products
purchased in these States, provinces, or
territories are sold AS IS without warranty
or condition of any kind (including, without
limitation, any implied warranties or
conditions of merchantability or fitness for
a particular purpose) and the entire risk of
as to the quality and performance of the
products is with the purchaser, and in the
event of a defect the purchaser assumes
the entire cost of all necessary servicing
or repair.
What this limited warranty covers and for
how long
Products, other than fireplace surrounds
(mantels) and trims, covered by this
limited warranty have been tested and
inspected prior to shipment. Subject to
the provisions of this warranty, Dimplex
warrants such products to be free from
defects in material and workmanship for
16 a period of 2 years from the date of the
first purchase of such products as follows:
(a) a repair or replacement warranty on
defective products or parts, including
in-home services, for the first year
following the date of first purchase; and (b)
thereafter, a replacement of parts warranty
on defective products and parts (with no
in-home services) for the 1 year period
commencing on the first anniversary of
first purchase and ending on the second
anniversary of the date of first purchase.
Dimplex fireplace surrounds (mantels)
and trims covered by this limited warranty
have been tested and inspected prior to
shipment and, subject to the provisions
of this warranty, Dimplex warrants such
products to be free from defects in
material and workmanship for a period of
1 year from the date of first purchase of
such products. Warranty services do not
include in-home services.
The limited 2 year warranty period for
products other than fireplace surrounds
(mantels) and trims and the limited 1 year
warranty period for fireplace surrounds
(mantels) and trims also applies to any
implied warranties that may exist under
applicable law. Some jurisdictions do not
allow limitations on how long an implied
warranty lasts, so the above limitation may
not apply to the purchaser.
What this limited warranty does not cover
This limited warranty does not apply to
products that have been repaired (except
by Dimplex or its authorized service
representatives) or otherwise altered. This
limited warranty does further not apply
to defects resulting from misuse, abuse,
accident, neglect, incorrect installation,
improper maintenance or handling, or
www.dimplex.com
Warranty
operation with an incorrect power source.
What you must do to get service under
this limited warranty
Defects must be brought to the attention of
Dimplex Technical Service by contacting
Dimplex at 1-888-DIMPLEX
(1-888-346-7539), or 1367 Industrial
Road, Cambridge Ontario, Canada
N1R 7G8. Please have proof of purchase,
catalogue/model and serial numbers
available when calling. Limited warranty
service requires a proof of purchase of the
product.
What Dimplex will do in the event of a
defect
In the event a product or part covered
by this limited warranty is proven to be
defective in material or workmanship
during (i) the 2 year limited warranty
period for products other than fireplace
surrounds (mantels) and trims, and (ii)
the 1 year limited warranty period for
surrounds (mantels) and trims, you have
the following rights:
• Limited warranty service will be
performed solely by dealers or service
agents of Dimplex authorized to
provide limited warranty services.
• For products (other than surrounds
(mantels) and trims) for the period
ending at midnight on the first
anniversary of the date of first
purchase, Dimplex will in its sole
discretion either repair or replace
such defective product or part without
charge. If Dimplex is unable to repair
or replace such product or part,
or if repair or replacement is not
commercially practicable or cannot
be timely made, Dimplex may, in lieu
of repair or replacement, choose to
refund the purchase price for such
product or part. This limited warranty
entitles the purchaser to on-site or inhome warranty services. Accordingly,
Dimplex will be responsible for all
labour and transportation costs
associated with the repair or
replacement of the product or part
except as follows: (i) charges may
be levied for travel costs incurred to
travel to the purchaser’s site where the
product is located if the purchaser’s
site is beyond 30 miles (48 km) from
the closest service depot of Dimplex’s
dealer or service agent; and (ii)
the purchaser is solely responsible
for providing clear access to all
serviceable parts of the product.
• For products (other than surrounds
(mantels) and trims) for the period
commencing at 12:01 a.m. on the
day after the first anniversary of
the first purchase and ending at
midnight on the second anniversary
of the date of first purchase, this
limited warranty entitles the purchaser
to replacement parts only without
charge. If Dimplex is unable to replace
such part, or if replacement is not
commercially practicable or cannot
be timely made, Dimplex may, in lieu
of replacement, choose to refund the
purchase price for such part. The
purchaser shall not be entitled to
on-site or in-home warranty services.
The purchaser shall be responsible for
all expenses incurred for the removal
of the part and installation of the
replacement part including, without
limitation, all shipping costs and
transportation costs to and from the
authorized dealer’s or service agent’s
17
Warranty
place of business and all labour
costs. Such costs shall not be the
responsibility of Dimplex.
• For surrounds (mantels) and trims
for the period ending at midnight on
the first anniversary of the date of
first purchase, Dimplex will in its sole
discretion either repair or replace such
defective surrounds (mantels) and
trims or part thereof without charge. If
Dimplex is unable to repair or replace
such product or part, or if repair or
replacement is not commercially
practicable or cannot be timely
made, Dimplex may, in lieu of repair
or replacement, choose to refund
the purchase price for such product
or part. The purchaser shall not be
entitled to on-site or in-house services.
The purchaser is responsible for
all expenses incurred for repair or
replacement of such product or
part including, without limitation, all
shipping costs and transportation
costs to and from the authorized
dealer’s or service agent’s business
and all labour costs. Such costs shall
not be the responsibility of Dimplex.
• On-site or in-home services not
provided under this warranty may be
performed at the purchaser’s specific
request and expense at Dimplex’s
then-current rates for such services.
What Dimplex and its dealers and service
agents are also not responsible for:
SPECIAL, PUNITIVE, EXEMPLARY,
CONSEQUENTIAL, OR INCIDENTAL
LOSS, COST, OR DAMAGE ARISING
OUT OF OR IN CONNECTION WITH
THE SALE, MAINTENANCE, USE, OR
INABILITY TO USE THE PRODUCT,
EVEN IF DIMPLEX OR ITS DIRECTORS,
OFFICERS, OR AGENTS HAVE BEEN
ADVISED OF THE POSSIBILITY OF
SUCH LOSSES, COSTS OR DAMAGES,
OR IF SUCH LOSSES, COSTS, OR
DAMAGES ARE FORESEEABLE. IN
NO EVENT WILL DIMPLEX, OR ITS
OFFICERS, DIRECTORS, OR AGENTS
BE LIABLE FOR ANY DIRECT LOSSES,
COSTS, OR DAMAGES THAT EXCEED
THE PURCHASE PRICE OF THE
PRODUCT.
SOME JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO
THE PURCHASER.
How State and Provincial law apply
This limited warranty gives you specific
legal rights, and you may also have other
rights which vary from jurisdiction to
jurisdiction. The provisions of the United
Nations Convention on Contracts for
the Sale of Goods shall not apply to this
limited warranty or the sale of products
covered by this limited warranty.
IN NO EVENT WILL DIMPLEX, OR ITS
DIRECTORS, OFFICERS, OR AGENTS,
BE LIABLE TO THE PURCHASER OR
ANY THIRD PARTY. WHETHER IN
CONTRACT, IN TORT, OR ON ANY
OTHER BASIS, FOR ANY INDIRECT,
18 www.dimplex.com
Replacement Parts
Blower Assembly (comes with Cutout) . . . . . . . . . . . . . . . . . . . . 2200491100RP
Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000210200RP
Flicker Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5901110100RP
Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2300150100RP*
Two Socket Light Harness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2500400500RP
Heater On/Off Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800070700RP
3-Position Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800071100RP
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000370500RP
Remote Control Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000380200RP
Terminal Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000150100RP
Cord Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4100090104RP
Front Glass Assembly (DFG2562, DFG253A). . . . . . . . . . . . . . 1020230478RP
Front Glass Assembly (DFG2562SS). . . . . . . . . . . . . . . . . . . . 1020230280RP
Partially Reflective Glass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5901410200RP
Control Knob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8801080100RP
Dimplex North America Limited
1367 Industrial Road
Cambridge ON
Canada N1R 7G8
© 2011 Dimplex North America Limited
19
Download PDF