SUSE Linux Enterprise Server www.suse.com 11 SP4

SUSE Linux Enterprise Server www.suse.com 11 SP4
SUSE Linux
Enterprise Server
11 SP4
March 14, 2016
www.suse.com
Deployment Guide
Deployment Guide
Copyright © 2006–2016 SUSE LLC and contributors. All rights reserved.
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU
Free Documentation License, Version 1.2 or (at your option) version 1.3; with the Invariant Section
being this copyright notice and license. A copy of the license version 1.2 is included in the section
entitled “GNU Free Documentation License”.
For SUSE and Novell trademarks, see the Novell Trademark and Service Mark list http://
www.novell.com/company/legal/trademarks/tmlist.html. All other third party
trademarks are the property of their respective owners. A trademark symbol (®, ™ etc.) denotes a
SUSE or Novell trademark; an asterisk (*) denotes a third party trademark.
All information found in this book has been compiled with utmost attention to detail. However, this
does not guarantee complete accuracy. Neither SUSE LLC, its affiliates, the authors nor the translators shall be held liable for possible errors or the consequences thereof.
Contents
About This Guide
xi
1 Available Documentation ........................................................................ xi
2 Feedback ............................................................................................ xiii
3 Documentation Conventions .................................................................. xiv
1 Planning for SUSE Linux Enterprise Server
1
1.1 Considerations for Deployment of a SUSE Linux Enterprise Server ............. 2
1.2 Deployment of SUSE Linux Enterprise Server ......................................... 3
1.3 Running SUSE Linux Enterprise Server .................................................. 4
I Architecture Specific Installation
Considerations
5
2 Installation on x86, AMD64, Intel 64, and Itanium
7
2.1 Required Background ........................................................................... 7
2.2 System Requirements for Operating Linux .............................................. 8
2.3 Installation Considerations ................................................................... 11
2.4 Boot and Installation Media ................................................................. 14
2.5 Installation Procedure ......................................................................... 15
2.6 Controlling the Installation ................................................................... 16
2.7 Dealing with Boot and Installation Problems .......................................... 18
3 Installation on IBM POWER
21
3.1 Requirements ..................................................................................... 21
3.2 Preparation ........................................................................................ 23
4 Installation on IBM System z
39
4.1 General Information and Requirements ................................................. 39
4.2 Preparing for Installation ..................................................................... 46
4.3 Network Connection Types .................................................................. 66
4.4 The parmfile—Automating the System Configuration ............................. 69
4.5 Using the vt220 Terminal Emulator ...................................................... 75
4.6 Further In-Depth Information about IBM System z ................................. 76
II Manual Deployment
79
5 Deployment Strategies
81
5.1 Deploying up to 10 Workstations ......................................................... 81
5.2 Deploying up to 100 Workstations ........................................................ 83
5.3 Deploying More than 100 Workstations ................................................. 91
6 Installation with YaST
93
6.1 Choosing the Installation Method ......................................................... 93
6.2 The Installation Workflow ................................................................... 96
6.3 IBM POWER: System Start-Up for Network Installation ......................... 97
6.4 IBM System z: System Start-Up for Installation ...................................... 97
6.5 System Start-Up for Installation ........................................................... 97
6.6 The Boot Screen on Machines Equipped with Traditional BIOS ................ 98
6.7 The Boot Screen on Machines Equipped with UEFI .............................. 103
6.8 Welcome ......................................................................................... 105
6.9 IBM System z: Hard Disk Configuration .............................................. 106
6.10 Media Check .................................................................................. 108
6.11 Installation Mode ............................................................................ 108
6.12 Clock and Time Zone ...................................................................... 111
6.13 Server Base Scenario ....................................................................... 113
6.14 Installation Settings ......................................................................... 114
6.15 Performing the Installation ............................................................... 119
6.16 Configuration of the Installed System ................................................ 122
6.17 Graphical Login .............................................................................. 133
7 Updating SUSE Linux Enterprise
135
7.1 Terminology .................................................................................... 135
7.2 The SUSE Linux Enterprise 11 Maintenance Model .............................. 137
7.3 Supported Upgrade Paths to SLE SP4 ................................................. 145
7.4 General Preparations for Updating ...................................................... 146
7.5 Updating SLE 11 SP1 to SLE 11 SP2 ................................................. 148
7.6 Updating SLE 11 SP2 to SLE 11 SP3 ................................................. 157
7.7 Updating SLE 11 SP3 to SLE 11 SP4 ................................................. 162
7.8 Backporting Source Code .................................................................. 168
7.9 The Atomic Update .......................................................................... 171
7.10 Migration Hooks for YaST Wagon .................................................... 173
8 Setting Up Hardware Components with YaST
179
8.1 Hardware Information ....................................................................... 179
8.2 Setting Up Graphics Card and Monitor ................................................ 180
8.3 Setting Up Keyboard and Mouse ........................................................ 181
8.4 Setting Up Sound Cards .................................................................... 184
8.5 Setting Up a Printer .......................................................................... 187
8.6 Setting Up a Scanner ........................................................................ 193
9 Installing or Removing Software
195
9.1 Definition of Terms .......................................................................... 195
9.2 Using the KDE Interface (Qt) ............................................................ 197
9.3 Managing Software Repositories and Services ...................................... 203
9.4 Keeping the System Up-to-date .......................................................... 206
10 Installing Add-On Products
213
10.1 Add-Ons ........................................................................................ 213
10.2 Binary Drivers ................................................................................ 214
10.3 SUSE Software Development Kit (SDK) 11 ....................................... 214
11 Accessing the Internet
217
11.1 Direct Internet Connection ............................................................... 217
11.2 Internet Connection Via Network ...................................................... 219
12 Managing Users with YaST
221
12.1 User and Group Administration Dialog .............................................. 221
12.2 Managing User Accounts ................................................................. 223
12.3 Additional Options for User Accounts ............................................... 225
12.4 Changing Default Settings for Local Users ......................................... 232
12.5 Assigning Users to Groups ............................................................... 232
12.6 Managing Groups ............................................................................ 233
12.7 Changing the User Authentication Method ......................................... 234
13 Changing Language and Country Settings with YaST
237
13.1 Changing the System Language ......................................................... 238
13.2 Changing the Country and Time Settings ............................................ 242
14 Remote Installation
245
14.1 Installation Scenarios for Remote Installation ...................................... 245
14.2 Setting Up the Server Holding the Installation Sources ......................... 254
14.3 Preparing the Boot of the Target System ............................................ 263
14.4 Booting the Target System for Installation .......................................... 274
14.5 Monitoring the Installation Process .................................................... 277
15 Advanced Disk Setup
281
15.1 Using the YaST Partitioner .............................................................. 281
15.2 LVM Configuration ........................................................................ 293
15.3 Soft RAID Configuration ................................................................. 299
16 Subscription Management
305
16.1 Using Kernel Parameters to Access an SMT Server ............................. 306
16.2 Configuring Clients Using AutoYaST Profile ...................................... 307
16.3 Configuring Clients Using the clientSetup4SMT.sh Script ..................... 308
16.4 Registering Clients Against SMT Test Environment ............................. 309
III Imaging and Creating Products
17 KIWI
311
313
17.1 Prerequisites for KIWI .................................................................... 313
17.2 Knowing KIWI’s Build Process ......................................................... 314
17.3 Image Description ........................................................................... 314
17.4 Creating Appliances with KIWI ........................................................ 317
17.5 For More Information ..................................................................... 319
18 Creating Add-On Products With Add-on Creator
321
18.1 Creating Images .............................................................................. 321
18.2 Add-On Structure ........................................................................... 322
18.3 For More Information ..................................................................... 323
19 Creating Images with YaST Product Creator
325
19.1 Prerequisites for Product Creator ...................................................... 325
19.2 Creating Images .............................................................................. 325
19.3 For More Information ..................................................................... 327
20 Deploying Customized Preinstallations
329
20.1 Preparing the Master Machine .......................................................... 330
20.2 Customizing the Firstboot Installation ................................................ 330
20.3 Cloning the Master Installation ......................................................... 339
20.4 Personalizing the Installation ............................................................ 339
IV Automated Installations
21 Automated Installation
341
343
21.1 Simple Mass Installation .................................................................. 343
21.2 Rule-Based Autoinstallation .............................................................. 355
21.3 For More Information ..................................................................... 359
22 Automated Upgrade from SUSE Linux Enterprise 11
SP2 to 11 SP3
361
22.1 Preparing the AutoYaST Profile ....................................................... 361
22.2 Running the Automated Upgrade ...................................................... 363
22.3 GRUB Menu Section for Booting into the Upgrade ............................. 364
22.4 Second Stage of the Upgrade ............................................................ 364
22.5 Limitations and Hints ...................................................................... 365
23 Automated Deployment of Preload Images
367
23.1 Deploying system manually from rescue image ................................... 368
23.2 Automated Deployment with PXE Boot ............................................. 369
A GNU Licenses
375
A.1 GNU Free Documentation License ..................................................... 375
About This Guide
Installations of SUSE Linux Enterprise Server are possible in many different ways. It
is impossible to cover all combinations of boot, or installation server, automated installations or deploying images. This manual should help with selecting the appropriate method of deployment for your installation.
Part I, “Architecture Specific Installation Considerations” (page 5)
The standard deployment instructions differ depending on the architecture used.
For differences and requirements regarding the architecture, see this part.
Part II, “Manual Deployment” (page 79)
Most tasks that are needed during installations are described here. This includes
the manual setup of your computer as well as additional software and remote installations.
Part III, “Imaging and Creating Products” (page 311)
Mass installations often require the preparation of images or products furnished
with the features that are needed in this special case. Several options are described that allow the administrator to prepare these deployment methods.
Part IV, “Automated Installations” (page 341)
To do unattended installations, either use the installation with AutoYaST or prepare an image with kiwi or firstboot. This part describes methods to deploy these
installations with a minimum of user interaction.
Many chapters in this manual contain links to additional documentation resources, including additional documentation that is available on the system as well as documentation available on the Internet.
For an overview of the documentation available for your product and the latest documentation updates, refer to http://www.suse.com/doc or to the following section.
1 Available Documentation
We provide HTML and PDF versions of our books in different languages. The following manuals for users and administrators are available for this product:
Deployment Guide (page i)
Shows how to install single or multiple systems and how to exploit the product
inherent capabilities for a deployment infrastructure. Choose from various approaches, ranging from a local installation or a network installation server to a
mass deployment using a remote-controlled, highly-customized, and automated
installation technique.
Administration Guide (↑Administration Guide)
Covers system administration tasks like maintaining, monitoring, and customizing
an initially installed system.
Security Guide (↑Security Guide)
Introduces basic concepts of system security, covering both local and network security aspects. Shows how to make use of the product inherent security software
like AppArmor (which lets you specify per program which files the program may
read, write, and execute), and the auditing system that reliably collects information about any security-relevant events.
Security and Hardening (↑Security and Hardening)
Deals with the particulars of installing and setting up a secure SUSE Linux Enterprise Server, and additional post-installation processes required to further secure and harden that installation. Supports the administrator with security-related
choices and decisions.
System Analysis and Tuning Guide (↑System Analysis and Tuning Guide)
An administrator's guide for problem detection, resolution and optimization. Find
how to inspect and optimize your system by means of monitoring tools and how
to efficiently manage resources. Also contains an overview of common problems
and solutions, and of additional help and documentation resources.
Virtualization with Xen (↑Virtualization with Xen)
Offers an introduction to virtualization technology of your product. It features an
overview of the various fields of application and installation types of each of the
platforms supported by SUSE Linux Enterprise Server as well as a short description of the installation procedure.
Virtualization with KVM for IBM System z (↑Virtualization with KVM for IBM System z)
Offers an introduction to setting up and managing virtualization with KVM (Kernel-based Virtual Machine) on SUSE Linux Enterprise Server. Learn how to manxii
Deployment Guide
age KVM with libvirt or QEMU. The guide also contains detailed information
about requirements, limitations, and support status.
AutoYaST (↑AutoYaST)
AutoYaST is a system for installing one or more SUSE Linux Enterprise systems
automatically and without user intervention, using an AutoYaST profile that contains installation and configuration data. The manual guides you through the basic
steps of auto-installation: preparation, installation, and configuration.
Storage Administration Guide (↑Storage Administration Guide)
Provides information about how to manage storage devices on a SUSE Linux Enterprise Server.
In addition to the comprehensive manuals, several quick start guides are available:
Installation Quick Start (↑Installation Quick Start)
Lists the system requirements and guides you step-by-step through the installation
of SUSE Linux Enterprise Server from DVD, or from an ISO image.
Linux Audit Quick Start
Gives a short overview how to enable and configure the auditing system and how
to execute key tasks such as setting up audit rules, generating reports, and analyzing the log files.
AppArmor Quick Start
Helps you understand the main concepts behind AppArmor®.
Virtualization with Linux Containers (LXC) (↑Virtualization with Linux Containers
(LXC))
Gives a short introduction to LXC (a lightweight “virtualization” method) and
shows how to set up an LXC host and LXC containers.
Find HTML versions of most product manuals in your installed system under /usr/
share/doc/manual or in the help centers of your desktop. Find the latest documentation updates at http://www.suse.com/doc where you can download
PDF or HTML versions of the manuals for your product.
2 Feedback
Several feedback channels are available:
About This Guide
xiii
Bugs and Enhancement Requests
For services and support options available for your product, refer to http://
www.suse.com/support/.
To report bugs for a product component, log in to the Novell Customer Center
from http://www.suse.com/support/ and select My Support > Service
Request.
User Comments
We want to hear your comments about and suggestions for this manual and the
other documentation included with this product. Use the User Comments feature at the bottom of each page in the online documentation or go to http://
www.suse.com/doc/feedback.html and enter your comments there.
Mail
For feedback on the documentation of this product, you can also send a mail to
[email protected] Make sure to include the document title, the product
version, and the publication date of the documentation. To report errors or suggest enhancements, provide a concise description of the problem and refer to the
respective section number and page (or URL).
3 Documentation Conventions
The following typographical conventions are used in this manual:
• /etc/passwd: directory names and filenames
• placeholder: replace placeholder with the actual value
• PATH: the environment variable PATH
• ls, --help: commands, options, and parameters
• user: users or groups
• Alt, Alt + F1: a key to press or a key combination; keys are shown in uppercase as
on a keyboard
• File, File > Save As: menu items, buttons
xiv
Deployment Guide
• #amd64 em64t ipf: This paragraph is only relevant for the architectures amd64,
em64t, and ipf. The arrows mark the beginning and the end of the text block. ◄
#ipseries zseries: This paragraph is only relevant for the architectures System z
and ipseries. The arrows mark the beginning and the end of the text block. ◄
• Dancing Penguins (Chapter Penguins, ↑Another Manual): This is a reference to a
chapter in another manual.
About This Guide
xv
Planning for SUSE Linux
Enterprise Server
1
The implementation of an operating system either in an existing IT environment or as
a completely new rollout must be carefully prepared. SUSE Linux Enterprise Server
11 SP4 provides a variety of new features. It is impossible to describe all the new features here. The following is just a list of major enhancements that might be of interest.
Xen 4.0 Virtualization
Runs many virtual machines on a single server, each with its own instance of an
operating system. For more information, see Virtualization with Xen (↑Virtualization with Xen).
YaST
Several new configuration options have been developed for YaST. These are normally described in the chapters about the technology involved.
SPident
The management utility SPident gives an overview of the installed software base
and clarifies the current service pack level of the system.
Directory Services
Several LDAP-compliant directory services are available:
• Microsoft Active Directory
• OpenLDAP
Planning for SUSE Linux Enterprise Server
1
AppArmor
Harden your System with the AppArmor technology. This service is described in
depth in Part “Confining Privileges with AppArmor” (↑Security Guide).
AIDE
This is an intrusion detection system that can be setup to detect unauthorized
changes to the system.
iSCSI
iSCSI provides an easy and reasonably inexpensive solution for connecting Linux
computers to central storage systems. Find more information about iSCSI in Storage Administration Guide (↑Storage Administration Guide).
Network File System v4
Starting with version 10, SUSE Linux Enterprise Server supports NFS also in version 4. This gives you performance improvements, strong security, and a “stateful” protocol.
Oracle Cluster File System 2
OCFS2 is a general-purpose journaling file system that is fully integrated in the
Linux 2.6 kernel and later. Find an overview of OCFS2 in the High Availability
Guide.
Linux Kernel Crash Dump
Debugging kernel-related problems is now much easier when using Kexec and
Kdump. This technology is available on x86, AMD64, Intel 64, and POWER platforms.
1.1 Considerations for Deployment
of a SUSE Linux Enterprise Server
At the beginning of the planning process, you should try to define the project goals
and needed features. This must always be done individually for each project, but the
questions to answer should include the following:
• How many installations should be done? Depending on this, the best deployment
methods differ. See also Chapter 5, Deployment Strategies (page 81).
2
Deployment Guide
• Will the system run as physical host or as a virtual machine?
• Will the system be in a hostile environment? Have a look at Chapter 1, Security and
Confidentiality (↑Security Guide) to get an overview of consequences.
• How will you get regular updates? All patches are provided online for registered users. Find the registration and patch support database at http://
download.novell.com/patch/finder/.
• Do you need help for your local installation? Novell provides training, support, and
consulting for all topics pertaining to SUSE Linux Enterprise Server. Find more information about this at http://www.novell.com/products/server/.
• Do you need third-party products? Make sure that the required product is also supported on the desired platform. Novell can provide help to support software on different platforms when needed.
1.2 Deployment of SUSE Linux
Enterprise Server
To make sure that your system will run flawlessly, always try to use certified hardware. The hardware certification process is an ongoing process and the database of
certified hardware is updated regularly. Find the search form for certified hardware at
http://developer.novell.com/yessearch/Search.jsp.
Depending on the number of desired installations, it is beneficial to use installation
servers or even completely automatic installations. Have a look at Chapter 5, Deployment Strategies (page 81) for more information. When using Xen virtualization
technologies, network root file systems or network storage solutions like iSCSI should
be considered.
SUSE Linux Enterprise Server provides you with a broad variety of services. Find an
overview of the documentation in this book in About This Guide (↑Administration
Guide). Most of the needed configurations can be made with YaST, the SUSE configuration utility. In addition, many manual configurations are described in the corresponding chapters.
In addition to the plain software installation, you should consider training the end
users of the systems as well as help desk staff.
Planning for SUSE Linux Enterprise Server
3
1.3 Running SUSE Linux Enterprise
Server
The SUSE Linux Enterprise Server operating system is a well-tested and stable system. Unfortunately, this does not prevent hardware failures or other causes for downtime or data loss. For any serious computing task where data loss could occur, a regular backup should be done.
For optimal security and data safety, you should make regular updates of all the operated machines. If you have a mission critical server, you should run a second identical (pre-production) machine where you can apply all changes for testing purposes before doing so in production. This also gives you the possibility of switching machines
in the case of hardware failure.
4
Deployment Guide
Part I. Architecture Specific
Installation Considerations
Installation on x86, AMD64,
Intel 64, and Itanium
2
This chapter describes the steps necessary to prepare for the installation of SUSE Linux Enterprise Server on x86, AMD64, Intel 64, and Itanium computers. It introduces
the steps required to prepare for various installation methods. The list of hardware
requirements provides an overview of supported systems supported by SUSE Linux
Enterprise Server. Find information about available installation methods and several
common known problems. Also learn how to control the installation, provide installation media, and boot with regular methods.
2.1 Required Background
To keep the scope of these guidelines manageable, certain technical assumptions have
been made:
• You have some computer experience and are familiar with common technical
terms.
• You are familiar with the documentation for your system and the network on which
it runs.
• You have a basic understanding of Linux systems.
For an overview of the documentation available for your product and the latest documentation updates, refer to http://www.suse.com/doc.
Installation on x86, AMD64, Intel 64, and Itanium
7
2.2 System Requirements for
Operating Linux
The SUSE® Linux Enterprise Server operating system can be deployed on a wide
range of hardware. It is impossible to list all the different combinations of hardware
SUSE Linux Enterprise Server supports. However, to provide you with a guide to help
you during the planning phase, the minimum requirements are presented here.
If you want to be sure that a given computer configuration will work, find
out which platforms have been certified by SUSE. Find a list at http://
developer.novell.com/yessearch/Search.jsp.
2.2.1 Hardware for x86
Computers based on x86 constitute a cost-effective way of building high-performance
systems. The preconditions for operating SUSE Linux Enterprise Server on this platform are as follows:
CPU
The number of CPUs supported depends on the kernel used. Specifically, these
are as follows:
Table 2.1: CPUs Supported by the Kernel
Kernel
Oldest CPU Type
Maximum Number
of CPUs
kernel-default
PentiumPro, Athlon
32
kernel-pae
Pentium II, Athlon
XP
128
Memory Requirements
A minimum of 512 MB is required. The recommended memory is 1 GB. For a
multiprocessor system, 256 MB per processor is required. Systems with less than
1 GB main memory need additional swap space that extends the virtual memory
to 1 GB.
8
Deployment Guide
Hard Disk Requirements
The disk requirements depend largely on the installation. Commonly, you need
more space than the installation software itself needs to have a system that works
properly. Minimal requirements for different selections are:
System
Hard Disk Requirements
Minimal X Window System
1.2 GB
GNOME Desktop
3.2 GB
KDE Desktop
2.7 GB
All patterns
10 GB
Boot Methods
The computer can be booted for installation from DVD, USB hard drive, or the
network. A special boot server is required to boot over the network. This boot
server can be configured with SUSE Linux Enterprise Server. To use USB hard
drives, the BIOS or firmware must support booting from USB devices. Create a
bootable USB hard drive as described in Table 6.1, “Boot Options” (page 94).
2.2.2 Hardware for Itanium
The Itanium architecture is 64-bit and allows the operation of large servers.
CPU
II (older Itanium CPUs are no longer supported). Dual core CPUs and hyperthreading are also supported.
Maximum Number of CPUs
At most, 4096 CPUs are supported. For the calculation of the CPU count, a dualcore CPU counts as two CPUs and a hyperthreaded CPU with two siblings also counts as two CPUs. 1024 CPUs could mean 512 dual cores, 512 single cores
with hyperthreading, or 256 dual cores with hyperthreading.
Memory
A minimum of 1GB RAM per CPU socket is recommended.
Installation on x86, AMD64, Intel 64, and Itanium
9
Hard Disk Requirements
The disk requirements depend largely on the installation selected. Commonly,
you need more space than the installed software itself needs to have a system that
works properly. Minimal requirements for different selections are:
System
Hard Disk Requirements
Minimal System
4 GB
Recommended
10 GB
Boot Methods
Options for booting the computer depend on the available hardware. All boot
methods available to the machine should work. A special boot server is required
to use PXE boot over the network. This may also be set up with SUSE Linux Enterprise Server.
2.2.3 Hardware for AMD64 and Intel 64
The AMD64 and Intel 64 architectures support the simple migration of x86 software
to 64 bits. Like the x86 architecture, they constitute a value-for-money alternative.
CPU
All CPUs available on the market to date are supported. This includes dual-core
CPUs.
Maximum Number of CPUs
The maximum number of CPUs supported by AMD64 and Intel 64 is 4096.
Memory Requirements
A minimum of 512 MB of memory is required. Requirements depend on the application. However, the minimum recommended is 1024 MB or 512 MB per CPU
on multiprocessor computers. The theoretical upper limit on the amount of memory supported by the kernel is 512 GB.
Hard Disk Requirements
The disk requirements depend largely on the installation selected. The required
space for this architecture is similar to x86 but you should allocate some space for
compatibility libraries. Minimum requirements for different selections are:
10
Deployment Guide
System
Hard Disk Requirements
Minimal X Window System
1.4 GB
GNOME Desktop
3.5 GB
KDE Desktop
3 GB
All patterns
8.5 GB
Boot Methods
The computer can be booted from a CD or a network. A special boot server is required to boot over the network. This can be set up with SUSE Linux Enterprise
Server.
2.2.4 Supported Virtualization Hosts
The i586 and x86_64 version of SUSE Linux Enterprise Server can also be installed
as VM Guests on various virtualization hosts. The following host operating systems
and virtualization platforms are supported:
• KVM on SLES 11 SP2+
• XEN on SLES 10 SP4 / 11 SP1+
• Citrix XenServer 6.0 / 6.1
• Microsoft Windows 2008 SP2+ / 2008 R2+ / 2012+
• Oracle VM 3.0 / 3.1 / 3.2
• VMware ESX 5.1 / ESXi 5.1 / ESX 5.2 / ESXi 5.2
2.3 Installation Considerations
This section encompasses many factors that need to be considered before installing
SUSE Linux Enterprise Server on x86, AMD64, Intel 64, and Itanium hardware.
Installation on x86, AMD64, Intel 64, and Itanium
11
2.3.1 Installation Type
SUSE Linux Enterprise Server is normally installed as an independent operating system. With the introduction of Xen, it is also possible to run multiple instances of
SUSE Linux Enterprise Server on the same hardware. However, the controlling Domain-0 installation for Xen is performed like a typical installation with some additional packages. The installation of Xen guests is described in Chapter 3, Setting Up Virtual Machines (↑Virtualization with Xen).
2.3.2 Boot Methods
Depending on the hardware used, the following boot methods are available for the
first boot procedure (prior to the installation of SUSE Linux Enterprise Server).
Table 2.2: Boot Options
12
Boot Option
Use
CD or DVD drive
The simplest booting method. The
system requires a locally-available
CD-ROM or DVD-ROM drive for
this.
Floppy or USB disks
Find the images required for creating
boot disks on the first CD or DVD
in the /boot directory. See also the
README in the same directory. Booting from a USB memory stick is only
possible if the BIOS of the machine
supports this method.
PXE or bootp
Must be supported by the BIOS or
by the firmware of the system used.
This option requires a boot server in
the network. This task can be handled
by a separate SUSE Linux Enterprise
Server.
Deployment Guide
Boot Option
Use
Hard disk
SUSE Linux Enterprise Server can also be booted from hard disk. For this,
copy the kernel (linux) and the installation system (initrd) from the
/boot/loader directory of the
first CD or DVD onto the hard disk
and add an appropriate entry to the
boot loader.
2.3.3 Installation Source
When installing SUSE Linux Enterprise Server, the actual installation data must be
available in the network, on a hard disk partition, or on a local DVD. To install from
the network, you need an installation server. To make the installation data available,
set up any computer in a Unix or Linux environment as an NFS, HTTP, SMB, or FTP
server. To make the installation data available from a Windows computer, release the
data with SMB.
The installation source is particularly easy to select if you configure an SLP server in
the local network. For more information, see Section 14.2, “Setting Up the Server
Holding the Installation Sources” (page 254).
2.3.4 Installation Target
Most installations are to a local hard disk. Therefore, it is necessary for the hard disk
controllers to be available to the installation system. If a special controller (like a
RAID controller) needs an extra kernel module, provide a kernel module update disk
to the installation system.
Other installation targets may be various types of block devices that provide sufficient
disk space and speed to run an operating system. This includes network block devices
like iSCSI or SAN. It is also possible to install on network file systems that offer the
standard Unix permissions. However, it may be problematic to boot these, because
they must be supported by the initramfs before the actual system can start. Such
installations are useful if there is a need to start the same system in different locations
or if you intend to use Xen features like domain migration.
Installation on x86, AMD64, Intel 64, and Itanium
13
2.3.5 Different Installation Methods
SUSE Linux Enterprise Server offers several different methods for controlling installation:
• Installation on the console
• Installation via serial console
• Installation with AutoYaST
• Installation with KIWI images
• Installation via SSH
• Installation with VNC
By default, the graphical console is used. If you have a large number of similar computers to install, it is advisable to create an AutoYaST configuration file or a KIWI
preload image and make this available to the installation process. See also the documentation for autoyast2 in Chapter 21, Automated Installation (page 343) and
KIWI in Chapter 17, KIWI (page 313).
2.4 Boot and Installation Media
When installing the system, the media for booting and for installing the system may
be different. All combinations of supported media for booting and installing may be
used.
2.4.1 Boot Media
Booting a computer depends on the capabilities of the hardware used and the availability of media for the respective boot option.
Booting from DVD
This is the most common possibility of booting a system. It is straightforward
for most computer users, but requires a lot of interaction for every installation
process.
14
Deployment Guide
Booting from a USB Hard Drive
Depending on the hardware used, it is possible to boot from a USB hard drive. The respective media must be created as described in Table 6.1, “Boot
Options” (page 94).
Booting from the Network
You can only boot a computer directly from the network if this is supported by
the computer's firmware or BIOS. This booting method requires a boot server
that provides the needed boot images over the network. The exact protocol depends on your hardware. Commonly you need several services, such as TFTP and
DHCP or pxeboot. If you need a boot server, also read Section 14.1.3, “Remote
Installation via VNC—PXE Boot and Wake on LAN” (page 249).
2.4.2 Installation Media
The installation media contain all the necessary packages and meta information that
is necessary to install a SUSE Linux Enterprise Server. These must be available to the
installation system after booting for installation. Several possibilities for providing the
installation media to the system are available with SUSE Linux Enterprise Server.
Installation from DVD
All necessary data is delivered on the boot media. Depending on the selected installation, a network connection or add on media may be necessary.
Networked Installation
If you plan to install several systems, providing the installation media over the
network makes things a lot easier. It is possible to install from many common
protocols, such as NFS, HTTP, FTP, or SMB. For more information on how to
run such an installation, refer to Chapter 14, Remote Installation (page 245).
2.5 Installation Procedure
This section offers an overview of the steps required for the complete installation of SUSE® Linux Enterprise Server in the required mode. Part II, “Manual
Deployment” (page 79) contains a full description of how to install and configure
the system with YaST.
Installation on x86, AMD64, Intel 64, and Itanium
15
2.5.1 Booting from a Local
Interchangeable Drive
CD-ROM and floppy drives and USB memory sticks can be used for installation purposes. Adjust your computer to your needs:
1. Make sure that the drive is entered as a bootable drive in the BIOS.
2. Insert the boot medium in the drive and start the boot procedure.
3. The boot menu of the CD, DVD, floppy, or USB disk allows transferring different
parameters to the installation system. See also Section 14.4.2, “Using Custom Boot
Options” (page 275). If the installation should be performed over the network,
specify the installation source here.
4. If unexpected problems arise during installation, use safe settings to boot.
2.5.2 Installing over the Network
An installation server is required to perform the installation by using a network
source. The procedure for installing this server is outlined in Section 14.2, “Setting Up
the Server Holding the Installation Sources” (page 254).
If you have an SLP server, select SLP as the installation source in the first boot
screen. During the boot procedure, select which of the available installation sources to
use.
If the DVD is available on the network, use it as an installation source. In this case,
specify the parameter install=<URL> with suitable values at the boot prompt.
Find a more detailed description of this parameter in Section 14.4.2, “Using Custom
Boot Options” (page 275).
2.6 Controlling the Installation
Control the installation in one of several ways. The method most frequently used is to
install SUSE® Linux Enterprise Server from the computer console. Other options are
available for different situations. Find more information about the available installation methods in Chapter 5, Deployment Strategies (page 81).
16
Deployment Guide
2.6.1 Installation on the Computer
Console
The simplest way to install SUSE Linux Enterprise Server is using the computer console. With this method, a graphical installation program guides you through the installation. This installation method is discussed in detail in Chapter 6, Installation with
YaST (page 93).
You can still perform the installation on the console without a working graphics mode.
The text-based installation program offers the same functionality as the graphical
version. Find some hints about navigation in this mode in Section “Navigation in
Modules” (Chapter 3, YaST in Text Mode, ↑Administration Guide).
2.6.2 Installation Using a Serial Console
For this installation method, you need a second computer that is connected by a null
modem cable to the computer on which to install SUSE Linux Enterprise Server. Depending on the hardware, even the firmware or BIOS of the computer may already be
accessible to the serial console. If this is possible, you can carry out the entire installation using this method. To activate the serial console installation, additionally specify
the parameter console=ttyS0 at the boot prompt after the boot process has completed and before the installation system starts.
On most computers, there are two serial interfaces, ttyS0 and ttyS1. For the installation, you need a terminal program like minicom or screen. To initiate the serial connection, launch the screen program in a local console by entering the following command:
screen /dev/ttyS0 9600
This means that screen listens to the first serial port with a baud rate of 9600. From
this point on, the installation proceeds similarly to the text-based installation over this
terminal.
2.6.3 Installation with SSH
If you do not have direct access to the computer hardware and, for example, the installation should be launched from a management console, control the entire instalInstallation on x86, AMD64, Intel 64, and Itanium
17
lation process over the network. To do this, enter the parameters UseSSH=1 and
SSHPassword=<secret> at the boot prompt. An SSH daemon is then launched
in the system and you can log in to the system as user root with the password “secret”. To connect, use the command ssh -X [email protected]<ipaddr>.
If you do not have a DHCP server available in your local network, manually
assign an IP address to the installation system. Do this by entering the option
HostIP=<ipaddr> at the boot prompt.
As soon as you are logged in to the installation system, launch the actual installation
with the command yast. The installation will start in the graphical mode if DISPLAY is set. This then guides you through the installation. This procedure is described
in detail in Section 14.1.5, “Simple Remote Installation via SSH—Dynamic Network
Configuration” (page 251).
2.6.4 Installation over VNC
If you do not have direct access to the system, but want a graphical installation, install
SUSE Linux Enterprise Server over VNC. This method is described in detail in Section 14.5.1, “VNC Installation” (page 278).
As suitable VNC clients are also available for other operating systems, such as Microsoft Windows and MacOS, the installation can also be controlled from computers
running those operating systems.
2.6.5 Installation with AutoYaST
If you need to install SUSE Linux Enterprise Server on a number of computers with
similar hardware, it is recommended you perform the installations with the aid of AutoYaST. In this case, start by installing one SUSE Linux Enterprise Server and use this
to create the necessary AutoYaST configuration files.
AutoYaST is extensively documented in Chapter 21, Automated
Installation (page 343).
2.7 Dealing with Boot and
Installation Problems
18
Deployment Guide
Prior to delivery, SUSE® Linux Enterprise Server is subjected to an extensive test
program. Despite this, problems occasionally occur during boot or installation.
2.7.1 Problems Booting
Boot problems may prevent the YaST installer from starting on your system. Another
symptom is when your system does not boot after the installation has been completed.
Installed System Boots, Not Media
Change your computer's firmware or BIOS so that the boot sequence is correct.
To do this, consult the manual for your hardware.
The Computer Hangs
Change the console on your computer so that the kernel outputs are visible. Be
sure to check the last outputs. This is normally done by pressing Ctrl + Alt + F10.
If you are unable to resolve the problem, consult the SUSE Linux Enterprise
Server support staff. To log all system messages at boot time, use a serial connection as described in Section 2.6, “Controlling the Installation” (page 16).
The Itanium Boot Loader
If you have manually altered the kernel or initrd on your system, run /sbin/
elilo before shutting down the computer. If you leave out this step, your system may not be bootable.
Boot Disk
The boot disk is a useful interim solution if you have difficulties setting the other configurations or if you want to postpone the decision regarding the final boot
mechanism. A boot disk may also be a suitable solution in connection with OS/2
or Windows NT. Fore more details on creating boot disks, see Section “Creating
Boot CDs” (Chapter 11, The Boot Loader GRUB, ↑Administration Guide).
Virus Warning after Installation
There are BIOS variants that check the structure of the boot sector (MBR) and erroneously display a virus warning after the installation of GRUB or LILO. Solve
this problem by entering the BIOS and looking for corresponding adjustable settings. For example, switch off virus protection. You can switch this option back on
again later. It is unnecessary, however, if Linux is the only operating system you
use.
Installation on x86, AMD64, Intel 64, and Itanium
19
2.7.2 Problems Installing
If an unexpected problem occurs during installation, information is needed to determine the cause of the problem. Use the following directions to help with troubleshooting:
• Check the outputs on the various consoles. You can switch consoles with the key
combination Ctrl + Alt + Fn. For example, obtain a shell in which to execute various commands by pressing Ctrl + Alt + F2.
• Try launching the installation in failsafe mode. If the installation works without
problems in this case, there is an incompatibility that causes either ACPI or APIC
to fail. In some cases, a BIOS or firmware update fixes this problem.
• Check the system messages on a console in the installation system by entering the
command dmesg.
2.7.3 Redirecting the Boot Source to the
Boot DVD
To facilitate the installation process and avoid accidental installations, the default setting on the installation DVD for SUSE Linux Enterprise Server is that your system is
booted from the first hard disk. At this point, an installed boot loader normally takes
over control of the system. This means that the boot DVD can stay in the drive during
an installation. To start the installation, choose one of the installation possibilities in
the boot menu of the media.
20
Deployment Guide
Installation on IBM POWER
This chapter describes the procedure for preparing the installation of SUSE® Linux
Enterprise Server on IBM POWER systems.
3
3.1 Requirements
A standard installation requires at least 256 MB of RAM. The installation of a standard system requires at least 2.0 GB of free hard disk space.
3.1.1 Hardware Requirements
The SUSE® Linux Enterprise Server operating system can be operated on a wide
range of hardware. To provide you with a guide to help you during the planning phase,
the minimum requirements are presented here.
If you want to be sure that a given computer configuration will work, check the database of hardware certified by SUSE. Find a list of certified hardware at http://
developer.novell.com/yessearch/Search.jsp.
SUSE Linux Enterprise Server may support additional IBM POWER systems not listed below. For the latest information, see the IBM Information Center for Linux at
http://publib.boulder.ibm.com/infocenter/lnxinfo/v3r0m0/
index.jsp?topic=%2Fliaam%2Fliaamdistros.htm.
Find up-to-date firmware at IBM FixCentral (http://www.ibm.com/sup​
port/fixcentral/). Select your system from the Product Group list.
Installation on IBM POWER
21
All systems listed below are operated with a PPC64 kernel.
3.1.1.1 IBM POWER7 Systems
POWER7 systems
• Power 710 Express
• Power 720 Express
• Power 730 Express
• Power 740 Express
• Power 750 Express
• Power 755
• Power 770
• Power 780
• Power 795
POWER7 BladeCenter Models
• IBM BladeCenter PS700
• IBM BladeCenter PS701
• IBM BladeCenter PS702
• IBM BladeCenter PS703
• IBM BladeCenter PS704
3.1.1.2 IBM PowerLinux Systems
• IBM PowerLinux 7R2
3.1.1.3 IBM POWER5 and POWER6 Systems
POWER5 Systems
• OpenPower 710
22
Deployment Guide
• System p5 520
• System i5 520
POWER6 Systems
• IBM Power 550
• IBM Power 570
POWER6 BladeCenter models
• IBM BladeCenter JS12
• IBM BladeCenter JS22
• IBM BladeCenter JS23
• IBM BladeCenter JS43
3.2 Preparation
This section describes the preparatory steps that must be taken before the actual installation. The installation procedure depends on the system used. See the following
documentation:
• For IBM eServer p5 Systems, see Section 3.2.1, “Preparing for Installation on IBM
eServer p5, System p, and OpenPower Models” (page 24)
• For IBM pSeries systems, see Section 3.2.2, “Preparing for Installation on IBM
pSeries Models” (page 31)
• For IBM JS20/JS21/JS22 Blades, see Section 3.2.3, “Preparing an Installation on
IBM JSxx BladeCenter” (page 35)
If SUSE® Linux Enterprise Server needs to be installed on a number of systems or
partitions, it is recommended you create a network installation source. The same
source can also be used for the concurrent installation on several partitions or several systems. The configuration of a network installation source is described in Section 14.2.1, “Setting Up an Installation Server Using YaST” (page 254).
Installation on IBM POWER
23
The installation can be controlled with a VNC client. For more information about
VNC, see Section 14.1.1, “Simple Remote Installation via VNC—Static Network
Configuration” (page 246).
To participate in the linuxppc-dev mailing list, sign up using the forms at
http://lists.ozlabs.org/listinfo/linuxppc-dev/. The following
links are pertinent to the maintenance of an installation:
• http://www.novell.com/support/products/server/ is an effective help tool for assisting customers in solving problems. A corresponding article
is published whenever SUSE discover that a special case could lead to serious problems. Search the portal using keywords like PPC or POWER.
• Find security alerts at http://www.suse.com/support/security/.
SUSE also maintains two security-related mailing lists to which anyone may subscribe.
• suse-security — General discussion of security regarding Linux and
SUSE. All security alerts for SUSE Linux Enterprise Server are sent to this
list.
• suse-security-announce — The SUSE mailing list exclusively for
security alerts.
3.2.1 Preparing for Installation on IBM
eServer p5, System p, and OpenPower
Models
This section covers the preparatory steps for installing SUSE® Linux Enterprise Server on IBM eServer p5 systems. It explains the installation from a built-in CD-ROM
drive and over the network.
This section assumes you have set up your HMC and connected it to your system. Find more information about using the wizard to configure the HMC
in “Configuring the HMC using the Guided Setup Wizard”: http://
publib.boulder.ibm.com/infocenter/systems/scope/hw/top​
ic/iphai_p5/confighmcgs.htm?
24
Deployment Guide
3.2.1.1 Modern Features of IBM eServer p5
Systems
IBM eServer p5 systems offer the possibility of partitioning the system. This enables
the concurrent operation of up to 254 operating systems on one machine. These operating systems are installed in LPARs (logical partitions). One or several of these partitions can contain a SUSE Linux Enterprise Server environment.
To prepare an LPAR for SUSE Linux Enterprise Server, first configure the system over the HMC. Refer to the IBM documentation for details: http://
publib.boulder.ibm.com/infocenter/systems/scope/hw/top​
ic/iphbi/iphbikickoff.htm
3.2.1.2 Hard Disk Space
Make sure that you have sufficient hard disk space for installing SUSE Linux Enterprise Server. The standard system requires at least 4 GB of free hard disk space.
3.2.1.3 Assigning an Installation Device to an
LPAR
SUSE Linux Enterprise Server can be installed from a CD-ROM or DVD drive or using a network installation source. Make the CD-ROM, DVD drive, or network device
available to the LPAR to install.
Installation on IBM POWER
25
Figure 3.1: HMC: Server Management—Properties
Procedure 3.1: Assigning a CD-ROM or DVD Drive to an LPAR
1 Open the HMC application and go to Server and Partition > Server Management.
2 From the available servers, expand the server and partition to install.
3 Right-click the profile to use for installation and select Properties—see Figure 3.1,
“HMC: Server Management—Properties” (page 26).
4 In the Logical Partition Profile Properties dialog, select the Physical I/O tab.
5 From Managed system I/O devices, select the Other Mass Storage Controller from
the bus where it is installed. To assign this DVD drive to the partition, click Add as
required.
The result should look like Figure 3.2, “HMC: Managed System I/O
Devices” (page 27).
26
Deployment Guide
Figure 3.2: HMC: Managed System I/O Devices
Now insert the SUSE Linux Enterprise Server CD1 or DVD1 in the drive.
Procedure 3.2: Assigning a Network Device to an LPAR
1 Open the HMC application and go to Server and Partition > Server Management.
2 From the available servers, open the server and partition to install.
3 Right-click the profile to use for installation and select Properties—see Figure 3.1,
“HMC: Server Management—Properties” (page 26).
4 In the Logical Partition Profile Properties dialog, select the Physical I/O tab.
5 From Managed system I/O devices, select PCI 10/100/1000Mbps Ethernet UTP 2port from the bus where it is installed. Then click Add as required.
If you plan to install using a virtual ethernet adapter, refer to the IBM documentation.
Create a network installation source if SUSE Linux Enterprise Server should be installed on a number of partitions. This eliminates the need to change CDs during inInstallation on IBM POWER
27
stallation. The same source can also be used for concurrent installation of various
systems. The configuration of the network installation source is described in Section 14.2.1, “Setting Up an Installation Server Using YaST” (page 254).
3.2.1.4 Starting the Installation
To start the installation, reboot the system. Right-click the profile name, select Activate, and press OK in the following dialog.
Use the screen console or connect to a serial console as described in the IBM documentation. One simple way to start a serial console is to open a VTerm while activating the partition. To do this, activate Open a terminal window or console session in the
Activate Logical Partition dialog.
Enter the system firmware by pressing F1 or 1 when using a serial console or a virtual
console during the system check when the system is rebooted:
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
1 = SMS Menu
8 = Open Firmware Prompt
memory
keyboard
network
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
5 = Default Boot List
6 = Stored Boot List
scsi
speaker
Press F1 or 1 while the SCSI devices are checked. Select 5. Select Boot Options to enter the boot options dialog:
Version SF220_004
SMS 1.5 (c) Copyright IBM Corp. 2000,2003 All rights reserved.
--------------------------------------------------------------------Main Menu
1. Select Language
2. Setup Remote IPL (Initial Program Load)
3. Change SCSI Settings
4. Select Console
5. Select Boot Options
28
Deployment Guide
--------------------------------------------------------------------Navigation Keys:
X = eXit System Management Services
--------------------------------------------------------------------Type the number of the menu item and press Enter or select Navigation
Key:5
Select 1. Select Install/Boot Device to set the Install Device. Go to 7. List all Devices to
see the list of available devices:
Version SF220_011
SMS 1.5 (c) Copyright IBM Corp. 2000,2003 All rights reserved.
-------------------------------------------------------------------------Select Device
Device Current Device
Number Position Name
1.
Virtual Ethernet
( loc=U9111.520.10D3CCC-V1-C3-T1 )
2.
Ethernet
( loc=U787A.001.DNZ00XG-P1-T5 )
3.
Ethernet
( loc=U787A.001.DNZ00XG-P1-T6 )
4.
IDE CD-ROM
( loc=U787A.001.DNZ00XG-P4-D3 )
5.
1
SCSI 73407 MB Harddisk
( loc=U787A.001.DNZ00XG-P1-T10-L8-L0 )
-------------------------------------------------------------------------Navigation keys:
M = return to Main Menu
ESC key = return to previous screen
X = eXit System Management Services
-------------------------------------------------------------------------Type the number of the menu item and press Enter or select Navigation Key:
3.2.1.5 Booting from the CD-ROM Drive
Select the CD-ROM drive (4 in this example):
SMS 1.5 (c) Copyright IBM Corp. 2000,2003 All rights reserved.
-------------------------------------------------------------------------Select Task
IDE CD-ROM
( loc=U787A.001.DNZ00XG-P4-D3 )
1.
2.
Information
Normal Mode Boot
Installation on IBM POWER
29
3.
Service Mode Boot
-------------------------------------------------------------------------Navigation keys:
M = return to Main Menu
ESC key = return to previous screen
X = eXit System Management Services
-------------------------------------------------------------------------Type the number of the menu item and press Enter or select Navigation Key:
Choose 2. Normal Mode Boot to install from this device. On the next screen, confirm
with 1. Yes to exit System Management Services and boot from the device.
The system reads from the CD-ROM drive and the yaboot utility starts:
Welcome to SuSE:SLE-11:GA!
Type
Type
Type
"install"
"slp"
"rescue"
to start the YaST installer on this CD/DVD
to start the YaST install via network
to start the rescue system on this CD/DVD
Welcome to yaboot version 1.3.11.SuSE
Enter "help" to get some basic usage information
boot:
Type install and press Enter.
To read the installation data from a network install source rather than continuing the
installation from the CD-ROM (see Section 3.2.1.3, “Assigning an Installation Device
to an LPAR” (page 25)), append the option manual to the name of the kernel
(install).
For an installation over VNC, append the parameters vnc=1 and
vncpassword=password to the name of the kernel (install). Read more
about VNC in Section 14.1.1, “Simple Remote Installation via VNC—Static Network
Configuration” (page 246).
3.2.1.6 Booting from the Network Source
Select an ethernet device that has access to the installation source (2 in this example).
30
Deployment Guide
3.2.1.7 Additional Steps
Proceed as described in Chapter 6, Installation with YaST (page 93) to begin installing the software with linuxrc and YaST.
3.2.2 Preparing for Installation on IBM
pSeries Models
This section covers the preparatory steps for installing SUSE® Linux Enterprise Server on pSeries systems. It explains the installation from a built-in CD-ROM drive or a
network source.
3.2.2.1 Special Features of IBM pSeries p630,
p655, p670, and p690
IBM p630, p655, p670, and p690 systems offer the possibility of statically partitioning the system similarly to eServer p5/System p5 (which is described in Section 3.2.1, “Preparing for Installation on IBM eServer p5, System p, and OpenPower
Models” (page 24)). This enables the concurrent operation of up to 16 operating
systems on one machine. These operating systems are installed in LPARs (logical partitions). One or several of these partitions can contain a SUSE Linux Enterprise Server environment.
To prepare an LPAR for SUSE Linux Enterprise Server, first configure the system over the HMC. Refer to the Redbook IBM eServer pSeries 690 System Handbook (SG24-7040-00) for details (http://www.redbooks.ibm.com/red​
books/SG247040/).
Important notes regarding the configuration:
• The recommended maximum number of processors for a SUSE Linux Enterprise
Server LPAR is eight, because the kernel can only manage eight processors effectively.
• For the installation, select SMS as the boot mode for the respective partition.
• The HMC terminal used for the input during the installation is a VT320 emulation.
This emulation can lead to strange results with some applications. If possible, use an
XTerm for communicating with the LPAR.
Installation on IBM POWER
31
3.2.2.2 Hard Disk Space
Make sure that you have sufficient hard disk space for installing SUSE Linux Enterprise Server. The use of a separate hard disk is recommended.
SUSE Linux also supports installing to Fibre Channel–attached storage. Before beginning installation, the Fibre Channel Host Bus Adapter (FCHBA), SAN fabric, and
storage system must each be configured to provide access from the FCHBA through
the SAN Fabric to target logical units (LUNs) on the storage system.
SAN storage devices, if properly configured, are listed among existing hard disks on
your system. Create Custom Partitioning Setup opens the dialog, as described in Section 15.1, “Using the YaST Partitioner” (page 281).
3.2.2.3 Setting Up the Installation Source
If you plan to install from CD-ROM, insert CD1 in the drive. In LPAR mode, the partition to install must have the CD-ROM in its partition profile. Create a network installation source if SUSE Linux Enterprise Server needs to be installed over a number
of partitions. This eliminates the need to change CDs during installation. The same
source can also be used for concurrent installation of various systems. The configuration of the network installation source is described in Section 14.2.1, “Setting Up an
Installation Server Using YaST” (page 254).
3.2.2.4 Starting the Installation
To start the installation, reboot the system. Then enter the system firmware by pressing F1 or 1 when using the serial console during the system check when the system is
rebooted. See Figure 3.3, “Entering the System Firmware” (page 33).
32
Deployment Guide
Figure 3.3: Entering the System Firmware
1 = SMS Menu
5 = Default Boot List
Press F1 or 1 while the SCSI devices are checked. Select 6 MultiBoot to enter the
Multiboot dialog. See Figure 3.4, “Multiboot Dialog” (page 33).
Figure 3.4: Multiboot Dialog
Version M2P01113
(c) Copyright IBM Corp. 2000
All rights reserved.
-----------------------------------------------------------------------Multiboot
1
Select Software
2
Software Default
3
Select Install Device
4
Select Boot Devices
5
OK Prompt
6
Multiboot Startup <ON>
Installation on IBM POWER
33
Select 3 to set the install device. A list of available devices is displayed. See Figure 3.5, “Installing the Operating System” (page 34).
Figure 3.5: Installing the Operating System
Install Operating System
Device Device
Number Name
1
Diskette
2
SCSI Tape id=0 ( slot=50322f5a )
3
SCSI CD-ROM id=1 ( slot=50322f5a )
4
Ethernet
5
SysKonnect PCI FDDI Adapter
6
Ethernet
7
( Integrated )
( slot=4 )
( slot=2 )
None
3.2.2.5 Booting from the CD-ROM Drive
Select the respective CD-ROM drive (3 in this example). The system reads from the
CD-ROM drive and displays the identstring.
->1
SuSE:SLE-11:GA<-
After you select 1, the yaboot utility is started.
Welcome to SuSE:SLE-11:GA!
Type
Type
Type
"install"
"slp"
"rescue"
to start the YaST installer on this CD/DVD
to start the YaST install via network
to start the rescue system on this CD/DVD
Type install and press Enter. Alternatively, just press Enter to start the installer, the
default option.
34
Deployment Guide
To install from a network source (see Section 3.2.2.3, “Setting Up the Installation
Source” (page 32)), append manual to the kernel to install. For an installation over VNC, append the parameters vnc=1 and vncpassword=password to
install. Read more about VNC in Section 14.1.1, “Simple Remote Installation via
VNC—Static Network Configuration” (page 246).
In LPAR mode, the partition to install must have the CD-ROM in its partition profile.
3.2.2.6 Booting from the Network Source
Select an ethernet device that has access to the installation source (6 in this example).
3.2.2.7 Additional Steps
Proceed as described in Chapter 6, Installation with YaST (page 93) to begin installing the software with linuxrc and YaST.
3.2.3 Preparing an Installation on IBM
JSxx BladeCenter
This section describes the preparatory steps for the installation of SUSE® Linux Enterprise Server on JSxx Blades. It covers installation using the CD-ROM drive of the
BladeCenter and using the network.
3.2.3.1 Creating a Network Installation Source
Create a network installation source if SUSE Linux Enterprise Server needs to be
installed over a number of partitions. This provides the advantage of no CDs needing to be changed during installation. The same source can also be used for the
concurrent installation of various systems. Configuration of a network installation source is described in Section 14.2.1, “Setting Up an Installation Server Using
YaST” (page 254).
3.2.3.2 Hard Disk Storage Space
Ensure that enough hard disk storage space is available for the installation of SUSE
Linux Enterprise Server. It is recommended you use a dedicated hard disk.
Installation on IBM POWER
35
3.2.3.3 Preparing the System for Boot
Preparing to Boot from the CD-ROM Drive
Perform the steps described in this section if an installation from CD-ROM is desired.
Assign the CD-ROM drive to the Blade chosen for installation by connecting (with a
Web browser) to a BladeCenter Management Module, then logging in. After login, select the function Remote Control in the menu Blade Tasks then activate Start Remote
Control. Assign the CD-ROM drive to the desired blade in the menu Change Media
Tray Owner of the new window.
Set up the CD-ROM drive as a boot device. Do this by selecting Blade Tasks then
Configuration while in the BladeCenter Management Module. Select the JSxx Blade
in the section Boot Sequence. Set the entry for 1st Device on the page for Blade Boot
Sequence to CDROM.
Put CD 1 in the CD-ROM drive and restart the blade.
Preparing to Boot from the Network
Perform the steps as described in this section if an installation over the network is desired.
Connect to the BladeCenter Management Module using a Web browser and log in. Set
the boot device to the network by accessing the Configuration menu from the Blade
Tasks page. Select the JSxx Blade in the section Boot Sequence and set 1st Boot Device
to Network — BOOTP on Blade Boot Sequence.
Rebooting and Connecting to the Console of the JSxx
Blade
Reboot the JSxx Blade from the item Power/Restart of the Blade Tasks menu in the
BladeCenter Management Module. A table appears, showing the power status of the
blades in the Pwr column. Mark the check box of the desired blade and restart it with
Power On Blade.
Connect to the BladeCenter with the command telnet bladecenter and log in.
36
Deployment Guide
username: user
password: ********
system>
The command env -T system:blade[bay number] determines for which
JSxx Blade the subsequent commands are intended. The blades installed in the BladeCenter are listed by calling list -l 3.
system> list -l 3
system
mm[1]
primary
power[1]
power[2]
power[3]
power[4]
blower[1]
blower[2]
switch[1]
switch[3]
blade[1]
sp
cpu[1]
cpu[2]
blade[3]
sp
blade[4]
sp
blade[6]
sp
blade[8]
sp
cpu[1]
cpu[2]
blade[9]
sp
cpu[1]
cpu[2]
blade[10]
sp
blade[11]
sp
blade[13]
sp
mt
system>
The command target is then determined. To work, for example, with blade number 9,
enter env -T system:blade[9]. Connect with the console of the JSxx Blade
over Serial over LAN (SOL) with the command console.
Installation on IBM POWER
37
system> env -T system:blade[9]
OK
system:blade[9]> console
Starting the Installation
The SUSE Linux Enterprise Server boot loader starts after the system check has completed.
Welcome to SuSE:SLE-11:GA!
Type
Type
Type
"install"
"slp"
"rescue"
to start the YaST installer on this CD/DVD
to start the YaST install via network
to start the rescue system on this CD/DVD
Welcome to yaboot version 1.3.11.SuSE
Enter "help" to get some basic usage information
boot:
Select install from the menu and press Enter.
In the case of an installation over VNC, append the parameters vnc=1 and
vncpassword=password to the command line for the kernel (install).
Additional Steps
Proceed as described in Chapter 6, Installation with YaST (page 93) to begin installing the software with linuxrc and YaST.
38
Deployment Guide
Installation on IBM System
z
4
This chapter describes the procedure for preparing the installation of SUSE® Linux
Enterprise Server on IBM System z systems. It provides all information needed to prepare the installation on the LPAR and z/VM side.
4.1 General Information and
Requirements
This section gives basic information about the system requirements (like supported
hardware), level of MicroCode, and software. It also covers the different installation
types, how to do an IPL for the first installation, and information about the IOCDS.
4.1.1 System Requirements
This section provides a list of hardware for IBM System z supported by SUSE Linux
Enterprise Server. Next, the level of the MicroCode (MCL) used in your IBM System
z system, which is very important for the installation, is covered. Additional software
to install and use for installation is mentioned at the end of this section.
4.1.1.1 Hardware
SUSE Linux Enterprise Server has run successfully on the following platforms:
Installation on IBM System z
39
• IBM Series z9 (z9-EC) 2094
• IBM Series z9 (z9-BC) 2096
• IBM Series z10 (z10-EC) 2097
• IBM Series z10 (z10-BC) 2098
• IBM zEnterprise System z196 2817
• IBM zEnterprise System z114 2818
• IBM zEnterprise EC12 (zEC12) 2827
Memory Requirements
Different installation methods have different memory requirements during installation. After installation is completed, the system administrator may reduce memory to
the desired size. SUSE recommends using:
768 MB
For installation under z/VM.
1 GB
For installation under LPAR.
NOTE: Memory Requirements with Remote Installation Sources
For installation from NFS, FTP, or SMB installation sources or whenever
VNC is used, 512MB of memory is required as a minimum. Otherwise, the installation attempt is likely to fail. Further note that the number of devices visible to the z/VM guest or LPAR image affects memory requirements. Installation with literally hundreds of accessible devices (even if unused for the installation) may require more memory.
Disk Space Requirements
The disk requirements depend largely on the installation. Commonly, you need more
space than the installation software itself needs to have a system that works properly.
Minimal requirements for different selections are:
40
Deployment Guide
2.6 GB
Default Installation
3.6 GB+
Recommended (this is with graphical
desktop, development packages and
Java).
Network Connection
A network connection is needed to communicate with your SUSE Linux Enterprise
Server system. This can be one or more of the following connections or network
cards:
• OSA Express Ethernet (including Fast and Gigabit Ethernet)
• HiperSockets or Guest LAN
• 10 GBE, VSWITCH
The following interfaces are still included, but no longer supported:
• CTC (or virtual CTC)
• ESCON
• IP network interface for IUCV
IPL Options
For an LPAR installation, the Load from CD-ROM or Server option is the preferred
way to IPL the installation kernel and initrd (initial RAM disk). If this option is not
available and you cannot use z/VM for installing the system, you need to IPL from a
channel attached tape with the tapeipl kernel, the parmfile, and the initrd. Thus, you
need access to a tape unit (3480, 3490, or 3590, for example).
4.1.1.2 MicroCode Level, APARs, and Fixes
Documentation about restrictions and requirements for this release of
SUSE Linux Enterprise Server can be found on IBM developerWorks
Installation on IBM System z
41
at http://www.ibm.com/developerworks/linux/lin​
ux390/documentation_suse.html. It is recommended always to use the
highest service level available. Contact your IBM support for minimum requirements.
z/VM
z/VM 5.4
z/VM 6.2
Negotiate the order of installation with your IBM support, because it might be necessary to activate the VM APARs before installing the new MicroCode levels.
4.1.1.3 Software
To install SUSE Linux Enterprise Server via non-Linux–based NFS or FTP, you
might experience problems with NFS or FTP server software. The Windows standard
FTP server can cause errors, so installing via SMB on these machines is generally recommended.
To connect to the SUSE Linux Enterprise Server installation system, one of the following methods is required:
SSH with Terminal Emulation (xterm compatible)
SSH is a standard Unix tool that should be present on any Unix or Linux system.
For Windows, there is an SSH client called Putty. It is free to use and is available
from http://www.chiark.greenend.org.uk/~sgtatham/putty/.
VNC Client
For Linux, a VNC client called vncviewer is included in SUSE Linux Enterprise
Server as part of the tightvnc package. For Windows, tightvnc is also available. Download it from http://www.tightvnc.com/. Alternatively, use
the VNC Java client and a Java-enabled Web browser.
X Server
Find a suitable X server implementation on any Linux or Unix workstation.
There are many commercial X Window System environments for Windows
and Macintosh. Some of them can be downloaded as free trial versions. A trial
version of the Mocha X Server from MochaSoft can be obtained at http://
www.mochasoft.dk/freeware/x11.htm.
42
Deployment Guide
TIP: Additional Information
Consult the README located in the root directory of DVD 1 of your SUSE Linux Enterprise Server before installing SUSE Linux Enterprise Server on IBM
System z. This file completes the documentation presented in this book.
4.1.2 Installation Types
This section gives an overview of the different types of installation possible with
SUSE Linux Enterprise Server for IBM System z. Basically, these two types are given:
LPAR
Installation of SUSE Linux Enterprise Server using a logical partition (LPAR).
VM (z/VM)
Installation of SUSE Linux Enterprise Server as as a guest operating system within z/VM.
Depending on the mode of installation (LPAR or VM), there are different possibilities for starting the installation process and IPLing the installed system.
4.1.2.1 LPAR
If you install SUSE Linux Enterprise Server for IBM System z into a separate logical partition (LPAR), allow SUSE Linux Enterprise Server to use a special part of the
physical memory in your system. Also decide how many processors are used by SUSE
Linux Enterprise Server. In this mode, you can run different operating systems simultaneously on your IBM System z system.
4.1.2.2 z/VM
Running SUSE Linux Enterprise Server for IBM System z in z/VM means that SUSE
Linux Enterprise Server is a guest system within z/VM. An advantage of this mode
is that you have full control over SUSE Linux Enterprise Server from z/VM. This is
very helpful for kernel development or kernel-based debugging. It is also very easy to
add or remove hardware to and from Linux guests. Creating additional SUSE Linux
Enterprise Server guests is simple and you are able to run hundreds of Linux instances
simultaneously.
Installation on IBM System z
43
4.1.3 IPL Options
This section provides the information needed to do an IPL for the first installation.
Depending on the type of installation, different options need to be used. The channel-attached tape, VM reader, and load from CD-ROM or server options are discussed. Installing the software packages, which is done over the network, does not require the IPL medium.
4.1.3.1 ESCON or FICON Attached Tape
IPLing from a channel-attached tape is possible on all systems connected to a tape library. The only prerequisite is that the LPAR in which to install (or allowing z/VM
to run) is allowed to access the tape unit. For this, the IODEVICE statement in the
IOCDS must have the attribute SHARED or PART=<LPARName>.
4.1.3.2 VM Reader
To IPL from a VM reader, transfer the necessary files into the reader first. Then multiple IPLs are easily done. This is the preferred way on z/VM. For convenience of
administration, it is recommended to create a user linuxmnt that owns a minidisk
with the files and scripts needed for IPL. This minidisk is then accessed read-only by
the Linux guests.
4.1.3.3 Load from CD/DVD-ROM or Server
For IPLing into an LPAR, it is possible to either load the kernel image directly from
the SE's or the HMC's CD/DVD-ROM device or from any remote system accessible
through FTP. This function can be performed from the HMC. The installation process
requires a file with a mapping of the location of the installation data in the file system
and the memory locations where the data is to be copied. For SUSE Linux Enterprise
Server this file is called suse.ins and located in the root directory of the file system on the DVD 1.
In the left navigation pane of the HMC expand Systems Management and Servers and
select the mainframe system you want to work with. Choose the LPAR where you
want to boot SUSE Linux Enterprise Server from the table of LPARs displayed in the
upper content area on the right. In the Tasks area, expand Recovery and click Load
from CD-ROM, DVD, or Server.
44
Deployment Guide
Now either choose Hardware Management Console CD-ROM/DVD or FTP Source. If
having chosen the latter option, provide the servers address or name and your credentials. In case the suse.ins file is not located in the root directory of the server, provide the path to this file. Continue to the Select the software to load menu and select
the suse.ins entry. Start the installation with OK.
4.1.3.4 Load from SCSI-Attached DVD
To IPL from a SCSI DVD, you need access to an FCP adapter connected to a DVD
drive. You need values like the WWPN and LUN from the SCSI drive. For details,
see Section “IPL from FCP-Attached SCSI DVD” (page 56).
4.1.3.5 Load from the Network with zPXE
IPLing from the Network with zPXE requires a Cobbler server providing the kernel, RAM disk and a parmfile. zPXE is only available on z/VM and is initiated by
running the ZPXE EXEC script. See Section 4.2.1.3, “Using a Cobbler Server for
zPXE” (page 50) for details.
4.1.4 The IOCDS
This section provides some necessary information about the IOCDS and how to customize some settings for sharing network cards or DASDs among several LPARs. In
the IOCDS, the chpid and types of the devices connected to the IBM System z are
defined. The resources can be dedicated or shared among LPARs.
WARNING: Sharing Devices (DASD)
Do not share writable DASD among LPARs because this might result in data loss. Consider the definition of the necessary resources in advance when
planning the setup for SUSE Linux Enterprise Server on IBM System z.
This example shows how to dedicate a DASD to one specific LPAR. This LPAR is
referred to as LPAR1.
Example 4.1: Dedicating DASD to One LPAR
CHPID PATH=FD,TYPE=DSD,SHARED
CNTLUNIT CUNUMBR=FD00,PATH=FD,UNITADD=((00,256)),UNIT=3990-2
IODEVICE ADDRESS=(FD03,1),CUNUMBR=FD00,UNIT=3390,PART=LPAR1
Installation on IBM System z
45
To share a DASD among LPARs, delete the PART=LPAR1 part in the IOCDS definition. This might be useful for high availability reasons or for sharing data among
LPARs read-only.
Several Linux systems can use the same network device if you share it among LPARs
or z/VM guests. This reduces the number of network devices that must be provided to
the Linux system. On the other hand, you might provide more than one network device to one Linux system to make it more available in case one connection fails.
Network cards like OSA-Express can be used in two different modes. These modes
are known as QDIO and non-QDIO mode. Define these modes in the IOCDS by using
the TYPE statement. QDIO mode is much faster than non-QDIO mode, but uses three
device addresses instead of two in non-QDIO. Consider the limited number of device
addresses when planning the setup of your IBM System z Linux environment.
Example 4.2: Sharing OSA Express Card among LPARs (non-qdio) on z9
CHPID PATH=(FE),SHARED,PARTITION=((LPAR1,LPAR2)),TYPE=OSE
CNTLUNIT CUNUMBR=FE00,PATH=(FE),UNIT=OSA
IODEVICE ADDRESS=(FE00,016),CUNUMBR=(FE00),UNIT=OSA
IODEVICE ADDRESS=(FEFE,001),CUNUMBR=(FE00),UNIT=OSAD
Example 4.3: Sharing OSA Express Card among LPARs (qdio) on z9
CHPID PATH=(FE),SHARED,PARTITION=((LPAR1,LPAR2)),TYPE=OSD
CNTLUNIT CUNUMBER=FE00,PATH=(FE),UNIT=OSA
IODEVICE ADDRESS=(FE00,016),CUNUMBR=(FE00),UNIT=OSA
IODEVICE ADDRESS=(FEFE,001),CUNUMBR=(FE00),UNIT=OSAD
4.2 Preparing for Installation
In this section, learn how to make the data accessible for installation, install SUSE
Linux Enterprise Server using different methods, and prepare and use the IPL of the
SUSE Linux Enterprise Server installation system. Also find out about network configuration and network installation.
4.2.1 Making the Installation Data
Available
This section provides detailed information about making the SUSE Linux Enterprise
Server IBM System z installation data accessible for installation. Depending on your
46
Deployment Guide
computer and system environment, choose between NFS or FTP installation. If you
are running Microsoft Windows workstations in your environment, you can also use
the Windows network (including the SMB protocol) to install SUSE Linux Enterprise
Server on your IBM System z system.
TIP: IPL from DVD
Since Service Pack 1 of SUSE Linux Enterprise Server Version 10, it is possible to IPL from DVD and use the DVD as the installation medium. This is
very convenient if you have restrictions setting up an installation server providing installation media over your network. The prerequisite is an FCP-attached SCSI DVD Drive.
NOTE: No Installation “From Hard Disk”
It is not possible to install from hard disk by putting the content of the DVD to
a partition on a DASD.
4.2.1.1 Using a Linux Workstation or SUSE Linux
Enterprise Server DVD
If you have a Linux workstation running in your computer environment, use the workstation to provide the installation data to the IBM System z installation process by
NFS or FTP. If the Linux workstation runs under SUSE Linux Enterprise Server,
you can set up an installation server (NFS or FTP) using the YaST Installation Server module as described in Section 14.2.1, “Setting Up an Installation Server Using
YaST” (page 254).
Over NFS
Use NFS (network file system) to make the installation media available.
IMPORTANT: Exporting Mounted Devices with NFS
Exporting the file system root (/) does not imply the export of mounted devices, such as DVD. Explicitly name the mount point in /etc/exports:
/media/dvd
*(ro)
After changing this file, restart the NFS server with the command rcnfsserver restart.
Installation on IBM System z
47
Over FTP
Setting up an FTP server on a Linux system involves the installation of the server software itself, such as wuftpd or proftpd, as well as other possible configuration tasks.
Using YaST, the installation step is straightforward: select the package to install and
start the installation. Skip the configuration of the FTP server if no anonymous FTP
should be used for the installation. Instead, use an FTP login with a valid username
and password. You might want to create a user account for this task only. The FTP
daemon does not need to be started by hand. It can be started by inetd if an FTP connection is requested. To activate the new settings, enter rcinetd restart or
rcxinetd restart.
SUSE Linux Enterprise Server on DVD
DVD1 of the SUSE Linux Enterprise Server for IBM System z contains a bootable
Linux image for Intel-based workstations as well as an image for System z.
For Intel-based workstations, boot from this DVD, answer the questions regarding
your language and keyboard layout, and select Start rescue system. You need at least
64 MB RAM for this. No disk space is needed because the entire rescue system resides in the workstation's RAM. This approach takes some Linux and networking experience, because you need to set up the networking of the workstation manually.
For System z, IPL your LPAR/VM guest from this DVD as described in Section “IPL
from FCP-Attached SCSI DVD” (page 56). After entering your network parameters, the installation system treats the DVD as the source of installation data. Because System z cannot have an X11-capable terminal attached directly, choose between VNC or SSH installation. SSH also provides a graphical installation by tunneling the X connection through SSH with ssh -X.
4.2.1.2 Using a Microsoft Windows Workstation
If there is a Microsoft Windows workstation available in your network, use this computer to make the installation media available. The easiest way to do this is to use the
SMB protocol, already included in the Windows operating system. Be sure to activate SMB over TCP/IP as this enables the encapsulation of SMB packages into TCP/
IP packages. Find details in the Windows online help or other Windows-related documentation that covers networking. Another option is to use FTP. This also requires
some third-party software for Windows.
48
Deployment Guide
With SMB
To make the installation media available with SMB, just insert the SUSE Linux Enterprise Server DVD 1 into the DVD drive of the Windows workstation. Then create
a new share using the DVD-ROM drive's letter and make it available for everyone in
the network.
The installation path in YaST can be:
smb://DOMAIN;USER:[email protected]/SHAREPATH
Where the placeholders mean:
DOMAIN
Optional workgroup or active directory domain.
USER , PW
Optional username and password of a user who can access this server and its
share.
SERVERNAME
The name of the server that hosts the share(s).
SHAREPATH
The path to the share(s).
With NFS
Refer to the documentation provided with the third party product that enables NFS
server services for your Windows workstation. The DVD-ROM drive containing the
SUSE Linux Enterprise Server DVDs must be in the available NFS path.
With FTP
Refer to the documentation provided with the third party product that is enabling FTP
server services on your Windows workstation. The DVD-ROM drive containing the
SUSE Linux Enterprise Server DVDs must be in the available FTP path.
The FTP server that is bundled with some Microsoft Windows releases implements
only a subset of the FTP command set and is not suitable for providing the installation
data. However, other products (such as the FTP server that is part of Hummingbird
Exceed or WAR-FTPD) have been reported as functional.
Installation on IBM System z
49
Using an FCP-Attached SCSI DVD Drive
After you IPLed from the SCSI DVD as described in Section 4.1.3.4, “Load from
SCSI-Attached DVD” (page 45), the installation system uses the DVD as the installation medium. In that case, you do not need the installation media on an FTP,
NFS, or SMB server. However, you need the network configuration data for your
SUSE Linux Enterprise Server, because you must set up the network during the installation to perform a graphical installation by VNC or by X tunneled through SSH.
4.2.1.3 Using a Cobbler Server for zPXE
IPLing from the network requires a Cobbler server, to provide the kernel, initrd, and
the installation data. Preparing the Cobbler server requires four steps:
• Importing the Installation Data
• Adding a Distribution
• Adding Profiles
• Adding Systems
Importing the Installation Data
Importing the media requires the installation source to be available on the Cobbler
server—either from DVD or from a network source. Run the following command to
import the data:
cobbler import --path=PATH
--name=IDENTIFIER
--arch=s390x
Mount point of the installation data.
A string identifying the imported product, for example “sles11_sp3_s390x”.
This string is used as the name for the subdirectory where the installation data
is copied to. On a Cobbler server running on SUSE Linux Enterprise this is /
srv/www/cobbler/ks_mirror/IDENTIFIER. This path may be different if Cobbler runs on another operating system.
Adding a Distribution
By adding a distribution, you tell Cobbler to provide the kernel and the initrd required
to IPL via zPXE. Run the following command on the Cobbler server to add SUSE
Linux Enterprise Server for IBM System z:
50
Deployment Guide
cobbler distro add --arch=s390x --breed=suse --name="IDENTIFIER" \
--os-version=sles10 \
--initrd=/srv/www/cobbler/ks_mirror/IDENTIFIER/boot/s390x/initrd \
--kernel=/srv/www/cobbler/ks_mirror/IDENTIFIER/boot/s390x/vmrdr.ikr
--kopts="install=http://cobbler.example.com/cobbler/
ks_mirror/IDENTIFIER"
\
Custom identifier for the distribution, for example “SLES 11 SP4 System z”.
Must be unique.
Operating system identifier. Use sles10.
Path to the initrd. The first part of the path (/srv/www/cob​
bler/ks_mirror/IDENTIFIER/) depends on the location where Cobbler
imported the data and the subdirectory name you chose when importing the installation data.
Path to the kernel. The first part of the path (/srv/www/cob​
bler/ks_mirror/IDENTIFIER/) depends on the location where Cobbler
imported the data and the subdirectory name you chose when importing the installation data.
URl to the installation directory on the Cobbler server.
4.2.1.4 Adding Profiles
With a profile you can add additional options to a distribution—for example adding
an AutoYaST file for an automated installation. You can specify multiple profiles per
distribution; at least one must be created.
cobbler profile add
--name=PROFILENAME --distro=DISTRIBUTION
kickstart=PATH_TO_AUTOYAST_FILE
--
Unique name for the profile.
Distribution to which the profile should apply. You must use the string specified
with --name=IDENTIFIER in the importing step here.
Specify the path to an AutoYaST file for an automated installation here. This
parameter is optional.
4.2.1.5 Adding Systems
The last step that is required is to add systems to the Cobbler server. A system addition needs to be done for every System z guest that should boot via zPXE. Guests are
identified via their z/VM user ID (in the following example, an ID called “LINUX01”
is assumed). To add a system, run the following command:
Installation on IBM System z
51
cobbler system add --name=LINUX01 --hostname=linux01.example.com \
--ip=192.168.2.103 --subnet=192.168.2.255 --netmask=255.255.255.0 \
--name-servers=192.168.1.116 --name-servers-search=example.com \
--gateway=192.168.2.1 --kopts="KERNEL_OPTIONS"
With the --kopts option you can specify the kernel and installation parameters you
would normally specify in the parmfile. The parameters are entered as a space-separated list in the form of PARAMETER1=VALUE1 PARAMETER2=VALUE2. The installer will prompt you for missing parameters. For a completely automated installation you need to specify all parameters for networking, DASDs and provide an AutoYaST file. The following shows an example for a guest equipped with an OSA interface using the same network parameters as above.
--kopts=" \
AutoYaST=http://192.168.0.5/autoinst.xml \
Hostname=linux01.example.com \
Domain=example.com \
HostIP=192.168.2.103 \
Gateway=192.168.2.1 \
Nameserver=192.168.1.116 \
Searchdns=example.com \
InstNetDev=osa; \
Netmask=255.255.255.0 \
Broadcast=192.168.2.255 \
OsaInterface=qdio \
OsaMedium=eth \
Layer2=0 \
PortNo=0 \
ReadChannel=0.0.0600 \
WriteChannel=0.0601 \
DataChannel=0.0.0602 \
Portname=DT70 \
DASD=600"
4.2.2 Installation Types
This section provides information about which steps must be performed to install
SUSE Linux Enterprise Server for each of the installation modes and where to find
the appropriate information. After the preparations mentioned in the previous chapters have been accomplished, follow the installation overview of the desired installation mode to install SUSE Linux Enterprise Server on your system.
As described in Section 4.2.1, “Making the Installation Data Available” (page 46),
there are two different installation modes for Linux on IBM System z:
• LPAR Installation
52
Deployment Guide
• z/VM Installation
Procedure 4.1: Overview of LPAR Installation
1 Prepare the devices needed for installation. See Section 4.2.3.1, “LPAR
Installation” (page 54).
2 IPL the installation system. See Section 4.2.4.1, “LPAR Installation” (page 56).
3 Configure the network. See Section 4.2.5, “Network Configuration” (page 61).
4 Connect to the SUSE Linux Enterprise Server installation system. See Section 4.2.6, “Connecting to the SUSE Linux Enterprise Server Installation
System” (page 64).
5 Start the installation using YaST and IPL the installed system. See Chapter 6, Installation with YaST (page 93).
Procedure 4.2: Installation Overview of z/VM Installation
1 Prepare the devices needed for installation. See Section 4.2.3.2, “z/VM
Installation” (page 54).
2 IPL the installation system. See Section 4.2.4.2, “z/VM Installation” (page 58).
3 Configure the network. See Section 4.2.5.1, “z/VM Installation” (page 62).
4 Connect to the SUSE Linux Enterprise Server installation system. See Section 4.2.6, “Connecting to the SUSE Linux Enterprise Server Installation
System” (page 64).
5 Start the installation using YaST and IPL the installed system. See Chapter 6, Installation with YaST (page 93).
4.2.3 Preparing the IPL of the SUSE Linux
Enterprise Server Installation System
Installation on IBM System z
53
4.2.3.1 LPAR Installation
Configure your IBM System z system to start in ESA/S390 or LINUX-only mode
with an appropriate activation profile and IOCDS. Consult IBM documentation for
more on how to achieve this.
IOCDS: Attaching and Configuring Devices
A SUSE Linux Enterprise Server installation needs at least two devices: a DASD and
a network connection device. For an IPL from tape, a tape device should also be accessible. Devices are configured and attached to an LPAR in the IOCDS (input output configuration data set). This example defines one DASD, one OSA-2 network device, and a tape device for LPAR Z1. For further information about how to set up the
IOCDS for Linux, refer to your machine's IBM hardware documentation.
Example 4.4: An Example IOCDS
CHPID PATH=(CSS(0),FD),PCHID=120,TYPE=FC
CHPID PATH=(CSS(0),FE),PCHID=320,TYPE=OSD
CHPID PATH=(CSS(0),10),PCHID=3A0,TYPE=CNC
CNTLUNIT CUNUMBR=FD00,PATH=((CSS(0),FD)),UNITADD=((00,1)),UNIT=2105
IODEVICE ADDRESS=(FD00,1),CUNUMBR=(FD00),UNIT=3390B,UNITADD=00
CNTLUNIT CUNUMBR=FE20,PATH=((CSS(0),FE)),UNIT=OSA
IODEVICE ADDRESS=(FE20,1),CUNUMBR=(FE20),UNIT=OSA
IODEVICE ADDRESS=(FEFE,1),CUNUMBR=(FE20),UNIT=OSAD
CNTLUNIT CUNUMBR=100A,PATH=((CSS(0),10)),UNIT=3480,UNITADD=((0A,1))
IODEVICE ADDRESS=(100A,1),CUNUMBR=(100A),UNIT=3480,UNITADD=00
Proceed with Section 4.2.4.1, “LPAR Installation” (page 56).
4.2.3.2 z/VM Installation
Adding a Linux Guest
The first step is to attach and format one or multiple DASDs in the system to be used
by the Linux guest in z/VM. Next, create a new user in z/VM. The example shows
the directory for a user LINUX1 with the password LINPWD, 256 MB of memory
(extendable up to 1024 MB), 32 MB of expanded RAM (XSTORE), some minidisks
(MDISK), two CPUs and an OSA QDIO device.
54
Deployment Guide
TIP: Assigning Memory to z/VM guests
When assigning memory to a z/VM guest, make sure that the memory size
suits the needs of your preferred installation type. See Section “Memory
Requirements” (page 40). To set the memory size to 512 MB, use the
command CP DEFINE STORAGE 512M. After the installation has finished,
reset the memory size to the desired value.
Example 4.5: Configuration of a z/VM Directory
USER LINUX1 LINPWD 256M 1024M G
*____________________________________________
* LINUX1
*____________________________________________
* This VM Linux guest has two CPUs defined.
CPU 01 CPUID 111111
CPU 02 CPUID 111222
IPL CMS PARM AUTOCR
IUCV ANY
IUCV ALLOW
MACH ESA 10
OPTION MAINTCCW RMCHINFO
SHARE RELATIVE 2000
XSTORE 32M
CONSOLE 01C0 3270 A
SPOOL 000C 2540 READER *
SPOOL 000D 2540 PUNCH A
SPOOL 000E 3203 A
* OSA QDIO DEVICE DEFINITIONS
DEDICATE 9A0 9A0
DEDICATE 9A1 9A1
DEDICATE 9A2 9A2
*
LINK MAINT 0190 0190 RR
LINK MAINT 019E 019E RR
LINK MAINT 019D 019D RR
* MINIDISK DEFINITIONS
MDISK 201 3390 0001 0050 DASD40 MR ONE4ME TWO4ME THR4ME
MDISK 150 3390 0052 0200 DASD40 MR ONE4ME TWO4ME THR4ME
MDISK 151 3390 0253 2800 DASD40 MR ONE4ME TWO4ME THR4ME
This example uses minidisk 201 as the guest's home disk. Minidisk 150 with 200
cylinders is the Linux swap device. Disk 151 with 2800 cylinders holds the Linux installation.
Now add (as the user MAINT) the guest to the user directory with DIRM FOR
LINUX1 ADD. Enter the name of the guest (LINUX1) and press F5. Set up the environment of the user with:
Installation on IBM System z
55
DIRM DIRECT
DIRM USER WITHPASS
The last command returns a reader file number. This number is needed for the next
command:
RECEIVE <number> USER DIRECT A (REPL)
Assign the directories to the guest with DISKMAP USER DIRECT A. You can now
log in on the guest as user LINUX1.
If you do not have the dirmaint option available, refer to the IBM documentation
to set up this user.
Proceed with Section 4.2.4.2, “z/VM Installation” (page 58).
4.2.4 IPLing the SUSE Linux Enterprise
Server Installation System
4.2.4.1 LPAR Installation
There are different ways to IPL SUSE Linux Enterprise Server into an LPAR. The
preferred way is to use the Load from CD-ROM or server feature of the SE or HMC.
IPL from DVD-ROM
Mark the LPAR to install and select Load from CD-ROM or server. Leave the field
for the file location blank or enter the path to the root directory of the first DVDROM and select continue. In the list of options that appears, choose the default selection. Operating system messages should now show the kernel boot messages.
IPL from FCP-Attached SCSI DVD
You can use the Load procedure by selecting SCSI as Load type to IPL from SCSI.
Enter the WWPN (Worldwide port name) and LUN Logical unit number) provided
by your SCSI bridge or storage (16 digits—do not omit the trailing 0s). The boot program selector must be 2. Use your FCP adapter as Load address and perform an IPL.
56
Deployment Guide
IPL from ESCON or FICON Attached Tape
If you cannot IPL from DVD, create a channel attached tape from which to IPL the
SUSE Linux Enterprise Server installation image. Use the LOAD button in the SE or
HMC with the tape device address as the load address to IPL the SUSE Linux Enterprise Server installation system.
There are many ways to create an IPLable tape. One is to copy the files:
/boot/s390x/tapeipl.ikr
/boot/s390x/parmfile
/boot/s390x/initrd
as binary files from DVD 1 (for example, using FTP from a Linux workstation).
Name them
SLES11 IMAGE
SLES11 PARM
SLES11 INITRD
and write them onto a tape with the REXX from the example.
IMPORTANT: Transferring Binaries using FTP
Do not upload the files as fixed 80. Store them as fixed 1024. Use the
FTP command locsite fix 1024.
Example 4.6: REXX Script to Create an IPLable Tape
'REWIND 181'
'FILEDEF IN1 DISK' SLES11 IMAGE A
'FILEDEF IN2 DISK' SLES11 PARM A
'FILEDEF IN3 DISK' SLES11 INITRD A
'FILEDEF OUT TAP1 (RECFM F BLOCK 1024 LRECL 1024 PERM'
say 'Writing: ' left(file1,23)
'MOVEFILE IN1 OUT'
say 'Writing: ' left(file2,23)
'MOVEFILE IN2 OUT'
say 'Writing: ' left(file3,23)
'MOVEFILE IN3 OUT'
say 'Done.'
'REWIND 181'
exit
The tape in this script is attached as 181. Adjust the script to your needs.
Installation on IBM System z
57
4.2.4.2 z/VM Installation
This section is about IPLing the installation system to install SUSE Linux Enterprise
Server for IBM System z on a z/VM system.
IPL from the z/VM Reader
You need a working TCP/IP connection and an FTP client program within your newly defined z/VM guest to transfer the installation system via FTP. Setting up TCP/IP
for z/VM is beyond the scope of this manual. Refer to the appropriate IBM documentation.
Log in as the z/VM Linux guest to IPL. Make the content of the directory /boot/
s390x on DVD 1 of the SUSE Linux Enterprise Server for IBM System z available
by FTP within your network. From this directory, get the files vmrdr.ikr, ini​
trd, parmfile, and sles11.exec. Transfer the files with a fixed block size of
80 characters. Specify it with the FTP command locsite fix 80. It is important
to copy vmrdr.ikr (the Linux kernel) and initrd (the installation image) as binary files, so use the binary transfer mode. parmfile and sles11.exec need
to be transferred in ASCII mode.
The example shows the steps necessary. In this example, the required files are accessible from an FTP server at the IP address 192.168.0.3 and the login is lininst.
It may differ for your network.
Example 4.7: Transferring the Binaries via FTP
FTP 192.168.0.3
VM TCP/IP FTP Level 530
Connecting to 192.168.0.3, port 21
220 ftpserver FTP server (Version wu-2.4.2-academ[BETA-18](1)
Thu Feb 11 16:09:02 GMT 2010) ready.
USER
lininst
331 Password required for lininst
PASS
******
230 User lininst logged in.
Command:
binary
200 Type set to I
Command:
locsite fix 80
Command:
get /media/dvd1/boot/s390x/vmrdr.ikr sles11.image
58
Deployment Guide
200 PORT Command successful
150 Opening BINARY mode data connection for /media/dvd1/boot/s390x/vmrdr.ikr
(6757376 bytes)
226 Transfer complete.
6757376 bytes transferred in 8.826 seconds.
Transfer rate 766.70 Kbytes/sec.
Command:
get /media/dvd1/boot/s390x/initrd sles11.initrd
200 PORT Command successful
150 Opening BINARY mode data connection for /media/dvd1/boot/s390x/initrd
(12654815 bytes)
226 Transfer complete.
12194534 bytes transferred in 16.520 seconds.
Transfer rate 766.70 Kbytes/sec.
Command:
ascii
200 Type set to A
Command:
get /media/dvd1/boot/s390x/parmfile sles11.parmfile
150 Opening ASCII mode data connection for /media/dvd1/boot/s390x/parmfile
(71 bytes)
226 Transfer complete.
71 bytes transferred in 0.092 seconds.
Transfer rate 0.71 Kbytes/sec.
Command:
get /media/dvd1/boot/s390x/sles11.exec sles11.exec
150 Opening ASCII mode data connection for /media/dvd1/boot/s390x/
sles11.exec
(891 bytes)
226 Transfer complete.
891 bytes transferred in 0.097 seconds.
Transfer rate 0.89 Kbytes/sec.
Command:
quit
Use the REXX script sles11.exec you just downloaded to IPL the Linux installation
system. This script loads the kernel, parmfile, and the initial RAM disk into the reader
for IPL.
Example 4.8: SLES11 EXEC
/* REXX LOAD EXEC FOR SUSE LINUX S/390 VM GUESTS
/* LOADS SUSE LINUX S/390 FILES INTO READER
SAY ''
SAY 'LOADING SLES11 FILES INTO READER...'
'CP CLOSE RDR'
'PURGE RDR ALL'
'SPOOL PUNCH * RDR'
'PUNCH SLES11 IMAGE A (NOH'
'PUNCH SLES11 PARMFILE A (NOH'
'PUNCH SLES11 INITRD A (NOH'
'I 00C'
*/
*/
Installation on IBM System z
59
With this script you can IPL the SUSE Linux Enterprise Server installation system
with the command sles11. The Linux kernel then starts and prints its boot messages.
To continue the installation, proceed to Section 4.2.5.1, “z/VM
Installation” (page 62).
IPL from FCP-Attached SCSI DVD
To IPL in z/VM, prepare the SCSI IPL process by using the SET LOADDEV parameter:
SET LOADDEV PORTNAME 200400E8 00D74E00 LUN 00020000 00000000 BOOT 2
After setting the LOADDEV parameter with the appropriate values, IPL your FCP
adapter, for example:
IPL FC00
To continue the installation, proceed with Section 4.2.5.1, “z/VM
Installation” (page 62).
IPL from ESCON or FICON Attached tape
If you cannot IPL from a z/VM reader, create a channel attached tape from which to
IPL the SUSE Linux Enterprise Server installation image. For instructions, refer to
Section “IPL from ESCON or FICON Attached Tape” (page 57).
To continue the installation, proceed with Section 4.2.5.1, “z/VM
Installation” (page 62).
IPL from a Cobbler Server with zPXE
To IPL from a Cobbler server with zPXE you need to transfer the zpxe.exec script
via FTP from the Cobbler server to your z/VM guest. The z/VM guest needs a working TCP/IP connection and an FTP client program.
Log in as the z/VM Linux guest to IPL and transfer the script with
a fixed size of 80 characters in ASCII mode (see Example 4.7,
“Transferring the Binaries via FTP” (page 58) for an example). The zpxe.exec script is available on the Cobbler server at
ftp://IP_OF_COBBLER_SERVER/zSERIES_INSTALLATION_DIRECTORY/
boot/s390x/zpxe.exec. The exact location of
60
Deployment Guide
zSERIES_INSTALLATION_DIRECTORY depends on where you imported
the installation data on the Cobbler server (see Section “Importing the Installation
Data” (page 50) for details).
zpxe.exec is supposed to replace the PROFILE EXEC of your guest. Make
a backup copy of the existing PROFILE EXEC and rename ZPXE EXEC to
PROFILE EXEC. Alternatively call ZPXE EXEC from the existing PROFILE EX​
EC by using a new line with the following content: 'ZPXE EXEC'.
The last step is to create a config file, ZPXE CONF, telling ZPXE EXEC which Cobbler server to contact and which disk to IPL. Run xedit zpxe conf a and create
ZPXE CONF with the following content (replace the example data accordingly):
HOST cobbler.example.com
IPLDISK 600
On the next log in to your z/VM guest, the Cobbler server will be connected. If an installation is scheduled on the Cobbler server, it will be executed. To schedule the installation, run the following command on the Cobbler server:
cobbler system edit --name ID
--netboot-enabled 1
--profile PROFILENAME
z/VM user ID.
Enable IPLing from the network.
Name of an existing profile, see Section 4.2.1.4, “Adding
Profiles” (page 51).
4.2.5 Network Configuration
Wait until the kernel has completed its start-up routines. If you are installing in basic
mode or in an LPAR, open the Operating System Messages on the HMC or SE.
First, choose Start Installation or System in the linuxrc main menu then Start Installation or Update to start the installation process. Select Network as your installation
medium then select the type of network protocol you will be utilizing for the installation. Section 4.2.1, “Making the Installation Data Available” (page 46) describes
how to make the installation data available for the various types of network connections. Currently, FTP, HTTP, NFS, and SMB/CIFS (Windows file sharing) are supported.
Now set up the network device over which to receive the installation data: OSA-2 or
OSA Express or HiperSockets. The following network adapters are still available and
Installation on IBM System z
61
usable, but no longer supported: CTC, ESCON, IUCV. Next, choose the CCW bus
interface and the physical medium (Ethernet). As a result, the respective driver is installed and you see the corresponding kernel messages.
Proceeding with the installation, linuxrc displays a list of potential usable read, write,
and, if applicable, data channels. After entering the addresses for each channel, you
may also need to enter additional information, such as the port name for OSA ethernet cards.
Next, decide whether to use DHCP autoconfiguration for setting up the network interface parameters. Because DHCP only works on a few devices and requires special
hardware configuration settings, you probably want to say NO here. When you do so,
you are prompted for the networking parameters of your installation network device:
• The IP address of the system to install
• The corresponding netmask
• The IP address of a gateway to reach the server
• The IP address of your domain name server (DNS)
When using an OSA Express Network Card you are now prompted for a relative port
number. This was added to support the new 2 port OSA Express 3 Network devices.
If you are not using an OSA Express 3 device, please enter 0. OSA Express cards also
have the option of running in an “OSI layer 2 support” mode or using the older more
common “layer 3” mode. The card mode affects all systems that share the device including systems on other LPARs. If in doubt, please specify 2 for compatibility with
the default mode used by other operating systems such as z/VM and z/OS. Consult
with your hardware administrator for further information on these options.
4.2.5.1 z/VM Installation
After the kernel has completed its start-up routines, answer a few questions regarding
the network setup. First, select the type of network connection to use: OSA Express or
HiperSockets. In this example installation, OSA Express is used.
The system now displays a possible OSA configuration. Choose first whether to use
QDIO or LCS OSA. Next, choose the physical medium to use and enter the device
addresses. If you prefer another setup, enter the device address of the OSA read channel (0.0.0700 in this example) then the one of the OSA write channel (0.0.0701) and
62
Deployment Guide
the OSA control channel (0.0.0702). After entering the channels, insert the name of
the port to which the OSA card is connected.
SUSE Linux Enterprise Server now tries to load the network module by building a parameter line with the information provided and displaying all loaded modules. Loading was successful if you get an output like:
Example 4.9: Network Device Driver Parameters
(portname YSW2)
(Port 0)
qdio: 0.0.0702 OSA on SC 3 using AI:1 QEBSM:0 PCI:1 TDD:1 SIGA:RW AO
qeth.736dae: 0.0.0700: Device is a Guest LAN QDIO card (level: V540)
with link type GuestLAN QDIO (portname: YSW2)
qeth.47953b: 0.0.0700: Hardware IP fragmentation not supported on eth0
qeth.066069: 0.0.0700: Inbound source MAC-address not supported on eth0
qeth.d7fdb4: 0.0.0700: VLAN enabled
qeth.e90c78: 0.0.0700: Multicast enabled
qeth.5a9d02: 0.0.0700: IPV6 enabled
qeth.184d8a: 0.0.0700: Broadcast enabled
qeth.dac2aa: 0.0.0700: Using SW checksumming on eth0.
qeth.9c4c89: 0.0.0700: Outbound TSO not supported on eth0
Next, enter your IP address, netmask, and default gateway. To install over iucv or ctc,
enter additional information, like the the peer address (for a point-to-point adapter) or
the port name.
Finally, the IP address of the DNS server and the MTU size are requested. The MTU
size should always match the one used by the network to which you are connecting.
Now a summary is displayed. Confirm if your input is correct. Before the network is
started, enter a password that is valid only during the installation. After having IPLed
the installed system, enter the real root password.
With all basic parameters set up, the network is started. Check the output of ifconfig, which should contain two entries: a loopback (lo) connection and one connection
(eth0, ctc0, escon0, iucv0, or hsi0) with correct settings.
Example 4.10: Example ifconfig
/sbin/ifconfig eth0 :
Link encap:Ethernet HWaddr 02:00:01:00:00:27
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::200:100:100:27/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1492 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Installation on IBM System z
63
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 Mb) TX bytes:0 (0.0 Mb)
4.2.6 Connecting to the SUSE Linux
Enterprise Server Installation System
After setting up your network connection, linuxrc prompts for the details of the installation source chosen earlier in the process, for example, the server IP address and the
directory in which the data is located.
Finally, linuxrc wants to know what type of display you want to use to control the installation procedure. Possible choices are X11 (X Window System), VNC (Virtual
Network Computing protocol), SSH (text mode or X11 installation via Secure Shell),
or ASCII Console.
When choosing the latter (ASCII Console), YaST will be started in text mode and
you can perform the installation directly within your terminal. See Chapter 3, YaST in
Text Mode (↑Administration Guide) for usage instructions.
NOTE: Terminal Emulation for ASCII Console
In order to be able to work with YaST in text mode, it needs to run in a terminal with VT220/Linux emulation (also referred to as ASCII console). You
will not be able to use YaST in a 3270 terminal, for example.
4.2.6.1 Initiating the Installation for VNC
1 After the installation option VNC has been chosen, the VNC server starts. A short
note displayed in the console provides information about which IP address and display number is needed for a connection with vncviewer. Alternatively, a URL is
given here for entry into your Java-enabled browser to connect to the installation
system.
2 Start a VNC client application on your client system. Either use vncviewer or the
VNC Java client and a Java-enabled Web browser.
3 Enter the IP address and the display number of the SUSE Linux Enterprise Server
installation system when prompted to do so.
64
Deployment Guide
If you connect via a Java-enabled browser, enter a URL containing the IP address
of the installation system and the appropriate port number in the format:
http://<IP address of installation system>:5801/
4 After the connection has been established, start installing SUSE Linux Enterprise
Server with YaST.
4.2.6.2 Initiating the Installation for the X Window
System
IMPORTANT: X Authentication Mechanism
The direct installation with the X Window System relies on a primitive authentication mechanism based on hostnames. This mechanism is disabled on
current SUSE Linux Enterprise Server versions. Installation with SSH or VNC
is preferred.
1 Make sure that the X server allows the client (the system that is installed) to connect. Set the variable
DISPLAYMANAGER_XSERVER_TCP_PORT_6000_OPEN="yes" in the file
/etc/sysconfig/displaymanager. Then restart the X server and allow
client binding to the server using xhost <client IP address>.
2 When prompted at the installation system, enter the IP address of the machine running the X server.
3 Wait until YaST opens then start the installation.
4.2.6.3 Initiating the Installation for SSH
To connect to an installation system with the name earth using SSH, execute
ssh -X earth. If your workstation runs on Microsoft Windows, use the ssh
and telnet client and terminal emulator putty, which is available from http://
www.chiark.greenend.org.uk/~sgtatham/putty/. Set Enable X11 forwarding in putty under Connection > SSH > X11.
A login prompt appears. Enter root and log in with your password. Enter yast2 to
start YaST.
Installation on IBM System z
65
Proceed with the detailed description of the installation procedure that can be found
in Chapter 6, Installation with YaST (page 93).
4.3 Network Connection Types
SUSE Linux Enterprise Server for IBM System z includes network drivers for OSA
devices (ethernet, and gigabit ethernet) and HiperSockets. This chapter describes the
configuration within the SUSE Linux Enterprise Server installation system.
WARNING: CTC, ESCON, and IUCV Interfaces No Longer Supported
CTC, ESCON, and IUCV interfaces are no longer officially supported. For
compatibility reasons, they are still usable, but with the next release of SUSE
Linux Enterprise Server the support of these interfaces will be dropped completely.
4.3.1 HiperSockets
Select your device from the list of network devices. Then enter the network device
read channel number (such as 0.0.700), the write channel number (like 0.0.701) and
the data channel number (like 0.0.702).
Example 4.11: Supported Network Connection Types and Driver Parameters
Choose the network device.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
IBM
parallel CTC Adapter (0.0.0600)
parallel CTC Adapter (0.0.0602)
parallel CTC Adapter (0.0.0604)
Hipersocket (0.0.0700)
Hipersocket (0.0.0701)
Hipersocket (0.0.0702)
OSA Express Network card (0.0.050c)
OSA Express Network card (0.0.050d)
OSA Express Network card (0.0.050e)
OSA Express Network card (0.0.f401)
OSA Express Network card (0.0.f400)
OSA Express Network card (0.0.f402)
IUCV
> 4
Device address for read channel [0.0.700]
[0.0.700]> 0.0.700
66
Deployment Guide
Device address for write channel
> 0.0.701
Device address for data channel
> 0.0.702
Next, choose manual configuration then enter the IP address, netmask, broadcast address, IP address of the gateway, and the searchlist of the DNS server.
Example 4.12: Network Device Name
Automatic configuration via DHCP?
1) Yes
2) No
> 2
Enter your IP address
> 192.168.0.20
Enter your netmask. For a normal class C network, this is usually
255.255.255.0 [255.255.255.0]
> 255.255.255.0
Enter the IP address of the gateway. Leave empty if you don't need one
> 192.168.0.1
Enter your search domains, separated by a space:
> example.com
4.3.2 Gigabit Ethernet with the qeth
Module
Select an IBM OSA Express Network card from the list of network devices,
and then 1 for ethernet. When prompted, enter the network device's read, write, and
data channel numbers (for example, 0.0.0600, 0.0.0601, and 0.0.0602) and
the port name, if applicable. Choose whether to enable OSI Layer 2 support.
Example 4.13: Network Device Driver Parameters
Detecting and loading network drivers
netiucv.8db02b: driver initialized
Choose the network device.
1) IBM OSA Express Network card (0.0.09a0)
2) IBM OSA Express Network card (0.0.09a1)
Installation on IBM System z
67
3)
4)
5)
6)
7)
IBM
IBM
IBM
IBM
IBM
OSA Express
OSA Express
OSA Express
OSA Express
IUCV
Network
Network
Network
Network
card
card
card
card
(0.0.09a2)
(0.0.0600)
(0.0.0601)
(0.0.0602)
> 4
Please choose the physical medium.
1) Ethernet
2) Token Ring
> 1
Enter the relative port number
> 0
Device address for read channel
[0.0.0600]> 0.0.0600
Device address for write channel
> 0.0.0601
Device address for data channel
> 0.0.0602
Portname to use
> DT70
Enable OSI Layer 2 support?
1) Yes
2) No
> 2
Next, deny the DHCP configuration and enter the IP address and netmask. Now enter
the IP address of the gateway (if applicable), the search domain(s) and the IP address
of the DNS server.
Example 4.14: Network configuration
Automatic configuration via DHCP?
1) Yes
2) No
> 2
Enter your IPv4 address.
Example: 192.168.5.77/24
> 192.168.0.20
68
Deployment Guide
Enter your netmask. For a normal class C network, this is usually
255.255.255.0
[255.255.255.0]> 255.255.255.0
Enter the IP address of the gateway. Leave empty if you don't need one
> 192.168.0.2
Enter your search domains, separated by a space:
> example.net
Enter the IP address of your name server. Leave empty or enter "+++" if you
don't need one
> 192.168.0.1
4.4 The parmfile—Automating the
System Configuration
The installation process can be partly automated by specifying the crucial parameters
in the parmfile. The parmfile contains all the data required for network setup and DASD configuration. In addition to that, it can be used to set up the connection method to the SUSE Linux Enterprise Server installation system and the YaST instance running there. User interaction is thus limited to the actual YaST installation
controlled by YaST dialogs.
The following parameters can be passed to the installation routine, which takes them
as default values for installation. All IP addresses, server names, and numerical values
are just examples. Replace these values with the ones needed in your installation scenario.
The number of lines in the parmfile is limited to 10. Specify more than one parameter
on a line. Parameter names are not case-sensitive. Separate the parameters by spaces.
You may specify the parameters in any order. Always keep the PARAMETER=value
string together in one line. For example:
Hostname=s390zvm01.suse.de HostIP=10.11.134.65
TIP: Using IPv6 during the Installation
By default you can only assign IPv4 network addresses to your machine. To
enable IPv6 during installation, enter one of the following parameters at the
bootprompt: ipv6=1 (accept IPv4 and IPv6) or ipv6only=1 (accept IPv6
only).
Installation on IBM System z
69
Some of the following parameters are required. If they are missing, the automatic
process pauses and asks you to enter the value manually.
4.4.1 General Parameters
AutoYaST=<URL> Manual=0
The AutoYaST parameter specifies the location of the autoinst.xml control file for automatic installation. The Manual parameter controls if the other
parameters are only default values that still must be acknowledged by the user.
Set this parameter to 0 if all values should be accepted and no questions asked.
Setting AutoYaST implies setting Manual to 0.
Info=<URL>
Specifies a location for a file from which to read additional options. This helps to
overcome the limitations of 10 lines (and 80 characters per line under z/VM) for
the parmfile. More documentation on the Info file can be found in Section 21.1.5,
“Creating the info File” (page 351). Since the Info file can typically only be
accessed through the network on System z, you cannot use it to specify options
required to setup the network, i.e. options described in Section 4.4.2, “Configuring the Network Interface” (page 70). Also other linuxrc specific options
such as for debugging have to be specified in the parmfile to be effective.
TIP: Creating a File with Autoinstallation Information
At the very end of the installation of a system you can check Clone This
System for Autoyast. This creates a ready-to-use profile as /root/
autoinst.xml that can be used to create clones of this particular installation. To create an autoinstallation file from scratch or to edit an existing one,
use the YaST module Autoinstallation. For more information about AutoYaST, refer to Chapter 21, Automated Installation (page 343).
4.4.2 Configuring the Network Interface
IMPORTANT: Configuring the Network Interface
The settings discussed in this section apply only to the network interface
used during installation. Configure additional network interfaces in the in70
Deployment Guide
stalled system by following the instructions given in Section “Configuring a
Network Connection Manually” (Chapter 22, Basic Networking, ↑Administration Guide).
Hostname=zseries.example.com
Enter the fully qualified hostname.
Domain=example.com
Domain search path for DNS. Allows you to use short hostnames instead of fully
qualified ones.
HostIP=192.168.1.2
Enter the IP address of the interface to configure.
Gateway=192.168.1.3
Specify the gateway to use.
Nameserver=192.168.1.4
Specify the DNS server in charge.
InstNetDev=osa
Enter the type of interface to configure. Possible values are osa, hsi. ctc, escon, and iucv. (CTC, ESCON, and IUCV are no longer officially supported).
For the interfaces of type hsi and osa, specify an appropriate netmask and an
optional broadcast address:
Netmask=255.255.255.0
Broadcast=192.168.255.255
For the interfaces of type ctc, escon, and iucv (CTC, ESCON, and IUCV are
no longer officially supported), enter the IP address of the peer:
Pointopoint=192.168.55.20
OsaInterface=<lcs|qdio> OsaMedium=<eth|tr>
For osa network devices, specify the host interface (qdio or lcs) and the
physical medium (eth for ethernet or tr for token ring).
Layer2=<0|1>
For osa QDIO ethernet and hsi devices, specify whether to enable OSI Layer 2
support.
Installation on IBM System z
71
OSAHWAddr=02:00:65:00:01:09
For Layer 2-enabled osa QDIO ethernet devices, specify the manual MAC address. Note that this is distinct from HWAddr, which contains the default MAC
address as detected by linuxrc.
PortNo=<0|1>
For osa network devices, specify the port number (provided the device supports
this feature). The default value is 0.
Each of the interfaces requires certain setup options:
• Interfaces ctc and escon (CTC and ESCON are no longer officially supported):
ReadChannel=0.0.0424
WriteChannel=0.0.0425
ReadChannel specifies the READ channel to use. WriteChannel specifies
the WRITE channel.
• For the ctc interface (no longer officially supported), specify the protocol that
should be used for this interface:
CTCProtocol=<0/1/2>
Valid entries would be:
0
Compatibility mode, also for nonLinux peers other than OS/390 and
z/OS (this is the default mode)
1
Extended mode
2
Compatibility mode with OS/390
and z/OS
• Network device type osa with interface lcs:
ReadChannel=0.0.0124
Portname=1
ReadChannel stands for the channel number used in this setup. A second port
number can be derived from this by adding one to ReadChannel. Portnumber
is used to specify the relative port.
72
Deployment Guide
• Interface iucv:
IUCVPeer=PARTNER
Enter the name of the peer machine.
• Network device type osa with interface qdio for OSA-Express Gigabit Ethernet
and OSA-Express High-speed Token Ring:
ReadChannel=0.0.0524
WriteChannel=0.0.0525
DataChannel=0.0.0526
Portname=FEF400
For ReadChannel, enter the number of the READ channel. For WriteChannel, enter the number of the WRITE channel. DataChannel specifies the DATA channel. For Portname, enter an appropriate port name. Make sure that the
READ channel carries an even device number.
• Interface hsi for HiperSockets and VM guest LANs:
ReadChannel=0.0.0624
WriteChannel=0.0.0625
DataChannel=0.0.0626
For ReadChannel, enter the appropriate number for the READ channel. For
WriteChannel and DataChannel, enter the WRITE and DATA channel
numbers.
4.4.3 Specifying the Installation Source
and YaST Interface
Install=nfs://server/directory/DVD1/
Specify the location of the installation source to use. Possible protocols are nfs,
smb (Samba/CIFS), ftp, tftp and http.
If an ftp, tftp or smb URL is given, specify the username and password with
the URL. These parameters are optional and anonymous or guest login is assumed
if they are not given.
Install=ftp://user:[email protected]/directory/DVD1/
Install=tftp://user:[email protected]/directory/DVD1/
In case of a Samba or CIFS installation, you can also specify the domain that
should be used:
Installation on IBM System z
73
Install=smb://workdomain;user:[email protected]/directory/DVD1/
UseSSH=1 UseVNC=1 Display_IP=192.168.42.42
Depending on which parameter you give, a remote X server, SSH, or VNC will
be used for installation. UseSSH enables SSH installation, UseVNC starts a VNC
server on the installing machine, and Display_IP causes the installing system
to try to connect to an X server at the given address. Only one of these parameters
should be set at any time.
IMPORTANT: X Authentication Mechanism
The direct installation with the X Window System relies on a primitive authentication mechanism based on hostnames. This mechanism is disabled on current SUSE Linux Enterprise Server versions. Installation with
SSH or VNC is preferred.
To allow a connection between YaST and the remote X server, run xhost <IP
address> with the address of the installing machine on the remote machine.
For VNC, specify a password of six to eight characters to use for installation:
VNCPassword=<a password>
For SSH, specify a password of six to eight characters to use for installation:
SSHPassword=<a password>
4.4.4 Example Parmfiles
For an automatic installation with AutoYaST in an LPAR, it is preferable that the
parmfile has just one long line. If multiple lines are desired for readability, use blank
characters at the beginning and end of each line. The maximum number of lines in a
parmfile is 10.
To receive potential error messages on the console, use
linuxrclog=/dev/console
Example 4.15: Parmfile for Installation with NFS, VNC, and IUCV and AutoYaST
with HTTP
ramdisk_size=131072 root=/dev/ram1 ro init=/linuxrc TERM=dumb
instnetdev=iucv iucvpeer=ROUTER01 pointopoint=192.168.0.1
hostip=192.168.0.2
nameserver=192.168.0.3
74
Deployment Guide
install=nfs://192.168.0.4/SLES/SLES-11-s390x/DVD1
autoyast=http://192.168.0.5/autoinst.xml
linuxrclog=/dev/console usevnc=1
vncpassword=testin
Example 4.16: Parmfile for Installation with NFS, SSH, and HSI and AutoYaST
with NFS
ramdisk_size=131072 root=/dev/ram1 ro init=/linuxrc TERM=dumb
AutoYast=nfs://192.168.1.1/autoinst/s390.xml
Hostname=zseries.example.com HostIP=192.168.1.2
Gateway=192.168.1.3 Nameserver=192.168.1.4
InstNetDev=hsi layer2=0
Netmask=255.255.255.128 Broadcast=192.168.1.255
readchannel=0.0.702c writechannel=0.0.702d datachannel=0.0.702e
install=nfs://192.168.1.5/SLES-11-s390x/DVD1/
UseSSH=1 SSHPassword=testing linuxrclog=/dev/console
4.5 Using the vt220 Terminal
Emulator
Recent MicroCode Levels allow the use of an integrated vt220 terminal emulator in
addition to the standard line mode terminal. The vt220 terminal is connected to /
dev/ttyS1. The line mode terminal is connected to /dev/ttyS0. If the vt220
emulation is available, an icon for an integrated vt220 ASCII console appears next to
the icon for the 3215 console on the HMC/SE.
To activate vt220 support on your machine, edit /etc/inittab as user root.
Look for the following line and delete the leading # sign:
#2:2345:respawn:/sbin/mingetty --noclear /dev/ttyS1 xterm
Save the file and run telinit q to pass the changes in /etc/inittab to init.
The vt220 terminal should then be ready to use. If not, try hitting Enter at the terminal
until the login prompt appears.
Make sure that you do not apply the changes as described above to a system that does
not support vt220 terminal emulators. Otherwise, login might become impossible on
this system and you will be shown the following message:
INIT respawning too fast, disabled for 5 minutes.
To redirect the kernel messages at boot time from the system console to the vt220 terminal, add the following entries to the parameters line in /etc/zipl.conf:
console=ttyS0 console=ttyS1
Installation on IBM System z
75
The resulting parameters line would look like the following example:
parameters = "root=/dev/dasda2 TERM=dumb console=ttyS0 console=ttyS1"
Save the changes in /etc/zipl.conf, run zipl, and reboot the system.
4.6 Further In-Depth Information
about IBM System z
IBM has published a number of very interesting documents about their System z platform. Find them at http://www.redbooks.ibm.com.
4.6.1 IBM System z with SUSE Linux
Enterprise Server
Find additional in-depth technical documentation about the kernel and application
topics on IBM System z with SUSE Linux Enterprise Server at the following location:
• http://www.ibm.com/developerworks/linux/lin​
ux390/documentation_novell_suse.html
4.6.2 Hardware
For a first glance at the technical details of some systems, refer to:
• IBM System z10 Enterprise Class Technical Introduction (SG24-7515)
• IBM System z9 Business Class Technical Introduction (SG24-7241)
• Linux on zSeries Fibre Channel Protocol Implementation Guide (SG24-6344)
4.6.3 General Documents about Linux on
IBM System z
A general coverage of Linux on IBM System z can be found in the following documents:
76
Deployment Guide
• Linux on IBM eServer zSeries and S/390: ISP and ASP Solutions (SG24-6299)
These documents might not reflect the current state of Linux, but the principles of
Linux deployment outlined there remain accurate.
4.6.4 Technical Issues of Linux on IBM
System z
Refer to the following documents to get in-depth technical information about the Linux kernel and application topics. Refer to the Internet for up-to-date versions of these
documents for the most recent code drop (http://www.ibm.com/developer​
works/linux/linux390/index.html).
• Linux on System z Device Drivers, Features, and Commands
• zSeries ELF Application Binary Interface Supplement
• Linux on System z Device Drivers, Using the Dump Tools
• IBM System z9-109 Technical Introduction (SG26-6669)
• IBM System z10 Enterprise Class Technical Guide (SG24-7516)
There also is a Redbook for Linux application development on http://
www.redbooks.ibm.com:
• Linux on IBM eServer zSeries and S/390: Application Development (SG24-6807)
4.6.5 Advanced Configurations for Linux
on IBM System z
Refer to the following Redbooks, Redpapers, and links for some more complex IBM
System z scenarios:
• Linux on IBM eServer zSeries and S/390: Large Scale Deployment (SG24-6824)
• Linux on IBM eServer zSeries and S/390: Performance Measuring and Tuning
(SG24-6926)
Installation on IBM System z
77
• Linux with zSeries and ESS: Essentials (SG24-7025)
• IBM TotalStorage Enterprise Storage Server Implementing ESS Copy Services with
IBM eServer zSeries (SG24-5680)
• Linux on IBM zSeries and S/390: High Availability for z/VM and Linux
(REDP-0220)
• Saved Segments Planning and Administration
http://publibz.boulder.ibm.com/epubs/pdf/hcsg4a00.pdf
• Linux on System z documentation for "Development stream"
http://www.ibm.com/developerworks/linux/lin​
ux390/development_documentation.html
78
Deployment Guide
Part II. Manual Deployment
5
Deployment Strategies
There are several different ways to deploy SUSE Linux Enterprise Server. Choose
from various approaches ranging from a local installation using physical media or
a network installation server to a mass deployment using a remote-controlled, highly-customized, and automated installation technique. Select the method that best
matches your requirements.
5.1 Deploying up to 10
Workstations
If your deployment of SUSE Linux Enterprise Server only involves 1 to 10 workstations, the easiest and least complex way of deploying SUSE Linux Enterprise
Server is a plain manual installation as featured in Chapter 6, Installation with
YaST (page 93). Manual installation can be done in several different ways, depending on your requirements:
Installing from the SUSE Linux Enterprise Server Media (page 82)
Consider this approach if you want to install a single, disconnected workstation.
Installing from a Network Server Using SLP (page 82)
Consider this approach if you have a single workstation or a small number of
workstations and if a network installation server announced via SLP is available.
Deployment Strategies
81
Installing from a Network Server (page 83)
Consider this approach if you have a single workstation or a small number of
workstations and if a network installation server is available.
Table 5.1: Installing from the SUSE Linux Enterprise Server Media
Installation Source
SUSE Linux Enterprise Server media
kit
Tasks Requiring Manual Interaction
• Inserting the installation media
• Booting the installation target
• Changing media
• Determining the YaST installation
scope
• Configuring the system with YaST
system
Remotely Controlled Tasks
None
Details
“Installing from the SUSE Linux Enterprise Server Media (DVD, CD,
USB)” (page 93)
Table 5.2: Installing from a Network Server Using SLP
Installation Source
Network installation server holding
the SUSE Linux Enterprise Server installation media
Tasks Requiring Manual Interaction
• Inserting the boot disk
• Booting installation target
• Determining the YaST installation
scope
• Configuring the system with YaST
82
Deployment Guide
Remotely Controlled Tasks
None, but this method can be combined with VNC
Details
Section 6.1.1, “Installing
from a Network Server Using
SLP” (page 95)
Table 5.3: Installing from a Network Server
Installation Source
Network installation server holding
the SUSE Linux Enterprise Server installation media
Tasks Requiring Manual Interaction
• Inserting the boot disk
• Providing boot options
• Booting the installation target
• Determining the YaST installation
scope
• Configuring the system with YaST
Remotely Controlled Tasks
None, but method can be combined
with VNC
Details
Section 6.1.2, “Installing from
a Network Source without
SLP” (page 96)
5.2 Deploying up to 100
Workstations
With a growing number of workstations to install, you certainly do not want to install
and configure each one of them manually. There are many automated or semiautoDeployment Strategies
83
mated approaches as well as several options for performing an installation with minimal to no physical user interaction.
Before considering a fully-automated approach, take into account that the more complex the scenario gets the longer it takes to set up. If a time limit is associated with
your deployment, it might be a good idea to select a less complex approach that can
be carried out much more quickly. Automation makes sense for huge deployments
and those that need to be carried out remotely.
Choose from the following options:
Simple Remote Installation via VNC—Static Network Configuration (page 85)
Consider this approach in a small to medium scenario with a static network setup.
A network, network installation server, and VNC viewer application are required.
Simple Remote Installation via VNC—Dynamic Network
Configuration (page 86)
Consider this approach in a small to medium scenario with dynamic network setup through DHCP. A network, network installation server, and VNC viewer application are required.
Remote Installation via VNC—PXE Boot and Wake on LAN (page 86)
Consider this approach in a small to medium scenario that needs to be installed
via the network and without physical interaction with the installation targets. A
network, a network installation server, network boot images, network bootable
target hardware, and a VNC viewer application are required.
Simple Remote Installation via SSH—Static Network Configuration (page 87)
Consider this approach in a small to medium scenario with static network setup.
A network, network installation server, and SSH client application are required.
Remote Installation via SSH—Dynamic Network Configuration (page 87)
Consider this approach in a small to medium scenario with dynamic network setup through DHCP. A network, network installation server, and SSH client application are required.
Remote Installation via SSH—PXE Boot and Wake on LAN (page 88)
Consider this approach in a small to medium scenario that needs to be installed
via the network and without physical interaction with the installation targets. A
network, a network installation server, network boot images, network bootable
target hardware, and an SSH client application are required.
84
Deployment Guide
Simple Mass Installation (page 89)
Consider this approach for large deployments to identical machines. If configured
to use network booting, physical interaction with the target systems is not needed
at all. A network, a network installation server, a remote controlling application
(such as a VNC viewer or an SSH client), and an AutoYaST configuration profile
are required. If using network boot, a network boot image and network bootable
hardware are required, as well.
Rule-Based Autoinstallation (page 90)
Consider this approach for large deployments to various types of hardware. If
configured to use network booting, physical interaction with the target systems is
not needed at all. A network, a network installation server, a remote controlling
application (such as a VNC viewer or an SSH client), and several AutoYaST configuration profiles as well (as a rule setup for AutoYaST) are required. If using
network boot, a network boot image and network bootable hardware are required,
as well.
Table 5.4: Simple Remote Installation via VNC—Static Network Configuration
Installation Source
Network
Preparations
• Setting up an installation source
• Booting from the installation media
Control and Monitoring
Remote: VNC
Best Suited For
Small to medium scenarios with varying hardware
Drawbacks
• Each machine must be set up individually
• Physical access is needed for booting
Details
Section 14.1.1, “Simple Remote Installation via VNC—Static Network
Configuration” (page 246)
Deployment Strategies
85
Table 5.5: Simple Remote Installation via VNC—Dynamic Network Configuration
Installation Source
Network
Preparations
• Setting up the installation source
• Booting from the installation media
Control and Monitoring
Remote: VNC
Best Suited For
Small to medium scenarios with varying hardware
Drawbacks
• Each machine must be set up individually
• Physical access is needed for booting
Details
Section 14.1.2, “Simple Remote Installation via VNC—Dynamic Network Configuration” (page 247)
Table 5.6: Remote Installation via VNC—PXE Boot and Wake on LAN
Installation Source
Network
Preparations
• Setting up the installation source
• Configuring DHCP, TFTP, PXE
boot, and WOL
• Booting from the network
86
Control and Monitoring
Remote: VNC
Best Suited For
• Small to medium scenarios with
varying hardware
Deployment Guide
• Completely remote installs; crosssite deployment
Drawbacks
Each machine must be set up manually
Details
Section 14.1.3, “Remote Installation
via VNC—PXE Boot and Wake on
LAN” (page 249)
Table 5.7: Simple Remote Installation via SSH—Static Network Configuration
Installation Source
Network
Preparations
• Setting up the installation source
• Booting from the installation media
Control and Monitoring
Remote: SSH
Best Suited For
• Small to medium scenarios with
varying hardware
• Low bandwidth connections to target
Drawbacks
• Each machine must be set up individually
• Physical access is needed for booting
Details
Section 14.1.4, “Simple Remote Installation via SSH—Static Network
Configuration” (page 250)
Table 5.8: Remote Installation via SSH—Dynamic Network Configuration
Installation Source
Network
Deployment Strategies
87
Preparations
• Setting up the installation source
• Booting from installation media
Control and Monitoring
Remote: SSH
Best Suited For
• Small to medium scenarios with
varying hardware
• Low bandwidth connections to target
Drawbacks
• Each machine must be set up individually
• Physical access is needed for booting
Details
Section 14.1.5, “Simple Remote Installation via SSH—Dynamic Network Configuration” (page 251)
Table 5.9: Remote Installation via SSH—PXE Boot and Wake on LAN
Installation Source
Network
Preparations
• Setting up the installation source
• Configuring DHCP, TFTP, PXE
boot, and WOL
• Booting from the network
Control and Monitoring
Remote: SSH
Best Suited For
• Small to medium scenarios with
varying hardware
• Completely remote installs; crosssite deployment
88
Deployment Guide
• Low bandwidth connections to target
Drawbacks
Each machine must be set up individually
Details
Section 14.1.6, “Remote Installation
via SSH—PXE Boot and Wake on
LAN” (page 253)
Table 5.10: Simple Mass Installation
Installation Source
Preferably network
Preparations
• Gathering hardware information
• Creating AutoYaST profile
• Setting up the installation server
• Distributing the profile
• Setting up network boot (DHCP,
TFTP, PXE, WOL)
or
Booting the target from installation
media
Control and Monitoring
Local or remote through VNC or SSH
Best Suited For
• Large scenarios
• Identical hardware
• No access to system (network boot)
Drawbacks
Applies only to machines with identical hardware
Deployment Strategies
89
Details
Section 21.1, “Simple Mass
Installation” (page 343)
Table 5.11: Rule-Based Autoinstallation
Installation Source
Preferably network
Preparations
• Gathering hardware information
• Creating AutoYaST profiles
• Creating AutoYaST rules
• Setting up the installation server
• Distributing the profile
• Setting up network boot (DHCP,
TFTP, PXE, WOL)
or
Booting the target from installation
media
Control and Monitoring
Local or remote through SSH or VNC
Best Suited For
• Varying hardware
• Cross-site deployments
90
Drawbacks
Complex rule setup
Details
Section 21.2, “Rule-Based
Autoinstallation” (page 355)
Deployment Guide
5.3 Deploying More than 100
Workstations
Most of the considerations brought up for medium installation scenarios in Section 5.1, “Deploying up to 10 Workstations” (page 81) still hold true for large
scale deployments. However, with a growing number of installation targets, the benefits of a fully automated installation method outweigh its drawbacks.
It pays off to invest a considerable amount of time to create a sophisticated rule and
class framework in AutoYaST to match the requirements of a huge deployment site.
Not having to touch each target separately can save you a tremendous amount of time
depending on the scope of your installation project.
As an alternative, and if user settings should be done during the first bootup, create preload images with kiwi and firstboot. Deploying such images could even be
done by a PXE boot server specialized for this task. For more details, see Chapter 17,
KIWI (page 313), Chapter 21, Automated Installation (page 343), and Chapter 20, Deploying Customized Preinstallations (page 329).
Deployment Strategies
91
Installation with YaST
After your hardware has been prepared for the installation of SUSE® Linux Enterprise Server as described in Part I, “Architecture Specific Installation
Considerations” (page 5) and after the connection with the installation system has
been established, you are presented with the interface of SUSE Linux Enterprise
Server's system assistant YaST. YaST guides you through the entire installation and
configuration procedure.
6
6.1 Choosing the Installation
Method
After having selected the installation medium, determine the suitable installation
method and boot option that best matches your needs:
Installing from the SUSE Linux Enterprise Server Media (DVD, CD, USB)
Choose this option if you want to perform a stand-alone installation and do not
want to rely on a network to provide the installation data or the boot infrastructure. The installation proceeds exactly as outlined in Section 6.2, “The Installation
Workflow” (page 96).
Installing from a Network Server
Choose this option if you have an installation server available in your network or
want to use an external server as the source of your installation data. This setup
can be configured to boot from physical media (Floppy, CD/DVD, or hard disk)
or configured to boot via network using PXE/BOOTP. Refer to Section 6.1.1,
Installation with YaST
93
“Installing from a Network Server Using SLP” (page 95), Section 6.1.2, “Installing from a Network Source without SLP” (page 96), or Chapter 14, Remote Installation (page 245) for details.
SUSE Linux Enterprise Server supports several different boot options from which
you can choose, depending on the hardware available and on the installation scenario you prefer. Booting from the SUSE Linux Enterprise Server media is the most
straightforward option, but special requirements might call for special setups:
Table 6.1: Boot Options
Boot Option
Description
DVD
This is the easiest boot option. This
option can be used if the system has
a local DVD-ROM drive that is supported by Linux.
USB Mass Storage Device
In case your machine is not equipped
with an optical drive, you can boot the
installation image from a USB mass
storage device such as a USB stick.
To create a bootable USB storage
device, you need to copy either the
DVD or the Mini CD iso image to the
device using the dd command (the
USB device must not be mounted, all
data on the device will be erased):
dd if=PATH_TO_ISO_IMAGE
of=USB_STORAGE_DEVICE bs=4M
dd is available on Linux and
MacOS by default. A Microsoft Windows* version can
be downloaded from http://
www.chrysocome.net/dd.
IMPORTANT: Compatibility
Please note that booting from
a USB Mass Storage Device is
94
Deployment Guide
Boot Option
Description
not supported on UEFI machines
(this includes the complete ia64
architecture) and on the ppc64
architecture.
PXE or BOOTP
Booting over the network must be
supported by the system's BIOS or
firmware, and a boot server must
be available in the network. This
task can also be handled by another
SUSE Linux Enterprise Server system. Refer to Chapter 14, Remote
Installation (page 245) for more information.
Hard Disk
SUSE Linux Enterprise Server installation can also be booted from the
hard disk. To do this, copy the kernel (linux) and the installation system (initrd) from the directory /
boot/architecture/ on the installation media to the hard disk and
add an appropriate entry to the existing boot loader of a previous SUSE
Linux Enterprise Server installation.
TIP: Booting from DVD on UEFI machines
#amd64 em64t: DVD1 can be used as a boot medium for machines
equipped with UEFI (Unified Extensible Firmware Interface). Refer to your
vendor's documentation for specific information. If booting fails, try to enable
CSM (Compatibility Support Module) in your firmware. ◄
6.1.1 Installing from a Network Server
Using SLP
Installation with YaST
95
If your network setup supports OpenSLP and your network installation source has
been configured to announce itself via SLP (described in Section 14.2, “Setting Up
the Server Holding the Installation Sources” (page 254)), boot the system, press F4
in the boot screen and select SLP from the menu.
The installation program configures the network connection with DHCP and retrieves
the location of the network installation source from the OpenSLP server. If the automatic DHCP network configuration fails, you are prompted to enter the appropriate parameters manually. The installation then proceeds as described below with the
exception of the network configuration step that is needed prior to adding additional
repositories. This step is not needed as the network is already configured and active at
this point.
6.1.2 Installing from a Network Source
without SLP
If your network setup does not support OpenSLP for the retrieval of network installation sources, boot the system and press F4 in the boot screen to select the desired network protocol (NFS, HTTP, FTP, or SMB/CIFS). Provide the server's address and the
path to the installation media.
The installation program automatically configures the network connection with
DHCP. If this configuration fails, you are prompted to enter the appropriate parameters manually. The installation retrieves the installation data from the source specified. The installation then proceeds as described below with the exception of the network configuration step needed prior to adding additional repositories. This step is not
needed as the network is already configured and active at this point.
6.2 The Installation Workflow
The SUSE Linux Enterprise Server installation is split into three main parts: preparation, installation, and configuration. During the preparation phase you configure some
basic parameters such as language, time, hard disk setup and installation scope. In the
non-interactive installation phase the software is installed and the system is prepared
for the first boot. Upon finishing the installation the machine reboots into the newly
installed system and starts the final system configuration. In this stage, network and
Internet access, as well as hardware components such as printers, are set up.
96
Deployment Guide
6.3 IBM POWER: System Start-Up
for Network Installation
For IBM POWER platforms, the system is booted (IPL, Initial Program Load) as described in Section 3.2, “Preparation” (page 23). For a network installation, SUSE Linux Enterprise Server does not show a splash screen or a boot loader command line on
these systems. During the installation load the kernel manually. YaST starts with its
installation screen as soon as a connection has been established to the installation system via VNC, X, or SSH. Because there is no splash screen or boot loader command
line, kernel or boot parameters cannot be entered on the screen, but must be included
in the kernel image using the mkzimage_cmdline utility.
TIP: IBM POWER: The Next Steps
To install, follow the description of the installation procedure with YaST starting from Section 6.8, “Welcome” (page 105).
6.4 IBM System z: System Start-Up
for Installation
For IBM System z platforms, the system is booted (IPL, Initial Program Load) as
described in Section 4.2.4, “IPLing the SUSE Linux Enterprise Server Installation
System” (page 56). SUSE Linux Enterprise Server does not show a splash screen on
these systems. During the installation, load the kernel, initrd, and parmfile manually.
YaST starts with its installation screen as soon as a connection has been established to
the installation system via VNC, X, or SSH. Because there is no splash screen, kernel
or boot parameters cannot be entered on screen, but must be specified in a parmfile
(see Section 4.4, “The parmfile—Automating the System Configuration” (page 69)).
TIP: IBM System z: The Next Steps
To install, follow the description of the installation procedure with YaST starting from Section 6.8, “Welcome” (page 105).
6.5 System Start-Up for Installation
Installation with YaST
97
You can install SUSE Linux Enterprise Server from local installation sources, such as
the SUSE Linux Enterprise Server CDs or DVD, or from network source of an FTP,
HTTP, NFS, or SMB server. Any of these approaches requires physical access to the
system to install as well as user interaction during the installation. The installation procedure is basically the same regardless of the installation source. Any exceptions are
sufficiently highlighted in the following workflow description. For a description on
how to perform non-interactive, automated installations, refer to Part IV, “Automated
Installations” (page 341).
6.6 The Boot Screen on Machines
Equipped with Traditional BIOS
The boot screen displays a number of options for the installation procedure. Boot
from Hard Disk boots the installed system and is selected by default, because the CD
is often left in the drive. Select one of the other options with the arrow keys and press
Enter to boot it. The relevant options are:
Installation
The normal installation mode. All modern hardware functions are enabled. In
case the installation fails, see “F5Kernel ” (page 100) for boot options that disable potentially problematic functions.
Repair Installed System
Boots into the graphical repair system. More information on repairing an installed
system is available in Section “Recovering a Corrupted System” (Chapter 36,
Common Problems and Their Solutions, ↑Administration Guide).
Rescue System
Starts a minimal Linux system without a graphical user interface. For more information, see Section “Using the Rescue System” (Chapter 36, Common Problems
and Their Solutions, ↑Administration Guide).
Check Installation Media
This option is only available when you install from media created from downloaded ISOs. In this case it is recommended to check the integrity of the installation medium. This option starts the installation system before automatically
98
Deployment Guide
checking the media. In case the check was successful, the normal installation routine starts. If a corrupt media is detected, the installation routine aborts.
Firmware Test
Starts a BIOS checker that validates ACPI and other parts of your BIOS.
Memory Test
Tests your system RAM using repeated read and write cycles. Terminate the test
by rebooting. For more information, see Section “Fails to Boot” (Chapter 36,
Common Problems and Their Solutions, ↑Administration Guide).
Figure 6.1: The Boot Screen on Machines with a Traditional BIOS
Use the function keys indicated in the bar at the bottom of the screen to change the
language, screen resolution, installation source or to add an additional driver from
your hardware vendor:
F1Help
Get context-sensitive help for the active element of the boot screen. Use the arrow keys to navigate, Enter to follow a link, and Esc to leave the help screen.
F2Language
Select the display language and a corresponding keyboard layout for the installation. The default language is English (US).
Installation with YaST
99
F3Video Mode
Select various graphical display modes for the installation. Select Text Mode if the
graphical installation causes problems.
F4Source
Normally, the installation is performed from the inserted installation medium.
Here, select other sources, like FTP or NFS servers. If the installation is deployed
on a network with an SLP server, select an installation source available on the
server with this option. Find information about SLP in Chapter 23, SLP Services
in the Network (↑Administration Guide).
F5Kernel
If you encounter problems with the regular installation, this menu offers to disable a few potentially problematic functions. If your hardware does not support
ACPI (advanced configuration and power interface) select No ACPI to install
without ACPI support. No local APIC disables support for APIC (Advanced Programmable Interrupt Controllers) which may cause problems with some hardware. Safe Settings boots the system with the DMA mode (for CD/DVD-ROM
drives) and power management functions disabled.
If you are not sure, try the following options first: Installation—ACPI Disabled or
Installation—Safe Settings. Experts can also use the command line (Boot Options)
to enter or change kernel parameters.
F6Driver
Press this key to notify the system that you have an optional driver update for
SUSE Linux Enterprise Server. With File or URL, load drivers directly before the
installation starts. If you select Yes, you are prompted to insert the update disk at
the appropriate point in the installation process.
TIP: Getting Driver Update Disks
Driver updates for SUSE Linux Enterprise are provided at http://
drivers.suse.com/. These drivers have been created via the Partner
Linux Driver Program.
TIP: Using IPv6 during the Installation
By default you can only assign IPv4 network addresses to your machine. To
enable IPv6 during installation, enter one of the following parameters at the
100
Deployment Guide
bootprompt: ipv6=1 (accept IPv4 and IPv6) or ipv6only=1 (accept IPv6
only).
After starting the installation, SUSE Linux Enterprise Server loads and configures a
minimal Linux system to run the installation procedure. To view the boot messages
and copyright notices during this process, press Esc. On completion of this process,
the YaST installation program starts and displays the graphical installer.
TIP: Installation without a Mouse
If the installer does not detect your mouse correctly, use Tab for navigation,
arrow keys to scroll, and Enter to confirm a selection. Various buttons or selection fields contain a letter with an underscore. Use Alt + Letter to select a
button or a selection directly instead of navigating there with the Tab button.
6.6.1 Providing Data to Access an SMT
Server
By default, updates for SUSE Linux Enterprise Server are delivered by the Novell
Customer Center. If your network provides a so called SMT server to provide a local
update source, you need to equip the client with the server's URL. Client and server
communicate solely via HTTPS protocol, therefore you also need to enter a path to
the server's certificate if the certificate was not issued by a certificate authority. This
information can either be entered at the boot prompt (as described here) or during the
registration process as described in Section “Local Registration Server” (page 127).
regurl
URL of the SMT server. This URL has a fixed format https://FQN/center/regsvc/ FQN has to be a fully qualified hostname of the SMT server. Example:
regurl=https://smt.example.com/center/regsvc/
regcert
Location of the SMT server's certificate. Specify one of the following locations:
URL
Remote location (http, https or ftp) from which the certificate can be downloaded. Example:
regcert=http://smt.example.com/smt-ca.crt
Installation with YaST
101
Floppy
Specifies a location on a floppy. The floppy has to be inserted at boot time,
as you will not be prompted to insert it if it is missing. The value has to start
with the string floppy followed by the path to the certificate. Example:
regcert=floppy/smt/smt-ca.crt
local path
Absolute path to the certificate on the local machine. Example:
regcert=/data/inst/smt/smt-ca.cert
Interactive
Use ask to open a pop-up menu during the installation where you can specify the path to the certificate. Do not use this option with AutoYaST. Example
regcert=ask
Deactivate certificate installation
Use done if either the certificate will be installed by an add-on product, or
if you are using a certificate issued by an official certificate authority. Example:
regcert=done
WARNING: Beware of typing errors
Make sure the values you enter are correct. If regurl has not been specified correctly, the registration of the update source will fail. If a wrong value
for regcert has been entered, you will be prompted for a local path to the certificate.
In case regcert is not specified, it will default to http://FQN/smt.crt with
FQN being the name of the SMT server.
6.6.2 Configuring an Alternative Data
Server for supportconfig
The data that supportconfig (see Chapter 2, Gathering System Information for Support
(↑Administration Guide) for more information) gathers is sent to the Novell Customer
Center by default. It is also possible to set up a local server to collect this data. If such
a server is available on your network, you need to set the server's URL on the client.
This information has to be entered at the boot prompt.
102
Deployment Guide
supporturl
URL of the server. The URL has the format http://FQN/Path/ FQN has to
be full qualified hostname of the server, Path has to be replaced with the location on the server. Example:
supporturl=http://support.example.com/supportconfig/data/
6.7 The Boot Screen on Machines
Equipped with UEFI
UEFI (Unified Extensible Firmware Interface) is a new industry standard which replaces and extends the traditional BIOS. The latest UEFI implementations contain the
“Secure Boot” extension, that prevents booting malicious code by only allowing signed
boot loaders to be executed. See Chapter 12, UEFI (Unified Extensible Firmware Interface) (↑Administration Guide) for more information.
The boot manager GRUB, used to boot machines with a traditional BIOS, does not
support UEFI, therefore GRUB is replaced with ELILO. If Secure Boot is enabled, a
GRUB2 UEFI module is used via an ELILO compatibility layer. From an administrative and user perspective, both boot manager implementations behave the same and
are referred to as ELILO in the following.
TIP: UEFI and Secure Boot are Supported by Default
The installation routine of SUSE Linux Enterprise automatically detects if the
machine is equipped with UEFI. All installation sources also support Secure
Boot. If an EFI system partition already exists on dual boot machines (from a
Microsoft Windows 8 installation, for example), it will automatically be detected and used. Partition tables will be written as GPT on UEFI systems.
WARNING: Using Non-Inbox Drivers with Secure Boot
There is no support for adding non-inbox drivers (that is, drivers that do not
come with SLE) during installation with Secure Boot enabled. The signing
key used for SolidDriver/PLDP is not trusted by default.
To solve this problem, it is necessary to either add the needed keys to the
firmware database via firmware/system management tools before the installation or to use a bootable ISO that will enroll the needed keys in the MOK list
Installation with YaST
103
at first boot. For more information, see Section “Secure Boot” (Chapter 12,
UEFI (Unified Extensible Firmware Interface), ↑Administration Guide).
The boot screen displays a number of options for the installation procedure. Change
the selected option with the arrow keys and press Enter to boot it. The relevant options are:
Installation
The normal installation mode.
Rescue System
Starts a minimal Linux system without a graphical user interface. For more information, see Section “Using the Rescue System” (Chapter 36, Common Problems
and Their Solutions, ↑Administration Guide).
Check Installation Media
This option is only available when you install from media created from downloaded ISOs. In this case it is recommended to check the integrity of the installation medium. This option starts the installation system before automatically
checking the media. In case the check was successful, the normal installation routine starts. If a corrupt media is detected, the installation routine aborts.
Figure 6.2: The Boot Screen on Machines with UEFI
104
Deployment Guide
ELILO on SUSE Linux Enterprise Server does not support a graphical boot screen or
a boot prompt. In order to add additional boot parameters you need to edit the respective boot entry. Highlight it using the arrow keys and press E. See the on-screen help
for editing hints (note that only an English keyboard is available at this time). The Installation entry will look similar to the following:
setparams 'Installation'
set gfxpayload=keep
echo 'Loading kernel ...'
linuxefi /boot/x86_64/loader/linux
echo 'Loading initial ramdisk ...'
initrdefi /boot/x86_64/loader/initrd
Add space separated parameters to the end of the line starting with linuxefi. A list
of parameters is available at https://en.opensuse.org/Linuxrc. In the
following example the installation language is set to German:
linuxefi /boot/x86_64/loader/linux Language=de_DE
To boot the edited entry, press F10. If you access the machine via serial console,
press Esc + 0.
6.8 Welcome
Start the installation of SUSE Linux Enterprise Server by choosing your language.
Changing the language will automatically preselect a corresponding keyboard layout. Override this proposal by selecting a different keyboard layout from the dropdown menu. The language selected here is also used to assume a time zone for the system clock. This setting—along with the selection of secondary languages to install on
your system—can be modified later in the Installation Summary, described in Section 6.14, “Installation Settings” (page 114). For information about language settings in the installed system, see Chapter 13, Changing Language and Country Settings
with YaST (page 237).
Read the license agreement that is displayed beneath the language and keyboard selection thoroughly. Use License Translations... to access translations. If you agree to the
terms, check I Agree to the License Terms and click Next to proceed with the installation. If you do not agree to the license agreement, you cannot install SUSE Linux Enterprise Server; click Abort to terminate the installation.
Installation with YaST
105
Figure 6.3: Welcome
6.9 IBM System z: Hard Disk
Configuration
When installing on IBM System z platforms, the language selection dialog is followed
by a dialog to configure the attached hard disks. Select DASD, Fibre Channel Attached SCSI Disks (zFCP), or iSCSI for installation of SUSE Linux Enterprise Server. The DASD and zFCP configuration buttons are only available if the corresponding devices are attached. For instructions on how to configure iSCSI disks, refer to
Section “Installing iSCSI Target and Initiator” (Chapter 14, Mass Storage over IP Networks: iSCSI , ↑Storage Administration Guide).
TIP: Adding DASD or zFCP Disks at a Later Stage
Adding DASD or zFCP disks is not only possible during the installation workflow, but also when the installation proposal is shown. To add disks at that
stage, click Expert and scroll down. The DASD and zFCP entries are shown
at the very bottom.
106
Deployment Guide
After adding the disks, reread the partition table. Return to the installation
proposal screen and choose Partitioning then select Reread Partition Table.
This updates the new partition table.
6.9.1 Configuring DASD Disks
After selecting Configure DASD Disks, an overview lists all available DASDs. To get
a clearer picture of the available devices, use the entry field located above the list to
specify a range of channels to display. To filter the list according to such a range, select Filter.
Figure 6.4: IBM System z: Selecting a DASD
Specify the DASDs to use for the installation by selecting the corresponding entries
in the list. Click Select or Deselect. Activate and make the DASDs available for the installation by selecting Perform Action > Activate. To format the DASDs, select Perform Action > Format right away or use the YaST partitioner later as described in Section 15.1, “Using the YaST Partitioner” (page 281).
6.9.2 Configuring zFCP Disks
To use zFCP disks for the SUSE Linux Enterprise Server installation, select Configure
zFCP Disks in the selection dialog. This opens a dialog with a list of the zFCP disks
Installation with YaST
107
available on the system. In this dialog, select Add to open another dialog in which to
enter zFCP parameters.
To make a zFCP disk available for the SUSE Linux Enterprise Server installation,
choose an available Channel Number from the drop-down list. Get WWPNs (World
Wide Port Number) and Get LUNs (Logical Unit Number) return lists with available
WWPNs and FCP-LUNs, respectively, to choose from. When completed, exit the
zFCP dialog with Next and the general hard disk configuration dialog with Finish to
continue with the rest of the configuration.
6.10 Media Check
The media check dialog only appears if you install from media created from downloaded ISOs. If you install from the original media kit, the dialog is skipped.
The media check examines the integrity of a medium. To start it, select the drive that
contains the installation medium and click Start Check. The check can take some time.
To test multiple media, wait until a result message appears in the dialog before changing the medium. If the last medium checked is not the one you started the installation
with, YaST prompts for the appropriate medium before continuing with the installation.
If using ISO images (for example, for installing add-on products), click Check ISO
File and choose the image via the file dialog.
WARNING: Failure of Media Check
If the media check fails, your medium is damaged. Do not continue the installation because installation may fail or you may loose your data. Replace the
broken medium and restart the installation process.
If the media check turns out positive, click Next to continue the installation.
6.11 Installation Mode
After a system analysis (where YaST probes for storage devices and tries to find other
installed systems on your machine) the available installation modes are displayed.
108
Deployment Guide
New installation
Select this option to start a new installation from scratch.
Update
Select this option to update an existing installation to a newer version. For
more information about system update, see Chapter 7, Updating SUSE Linux
Enterprise (page 135).
Repair Installed System
Choose this option to repair a damaged system that is already installed. More information is available in Section “Recovering a Corrupted System” (Chapter 36,
Common Problems and Their Solutions, ↑Administration Guide).
Figure 6.5: Installation Mode
Check Include Add-On Products from Separate Media to include add-on products during the installation. An add-on product can include extensions, third-party products
and drivers or additional software for your system.
TIP: Installing Product Patches from an SMT Server on Installation
In case your organization provides the update channel for SUSE Linux Enterprise Server via an SMT server, it is possible to specify this channel as an
Add-On product by entering its HTTP address. As a consequence, the sysInstallation with YaST
109
tem will be installed with the most current packages without having to apply
the updates at the end of the installation.
Click Next to proceed. If you selected to include an add-on product, proceed with Section 6.11.1, “Add-On Products” (page 110), otherwise skip the next section and advance to Section 6.12, “Clock and Time Zone” (page 111).
6.11.1 Add-On Products
Add-on products can be installed either from a local source (CD, DVD, or directory) or from a network source (HTTP, FTP, NFS, CIFS,...). When installing from a
network source, you need to configure the network first (unless you are performing a
network installation—in this case the existing network configuration is used). Choose
Yes, Run the Network Setup and proceed as described in Section 6.11.1.1, “Network
Setup” (page 111). If the add-on product is available locally, select No, Skip the
Network Setup.
Click Next and specify the product source. Source types available are CD, DVD, Hard
Disk, USB Mass Storage, a Local Directory or a Local ISO Image (if no network was
configured). If the add-on product is available on removable media, the system automatically mounts the media and reads its contents. If the add-on product is available
on hard disk, choose Hard Disk to install from an unmounted hard drive, or Local Directory/Local ISO Image to install from the local file system. Add-on products may be
delivered as a repository or as a set of RPM files. In the latter case, check Plain RPM
Directory. Whenever a network is available, you can choose from additional remote
sources such as HTTP, SLP, FTP, etc. It is also possible to specify a URL directly.
Check Download Repository Description Files to download the files describing the
repository now. If unchecked, they will be downloaded once the installation starts.
Proceed with Next and insert a CD or DVD if required. Depending on the product's
content it may be necessary to accept additional license agreements.
It is also possible to configure add-on products later. Using add-on products on the installed system is described in Chapter 10, Installing Add-On Products (page 213).
TIP: Driver Updates
You can also add driver update repositories via the Add-On Products dialog. Driver updates for SUSE Linux Enterprise are provided at http://
110
Deployment Guide
drivers.suse.com/. These drivers have been created via the Partner
Linux Driver Program.
6.11.1.1 Network Setup
When invoking the network setup, YaST scans for available network cards. If more
than one network card is found, you must choose the card to configure from the list.
If an ethernet network adapter is not already connected, a warning will open. Make
sure the network cable is plugged in and choose Yes, Use It. If your network is
equipped with a DHCP server, choose Automatic Address Setup (via DHCP). To manually set up the network choose Static Address Setup and specify IP Address, Netmask,
Default Gateway IP, and the DNS Server IP.
Some networks require the use of a proxy server to access the Internet. Tick the check
box Use Proxy for Accessing the Internet and enter the appropriate specifications.
Click Accept to perform the network setup. The installation procedure will continue
with the add-on products or repositories setup as described in Section 6.11.1, “AddOn Products” (page 110).
6.12 Clock and Time Zone
In this dialog, select your region and time zone. Both are preselected according to the
selected installation language. To change the preselected values, either use the map or
the drop down lists for Region and Time Zone. When using the map, point the cursor
at the rough direction of your region and left-click to zoom. Now choose your country
or region by left-clicking. Right-click to return to the world map.
Installation with YaST
111
Figure 6.6: Clock and Time Zone
To set up the clock, choose whether the Hardware Clock is Set to UTC. If you run another operating system on your machine, such as Microsoft Windows, it is likely your
system uses local time instead. If you only run Linux on your machine, set the hardware clock to UTC and have the switch from standard time to daylight saving time
performed automatically.
IMPORTANT: Set the Hardware Clock to UTC
The switch from standard time to daylight saving time (and vice versa) can
only be performed automatically when the hardware clock (CMOS clock) is
set to UTC. This also applies if you use automatic time synchronization with
NTP, because automatic syncing will only be performed if the time difference
between the hardware and system clock is less than 15 minutes.
Since a wrong system time can cause severe problems (missed backups,
dropped mail messages, mount failures on remote file systems, etc.) it is
strongly recommended to always set the hardware clock to UTC.
If a network is already configured, you can configure time synchronization with an
NTP server. Click Change to either alter the NTP settings or to Manually set the time.
See Chapter 24, Time Synchronization with NTP (↑Administration Guide) for more in112
Deployment Guide
formation on configuring the NTP service. When finished, click Accept to continue
the installation.
NOTE: Time Cannot be Changed on IBM System z
Since the operating system is not allowed to change time and date directly,
the Change option is not available on IBM System z.
6.13 Server Base Scenario
In SUSE Linux Enterprise Server, you can choose from three base scenarios. The selected scenario affects the package selection.
Physical Machine
Choose this scenario when installing on a “real” machine or a fully virtualized
guest.
Virtual Machine
Choose this scenario when installing a paravirtualized guest.
XEN Virtualization Host
Choose this scenario when installing on a machine that should serve as a XEN
host.
Installation with YaST
113
Figure 6.7: Server Base Scenario
6.14 Installation Settings
On the last step before the real installation takes place, you can alter installation settings suggested by YaST and also review the settings you made so far. Basic settings
can be changed in the Overview tab, advanced options are available on the Experts tab.
To modify the suggestions, either click Change and select the category to change or
click on one of the headlines. After configuring any of the items presented in these dialogs, you are always returned to the Installation Settings window, which is updated
accordingly.
114
Deployment Guide
Figure 6.8: Installation Settings
TIP: Restoring the Default Settings
You can reset all changes to the defaults by clicking Change > Reset to Defaults. YaST then shows the original proposal again.
6.14.1 Partitioning (Overview)
Review and, if necessary, change the partition setup proposed by the system. Changing the partition setup either lets you partition a specific disk or, when choosing
Custom Partitioning, apply your own partitioning scheme. Modifying the partition setup opens the Expert Partitioner described in Section 15.1, “Using the YaST
Partitioner” (page 281).
TIP: Btrfs as a default file system
The default partitioning scheme is based on Ext3 file system. To use Btrfs as
a default file system instead, click Partitioning in the Overview tab and check
Use Btrfs as Default Filesystem
Installation with YaST
115
NOTE: Using Minidisks in z/VM
If SUSE Linux Enterprise Server is installed on minidisks in z/VM, which reside on the same physical disk, the access path of the minidisks (/dev/disk/
by-id/) is not unique but rather the ID of the physical disk. So if two or more
minidisks are on the same physical disk, they all have the same ID.
To avoid problems when mounting the minidisks, always mount them either
"by path" or "by UUID".
6.14.2 Booting (Expert)
#System z: This module cannot be used to configure the boot loader (zipl) on the
IBM System z platforms. ◄
YaST proposes a boot configuration for your system. Other operating systems found
on your computer, such as Microsoft Windows or other Linux installations, will automatically be detected and added to the boot loader. However, SUSE Linux Enterprise
Server will be booted by default. Normally, you can leave these settings unchanged.
If you need a custom setup, modify the proposal for your system. For information,
see Section “Configuring the Boot Loader with YaST” (Chapter 11, The Boot Loader
GRUB, ↑Administration Guide).
6.14.3 Software (Overview)
SUSE Linux Enterprise Server contains a number of software patterns for various application purposes. Click Software to start the pattern selection and modify the installation scope according to your needs. Select your pattern from the list and see a
pattern description in the right part of the window. Each pattern contains a number
of software packages needed for specific functions (e.g. Web and LAMP server or a
print server). For a more detailed selection based on software packages to install, select Details to switch to the YaST Software Manager.
You can also install additional software packages or remove software packages from
your system at any later time with the YaST Software Manager. For more information, refer to Chapter 9, Installing or Removing Software (page 195).
116
Deployment Guide
Figure 6.9: Software Selection and System Tasks
NOTE: Default Desktop
The default desktop of SUSE Linux Enterprise Server is GNOME. To install
KDE, click Software and select KDE Desktop Environment from Graphical
Environment.
6.14.4 Language (Overview)
Here you can change the system Language you defined in the first step of the installation. It is also possible to add additional languages. To adjust the system language settings, select Language. Select a language from the list. The primary language is used
as the system language. You can also adapt keyboard layout and time zone to the primary language if the current settings differ. Details lets you modify language settings
for the user root, set UTF-8 support, or further specify the language (e.g. select
South African English).
Choose secondary languages to be able to switch to one of these languages at any time
without having to install additional packages. For more information, see Chapter 13,
Changing Language and Country Settings with YaST (page 237).
Installation with YaST
117
6.14.5 Add-On Products (Expert)
If you added a source for an add-on media earlier, it appears here. Add, remove, or
modify add-on products here, if needed.This is the same configuration dialog as discussed earlier in Section 6.11.1, “Add-On Products” (page 110).
6.14.6 Keyboard Layout (Expert)
To change the keyboard layout, select Keyboard Layout. By default, the layout corresponds to the language chosen for installation. Select the keyboard layout from the
list. Use the Test field at the bottom of the dialog to check if you can enter special
characters of that layout correctly. Options to fine-tune various settings are available
under Expert Mode. When finished, click Accept to return to the installation summary.
6.14.7 Time Zone (Expert)
Adjust time zone and clock settings here. Provided a network is configured, you can
also set up a Network Time Protocol (NTP) client that automatically synchronizes
your computer with a time server. This is the same configuration as shown earlier in
Section 6.12, “Clock and Time Zone” (page 111).
6.14.8 Default Runlevel (Expert)
SUSE Linux Enterprise Server can boot to different runlevels. Normally, there
should be no need to change anything here, but if necessary set the default runlevel with this dialog. Refer to Section “Configuring System Services (Runlevel) with
YaST” (Chapter 10, Booting and Configuring a Linux System, ↑Administration Guide)
for more information about runlevel configuration.
6.14.9 System (Expert)
This dialog presents all the hardware information YaST could obtain about your computer. When called, the hardware detection routine is started. Depending on your system, this may take some time. Select any item in the list and click Details to see detailed information about the selected item. Use Save to File to save a detailed list to either the local file system or a floppy. Advanced users can also change the PCI ID setup and Kernel Settings by choosing Kernel Settings.
118
Deployment Guide
6.14.10 Kdump (Expert)
Using kdump, you can save a dump of the kernel (in case of a crash) to analyze what
went wrong. Use this dialog to enable and configure kdump. Find detailed information at Chapter 18, kexec and kdump (↑System Analysis and Tuning Guide).
6.15 Performing the Installation
After configuring all installation settings, click Install in the Installation Settings window to start the installation. Some software may require a license confirmation. If
your software selection includes such software, license confirmation dialogs are displayed. Click Accept to install the software package. When not agreeing to the license,
click I Disagree and the software package will not be installed. In the dialog that follows, confirm with Install again.
The installation usually takes between 15 and 30 minutes, depending on the system
performance and the selected software scope. After having prepared the hard disk and
having saved and restored the user settings, the software installation starts.
After the software installation has completed, the basic system is set up. Among others, “Finishing the Basic Installation” includes installing the boot manager, initializing
fonts and more. Next YaST boots into the new Linux system to start the system configuration.
TIP: Existing SSH Host Keys
If you install SUSE Linux Enterprise Server on a machine with existing Linux
installations, the installation routine automatically imports the SSH host key
with the most recent access time from an existing installation.
6.15.1 IBM System z: IPLing the Installed
System
In most cases, YaST automatically reboots into the installed system on the IBM System z platform. Known exceptions to this are installations wherein the boot loader resides on an FCP device in environments with LPAR on a machine older than z9 or
with z/VM older than release 5.3. The boot loader gets written to the device that holds
Installation with YaST
119
the /boot directory. If /boot is not on a separate partition, it is on the same partition as the root file system /.
In cases where an automatic reboot is not possible, YaST will show a dialog box containing information about from which device to do an IPL. Accept the shutdown option and perform an IPL after the shutdown. The procedure varies according to the
type of installation:
LPAR Installation
In the IBM System z HMC, select Load, select Clear, then enter the loading address (the device address of the device holding the /boot directory with the
boot loader). If using a ZFCP disk as the boot device, choose Load from SCSI and
specify the load address of your FCP adapter as well as WWPN and LUN of the
boot device. Now start the loading process.
z/VM Installation
Log in to the VM guest (see Example 4.5, “Configuration of a z/VM
Directory” (page 55) for the configuration) as LINUX1 and proceed to IPL the
installed system:
IPL 151 CLEAR
151 is an example address of the DASD boot device, replace this value with the
correct address.
If using a ZFCP disk as the boot device, specify both the ZFCP WWPN and
LUN of the boot device before initiating the IPL. The parameter length is limited
to eight characters. Longer numbers must be separated by spaces:
SET LOADDEV PORT 50050763 00C590A9 LUN 50010000 00000000
Finally, initiate the IPL:
IPL FC00
FC00 is an example address of the ZFCP adapter, replace this value with the correct address.
6.15.2 IBM System z: Connecting to the
Installed System
After IPLing the installed system, establish a connection with it to complete the installation. The steps involved in this vary depending on the type of connection used at the
outset.
120
Deployment Guide
6.15.2.1 Using VNC to Connect
A message in the 3270 terminal asks you to connect to the Linux system using a VNC
client. This message is easily missed, however, because it is mixed with kernel messages and the terminal process might quit before you become aware of the message. If
nothing happens for five minutes, try to initiate a connection to the Linux system using a VNC viewer.
If you connect using a Java-capable browser, enter the complete URL, consisting of
the IP address of the installed system along with the port number, in the following
fashion:
http://<IP of installed system>:5801/
6.15.2.2 Using X to Connect
When IPLing the installed system, make sure that the X server used for the first phase
of the installation is up and still available before booting from the DASD. YaST opens
on this X server to finish the installation. Complications may arise if the system is
booted up but unable to connect to the X server in a timely fashion.
6.15.2.3 Using SSH to Connect
IMPORTANT: IBM System z: Connecting from a Linux or UNIX
System
Start SSH in an xterm. Other terminal emulators lack complete support for
the text-based interface of YaST.
A message in the 3270 terminal asks you to connect to the Linux system with an SSH
client. This message is easily missed, however, because it is mixed with kernel messages and the terminal process might quit before you become aware of the message.
Once the message appears, use SSH to log in to the Linux system as root. If the connection is denied or times out, wait for the login timeout to expire, then try again (this
time may vary depending on server settings).
When the connection is established, execute the command /usr/lib/YaST2/
startup/YaST2.ssh. Just executing the command yast does not suffice in this
case.
Installation with YaST
121
YaST then begins completing the installation of the remaining packages and creating
an initial system configuration.
6.16 Configuration of the Installed
System
The system is now installed, but not yet configured for use. The hardware, the network and other services are not yet set up.
6.16.1 System Configuration
Having rebooted, the system starts the manual configuration. If the configuration fails
at one of the steps of this stage, it restarts and continues from the last successful step.
6.16.1.1 Password for the System Administrator
“root”
root is the name of the superuser, the administrator of the system. Unlike regular
users, who may or may not have permission to execute administrative commands on
the system, root has unlimited command capacity, for instance changing the system configuration, installing programs, and setting up new hardware. If users forget
their passwords or have other problems with the system, root can help. The root
account should only be used for system administration, maintenance, and repair. Logging in as root for daily work is rather risky: a single mistake could lead to the irretrievable loss of system files.
For verification purposes, the password for root must be entered twice. Do not forget the root password. Once entered, this password cannot be retrieved.
When typing passwords, the characters are replaced by dots, so you do not see the
string you are typing. If you are unsure whether you have typed the correct string, use
the Test Keyboard Layout field for testing purposes.
SUSE Linux Enterprise Server can use the DES, MD5, or Blowfish encryption algorithms for passwords. The default encryption type is Blowfish. To change the encryption type, click Expert Options > Encryption Type and select the new type.
122
Deployment Guide
The root can be changed any time later in the installed system. To do so run YaST
and start Security and Users > User and Group Management.
6.16.1.2 Hostname and Domain Name
The hostname is the computer's name in the network. The domain name is the name
of the network. A hostname and domain are proposed by default. If your system is
part of a network, the hostname has to be unique in this network, whereas the domain
name has to be common to all hosts on the network.
In many networks, the system receives its name over DHCP. In this case it is not necessary to modify the proposed hostname and domain name. Select Change Hostname
via DHCP instead. To be able to access your system using this hostname, even when it
is not connected to the network, select Assign Hostname to Loopback IP. Do not enable
this option when your machine provides network services. If you often change networks without restarting the desktop environment (e.g. when switching between different WLANs), do not enable this option either, because the desktop system may get
confused when the hostname in /etc/hosts changes.
To change hostname settings at any time after installation, use YaST Network Devices
> Network Settings. For more information, see Section “Configuring the Network Card
with YaST” (Chapter 22, Basic Networking, ↑Administration Guide).
6.16.1.3 Network Configuration
TIP: IBM System z: Network Configuration
For the IBM System z platforms, a working network connection is needed at
installation time to connect to the target system, the installation source, and
the YaST terminal controlling the process. The steps to set up the network
are discussed in Section 4.2.5, “Network Configuration” (page 61). The IBM
System z platforms only support the types of network interfaces mentioned
there (OSA Ethernet, OSA Gigabit Ethernet, OSA Express Fast Ethernet, Escon, and IUCV). The YaST dialog simply displays the interface with its settings as already configured. Just confirm this dialog to continue.
By default, Traditional Method without NetworkManager Applet is enabled. If desired,
you can also use NetworkManager to manage all your network devices. However, the
traditional method is the preferred option for server solutions. Find detailed informaInstallation with YaST
123
tion about NetworkManager in Chapter 27, Using NetworkManager (↑Administration
Guide).
The network can also be configured after the system installation has been completed.
If you skip it now, your system is left offline unable to retrieve any available updates.
To configure your network connection later, select Skip Configuration and click Next.
The following network settings can be configured in this step:
General Network Settings
Enable or disable the use of NetworkManager as described above. Also change
the IPv6 support here. By default the IPv6 support is enabled. To disable it, click
Disable IPv6. For more information about IPv6, see Section “IPv6—The Next
Generation Internet” (Chapter 22, Basic Networking, ↑Administration Guide).
Firewall
By default SuSEFirewall2 is enabled on all configured network interfaces. To
globally disable the firewall for this computer, click on Disable. If the firewall is
enabled, you may Open the SSH port in order to allow remote connections via secure shell. To open the detailed firewall configuration dialog, click on Firewall.
See Section “Configuring the Firewall with YaST” (Chapter 15, Masquerading
and Firewalls, ↑Security Guide) for detailed information.
Network Interfaces
All network cards detected by YaST are listed here. If you have already set up
a network connection during the installation (as described in Section 6.11.1.1,
“Network Setup” (page 111)) the card used for this connection is listed as Configured. A click on Network Interfaces opens the Network Settings dialog, where
you can change existing configurations, set up networks cards not configured yet,
or add and configure additional cards.
DSL Connections, ISDN Adapters, and Modems
If your computer is equipped with an internal DSL modem, an internal ADSL
Fritz Card, an ISDN card or a modem, clicking on the respective headline opens
the configuration dialog. Refer to Chapter 11, Accessing the Internet (page 217)
for further information.
VNC Remote Administration
To enable remote administration of your machine via VNC, click VNC Remote
Administration. Choose Allow Remote Administration in the following dialog and
adjust your firewall settings accordingly.
124
Deployment Guide
Proxy
If you have a proxy server controlling the Internet access in your network, configure the proxy URLs and authentication details in this dialog.
TIP: Resetting the Network Configuration to the Default Values
Reset the network settings to the original proposed values by clicking
Change > Reset to Defaults. This discards any changes made.
Test Internet Connection
After having configured a network connection, you can test it. For this purpose, YaST
establishes a connection to the SUSE Linux Enterprise Server server and downloads
the latest release notes. Read them at the end of the installation process. A successful
test is also a prerequisite for the automatic addition of the default repositories and for
updating online.
If you have multiple network interfaces, verify that the desired card is used to connect
to the Internet. If not, click Change Device.
To start the test, select Yes, Test Connection to the Internet and click Next. In the following dialog, view the progress of the test and the results. Detailed information about
the test process is available via View Logs. If the test fails, click Back to return to the
network configuration to correct your entries.
Proceed with Next. If the test was successful, the official software repositories for
SUSE Linux Enterprise Server and the update repository will be configured. Downloading the repository data for the first time may take some time.
If you do not want to test the connection at this point, select No, Skip This Test then
Next. This also skips downloading the release notes, configuring the customer center
and updating online. These steps can be performed any time after the system has been
initially configured.
6.16.1.4 Novell Customer Center Configuration
To get technical support and product updates, you need to register and activate your
product with the Novell Customer Center. The Novell Customer Center Configuration
provides assistance for doing so. Find detailed information about Novell Customer
Center at http://www.novell.com/documentation/ncc/.
Installation with YaST
125
If you are offline or want to skip this step, select Configure Later. This also skips
SUSE Linux Enterprise Server's online update.
In Include for Convenience, select whether to send unsolicited additional information,
such as your Hardware Profile or Optional Information when registering. This simplifies the registration process. Click on Details to get in-depth information about how
the data will be collected. In order to obtain information about which data will be sent
for your specific product, the Novell server will be connected. Upon this initial connect no data other than the ID of your product will be sent to the Novell servers.
In order to become entitled for support, make sure to check Registration Code. You
will be prompted to enter the code when proceeding with Next. Find more information about the technical support at http://www.suse.com/support/pro​
grams/.
NOTE: Data Privacy
No information is passed to anyone outside Novell/SUSE. The data is used
for statistical purposes and to enhance your convenience regarding driver support and your Web account. Find a link to the detailed privacy policy by clicking on Details. View the information transmitted in the log file at /
root/.suse_register.log.
Apart from activating and registering your product, this module also adds the official
update repositories to your configuration. These repositories provide fixes for known
bugs or security issues which can be installed via an online update.
To keep your repositories valid, select Regularly Synchronize with Customer Center.
This option checks your repositories and adds newly available catalogs or removes obsolete ones. It does not affect manually-added repositories.
Proceed with Next. A connection with the Novell server is established. Follow the onscreen instructions to finish the registration.
TIP: Re-registering an Installed System with a Different Registration
Code
When you register a system in Novell Customer Center, registration data is
stored locally and in the Novell Customer Center database. Although it is normally not necessary, there are corner cases which may require you to re-reg126
Deployment Guide
ister an already installed machine with a different registration code. To do so,
proceed with the following steps on the installed system:
1. Enter the following command as user root to delete the installation data
on the local machine:
suse_register.pl --erase-local-regdata
2. Next you need to remove the registered system from the Novell Customer
Center database. Go to http://www.suse.com/ in a browser and click
Support > Customer Center. Log in and navigate to My Systems > System.
Select the system and remove it by clicking on the dash sign in the bottom
bar of the table.
3. Now you can re-register the machine with either suse-register or the
YaST module Online Update Configuration.
Local Registration Server
If your organization provides a local registration server instead of using the Novell
Customer Center, you need to specify the server's URL. Client and server communicate solely via HTTPS protocol, therefore you also need to enter a path to the server's
certificate if the certificate was not issued by a certificate authority. Open the dialog
with Advanced > Local Registration Server
Registration Server
URL of the registration server. The URL has a fixed format https://FQN/
center/regsvc/ FQN has to be full qualified hostname of the registration
server. Example:
https://smt.example.com/center/regsvc/
Server CA certificate location
Location of the registration server's certificate. Specify one of the following locations:
URL
Remote location (http, https or ftp) from which the certificate can be downloaded. Example:
http://smt.example.com/smt-ca.crt
Installation with YaST
127
Floppy
Specifies a location on a floppy. The floppy has to be inserted before proceeding. The value has to start with the string floppy followed by the path
to the certificate. Example:
floppy/smt/smt-ca.crt
local path
Absolute path to the certificate on the local machine. Example:
/data/inst/smt/smt-ca.cert
Interactive
Use ask to open a pop-up menu where you can specify the path to the certificate. Do not use this option with AutoYaST. Example
ask
Deactivate certificate installation
Use done if either the certificate will be installed by an add-on product, or
if you are using a certificate issued by an official certificate authority. Example:
done
6.16.1.5 Online Update
If an Internet connection has been established, and updates are available, select
whether to perform a YaST online update. If there are any patched packages available
on the servers, download and install them now to fix known bugs or security issues.
For detailed instructions see Chapter 1, YaST Online Update (↑Administration Guide).
Directives on how to perform an online update in the installed system are available at
Section 9.4, “Keeping the System Up-to-date” (page 206) or Chapter 1, YaST Online Update (↑Administration Guide). This step is skipped if no updates are available or
no Internet connection has been established. Patches fixing security issues and recommended patches applying to your installation are automatically preselected. Click Accept to install them and Next to proceed with the system configuration.
IMPORTANT: Downloading Software Updates
The download of updates might take quite some time, depending on the
bandwidth of the Internet connection and the size of the update files. In case
the patch system itself is updated, the online update will restart and down128
Deployment Guide
load more patches after the restart. If the kernel was updated, the system will
reboot before completing the configuration.
6.16.1.6 Services Configuration
After testing the Internet connection and downloading the first updates, a dialog opens
in which to enable and configure three network services.
CA Management
The purpose of a CA (certificate authority) is to guarantee a trust relationship
among all network services communicating with each other. Without a CA, you
can secure server communications with SSL and TLS separately for each individual service. By default, a CA is created and enabled during the installation. Find
details about the creation of a CA with YaST in Chapter 17, Managing X.509
Certification (↑Security Guide).
OpenLDAP Server
You can run an LDAP service on your host to have a central facility manage a
range of configuration files. Typically, an LDAP server handles user account data, but with SUSE Linux Enterprise Server it can also be used for mail, DHCP,
and DNS data. By default, an LDAP server is set up during the installation. If you
decide against the use of an LDAP server, the YaST mail server module does not
work because it depends on LDAP functionality. However, you can still set up a
mail server on your system with the help of the Mail Transfer Agent module. Find
details about LDAP and its configuration with YaST in Chapter 4, LDAP—A Directory Service (↑Security Guide).
Services
The CIM (Common Information Model) Server is started by default. Click Disable to prevent the server automatically stating at boot time. For more information on CIM services refer to Chapter 34, Web Based Enterprise Management Using SFCB (↑Administration Guide).
If preferred, you can skip this configuration proposal for now. After the installation is
finished, configure and start the same services with the help of YaST.
TIP: Resetting the Service Configuration to Defaults
Restore the defaults by clicking Change > Reset to Defaults. This discards
any changes made.
Installation with YaST
129
6.16.1.7 User Authentication Method
If network access was configured successfully during the previous steps of the installation, you can now choose from several user management options. If a network connection has not been configured, create local user accounts. You may also, if present,
import users from a previous installation. Also change the password encryption type
in this dialog.
You can also add additional user accounts or change the user authentication method
in the installed system. For detailed information about user management, see Chapter 12, Managing Users with YaST (page 221).
The default authentication method is Local (/etc/passwd). If a former version of SUSE
Linux Enterprise Server or another system using /etc/passwd is detected, you
may import local users. To do so, check Read User Data from a Previous Installation
and click Choose. In the next dialog, select the users to import and finish with OK.
Manually enter local users by clicking Next. The New Local User dialog opens. After entering the first name and last name, either accept the proposal or specify a new
Username that will be used to log in. Finally, enter a password for the user. Reenter it
for confirmation (to ensure that you did not type something else by mistake). To provide effective security, a password should be between five and eight characters long.
The maximum length for a password is 72 characters. However, if no special security modules are loaded, only the first eight characters are used to discern the password.
Passwords are case-sensitive. Special characters (7-bit ASCII) and the digits 0 to 9 are
allowed. Other special characters like umlauts or accented characters are not allowed.
Passwords you enter are checked for weakness. When entering a password that is easy
to guess, such as a dictionary word or a name, you will see a warning. It is a good security practice to use strong passwords.
Two additional options are available:
Receive System Mail
Checking this box sends messages created by the system services to the user.
These are usually only sent to root, the system administrator. This option is useful for the most frequently used account, because it is highly recommended to log
in as root only in special cases.
The mails sent by system services are stored in the local mailbox /var/spool/
mail/username, where username is the login name of the selected user. To
130
Deployment Guide
read e-mails after installation, you can use any e-mail client, for example KMail
or Evolution.
Automatic Login
This option automatically logs the current user in to the system on start-up. This is
mainly useful if the computer is operated by only one user. For automatic login to
work, the option must be explicitly enabled.
WARNING: Automatic Login
With automatic login enabled, the system boots straight to your desktop with
no authentication at all. If you store sensitive data on your system, you should
not enable this option if the computer can also be accessed by others.
Enter more users by calling the User Management module described in Chapter 12,
Managing Users with YaST (page 221).
When using a network server for user authentication, access to the following services
can be configured:
LDAP
Users are administered centrally on an LDAP server for all systems in the network. More information is available in Section “Configuring an LDAP Client
with YaST” (Chapter 4, LDAP—A Directory Service, ↑Security Guide).
NIS
Users are administered centrally on a NIS server for all systems in the network.
See Section “Configuring NIS Clients” (Chapter 3, Using NIS, ↑Security Guide)
for more information.
Windows Domain
SMB authentication is often used in mixed Linux and Windows networks.
Detailed information is available in Section “Samba Server in the Network
with Active Directory” (Chapter 28, Samba, ↑Administration Guide) and
Section “Configuring a Linux Client for Active Directory” (Chapter 5, Active Directory Support, ↑Security Guide).
Along with user administration via LDAP and NIS, you can use Kerberos authentication. To use it, select Set Up Kerberos Authentication. For more information on Kerberos, refer to Chapter 6, Network Authentication with Kerberos (↑Security Guide).
Installation with YaST
131
6.16.1.8 Release Notes
After completing the user authentication setup, YaST displays the release notes. Reading them is recommended, because they contain important up-to-date information
which was not available when the manuals were printed. If you successfully tested the
Internet connection, read the most recent version of the release notes, as fetched from
SUSE Linux Enterprise Server's servers. Use Miscellaneous > Release Notes in YaST
or start the SUSE Help Center to view the release notes after installation.
6.16.1.9 Hardware Configuration
At the end of the installation, YaST opens a dialog for the configuration of Graphics
Cards Printer and Sound. Click the individual components to start the hardware configuration. For the most part, YaST detects and configures the devices automatically.
TIP: IBM System z: Hardware Configuration
On the IBM System z, there is no display that would be supported by XFree.
Accordingly, you do not find a Graphics Cards entry on these systems.
You can skip any peripheral devices and configure them later, as described in Chapter 8, Setting Up Hardware Components with YaST (page 179). To skip the configuration, select Skip Configuration and click Next.
However, when setting up a desktop system you should configure the graphics card
right away. Although the display settings as configured by YaST should be generally
acceptable, most users have very strong preferences as far as resolution, color depth,
and other graphics features are concerned. To change these settings, select the respective item and set the values as desired.
TIP: Resetting Hardware Configuration to the Default Values
You can cancel any changes to the hardware configuration by clicking
Change > Reset to Defaults. YaST then shows the original proposal again.
6.16.1.10 Installation Completed
After a successful installation, YaST shows the Installation Completed dialog. In this
dialog, select whether to clone your newly installed system for AutoYaST. To clone
132
Deployment Guide
your system, select Clone This System for AutoYaST. The profile of the current system
is stored in /root/autoyast.xml. Cloning is selected by default.
AutoYaST is a system for installing one or more SUSE Linux Enterprise Server systems automatically without user intervention. AutoYaST installations are performed
using a control file with installation and configuration data.For detailed information,
refer to Chapter 21, Automated Installation (page 343). Finish the installation of
SUSE Linux Enterprise Server with Finish in the final dialog.
6.17 Graphical Login
TIP: IBM System z: No Graphical Login
The graphical login is not available on IBM System z platforms.
SUSE Linux Enterprise Server is now fully installed and configured. Unless you enabled the automatic login function or customized the default runlevel, you should see
the graphical login on your screen in which to enter a username and password to log in
to the system. On single user systems with automatic login enabled, the desktop starts
automatically.
Installation with YaST
133
7
Updating SUSE Linux
Enterprise
SUSE® Linux Enterprise (SLE) provides the option of updating an existing system to
the new version without completely reinstalling it. No new installation is needed. Existing data, such as home directories and system configuration, is kept intact. During
the life-cycle of the product, you can apply Service Packs to increase system security, correct software defects and get access to new features. Install from a local CD or
DVD drive or from a central network installation source.
7.1 Terminology
This chapter uses several terms. In order to understand the information, read the definitions below:
Backporting
Backporting is the act of adapting specific changes from a newer version of software and applying it to an older version. The most commonly used case is fixing
security holes in older software components. Usually it is also part of a maintenance model to supply enhancements or (less commonly) new features.
Deltarpm
A deltarpm consists only of the binary diff between two defined versions of a
package, and therefore has the smallest download size. Before being installed, the
full RPM package is rebuilt on the local machine.
Updating SUSE Linux Enterprise
135
Downstream
A metaphor of how software is developed in the open source world (compare it
with upstream). The term downstream refers to people or organisations like SUSE
who integrate the source code from upstream with other software to build a distribution which is then used by end users. Thus, the software flows downstream
from its developers via the integrators to the end users.
Online Migration
Updating to a Service Pack (SP) by using the online update tools (rather than the
installation media) to install the respective patches. It updates all packages of the
installed system to the latest state—including updates—of SP3 plus SP2 updates.
Package
A package is a compressed file in rpm format that contains all files for a particular program, including optional components like configuration, examples, and
documentation.
Patch
A patch consists of one or more packages and may be applied by means of
deltarpms. It may also introduce dependencies to packages that are not installed
yet.
Service Packs (SP)
Combines several patches into a form which is easy to install or deploy. Service
packs are numbered and usually contain security fixes, updates, upgrades, or enhancements of programs.
Upstream
A metaphor of how software is developed in the open source world (compare
it with downstream). The term upstream refers to the original project, author or
maintainer of a software that is distributed as source code. Feedback, patches,
feature enhancements, or other improvements flow from end users or contributors to upstream developers. They decide if the request will be integrated or rejected.
If the project members decide to integrate the request, it will show up in newer
versions of the software. An accepted request will benefit all parties involved.
If a request is not accepted, it may be for different reasons. Either it is in a state
which is not compliant with the project's guidelines, it is invalid, it is already integrated, or it is not in the interest or roadmap of the project. An unaccepted re136
Deployment Guide
quest makes it harder for upstream developers as they have to keep their patches
in sync with the upstream code. This practice is generally avoided, but sometimes
it is still needed.
Update
Installation of a newer minor version of a package.
Upgrade
Installation of a newer major version of a package or distribution, which brings
new features.
7.2 The SUSE Linux Enterprise 11
Maintenance Model
The SUSE Linux Enterprise 11 Maintenance Model combines flexibility and control
of your service packs. It offers the following benefits:
• Makes service packs more lightweight and easier to test and deploy.
• Allows staying with older versions, but with support for the full system.
• Answers market needs in between service packs by selective enhancements and allows more updates in the general update repository. By selecting the enhancements,
it mitigates longer periods between service packs.
7.2.1 Background Information
Over the last few years, with a clear desire for improvements based on customer feedback, SUSE has implemented various changes regarding the way we deliver updates to
our users:
• In SLES 9, there was only one update repository that collected all the updates; the
most recent release update was the only one to be supported.
• Starting with SLES 10 SP1, the concept of a “SP-specific repository” was introduced. This means that all the updates for a specific service pack are delivered in
Updating SUSE Linux Enterprise
137
one specific repository. Once users migrate to a newer service pack, they lose access to the preceding repositories if they registered directly at the Novell Customer
Center. Users of SMT or SUSE Manager were able and are still able to subscribe
to any SP channel freely. The main reason for this change was the concept of a 6month overlap period (n-1 service pack support) to allow validation of the released
service pack and a window of migration for customers, whereby they would continued to be maintained and supported fully within the old SP.
• SLES 11 GA and SLES 11 SP1 followed the SLES 10 model. With SLES 11 SP2
we introduced a new repository model, consisting of the following:
i. SLES 11 SP1 Updates repository remained subscribed. All updates that were also applicable to SP2 were also or only released into the SP1 Updates repository.
This means that all the updates that don't break the ABI and API compatibility
continued to be delivered here.
ii. SLES 11 SP2 Updates repository includes only the latest and any innovative updates that can't be delivered to the SP1 Updates repository (for various reasons).
In addition to this, we introduced a core repository, which provided a “gap” for
packages that were neither released into the SP1 nor the SP2 Updates repository.
iii.SLES 11 SP4 will have a simplified channel model. All updates will be shipped
via an update channel special. Only in case of online migration, additional channels will be made available on the machine. Any custom repositories stay untouched.
Figure 7.1, “Maintenance Delivery Evolution (also applies to SLED)” (page 139)
depicts some of the mentioned aspects above.
138
Deployment Guide
Figure 7.1: Maintenance Delivery Evolution (also applies to SLED)
SLES 9
GA
SLES 10
GA
SP1
SP2
SP3
Flexibility
Control
SP1
SP2
SP3
6 month overlap
SLES 11
GA
Flexibility
and
Control
SP1
SP2
SP3
Timeline
Our products have a 10-year life-cycle: 10 years general support and 3 years extended support. Major releases are made every 4 years and service packs every 18 months.
The Long Term Service Pack Support is an extended window or extended major release life-cycle (see Figure 7.2, “Long Term Service Pack Support” (page 139)).
Figure 7.2: Long Term Service Pack Support
Extended Support
General Support
Year 1
Year 2
Year 3
Year 4
Year 5
Year 6
Year 7
Year 8
Year 9 Year 10
GA
SP1
Long Term Service Support
SP2
Long Term Service Support
SP3
Long Term Service Support
SP4
Long Term Service Support
The Long Term Service Pack Support requires active subscription, either standard or
priority. It does not affect L1 or L2 subscription terms. Security updates are handled
Updating SUSE Linux Enterprise
139
“proactively”: these are any non-user driven critical vulnerabilities, local root exploits
in Kernel or other root exploits directly executable without user interaction.
7.2.2 Support Levels
The range for extended support levels starts from year 8 and ends in year 10. These
contain continued L3 engineering level diagnosis and reactive critical bug fixes. These
support levels proactively update trivial local root exploits in Kernel or other root exploits directly executable without user interaction. Furthermore they support existing
workloads, software stacks, and hardware with limited package exclusion list. Find an
overview in Table 7.1, “Security Updates and Bug Fixes” (page 140).
Table 7.1: Security Updates and Bug Fixes
140
— General Support —
Extended Support
Topic
Current
SP
SP
(n-1) 6
months
SP (n-1)
with
LTSS
Year 6
& 7 with
LTSS
Year
8, 9, 10
with
LTSS
L1/L2
Technical Services
✓
✓
✓
✓
✓
Proactive
Maintenance
✓
✓
✓
Driver Updates via
PLDP
✓
✓
✓
Deployment Guide
— General Support —
Extended Support
Topic
Current
SP
SP
(n-1) 6
months
SP (n-1)
with
LTSS
Year 6
& 7 with
LTSS
Year
8, 9, 10
with
LTSS
Proactive
Security
Updates
✓
✓
✓
✓
L3 Engineering
Support
✓
✓
✓
✓
✓
Backports
available
✓
✓
✓
✓
7.2.3 Channel Model
With the former maintenance model, SUSE Linux Enterprise Server, had two channels assigned: SLES11-SPx-Pool and SLES11-SPx-Updates. During an online migration to SPx+1 these channels were temporary replaced by SLES11-SPxOnline.
With SUSE Linux Enterprise SP 2 the channel layout has changed to support the benefits of the new maintenance model. Table 7.2, “Channel Layout for SUSE Linux Enterprise 11 SP1 to SP4” (page 141) contains a list of all channels from SP1 to SP3.
Table 7.2: Channel Layout for SUSE Linux Enterprise 11 SP1 to SP4
Type
SLES
SLED
Required
Channels
SP1
SP1
SLES11-SP1-Pool
SLED11-SP1-Pool
Updating SUSE Linux Enterprise
141
Type
Optional
Channels
142
Deployment Guide
SLES
SLED
SLES11-SP1-Updates
SLED11-SP1-Updates
SP2
SP2
SLES11-SP1-Pool
SLES11-SP1-Updates
SLES11-SP2-Core
SLES11-SP2-Updates
SLED11-SP1-Pool
SLED11-SP1-Updates
SLED11-SP2-Core
SLED11-SP2-Updates
SP3
SP3
SLES11-SP3-Pool
SLES11-SP3-Updates
SLED11-SP3-Pool
SLED11-SP3-Updates
SP4
SP4
SLES11-SP4-Pool
SLES11-SP4-Updates
SLED11-SP4-Pool
SLED11-SP4-Updates
SP1
SP1
SLES11-SP1-Debuginfo-Pool
SLES11-SP1-Debuginfo-Updates
SLED11-SP1-Debuginfo-Pool
SLED11-SP1-Debuginfo-Updates
SP2
SP2
SLES11-SP2-Debuginfo-Core
SLES11-SP2-Debuginfo-Updates
SLES11-Extras
SLES11-SP2-Extension-Store
SLED11-SP2-Debuginfo-Core
SLED11-SP2-Debuginfo-Updates
SLED11-Extras
SLED11-SP2-Extension-Store
SP3
SP3
Type
Product-Specific
(Examples)
SLES
SLED
SLES11-SP3-Debuginfo-Core
SLES11-SP3-Debuginfo-Updates
SLES11-SP3-Extension-Store
SLES11-Extra
SLED11-SP3-Debuginfo-Core
SLED11-SP3-Debuginfo-Updates
SLED11-SP3-Extension-Store
SLED11-Extra
SP4
SP4
SLES11-SP4-Debuginfo-Pool
SLES11-SP4-Debuginfo-Updates
SLES11-Extra
SLES11-Security-Module
SLED11-SP4-Debuginfo-Pool
SLED11-SP4-Debuginfo-Updates
SLES11-WebYaST-SP2Pool
SLES11-WebYaST-SP2Updates
SLED11-MSI-Updates
Description of Required Channels
Core
A subset of the unpacked installation media, it only contains those packages that
are considered to be the “core” of SPx (approximately 30% of the package total).
The SP repositories only contain packages specific to a SP and its themes (for example, hardware enablement). Exists only in SP2.
Updates
Maintenance updates to packages in the corresponding Core or Pool repository.
Pool
Containing all binary RPMs from the installation media, plus pattern information
and support status metadata.
Updating SUSE Linux Enterprise
143
Description of Optional Channels
Debuginfo-Pool , Debuginfo-Updates
These channels contain static content. However, only the Debuginfo-Updates channel receives updates. Enable these channels if you need to install libraries with debug information in case of an issue.
Extension-Store
Not in use, yet. Supposed to contain packages for (future) add-on products. The
Extension Store channel will be removed starting with SLES 11 SP4.
LTSS-Updates
Maintenance updates to packages in the corresponding Pool repository for installations with Long Term Support Service (LTSS). This specific channels require an LTSS contract.
7.2.3.1 Origin of Packages
SUSE Linux Enterprise 11 SP3/SP4 With the installation of SP3 there are only two channels available: SLES11-SP3-Pool and SLES11-SP3-Updates. Any previous channels from SP2 are visible, but not enabled. These disabled channels are only
needed for users who have particular needs.
7.2.3.2 Working with Channels
On registration, the system receives channels from the Customer Center. The
channel names map to specific URIs in the customer center (see http://
scc.suse.com). To list all available channels on your system, use zypper as follows:
zypper repos -u
This gives you a list of all available channels on your system. Each channel is listed
by its alias, name and whether it is enabled and will be refreshed. The option -u gives
you also the URI from where it originated.
If you want to remove old channels (for example, from SP1), use zypper removerepo and the name(s) of the channel(s). For example, to remove the old SP1
and SP2 channels, use the following command:
zypper removerepo SLES11-SP1-Pool SLES11-SP1-Updates \
SLE11-SP1-Debuginfo-Pool SLE11-SP1-Debuginfo-Updates \
144
Deployment Guide
SLES11-SP2-Core SLES11-SP2-Updates \
SLE11-SP2-Debuginfo-Core SLES11-SP2-Extension-Store\
SLE11-SP2-Debuginfo-Updates
If you want to re-add some of your channels, log in to http://
www.novell.com/ncc and select from the menu My Products > Mirror Credentials. There you can see a list of URIs; Only channels from this list of products can be
added. For example, to add the SP2 Extension Store, use the following command (one
line, without the backslash):
zypper addrepo -n SLES11-SP2-Extension-Store \
https://nu.novell.com/repo/\$RCE/SLES11-SP2-Extension-Store/ \
nu_novell_com:SLES11-SP2-Extension-Store
7.3 Supported Upgrade Paths to
SLE SP4
Upgrading SLES 8, SLES 9 and NLD 9
There is no supported direct upgrade path from these versions. Instead it is recommended to perform a new installation.
Upgrading from SUSE Linux Enterprise 10 (any Service Pack)
There are supported ways to upgrade from SLES 10 GA and SPx or SLES 11 GA
and SP1 to SLES 11 SP3, which may require intermediate upgrade steps:
• SLES 10 GA -> SLES 10 SP1 -> SLES 10 SP2 -> SLES 10 SP3 ->
SLES 10 SP4 -> SLES 11 SP4, or
• SLES 11 GA -> SLES 11 SP1 -> SLES 11 SP2 -> SLES 11 SP3 -> SLES
11 SP4
Upgrade is supported from SLES 10 SP4 via bootable media (including PXE boot). For reference, see the releasenotes at https://
www.suse.com/releasenotes/x86_64/SUSE-SLES/11-SP4/
#Update.General.Sequence.
Attention for SLED users: some devel packages have been moved from the
SLED11-SP2 installation media to the SLED11-Extras repository. In order to avoid dependency conflicts during upgrade, enable this repository before
performing the actual upgrade. Execute yast2 repositories and enable
SLED11-Extras there. On SLES this extra step is not needed.
Updating SUSE Linux Enterprise
145
Upgrading from SUSE Linux Enterprise 11 GA
There is no supported direct migration path to SUSE Linux Enterprise 11 SP3.
An update has to be performed from SUSE Linux Enterprise 11 GA to SP1 first.
Proceed with Section 7.5, “Updating SLE 11 SP1 to SLE 11 SP2” (page 148)
and Section 7.6, “Updating SLE 11 SP2 to SLE 11 SP3” (page 157) afterwards.
Upgrading from SUSE Linux Enterprise 11 SP1
Refer to Section 7.5, “Updating SLE 11 SP1 to SLE 11 SP2” (page 148) for
details.
Upgrading from SUSE Linux Enterprise 11 SP2
Refer to Section 7.6, “Updating SLE 11 SP2 to SLE 11 SP3” (page 157) for
details.
Upgrading from SUSE Linux Enterprise 11 SP3
Refer to Section 7.7, “Updating SLE 11 SP3 to SLE 11 SP4” (page 162) for
details.
IMPORTANT: Cross-architecture Upgrades are not Supported
Cross-architecture upgrades (32-bit to 64-bit and 64-bit to 32-bit) are not
supported.
7.4 General Preparations for
Updating
Before starting the update procedure, make sure your system is properly prepared.
Among others, preparation involves backing up data and checking the release notes.
7.4.1 Make a Backup
Before updating, copy existing configuration files to a separate medium (such as tape
device, removable hard disk, etc.) to back up the data. This primarily applies to files
stored in /etc as well as some of the directories and files in /var and /opt. You
may also want to write the user data in /home (the HOME directories) to a backup
146
Deployment Guide
medium. Back up this data as root. Only root has read permissions for all local
files.
If you have selected Update an Existing System as the installation mode in YaST, you
can choose to do a (system) backup at a later point in time. You can choose to include
all modified files and files from the /etc/sysconfig directory. However, this
is not a complete backup, as all the other important directories mentioned above are
missing. Find the backup in the /var/adm/backup directory.
7.4.2 Partitioning and Disk Space
Before starting your update, make note of the root partition. The command df /
lists the device name of the root partition. In Example 7.1, “List with df h” (page 147), the root partition to write down is /dev/sda3 (mounted as /).
Example 7.1: List with df -h
Filesystem
Size Used Avail Use% Mounted on
/dev/sda3
74G
22G
53G 29% /
tmpfs
506M
0 506M
0% /dev/shm
/dev/sda5
116G 5.8G 111G
5% /home
/dev/sda1
44G
4G
40G
9% /data
Software tends to “grow” from version to version. Therefore, take a look at the available partition space with df before updating. If you suspect you are running short of
disk space, secure your data before updating and repartitioning your system. There is
no general rule regarding how much space each partition should have. Space requirements depend on your particular partitioning profile and the software selected.
7.4.3 Shut Down Virtual Machines
If your machine serves as a VM Host Server for KVM or Xen, make sure to properly
shut down all running VM Guests prior to the update. Otherwise you may not be able
to access the guests after the update.
7.4.4 Temporarily Disable Kernel
Multiversion Support
SUSE Linux Enterprise Server allows to install multiple Kernel versions by enabling
the respective settings in /etc/zypp/zypp.conf. Support for this feature needs
Updating SUSE Linux Enterprise
147
to be disabled for updating to a service pack. Once the update has successfully finished. multiversion support can be re-enabled again. To disable multiversion support,
comment the respective lines in /etc/zypp/zypp.conf. The result shoul look
like this:
#multiversion = provides:multiversion(kernel)
#multiversion.kernels = latest,running
To re-activate this feature after a successful update, remove the comment signs.
7.4.5 Version Specific Requirements
For version specific requirements, refer to the release notes coming with the update
product. In the release notes you can find additional information about upgrade procedures.
The current version of the release notes document containing the latest information
on SUSE Linux Enterprise Server can be read online at http://www.suse.com/
doc/sles11/#additional.
7.5 Updating SLE 11 SP1 to SLE 11
SP2
There are different supported ways for updating a SUSE Linux Enterprise 11 SP1 system to a Service Pack 2. You may either update by using the online update tools to install the respective patches (“Online Migration”) or update via the Service Pack installation media. Furthermore, updates can be performed via servers hosting Subscription
Management Tool or SUSE Manager.
An Online Migration is supported by the following tools:
• YaST wagon (graphical user interface)
• zypper (command line)
Alternatively, the full Service Pack media (DVD ISO image) can be downloaded.
Start the update process by booting from the physical Service Pack media or a network installation source.
148
Deployment Guide
7.5.1 Online Migration
Updating your system via online migration is done from within the running system.
You only need to reboot once, after the update is completed.
7.5.1.1 Requirements
In order to do an online update, the following requirements must be met. Make sure to
also read Section 7.4, “General Preparations for Updating” (page 146).
Product Registration
In order to be able to connect to the update channels, your product has to be registered. If it is not registered yet, either run the Novell Customer Center Configuration module in YaST or the suse_register command line tool to start the
registration.
Run an Online Update
Make sure the currently installed version has the latest patches installed. Run an
Online Update prior to the Online Migration. When using a graphical interface,
start the YaST Online Update or the updater applet. On the command line, run
the following commands (the last command needs to be run twice):
zypper ref -s
zypper update -t patch
zypper update -t patch
Reboot the system if needed.
See Chapter 1, YaST Online Update (↑Administration Guide) or Section “Updating
Software with Zypper” (Chapter 6, Managing Software with Command Line
Tools, ↑Administration Guide) for more information on the online update tools.
Third-Party Software
If your setup involves third-party software or add-on software, test this procedure
on another machine to make sure that the dependencies are not broken by the update.
IMPORTANT: Always Run a Complete Online Migration
The online migration always has to be completed from beginning to end. If an
online migration is interrupted in between, the system is corrupted beyond recovery.
Updating SUSE Linux Enterprise
149
7.5.1.2 Online Migration with YaST Wagon
If you have a SLES 11 SP1 system, find the needed steps at https://
www.suse.com/support/kb/doc.php?id=7011872. The following procedure applies to an online migration from SP1 to SP2.
NOTE: Registration Key
If add-ons are installed on your system, you might need to enter your registration key in order to update the system. Be prepared to have the key available.
1 When all requirements are met (see Section 7.5.1.1,
“Requirements” (page 149)), the update applet in the tray will display a message that a distribution upgrade is available. Click it to start YaST Wagon. Alternatively run /usr/sbin/wagon as root from the command line.
2 Confirm the Welcome dialog with Next.
3 If Wagon finds that the requirements are not met (required maintenance updates
are available but not yet installed) it will do an automatic self-update, which may
require a reboot. Follow the on-screen instructions.
4 Choose the update method in the following dialog. Choose Customer Center to
use the default setup (recommended).
Click Custom URL to manually choose the software channels used for the online migration. A list of channels will be displayed, providing the opportunity to
manually enable, disable, add, or delete channels. Add the SP2 update source(s).
This can either be the SP2 installation media or the SP2-Core and SP2-Updates channels. Click OK to return to the Update Method dialog.
If you want to review changes to the channel setup caused by the update process,
select Check Automatic Repository Changes.
Proceed with Next.
5 The system will be re-registered. During this process the SP2-Core and SP2Updates channels will be added to the system (see Section 7.2.3, “Channel
Model” (page 141) for more information). Confirm the addition of the channels.
150
Deployment Guide
6 If you have selected Check Automatic Repository Changes in the Update Method
dialog, the list of repositories will be displayed, providing the opportunity to
manually enable, disable, add, or delete channels. Proceed with OK when finished.
7 Choose the migration type:
Full migration
Updates all packages to the latest SP2 level.
Minimal Migration
Updates a minimal set of packages to the latest SP2 level.
Click Advanced to manually select the repositories used for upgrading.
Confirm your selection.
8 The Distribution Upgrade Settings screen opens, presenting a summary of the update configuration. The following sections are available:
Add-On Products
You may add SUSE Linux Enterprise Server add-on products or third-party
products here.
Update Options
Lists the actions that will be performed during the update. You can choose
whether to download all packages before installing them (default, recommended), or whether to download and install packages one by one.
Packages
Statistical overview of the update.
Backup
Set backup options.
Click Next and Start The Update to proceed.
IMPORTANT: Aborting the Online Migration
It is safe to abort the online migration on this screen prior to clicking
Start The Update and on all previous screens. Click Abort to leave the
update procedure and restore the system to the state it was in prior to
Updating SUSE Linux Enterprise
151
starting YaST wagon. Follow the instructions on screen and perform a
re-registration before leaving Wagon to remove the SP2 channels from
your system.
9 During the update procedure the following steps are executed:
9a Packages will be updated.
9b SuSEconfig will be run.
9c The system will be rebooted (press OK).
9d The newly updated system will be re-registered.
10 Your system has been successfully updated to Service Pack 2.
7.5.1.3 Online Migration with zypper
NOTE: Registration Key
If add-ons are installed on your system, you might need to enter your registration key in order to update the system. Be prepared to have the key available.
1 When all requirements are met (see Section 7.5.1.1,
“Requirements” (page 149)), the “products” needed for the online migration
have been added to /etc/products.d. Get a list of these products by running the following command:
zypper se -t product | grep -h -- "-migration" | cut -d'|' -f2
This command should at least return SUSE_SLES-SP2-migration. Depending on the scope of your installation, more products may be listed.
2 Install the migration products retrieved on the previous step with the command
zypper in -t product LIST_OF_PRODUCTS, for example
zypper in -t product SUSE_SLES-SP2-migration
3 Register the products installed in the previous step in order to get the respective
update channels:
152
Deployment Guide
suse_register -d 2 -L /root/.suse_register.log
4 Refresh repositories and services again:
zypper ref -s
5 Check the list of repositories you can retrieve with zypper lr. At least the
following repositories need to be Enabled:
• SLES11-SP1-Pool
• SLES11-SP1-Updates
• SLES11-SP2-Core
• SLES11-SP2-Updates
Depending on the scope of your installation, further repositories for add-on
products or extensions need to be enabled.
If one of these repositories is not enabled (the SP2 ones are not enabled by default when following this workflow), enable them with zypper modifyrepo --enable REPOSITORY ALIAS, for example:
zypper modifyrepo --enable SLES11-SP2-Core SLES11-SP2-Updates
If your setup contains third-party repositories that may not be compatible with
SP2, disable them with zypper modifyrepo --disable REPOSITORY ALIAS.
6 Now everything is in place to perform the distribution upgrade with zypper
dup --from REPO 1 --from REPO 2 .... Make sure to list all needed repositories with --from, for example:
zypper dup --from SLES11-SP2-Core --from SLES11-SP2-Updates
Confirm with y to start the upgrade.
7 Upon completion of the distribution upgrade from the previous step, a Minimal
Migration has been performed (a minimal set of packages has been updated to
the latest SP2 level). Skip this step if you do not intend to do a Full Migration.
In order to do a Full Migration (updates all packages to the latest SP2 level), run
the following command:
Updating SUSE Linux Enterprise
153
zypper update -t patch
8 Now that the upgrade to SP2 has been completed, you need to re-register your
product:
suse_register -d 2 -L /root/.suse_register.log
9 Last, reboot your system.
10 Your system has been successfully updated to Service Pack 2.
7.5.2 Updating by Booting from an
Installation Source
As an alternative to the Online Migration (see Section 7.5.1, “Online
Migration” (page 149) for details) you may also update your system by booting
from an installation source—either a DVD or a network installation source. The update will start like a normal installation.
Service Pack ISO images can be obtained from http://
download.novell.com/. Either burn it to a DVD or prepare a network installation source as described in Section 14.2, “Setting Up the Server Holding the Installation Sources” (page 254).
7.5.2.1 Updating from a Local DVD Drive
Before starting a new installation of a SUSE Linux Enterprise SP, ensure that all the
Service Pack installation media (DVDs) are available.
Procedure 7.1: Booting from the Service Pack Medium
1 Insert the first SUSE Linux Enterprise SP medium and boot your machine. A boot
screen similar to the original installation of SUSE Linux Enterprise 11 is displayed.
2 Select Installation and continue as outlined in the YaST installation instructions in
Chapter 6, Installation with YaST (page 93).
154
Deployment Guide
7.5.2.2 Updating from a Network Installation
Source
Before starting an update of a SUSE Linux Enterprise SP from a network installation
source, make sure that the following requirements are met:
• A network installation source is setup according to Section 14.2, “Setting Up the
Server Holding the Installation Sources” (page 254).
• A working network connection on both the installation server and the target machine that includes a name service, DHCP (optional, but needed for PXE boot), and
OpenSLP (optional) exists.
• The SUSE Linux Enterprise SP DVD 1 to boot the target system or a target system
set up for PXE boot according to Section 14.3.5, “Preparing the Target System for
PXE Boot” (page 273) exist.
Please refer to Chapter 14, Remote Installation (page 245) for in-depth information
on starting the upgrade from a remote server.
Network Installation—Boot from DVD
To perform a network installation using the SP DVD as the boot medium, proceed as
follows:
1 Insert the SUSE Linux Enterprise SP DVD 1 and boot your machine. A boot
screen similar to the original installation of SUSE Linux Enterprise 11 is displayed.
2 Select Installation to boot the SP Kernel then use F4 to select the type of network
installation source (FTP, HTTP, NFS, or SMB).
3 Provide the appropriate path information or select SLP as the installation source.
4 Select the appropriate installation server from those offered or use the boot options
prompt to provide the type of installation source and its actual location as in Section 6.1.2, “Installing from a Network Source without SLP” (page 96). YaST starts.
Finish the installation as outlined in Section 7.5.2.3, “The Update
Procedure” (page 156).
Updating SUSE Linux Enterprise
155
Network Installation—PXE Boot
To perform a network installation of a SUSE Linux Enterprise Service Pack via network, proceed as follows:
1 Adjust the setup of your DHCP server to provide the address information needed
for PXE boot according to Section 14.3.5, “Preparing the Target System for PXE
Boot” (page 273).
2 Set up a TFTP server to hold the boot image needed for PXE boot.
Use the first CD or DVD of your SUSE Linux Enterprise Service Pack
for this or follow the instructions in Section 14.3.2, “Setting Up a TFTP
Server” (page 265).
3 Prepare PXE boot and Wake-on-LAN on the target machine.
4 Initiate the boot of the target system and use VNC to remotely connect to
the installation routine running on this machine. See Section 14.5.1, “VNC
Installation” (page 278) for more information.
5 Finish the installation as outlined in Section 7.5.2.3, “The Update
Procedure” (page 156).
7.5.2.3 The Update Procedure
Once you have successfully booted from installation medium or the network, proceed
as follows to start the update:
1 On the Welcome screen choose Language and Keyboard and Accept the license
agreement. Proceed with Next.
2 In case you have booted from a physical medium, perform a Media Check to verify the integrity of the medium. Only skip this step if you have checked the medium
before.
3 On the Installation Mode screen, choose Update. Clicking on Next will start the update procedure.
156
Deployment Guide
7.5.3 Updating via Subscription
Management Tool (SMT)
As an alternative to downloading the updates for each single client system from the
Novell update server, it is possible to use the Subscription Management Tool (SMT)
for SUSE Linux Enterprise to mirror the updates to a local server.
This tool acts as Novell Customer Center proxy both for client registrations and as
software update repository. The SMT documentation at http://www.suse.com/
doc/smt11/ gives an overview of its features as well as instructions on how to implement it.
7.5.4 Updating via SUSE Manager
SUSE Manager is a server solution for providing updates, patches, and security fixes
for SUSE Linux Enterprise clients. It comes with a set of tools and a Web-based user
interface for management tasks.
The SUSE Manager documentation at http://www.suse.com/doc/
suse_manager/ gives an overview of its features as well as instructions on how to
set up server and clients.
7.6 Updating SLE 11 SP2 to SLE 11
SP3
Online Migration is supported by the following tools:
• YaST wagon (graphical user interface)
• zypper (command line)
If updating your system via online migration, the update is carried out while the system is running. You only need to reboot once, after the update is completed. It is still
possible to update with the following alternatives:
• Section 7.5.2, “Updating by Booting from an Installation Source” (page 154)
Updating SUSE Linux Enterprise
157
• Section 7.5.3, “Updating via Subscription Management Tool (SMT)” (page 157)
• Section 7.5.4, “Updating via SUSE Manager” (page 157)
7.6.1 Requirements
In order to do an online update, the following requirements must be met. Make sure to
also read Section 7.4, “General Preparations for Updating” (page 146).
Product Registration
In order to be able to connect to the update channels, your product has to be registered. If it is not registered yet, either run the Novell Customer Center Configuration module in YaST or the suse_register command line tool to start the
registration.
Run an Online Update
Make sure the currently installed version has the latest patches installed. Run an
Online Update prior to the Online Migration. When using a graphical interface,
start the YaST Online Update or the updater applet. On the command line, run
the following commands (the last command needs to be run twice):
zypper ref -s
zypper update -t patch
zypper update -t patch
Reboot the system if needed.
See Chapter 1, YaST Online Update (↑Administration Guide) or Section “Updating
Software with Zypper” (Chapter 6, Managing Software with Command Line
Tools, ↑Administration Guide) for more information on the online update tools.
Third-Party Software
If your setup involves third-party software or add-on software, test this procedure
on another machine to make sure that the dependencies are not broken by the update.
IMPORTANT: Always Run a Complete Online Migration
The online migration always has to be completed from beginning to end. If an
online migration is interrupted in between, the system will be corrupted beyond recovery.
158
Deployment Guide
7.6.2 Online Migration with YaST Wagon
If you have a SLES 11 SP2 system, find the needed steps at https://
www.suse.com/support/kb/doc.php?id=7011872. The following procedure applies to an online migration from SP2 to SP3.
NOTE: Registration Key
If add-ons are installed on your system, you might need to enter your registration key in order to update the system. Be prepared to have the key available.
1 When all requirements are met (see Section 7.5.1.1,
“Requirements” (page 149)), the update applet in the tray will display a message
that a distribution upgrade is available. Click it to start YaST Wagon. Alternatively
run /usr/sbin/wagon as root from the command line.
2 Confirm the Welcome dialog with Next.
3 If Wagon finds that the requirements are not met (required maintenance updates
are available but not yet installed) it will do an automatic self-update which may require a reboot. Follow the on-screen instructions.
4 Choose the update method in the following dialog. Choose Customer Center to use
the default setup (recommended).
Click Custom URL to manually choose the software channels used for the online migration. A list of channels will be displayed, providing the opportunity to
manually enable, disable, add, or delete channels. Add the SP3 update source(s).
This can either be the SP3 installation media or the SLES11-SP3-Pool and
SLES11-SP3-Updates channels. Click OK to return to the Update Method dialog.
If you want to review changes to the channel setup caused by the update process,
select Check Automatic Repository Changes.
Proceed with Next.
5 The system will be re-registered. During this process the SLES11-SP3-Pool
and SLES11-SP3-Updates channels will be added to the system (see Section 7.2.3, “Channel Model” (page 141) for more information). Confirm the addition of the channels.
Updating SUSE Linux Enterprise
159
6 If you have selected Check Automatic Repository Changes in the Update Method dialog, the list of repositories will be displayed, providing the opportunity to manually enable, disable, add, or delete channels. Proceed with OK when finished.
7 The Distribution Upgrade Settings screen opens presenting a summary of the update
configuration. The following sections are available:
Add-On Products
You may add SUSE Linux Enterprise Server add-on products or third-party
products here.
Update Options
Lists the actions that will be performed during the update. You can choose
whether to download all packages before installing them (default, recommended), or whether to download and install packages one by one.
Packages
Statistical overview of the update.
Backup
Set backup options.
Click Next and Start The Update to proceed.
IMPORTANT: Aborting the Online Migration
It is safe to abort the online migration on this screen prior to clicking Start
The Update and on all previous screens. Click Abort to leave the update
procedure and restore the system to the state it was in prior to starting
YaST Wagon. Follow the instructions on screen and perform a re-registration before leaving Wagon to remove the SP2 channels from your system.
8 During the update procedure the following steps are executed:
8a Packages will be updated.
8b SuSEconfig will be run.
8c The system will be rebooted (press OK).
8d The newly updated system will be re-registered.
160
Deployment Guide
9 Your system has been successfully updated to Service Pack 3.
7.6.3 Online Migration with zypper
NOTE: Registration Key
If add-ons are installed on your system, you might need to enter your registration key in order to update the system. Be prepared to have the key available.
1 When all requirements are met (see Section 7.5.1.1,
“Requirements” (page 149)), the “products” needed for the online migration
are added to /etc/products.d. Get a list of these products by running the
following command:
zypper se -t product | grep -h -- "-migration" | cut -d'|' -f2
This command should at least return SUSE_SLES-SP3-migration. Depending on the scope of your installation, more products may be listed.
2 Install the migration products retrieved in the previous step with the command
zypper in -t product LIST_OF_PRODUCTS, for example
zypper in -t product SUSE_SLES-SP3-migration
3 Register the products installed in the previous step in order to get the respective
update channels:
suse_register -d 2 -L /root/.suse_register.log
4 Refresh the repositories and services:
zypper ref -s
5 Check the list of repositories you can retrieve with zypper lr.
If any of these repositories is not enabled (the SP3 ones are not enabled by default when following this workflow), enable them with zypper modifyrepo --enable REPOSITORY ALIAS, for example:
zypper modifyrepo --enable SLES11-SP3-Pool SLES11-SP3-Updates
If your setup contains third-party repositories that may not be compatible with
SP3, disable them with zypper modifyrepo --disable REPOSITORY ALIAS.
Updating SUSE Linux Enterprise
161
6 Now everything is in place to perform the distribution upgrade with zypper
dup --from REPO 1 --from REPO 2 .... Make sure to list all needed repositories with --from, for example:
zypper dup --from SLES11-SP3-Pool --from SLES11-SP3-Updates
Confirm with y to start the upgrade.
7 Upon completion of the distribution upgrade from the previous step, run the following command:
zypper update -t patch
8 Now that the upgrade to SP3 has been completed, you need to re-register your
product:
suse_register -d 2 -L /root/.suse_register.log
9 Lastly, reboot your system.
10 Your system has been successfully updated to Service Pack 3.
7.7 Updating SLE 11 SP3 to SLE 11
SP4
There are different supported ways for updating a SUSE Linux Enterprise Server 11
SP3 system to a Service Pack 4. You may either update by using the online update
tools to install the respective patches (Online Migration) or update via the Service
Pack installation media. Furthermore, updates can be performed via servers hosting
Subscription Management Tool (SMT) or SUSE Manager.
An online migration is supported by the following tools:
• YaST wagon (graphical user interface)
• zypper (command line)
Alternatively, the full Service Pack media (DVD ISO image) can be downloaded.
Start the update process by booting from the physical Service Pack media or a network installation source.
162
Deployment Guide
7.7.1 Online Migration
Updating your system via online migration is done from within the running system.
You only need to reboot once, after the update is completed.
7.7.1.1 Requirements
In order to do an online update, the following requirements must be met. Make sure to
also read Section 7.4, “General Preparations for Updating” (page 146).
Product Registration
In order to be able to connect to the update channels, your product has to be registered. If it is not registered yet, either run the Novell Customer Center Configuration module in YaST or the suse_register command line tool to start the
registration.
Run an Online Update
Make sure the currently installed version has the latest patches installed. Run an
Online Update prior to the Online Migration. When using a graphical interface,
start the YaST Online Update or the updater applet. On the command line, run
the following commands (the last command needs to be run twice):
zypper ref -s
zypper update -t patch
zypper update -t patch
Reboot the system if needed.
See Section 1.0, YaST Online Update, (↑Administration Guide) or at Section
6.1.3, Updating Software with Zypper, (↑Administration Guide). for more information. on the online update tools.
Third-Party Software
If your setup involves third-party software or add-on software, test this procedure
on another machine to make sure that the dependencies are not broken by the update.
IMPORTANT: Always Run a Complete Online Migration
The online migration always has to be completed from beginning to end. If an
online migration is interrupted in between, the system is corrupted beyond recovery.
Updating SUSE Linux Enterprise
163
7.7.1.2 Online Migration with YaST Wagon
If you have a SLES 11 SP3 system, find the needed steps at https://
www.suse.com/support/kb/doc.php?id=7011872. The following procedure applies for an online migration from SP3 to SP4.
NOTE: Registration Key
If add-ons are installed on your system, you might need to enter your registration key in order to update the system. Be prepared to have the key available.
1 When all requirements are met (see Section 7.7.1.1,
“Requirements” (page 163)), the update applet in the tray will display a message that a distribution upgrade is available. Click it to start YaST Wagon. Alternatively run /usr/sbin/wagon as root from the command line.
2 Confirm the Welcome dialog with Next.
3 If Wagon finds that the requirements are not met (required maintenance updates
are available but not yet installed) it will do an automatic self-update which may
require a reboot. Follow the on-screen instructions.
4 Choose the update method in the following dialog. Choose Customer Center to
use the default setup (recommended).
Click Custom URL to manually choose the software channels used for the online migration. A list of channels will be displayed, providing the opportunity to
manually enable, disable, add, or delete channels. Add the SP4 update source(s).
This can either be the SP4 installation media or the SP4-Pool and SP4-Updates channels. Click OK to return to the Update Method dialog.
If you want to review changes to the channel setup caused by the update process,
select Check Automatic Repository Changes.
Proceed with Next.
5 The system will be re-registered. During this process the SP4-Pool and SP4Updates channels will be added to the system (see Section 7.2.3, “Channel
Model” (page 141) for more information). Confirm the addition of the channels.
164
Deployment Guide
6 If you have selected Check Automatic Repository Changes in the Update Method
dialog, the list of repositories will be displayed, providing the opportunity to
manually enable, disable, add, or delete channels. Proceed with OK when finished.
7 Choose the migration type:
Full migration
Updates all packages to the latest SP4 level.
Minimal Migration
Updates a minimal set of packages to the latest SP4 level.
Click Advanced to manually select the repositories used for upgrading. Confirm
your selection.
8 The Distribution Upgrade Settings screen opens presenting a summary of the update configuration. The following sections are available:
Add-On Products
You may add SUSE Linux Enterprise Server add-on products or third-party
products here.
Update Options
Lists the actions that will be performed during the update. You can choose
whether to download all packages before installing them (default, recommended), or whether to download and install packages one by one.
Packages
Statistical overview of the update.
Backup
Set backup options.
Click Next and Start The Update to proceed.
IMPORTANT: Aborting the Online Migration
It is safe to abort the online migration on this screen prior to clicking
Start The Update and on all previous screens. Click Abort to leave the
update procedure and restore the system to the state it was in prior to
starting YaST Wagon. Follow the instructions on screen and perform a
Updating SUSE Linux Enterprise
165
re-registration before leaving Wagon to remove the SP4 channels from
your system.
9 During the update procedure the following steps are executed:
1. Packages will be updated.
2. SuSEconfig will be run.
3. The system will be rebooted (press OK).
4. The newly updated system will be re-registered.
10 Your system has been successfully updated to Service Pack 4.
7.7.1.3 Online Migration with zypper
NOTE: Registration Key
If add-ons are installed on your system, you might need to enter your registration key in order to update the system. Be prepared to have the key available.
1 When all requirements are met (see Section 7.5.1.1,
“Requirements” (page 149)), the “products” needed for the online migration are
added to /etc/products.d. Get a list of these products by running the following command:
zypper se -t product | grep -h -- "-migration" | cut -d'|' -f2
This command should at least return SUSE_SLES-SP4-migration. Depending on the scope of your installation, more products may be listed.
2 Install the migration products retrieved in the previous step with the command
zypper in -t product LIST_OF_PRODUCTS, for example
zypper in -t product SUSE_SLES-SP4-migration
3 Register the products installed in the previous step in order to get the respective update channels:
suse_register -d 2 -L /root/.suse_register.log
4 Refresh the repositories and services:
166
Deployment Guide
zypper ref -s
5 Check the list of repositories you can retrieve with zypper lr. At least the following repositories need to be enabled:
• SLES11-SP4-Pool
• SLES11-SP4-Updates
Depending on the scope of your installation, further repositories for add-on products or extensions need to be enabled.
If any of these repositories is not enabled (the SP4 ones are not enabled by default
when following this workflow), enable them with zypper modifyrepo -enable REPOSITORY ALIAS, for example:
zypper modifyrepo --enable SLES11-SP4-Pool --enable SLES11-SP4-Updates
If your setup contains third-party repositories that may not be compatible with
SP4, disable them with zypper modifyrepo --disable REPOSITORY
ALIAS.
6 Now everything is in place to perform the distribution upgrade with zypper dup
--from REPO 1 --from REPO 2 .... Make sure to list all needed repositories with --from, for example:
zypper dup --from SLES11-SP4-Pool --from SLES11-SP4-Updates
Confirm with y to start the upgrade.
7 Upon completion of the distribution upgrade from the previous step, a minimal migration has been performed (a minimal set of packages has been updated to the latest SP4 level). Skip this step if you do not intend to do a full migration.
In order to do a Full Migration (updates all packages to the latest SP4 level), run
the following command:
zypper update -t patch
8 Now that the upgrade to SP4 has been completed, you need to re-register your
product:
suse_register -d 2 -L /root/.suse_register.log
9 Lastly, reboot your system.
Updating SUSE Linux Enterprise
167
Your system has been successfully updated to Service Pack 4.
7.7.1.4 Updating by Booting from an Installation
Source
As an alternative to the Online Migration you may also update your system by booting
from an installation source—either a DVD or a network installation source. The update will start like a normal installation.
Service Pack 4 ISO images can be obtained from http://
download.suse.com/. Either burn it to a DVD or prepare a network installation
source as described in Section 14.2, “Setting Up the Server Holding the Installation
Sources” (page 254).
7.7.2 Getting Packages from Older
Service Packs
In order to install packages from an older Service Pack, add the respective repositories of the older Service Pack. This can be done via:
root # zypper ar URL ALIAS
ALIAS can be any string which will identify the repository inside the system. We
strongly recommend to add both *-POOL and *-UPDATES repositories of the respective Service Pack.
The easiest way to find the URL is having a local mirror, ideally provided by a local
SMT server. After the repository is mirrored on SMT, find the repositories via pointing your browser to http://SMT_HOSTNAME/repo. A typical URL looks like
this: http://SMT_HOSTNAME/repo/$RCE/SLES11-SP1-POOL/sle-11x86_64. If you have staging enabled, you can also browse the staged repositories.
7.8 Backporting Source Code
SUSE uses backports extensively. The information in this section helps you understand why it can be deceptive to compare version numbers in order to judge
software's capabilities and problems.
168
Deployment Guide
7.8.1 Why Backporting?
Upstream developers are primarily concerned with advancing the software they develop. In many cases they combine fixing bugs with introducing new features which have
not yet received extensive testing and which may introduce new bugs.
For distribution developers, it is important to distinguish between:
• bugfixes with a limited potential for disrupting functionality; and
• changes that may disrupt existing functionality.
In most cases, distribution developers do not follow all upstream changes once a package has become part of a released distribution. Usually they stick instead with the
upstream version that they initially released and create patches based on upstream
changes to fix bugs. This practice is known as backporting.
Distribution developers generally will only introduce a newer version of software in
two cases:
• when the changes between their packages and the upstream versions have become
so large that backporting is no longer feasible, or
• for software that inherently ages badly, like anti-malware software.
7.8.2 Reasons for Backporting
SUSE uses backports extensively as we strike a good balance between a number of
concerns for enterprise software. The most important of these are:
• Having stable interfaces (APIs) that software vendors can rely on when building
products for use on SUSE's enterprise products.
• Ensuring that packages used in the release of SUSE's enterprise products are of the
highest quality and have been thoroughly tested, both in themselves and as part of
the whole enterprise product.
• Maintaining the various certifications of SUSE's enterprise products by other vendors, like certifications for Oracle or SAP products.
Updating SUSE Linux Enterprise
169
• Allowing SUSE's developers to focus on making the next version of the product
as good as they can make it, rather than them having to spread their focus thinly
across a wide range of releases.
• Keeping a clear view of what is in a particular enterprise release, so that our support
can provide accurate and timely information about it.
7.8.3 Reasons against Backports
It is a general policy rule that no new upstream versions of a package are introduced
into our enterprise products. This rule is not an absolute rule however. For a limited
class of packages, in particular anti-virus software, security concerns weigh heavier
than the conservative approach that is preferable from the perspective of quality assurance. For packages in that class, occasionally newer versions are introduced into a
released version of an enterprise product line.
Sometimes also for other types of packages the choice is made to introduce a new
version rather than a backport. This is done when producing a backport is not economically feasible or when there is a very relevant technical reason to introduce the
newer version.
7.8.4 The Implications of Backports for
Interpreting Version Numbers
Due to the practice of backporting, one cannot simply compare version numbers
to determine whether a SUSE package contains a fix for a particular issue or has
had a particular feature added to it. With backporting, the upstream part of a SUSE
package's version number merely indicates what upstream version the SUSE package
is based on. It may contain bug fixes and features that are not in the corresponding upstream release, but that have been backported into the SUSE package.
There are a number of locations where information regarding such bug fixes and features is stored:
• The package's changelog:
rpm -q --changelog name-of-installed-package
rpm -qp --changelog packagefile.rpm
170
Deployment Guide
The output briefly documents the change history of the package.
• The package changelog may contain entries like bnc#1234 that refer to bugs in
Novell's Bugzilla tracking system or links to other bugtracking systems. (Due to
confidentiality policies, not all such information may be accessible to you).
• A package may contain a /usr/share/doc/packagename/README.SUSE
or README.SuSE file which contains general, high-level information specific to
the SUSE package.
• The RPM source package contains the patches that were applied during the
building of the regular binary RPMs as separate files that can be interpreted if
you are familiar with reading source code. See the Maximum RPM [http://
www.rpm.org/max-rpm/] book for more information.
• For security bug fixes, the SUSE security announcements [https://
www.suse.com/support/security/#1]. These often refer to bugs
through standardized names like CAN-2005-2495 which are maintained by the
Common Vulnerabilities and Exposures [http://cve.mitre.org] project.
One particular area where this limited value of version numbers when backporting is
involved can cause problems is with security scanning tools. Some security vulnerability scanning tools (or particular tests in such tools) operate solely on version information. These tools/tests are thus prone to generating “false positives” (claims that a vulnerable piece of software has been found which in fact isn't vulnerable) when backports are involved. When evaluating reports from security scanning tools, one should
always investigate whether an entry is based just on a version number or on an actual
test of whether an actual vulnerability exists.
7.9 The Atomic Update
The Atomic Update is based on tools that manage two copies of the system and allow
easy recovery after an update failure. The delivered tools require a special disk partition setup. Every copy of the system resides on a primary partition of its own. If an
update fails, you can always switch back to the previous state of the system, which is
available on the other partition.
Updating SUSE Linux Enterprise
171
7.9.1 Setup
WARNING: Strict Partitioning Requirements
The implementation has strict requirements on disk partitioning: the first root
partition is /dev/sda1 and must not occupy more than half of the entire disk
size. Then the tools will create /dev/sda2 for the system's second root partition. Further partitions if available are shared on both root partitions—take
their size into account, and reduce the size of the first partition accordingly;
this is a rough calculation:
The size of the complete disk minus size of sda1 minus sda2 is the free
space of additional partitions.
1 Install the system with /dev/sda1 as the single root partition and with less than
half of the entire disk size.
2 Customize the installed system as needed. Make sure to have the multi-update-tools package installed.
3 Run multi-update-setup --partition, which creates the system's second root partition (/dev/sda2) of the similar size.
4 Partition the rest of the disk as needed and continue with customizations(*).
5 Run multi-update-setup --clone to copy the system to the other partition. With this command you also change the / (root) entry in /etc/fstab of
the target system.
6 If needed, do further customizations(*).
7 Run multi-update-setup --bootloader to initialize the boot loader setup. The boot loader menu will then contain an entry to boot the other system.
WARNING: GRUB Bootloader Mandatory
Installation of the GRUB boot loader is mandatory. The tools are not compatible with other boot loaders.
8 If there are no customizations to be done as marked with (*), run multi-update-setup --complete which performs all the three steps.
172
Deployment Guide
7.9.2 Updating the Other System
Run multi-update. This command runs zypper in a chroot environment and
updates the other system—it does not matter which one is active. Its boot menu will
be offered as the default at boot time.
7.9.3 Troubleshooting
If the updated system has a damaged boot loader after the update, you must change
the “Active” flag and set it for the root partition of the other system in order to boot
it.
If the updated system does not boot at all, you need access to the boot loader menu to
select the other system.
For more information about GRUB, see Chapter 11, The Boot Loader GRUB (↑Administration Guide).
7.9.4 Limitation
The root partition must be mounted by partition name, by ID, or in another way.
Mounting by partition UUID or by label is not supported.
7.9.5 For More Information
For more information, see /usr/share/doc/packages/multi-up​
date-tools/README coming with the multi-update-tools package.
7.10 Migration Hooks for YaST
Wagon
Migration hooks allow you to run a custom external script at some point during the
migration process. These scripts allow you to handle specific problems that cannot
Updating SUSE Linux Enterprise
173
be handled via the usual RPM scripts, or allow you to perform any extra actions that
might be needed during migration (not required during normal package update).
The migration hooks are executed with root privileges so it is possible to do any maintenance tasks in the scripts (starting/stopping services, data backup, data migration,
etc...). The scripts must not be interactive; STDIN and STDOUT are redirected to
pipes when running in YaST. The X session should not be used, as it might not be
available in all cases (e.g. when running in text mode). Do not forget to set the executable permission for the hook scripts.
Migration hooks are supported in yast2-wagon package version 2.17.32.1 (provided as an update for SLES11-SP2) or 2.17.34 (included in SLES11-SP3) or higher versions.
7.10.1 Hook Script Location and Name
Conventions
The scripts are searched in /var/lib/YaST2/wagon/hooks/ directory. The
expected script name is in the format step_seq_prefix_name, where:
step
is a predefined migration step name, describing the current migration step.
seq
is a sequence number in range 00...99, which makes it possible to set the order
in which the scripts are executed. (It is important to keep the beginning zeros for
correct sorting!)
prefix
should be unique to avoid conflicts (like a namespace). Use package name (if it
is part of a package) or your vendor name, Internet domain name, etc., basically
anything that can be considered sufficiently unique
name
can be any string (just to differentiate the scripts). Some descriptive name is recommended.
Example 7.2: Hook Script with Full Path
/var/lib/YaST2/wagon/hooks/before_package_migration_00_postgresql_backup
174
Deployment Guide
7.10.2 Hook Script Exit Value
The script should return exit value 0. If it fails (any non-zero exit value) an error message is displayed in Wagon and it is possible to restart the script, ignore the failure
(and continue with other scripts) or completely cancel the hooks for the current step
and stage.
7.10.3 Idempotent Scripts
The hook scripts can be potentially run more times (when going back and forth in the
Wagon dialogs, Wagon might restart itself or some steps might be executed multiple
times in the migration workflow), so the scripts have to cope with that fact (they can
check at the beginning whether they need to do the action or the action has been already done or they can create a simple temporary stamp file or otherwise solve multiple runs properly).
7.10.4 List of Supported Hooks
Some hooks are optional (because the depend on the previous results or depend on
user selected values). Note that some hooks are called multiple times (e.g. registration
is called before migration and after migration). Here is the list of supported hooks
(step names) in execution order:
before_init
started at the very beginning (note: it is called again after Wagon restarts)
before_welcome , after_welcome
started before/after displaying the welcome dialog
before_registration_check , after_registration_check
Wagon checks the registration status (if registration of some products has expired
the migration might fail). If everything is OK, no dialog is displayed and Wagon
automatically continues with the next step
before_custom_url , after_custom_url
repository manager is started (optional, in Patch CD mode only)
before_self_update , after_self_update
called before/after Wagon updates itself (to ensure the latest version is used for
migration)
Updating SUSE Linux Enterprise
175
before_installing_migration_products ,
after_installing_migration_products
called before/after installing the migration products
before_selecting_migration_source ,
after_selecting_migration_source
Wagon asks the user to migrate via Novell Customer Center repositories or using
a custom repository; the next step depends on the user selection
before_registration , after_registration
running SUSE register (to add migration repositories)
before_repo_selection , after_repo_selection
manual repository management
before_set_migration_repo , after_set_migration_repo
selecting migration repositories (full/minimal migration when using Novell Customer Center) or update repository selection (custom repository migration)
before_package_migration
before package update starts, after this step the real migration starts and it is not
possible to go back to the previous state automatically (aborting in this phase results in an inconsistent (half upgraded) system, and manual rollback is needed)
before_registration , after_registration
running SUSE register (to register updated products)
before_congratulate , after_congratulate
before/after Wagon displays the congratulation dialog as a result of a successful
migration
before_exit
called just before Wagon exits (always, regardless the migration result, also after
abort and at restart)
7.10.5 Abort Hooks
These are special abort hooks which are called when the user aborts the migration.
These hooks can be called in any step in the migration workflow therefore the execution order cannot be guaranteed. The scripts need to check the current state if they rely on the results of other hooks.
176
Deployment Guide
before_abort
user confirmed aborting the migration
before_abort_rollback , after_abort_rollback
user confirmed rollback after abort (reverting to the old products installed before
starting migration). These hooks are called after before_abort and skipped when
the user does not confirm rollback.
7.10.6 Restart Hooks
These hooks are called whenever Wagon restarts itself.
before_restart
Wagon is finishing and will be started again
after_restart
Wagon has restarted and runs the next step in the migration workflow
7.10.7 Usually Used Hooks
The list of hooks is fairly large, but many of them only make sense in special cases. In
normal use cases these should be given preference:
• To do some action before the system is migrated (still running the previous version)
use the before_package_migration hook.
At this point it is clear that the migration is ready and is about to start, whereas in
all steps before it was possible to abort the migration.
• To do some action after the system has migrated (the system is running the new migrated version, but some things might not be active yet, e.g. updated kernel requires
reboot, updated services might need restart etc..), use before_congratulate
or after_congratulate hook.
This can be also used for cleaning up the temporary results of the
before_package_migration hook. At this point the migration has successfully finished.
• To reverse the changes if the migration is aborted, use one of the abort hooks depending on the case. Keep in mind that the abort hooks can be called anytime, so
Updating SUSE Linux Enterprise
177
the revert might not be needed (the hook that does the changes might not have been
called yet). The abort hooks need to check the current state.
7.10.8 Obsolete Hooks
Older versions of Wagon supported only two hook scripts: /usr/lib/
YaST2/bin/wagon_hook_init and /usr/lib/YaST2/bin/
wagon_hook_finish. The problem was that only one script could be run as a
hook and it was not possible to put hooks directly into RPM packages.
These old hook scripts are still supported in newer versions of Wagon for backward
compatibility, but the new hooks before_init and before_exit should be
used instead of the obsolete ones.
178
Deployment Guide
Setting Up Hardware
Components with YaST
YaST allows you to configure hardware items at installation time as well as on an
already-installed system. Configure audio hardware, printers or scanner support or
learn which hardware components are connected to your computer by using the YaST
Hardware Information module.
8
TIP: Graphics card, monitor, mouse and keyboard settings
Graphics card, monitor, mouse and keyboard can be configured with either
KDE or GNOME tools.
8.1 Hardware Information
Use the YaST hardware information module if you want to know more about your
hardware or if you need to find out details like vendor and model of a certain piece of
hardware to be able to properly configure it.
1 Start YaST and click Hardware > Hardware Information. Hardware probing starts
immediately and it will take some time until you see the hardware information tree
in a separate window.
2 In the hardware information tree recursively click on the plus icons to expand the
information about a specific device.
3 Click Save to File... to save the output to a file.
4 Click Close to leave the hardware information overview.
Setting Up Hardware Components with YaST
179
8.2 Setting Up Graphics Card and
Monitor
After the installation you can change the configuration of your graphics system
(graphics card and monitor) according to your needs. Such a change may be necessary
because of accessibility issues or hardware upgrades.
WARNING: Changing Monitor Frequencies
Although there are safety mechanisms, you should still be very careful when
manually changing the allowed monitor frequencies. Incorrect values can
damage your monitor. Always refer to the monitor's manual before changing
frequencies.
Change the resolution, if fonts are too small or if circles appear misshapen. Proceed
as follows:
1 In YaST, click Hardware > Graphics Card and Monitor. SaX2 checks the system
resources and displays a window.
2 Make sure the monitor is properly detected. If not, use Change to select the appropriate model from the list.
3 Select an appropriate Resolution and Colors, if necessary.
180
Deployment Guide
4 Test the new configuration before it is applied to the system. Click Ok to decide
what to do with your configuration (Test, Save, or Cancel.)
To activate a second monitor, proceed as follows:
1 In YaST, click Hardware > Graphics Card and Monitor. SaX2 checks the system
resources and displays the Card and Monitor Properties dialog.
2 Make sure the monitor is properly detected. If not, use Change to select the appropriate model from the list.
3 Enable Activate Dual Head Mode and click Configure for further fine-tuning.
4 Make sure the second monitor is properly detected. If not, use Change to select the
appropriate model from the list.
5 Decide whether you want to use the second monitor in Cloned Multihead or in Xinerama Multihead mode and click Ok.
6 Test the new configuration before it is applied to the system. Click Ok to decide
what to do with your configuration (Test, Save, or Cancel.)
NOTE: Restarting the X Server
Any changes you make here take effect only after you restart the X server. If
you want to restart the X server now, log out of the graphical system and log
in again.
8.3 Setting Up Keyboard and
Mouse
Reconfigure input devices such as the keyboard or the mouse, or add more than one
of these devices using the YaST Keyboard and Mouse modules.
8.3.1 Keyboard Layout
Setting Up Hardware Components with YaST
181
In case you want to replace a standard 104-key keyboard with a multimedia keyboard
or use a different language or country layout, proceed as follows:
1 In YaST, click Hardware > Keyboard Layout. The SaX2 configuration tool reads
the system resources and displays the Keyboard Properties dialog.
2 Select your keyboard model from the Type list.
3 Select the country in the Layout list.
4 Depending on the country layout, you can choose a certain Variant. The selections
are applied immediately for testing.
5 As an option you can enable Additional Layouts. Check one or more boxes in the
list. This feature is handy if you want to switch between different languages or
scripts in the running system without the need for reconfiguration.
6 Before saving the configuration, use the Test field at the bottom of the dialog to
check if special characters like umlauts and accented characters can be entered and
displayed correctly.
7 Click OK to leave the configuration dialog and in the following message click Save
to apply your changes.
182
Deployment Guide
NOTE: Configuring Console Keyboard Layout
By clicking the Save button as described in Step 7 (page 182) the setup
of the console keyboard layout takes place at the same time. If you want to
change the console keyboard layout, either call yast keyboard (the text
mode interface) or check the KEYTABLE and YAST_KEYBOARD settings in /
etc/sysconfig/keyboard.
8.3.2 Mouse Model
The mouse is usually detected automatically, but you can set up your mouse model
manually if the automatic detection fails. Refer to the documentation of your mouse
for a description of the model. If you want to modify your mouse configuration, proceed as follows:
1 In YaST, click Hardware > Mouse Model. The SaX2 configuration tool reads the
system resources and displays the Mouse Properties dialog.
2 Click Change and select your mouse model from the list displayed.
3 Click OK to leave the configuration dialog and apply your changes with Save.
In the Options part of the dialog, set various options for operating your mouse.
Activate 3-Button Emulation
If your mouse has only two buttons, a third button is emulated whenever you click
both buttons simultaneously.
Activate Mouse Wheel
Check this box to use a scroll wheel.
Invert X-Axis / Invert Y-Axis
Check these options if you want to change the direction in which the mouse
pointer moves.
Activate Left-Hand Button Mapping
Check this box to make the button mapping suitable for left-hand usage.
Emulate Wheel with Mouse Button
If your mouse does not have a scroll wheel but you would like to use a similar
functionality, you can assign an additional button for this. Select the button to use.
Setting Up Hardware Components with YaST
183
While pressing this button, any movement of the mouse is translated into scroll
wheel commands. This feature is especially useful with trackballs.
8.4 Setting Up Sound Cards
YaST detects most sound cards automatically and configures them with the appropriate values. If you want to change the default settings, or need to set up a sound card
that could not be configured automatically, use the YaST sound module. There, you
can also set up additional sound cards or switch their order.
To start the sound module, start YaST and click Hardware > Sound. Alternatively,
start the Sound Configuration dialog directly by running yast2 sound & as user
root from a command line.
The dialog shows all sound cards that could be detected.
Procedure 8.1: Configuring Sound Cards
If you have added a new sound card or YaST could not automatically configure an existing sound card, follow the steps below. For configuring a new sound card, you need
184
Deployment Guide
to know your sound card vendor and model. If in doubt, refer to your sound card documentation for the required information. For a reference list of sound cards supported by ALSA with their corresponding sound modules, see http://www.alsaproject.org/main/index.php/Matrix:Main.
During configuration, you can choose between the following setup options:
Quick Automatic Setup
You are not required to go through any of the further configuration steps—the
sound card is configured automatically. You can set the volume or any options
you want to change later.
Normal Setup
Allows you to adjust the output volume and play a test sound during the configuration.
Advanced setup with possibility to change options
For experts only. Allows you to customize all parameters of the sound card.
IMPORTANT: Advanced Configuration
Only use this option if you know exactly what your are doing. Otherwise
leave the parameters untouched and use the normal or the automatic setup options.
1 Start the YaST sound module.
2 To configure a detected, but Not Configured sound card, select the respective entry
from the list and click Edit.
To configure a new sound card, click Add. Select your sound card vendor and model and click Next.
3 Choose one of the setup options and click Next.
4 If you have chosen Normal Setup, you can now Test your sound configuration and
make adjustments to the volume. You should start at about ten percent volume to
avoid damage to your hearing or the speakers.
5 If all options are set according to your wishes, click Next.
Setting Up Hardware Components with YaST
185
The Sound Configuration dialog shows the newly configured or modified sound
card.
6 To remove a sound card configuration that you no longer need, select the respective entry and click Delete.
7 Click OK to save the changes and leave the YaST sound module.
Procedure 8.2: Modifying Sound Card Configurations
1 To change the configuration of an individual sound card (for experts only!), select
the sound card entry in the Sound Configuration dialog and click Edit.
This takes you to the Sound Card Advanced Options where you can fine-tune a
number of parameters. For more information, click Help.
2 To adjust the volume of an already configured sound card or to test the sound
card, select the sound card entry in the Sound Configuration dialog and click Other.
Select the respective menu item.
NOTE: YaST Mixer
The YaST mixer settings provide only basic options. They are intended for
troubleshooting (for example, if the test sound is not audible). Access the
YaST mixer settings from Other > Volume. For everyday use and fine-tuning of sound options, use the mixer applet provided by your desktop or the
alsasound command line tool.
3 For playback of MIDI files, select Other > Start Sequencer.
4 When a supported sound card is detected (like a Creative Soundblaster
Live, Audigy or AWE sound card), you can also install SoundFonts for playback
of MIDI files:
4a Insert the original driver CD-ROM into your CD or DVD drive.
4b Select Other > Install SoundFonts to copy SF2 SoundFonts™ to your hard
disk. The SoundFonts are saved in the directory /usr/share/sf​
bank/creative/.
186
Deployment Guide
5 If you have configured more than one sound card in your system you can adjust the
order of your sound cards. To set a sound card as primary device, select the sound
card in the Sound Configuration and click Other > Set as the Primary Card. The
sound device with index 0 is the default device and thus used by the system and the
applications.
6 Per default, SUSE Linux Enterprise Server uses the PulseAudio sound system. It is
an abstraction layer that helps to mix multiple audio streams, bypassing any restrictions the hardware may have. To enable or disable the PulseAudio sound system,
click Other > PulseAudio Configuration. If enabled, PulseAudio daemon is used
to play sounds. Disable PulseAudio Support in case you want to use something else
system-wide.
The volume and configuration of all sound cards are saved when you click OK and
leave the YaST sound module. The mixer settings are saved to the file /etc/
asound.state. The ALSA configuration data is appended to the end of the file /
etc/modprobe.d/sound and written to /etc/sysconfig/sound.
8.5 Setting Up a Printer
YaST can be used to configure a local printer that is directly connected to your machine (normally with USB or parallel port) and to set up printing with network printers. It is also possible to share printers over the network. Further information about
printing (general information, technical details, and troubleshooting) is available in
Chapter 14, Printer Operation (↑Administration Guide).
In YaST, click Hardware > Printer to start the printer module. By default it opens in
the Printer Configurations view, displaying a list of all printers that are available and
configured. This is especially useful when having access to a lot of printers via the
network. From here you can also Print a Test Page and configure local printers.
8.5.1 Configuring Local Printers
Usually a local USB printer is automatically detected. There are two possible reasons
why a USB printer is not automatically detected:
• The USB printer is switched off.
Setting Up Hardware Components with YaST
187
• The communication between printer and computer is not possible. Check the cable
and the plugs to make sure that the printer is properly connected. If this is the case,
the problem may not be printer-related, but rather a USB-related problem.
Configuring a printer is basically a three-step process: specify the connection type,
choose a driver, and name the printing queue for this setup.
For many printer models, several drivers are available. When configuring the printer,
YaST defaults to the one marked recommended as a general rule. Normally it is not
necessary to change the driver—the recommended one should produce the best results. However, if you want a color printer to print only in black and white, it is most
convenient to use a driver that does not support color printing, for example. If you experience performance problems with a PostScript printer when printing graphics, it
may help to switch from a PostScript driver to a PCL driver (provided your printer
understands PCL).
If no driver for your printer is listed, try to select a generic driver with an appropriate standard language from the list. Refer to your printer's documentation to
find out which language (the set of commands controlling the printer) your printer understands. If this does not work, refer to Section 8.5.1.1, “Adding Drivers with
YaST” (page 189) for another possible solution.
A printer is never used directly, but always through a print queue. This ensures that simultaneous jobs can be queued and processed one after the other. Each print queue
is assigned to a specific driver, and a printer can have multiple queues. This makes it
possible to set up a second queue on a color printer that prints black and white only,
for example. Refer to Section “The Workflow of the Printing System” (Chapter 14,
Printer Operation, ↑Administration Guide) for more information about print queues.
Procedure 8.3: Adding a New Local Printer
1 Start the YaST printer module with Hardware > Printer.
2 In the Printer Configurations screen click Add.
3 If your printer is already listed under Specify the Connection, proceed
with the next step. Otherwise, try to Detect More or start the Connection Wizard.
4 In the input box under Find and Assign a Driver enter the vendor name
and the model name and click Search for.
188
Deployment Guide
5 Choose the driver marked as recommended that best matches your printer. If no
suitable driver is displayed:
5a Check your search term
5b Broaden your search by clicking Find More
5c Add a driver as described in Section 8.5.1.1, “Adding Drivers with
YaST” (page 189)
6 Specify the Default paper size.
7 In the Set Arbitrary Name field, enter a unique name for the print queue.
8 The printer is now configured with the default settings and ready to use. Click OK
to return to the Printer Configurations view. The newly configured printer is now
visible in the list of printers.
8.5.1.1 Adding Drivers with YaST
If no suitable driver is available in the Find and Assign a Driver dialog when adding
a new printer, no PPD (PostScript Printer Description) file for your model is
available. For more information about PPD files, refer to Section “Installing the
Software” (Chapter 14, Printer Operation, ↑Administration Guide).
Get PPD files directly from your printer vendor or from the driver CD of a PostScript
printer. For details, see Section “No Suitable PPD File Available for a PostScript
Printer” (Chapter 14, Printer Operation, ↑Administration Guide). Alternatively, find PPD files at http://www.linuxfoundation.org/collabo​
rate/workgroups/openprinting/database/databaseintro, the
“OpenPrinting.org printer database”. When downloading PPD files from OpenPrinting, keep in mind that it always shows the latest Linux support status, which is not
necessarily met by SUSE Linux Enterprise Server.
Procedure 8.4: Adding a PPD file
1 Start the YaST printer module with Hardware > Printer.
2 In the Printer Configurations screen, click Add.
3 In the Find and Assign a Driver section, click Driver Packages.
Setting Up Hardware Components with YaST
189
4 Enter the full path to the PPD file into the input box under Make a Printer
Description File Available. Alternatively, choose the file from a dialog box by clicking Browse.
5 Click OK to return to the Add New Printer Configuration screen.
6 In order to directly use this PPD file, proceed as described in Procedure 8.3,
“Adding a New Local Printer” (page 188). Otherwise, click Cancel.
8.5.1.2 Editing a Local Printer Configuration
By editing an existing configuration for a local printer you cannot only change basic
settings as connection type and driver, but also adjust the default settings for paper
size, resolution, media source, etc. You can change the identifier of the printer by altering the printer descriptions.
Procedure 8.5: Editing a Local Printer
1 Start the YaST printer module with Hardware > Printer.
2 In the Printer Configurations screen, choose a local printer from the list and click
Edit.
3 Change the connection type or the driver as described in Procedure 8.3, “Adding a
New Local Printer” (page 188). This should only be necessary in case you have
problems with the current configuration.
4 Make this printer the default by checking Default Printer.
5 Adjust the default settings by clicking All Options for the Current Driver. To
change a setting, expand the list of options by clicking the relative + sign. Change
the default by clicking an option. Apply your changes with OK.
8.5.2 Configuring Printing via the Network
with YaST
Network printers are not detected automatically. They must be configured manually
using the YaST printer module. Depending on your network setup, you can print to a
print server (CUPS, LPD, SMB, or IPX) or directly to a network printer (preferably
190
Deployment Guide
via TCP). Access the configuration view for network printing by choosing Printing via
Network from the left pane in the YaST printer module.
8.5.2.1 Using CUPS
In a Linux environment CUPS is usually used to print via the network. The simplest
setup is to only print via a single CUPS server which can directly be accessed by all
clients. Printing via more than one CUPS server requires a running local CUPS daemon that communicates with the remote CUPS servers.
Procedure 8.6: Printing via a Single CUPS Server
1 Start the YaST printer module with Hardware > Printer.
2 From the left pane, launch the Print via Network screen.
3 Check Do All Your Printing Directly via One Single CUPS Server and specify the
name or IP address of the server.
4 Click Test Server to make sure you have chosen the correct name or IP address.
5 Click OK to return to the Printer Configurations screen. All printers available via
the CUPS server are now listed.
Procedure 8.7: Printing via Multiple CUPS Servers
1 Start the YaST printer module with Hardware > Printer.
2 From the left pane, launch the Print via Network screen.
3 Check Accept Printer Information from the Following Servers
4 Under General Settings specify which servers to use. You may accept connections from all networks available, from the local network, or from specific
hosts. If you choose the latter option, you need to specify the hostnames or IP addresses.
5 Confirm by clicking OK and then Yes when asked to start a local CUPS server.
After the server has started YaST will return to the Printer Configurations screen.
Click Refresh list to see the printers detected by now. Click this button again, in
case more printer are to be available.
Setting Up Hardware Components with YaST
191
8.5.2.2 Using Print Servers other than CUPS
If your network offers print services via print servers other than CUPS, start the YaST
printer module with Hardware > Printer and launch the Print via Network screen from
the left pane. Start the Connection Wizard and choose the appropriate Connection
Type. Ask your network administrator for details on configuring a network printer in
your environment.
8.5.3 Sharing Printers Over the Network
Printers managed by a local CUPS daemon can be shared over the network and so
turn your machine into a CUPS server. Usually you share a printer by enabling CUPS'
so-called “browsing mode”. If browsing is enabled, the local print queues are made
available on the network for listening to remote CUPS daemons. It is also possible to
set up a dedicated CUPS server that manages all printing queues and can directly be
accessed by remote clients. In this case it is not necessary to enable browsing.
Procedure 8.8: Sharing Printers
1 Start the YaST printer module with Hardware > Printer.
2 Launch the Share Printers screen from the left pane.
3 Select Allow Remote Access. For more detailed configuration, additional options
are available:
• Check For computers within the local network and enable browsing mode by also
checking Publish printers by default within the local network.
• Add the network interface to be used by the CUPS server. If you want to share
your printers via specified network interfaces, add those in the input box below.
• To restrict access to your CUPS server to certain networks or IP addresses, specify these via the two input boxes.
4 Click OK to restart the CUPS server and to return to the Printer Configurations
screen.
5 Regarding CUPS and firewall settings, see http://en.opensuse.org/
SDB:CUPS_and_SANE_Firewall_settings.
192
Deployment Guide
8.6 Setting Up a Scanner
You can configure a USB or SCSI scanner with YaST. The sane-backends package contains hardware drivers and other essentials needed to use a scanner. Scanners
connected to a parallel port cannot be configured with YaST. If you own a HP All-InOne device, see Section 8.6.1, “Configuring an HP All-In-One Device” (page 193),
instructions on how to configure a network scanner are available at Section 8.6.3,
“Scanning over the Network” (page 194).
Procedure 8.9: Configuring a USB or SCSI Scanner
1 Connect your USB or SCSI scanner to your computer and turn it on.
2 Start YaST and select Hardware > Scanner. YaST builds the scanner database and
tries to detect your scanner model automatically.
If a USB or SCSI scanner is not properly detected, try Other > Restart Detection.
3 To activate the scanner select it from the list of detected scanners and click Edit.
4 Choose your model form the list and click Next and Finish.
5 Use Other > Test to make sure you have chosen the correct driver.
6 Leave the configuration screen with OK.
8.6.1 Configuring an HP All-In-One Device
An HP All-In-One device can be configured with YaST even if it is connected to the
parallel port or is made available via the network. If you own a USB HP All-In-One
device, start configuring as described in Procedure 8.9, “Configuring a USB or SCSI
Scanner” (page 193). If it is detected properly and the Test succeeds, it is ready to
use.
If your USB device is not properly detected, or your HP All-In-One device is connected to the parallel port or the network, run the HP Device Manager:
1 Start YaST and select Hardware > Scanner. YaST loads the scanner database.
Setting Up Hardware Components with YaST
193
2 Start the HP Device Manager with Other > Run hp-setup and follow the on-screen
instructions. After having finished the HP Device Manager, the YaST scanner
module automatically restarts the auto detection.
3 Test it by choosing Other > Test.
4 Leave the configuration screen with OK.
8.6.2 Sharing a Scanner over the Network
SUSE Linux Enterprise Server allows the sharing of a scanner over the network. To
do so, configure your scanner as follows:
1 Configure the scanner as described in Section 8.6, “Setting Up a
Scanner” (page 193).
2 Choose Other > Scanning via Network.
3 Enter the hostnames of the clients (separated by a comma) that should be allowed
to use the scanner under Server Settings > Permitted Clients for saned and leave the
configuration dialog with OK.
8.6.3 Scanning over the Network
To use a scanner that is shared over the network, proceed as follows:
1 Start YaST and select Hardware > Scanner.
2 Open the network scanner configuration menu by Other > Scanning via Network.
3 Enter the hostname of the machine the scanner is connected to under Client Settings
> Servers Used for the net Metadriver
4 Leave with OK. The network scanner is now listed in the Scanner Configuration
window and is ready to use.
194
Deployment Guide
Installing or Removing
Software
9
Use YaST's software management tool to search for software components you want
to add or remove. YaST resolves all dependencies for you. To install packages not
shipped with the installation media, add additional software repositories to your setup
and let YaST manage them. Keep your system up-to-date by managing software updates with the update applet.
Change the software collection of your system with the YaST Software Manager. This
YaST module is available in two toolkit flavors: Qt and ncurses; the Qt flavor is described here.
NOTE: Confirmation and Review of Changes
When installing, updating or removing packages, any changes in the Software Manager are not applied immediately but only after confirming them
with Accept or Apply respectively. YaST maintains a list with all actions, allowing you to review and modify your changes before applying them to the
system.
9.1 Definition of Terms
Repository
A local or remote directory containing packages, plus additional information
about these packages (package meta-data).
Installing or Removing Software
195
(Repository) Alias
A short name for a repository used by various Zypper commands. The alias can
be chosen by the user when adding a repository and must be unique.
Product
Represents a whole product, for example SUSE® Linux Enterprise Server.
Pattern
A pattern is an installable group of packages dedicated to a certain purpose. For
example, the Laptop pattern contains all packages that are needed in a mobile
computing environment. Patterns define package dependencies (such as required
or recommended packages) and come with a preselection of packages marked for
installation. This ensures that the most important packages needed for a certain
purpose are available on your system after installation of the pattern. However,
not necessarily all packages in a pattern are preselected for installation and you
can manually select or deselect packages within a pattern according to your needs
and wishes.
Package
A package is a compressed file in rpm format that contains the files for a particular program.
Patch
A patch consists of one or more packages and may be applied by means of
deltarpms. It may also introduce dependencies to packages that are not installed
yet.
Resolvable
An generic term for product, pattern, package or patch. The most commonly used
type of resolvable is a package or a patch.
deltarpm
A deltarpm consists only of the binary diff between two defined versions of a
package, and therefore has the smallest download size. Before being installed, the
full RPM package is rebuilt on the local machine.
Package Dependencies
Certain packages are dependent on other packages, such as shared libraries. In
other terms, a package may require other packages—if the required packages
are not available, the package cannot be installed. In addition to dependencies
(package requirements) that must be fulfilled, some packages recommend other packages. These recommended packages are only installed if they are actually
196
Deployment Guide
available, otherwise they are just ignored and the package recommending them is
installed nevertheless.
9.2 Using the KDE Interface (Qt)
The YaST Qt interface is started by default when using the desktops KDE, icewm,
and others. It is also used when invoking YaST from a remote terminal. Start the software manager from the YaST Control Center by choosing Software > Software Management.
9.2.1 Views for Searching Packages or
Patterns
The YaST software manager can install packages or patterns from all currently enabled repositories. It offers different views and filters to make it easier to find the
Installing or Removing Software
197
software you are searching for. The Search view is the default view of the window.
To change view, click View and select one of the following entries from the dropdown list. The selected view opens in a new tab.
Patterns
Lists all patterns available for installation on your system.
Package Groups
Lists all packages sorted by groups such as Graphics, Programming, or Security.
RPM Groups
Lists all packages sorted by functionality with groups and subgroups. For example
Networking > Email > Clients.
Languages
Filter to list all packages needed to add a new system language.
Repositories
Filter to list packages by repository. In order to select more than one repository,
hold the Ctrl key while clicking on repository names. The “pseudo repository”
@System lists all packages currently installed.
Search
Lets you search for a package according to certain criteria. Enter a search term
and press Enter. Refine your search by specifying where to Search In and by
changing the Search Mode. For example, if you do not know the package name
but only the name of the application that you are searching for, try including the
package Description in the search process.
Installation Summary
If you have already selected packages for installation, update or removal, this
view shows the changes that will be applied to your system as soon as you click
Accept. To filter for packages with a certain status in this view, activate or deactivate the respective check boxes. Hit Shift + F1 for details on the status flags.
TIP: Finding Packages not Belonging to an Active Repository
To list all packages that do not belong to an active repository, choose View >
Repositories > @System and then choose Secondary Filter > Unmaintained
Packages. This is useful, for example, if you have deleted a repository and
would like to make sure no packages from that repository remain installed.
198
Deployment Guide
9.2.2 Installing and Removing Packages
or Patterns
Certain packages are dependent on other packages, such as shared libraries. On the
other hand, some packages cannot coexist with others on the system. If possible,
YaST automatically resolves these dependencies or conflicts. If your choice results in
a dependency conflict that cannot be automatically solved, you need to solve it manually as described in Section 9.2.4, “Checking Software Dependencies” (page 202).
NOTE: Removal of Packages
When removing any packages, by default YaST only removes the selected
packages. If you want YaST to also remove any other packages that become
unneeded after removal of the specified package, select Options > Cleanup
when deleting packages.
1 Search for packages as described in Section 9.2.1, “Views for Searching Packages
or Patterns” (page 197).
2 The packages found are listed in the right pane. To install a package or remove it,
right-click it and choose Install or Delete. If the relevant option is not available,
check the package status indicated by the symbol in front of the package name—
hit Shift + F1 for help.
TIP: Applying an Action to All Packages Listed
To apply an action to all packages listed in the right pane, choose an action from Package > All in This List.
3 To install a pattern, right-click the pattern name and choose Install.
4 It is not possible to remove a pattern per se. Instead, select the packages of a pattern you want to remove and mark them for removal.
5 In order to select more packages, repeat the steps mentioned above.
6 Before applying your changes, you can review or modify them by clicking View >
Installation Summary. By default, all packages that will change status, are listed.
Installing or Removing Software
199
7 In order to revert the status for a package, right-click the package and select one
of the following entries: Keep if the package was scheduled to be deleted or updated, or Do Not Install if it was scheduled for installation. To abandon all changes and
close the Software Manager, click Cancel and Abandon
8 When you are finished, click Accept to apply your changes.
9 In case YaST found dependencies on other packages, a list of packages that have
additionally been chosen for installation, update or removal is presented. Click
Continue to accept them.
After all selected packages are installed, updated or removed, the YaST Software
Manager automatically terminates.
NOTE: Installing Source Packages
Installing source packages with YaST Software Manager is not possible at the moment. Use the command line tool zypper for this purpose.
For more information, see Section “Installing or Downloading Source
Packages” (Chapter 6, Managing Software with Command Line Tools, ↑Administration Guide).
9.2.3 Updating Packages
Instead of updating individual packages, you can also update all installed packages or
all packages from a certain repository. When mass updating packages, the following
aspects are generally considered:
• priorities of the repositories that provide the package,
• architecture of the package (for example, x86_64, i686, i586),
• version number of the package,
• package vendor.
Which of the aspects has the highest importance for choosing the update candidates
depends on the respective update option you choose.
1 To update all installed packages to the latest version, choose Package > All Packages > Update if Newer Version Available from the main menu.
200
Deployment Guide
All repositories are checked for possible update candidates, using the following
policy: YaST first tries to restrict the search to packages with the same architecture
and vendor like the installed one. If the search is positive, the “best” update candidate from those is selected according to the process below. However, if no comparable package of the same vendor can be found, the search is expanded to all packages with the same architecture. If still no comparable package can be found, all
packages are considered and the “best” update candidate is selected according to
the following criteria:
1. Repository priority: Prefer the package from the repository with the highest priority.
2. If more than one package results from this selection, choose the one with the
“best” architecture (best choice: matching the architecture of the installed one;
otherwise: x86_64 > i686 > i586).
If the resulting package has a higher version number than the installed one, the installed package will be updated and replaced with the selected update candidate.
This option tries to avoid changes in architecture and vendor for the installed packages, but under certain circumstances, they are tolerated.
NOTE: Update Unconditionally
If you choose Package > All Packages > Update Unconditionally instead,
basically the same criteria apply but any candidate package found is installed unconditionally. Thus, choosing this option might actually lead to
downgrading some packages.
2 To make sure that the packages for a mass update derive from a certain repository:
2a Choose the repository from which to update as described in Section 9.2.1,
“Views for Searching Packages or Patterns” (page 197).
2b On the right hand side of the window, click Switch system packages to the
versions in this repository. This explicitly allows YaST to change the package
vendor when replacing the packages.
As soon as you proceed with Accept, all installed packages will be replaced
by packages deriving from this repository, if available. This may lead to
Installing or Removing Software
201
changes in vendor and architecture and even to downgrading some packages.
2c To refrain from this, click Cancel switching system packages to the versions
in this repository. Note that you can only cancel this until you press the Accept button.
3 Before applying your changes, you can review or modify them by clicking View >
Installation Summary. By default, all packages that will change status, are listed.
4 If all options are set according to your wishes, confirm your changes with Accept to
start the mass update.
9.2.4 Checking Software Dependencies
Most packages are dependent on other packages. If a package, for example, uses a
shared library, it is dependent on the package providing this library. On the other hand
some packages cannot coexist with each other, causing a conflict (for example, you
can only install one mail transfer agent: sendmail or postfix). When installing or removing software, the Software Manager makes sure no dependencies or conflicts remain unsolved to ensure system integrity.
In case there exists only one solution to resolve a dependency or a conflict, it is resolved automatically. Multiple solutions always cause a conflict which needs to be resolved manually. If solving a conflict involves a vendor or architecture change, it also
needs to be solved manually. When clicking Accept to apply any changes in the Software Manager, you get an overview of all actions triggered by the automatic resolver
which you need to confirm.
By default, dependencies are automatically checked. A check is performed every time
you change a package status (for example, by marking a package for installation or removal). This is generally useful, but can become exhausting when manually resolving
a dependency conflict. To disable this function, uncheck Dependencies > Autocheck.
Manually perform a dependency check with Dependencies > Check Now. A consistency check is always performed when you confirm your selection with Accept.
To review a package's dependencies, right-click it and choose Show Solver Information. A map showing the dependencies opens. Packages that are already installed are
displayed in a green frame.
202
Deployment Guide
NOTE: Manually Solving Package Conflicts
Unless you are very experienced, follow the suggestions YaST makes when
handling package conflicts, otherwise you may not be able to resolve them.
Keep in mind that every change you make, potentially triggers other conflicts,
so you can easily end up with a steadily increasing number of conflicts. In
case this happens, Cancel the Software Manager, Abandon all your changes
and start again.
Figure 9.1: Conflict Management of the Software Manager
9.3 Managing Software
Repositories and Services
If you want to install third-party software, add additional software repositories to your
system. By default, the product repositories such as SUSE Linux Enterprise ServerDVD 11 SP4 and a matching update repository are automatically configured once
you have registered your system. For more information about registration, see Section 6.16.1.4, “Novell Customer Center Configuration” (page 125). Depending on the
initially selected product, a separate language add-on repository with translations, dictionaries, etc. might also be configured.
Installing or Removing Software
203
To manage repositories, start YaST and select Software > Software Repositories. The
Configured Software Repositories dialog opens. Here, you can also manage subscriptions to so-called Services by changing the View at the right corner of the dialog to All
Services. A Service in this context is a Repository Index Service (RIS) that can offer
one or more software repositories. Such a Service can be changed dynamically by its
administrator or vendor.
Each repository provides files describing content of the repository (package names,
versions, etc.). These repository description files are downloaded to a local cache that
is used by YaST. To ensure their integrity, software repositories can be signed with
the GPG Key of the repository maintainer. Whenever you add a new repository, YaST
offers the ability to import its key.
WARNING: Trusting External Software Sources
Before adding external software repositories to your list of repositories, make
sure this repository can be trusted. SUSE Linux Enterprise Server is not responsible for any potential problems arising from software installed from
third-party software repositories.
9.3.1 Adding Software Repositories
You can either add repositories from a local hard disk, from a removable medium
(like a CD, DVD or a USB mass storage) or from a network.
To add repositories from the Configured Software Repositories dialog in YaST proceed as follows:
1 Click Add.
2 From the list of available Media Types specify the type matching your repository:
For network sources, it is usually sufficient to use the default option, Specify URL.
To add a repository from a removable medium or a local hard disk, choose the relevant option and insert the medium or connect the USB device to the machine, respectively.
3 You can choose to Download Repository Description Files now. If the option is
unchecked, YaST will automatically download the files later, if needed. Click Next
to proceed.
204
Deployment Guide
4 When adding a repository from the network, enter the data you are prompted for.
Continue with Next.
5 Depending on the repository you have added, you might be asked if you want to
import the GPG key with which it is signed or asked to agree to a license.
After confirming these messages, YaST will download and parse the metadata and
add the repository to the list of Configured Repositories..
6 If needed, adjust the repository Properties as described in Section 9.3.2, “Managing
Repository Properties” (page 205) or confirm your changes with OK to close the
configuration dialog.
Now you can install software from this repository as described in Section 9.2, “Using
the KDE Interface (Qt)” (page 197).
9.3.2 Managing Repository Properties
The Configured Software Repositories overview of the Software Repositories lets you
change the following repository properties:
Status
The repository status can either be Enabled or Disabled. You can only install
packages from repositories that are enabled. To turn a repository off temporarily
click Disable. You can also double-click a repository name to toggle its status. If
you want to remove a repository completely, click Delete.
Refresh
When refreshing a repository, its content description (package names, versions,
etc.) is downloaded to a local cache that is used by YaST. It is sufficient to do this
once for static repositories such as CDs or DVDs, whereas repositories whose
content changes often should be refreshed frequently. The easiest way to keep a
repository's cache up-to-date is to choose Automatically Refresh. To do a manual
refresh click Refresh and select one of the options.
Keep Downloaded Packages
Packages from remote repositories are downloaded before being installed. By default, they are deleted upon a successful installation. Activating Keep Downloaded
Packages prevents the deletion of downloaded packages. The download location
is configured in /etc/zypp/zypp.conf, by default it is /var/cache/
zypp/packages.
Installing or Removing Software
205
Priority
The Priority of a repository is a value between 1 and 200, with 1 being the highest priority and 200 the lowest priority. Any new repositories that are added with
YaST get a priority of 99 by default. If you do not care about a priority value for
a certain repository, you can also set the value to 0 to apply the default priority to
that repository (99). If a package is available in more than one repository, then
the repository with the highest priority takes precedence. This is useful if you
want to avoid downloading packages unnecessarily from the Internet by giving a
local repository (for example, a DVD) a higher priority.
IMPORTANT: Priority vs. Version
The repository with the highest priority takes precedence in any case.
Therefore, make sure that the update repository always has the highest
priority (20 by default), otherwise you might install an outdated version
that will not be updated until the next online update.
Name and URL
To change a repository name or its URL, select it from the list with a single-click
and then click Edit.
9.3.3 Managing Repository Keys
To ensure their integrity, software repositories can be signed with the GPG Key of
the repository maintainer. Whenever you add a new repository, YaST offers to import its key. Verify it as you would do with any other GPG key and make sure it does
not change. If you detect a key change, something might be wrong with the repository. Disable the repository as an installation source until you know the cause of the key
change.
To manage all imported keys, click GPG Keys... in the Configured Software Repositories dialog. Select an entry with the mouse to show the key properties at the bottom of
the window. Add, Edit or Delete keys with a click on the respective buttons.
9.4 Keeping the System Up-to-date
Novell offers a continuous stream of software security patches for your product. The
update applet informs you about the availability of patches and lets you easily install
them with just a few clicks.
206
Deployment Guide
9.4.1 Using the KDE Software Updater
The Software Updater icon resides in the system tray of your panel depicting a gearwheel with a green arrow. To start Software Updater manually, choose System Settings
> SoftwareManagement > Software Updates from the main menu. Alternatively, press
Alt + F2 and enter kpk_update.
NOTE: Icon Visibility
The Software Updater icon is only visible in the system tray, if patches are
available. Hover over the icon to see the number of patches available.
9.4.1.1 Installing Patches
1 Whenever software updates are available, the applet icon appears in the panel.
Left-click the Software Updater icon to launch the Review and Update software
window.
2 Select a patch for installation by ticking its check box. Get detailed information on
a patch by clicking on its title. To select all available patches for installation, tick
the check box in the table header.
3 Click Apply to start the patch installation.
4 In case you have started the patch installation for the first time, you will be asked
to enter the root password twice in order to proceed. If you also check Remember
authorization you will never be asked again to provide the password.
5 The Additional Changes window showing an installation summary opens. Click
Continue to finish the installation.
Installing or Removing Software
207
Figure 9.2: KDE Software Updater
The YaST Online Update offers advanced features to customize the patch installation.
Please refer to Chapter 1, YaST Online Update (↑Administration Guide) for more information.
9.4.1.2 Configuring the KDE Software Updater
By default Software Updater checks for updates every 24 hours, notifies you when
patches are available and does not automatically install patches. These settings can be
changed with the Software Management settings. To open the Software Management
settings choose System Settings > Software Management > Settings from the main menu.
Alternatively, press Alt + F2 and enter kpk_settings. The settings for Software
Updater are available in the Update Settings section.
IMPORTANT: Patch Origin
The Software Management settings also allows you to configure the repositories (Origin of Packages) to be used. This setting not only applies to Software Updater but also to the KDE Software Management module (Get and
Remove Software).
Make sure the repository Updates for SUSE Linux Enterprise Server 11 SP4
is always selected—otherwise you will not receive patches.
208
Deployment Guide
9.4.2 Using the GNOME Update Applet
The update applet resides in the notification area of the panel. Its icon changes depending on the availability and relevance of patches and the status of the update. To
invoke the applet manually, choose Computer > More Applications > System > Software Update.
NOTE: Icon visibility
The applet icon is only visible if the following conditions are met:
• patches are available
• the GUI was not started as user root
• the GUI was not started in a VNC session
To start the update viewer even if no applet icon is visible, press Alt + F2 and
enter gpk-update-viewer.
Open box with a globe
The update applet is busy (for example checking for updates or installing software).
Red Star with Exclamation Mark
Security patches are available.
Orange Star with an Up Arrow
Important patches are available.
Yellow Star with a Down Arrow
Trivial patches are available.
Yellow Triangle with Exclamation Mark
An error has occurred.
9.4.2.1 Installing Patches
Procedure 9.1: Installing Patches
1 Whenever new patches are available, a notification message will appear and the
Update Applet icon will be visible in the notification area. Either click Install upInstalling or Removing Software
209
dates in the notification message or click the icon to open the Software Update
window.
2 All security and important patches are preselected. It is strongly recommended to
install these patches. Trivial patches can be manually selected by ticking the respective check boxes. Get detailed information on a patch by clicking on its title.
3 Click Install Updates to start the patch installation.
4 The Additional Confirmation Required window showing an installation summary
opens. Click Continue to proceed.
5 Enter the root password in the authentication screen and proceed with Authenticate.
Figure 9.3: GNOME Update Applet
The YaST Online Update offers advanced features to customize the patch installation.
Please refer to Chapter 1, YaST Online Update (↑Administration Guide) for more information.
210
Deployment Guide
9.4.2.2 Configuring the Software Update Applet
To configure the update applet, right-click the update icon in the panel and choose
Preferences. The configuration dialog lets you modify the following settings:
Check for Updates
Choose how often a check for updates is performed: Hourly, Daily, Weekly, or
Never.
Automatically Install
Configure whether patches are installed automatically or not (default). Automatic
installation can be chosen for either security patches only or for all patches.
Check for Major Upgrades
Choose how often a check for major upgrades is performed: Daily, Weekly, or
Never.
Check for updates when using mobile broadband
This configuration option is only available on mobile computers. Turned off by
default.
More options are configurable using gconf-editor: apps > gnome-packagekit.
Installing or Removing Software
211
Installing Add-On Products
Add-on products are system extensions. You can install a third party add-on product
or a special system extension of SUSE® Linux Enterprise Server (for example, a CD
with support for additional languages or a CD with binary drivers). To install a new
add-on, start YaST and select Software > Add-On Products . You can select various
types of product media, like CD, FTP, USB mass storage devices (such as USB flash
drives or disks) or a local directory. You can work also directly with ISO files. To add
an add-on as ISO file media, select Local ISO Image then enter the Path to ISO Image.
The Repository Name is arbitrary.
10
10.1 Add-Ons
To install a new add-on, proceed as follows:
1 In YaST select Software > Add-On Products to see an overview of already installed
add-on products.
2 To install a new add-on product, click Add.
3 From the list of available Media Types specify the type matching your repository.
4 To add a repository from a removable medium, choose the relevant option and insert the medium or connect the USB device to the machine, respectively.
5 You can choose to Download Repository Description Files now. If the option is
unchecked, YaST will automatically download the files later, if needed. Click Next
to proceed.
Installing Add-On Products
213
6 When adding a repository from the network, enter the data you are prompted for.
Continue with Next.
7 Depending on the repository you have added, you may be asked if you want to import the GPG key with which it is signed or asked to agree to a license.
After confirming these messages, YaST will download and parse the metadata and
add the repository to the list of Configured Repositories.
8 If needed, adjust the repository Properties as described in Section 9.3.2, “Managing
Repository Properties” (page 205) or confirm your changes with OK to close the
configuration dialog.
9 After having successfully added the repository for the add-on media, the software
manager starts and you can install packages. Refer to Chapter 9, Installing or Removing Software (page 195) for details.
10.2 Binary Drivers
Some hardware needs binary-only drivers to function properly. If you have such hardware, refer to the release notes for more information about availability of binary drivers for your system. To read the release notes, open YaST and select Miscellaneous >
Release Notes.
10.3 SUSE Software Development
Kit (SDK) 11
SUSE Software Development Kit 11 is an add-on for SUSE Linux Enterprise 11. It is
a complete tool kit for application development. In fact, to provide a comprehensive
build system, SUSE Software Development Kit 11 includes all the open source tools
that were used to build the SUSE Linux Enterprise Server product. It provides you as a developer, independent software vendor (ISV), or independent hardware vendor
(IHV) - with all the tools needed to port applications to all the platforms supported by
SUSE Linux Enterprise Desktop and SUSE Linux Enterprise Server.
SUSE Software Development Kit also contains integrated development environments
(IDEs), debuggers, code editors, and other related tools. It supports most major pro214
Deployment Guide
gramming languages, including C, C++, Java, and most scripting languages. For your
convenience, SUSE Software Development Kit includes multiple Perl packages that
are not included in SUSE Linux Enterprise.
Download SDK from http://download.suse.com/. Use the YaST add-on installer and package manager to install SUSE Software Development Kit 11.
Installing Add-On Products
215
Accessing the Internet
If you have chosen not to configure Internet access during the installation, you can
perform this task at any time using YaST. How to configure your computer to access
the Internet depends on your environment. If the computer you are installing is part
of a network which already is connected to the Internet, the only thing to do is to link
your machine to the network. If you are installing a machine that is directly connected to the Internet, the hardware and the access to the Internet Service Provider (ISP)
needs to be set up.
11
Please refer to the checklists below to make sure you have all the necessary data ready
before starting to configure the Internet access.
11.1 Direct Internet Connection
When your computer is directly connected to the Internet, you first need to configure
the hardware that is used for this task. This can either be an internal device (such as
an ISDN card) or an external device (for example, a modem). In most cases it is detected automatically.
Next, you need to enter the data provided by your ISP (such as login credentials, gateway, or name server, for example). You should have received a data sheet from your
ISP where all the necessary data is listed.
If you have successfully configured your hardware and ISP data, use the NetworkManager for managing the internet connection. See Chapter 27, Using NetworkManager (↑Administration Guide) for details.
Accessing the Internet
217
11.1.1 Checklist DSL
There are different types of DSL devices available that use different point-to-point
protocol (PPP) methods:
• a regular ethernet card connected to the external DSL modem uses PPP over Ethernet (PPPoE). In Austria the Point-to-Point Tunneling Protocol (PPTP) is used.
With PPTP the external modem also has a static IP address.
• an internal DSL modem uses PPP over ATM (PPPoATM)
• an internal ADSL Fritz Card uses CAPI for ADSL
The DSL configuration module already contains the data for major ISPs in some
countries. If your ISP is not listed, you will need to know how name resolving (DNS)
and IP allocation is handled (in most cases this data is received automatically when
connecting). Regardless whether you choose an ISP from the list or add a custom
provider, you need to enter at least your login and password.
For configuration details, refer to Section “DSL” (Chapter 22, Basic Networking, ↑Administration Guide).
11.1.2 Checklist ISDN
In case your internal ISDN card is not detected automatically you will need to know
the vendor and the name of the device.
NOTE: ISDN Modem or Terminal Adapter
If you are using an external ISDN modem or terminal adapter, refer to Section 11.1.3, “Checklist Modem” (page 219) instead.
In order to configure the ISDN device you will need the following data:
• ISDN Protocol (depends on your country)
• Area code and phone number.
• Interface type (SyncPPP or RawIP). If unsure, select SyncPPP, because RawIP is
only used in connection with certain telephone systems.
218
Deployment Guide
• Local and remote IP addresses for the dial-in server and the gateway, in the case
that you were given a static IP address from your provider.
• The ISDN configuration module already contains the data for major ISPs in some
countries. If your ISP is not listed, you will need to know how name resolving
(DNS) and IP allocation is handled (in most cases this data is received automatically when connecting). Regardless whether you chose an ISP from the list or added a
custom provider, you need to enter at least your login and password.
For configuration details, refer to Section “ISDN” (Chapter 22, Basic Networking,
↑Administration Guide).
11.1.3 Checklist Modem
If your modem is not detected automatically, you will need to know whether it is connected to a serial port or to a USB port. Please note that not all USB modems and internal modems are supported by SUSE® Linux Enterprise Server.
The modem configuration module already contains the data for major ISPs in some
countries. If your ISP is not listed, you will need to know its dial-in number and how
name resolving (DNS) and IP allocation is handled (in most cases this data is received
automatically when connecting). Regardless whether you chose an ISP from the list or
added a custom provider, you need to enter at least your login and password.
For configuration details, refer to Section “Modem” (Chapter 22, Basic Networking,
↑Administration Guide).
11.1.4 Checklist Cable Modem
Accessing the Internet through the TV cable requires a cable modem. Such a modem is connected to the computer via ethernet cable. Therefore it is only necessary
to configure your network card accordingly. For details, refer to Section “Cable
Modem” (Chapter 22, Basic Networking, ↑Administration Guide).
11.2 Internet Connection Via
Network
Accessing the Internet
219
If your machine is part of a network which is already connected to the Internet, it
is very easy to gain Internet access (just configure your network card and connect
your machine to the existing network and you are done). This not only applies to large
company networks, but to small home networks as well. Even if the machine you are
installing is only connected to a router (e.g. a DSL router) it is already part of a network. It is irrelevant whether you are using a wireless network adapter or a wired one.
NOTE: Routing and Name Services
In the following it is assumed that the network is connected to the Internet
and provides routing and name services. In case these services are provided
by a router, make sure the router is configured correctly before setting up the
client.
11.2.1 Checklist Network
If your network provides DHCP (Dynamic Host Configuration Protocol) check the
appropriate check box when setting up the network card and you are done (all parameters needed will be provided by the DHCP server).
If DHCP is not available, ask your network administrator for the following details:
• Hostname
• Name server
• Gateway
For configuration details for wired network cards, refer to Section “Configuring the
Network Card with YaST” (Chapter 22, Basic Networking, ↑Administration Guide), for
wireless network cards see Section “Configuration with YaST” (Chapter 19, Wireless
LAN, ↑Administration Guide).
220
Deployment Guide
Managing Users with YaST
12
During installation, you chose a method for user authentication. This method is either
local (via /etc/passwd) or, if a network connection is established, via NIS, LDAP,
Kerberos or Samba (see Section 6.16.1.7, “User Authentication Method” (page 130).
You can create or modify user accounts and change the authentication method with
YaST at any time.
Every user is assigned a system-wide user ID (UID). Apart from the users which can
log in to your machine, there are also a number of system users for internal use only. Each user is assigned to one or more groups. Similar to system users, there are also
system groups for internal use.
12.1 User and Group
Administration Dialog
To administer users or groups, start YaST and click Security and Users > User and
Group Management. Alternatively, start the User and Group Administration dialog directly by running yast2 users & from a command line.
Managing Users with YaST
221
Figure 12.1: YaST User and Group Administration
Depending on the set of users you choose to view and modify with, the dialog (local
users, network users, system users), the main window shows several tabs. These allow
you to execute the following tasks:
Managing User Accounts
From the Users tab create, modify, delete or temporarily disable user accounts as
described in Section 12.2, “Managing User Accounts” (page 223). Learn about
advanced options like enforcing password policies, using encrypted home directories, using fingerprint authentication, or managing disk quotas in Section 12.3,
“Additional Options for User Accounts” (page 225).
Changing Default Settings
Local users accounts are created according to the settings defined on the Defaults
for New Users tab. Learn how to change the default group assignment, or the default path and access permissions for home directories in Section 12.4, “Changing
Default Settings for Local Users” (page 232).
222
Deployment Guide
Assigning Users to Groups
Learn how to change the group assignment for individual users in Section 12.5,
“Assigning Users to Groups” (page 232).
Managing Groups
From the Groups tab, you can add, modify or delete existing groups. Refer to
Section 12.6, “Managing Groups” (page 233) for information on how to do
this.
Changing the User Authentication Method
When your machine is connected to a network that provides user authentication methods like NIS or LDAP, you can choose between several authentication
methods on the Authentication Settings tab. For more information, refer to Section 12.7, “Changing the User Authentication Method” (page 234).
For user and group management, the dialog provides similar functionality. You can
easily switch between the user and group administration view by choosing the appropriate tab at the top of the dialog.
Filter options allow you to define the set of users or groups you want to modify: On
the Users or Group tab, click Set Filter to view and edit users or groups according to
certain categories, such as Local Users or LDAP Users, for instance (if you are part of
a network which uses LDAP). With Set Filter > Customize Filter you can also set up
and use a custom filter.
Depending on the filter you choose, not all of the following options and functions will
be available from the dialog.
12.2 Managing User Accounts
YaST offers to create, modify, delete or temporarily disable user accounts. Do not
modify user accounts unless you are an experienced user or administrator.
NOTE: Changing User IDs of Existing Users
File ownership is bound to the user ID, not to the username. After a user ID
change, the files in the user's home directory are automatically adjusted to
reflect this change. However, after an ID change, the user no longer owns
Managing Users with YaST
223
the files he created elsewhere in the file system unless the file ownership for
those files are manually modified.
In the following, learn how to set up default user accounts. For some further options,
such as auto login, login without password, setting up encrypted home directories or
managing quotas for users and groups, refer to Section 12.3, “Additional Options for
User Accounts” (page 225).
Procedure 12.1: Adding or Modifying User Accounts
1 Open the YaST User and Group Administration dialog and click the Users tab.
2 With Set Filter define the set of users you want to manage. The dialog shows a list
of users in the system and the groups the users belong to.
3 To modify options for an existing user, select an entry and click Edit.
To create a new user account, click Add.
4 Enter the appropriate user data on the first tab, such as Username (which is used
for login) and Password. This data is sufficient to create a new user. If you click
OK now, the system will automatically assign a user ID and set all other values according to the default.
5 If you want to adjust further details such as the user ID or the path to the user's
home directory, do so on the Details tab.
If you need to relocate the home directory of an existing user, enter the path to the
new home directory there and move the contents of the current home directory
with Move to New Location. Otherwise, a new home directory is created without
any of the existing data.
6 To force users to regularly change their password or set other password options,
switch to Password Settings and adjust the options. For more details, refer to Section 12.3.2, “Enforcing Password Policies” (page 226).
7 If all options are set according to your wishes, click OK.
8 Click Expert Options > Write Changes Now to save all changes without exiting the
User and Group Administration dialog. Click OK to close the administration dialog
224
Deployment Guide
and to save the changes. A newly added user can now log in to the system using the
login name and password you created.
TIP: Matching User IDs
For a new (local) user on a laptop which also needs to integrate into a network environment where this user already has a user ID, it is useful to match
the (local) user ID to the ID in the network. This ensures that the file ownership of the files the user creates “offline” is the same as if he had created
them directly on the network.
Procedure 12.2: Disabling or Deleting User Accounts
1 Open the YaST User and Group Administration dialog and click the Users tab.
2 To temporarily disable a user account without deleting it, select the user from the
list and click Edit. Activate Disable User Login. The user cannot log in to your machine until you enable the account again.
3 To delete a user account, select the user from the list and click Delete. Choose if
you also want to delete the user's home directory or if you want to retain the data.
12.3 Additional Options for User
Accounts
In addition to the settings for a default user account, SUSE® Linux Enterprise Server offers further options, such as options to enforce password policies, use encrypted
home directories or define disk quotas for users and groups.
12.3.1 Automatic Login and Passwordless
Login
If you use the KDE or GNOME desktop environment you can configure Auto Login
for a certain user as well as Passwordless Login for all users. Auto login causes a user
to become automatically logged in to the desktop environment on boot. This functionality can only be activated for one user at a time. Login without password allows all
Managing Users with YaST
225
users to log in to the system after they have entered their username in the login manager.
WARNING: Security Risk
Enabling Auto Login or Passwordless Login on a machine that can be accessed by more than one person is a security risk. Without the need to authenticate, any user can gain access to your system and your data. If your
system contains confidential data, do not use this functionality.
If you want to activate auto login or login without password, access these functions in
the YaST User and Group Administration with Expert Options > Login Settings.
12.3.2 Enforcing Password Policies
On any system with multiple users, it is a good idea to enforce at least basic password
security policies. Users should change their passwords regularly and use strong passwords that cannot easily be exploited. For local users, proceed as follows:
Procedure 12.3: Configuring Password Settings
1 Open the YaST User and Group Administration dialog and select the Users tab.
2 Select the user for which to change the password options and click Edit.
3 Switch to the Password Settings tab. The user's last password change is displayed
on the tab.
4 To make the user change his password at next login, activate Force Password
Change.
5 To enforce password rotation, set a Maximum Number of Days for the Same
Password and a Minimum Number of Days for the Same Password.
6 To remind the user to change his password before it expires, set a number of
Days before Password Expiration to Issue Warning.
7 To restrict the period of time the user can log in after his password has expired,
change the value in Days after Password Expires with Usable Login.
226
Deployment Guide
8 You can also specify a certain expiration date for the complete account. Enter
the Expiration Date in YYYY-MM-DD format. Note that this setting is not password related but rather applies to the account itself.
9 For more information about the options and about the default values, click Help.
10 Apply your changes with OK.
12.3.3 Managing Encrypted Home
Directories
To protect data in home directories against theft and hard disk removal, you can create encrypted home directories for users. These are encrypted with LUKS (Linux
Unified Key Setup), which results in an image and an image key being generated for
the user. The image key is protected with the user's login password. When the user
logs into the system, the encrypted home directory is mounted and the contents are
made available to the user.
NOTE: Fingerprint Reader Devices and Encrypted Home Directories
If you want to use a fingerprint reader device, you must not use encrypted
home directories. Otherwise logging in will fail, because decrypting during login is not possible in combination with an active fingerprint reader device.
With YaST, you can create encrypted home directories for new or existing users. To
encrypt or modify encrypted home directories of already existing users, you need to
know the user's current login password. By default, all existing user data is copied to
the new encrypted home directory, but it is not deleted from the unencrypted directory.
WARNING: Security Restrictions
Encrypting a user's home directory does not provide strong security from other users. If strong security is required, the system should not be physically
shared.
Find background information about encrypted home directories and which
actions to take for stronger security in Section “Using Encrypted Home
Directories” (Chapter 11, Encrypting Partitions and Files, ↑Security Guide).
Managing Users with YaST
227
Procedure 12.4: Creating Encrypted Home Directories
1 Open the YaST User and Group Management dialog and click the Users tab.
2 To encrypt the home directory of an existing user, select the user and click Edit.
Otherwise, click Add to create a new user account and enter the appropriate user
data on the first tab.
3 In the Details tab, activate Use Encrypted Home Directory. With Directory Size in
MB, specify the size of the encrypted image file to be created for this user.
4 Apply your settings with OK.
5 Enter the user's current login password to proceed if YaST prompts for it.
6 Click Expert Options > Write Changes Now to save all changes without exiting the
administration dialog. Click OK to close the administration dialog and save the
changes.
228
Deployment Guide
Procedure 12.5: Modifying or Disabling Encrypted Home Directories
Of course, you can also disable the encryption of a home directory or change the size
of the image file at any time.
1 Open the YaST User and Group Administration dialog in the Users view.
2 Select a user from the list and click Edit.
3 If you want to disable the encryption, switch to the Details tab and disable Use Encrypted Home Directory.
If you need to enlarge or reduce the size of the encrypted image file for this user,
change the Directory Size in MB.
4 Apply your settings with OK.
5 Enter the user's current login password to proceed if YaST prompts for it.
6 Click Expert Options > Write Changes Now to save all changes without exiting the
User and Group Administration dialog. Click OK to close the administration dialog
and to save the changes.
12.3.4 Using Fingerprint Authentication
If your system includes a fingerprint reader you can use biometric authentication in
addition to standard authentication via login and password. After registering their fingerprint, users can log in to the system either by swiping a finger on the fingerprint
reader or by typing in a password.
Fingerprints can be registered with YaST. Find detailed information about configuration and use of fingerprint authentication in Chapter 7, Using the Fingerprint Reader (↑Security Guide). For a list of supported devices, refer to http://
www.freedesktop.org/wiki/Software/fprint/libfprint.
12.3.5 Managing Quotas
To prevent system capacities from being exhausted without notification, system administrators can set up quotas for users or groups. Quotas can be defined for one or
Managing Users with YaST
229
more file systems and restrict the amount of disk space that can be used and the number of inodes (index nodes) that can be created there. Inodes are data structures on
a file system that store basic information about a regular file, directory, or other file
system object. They store all attributes of a file system object (like user and group
ownership, read, write, or execute permissions), except file name and contents.
SUSE Linux Enterprise Server allows usage of soft and hard quotas. Soft quotas
usually define a warning level at which users are informed that they are nearing their
limit, whereas hard quotas define the limit at which write requests are denied. Additionally, grace intervals can be defined that allow users or groups to temporarily violate their quotas by certain amounts.
Procedure 12.6: Enabling Quota Support for a Partition
In order to configure quotas for certain users and groups, you need to enable quota
support for the respective partition in the YaST Expert Partitioner first.
1 In YaST, select System > Partitioner and click Yes to proceed.
2 In the Expert Partitioner, select the partition for which to enable quotas and click
Edit.
3 Click Fstab Options and activate Enable Quota Support. If the quota package is
not already installed, it will be installed once you confirm the respective message
with Yes.
4 Confirm your changes and leave the Expert Partitioner.
Procedure 12.7: Setting Up Quotas for Users or Groups
Now you can define soft or hard quotas for specific users or groups and set time periods as grace intervals.
1 In the YaST User and Group Administration, select the user or the group you want
to set the quotas for and click Edit.
2 On the Plug-Ins tab, select the Manage User Quota entry and click Launch to open
the Quota Configuration dialog.
3 From File System, select the partition to which the quota should apply.
230
Deployment Guide
4 Below Size Limits, restrict the amount of disk space. Enter the number of 1 KB
blocks the user or group may have on this partition. Specify a Soft Limit and a
Hard Limit value.
5 Additionally, you can restrict the number of inodes the user or group may have on
the partition. Below Inodes Limits, enter a Soft Limit and Hard Limit.
6 You can only define grace intervals if the user or group has already exceeded the
soft limit specified for size or inodes. Otherwise, the time-related input fields are
not activated. Specify the time period for which the user or group is allowed to exceed the limits set above.
7 Confirm your settings with OK.
8 Click Expert Options > Write Changes Now to save all changes without exiting the
User and Group Administration dialog. Click OK to close the administration dialog
and to save the changes.
SUSE Linux Enterprise Server also ships command line tools like repquota or
warnquota with which system administrators can control the disk usage or send eManaging Users with YaST
231
mail notifications to users exceeding their quota. With quota_nld, administrators
can also forward kernel messages about exceeded quotas to D-BUS. For more information, refer to the repquota, the warnquota and the quota_nld man page.
12.4 Changing Default Settings for
Local Users
When creating new local users, several default settings are used by YaST. These include, for example, the primary group and the secondary groups the user belongs to,
or the access permissions of the user's home directory. You can change these default
settings to meet your requirements:
1 Open the YaST User and Group Administration dialog and select the Defaults for
New Users tab.
2 To change the primary group the new users should automatically belong to, select
another group from Default Group.
3 To modify the secondary groups for new users, add or change groups in Secondary
Groups. The group names must be separated by commas.
4 If you do not want to use /home/username as default path for new users' home
directories, modify the Path Prefix for Home Directory.
5 To change the default permission modes for newly created home directories, adjust the umask value in Umask for Home Directory. For more information about
umask, refer to Chapter 10, Access Control Lists in Linux (↑Security Guide) and to
the umask man page.
6 For information about the individual options, click Help.
7 Apply your changes with OK.
12.5 Assigning Users to Groups
Local users are assigned to several groups according to the default settings which you
can access from the User and Group Administration dialog on the Defaults for New
232
Deployment Guide
Users tab. In the following, learn how to modify an individual user's group assignment. If you need to change the default group assignments for new users, refer to Section 12.4, “Changing Default Settings for Local Users” (page 232).
Procedure 12.8: Changing a User's Group Assignment
1 Open the YaST User and Group Administration dialog and click the Users tab. It
shows a list of users and of the groups the users belong to.
2 Click Edit and switch to the Details tab.
3 To change the primary group the user belongs to, click Default Group and select
the group from the list.
4 To assign the user additional secondary groups, activate the corresponding check
boxes in the Additional Groups list.
5 Click OK to apply your changes.
6 Click Expert Options > Write Changes Now to save all changes without exiting the
User and Group Administration dialog. Click OK to close the administration dialog
and save the changes.
12.6 Managing Groups
With YaST you can also easily add, modify or delete groups.
Procedure 12.9: Creating and Modifying Groups
1 Open the YaST User and Group Management dialog and click the Groups tab.
2 With Set Filter define the set of groups you want to manage. The dialog shows a list
of groups in the system.
3 To create a new group, click Add.
4 To modify an existing group, select the group and click Edit.
5 In the following dialog, enter or change the data. The list on the right shows an
overview of all available users and system users which can be members of the
group.
Managing Users with YaST
233
6 To add existing users to a new group select them from the list of possible Group
Members by checking the corresponding box. To remove them from the group
uncheck the box.
7 Click OK to apply your changes.
8 Click Expert Options > Write Changes Now to save all changes without exiting the
User and Group Administration dialog.
In order to delete a group, it must not contain any group members. To delete a group,
select it from the list and click Delete. Click Expert Options > Write Changes Now to
save all changes without exiting the User and Group Administration dialog. Click OK
to close the administration dialog and to save the changes.
12.7 Changing the User
Authentication Method
When your machine is connected to a network, you can change the authentication
method you set during installation. The following options are available:
234
Deployment Guide
NIS
Users are administered centrally on a NIS server for all systems in the network.
For details, see Chapter 3, Using NIS (↑Security Guide).
LDAP
Users are administered centrally on an LDAP server for all systems in the network. For details about LDAP, see Chapter 4, LDAP—A Directory Service (↑Security Guide).
You can manage LDAP users with the YaST user module. All other LDAP settings, including the default settings for LDAP users, have to be defined with the
YaST LDAP client module as described in Section “Configuring an LDAP Client
with YaST” (Chapter 4, LDAP—A Directory Service, ↑Security Guide) .
Kerberos
With Kerberos, a user registers once and then is trusted in the entire network for
the rest of the session.
Samba
SMB authentication is often used in mixed Linux and Windows networks. For details, see Chapter 28, Samba (↑Administration Guide).
eDirectory LDAP
eDirectory authentication is used in Novell networks.
To change the authentication method, proceed as follows:
1 Open the User and Group Administration dialog in YaST.
2 Click the Authentication Settings tab to show an overview of the available authentication methods and the current settings.
3 To change the authentication method, click Configure and select the authentication method you want to modify. This takes you directly to the client configuration modules in YaST. For information about the configuration of the appropriate
client, refer to the following sections:
NIS: Section “Configuring NIS Clients” (Chapter 3, Using NIS, ↑Security Guide)
LDAP: Section “Configuring an LDAP Client with YaST” (Chapter 4, LDAP—A
Directory Service, ↑Security Guide)
Managing Users with YaST
235
Samba: Section “Configuring a Samba Client with YaST” (Chapter 28, Samba,
↑Administration Guide)
4 After accepting the configuration, return to the User and Group Administration
overview.
5 Click OK to close the administration dialog.
236
Deployment Guide
Changing Language and
Country Settings with YaST
13
Working in different countries or having to work in a multilingual environment requires your computer to be set up to support this. SUSE® Linux Enterprise Server
can handle different locales in parallel. A locale is a set of parameters that defines
the language and country settings reflected in the user interface.
The main system language was selected during installation and keyboard and time
zone settings were adjusted. However, you can install additional languages on your
system and determine which of the installed languages should be the default.
For those tasks, use the YaST language module as described in Section 13.1, “Changing the System Language” (page 238). Install secondary languages to get optional
localizations if you need to start applications or desktops in languages other than the
primary one.
Apart from that, the YaST timezone module allows you to adjust your country and
timezone settings accordingly. It also lets you synchronize your system clock against
a time server. For details, refer to Section 13.2, “Changing the Country and Time
Settings” (page 242).
Changing Language and Country Settings with YaST
237
13.1 Changing the System
Language
Depending on how you use your desktop and whether you want to switch the entire
system to another language or just the desktop environment itself, there are several
ways to achieve this:
Changing the System Language Globally
Proceed as described in Section 13.1.1, “Modifying System Languages with
YaST” (page 238) and Section 13.1.2, “Switching the Default System
Language” (page 241) to install additional localized packages with YaST and
to set the default language. Changes are effective after relogin. To ensure that the
entire system reflects the change, reboot the system or close and restart all running services, applications, and programs.
Changing the Language for the Desktop Only
Provided you have previously installed the desired language packages for your
desktop environment with YaST as described below, you can switch the language
of your desktop using the desktop's control center. After the X server has been
restarted, your entire desktop reflects your new choice of language. Applications
not belonging to your desktop framework are not affected by this change and may
still appear in the language that was set in YaST.
Temporarily Switching Languages for One Application Only
You can also run a single application in another language (that has already been
installed with YaST). To do so, start it from the command line by specifying the
language code as described in Section 13.1.3, “Switching Languages for Individual Applications” (page 241).
13.1.1 Modifying System Languages with
YaST
YaST knows two different language categories:
Primary Language
The primary language set in YaST applies to the entire system, including YaST
and the desktop environment. This language is used whenever available unless
you manually specify another language.
238
Deployment Guide
Secondary Languages
Install secondary languages to make your system multilingual. Languages installed
as secondary languages can be selected manually for a specific situation. For example, use a secondary language to start an application in a certain language in order to do word processing in this language.
Before installing additional languages, determine which of them should be the default
system language (primary language) after you have installed them.
To access the YaST language module, start YaST and click System > Language. Alternatively, start the Languages dialog directly by running yast2 language & as
user root from a command line.
Procedure 13.1: Installing Additional Languages
When installing additional languages, YaST also allows you to set different locale
settings for the user root, see Step 4 (page 240). The option Locale Settings for
Changing Language and Country Settings with YaST
239
User root determines how the locale variables (LC_*) in the file /etc/syscon​
fig/language are set for root. You can either set them to the same locale as
for normal users, keep it unaffected by any language changes or only set the variable
RC_LC_CTYPE to the same values as for the normal users. This variable sets the localization for language-specific function calls.
1 To add additional languages in the YaST language module, select the Secondary
Languages you wish to install.
2 To make a language the default language, set it as Primary Language.
3 Additionally, adapt the keyboard to the new primary language and adjust the time
zone, if appropriate.
TIP
For advanced keyboard or time zone settings, select Hardware > Keyboard Layout or System > Date and Time in YaST to start the respective
dialogs. For more information, refer to Section 13.2, “Changing the Country and Time Settings” (page 242).
4 To change language settings specific to the user root, click Details.
4a Set Locale Settings for User root to the desired value. For more information,
click Help.
4b Decide if you want to Use UTF-8 Encoding for root or not.
5 If your locale was not included in the list of primary languages available, try specifying it with Detailed Locale Setting. However, some of these localizations may be
incomplete.
6 Confirm your changes in the dialogs with OK. If you have selected secondary languages, YaST installs the localized software packages for the additional languages.
The system is now multilingual. However, to start an application in a language other
than the primary one, you need to set the desired language explicitly as explained in
Section 13.1.3, “Switching Languages for Individual Applications” (page 241).
240
Deployment Guide
13.1.2 Switching the Default System
Language
1 To globally switch the default system language, start the YaST language module.
2 Select the desired new system language as Primary Language.
IMPORTANT: Deleting Former System Languages
If you switch to a different primary language, the localized software packages for the former primary language will be removed from the system. If
you want to switch the default system language but want to keep the former primary language as additional language, add it as Secondary Language by enabling the respective check box.
3 Adjust the keyboard and time zone options as desired.
4 Confirm your changes with OK.
5 After YaST has applied the changes, restart any X sessions (for example, by logging out and logging in again) to make YaST and the desktop applications reflect
your new language settings.
13.1.3 Switching Languages for Individual
Applications
After you have installed the respective language with YaST, you can run a single application in another language.
Standard X and GNOME Applications
Start the application from the command line by using the following command:
LANG=language application
For example, to start f-spot in German, run LANG=de_DE f-spot. For other languages, use the appropriate language code. Get a list of all language codes
available with the locale -av command.
Changing Language and Country Settings with YaST
241
KDE Applications
Start the application from the command line by using the following command:
KDE_LANG=language application
For example, to start digiKam in German, run KDE_LANG=de digikam. For
other languages, use the appropriate language code.
13.2 Changing the Country and
Time Settings
Using the YaST date and time module, adjust your system date, clock and time zone
information to the area you are working in. To access the YaST module, start YaST
and click System > Date and Time. Alternatively, start the Clock and Time Zone dialog
directly by running yast2 timezone & as user root from a command line.
First, select a general region, such as Europe. Choose an appropriate country that
matches the one you are working in, for example, Germany.
242
Deployment Guide
Depending on which operating systems run on your workstation, adjust the hardware
clock settings accordingly:
• If you run another operating system on your machine, such as Microsoft Windows*, it is likely your system does not use UTC, but local time. In this case,
uncheck Hardware Clock Set To UTC.
• If you only run Linux on your machine, set the hardware clock to UTC and have
the switch from standard time to daylight saving time performed automatically.
You can change the date and time manually or opt for synchronizing your machine
against an NTP server, either permanently or just for adjusting your hardware clock.
Procedure 13.2: Manually Adjusting Time and Date
1 In the YaST timezone module, click Change to set date and time.
2 Select Manually and enter date and time values.
3 Confirm your changes with Accept.
Procedure 13.3: Setting Date and Time With NTP Server
1 Click Change to set date and time.
2 Select Synchronize with NTP Server.
3 Enter the address of an NTP server, if not already populated.
Changing Language and Country Settings with YaST
243
4 Click Synchronize Now, to get your system time set correctly.
5 If you want to make use of NTP permanently, enable Save NTP Configuration.
6 With the Configure button, you can open the advanced NTP configuration. For details, see Section “Configuring an NTP Client with YaST” (Chapter 24, Time Synchronization with NTP, ↑Administration Guide).
7 Confirm your changes with Accept.
244
Deployment Guide
Remote Installation
SUSE® Linux Enterprise Server can be installed in different ways. As well as the usual media installation covered in Chapter 6, Installation with YaST (page 93), you can
choose from various network-based approaches or even take a completely hands-off
approach to the installation of SUSE Linux Enterprise Server.
14
Each method is introduced by means of two short checklists: one listing the prerequisites for this method and the other illustrating the basic procedure. More detail is then
provided for all the techniques used in these installation scenarios.
NOTE
In the following sections, the system to hold your new SUSE Linux Enterprise
Server installation is referred to as target system or installation target. The
term repository (previously called “installation source”) is used for all sources
of installation data. This includes physical media, such as CD and DVD, and
network servers distributing the installation data in your network.
14.1 Installation Scenarios for
Remote Installation
This section introduces the most common installation scenarios for remote installations. For each scenario, carefully check the list of prerequisites and follow the procedure outlined for this scenario. If in need of detailed instructions for a particular step,
follow the links provided for each one of them.
Remote Installation
245
IMPORTANT
The configuration of the X Window System is not part of any remote installation process. After the installation has finished, log in to the target system
as root, enter telinit 3, and start SaX2 to configure the graphics hardware.
14.1.1 Simple Remote Installation via
VNC—Static Network Configuration
This type of installation still requires some degree of physical access to the target system to boot for installation. The installation itself is entirely controlled by a remote
workstation using VNC to connect to the installation program. User interaction is required as with the manual installation in Chapter 6, Installation with YaST (page 93).
For this type of installation, make sure that the following requirements are met:
• Remote repository: NFS, HTTP, FTP, TFTP, or SMB with working network connection.
• Target system with working network connection.
• Controlling system with working network connection and VNC viewer software or
Java-enabled browser (Firefox, Konqueror, Internet Explorer, Opera, etc.).
• Physical boot medium (CD, DVD, or USB flash drive) for booting the target system.
• Valid static IP addresses already assigned to the repository and the controlling system.
• Valid static IP address to assign to the target system.
• When installing over VNC, X11 is not configured and output is redirected to your
local machine. To use SaX2, use export DISPLAY=:0 && sax2 -a -r
To perform this kind of installation, proceed as follows:
1 Set up the repository as described in Section 14.2, “Setting Up the Server Holding
the Installation Sources” (page 254). Choose an NFS, HTTP, FTP, or TFTP net246
Deployment Guide
work server. For an SMB repository, refer to Section 14.2.5, “Managing an SMB
Repository” (page 261).
2 Boot the target system using DVD1 of the SUSE Linux Enterprise Server media
kit.
3 When the boot screen of the target system appears, use the boot options
prompt to set the appropriate VNC options and the address of the repository. This is described in detail in Section 14.4, “Booting the Target System for
Installation” (page 274).
The target system boots to a text-based environment, giving the network address
and display number under which the graphical installation environment can be addressed by any VNC viewer application or browser. VNC installations announce
themselves over OpenSLP and if the firewall settings permit, they can be found using Konqueror in service:/ or slp:/ mode.
4 On the controlling workstation, open a VNC viewing application or Web browser and connect to the target system as described in Section 14.5.1, “VNC
Installation” (page 278).
5 Perform the installation as described in Chapter 6, Installation with YaST (page 93).
Reconnect to the target system after it reboots for the final part of the installation.
6 Finish the installation.
14.1.2 Simple Remote Installation via
VNC—Dynamic Network Configuration
This type of installation still requires some degree of physical access to the target system to boot for installation. The network configuration is made with DHCP. The installation itself is entirely controlled from a remote workstation using VNC to connect
to the installer, but still requires user interaction for the actual configuration efforts.
For this type of installation, make sure that the following requirements are met:
• Remote repository: NFS, HTTP, FTP, or SMB with working network connection.
• Target system with working network connection.
Remote Installation
247
• Controlling system with working network connection and VNC viewer software or
Java-enabled browser (Firefox, Konqueror, Internet Explorer, or Opera).
• Boot the target system using DVD1 of the SUSE Linux Enterprise Server media
kit.
• Running DHCP server providing IP addresses.
• When installing over VNC, X11 is not configured and output is redirected to your
local machine. To use SaX2, use export DISPLAY=:0 && sax2 -a -r
To perform this kind of installation, proceed as follows:
1 Set up the repository as described in Section 14.2, “Setting Up the Server Holding the Installation Sources” (page 254). Choose an NFS, HTTP, or FTP network server. For an SMB repository, refer to Section 14.2.5, “Managing an SMB
Repository” (page 261).
2 Boot the target system using DVD1 of the SUSE Linux Enterprise Server media
kit.
3 When the boot screen of the target system appears, use the boot options
prompt to set the appropriate VNC options and the address of the repository. This is described in detail in Section 14.4, “Booting the Target System for
Installation” (page 274).
The target system boots to a text-based environment, giving the network address
and display number under which the graphical installation environment can be addressed by any VNC viewer application or browser. VNC installations announce
themselves over OpenSLP and if the firewall settings permit, they can be found using Konqueror in service:/ or slp:/ mode.
4 On the controlling workstation, open a VNC viewing application or Web browser and connect to the target system as described in Section 14.5.1, “VNC
Installation” (page 278).
5 Perform the installation as described in Chapter 6, Installation with YaST (page 93).
Reconnect to the target system after it reboots for the final part of the installation.
6 Finish the installation.
248
Deployment Guide
14.1.3 Remote Installation via VNC—PXE
Boot and Wake on LAN
This type of installation is completely hands-off. The target machine is started and
booted remotely. User interaction is only needed for the actual installation. This approach is suitable for cross-site deployments.
To perform this type of installation, make sure that the following requirements are
met:
• Remote repository: NFS, HTTP, FTP, or SMB with working network connection.
• TFTP server.
• Running DHCP server for your network.
• Target system capable of PXE boot, networking, and Wake on LAN, plugged in
and connected to the network.
• Controlling system with working network connection and VNC viewer software or
Java-enabled browser (Firefox, Konqueror, Internet Explorer, or Opera).
• When installing over VNC, X11 is not configured and output is redirected to your
local machine. To use SaX2, use export DISPLAY=:0 && sax2 -a -r
To perform this type of installation, proceed as follows:
1 Set up the repository as described in Section 14.2, “Setting Up the Server Holding
the Installation Sources” (page 254). Choose an NFS, HTTP, or FTP network
server or configure an SMB repository as described in Section 14.2.5, “Managing
an SMB Repository” (page 261).
2 Set up a TFTP server to hold a boot image that can be pulled by the target system.
This is described in Section 14.3.2, “Setting Up a TFTP Server” (page 265).
3 Set up a DHCP server to provide IP addresses to all machines and reveal the location of the TFTP server to the target system. This is described in Section 14.3.1,
“Setting Up a DHCP Server” (page 263).
4 Prepare the target system for PXE boot. This is described in further detail in Section 14.3.5, “Preparing the Target System for PXE Boot” (page 273).
Remote Installation
249
5 Initiate the boot process of the target system using Wake on LAN. This is described in Section 14.3.7, “Wake on LAN” (page 273).
6 On the controlling workstation, open a VNC viewing application or Web browser and connect to the target system as described in Section 14.5.1, “VNC
Installation” (page 278).
7 Perform the installation as described in Chapter 6, Installation with YaST (page 93).
Reconnect to the target system after it reboots for the final part of the installation.
8 Finish the installation.
14.1.4 Simple Remote Installation via
SSH—Static Network Configuration
This type of installation still requires some degree of physical access to the target system to boot for installation and to determine the IP address of the installation target.
The installation itself is entirely controlled from a remote workstation using SSH to
connect to the installer. User interaction is required as with the regular installation described in Chapter 6, Installation with YaST (page 93).
For this type of installation, make sure that the following requirements are met:
• Remote repository: NFS, HTTP, FTP, or SMB with working network connection.
• Target system with working network connection.
• Controlling system with working network connection and working SSH client software.
• Boot the target system using DVD1 of the SUSE Linux Enterprise Server media
kit.
• Valid static IP addresses already assigned to the repository and the controlling system.
• Valid static IP address to assign to the target system.
• When installing over SSH, X11 is not configured and output is redirected to your
local machine. To use SaX2, use export DISPLAY=:0 && sax2 -a -r
To perform this kind of installation, proceed as follows:
250
Deployment Guide
1 Set up the repository as described in Section 14.2, “Setting Up the Server Holding the Installation Sources” (page 254). Choose an NFS, HTTP, or FTP network server. For an SMB repository, refer to Section 14.2.5, “Managing an SMB
Repository” (page 261).
2 Boot the target system using DVD1 of the SUSE Linux Enterprise Server media
kit.
3 When the boot screen of the target system appears, use the boot options prompt to
set the appropriate parameters for network connection, address of the repository,
and SSH enablement. This is described in detail in Section 14.4.2, “Using Custom
Boot Options” (page 275).
The target system boots to a text-based environment, giving the network address
under which the graphical installation environment can be addressed by any SSH
client.
4 On the controlling workstation, open a terminal window and connect to the
target system as described in Section 14.5.2.2, “Connecting to the Installation
Program” (page 280).
5 Perform the installation as described in Chapter 6, Installation with YaST (page 93).
Reconnect to the target system after it reboots for the final part of the installation.
6 Finish the installation.
14.1.5 Simple Remote Installation via
SSH—Dynamic Network Configuration
This type of installation still requires some degree of physical access to the target system to boot for installation and determine the IP address of the installation target. The
installation itself is entirely controlled from a remote workstation using SSH to connect to the installer, but still requires user interaction for the actual configuration efforts.
NOTE: Avoid Lost Connections After 2nd Step (Installation)
In the network settings dialog, check the Traditional Method with ifup and
avoid NetworkManager. If not, your SSH connection will be lost during instalRemote Installation
251
lation. Reset the settings to User Controlled with NetworkManager after your
installation has finished.
For this type of installation, make sure that the following requirements are met:
• Remote repository: NFS, HTTP, FTP, or SMB with working network connection.
• Target system with working network connection.
• Controlling system with working network connection and working SSH client software.
• Physical boot medium (CD, DVD, or USB flash drive) for booting the target system.
• Running DHCP server providing IP addresses.
• When installing over SSH, X11 is not configured and output is redirected to your
local machine. To use SaX2, use export DISPLAY=:0 && sax2 -a -r
To perform this kind of installation, proceed as follows:
1 Set up the repository source as described in Section 14.2, “Setting Up the Server
Holding the Installation Sources” (page 254). Choose an NFS, HTTP, or FTP
network server. For an SMB repository, refer to Section 14.2.5, “Managing an
SMB Repository” (page 261).
2 Boot the target system using DVD1 of the SUSE Linux Enterprise Server media
kit.
3 When the boot screen of the target system appears, use the boot options prompt
to pass the appropriate parameters for network connection, location of the installation source, and SSH enablement. See Section 14.4.2, “Using Custom Boot
Options” (page 275) for detailed instructions on the use of these parameters.
The target system boots to a text-based environment, giving you the network address under which the graphical installation environment can be addressed by any
SSH client.
4 On the controlling workstation, open a terminal window and connect to the
target system as described in Section 14.5.2.2, “Connecting to the Installation
Program” (page 280).
252
Deployment Guide
5 Perform the installation as described in Chapter 6, Installation with YaST (page 93).
Reconnect to the target system after it reboots for the final part of the installation.
6 Finish the installation.
14.1.6 Remote Installation via SSH—PXE
Boot and Wake on LAN
This type of installation is completely hands-off. The target machine is started and
booted remotely.
To perform this type of installation, make sure that the following requirements are
met:
• Remote repository: NFS, HTTP, FTP, or SMB with working network connection.
• TFTP server.
• Running DHCP server for your network, providing a static IP to the host to install.
• Target system capable of PXE boot, networking, and Wake on LAN, plugged in
and connected to the network.
• Controlling system with working network connection and SSH client software.
• When installing over SSH, X11 is not configured and output is redirected to your
local machine. To use SaX2, use export DISPLAY=:0 && sax2 -a -r
To perform this type of installation, proceed as follows:
1 Set up the repository as described in Section 14.2, “Setting Up the Server Holding
the Installation Sources” (page 254). Choose an NFS, HTTP, or FTP network
server. For the configuration of an SMB repository, refer to Section 14.2.5, “Managing an SMB Repository” (page 261).
2 Set up a TFTP server to hold a boot image that can be pulled by the target system.
This is described in Section 14.3.2, “Setting Up a TFTP Server” (page 265).
3 Set up a DHCP server to provide IP addresses to all machines and reveal the location of the TFTP server to the target system. This is described in Section 14.3.1,
“Setting Up a DHCP Server” (page 263).
Remote Installation
253
4 Prepare the target system for PXE boot. This is described in further detail in Section 14.3.5, “Preparing the Target System for PXE Boot” (page 273).
5 Initiate the boot process of the target system using Wake on LAN. This is described in Section 14.3.7, “Wake on LAN” (page 273).
6 On the controlling workstation, start an SSH client and connect to the target system
as described in Section 14.5.2, “SSH Installation” (page 279).
7 Perform the installation as described in Chapter 6, Installation with YaST (page 93).
Reconnect to the target system after it reboots for the final part of the installation.
8 Finish the installation.
14.2 Setting Up the Server Holding
the Installation Sources
Depending on the operating system running on the machine to use as the network installation source for SUSE Linux Enterprise Server, there are several options for the
server configuration. The easiest way to set up an installation server is to use YaST on
SUSE Linux Enterprise Server 11 SP4 or openSUSE 11.1 and higher.
TIP
You can even use a Microsoft Windows machine as the installation server for your Linux deployment. See Section 14.2.5, “Managing an SMB
Repository” (page 261) for details.
14.2.1 Setting Up an Installation Server
Using YaST
YaST offers a graphical tool for creating network repositories. It supports HTTP,
FTP, and NFS network installation servers.
1 Log in as root to the machine that should act as installation server.
2 Start YaST > Miscellaneous > Installation Server.
254
Deployment Guide
3 Select the repository type (HTTP, FTP, or NFS). The selected service is started automatically every time the system starts. If a service of the selected type is already
running on your system and you want to configure it manually for the server, deactivate the automatic configuration of the server service with Do Not Configure Any
Network Services. In both cases, define the directory in which the installation data
should be made available on the server.
4 Configure the required repository type. This step relates to the automatic configuration of server services. It is skipped when automatic configuration is deactivated.
Define an alias for the root directory of the FTP or HTTP server on which
the installation data should be found. The repository will later be located under ftp://Server-IP/Alias/Name (FTP) or under http://Server-IP/Alias/Name (HTTP). Name stands for the name of the repository,
which is defined in the following step. If you selected NFS in the previous step,
define wild cards and export options. The NFS server will be accessible under
nfs://Server-IP/Name. Details of NFS and exports can be found in Chapter 29, Sharing File Systems with NFS (↑Administration Guide).
TIP: Firewall Settings
Make sure that the firewall settings of your server system allow traffic on
the ports for HTTP, NFS, and FTP. If they currently do not, enable Open
Port in Firewall or check Firewall Details first.
5 Configure the repository. Before the installation media are copied to their destination, define the name of the repository (ideally, an easily remembered abbreviation of the product and version). YaST allows providing ISO images of the media instead of copies of the installation DVDs. If you want this, activate the relevant check box and specify the directory path under which the ISO files can be
found locally. Depending on the product to distribute using this installation server,
it might be that more add-on CDs or service pack CDs are required and should be
added as extra repositories. To announce your installation server in the network via
OpenSLP, activate the appropriate option.
TIP
Consider announcing your repository via OpenSLP if your network setup supports this option. This saves you from entering the network installation path on every target machine. The target systems are just booted usRemote Installation
255
ing the SLP boot option and find the network repository without any further
configuration. For details on this option, refer to Section 14.4, “Booting the
Target System for Installation” (page 274).
6 Upload the installation data. The most lengthy step in configuring an installation
server is copying the actual installation media. Insert the media in the sequence
requested by YaST and wait for the copying procedure to end. When the sources
have been fully copied, return to the overview of existing repositories and close the
configuration by selecting Finish.
Your installation server is now fully configured and ready for service. It is automatically started every time the system is started. No further intervention is required. You only need to configure and start this service correctly by hand if you
have deactivated the automatic configuration of the selected network service with
YaST as an initial step.
To deactivate a repository, select the repository to remove then select Delete. The installation data are removed from the system. To deactivate the network service, use
the respective YaST module.
If your installation server needs to provide the installation data for more than one
product of the product version, start the YaST installation server module and select
Add in the overview of existing repositories to configure the new repository.
14.2.2 Setting Up an NFS Repository
Manually
Setting up an NFS source for installation is basically done in two steps. In the first
step, create the directory structure holding the installation data and copy the installation media over to this structure. Second, export the directory holding the installation
data to the network.
To create a directory to hold the installation data, proceed as follows:
1 Log in as root.
2 Create a directory that will later hold all installation data and change into this directory. For example:
mkdir install/product/productversion
256
Deployment Guide
cd install/product/productversion
Replace product with an abbreviation of the product name and productversion with a string that contains the product name and version.
3 For each DVD contained in the media kit execute the following commands:
3a Copy the entire content of the installation DVD into the installation server
directory:
cp -a /media/path_to_your_DVD_drive .
Replace path_to_your_DVD_drive with the actual path under which
your DVD drive is addressed. Depending on the type of drive used in your
system, this can be cdrom, cdrecorder, dvd, or dvdrecorder.
3b Rename the directory to the DVD number:
mv path_to_your_DVD_drive DVDx
Replace x with the actual number of your DVD.
On SUSE Linux Enterprise Server, you can export the repository with NFS using
YaST. Proceed as follows:
1 Log in as root.
2 Start YaST > Network Services > NFS Server.
3 Select Start and Open Port in Firewall and click Next.
4 Select Add Directory and browse for the directory containing the installation
sources, in this case, productversion.
5 Select Add Host and enter the hostnames of the machines to which to export the installation data. Instead of specifying hostnames here, you could also use wild cards,
ranges of network addresses, or just the domain name of your network. Enter the
appropriate export options or leave the default, which works fine in most setups.
For more information about the syntax used in exporting NFS shares, read the exports man page.
6 Click Finish. The NFS server holding the SUSE Linux Enterprise Server repository
is automatically started and integrated into the boot process.
Remote Installation
257
If you prefer manually exporting the repository via NFS instead of using the YaST
NFS Server module, proceed as follows:
1 Log in as root.
2 Open the file /etc/exports and enter the following line:
/productversion *(ro,root_squash,sync)
This exports the directory /productversion to any host that is part of this network or to any host that can connect to this server. To limit the access to this server, use netmasks or domain names instead of the general wild card *. Refer to the
export man page for details. Save and exit this configuration file.
3 To add the NFS service to the list of servers started during system boot, execute
the following commands:
insserv /etc/init.d/nfsserver
4 Start the NFS server with rcnfsserver start. If you need to change the configuration of your NFS server later, modify the configuration file and restart the
NFS daemon with rcnfsserver restart.
Announcing the NFS server via OpenSLP makes its address known to all clients in
your network.
1 Log in as root.
2 Create the /etc/slp.reg.d/install.suse.nfs.reg configuration file
with the following lines:
# Register the NFS Installation Server
service:install.suse:nfs://$HOSTNAME/path_to_repository/DVD1,en,65535
description=NFS Repository
Replace path_to_repository with the actual path to the installation source
on your server.
3 Start the OpenSLP daemon with rcslpd start.
For more information about OpenSLP, refer to the package documentation located
under /usr/share/doc/packages/openslp/ or refer to Chapter 23, SLP
Services in the Network (↑Administration Guide). More Information about NFS, refer
to Chapter 29, Sharing File Systems with NFS (↑Administration Guide).
258
Deployment Guide
14.2.3 Setting Up an FTP Repository
Manually
Creating an FTP repository is very similar to creating an NFS repository. An FTP
repository can be announced over the network using OpenSLP as well.
1 Create a directory holding the installation sources as described in Section 14.2.2,
“Setting Up an NFS Repository Manually” (page 256).
2 Configure the FTP server to distribute the contents of your installation directory:
2a Log in as root and install the package vsftpd using the YaST software
management.
2b Enter the FTP server root directory:
cd /srv/ftp
2c Create a subdirectory holding the installation sources in the FTP root directory:
mkdir repository
Replace repository with the product name.
2d Mount the contents of the installation repository into the change root environment of the FTP server:
mount --bind path_to_repository /srv/ftp/repository
Replace path_to_repository and repository with values matching your setup. If you need to make this permanent, add it to /etc/
fstab.
2e Start vsftpd with vsftpd.
3 Announce the repository via OpenSLP, if this is supported by your network setup:
3a Create the /etc/slp.reg.d/install.suse.ftp.reg configuration file with the following lines:
# Register the FTP Installation Server
service:install.suse:ftp://$HOSTNAME/repository/DVD1,en,65535
description=FTP Repository
Remote Installation
259
Replace repository with the actual name to the repository directory on
your server. The service: line should be entered as one continuous line.
3b Start the OpenSLP daemon with rcslpd start.
TIP: Configuring an FTP Server with YaST
If you prefer using YaST over manually configuring the FTP installation server, refer to Chapter 32, Setting up an FTP Server with YaST (↑Administration Guide) for more information on how to use the YaST FTP server module.
14.2.4 Setting Up an HTTP Repository
Manually
Creating an HTTP repository is very similar to creating an NFS repository. An HTTP
repository can be announced over the network using OpenSLP as well.
1 Create a directory holding the installation sources as described in Section 14.2.2,
“Setting Up an NFS Repository Manually” (page 256).
2 Configure the HTTP server to distribute the contents of your installation directory:
2a Install the Web server Apache as described in
Section “Installation” (Chapter 31, The Apache HTTP Server, ↑Administration Guide).
2b Enter the root directory of the HTTP server (/srv/www/htdocs) and
create the subdirectory that will hold the installation sources:
mkdir repository
Replace repository with the product name.
2c Create a symbolic link from the location of the installation sources to the
root directory of the Web server (/srv/www/htdocs):
ln -s /path_to_repository /srv/www/htdocs/repository
2d Modify the configuration file of the HTTP server (/etc/apache2/de​
fault-server.conf) to make it follow symbolic links. Replace the
following line:
260
Deployment Guide
Options None
with
Options Indexes FollowSymLinks
2e Reload the HTTP server configuration using rcapache2 reload.
3 Announce the repository via OpenSLP, if this is supported by your network setup:
3a Create the /etc/slp.reg.d/install.suse.http.reg configuration file with the following lines:
# Register the HTTP Installation Server
service:install.suse:http://$HOSTNAME/repository/DVD1/,en,65535
description=HTTP Repository
Replace repository with the actual path to the repository on your server. The service: line should be entered as one continuous line.
3b Start the OpenSLP daemon using rcslpd restart.
14.2.5 Managing an SMB Repository
Using SMB, you can import the installation sources from a Microsoft Windows server
and start your Linux deployment even with no Linux machine around.
To set up an exported Windows Share holding your SUSE Linux Enterprise Server
repository, proceed as follows:
1 Log in to your Windows machine.
2 Create a new folder that will hold the entire installation tree and name it INS​
TALL, for example.
3 Export this share according the procedure outlined in your Windows documentation.
4 Enter this share and create a subfolder, called product. Replace product with
the actual product name.
5 Enter the INSTALL/product folder and copy each DVD to a separate folder,
such as DVD1 and DVD2.
Remote Installation
261
To use a SMB mounted share as a repository, proceed as follows:
1 Boot the installation target.
2 Select Installation.
3 Press F4 for a selection of the repository.
4 Choose SMB and enter the Windows machine's name or IP address, the share
name (INSTALL/product/DVD1, in this example), username, and password.
Your syntax looks like this:
smb://workdomain;user:[email protected]/INSTALL/DVD1
After you hit Enter, YaST starts and you can perform the installation.
14.2.6 Using ISO Images of the
Installation Media on the Server
Instead of copying physical media into your server directory manually, you can also
mount the ISO images of the installation media into your installation server and use
them as a repository. To set up an HTTP, NFS or FTP server that uses ISO images instead of media copies, proceed as follows:
1 Download the ISO images and save them to the machine to use as the installation
server.
2 Log in as root.
3 Choose and create an appropriate location for the installation data, as described
in Section 14.2.2, “Setting Up an NFS Repository Manually” (page 256), Section 14.2.3, “Setting Up an FTP Repository Manually” (page 259), or Section 14.2.4, “Setting Up an HTTP Repository Manually” (page 260).
4 Create subdirectories for each DVD.
5 To mount and unpack each ISO image to the final location, issue the following
command:
mount -o loop path_to_isopath_to_repository/product/mediumx
262
Deployment Guide
Replace path_to_iso with the path to your local copy of the ISO image,
path_to_repository with the source directory of your server, product
with the product name, and mediumx with the type (CD or DVD) and number of
media you are using.
6 Repeat the previous step to mount all ISO images needed for your product.
7 Start your installation server as usual, as described in Section 14.2.2, “Setting Up
an NFS Repository Manually” (page 256), Section 14.2.3, “Setting Up an FTP
Repository Manually” (page 259), or Section 14.2.4, “Setting Up an HTTP
Repository Manually” (page 260).
To automatically mount the ISO images at boot time, add the respective mount entries
to /etc/fstab. An entry according to the previous example would look like the
following:
path_to_iso path_to_repository/productmedium auto loop
14.3 Preparing the Boot of the
Target System
This section covers the configuration tasks needed in complex boot scenarios. It contains ready-to-apply configuration examples for DHCP, PXE boot, TFTP, and Wake
on LAN.
14.3.1 Setting Up a DHCP Server
There are two ways to set up a DHCP server. For SUSE Linux Enterprise Server,
YaST provides a graphical interface to the process. Users can also manually edit the
configuration files. For more information about DHCP servers, see also Chapter 26,
DHCP (↑Administration Guide).
14.3.1.1 Setting Up a DHCP Server with YaST
To announce the TFTP server's location to the network clients and specify the boot
image file the installation target should use, add two declarations to your DHCP server configuration.
Remote Installation
263
1 Log in as root to the machine hosting the DHCP server.
2 Start YaST > Network Services > DHCP Server.
3 Complete the setup wizard for basic DHCP server setup.
4 Select Expert Settings and select Yes when warned about leaving the start-up dialog.
5 In the Configured Declarations dialog, select the subnet in which the new system
should be located and click Edit.
6 In the Subnet Configuration dialog select Add to add a new option to the subnet's
configuration.
7 Select filename and enter pxelinux.0 as the value.
8 Add another option (next-server) and set its value to the address of the TFTP
server.
9 Select OK and Finish to complete the DHCP server configuration.
To configure DHCP to provide a static IP address to a specific host, enter the Expert Settings of the DHCP server configuration module (Step 4 (page 264)) and add
a new declaration of the host type. Add the options hardware and fixed-address to this host declaration and provide the appropriate values.
14.3.1.2 Setting Up a DHCP Server Manually
All the DHCP server needs to do, apart from providing automatic address allocation
to your network clients, is to announce the IP address of the TFTP server and the file
that needs to be pulled in by the installation routines on the target machine.
1 Log in as root to the machine hosting the DHCP server.
2 Append the following lines to a subnet configuration of your DHCP server's configuration file located under /etc/dhcpd.conf:
subnet 192.168.1.0 netmask 255.255.255.0 {
range dynamic-bootp 192.168.1.200 192.168.1.228;
# PXE related stuff
#
# "next-server" defines the TFTP server that will be used
next-server ip_tftp_server;
264
Deployment Guide
#
# "filename" specifies the pxelinux image on the TFTP server
# the server runs in chroot under /srv/tftpboot
filename "pxelinux.0";
}
Replace ip_of_the_tftp_server with the actual IP address of the TFTP
server. For more information about the options available in dhcpd.conf, refer
to the dhcpd.conf manual page.
3 Restart the DHCP server by executing rcdhcpd restart.
If you plan on using SSH for the remote control of a PXE and Wake on LAN installation, explicitly specify the IP address DHCP should provide to the installation target.
To achieve this, modify the above mentioned DHCP configuration according to the
following example:
group {
# PXE related stuff
#
# "next-server" defines the TFTP server that will be used
next-server ip_tftp_server:
#
# "filename" specifies the pxelinux image on the TFTP server
# the server runs in chroot under /srv/tftpboot
filename "pxelinux.0";
host test {
hardware ethernet mac_address;
fixed-address some_ip_address;
}
}
The host statement introduces the hostname of the installation target. To bind the
hostname and IP address to a specific host, you must know and specify the system's
hardware (MAC) address. Replace all the variables used in this example with the actual values that match your environment.
After restarting the DHCP server, it provides a static IP to the host specified, enabling
you to connect to the system via SSH.
14.3.2 Setting Up a TFTP Server
Set up a TFTP server with YaST on SUSE Linux Enterprise Server and SUSE Linux
Enterprise Server or set it up manually on any other Linux operating system that supports xinetd and TFTP. The TFTP server delivers the boot image to the target system
once it boots and sends a request for it.
Remote Installation
265
14.3.2.1 Setting Up a TFTP Server Using YaST
1 Log in as root.
2 Start YaST > Network Services > TFTP Server and install the requested package.
3 Click Enable to make sure that the server is started and included in the boot routines. No further action from your side is required to secure this. xinetd starts tftpd
at boot time.
4 Click Open Port in Firewall to open the appropriate port in the firewall running on
your machine. If there is no firewall running on your server, this option is not available.
5 Click Browse to browse for the boot image directory. The default directory /
tftpboot is created and selected automatically.
6 Click Finish to apply your settings and start the server.
14.3.2.2 Setting Up a TFTP Server Manually
1 Log in as root and install the packages tftp and xinetd.
2 If unavailable, create /srv/tftpboot and /srv/tftp​
boot/pxelinux.cfg directories.
3 Add the appropriate files needed for the boot image as described in Section 14.3.3,
“Using PXE Boot” (page 267).
4 Modify the configuration of xinetd located under /etc/xinetd.d to make sure
that the TFTP server is started on boot:
4a If it does not exist, create a file called tftp under this directory with
touch tftp. Then run chmod 755 tftp.
4b Open the file tftp and add the following lines:
service tftp
{
socket_type
protocol
wait
user
266
Deployment Guide
=
=
=
=
dgram
udp
yes
root
server
server_args
disable
= /usr/sbin/in.tftpd
= -s /srv/tftpboot
= no
}
4c Save the file and restart xinetd with rcxinetd restart.
14.3.3 Using PXE Boot
Some technical background information as well as PXE's complete specifications
are available in the Preboot Execution Environment (PXE) Specification (http://
www.pix.net/software/pxeboot/archive/pxespec.pdf).
1 Change to the directory boot/<architecture>/loader of your installation
repository and copy the linux, initrd, message, biostest, and memtest
files to the /srv/tftpboot directory by entering the following:
cp -a linux initrd message biostest memtest /srv/tftpboot
2 Install the syslinux package directly from your installation DVDs with YaST.
3 Copy the /usr/share/syslinux/pxelinux.0 file to the /srv/tftp​
boot directory by entering the following:
cp -a /usr/share/syslinux/pxelinux.0 /srv/tftpboot
4 Change to the directory of your installation repository and copy the
isolinux.cfg file to /srv/tftpboot/pxelinux.cfg/default by
entering the following:
cp -a boot/<architecture>/loader/isolinux.cfg /srv/tftpboot/pxelinux.cfg/
default
5 Edit the /srv/tftpboot/pxelinux.cfg/default file and remove the
lines beginning with readinfo and framebuffer.
6 Insert the following entries in the append lines of the default failsafe and
apic labels:
insmod=kernel module
By means of this entry, enter the network Kernel module needed to support
network installation on the PXE client. Replace kernel module with the
appropriate module name for your network device.
Remote Installation
267
netdevice=interface
This entry defines the client's network interface that must be used for the network installation. It is only necessary if the client is equipped with several network cards and must be adapted accordingly. In case of a single network card,
this entry can be omitted.
install=nfs://ip_instserver/path_to_repository/DVD1
This entry defines the NFS server and the repository for the client installation. Replace ip_instserver with the actual IP address of your installation server. path_to_repository should be replaced with the actual path
to the repository. HTTP, FTP, or SMB repositories are addressed in a similar manner, except for the protocol prefix, which should read http, ftp, or
smb.
IMPORTANT
If you need to pass other boot options to the installation routines, such
as SSH or VNC boot parameters, append them to the install entry. An overview of parameters and some examples are given in Section 14.4, “Booting the Target System for Installation” (page 274).
TIP: Changing Kernel and initrd Filenames
It is possible to use different filenames for Kernel and initrd images. This
is useful if you want to provide different operating systems from the same
boot server. However, you should be aware that only one dot is permitted
in the filenames that are provided by TFTP for the PXE boot.
An example /srv/tftpboot/pxelinux.cfg/default file follows. Adjust the protocol prefix for the repository to match your network setup and specify
your preferred method of connecting to the installer by adding the vnc and vncpassword or the usessh and sshpassword options to the install entry. The lines separated by \ must be entered as one continuous line without a line
break and without the \.
default hard disk
# default
label linux
kernel linux
append initrd=initrd ramdisk_size=65536 \
268
Deployment Guide
install=nfs://ip_instserver/path_to_repository/product/DVD1
# repair
label repair
kernel linux
append initrd=initrd splash=silent repair=1 showopts
# rescue
label rescue
kernel linux
append initrd=initrd ramdisk_size=65536 rescue=1
# bios test
label firmware
kernel linux
append initrd=biostest,initrd splash=silent install=exec:/bin/
run_biostest showopts
# memory test
label memtest
kernel memtest
# hard disk
label hard disk
localboot 0
implicit
display
prompt
timeout
0
message
1
100
7 Replace ip_instserver and path_to_repository with the values used
in your setup.
The following section serves as a short reference to the PXELINUX options used
in this setup. Find more information about the options available in the documentation of the syslinux package located under /usr/share/doc/pack​
ages/syslinux/.
14.3.4 PXELINUX Configuration Options
The options listed here are a subset of all the options available for the PXELINUX
configuration file.
APPEND options...
Add one or more options to the Kernel command line. These are added for both
automatic and manual boots. The options are added at the very beginning of the
Remote Installation
269
Kernel command line, usually permitting explicitly entered Kernel options to
override them.
APPEND Append nothing. APPEND with a single hyphen as argument in a LABEL section
can be used to override a global APPEND.
DEFAULT kernel options...
Sets the default Kernel command line. If PXELINUX boots automatically, it acts
as if the entries after DEFAULT had been typed in at the boot prompt, except the
auto option is automatically added, indicating an automatic boot.
If no configuration file is present or no DEFAULT entry is present in the configuration file, the default is the Kernel name “linux” with no options.
IFAPPEND FLAG
Adds a specific option to the kernel command line depending on the FLAG value.
The IFAPPEND option is available only on PXELINUX. FLAG expects a value,
described in Table 14.1, “Generated and Added Kernel Command Line Options
from IFAPPEND” (page 270):
Table 14.1: Generated and Added Kernel Command Line Options from
IFAPPEND
Argument
Generated Kernel Command Line / Description
1
ip=CLIENT_IP:BOOT_SERVER_IP:GW_IP:NETMASK
The placeholders are replaced based on the input from the
DHCP/BOOTP or PXE boot server.
Note, this option is not a substitute for running a DHCP
client in the booted system. Without regular renewals, the
lease acquired by the PXE BIOS will expire, making the IP
address available for reuse by the DHCP server.
2
BOOTIF=MAC_ADDRESS_OF_BOOT_INTERFACE
This option is useful if you want to avoid timeouts when the
installation server probes one LAN interface after the other
until it gets a reply from a DHCP server. Using this option
allows an initrd program to determine from which interface
270
Deployment Guide
Argument
Generated Kernel Command Line / Description
the system has been booted. linuxrc reads this option and uses this network interface.
4
SYSUUID=SYSTEM_UUID
Adds UUIDs in lowercase hexadecimals, see /usr/
share/doc/packages/syslinux/pxelinux.txt
LABEL label KERNEL image APPEND options...
Indicates that if label is entered as the Kernel to boot, PXELINUX should instead boot image and the specified APPEND options should be used instead of
the ones specified in the global section of the file (before the first LABEL command). The default for image is the same as label and, if no APPEND is given, the default is to use the global entry (if any). Up to 128 LABEL entries are
permitted.
Note that GRUB uses the following syntax:
title mytitle
kernel my_kernelmy_kernel_options
initrd myinitrd
PXELINUX uses the following syntax:
label mylabel
kernel mykernel
append myoptions
Labels are mangled as if they were filenames and they must be unique after mangling. For example, the two labels “v2.6.30” and “v2.6.31” would not be distinguishable under PXELINUX because both mangle to the same DOS filename.
The Kernel does not have to be a Linux Kernel; it can be a boot sector or a COMBOOT file.
LOCALBOOT type
On PXELINUX, specifying LOCALBOOT 0 instead of a KERNEL option means
invoking this particular label and causes a local disk boot instead of a Kernel
boot.
Argument
Description
0
Perform a normal boot
Remote Installation
271
Argument
Description
4
Perform a local boot with the Universal Network Driver Interface
(UNDI) driver still resident in
memory
5
Perform a local boot with the entire
PXE stack, including the UNDI driver, still resident in memory
All other values are undefined. If you do not know what the UNDI or PXE stacks
are, specify 0.
TIMEOUT time-out
Indicates how long to wait at the boot prompt until booting automatically, in units
of 1/10 second. The time-out is canceled as soon as the user types anything on the
keyboard, assuming the user will complete the command begun. A time-out of zero disables the time-out completely (this is also the default). The maximum possible time-out value is 35996 (just less than one hour).
PROMPT flag_val
If flag_val is 0, displays the boot prompt only if Shift or Alt is pressed or
Caps Lock or Scroll Lock is set (this is the default). If flag_val is 1, always
displays the boot prompt.
F2 filename
F1 filename
..etc...
F9 filename
F10 filename
Displays the indicated file on the screen when a function key is pressed at the
boot prompt. This can be used to implement preboot online help (presumably for
the Kernel command line options). For backward compatibility with earlier releases, F10 can be also entered as F0. Note that there is currently no way to bind
filenames to F11 and F12.
272
Deployment Guide
14.3.5 Preparing the Target System for
PXE Boot
Prepare the system's BIOS for PXE boot by including the PXE option in the BIOS
boot order.
WARNING: BIOS Boot Order
Do not place the PXE option ahead of the hard disk boot option in the BIOS.
Otherwise this system would try to re-install itself every time you boot it.
14.3.6 Preparing the Target System for
Wake on LAN
Wake on LAN (WOL) requires the appropriate BIOS option to be enabled prior to
the installation. Also, note down the MAC address of the target system. This data is
needed to initiate Wake on LAN.
14.3.7 Wake on LAN
Wake on LAN allows a machine to be turned on by a special network packet containing the machine's MAC address. Because every machine in the world has a unique
MAC identifier, you do not need to worry about accidentally turning on the wrong
machine.
IMPORTANT: Wake on LAN across Different Network Segments
If the controlling machine is not located in the same network segment as the
installation target that should be awakened, either configure the WOL requests to be sent as multicasts or remotely control a machine on that network
segment to act as the sender of these requests.
Users of SUSE Linux Enterprise Server can use a YaST module called WOL to easily configure Wake on LAN. Users of other versions of SUSE Linux-based operating
systems can use a command line tool.
Remote Installation
273
14.3.8 Wake on LAN with YaST
1 Log in as root.
2 Start YaST > Network Services > WOL.
3 Click Add and enter the hostname and MAC address of the target system.
4 To turn on this machine, select the appropriate entry and click Wake up.
14.4 Booting the Target System for
Installation
Basically, there are two different ways to customize the boot process for installation
apart from those mentioned under Section 14.3.7, “Wake on LAN” (page 273)
and Section 14.3.3, “Using PXE Boot” (page 267). You can either use the default
boot options and function keys or use the boot options prompt of the installation boot
screen to pass any boot options that the installation Kernel might need on this particular hardware.
14.4.1 Using the Default Boot Options
The boot options are described in detail in Chapter 6, Installation with
YaST (page 93). Generally, just selecting Installation starts the installation boot
process.
If problems occur, use Installation—ACPI Disabled or Installation—Safe Settings. For more information about troubleshooting the installation process, refer to
Section “Installation Problems” (Chapter 36, Common Problems and Their Solutions,
↑Administration Guide).
The menu bar at the bottom screen offers some advanced functionality needed in
some setups. Using the F keys, you can specify additional options to pass to the installation routines without having to know the detailed syntax of these parameters (see
Section 14.4.2, “Using Custom Boot Options” (page 275)). A detailed description
of the available function keys is available at Section 6.6, “The Boot Screen on Machines Equipped with Traditional BIOS” (page 98).
274
Deployment Guide
14.4.2 Using Custom Boot Options
Using the appropriate set of boot options helps facilitate your installation procedure.
Many parameters can also be configured later using the linuxrc routines, but using the
boot options is easier. In some automated setups, the boot options can be provided
with initrd or an info file.
The following table lists all installation scenarios mentioned in this chapter with the
required parameters for booting and the corresponding boot options. Just append all
of them in the order they appear in this table to get one boot option string that is handed to the installation routines. For example (all in one line):
install=xxx netdevice=xxx hostip=xxx netmask=xxx vnc=xxx vncpassword=xxx
Replace all the values xxx in this string with the values appropriate for your setup.
Table 14.2: Installation (Boot) Scenarios Used in This Chapter
Installation Scenario
Parameters Needed
for Booting
Boot Options
Chapter 6, Installation
with YaST (page 93)
None: system boots automatically
None needed
Section 14.1.1, “Simple
• Location of the inRemote Installation via
stallation server
VNC—Static Network
• Network device
Configuration” (page 246) • IP address
• Netmask
• Gateway
• VNC enablement
• VNC password
• install=(nfs,http,
ftp,smb)://
path_to_instmedia
• netdevice=some_netdevice
(only needed if several network devices
are available)
• hostip=some_ip
• netmask=some_netmask
• gateway=ip_gateway
• vnc=1
• vncpassword=some_password
Section 14.1.2, “Simple Remote Installation via VNC—
• install=(nfs,http,
ftp,smb)://
path_to_instmedia
• vnc=1
• Location of the installation server
• VNC enablement
• VNC password
Remote Installation
275
Installation Scenario
Parameters Needed
for Booting
Dynamic Network
Configuration” (page 247)
Section 14.1.3, “Remote Installation
via VNC—PXE
Boot and Wake on
LAN” (page 249)
276
Boot Options
• vncpassword=some_password
• Location of the installation server
• Location of the
TFTP server
• VNC enablement
• VNC password
Not applicable; process
managed through PXE
and DHCP
Section 14.1.4, “Simple
• Location of the inRemote Installation via
stallation server
SSH—Static Network
• Network device
Configuration” (page 250) • IP address
• Netmask
• Gateway
• SSH enablement
• SSH password
• install=(nfs,http,
ftp,smb)://
path_to_instmedia
• netdevice=some_netdevice
(only needed if several network devices
are available)
• hostip=some_ip
• netmask=some_netmask
• gateway=ip_gateway
• usessh=1
• sshpassword=some_password
Section 14.1.5, “Sim• Location of the inple Remote Instalstallation server
lation via SSH—
• SSH enablement
Dynamic Network
• SSH password
Configuration” (page 251)
• install=(nfs,http,
ftp,smb)://
path_to_instmedia
• usessh=1
• sshpassword=some_password
Section 14.1.6, “Remote Installation
via SSH—PXE
Boot and Wake on
LAN” (page 253)
Not applicable; process
managed through PXE
and DHCP
Deployment Guide
• Location of the installation server
• Location of the
TFTP server
• SSH enablement
• SSH password
TIP: More Information about linuxrc Boot Options
Find more information about the linuxrc boot options used for booting a Linux
system at http://en.opensuse.org/SDB:Linuxrc.
14.4.2.1 Installing Add-On Products and Driver
Updates
SUSE Linux Enterprise Server supports the installation of Add-On products providing extensions (for example the SUSE Linux Enterprise High Availability Extension),
third-party products and drivers or additional software. In order to automatically install an Add-On product when deploying SUSE Linux Enterprise Server remotely,
specify the addon=REPOSITORY parameter.
REPOSITORY needs to be a hosted repository that can be read by YaST (YaST2 or
YUM (rpm-md)). ISO images are currently not supported.
TIP: Driver Updates
Driver Updates can be found at http://drivers.suse.com/. Not all driver updates are provided as repositories—some are only available as iso images and therefore cannot be installed with the addon parameter. Instructions on how to install driver updates via iso image are available at http://
drivers.suse.com/doc/kit_usage.html.
14.5 Monitoring the Installation
Process
There are several options for remotely monitoring the installation process. If the proper boot options have been specified while booting for installation, either VNC or SSH
can be used to control the installation and system configuration from a remote workstation.
Remote Installation
277
14.5.1 VNC Installation
Using any VNC viewer software, you can remotely control the installation of SUSE
Linux Enterprise Server from virtually any operating system. This section introduces
the setup using a VNC viewer application or a Web browser.
14.5.1.1 Preparing for VNC Installation
All you need to do on the installation target to prepare for a VNC installation is
to provide the appropriate boot options at the initial boot for installation (see Section 14.4.2, “Using Custom Boot Options” (page 275)). The target system boots into a text-based environment and waits for a VNC client to connect to the installation
program.
The installation program announces the IP address and display number needed to connect for installation. If you have physical access to the target system, this information
is provided right after the system booted for installation. Enter this data when your
VNC client software prompts for it and provide your VNC password.
Because the installation target announces itself via OpenSLP, you can retrieve the address information of the installation target via an SLP browser without the need for
any physical contact to the installation itself, provided your network setup and all machines support OpenSLP:
1 Start the KDE file and Web browser Konqueror.
2 Enter service://yast.installation.suse in the location bar. The
target system then appears as an icon in the Konqueror screen. Clicking this icon
launches the KDE VNC viewer in which to perform the installation. Alternatively,
run your VNC viewer software with the IP address provided and add :1 at the end
of the IP address for the display the installation is running on.
14.5.1.2 Connecting to the Installation Program
Basically, there are two ways to connect to a VNC server (the installation target in this
case). You can either start an independent VNC viewer application on any operating
system or connect using a Java-enabled Web browser.
Using VNC, you can control the installation of a Linux system from any other operating system, including other Linux flavors, Windows, or Mac OS.
278
Deployment Guide
On a Linux machine, make sure that the package tightvnc is installed. On a Windows machine, install the Windows port of this application, which can be obtained at
the TightVNC home page (http://www.tightvnc.com/download.html).
To connect to the installation program running on the target machine, proceed as follows:
1 Start the VNC viewer.
2 Enter the IP address and display number of the installation target as provided by
the SLP browser or the installation program itself:
ip_address:display_number
A window opens on your desktop displaying the YaST screens as in a normal local
installation.
Using a Web browser to connect to the installation program makes you totally independent of any VNC software or the underlying operating system. As long as the
browser application has Java support enabled, you can use any browser (Firefox, Internet Explorer, Konqueror, Opera, etc.) to perform the installation of your Linux system.
To perform a VNC installation, proceed as follows:
1 Launch your preferred Web browser.
2 Enter the following at the address prompt:
http://ip_address_of_target:5801
3 Enter your VNC password when prompted to do so. The browser window now displays the YaST screens as in a normal local installation.
14.5.2 SSH Installation
Using SSH, you can remotely control the installation of your Linux machine using any
SSH client software.
14.5.2.1 Preparing for SSH Installation
Apart from installing the appropriate software package (OpenSSH for Linux and
PuTTY for Windows), you just need to pass the appropriate boot options to enable
Remote Installation
279
SSH for installation. See Section 14.4.2, “Using Custom Boot Options” (page 275)
for details. OpenSSH is installed by default on any SUSE Linux–based operating system.
14.5.2.2 Connecting to the Installation Program
1 Retrieve the installation target's IP address. If you have physical access to the target
machine, just take the IP address the installation routine provides at the console after the initial boot. Otherwise take the IP address that has been assigned to this particular host in the DHCP server configuration.
2 At a command line, enter the following command:
ssh -X [email protected]
ip_address_of_target
Replace ip_address_of_target with the actual IP address of the installation
target.
3 When prompted for a username, enter root.
4 When prompted for the password, enter the password that has been set with the
SSH boot option. After you have successfully authenticated, a command line
prompt for the installation target appears.
5 Enter yast to launch the installation program. A window opens showing the normal YaST screens as described in Chapter 6, Installation with YaST (page 93).
280
Deployment Guide
Advanced Disk Setup
Sophisticated system configurations require specific disk setups. All common partitioning tasks can be done with YaST. To get persistent device naming with block
devices, use the block devices below /dev/disk/by-id or /dev/disk/byuuid. Logical Volume Management (LVM) is a disk partitioning scheme that is designed to be much more flexible than the physical partitioning used in standard setups.
Its snapshot functionality enables easy creation of data backups. Redundant Array of
Independent Disks (RAID) offers increased data integrity, performance, and fault tolerance. SUSE Linux Enterprise Server also supports multipath I/O (see Chapter 7,
Managing Multipath I/O for Devices (↑Storage Administration Guide) for details), and
there is also the option to use iSCSI as a networked disk (read more about iSCSI in
Chapter 14, Mass Storage over IP Networks: iSCSI (↑Storage Administration Guide)).
15
15.1 Using the YaST Partitioner
With the expert partitioner, shown in Figure 15.1, “The YaST
Partitioner” (page 282), manually modify the partitioning of one or several hard
disks. You can add, delete, resize, and edit partitions, as well as access the soft RAID,
and LVM configuration.
WARNING: Repartitioning the Running System
Although it is possible to repartition your system while it is running, the risk of
making a mistake that causes the data loss is very high. Try to avoid repartitioning your installed system and always do a complete backup of your data
before attempting to do so.
Advanced Disk Setup
281
Figure 15.1: The YaST Partitioner
TIP: IBM System z: Device Names
IBM System z recognize only DASD and SCSI hard disks. IDE hard disks
are not supported. This is why these devices appear in the partition table as
dasda or sda for the first recognized device.
All existing or suggested partitions on all connected hard disks are displayed in the list
of Available Storage in the YaST Expert Partitioner dialog. Entire hard disks are listed
as devices without numbers, such as /dev/sda (or /dev/dasda). Partitions are
listed as parts of these devices, such as /dev/sda1 (or /dev/dasda1, respectively). The size, type, encryption status, file system, and mount point of the hard disks
and their partitions are also displayed. The mount point describes where the partition
appears in the Linux file system tree.
Several functional views are available on the lefthand System View. Use these views
to gather information about existing storage configurations, or to configure functions
like RAID, Volume Management, Crypt Files, or view file systems with additional features, such as BTRFS, NFS, or TMPFS.
If you run the expert dialog during installation, any free hard disk space is also listed and automatically selected. To provide more disk space to SUSE® Linux Enterprise Server, free the needed space starting from the bottom toward the top of the list
(starting from the last partition of a hard disk toward the first).
15.1.1 Partition Types
282
Deployment Guide
TIP: IBM System z: Hard Disks
On the IBM System z platforms, SUSE Linux Enterprise Server supports
SCSI hard disks as well as DASDs (direct access storage devices). While
SCSI disks can be partitioned as described below, DASDs can have no more
than three partition entries in their partition tables.
Every hard disk has a partition table with space for four entries. Every entry in the
partition table corresponds to a primary partition or an extended partition. Only one
extended partition entry is allowed, however.
A primary partition simply consists of a continuous range of cylinders (physical disk
areas) assigned to a particular operating system. With primary partitions you would
be limited to four partitions per hard disk, because more do not fit in the partition table. This is why extended partitions are used. Extended partitions are also continuous
ranges of disk cylinders, but an extended partition may be divided into logical partitions itself. Logical partitions do not require entries in the partition table. In other
words, an extended partition is a container for logical partitions.
If you need more than four partitions, create an extended partition as the fourth partition (or earlier). This extended partition should occupy the entire remaining free
cylinder range. Then create multiple logical partitions within the extended partition.
The maximum number of logical partitions is 63, independent of the disk type. It does
not matter which types of partitions are used for Linux. Primary and logical partitions
both function normally.
TIP: GPT Partition Table
If you need to create more than 4 primary partitions on one hard disk, you
have to use the GPT partition type. This type removes the primary partitions
number restriction, and supports partitions bigger than 2 TB as well.
To use GPT, run the YaST Partitioner, click the relevant disk name in the
System View and choose Expert > Create New Partition Table > GPT.
15.1.2 Creating a Partition
To create a partition from scratch select Hard Disks and then a hard disk with free
space. The actual modification can be done in the Partitions tab:
Advanced Disk Setup
283
1 Select Add and specify the partition type (primary or extended). Create up to four
primary partitions or up to three primary partitions and one extended partition.
Within the extended partition, create several logical partitions (see Section 15.1.1,
“Partition Types” (page 282)).
2 Specify the size of the new partition. You can either choose to occupy all the free
unpartitioned space, or enter a custom size.
3 Select the file system to use and a mount point. YaST suggests a mount point for
each partition created. To use a different mount method, like mount by label, select
Fstab Options. For more information on supported file systems, see root.
4 Specify additional file system options if your setup requires them. This is necessary, for example, if you need persistent device names. For details on the available
options, refer to Section 15.1.3, “Editing a Partition” (page 287).
5 Click Finish to apply your partitioning setup and leave the partitioning module.
If you created the partition during installation, you are returned to the installation
overview screen.
15.1.2.1 Btrfs Partitioning
If you want to use Btrfs (see Chapter 4, Snapshots/Rollback with Snapper (↑Administration Guide) and Chapter 1, Overview of File Systems in Linux (↑Storage Administration Guide) for more information on Btrfs) as your default file system for a newly installed system, click Partitioning on the Installation Settings screen, and check Use
Btrfs as Default Filesystem. The installation system then suggests creating the /boot
partition formatted with Ext3 file system, and the root / partition formatted with
Btrfs holding a default set of subvolumes, which you can modify with the Expert Partitioner tool later.
The root file system is the default subvolume and it is not listed in the list of created
subvolumes. As a default Btrfs subvolume, it can be mounted as a normal file system.
It is possible to create snapshots of Btrfs subvolumes - either manually, or automatically based on system events. For example when making changes to the file system,
zypper invokes the snapper command to create snapshots before and after the
change. This is useful if you are not satisfied with the change zypper made and
want to restore the previous state. As snapper invoked by zypper snapshots the
284
Deployment Guide
root file system by default, it is reasonable to exclude specific directories from being
snapshot, depending on the nature of data they hold. And that is why YaST suggests
creating the following separate subvolumes.
Suggested Btrfs Subvolumes
/tmp /var/tmp /var/run
Directories with frequently changed content.
/var/spool
Contains user data, such as mails.
/var/log
Contains system and applications' log files which should never be rolled back.
/var/crash
Contains memory dumps of crashed kernels.
/srv
Contains data files belonging to FTP and HTTP servers.
/opt
Contains third party software.
TIP: Size of Btrfs Partition
Because saved snapshots require more disk space, it is recommended to reserve more space for Btrfs partition than for a partition not capable of snapshotting (such as Ext3). Recommended size for a root Btrfs partition with
suggested subvolumes is 20GB.
Managing Btrfs Subvolumes using YaST
Subvolumes of a Btrfs partition can be now managed with the YaST Expert partitioner
module. You can add new or remove existing subvolumes.
Procedure 15.1: Btrfs Subvolumes with YaST
1 Start the YaST Expert Partitioner with System > Partitioner.
Advanced Disk Setup
285
2 Choose BTRFS in the left System View pane.
3 Select the Btrfs partition whose subvolumes you need to manage and click Edit.
4 Click Subvolume Handling. You can see a list off all existing subvolumes of the
selected Btrfs partition. You can notice a number of @/.snapshots/xyz/
snapshot entries — each of these subvolumes belongs to one existing snapshot.
5 Depending on whether you want to add or remove subvolumes, do the following:
5a To remove a subvolume, select it from the list of Exisitng Subvolumes and
click Remove.
5b To add a new subvolume, enter its name to the New Subvolume text field
and click Add new.
Figure 15.2: Btrfs Subvolumes in YaST Partitioner
6 Confirm with OK and Finish.
7 Leave the partitioner with Finish.
286
Deployment Guide
15.1.3 Editing a Partition
When you create a new partition or modify an existing partition, you can set various
parameters. For new partitions, the default parameters set by YaST are usually sufficient and do not require any modification. To edit your partition setup manually, proceed as follows:
1 Select the partition.
2 Click Edit to edit the partition and set the parameters:
File System ID
Even if you do not want to format the partition at this stage, assign it a file
system ID to ensure that the partition is registered correctly. Typical values are
Linux, Linux swap, Linux LVM, and Linux RAID.
File System
To change the partition file system, click Format Partition and select file system type in the File System list.
SUSE Linux Enterprise Server supports several types of file systems. Btrfs is
the Linux file system of choice because of its advanced features. It supports
copy-on-write functionality, creating snapshots, multi-device spanning, subvolumes, and other useful techniques. ReiserFS, JFS, XFS, and Ext3 are journaling file systems. These file systems are able to restore the system very quickly after a system crash, utilizing write processes logged during the operation.
Ext2 is not a journaling file system, but it is adequate for smaller partitions because it does not require much disk space for management.
NOTE: Support for Ext4 Filesystem
Because Btrfs proved to be more efficient and scalable than Ext4,
SUSE Linux Enterprise Server SP2 supports only read-only access to
Ext4 partitions. It is, however, still possible to access Ext4 partitions in
a read-write mode — you need to install the ext4-writeable package. Please note that this operation is not supported and taints the
Kernel.
Swap is a special format that allows the partition to be used as a virtual memory. Create a swap partition of at least 256 MB. However, if you use up your
Advanced Disk Setup
287
swap space, consider adding more memory to your system instead of adding
more swap space.
WARNING: Changing the file system
Changing the file system and reformatting partitions irreversibly
deletes all data from the partition.
For details on the various file systems, refer to Storage Administration Guide.
Encrypt Device
If you activate the encryption, all data is written to the hard disk in encrypted form. This increases the security of sensitive data, but reduces the system
speed, as the encryption takes some time to process. More information about
the encryption of file systems is provided in Chapter 11, Encrypting Partitions
and Files (↑Security Guide).
Mount Point
Specify the directory where the partition should be mounted in the file system
tree. Select from YaST suggestions or enter any other name.
Fstab Options
Specify various parameters contained in the global file system administration
file (/etc/fstab). The default settings should suffice for most setups. You
can, for example, change the file system identification from the device name
to a volume label. In the volume label, use all characters except / and space.
To get persistent devices names, use the mount option Device ID, UUID or LABEL. In SUSE Linux Enterprise Server, persistent device names are enabled by
default.
NOTE: IBM System z: Mounting by path
Since mounting by ID causes problems on IBM System z when using disk-to-disk copying for cloning purposes, devices are mounted by
path in /etc/fstab on IBM System z by default.
If you prefer to mount the partition by its label, you need to define one in the
Volume label text entry. For example, you could use the partition label HOME
for a partition intended to mount to /home.
288
Deployment Guide
If you intend to use quotas on the file system, use the mount option Enable
Quota Support. This must be done before you can define quotas for users in the
YaST User Management module. For further information on how to configure
user quota, refer to Section 12.3.5, “Managing Quotas” (page 229).
3 Select Finish to save the changes.
NOTE: Resize Filesystems
To resize an existing file system, select the partition and use Resize. Note,
that it is not possible to resize partitions while mounted. To resize partitions,
unmount the relevant partition before running the partitioner.
15.1.4 Expert Options
After you select a hard disk device (like sda) in the System View pane, you can access
the Expert... menu in the lower right part of the Expert Partitioner window. The menu
contains the following commands:
Create New Partition Table
This option helps you create a new partition table on the selected device.
WARNING: Creating a New Partition Table
Creating a new partition table on a device irreversibly removes all the
partitions and their data from that device.
Clone This Disk
This option helps you clone the device partition layout (but not the data) to other
available disk devices.
15.1.5 Advanced Options
After you select the hostname of the computer (the top-level of the tree in the System
View pane), you can access the Configure... menu in the lower right part of the Expert
Partitioner window. The menu contains the following commands:
Advanced Disk Setup
289
Configure iSCSI
To access SCSI over IP block devices, you first have to configure iSCSI. This results in additionally available devices in the main partition list.
Configure Multipath
Selecting this option helps you configure the multipath enhancement to the supported mass storage devices.
15.1.6 More Partitioning Tips
The following section includes a few hints and tips on partitioning that should help
you make the right decisions when setting up your system.
TIP: Cylinder Numbers
Note, that different partitioning tools may start counting the cylinders of a partition with 0 or with 1. When calculating the number of cylinders, you should
always use the difference between the last and the first cylinder number and
add one.
15.1.6.1 Using swap
Swap is used to extend the available physical memory. It is then possible to use more
memory than physical RAM available. The memory management system of kernels
before 2.4.10 needed swap as a safety measure. Then, if you did not have twice the
size of your RAM in swap, the performance of the system suffered. These limitations
no longer exist.
Linux uses a page called “Least Recently Used” (LRU) to select pages that might be
moved from memory to disk. Therefore, running applications have more memory
available and caching works more smoothly.
If an application tries to allocate the maximum allowed memory, problems with swap
can arise. There are three major scenarios to look at:
System with no swap
The application gets the maximum allowed memory. All caches are freed, and
thus all other running applications are slowed. After a few minutes, the kernel's
out-of-memory kill mechanism activates and kills the process.
290
Deployment Guide
System with medіum sized swap (128 MB–512 MB)
At first, the system slows like a system without swap. After all physical RAM has
been allocated, swap space is used as well. At this point, the system becomes very
slow and it becomes impossible to run commands from remote. Depending on the
speed of the hard disks that run the swap space, the system stays in this condition
for about 10 to 15 minutes until the out-of-memory kill mechanism resolves the
issue. Note that you will need a certain amount of swap if the computer needs to
perform a “suspend to disk”. In that case, the swap size should be large enough to
contain the necessary data from memory (512 MB–1GB).
System with lots of swap (several GB)
It is better to not have an application that is out of control and swapping excessively in this case. If you use such application, the system will need many hours
to recover. In the process, it is likely that other processes get timeouts and faults,
leaving the system in an undefined state, even after killing the faulty process. In
this case, do a hard machine reboot and try to get it running again. Lots of swap is
only useful if you have an application that relies on this feature. Such applications
(like databases or graphics manipulation programs) often have an option to directly use hard disk space for their needs. It is advisable to use this option instead of
using lots of swap space.
If your system is not out of control, but needs more swap after some time, it is possible to extend the swap space online. If you prepared a partition for swap space, just
add this partition with YaST. If you do not have a partition available, you may also
just use a swap file to extend the swap. Swap files are generally slower than partitions,
but compared to physical ram, both are extremely slow so the actual difference is negligible.
Procedure 15.2: Adding a Swap File Manually
To add a swap file in the running system, proceed as follows:
1 Create an empty file in your system. For example, if you want to add a swap file
with 128 MB swap at /var/lib/swap/swapfile, use the commands:
mkdir -p /var/lib/swap
dd if=/dev/zero of=/var/lib/swap/swapfile bs=1M count=128
2 Initialize this swap file with the command
mkswap /var/lib/swap/swapfile
3 Activate the swap with the command
Advanced Disk Setup
291
swapon /var/lib/swap/swapfile
To disable this swap file, use the command
swapoff /var/lib/swap/swapfile
4 Check the current available swap spaces with the command
cat /proc/swaps
Note that at this point, it is only temporary swap space. After the next reboot, it is
no longer used.
5 To enable this swap file permanently, add the following line to /etc/fstab:
/var/lib/swap/swapfile swap swap defaults 0 0
15.1.7 Partitioning and LVM
From the Expert partitioner, access the LVM configuration by clicking the Volume
Management item in the System View pane. However, if a working LVM configuration already exists on your system, it is automatically activated upon entering the initial LVM configuration of a session. In this case, all disks containing a partition (belonging to an activated volume group) cannot be repartitioned. The Linux kernel cannot reread the modified partition table of a hard disk when any partition on this disk
is in use. If you already have a working LVM configuration on your system, physical
repartitioning should not be necessary. Instead, change the configuration of the logical
volumes.
At the beginning of the physical volumes (PVs), information about the volume is written to the partition. To reuse such a partition for other non-LVM purposes, it is advisable to delete the beginning of this volume. For example, in the VG system and PV
/dev/sda2, do this with the command dd if=/dev/zero of=/dev/sda2
bs=512 count=1.
WARNING: File System for Booting
The file system used for booting (the root file system or /boot) must not be
stored on an LVM logical volume. Instead, store it on a normal physical partition.
For more details about LVM, see Storage Administration Guide (↑Storage Administration Guide).
292
Deployment Guide
15.2 LVM Configuration
This section briefly describes the principles behind the Logical Volume Manager
(LVM) and its multipurpose features. In Section 15.2.2, “LVM Configuration with
YaST” (page 295), learn how to set up LVM with YaST.
WARNING
Using LVM is sometimes associated with increased risk such as data loss.
Risks also include application crashes, power failures, and faulty commands.
Save your data before implementing LVM or reconfiguring volumes. Never
work without a backup.
15.2.1 The Logical Volume Manager
The LVM enables flexible distribution of hard disk space over several file systems.
It was developed because sometimes the need to change the segmenting of hard disk
space arises just after the initial partitioning has been done. Because it is difficult to
modify partitions on a running system, LVM provides a virtual pool (volume group,
VG for short) of memory space from which logical volumes (LVs) can be created as
needed. The operating system accesses these LVs instead of the physical partitions.
Volume groups can occupy more than one disk, so that several disks or parts of them
may constitute one single VG. This way, LVM provides a kind of abstraction from the
physical disk space that allows its segmentation to be changed in a much easier and
safer way than with physical repartitioning. Background information regarding physical partitioning can be found in Section 15.1.1, “Partition Types” (page 282) and
Section 15.1, “Using the YaST Partitioner” (page 281).
Advanced Disk Setup
293
Figure 15.3: Physical Partitioning versus LVM
DISK
PART
PART
DISK 1
PART
PART
PART
DISK 2
PART
PART
VG 1
LV 1
MP
MP
MP
MP
PART
VG 2
LV 2
LV 3
LV 4
MP
MP
MP
Figure 15.3, “Physical Partitioning versus LVM” (page 294) compares physical
partitioning (left) with LVM segmentation (right). On the left side, one single disk has
been divided into three physical partitions (PART), each with a mount point (MP) assigned so that the operating system can gain access. On the right side, two disks have
been divided into two and three physical partitions each. Two LVM volume groups
(VG 1 and VG 2) have been defined. VG 1 contains two partitions from DISK 1 and
one from DISK 2. VG 2 contains the remaining two partitions from DISK 2. In LVM,
the physical disk partitions that are incorporated in a volume group are called physical
volumes (PVs). Within the volume groups, four LVs (LV 1 through LV 4) have been
defined. They can be used by the operating system via the associated mount points.
The border between different LVs do not need to be aligned with any partition border.
See the border between LV 1 and LV 2 in this example.
LVM features:
• Several hard disks or partitions can be combined in a large logical volume.
• Provided the configuration is suitable, an LV (such as /usr) can be enlarged if
free space is exhausted.
• With LVM, it is possible to add hard disks or LVs in a running system. However,
this requires hot-swappable hardware.
• It is possible to activate a "striping mode" that distributes the data stream of a LV
over several PVs. If these PVs reside on different disks, the read and write performance is enhanced, as with RAID 0.
• The snapshot feature enables consistent backups (especially for servers) of the running system.
294
Deployment Guide
With these features, LVM is ready for heavily used home PCs or small servers. LVM
is well-suited for the user with a growing data stock (as in the case of databases, music archives, or user directories). This would allow file systems that are larger than the
physical hard disk. Another advantage of LVM is that up to 256 LVs can be added.
However, working with LVM is different from working with conventional partitions.
Instructions and further information about configuring LVM is available in the official LVM HOWTO at http://tldp.org/HOWTO/LVM-HOWTO/.
Starting from Kernel version 2.6, LVM version 2 is available, which is backward-compatible with the previous LVM and enables the continued management of
old volume groups. When creating new volume groups, decide whether to use the
new format or the backward-compatible version. LVM 2 does not require any kernel
patches. It makes use of the device mapper integrated in kernel 2.6. This kernel only supports LVM version 2. Therefore, when talking about LVM, this section always
refers to LVM version 2.
15.2.1.1 Thin Provisioning
Starting from Kernel version 3.4, LVM supports thin provisioning. A thin-provisioned
volume has a virtual capacity and a real capacity. Virtual capacity is the volume storage capacity that is available to a host. Real capacity is the storage capacity that is allocated to a volume copy from a storage pool. In a fully allocated volume, the virtual capacity and real capacity are the same. In a thin-provisioned volume, however, the
virtual capacity can be much larger than the real capacity. If a thin-provisioned volume does not have enough real capacity for a write operation, the volume is taken offline and an error is logged.
For more general information, see http://wikibon.org/wiki/v/
Thin_provisioning.
15.2.2 LVM Configuration with YaST
The YaST LVM configuration can be reached from the YaST Expert Partitioner (see
Section 15.1, “Using the YaST Partitioner” (page 281)) within the Volume Management item in the System View pane. The Expert Partitioner allows you to edit and
delete existing partitions and also create new ones that need to be used with LVM.
The first task is to create PVs that provide space to a volume group:
1 Select a hard disk from Hard Disks.
Advanced Disk Setup
295
2 Change to the Partitions tab.
3 Click Add and enter the desired size of the PV on this disk.
4 Use Do not format partition and change the File System ID to 0x8E Linux LVM. Do
not mount this partition.
5 Repeat this procedure until you have defined all the desired physical volumes on
the available disks.
15.2.2.1 Creating Volume Groups
If no volume group exists on your system, you must add one (see Figure 15.4, “Creating a Volume Group” (page 297)). It is possible to create additional groups by
clicking on Volume Management in the System View pane, and then on Add Volume
Group. One single volume group is usually sufficient.
1 Enter a name for the VG, for example, system.
2 Select the desired Physical Extend Size. This value defines the size of a physical
block in the volume group. All the disk space in a volume group is handled in
blocks of this size.
3 Add the prepared PVs to the VG by selecting the device and clicking on Add.
Selecting several devices is possible by holding Ctrl while selecting the devices.
4 Select Finish to make the VG available to further configuration steps.
296
Deployment Guide
Figure 15.4: Creating a Volume Group
If you have multiple volume groups defined and want to add or remove PVs, select
the volume group in the Volume Management list and click Resize. In the following
window, you can add or remove PVs to the selected volume group.
15.2.2.2 Configuring Logical Volumes
After the volume group has been filled with PVs, define the LVs which the operating
system should use in the next dialog. Choose the current volume group and change to
the Logical Volumes tab. Add, Edit, Resize, and Delete LVs as needed until all space in
the volume group has been occupied. Assign at least one LV to each volume group.
Advanced Disk Setup
297
Figure 15.5: Logical Volume Management
Click Add and go through the wizard-like pop-up that opens:
1. Enter the name of the LV. For a partition that should be mounted to /home, a selfexplanatory name like HOME could be used.
2. Select the type of the LV. It can be either Normal Volume, Thin Pool, or Thin Volume. Note that you need to create a thin pool first, which can store individual thin
volumes.
3. Select the size and the number of stripes of the LV. If you have only one PV, selecting more than one stripe is not useful.
TIP
The big advantage of a thin provisioning is that the total sum of all thin volumes stored in a thin pool can exceed the size of the pool itself.
4. Choose the file system to use on the LV as well as the mount point.
By using stripes it is possible to distribute the data stream in the LV among several PVs (striping). However, striping a volume can only be done over different PVs,
each providing at least the amount of space of the volume. The maximum number of
stripes equals to the number of PVs, where Stripe "1" means "no striping". Striping
298
Deployment Guide
only makes sense with PVs on different hard disks, otherwise performance will decrease.
WARNING: Striping
YaST cannot, at this point, verify the correctness of your entries concerning
striping. Any mistake made here is apparent only later when the LVM is implemented on disk.
If you have already configured LVM on your system, the existing logical volumes can
also be used. Before continuing, assign appropriate mount points to these LVs. With
Finish, return to the YaST Expert Partitioner and finish your work there.
15.3 Soft RAID Configuration
The purpose of RAID (redundant array of independent disks) is to combine several
hard disk partitions into one large virtual hard disk to optimize performance and/or
data security. Most RAID controllers use the SCSI protocol because it can address a
larger number of hard disks in a more effective way than the IDE protocol. It is also
more suitable for the parallel command processing. There are some RAID controllers
that support IDE or SATA hard disks. Soft RAID provides the advantages of RAID
systems without the additional cost of hardware RAID controllers. However, this requires some CPU time and has memory requirements that make it unsuitable for high
performance computers.
With SUSE® Linux Enterprise Server , you can combine several hard disks into one
soft RAID system. RAID implies several strategies for combining several hard disks
in a RAID system, each with different goals, advantages, and characteristics. These
variations are commonly known as RAID levels.
Common RAID levels are:
RAID 0
This level improves the performance of your data access by spreading out blocks
of each file across multiple disk drives. Actually, this is not really a RAID, because it does not provide data backup, but the name RAID 0 for this type of system is commonly used. With RAID 0, two or more hard disks are pooled together. Performance is enhanced, but the RAID system is destroyed and your data lost
if even one hard disk fails.
Advanced Disk Setup
299
RAID 1
This level provides adequate security for your data, because the data is copied
to another hard disk 1:1. This is known as hard disk mirroring. If one disk is destroyed, a copy of its contents is available on the other one. All disks but one
could be damaged without endangering your data. However, if the damage is not
detected, the damaged data can be mirrored to the undamaged disk. This could
result in the same loss of data. The writing performance suffers in the copying
process compared to using single disk access (10 to 20 % slower), but read access
is significantly faster in comparison to any one of the normal physical hard disks.
The reason is that the duplicate data can be parallel-scanned. Generally it can be
said that Level 1 provides nearly twice the read transfer rate of single disks and
almost the same write transfer rate as single disks.
RAID 5
RAID 5 is an optimized compromise between Level 0 and Level 1, in terms of
performance and redundancy. The hard disk space equals the number of disks
used minus one. The data is distributed over the hard disks as with RAID 0. Parity blocks, created on one of the partitions, exist for security reasons. They are
linked to each other with XOR, enabling the contents to be reconstructed by the
corresponding parity block in case of system failure. With RAID 5, no more than
one hard disk can fail at the same time. If one hard disk fails, it must be replaced
as soon as possible to avoid the risk of losing data.
RAID 6
To further increase the reliability of the RAID system, it is possible to use
RAID 6. In this level, even if two disks fail, the array still can be reconstructed.
With RAID 6, at least 4 hard disks are needed to run the array. Note that when
running as software raid, this configuration needs a considerable amount of CPU
time and memory.
RAID 10 (RAID 1+0)
This RAID implementation combines features of RAID 0 and RAID 1: the data is first mirrored to separate disk arrays, which are inserted into a new RAID 0;
type array. In each RAID 1 sub-array, one disk can fail without any damage to the
data. A minimum of four disks and an even number of disks is needed to run a
RAID 10. This type of RAID is used for database application where a huge load
is expected.
Other RAID Levels
Several other RAID levels have been developed (RAID 2, RAID 3, RAID 4,
RAIDn, RAID 10, RAID 0+1, RAID 30, RAID 50, etc.), some of them being
300
Deployment Guide
proprietary implementations created by hardware vendors. These levels are not
very common and therefore are not explained here.
15.3.1 Soft RAID Configuration with YaST
The YaST RAID configuration can be reached from the YaST Expert Partitioner, described in Section 15.1, “Using the YaST Partitioner” (page 281). This partitioning
tool enables you to edit and delete existing partitions and create new ones to be used
with soft RAID:
1 Select a hard disk from Hard Disks.
2 Change to the Partitions tab.
3 Click Add and enter the desired size of the raid partition on this disk.
4 Use Do not Format the Partition and change the File System ID to 0xFD Linux
RAID. Do not mount this partition.
5 Repeat this procedure until you have defined all the desired physical volumes on
the available disks.
For RAID 0 and RAID 1, at least two partitions are needed—for RAID 1, usually exactly two and no more. If RAID 5 is used, at least three partitions are required, RAID
6 and RAID 10 require at least four partitions. It is recommended to use partitions
of the same size only. The RAID partitions should be located on different hard disks
to decrease the risk of losing data if one is defective (RAID 1 and 5) and to optimize
the performance of RAID 0. After creating all the partitions to use with RAID, click
RAID > Add RAID to start the RAID configuration.
In the next dialog, choose between RAID levels 0, 1, 5, 6 and 10. Then, select all partitions with either the “Linux RAID” or “Linux native” type that should be used by the
RAID system. No swap or DOS partitions are shown.
TIP
For RAID types where the order of added disks matters, you can mark individual disks with one of the letters A to E. Click the Classify button, select the
disk and click one of the Class X buttons, where X is the letter you want to
assign to the disk. Assign all available RAID disks this way, and confirm with
Advanced Disk Setup
301
OK. You can easily sort the classified disks with the Sorted or Interleaved
buttons, or add a sort pattern from a text file with Pattern File.
Figure 15.6: RAID Partitions
To add a previously unassigned partition to the selected RAID volume, first click the
partition then Add. Assign all partitions reserved for RAID. Otherwise, the space on
the partition remains unused. After assigning all partitions, click Next to select the
available RAID Options.
In this last step, set the file system to use as well as encryption and the mount point
for the RAID volume. After completing the configuration with Finish, see the /dev/
md0 device and others indicated with RAID in the expert partitioner.
15.3.2 Troubleshooting
Check the file /proc/mdstat to find out whether a RAID partition has been damaged. In the event of a system failure, shut down your Linux system and replace the
defective hard disk with a new one partitioned the same way. Then restart your system and enter the command mdadm /dev/mdX --add /dev/sdX. Replace 'X'
with your particular device identifiers. This integrates the hard disk automatically into
the RAID system and fully reconstructs it.
302
Deployment Guide
Note that although you can access all data during the rebuild, you may encounter some
performance issues until the RAID has been fully rebuilt.
15.3.3 For More Information
Configuration instructions and more details for soft RAID can be found in the HOWTOs at:
• /usr/share/doc/packages/mdadm/Software-RAID.HOWTO.html
• http://raid.wiki.kernel.org
Linux RAID mailing lists are available, such as http://marc.info/?
l=linux-raid.
Advanced Disk Setup
303
Subscription Management
Any machine running SUSE Linux Enterprise Server 11 or SUSE Linux Enterprise
Desktop 11 can be configured to register against local Subscription Management Tool
server to download software updates instead of communicating directly with the Novell Customer Center and the NU servers. To use an SMT server for client registration and as a local update source, you must configure the SMT server in your network
first. The SMT server software is distributed as an add-on for SUSE Linux Enterprise
Server and its configuration is described in the Subscription Management Tool Guide.
There is no need to install any add-on on the clients to be configured for registering
against an SMT server.
16
To register a client against an SMT server, you need to equip the client with the
server's URL. As client and server communicate via the HTTPS protocol during registration, you also need to make sure the client trusts the server's certificate. In case
your SMT server is set up to use the default server certificate, the CA certificate will
be available on the SMT server via HTTP protocol at http://FQDN/smt.crt.
In this case you do not have to concern yourself with the certificate: the registration
process will automatically download the CA certificate from there, unless configured
otherwise. You must enter a path to the server's CA certificate if the certificate was
issued by an external certificate authority.
NOTE: Registering Against *.novell.com Subdomain
If you try to register against any *.novell.com subdomain, the certificate
will not be downloaded during registration (for security reasons), and certificate handling will not be done. In such cases, use a different domain name or
a plain IP address.
Subscription Management
305
There are several ways to provide this information and to configure the client machine to use SMT. The first way is to provide the needed information via kernel
parameters at boot time. The second way is to configure clients using an AutoYaST profile. There is also a script distributed with Subscription Management Tool,
clientSetup4SMT.sh, which can be run on a client to make it register against a
specified SMT server. These methods are described in the following sections:
16.1 Using Kernel Parameters to
Access an SMT Server
Any client can be configured to use SMT by providing the following kernel parameters during machine boot: regurl and regcert. The first parameter is mandatory,
the latter is optional.
regurl
URL of the SMT server. The URL needs to be in the following format:
https://FQDN/center/regsvc/ with FQDN being the fully qualified
hostname of the SMT server. It must be identical to the FQDN of the server certificate used on the SMT server. Example:
regurl=https://smt.example.com/center/regsvc/
regcert
Location of the SMT server's CA certificate. Specify one of the following locations:
URL
Remote location (http, https or ftp) from which the certificate can be downloaded. Example:
regcert=http://smt.example.com/smt.crt
Floppy
Specifies a location on a floppy. The floppy has to be inserted at boot time
(you will not be prompted to insert it if it is missing). The value must start
with the string floppy, followed by the path to the certificate. Example:
regcert=floppy/smt/smt-ca.crt
Local Path
Absolute path to the certificate on the local machine. Example:
regcert=/data/inst/smt/smt-ca.cert
306
Deployment Guide
Interactive
Use ask to open a pop-up menu during installation where you can specify
the path to the certificate. Do not use this option with AutoYaST. Example:
regcert=ask
Deactivate Certificate Installation
Use done if either the certificate will be installed by an add-on product, or
if you are using a certificate issued by an official certificate authority. Example:
regcert=done
WARNING: Beware of Typing Errors
Make sure the values you enter are correct. If regurl has not been specified correctly, the registration of the update source will fail.
If a wrong value for regcert has been entered, you will be prompted for
a local path to the certificate. In case regcert is not specified at all, it will
default to http://FQDN/smt.crt with FQDN being the name of the SMT
server.
WARNING: Change of SMT Server Certificate
If the SMT server gets a new certificate from a new and untrusted CA, the
clients need to fetch the new CA certificate file. This is done automatically
with the registration process but only if a URL was used at installation time
to retrieve the certificate, or if the regcert parameter was omitted and thus,
the default URL is used. If the certificate was loaded using any other method
(such as floppy or local path), the CA certificate will not be updated.
16.2 Configuring Clients Using
AutoYaST Profile
Clients can be configured to register with SMT server via AutoYaST profile. For general information about creating AutoYaST profiles and preparing automatic installation, refer to Chapter 21, Automated Installation (page 343). In this section, only
SMT specific configuration is described.
Subscription Management
307
To configure SMT specific data using AutoYaST, follow these steps:
1 As root, start YaST and select Miscellaneous > Autoinstallation to start the graphical AutoYaST front-end.
From a command line, you can start the graphical AutoYaST front-end with the
yast2 autoyast command.
2 Open an existing profile using File > Open, create a profile based on the current
system's configuration using Tools > Create Reference Profile, or just work with an
empty profile.
3 Select Support > Novell Customer Center Configuration. An overview of the current
configuration is shown.
4 Click Edit.
5 To register while installing automatically, select Run Product Registration. You can
include information from your system with Hardware Profile and Optional Information.
6 Set the URL of the SMT Server and, optionally, the location of the SMT Certificate. The possible values are the same as for the kernel parameters regurl
and regcert (see Section 16.1, “Using Kernel Parameters to Access an SMT
Server” (page 306)). The only exception is that the ask value for regcert
does not work in AutoYaST, because it requires user interaction. If using it, the
registration process will be skipped.
7 Perform all other configuration needed for the systems to be deployed.
8 Select File > Save As and enter a filename for the profile, such as
autoinst.xml.
16.3 Configuring Clients Using the
clientSetup4SMT.sh Script
The /usr/share/doc/packages/smt/clientSetup4SMT.sh script is
provided with SMT. This script allows to configure a client machine to use a SMT
server or to reconfigure it to use a different SMT server.
308
Deployment Guide
To configure a client machine to use SMT with the clientSetup4SMT.sh script,
follow these steps:
1 Copy the /usr/share/doc/packages/smt/clientSetup4SMT.sh
script from your SMT server to the client machine.
2 As root, execute the script on the client machine. The script can be executed in two ways. In the first case, the script name is followed by the registration URL: ./clientSetup4SMT.sh registration_URL, for example, ./clientSetup4SMT.sh https://smt.example.com/center/regsvc. In the second case, the script name is followed by the --host option followed by hostname of the SMT server: ./clientSetup4SMT.sh -host server_hostname, for example, ./clientSetup4SMT.sh -host smt.example.com.
IMPORTANT: The --host Parameter
The hostname that needs to be provided with the --host parameter, needs to be the same name the certificate is issued for. Furthermore, if the name in the certificate is the fully qualified hostname (e.g.
smt.example.com), it needs to be entered as such—entering the “short”
name (smt) will cause the clientSetup4SMT.sh script to fail.
3 The script downloads the server's CA certificate. Accept it by pressing y.
4 The script performs all necessary modifications on the client. However, the registration itself is not performed by the script.
5 Perform a registration by executing suse_register or running yast2
inst_suse_register module on the client.
16.4 Registering Clients Against
SMT Test Environment
To configure a client to register against the test environment instead the production
environment, modify /etc/suseRegister.conf on the client machine by setting:
register = command=register&testenv=1
Subscription Management
309
For more information about using SMT with a test environment, refer to the Subscription Management Tool Guide.
310
Deployment Guide
Part III. Imaging and
Creating Products
17
KIWI
KIWI is a system for creating operating system images. An image is a directory with
a file containing the operating system, its applications and configurations, the file system structure of the OS, possible additional metadata, and (depending on the image
type) also disk geometry and partition table data. With KIWI you can create LiveCDs
and LiveDVDs, USB sticks, virtual disk to play in full virtual systems like VMware,
XEN images for paravirtualization in a hypervisor, and a PXE environment to boot
from network.
17.1 Prerequisites for KIWI
To build images with KIWI, you need the following preconditions:
1. Free sufficient disk space for the operation.
2. KIWI is split into several packages, targeted to different image types. In any case,
you need the base package kiwi. Depending on your target image, you need the
following packages:
Image Type
Package Name
Installation Media
kiwi-desc-oemboot
Virtualization
kiwi-desc-xenboot
KIWI
313
Image Type
Package Name
USB Sticks
kiwi-desc-usbboot
Network Client
kiwi-desc-netboot
3. Install the kiwi-doc package. You can find some example configurations to get
an idea about structure and content.
4. Know the KIWI configuration file and its structure. It is based on a RELAX NG
schema and documented in the kiwi package under /usr/share/doc/pack​
ages/kiwi/kiwi.html. You need this document, if you want to create the
configuration file from scratch or when you want to insert elements or attributes.
17.2 Knowing KIWI’s Build Process
The building process of KIWI is separated into three steps:
1. Physical Extend (Preparation) This stage prepares the content of your new file
system. During this step the root directory is created, you determine which packages are installed on your image and which user configuration files are included.
2. Logical Extend (Creation) This stage requires a successful preparation step. The
logical extend step creates the operating system image based on the first step.
3. Deployment The resulting image type can be deployed with different methods
like installed on a hard disk or played by a virtualization system (VMware, Qemu,
VirtualBox).
17.3 Image Description
KIWI needs an image description to build an image type. The image description is a
directory which contains at least a file config.xml, or alternatively with the extension *.kiwi.
314
Deployment Guide
17.3.1 Contents of Image Description
The following table contains additional optional information. However, most of this
information is mandatory for the later functionality of the operating system:
Table 17.1: Additional Files and Directories For Image Description
File/Directory
Description
config/
optional subdirectory. Contains Bash
scripts which are executed after the
installation of all the image packages.
config.sh
optional configuration script while
creating the physical extend
config.xml
configuration file for each image description, explained in
Section 17.3.2 (page 316)
config-cdroot.tgz
archive, only used for ISO images
config-cdroot.sh
manipulate extracted data from con​
fig-cdroot.tgz
config-yast-autoyast.xml
configuration file created by AutoYaST
config-yast-firstboot.xml
configuration file for controlling the
YaST firstboot service
images.sh
optional configuration script while
creating the preparation step
root/
contains other directories, special
files, and scripts which are changed
after the installation of all image
packages
KIWI
315
17.3.2 The config.xml File
All information about an image description is stored in the central configuration
XML file config.xml. Each time KIWI is executed, config.xml is validated against an RELAX NG schema (see http://www.relaxng.org for more
information about this schema language). Therefore, it is recommended to use an
adequate XML editor with RELAX NG support or to use the documentation about
the schema in the HTML file /usr/share/doc/packages/kiwi/schema/
kiwi.xsd.html.
The configuration file consists of several parts:
• some description about the author, contact information, and a short explanation.
• preferences option needed for the logical extent stage.
• information about the users, their name, their home directories, and their passwords.
• links to repositories.
• a list of packages that are used for the definied image type.
• and other less important information which can be viewed in the above HTML file
of the RELAX NG schema documentation.
A skeleton of the file is shown in the following example:
Example 17.1: KIWI Configuration File
<image schemeversion="2.0" name="...">
<description type="system">
<author>...</author>
<contact>...</contact>
<specification>...</specification>
</description>
<preferences>
<type primary="true" boot="..." flags="...">iso</type>
<type boot="..." filesystem="ext3" format="vmdk">vmx</type>
<type boot="..." filesystem="ext3">xen</type>
<type boot="..." filesystem="squashfs" flags="unified">oem</type>
<version>2.7.0</version>
<size unit="M">780</size>
<packagemanager>zypper</packagemanager>
<rpm-check-signatures>False</rpm-check-signatures>
<rpm-force>False</rpm-force>
<locale>en_US.UTF-8</locale>
316
Deployment Guide
<oem-swap>no</oem-swap>
<oem-boot-title>USB</oem-boot-title>
</preferences>
<users group="users">
<user name="root" pwd="" home="/root"/>
</users>
<repository type="rpm-md">
<source path="/home/rpmdir"/>
</repository>
<packages type="image" patternPackageType="onlyRequired">
<package name="yast2-live-installer"/>
<package name="pam"/>
<!-- List of packages reduced -->
</packages>
The root element of every KIWI configuration file. Each file requires the version number. An optional kiwirevision attribute can be used to specify an
SVN revision of KIWI.
Contains mandatory descriptions with information about the creator of this image descriptions, its contact address and a short explanation.
Contains mandatory preferences with information about the version of this image, the used package manager, the supported image types, and other settings.
The optional users element contains a list of all users which are added to the
image. The user element contains the name, the path to its home directory,
password, and the shell.
Contains a mandatory list of repositories used by the package manager.
Contains a mandatory list of packages which are included into the image.
More details about the configuration file is shown in the HTML page above.
17.4 Creating Appliances with KIWI
This section describes how to create appliances with KIWI. An appliance is an especially-designed operating system for a specific task. For example, you can create an
appliance with the focus on office programs.
17.4.1 Creating a Local Installation
Source
All examples in kiwi-doc packages need a valid installation source to create an
image. Usually the examples connect to a network resource. The higher the network
KIWI
317
bandwidth, the faster the image creation. If you do not have a fast network or you do
not want to use it, create a local installation resource. Proceed as follows:
1 Collect your installation DVD.
2 Open a shell and become root.
3 Create the directory for your local installation directory. The examples use usually the path /image/CDs/full-VERSION-ARCH. Replace the placeholders
VERSION and ARCH with the respective values.
4 Mount the medium. Replace the DRIVE placeholder with the respective device
(usually dvd, cdrom, etc.):
mount -o loop /dev/DRIVE /mnt
5 Copy all the content of the medium into the installation directory:
cp -a /mnt/* /images/CDs/full-VERSION-ARCH
To use the local installation source, all you need to do is to enable it in the repository element:
<repository type="...">
<!-- Remove the comment markers in the next line -->
<!-- <source path="/image/CDs/full-VERSION-ARCH" -->
<source path="opensuse://openSUSE:11.0/standard"/>
</repository>
17.4.2 Creating an Image
An image is a virtual disk image containing all partitions, boot loader information,
and packages as it resides on a real disk. To create an ISO image, proceed as follows:
1 Install the packages kiwi and kiwi-doc and resolve any dependencies.
2 Open a shell and become root.
3 Copy the directory /usr/share/doc/packages/kiwi/exam​
ples/suse-11.0/suse-oem-preload to your current directory.
4 Open the file config.xml and locate the element repository. If you want to
use a local installation source, refer to Section 17.4.1 (page 317) for more information.
318
Deployment Guide
5 Execute KIWI with the following command to prepare the first stage (“physical extend”):
kiwi --prepare suse-oem-preload --root oem
6 Build the ISO image:
kiwi --create oem --type iso --destdir /tmp/myoem
17.4.3 Creating Preload Image with NFS
To create an image with NFS functionality, proceed as follows:
1 Open a shell and become root.
2 Copy the directory /usr/share/doc/packages/kiwi/exam​
ples/suse-11.1/suse-oem-preload to your current directory.
3 Open the file suse-oem-preload/config.xml and locate the packages
element with the attribute type="image".
4 Insert the following line between <packages type="image"> and </
packages> and save the file:
<package name="nfs-client"/>
5 Rebuild the image as described in Step 5 (page 319).
17.5 For More Information
Find more information in the following documents on the KIWI Portal at http://
en.opensuse.org/Portal:KIWI.
KIWI
319
Creating Add-On Products
With Add-on Creator
18
An Add-On is a special designed media, usually a CD or DVD, to extend your product. The Add-on Creator was developed to support our customers and partners and
simplify third-party software distribution for all SUSE products.
18.1 Creating Images
To create an Add-On CD, proceed as follows:
1 Start YaST and open the Add-On Creator module. A window opens.
2 If you have not run this module before, click on Create an Add-On from the Beginning to start. In case you have already created an Add-On, the window shows
a list of all created Add-Ons. Click Add to start.
3 Enter the product name and version of your Add-On and give some further options:
• Choose the required product upon which it is based.
• Select the path to additional Add-On packages. You need this, if you need
further RPM packages which are not included in your base product (this step
is optional).
• Select the path with the required product packages (this step is optional).
Creating Add-On Products With Add-on Creator
321
4 Correct the product definition and enter a vendor name. Disable Show Only Required Keywords to display more keywords.
5 Change the package descriptions. Use Add Language to insert a new language
and add translated descriptions (this step is optional).
6 Add new patterns. With patterns you can group your RPM packages. Use New
to add a new pattern name and change the respective attributes in the list below
(this step is optional).
7 Modify the output settings. Enter a path to your output directory and change the
name of the ISO name (changing the name of the ISO is optional). Additionally,
you can modify further features:
• Use Configure Workflow... to enter files to customize your product workflow.
• Use Optional Files... to add files to your Add-On product. The first part can
be used to insert information about the Add-On in the info.txt file. Use
the license files to display a window with Agree and Disagree buttons before
the installation starts. More files can be added in the README section.
The second part can be used to store COPYRIGHT and COPYING files in various languages.
8 Sign your Add-On product with your GPG key. Signing your product with your
GPG key provides evidence of the origin of your product. If you do not have a
key, create one first and enter the respective passphrase twice.
9 Check your product in the overview and proceed with Finish.
10 Use the Build button to start the process. Finish closes the window.
18.2 Add-On Structure
If you create an Add-On product, the following overview contains the structure of the
files and directories:
ARCHIVES.gz
Contains the gzipped contents of all RPM files. It is actually a listing of the rpm
command with the options -qil for each RPM file.
322
Deployment Guide
Changelog
Contains all the changes of the RPM files.
content
Contains information about your Add-On product.
content.asc
Contains the signature file from GPG.
content.key, gpg-pubkey-NUMBER.asc
The public GPG key.
INDEX.gz
Contains a list of all RPM files and packed with gzip.
ls-lR.gz
Contains a list of all files and directories of your Add-On product medium.
media.N/
Contains files with basic information about the Add-On media set. The directory is numered, so media.1/ is for the first Add-On medium. Additional media
have a consecutive number.
suse/
Contains sub directories with architecture-specific information. Exceptions are
noarch/ for architecture-independent packages, and src/ for source packages. Proprietary software packages are stored under nosrc/.
18.3 For More Information
Find more information in the following documents on the KIWI Portal at http://
en.opensuse.org/Portal:KIWI.
Creating Add-On Products With Add-on Creator
323
Creating Images with YaST
Product Creator
19
The YaST Product Creator is a unified graphical front-end for KIWI and Add-on
Creator. It was developed to provide image creation functionality in one place. All
tools integrated in the YaST Product Creator are also available as separate YaST modules or applications.
19.1 Prerequisites for Product
Creator
Before you can create images with the YaST Product Creator, make sure you meet the
following prerequisites:
1. Install the package yast2-product-creator from the SUSE
Linux Enterprise Software Development Kit (SDK) under http://
download.suse.com/. This package needs other packages. Make sure you
fullfill all dependencies.
2. Free sufficient disk space for the operation.
19.2 Creating Images
The Product Creator uses KIWI to create an image of a product. In case you are interested in manually developing such images, refer to Chapter 17, KIWI (page 313).
Creating Images with YaST Product Creator
325
To create an image, proceed as follows:
1 If you are starting the Product Creator for the first time, enter the configuration
name and choose the method for adding packages to the ISO image.
If you have used the Product Creator already, select Add to create a new product
definition and enter the configuration name and choose the method.
2 Select or deselect package sources. To select a source, select it from the table and
click Select. With Create New... execute the Add-on Creator, see Chapter 18, Creating Add-On Products With Add-on Creator (page 321) for more information. To
add a different source, add the source in the YaST Installation Sources module first
then run the Product Creator again. After source selection, click Next.
NOTE: Unsupported Target Architectures
Do not change the target architecture. KIWI does not presently support the
building of different architectures.
3 Enter the path in which to create the skeleton directory. Choose whether to Generate ISO Image File or Create Directory Tree Only. Use the other options to insert
metadata. Click Next.
4 Edit the content of the isolinux.cfg file, if it is a part of the configuration. In
most cases you can leave it as it is. If the file is not part of the configuration, add it
now with Load File. Click Next.
5 Select your software. All package dependencies are solved automatically after Apply is clicked.
6 Sign your product with Digitally Sign the Product on the Medium, if needed. Provide a key for your product configuration. Signing your product with your GPG
key provides evidence of the origin of your product. After key configuration, click
Next.
7 Review the summary. To change any option, use Back. To confirm your new product configuration, click Finish.
Your product definition is now completed. The Product Creator allows you to choose
from the following actions:
326
Deployment Guide
• Create Product Creates an ISO image of the selected product. If there is something missing, the process will be aborted. Correct the error and repeat the configuration.
• Create Image with KIWI... Use the pull-down menu to choose from different target formats, such as Live media or Xen images.
19.3 For More Information
Find more information about creating system images and related topics in the following documents:
• Chapter 17, KIWI (page 313)
• http://en.opensuse.org/Portal:KIWI—The KIWI project
• KIWI documentation: /usr/share/doc/packages/kiwi/kiwi.pdf
Creating Images with YaST Product Creator
327
Deploying Customized
Preinstallations
20
Rolling out customized preinstallations of SUSE Linux Enterprise Server to a large
number of identical machines spares you from installing each one of them separately
and provides a standardized installation for the end users. With YaST Firstboot, create
customized preinstallation images and determine the workflow for the final personalization steps that involve end user interaction (as opposed to AutoYaST, which allows
completely automated installations; for more information, see Chapter 21, Automated
Installation (page 343)).
Creating a custom installation, rolling it out to your hardware, and personalizing the
final product involves the following steps:
1 Prepare the master machine whose disk needs to be cloned to the client machines. For more information, refer to Section 20.1, “Preparing the Master
Machine” (page 330).
2 Customize the firstboot workflow. For more information, refer to Section 20.2,
“Customizing the Firstboot Installation” (page 330).
3 Clone the master machine's disk and roll this image out to the clients'
disks. For more information, refer to Section 20.3, “Cloning the Master
Installation” (page 339).
4 Have the end user personalize the instance of SUSE Linux Enterprise
Server. For more information, refer to Section 20.4, “Personalizing the
Installation” (page 339).
Deploying Customized Preinstallations
329
20.1 Preparing the Master Machine
To prepare a master machine for a firstboot workflow, proceed as follows:
1 Insert the installation media into the master machine.
2 Boot the machine.
3 Perform a normal installation including all necessary configuration steps and wait
for the installed machine to boot. Also install the yast2-firstboot package.
4 To define your own workflow of YaST configuration steps for the end user or
to add your own YaST modules to this workflow, proceed to Section 20.2, “Customizing the Firstboot Installation” (page 330). Otherwise proceed directly to
Step 5 (page 330).
5 Enable firstboot as root:
Create an empty file /var/lib/YaST2/reconfig_system to trigger
firstboot's execution. This file will be deleted once the firstboot configuration has
been successfully accomplished. Create this file using the following command:
touch /var/lib/YaST2/reconfig_system
6 Proceed to Section 20.3, “Cloning the Master Installation” (page 339).
20.2 Customizing the Firstboot
Installation
Customizing the firstboot installation workflow may involve several different components. Customizing them is optional. If you do not make any changes, firstboot performs the installation using the default settings. The following options are available:
• Customizing messages to the user, as described in Section 20.2.1, “Customizing
YaST Messages” (page 331).
• Customizing licenses and license actions, as described in Section 20.2.2, “Customizing the License Action” (page 332).
330
Deployment Guide
• Customizing the release notes to display, as described in Section 20.2.3, “Customizing the Release Notes” (page 333).
• Customizing the order and number of components involved in the installation, as
described in Section 20.2.4, “Customizing the Workflow” (page 333).
• Configuring additional optional scripts, as described in Section 20.2.5, “Configuring Additional Scripts” (page 338).
To customize any of these components, modify the following configuration files:
/etc/sysconfig/firstboot
Configure various aspects of firstboot (such as release notes, scripts, and license
actions).
/etc/YaST2/firstboot.xml
Configure the installation workflow by enabling or disabling components or
adding custom ones.
Provide translations for such a customized installation workflow, as described in Section 20.2.6, “Providing Translations of the Installation
Workflow” (page 338).
If you want to customize more than just the workflow components, refer the control.xml documentation at http://
doc.opensuse.org/projects/YaST/SLES11/tdg/
inst_in_general_chap.html#product_control.
20.2.1 Customizing YaST Messages
By default, an installation of SUSE Linux Enterprise Server contains several default
messages that are localized and displayed at certain stages of the installation process.
These include a welcome message, a license message, and a congratulatory message
at the end of installation. You can replace any of these with your own versions and
include localized versions of them in the installation. To include your own welcome
message, proceed as follows:
1 Log in as root.
2 Open the /etc/sysconfig/firstboot configuration file and apply the following changes:
Deploying Customized Preinstallations
331
2a Set FIRSTBOOT_WELCOME_DIR to the directory path where you want to
store the files containing the welcome message and the localized versions,
for example:
FIRSTBOOT_WELCOME_DIR="/usr/share/firstboot/"
2b If your welcome message has filenames other than welcome.txt
and welcome_locale.txt (where locale matches the ISO 639
language codes such as “cs” or “de”), specify the filename pattern in
FIRSTBOOT_WELCOME_PATTERNS. For example:
FIRSTBOOT_WELCOME_PATTERNS="mywelcome.txt"
If unset, the default value of welcome.txt is assumed.
3 Create the welcome file and the localized versions and place them in the directory
specified in the /etc/sysconfig/firstboot configuration file.
Proceed in a similar way to configure customized license and finish messages. These
variables are FIRSTBOOT_LICENSE_DIR and FIRSTBOOT_FINISH_FILE.
Change the SHOW_Y2CC_CHECKBOX to “yes” if the user needs to be able to start
YaST directly after performing the installation.
20.2.2 Customizing the License Action
You can customize the way the installation system reacts to a user's refusal to accept
the license agreement. There are three different ways which the system could react to
this scenario:
halt
The firstboot installation is aborted and the entire system shuts down. This is the
default setting.
continue
The firstboot installation continues.
abort
The firstboot installation is aborted, but the system attempts to boot.
Make your choice and set LICENSE_REFUSAL_ACTION to the appropriate value.
332
Deployment Guide
20.2.3 Customizing the Release Notes
Depending on if you have changed the instance of SUSE Linux Enterprise Server you
are deploying with firstboot, you probably need to educate the end users about important aspects of their new operating system. A standard installation uses release notes
(displayed during one of the final stages of the installation) to provide important information to the users. To have your own modified release notes displayed as part of a
firstboot installation, proceed as follows:
1 Create your own release notes file. Use the RTF format as in the example
file in /usr/share/doc/release-notes and save the result as RE​
LEASE-NOTES.en.rtf (for English).
2 Store optional localized versions next to the original version and replace the en
part of the filename with the actual ISO 639 language code, such as de for German.
3 Open the firstboot configuration file from /etc/sysconfig/firstboot and
set FIRSTBOOT_RELEASE_NOTES_PATH to the actual directory where the release notes files are stored.
20.2.4 Customizing the Workflow
By default, a standard firstboot workflow includes the following components:
• Language Selection
• Welcome
• License Agreement
• Host Name
• Network
• Time and Date
• Desktop
• root Password
• User Authentication Method
Deploying Customized Preinstallations
333
• User Management
• Hardware Configuration
• Finish Setup
This standard layout of a firstboot installation workflow is not mandatory. You can
enable or disable certain components or integrate your own modules into the workflow. To modify the firstboot workflow, manually edit the firstboot configuration
file /etc/YaST2/firstboot.xml. This XML file is a subset of the standard
control.xml file that is used by YaST to control the installation workflow.
For an overview about proposals, see Example 20.1, “Configuring the Proposal
Screens” (page 334). This provides you with enough background to modify the
firstboot installation workflow. The basic syntax of the firstboot configuration file
(plus how the key elements are configured) is explained with this example.
Example 20.1: Configuring the Proposal Screens
…
<proposals config:type="list">
<proposal>
<name>firstboot_hardware</name>
<mode>installation</mode>
<stage>firstboot</stage>
<label>Hardware Configuration</label>
<proposal_modules config:type="list">
<proposal_module>printer</proposal_module>
</proposal_modules>
</proposal>
<proposal>
…
</proposal>
</proposals>
The container for all proposals that should be part of the firstboot workflow.
The container for an individual proposal.
The internal name of the proposal.
The mode of this proposal. Do not make any changes here. For a firstboot installation, this must be set to installation.
The stage of the installation process at which this proposal is invoked. Do not
make any changes here. For a firstboot installation, this must be set to firstboot.
334
Deployment Guide
The label to be displayed on the proposal.
The container for all modules that are part of the proposal screen.
One or more modules that are part of the proposal screen.
The next section of the firstboot configuration file consists of the workflow definition. All modules that should be part of the firstboot installation workflow must be
listed here.
Example 20.2: Configuring the Workflow Section
<workflows config:type="list">
<workflow>
<defaults>
<enable_back>yes</enable_back>
<enable_next>yes</enable_next>
<archs>all</archs>
</defaults>
<stage>firstboot</stage>
<label>Configuration</label>
<mode>installation</mode>
… <!–– list of modules ––>
</modules>
</workflow>
</workflows>
…
The overall structure of the workflows section is very similar to that of the proposals section. A container holds the workflow elements and the workflow elements all include stage, label and mode information (just as the proposals introduced
in Example 20.1, “Configuring the Proposal Screens” (page 334)). The most notable difference is the defaults section, which contains basic design information
for the workflow components:
enable_back
Include the Back button in all dialogs.
enable_next
Include the Next button in all dialogs.
archs
Specify the hardware architectures on which this workflow should be used.
Example 20.3: Configuring the List of Workflow Components
Deploying Customized Preinstallations
335
<modules config:type="list">
<module>
<label>Language</label>
<enabled config:type="boolean">false</enabled>
<name>firstboot_language</name>
</module>
<modules>
The container for all components of the workflow.
The module definition.
The label displayed with the module.
The switch to enable or disable this component in the workflow.
The module name. The module itself must be located under /usr/share/
YaST2/clients and have the .ycp file suffix.
To make changes to the number or order of proposal screens during the firstboot installation, proceed as follows:
1 Open the firstboot configuration file at /etc/YaST2/firstboot.xml.
2 Delete or add proposal screens or change the order of the existing ones:
• To delete an entire proposal, remove the proposal element including all its
sub-elements from the proposals section and remove the respective module
element (with sub-elements) from the workflow.
• To add a new proposal, create a new proposal element and fill in all the required sub-elements. Make sure that the proposal exists as a YaST module in /
usr/share/YaST2/clients.
• To change the order of proposals, move the respective module elements containing the proposal screens around in the workflow. Note that there may be dependencies to other installation steps that require a certain order of proposals
and workflow components.
3 Apply your changes and close the configuration file.
You can always change the workflow of the configuration steps when the default does
not meet your needs. Enable or disable certain modules in the workflow (or add your
own custom ones).
To toggle the status of a module in the firstboot workflow, proceed as follows:
336
Deployment Guide
1 Open the /etc/YaST2/firstboot.xml configuration file.
2 Change the value for the enabled element from true to false to disable the
module or from false to true to enable it again.
<module>
<label>Time and Date</label>
<enabled config:type="boolean">true</enabled>
<name>firstboot_timezone</name>
</module>
3 Apply your changes and close the configuration file.
To add a custom made module to the workflow, proceed as follows:
1 Create your own YaST module and store the module file module_name.ycp in
/usr/share/YaST2/clients.
2 Open the /etc/YaST2/firstboot.xml configuration file.
3 Determine at which point in the workflow your new module should be run. In doing so, make sure that possible dependencies to other steps in the workflow are taken into account and resolved.
4 Create a new module element inside the modules container and add the appropriate sub-elements:
<modules config:type="list">
…
<module>
<label>my_module</label>
<enabled config:type="boolean">true</enabled>
<name>filename_my_module</name>
</module>
</modules>
4a Enter the label to be displayed on your module in the label element.
4b Make sure that enabled is set to true to have your module included in
the workflow.
4c Enter the filename of your module in the name element. Omit the full path
and the .ycp suffix.
5 Apply your settings and close the configuration file.
Deploying Customized Preinstallations
337
TIP: Finding Connected Network Interface For Auto-Configuration
If the target hardware may feature more than one network interface add the
network-autoconfig package to the application image. network-autoconfig makes sure that during firstboot all available ethernet interfaces
are cycled until one is successfully configured with DHCP.
20.2.5 Configuring Additional Scripts
Firstboot can be configured to execute additional scripts after the firstboot workflow
has been completed. To add additional scripts to the firstboot sequence, proceed as
follows:
1 Open the /etc/sysconfig/firstboot configuration file and make sure
that the path specified for SCRIPT_DIR is correct. The default value is /usr/
share/firstboot/scripts.
2 Create your shell script, store it in the specified directory, and apply the appropriate file permissions.
20.2.6 Providing Translations of the
Installation Workflow
Depending on the end user it could be desirable to offer translations of the customized
workflow. Those translations could be necessary, if you customized the workflow by
changing the /etc/YaST2/firstboot.xml file, as described in Section 20.2.4,
“Customizing the Workflow” (page 333). This is different from the localization of
customized YaST messages, which is already described in Section 20.2.1, “Customizing YaST Messages” (page 331).
If you have changed /etc/YaST2/firstboot.xml and introduced string
changes, generate a new translation template file (.pot file) and use the gettext
tool chain to translate and finally install the translated files in the YaST locale directories (/usr/share/YaST2/locale) as compiled .mo files. Proceed as follows:
1 Change the textdomain setting from:
<textdomain>firstboot</textdomain>
338
Deployment Guide
to, for example,
<textdomain>firstboot-oem</textdomain>
2 Use xgettext to extract the translatable strings to the translation template file
(.pot file), for example to firstboot-oem.pot:
xgettext -L Glade -o firstboot-oem.pot /etc/YaST2/firstboot.xml
3 Start the translation process. Then package the translated files (.LL_code.po
files) the same way as translations of the other projects and install the compiled
firstboot-oem.mo files.
If you need translations for additional or changed YaST modules, provide translations within such a module itself. If you just changed an existing module, make sure
to change also its text domain statement to avoid undesired side effects.
TIP: For More Information
For more information about YaST development, refer to http://
en.opensuse.org/openSUSE:YaST_development. Detailed information about YaST firstboot can be found at http://doc.opensuse.org/
projects/YaST/SLES11/tdg/bk09ch01s02.html.
20.3 Cloning the Master Installation
Clone the master machine's disk using any of the imaging mechanisms available to
you, and roll these images out to the target machines. For more information about
imaging see Chapter 17, KIWI (page 313).
20.4 Personalizing the Installation
As soon as the cloned disk image is booted, firstboot starts and the installation proceeds exactly as laid out in Section 20.2.4, “Customizing the
Workflow” (page 333). Only the components included in the firstboot workflow
configuration are started. All other installation steps are skipped. The end user adjusts language, keyboard, network, and password settings to personalize the workstaDeploying Customized Preinstallations
339
tion. Once this process is finished, a firstboot installed system behaves as any other instance of SUSE Linux Enterprise Server.
340
Deployment Guide
Part IV. Automated
Installations
Automated Installation
AutoYaST allows you to install SUSE® Linux Enterprise on a large number of machines in parallel. The AutoYaST technology offers great flexibility to adjust deployments to heterogeneous hardware. This chapter tells you how to prepare a simple automated installation and lay out an advanced scenario involving different hardware
types and installation purposes.
21
21.1 Simple Mass Installation
IMPORTANT: Identical Hardware
This scenario assumes you are rolling out SUSE Linux Enterprise to a set of
machines with exactly the same hardware configuration.
To prepare for an AutoYaST mass installation, proceed as follows:
1 Create an AutoYaST profile that contains the installation details needed for
your deployment as described in Section 21.1.1, “Creating an AutoYaST
Profile” (page 344).
2 Determine the source of the AutoYaST profile and the parameter to pass to the installation routines as described in Section 21.1.2, “Distributing the Profile and Determining the autoyast Parameter” (page 346).
3 Determine the source of the SUSE Linux Enterprise installation data as described
in Section 21.1.3, “Providing the Installation Data” (page 348).
Automated Installation
343
4 Determine and set up the boot scenario for autoinstallation as described in Section 21.1.4, “Setting Up the Boot Scenario” (page 349).
5 Pass the command line to the installation routines by adding the parameters manually or by creating an info file as described in Section 21.1.5, “Creating the info
File” (page 351).
6 Start the autoinstallation process as described in Section 21.1.6, “Initiating and
Monitoring the Autoinstallation” (page 354).
21.1.1 Creating an AutoYaST Profile
An AutoYaST profile tells AutoYaST what to install and how to configure the installed system to get a completely ready-to-use system in the end. It can be created in
several different ways:
• Clone a fresh installation from a reference machine to a set of identical machines
• Use the AutoYaST GUI to create and modify a profile to meet your requirements
• Use an XML editor and create a profile from scratch
To clone a fresh reference installation, proceed as follows:
1 Perform a normal installation.
2 After you complete the hardware configuration and read the release notes, check
Clone This System for AutoYaST, if it is not yet checked by default. This creates a
ready-to-use profile as /root/autoyast.xml that can be used to create clones
of this particular installation.
To use the AutoYaST GUI to create a profile from an existing system configuration
and modify it to your needs, proceed as follows:
1 As root, start YaST.
2 Select Miscellaneous > Autoinstallation to start the graphical AutoYaST front-end.
3 Select Tools > Create Reference Profile to prepare AutoYaST to mirror the current
system configuration into an AutoYaST profile.
344
Deployment Guide
4 As well as the default resources (like boot loader, partitioning, and software selection), you can add various other aspects of your system to the profile by checking
the items in the list in Create a Reference Control File.
5 Click Create to have YaST gather all the system information and write it to a new
profile.
6 To proceed, choose one of the following:
• If the profile is complete and matches your requirements, select File > Save as
and enter a filename for the profile, such as autoyast.xml.
• Modify the reference profile by selecting the appropriate configuration aspects
(such as “Hardware/Printer”) from the tree view to the left and clicking Configure. The respective YaST module starts but your settings are written to the AutoYaST profile instead of applied to your system. When done, select File > Save
as and enter a suitable name for the profile.
7 Leave the AutoYaST module with File > Exit.
Figure 21.1: Editing an AutoYaST Profile with the AutoYaST Front-End
Automated Installation
345
21.1.2 Distributing the Profile and
Determining the autoyast Parameter
The AutoYaST profile can be distributed in several different ways. Depending on the
protocol used to distribute the profile data, different AutoYaST parameters are used
to make the profile location known to the installation routines on the client. The location of the profile is passed to the installation routines by means of the boot prompt or
an info file that is loaded upon boot. The following options are available:
346
Profile Location
Parameter
Description
File
autoyast=file://
path
Makes the installation routines look for
the control file in the
specified path (relative to source root directory—file:///
autoyast.xml if in
the top directory of a
CD-ROM).
Device
autoyast=device:// Makes the installation
path
routines look for the
control file on a storage device. Only the
device name is needed—/dev/sda1 is
wrong, use sda1 instead.
Floppy
autoyast=floppy:// Makes the installation
path
routines look for the
control file on a floppy in the floppy drive.
This option is especially useful if you want to
boot from CD-ROM.
Deployment Guide
Profile Location
Parameter
Description
NFS
autoyast=nfs://serv​
Has the installation rouer/path
tines retrieve the control file from an NFS
server.
HTTP
autoyast=http://serv​
Has the installation rouer/path
tines retrieve the control file from an HTTP
server.
HTTPS
autoyast=https://serv​
Has the installation
er/path
routines retrieve the
control file from an
HTTPS server.
TFTP
autoyast=tftp://serv​
Has the installation rouer/path
tines retrieve the control file from a TFTP
server.
FTP
autoyast=ftp://serv​
Has the installation rouer/path
tines retrieve the control file from an FTP
server.
Replace the server and path placeholders with values matching your actual setup.
AutoYaST includes a feature that allows the binding of certain profiles to the client's
MAC address. Without having to alter the autoyast= parameter, you can have the
same setup install several different instances using different profiles.
To use this, proceed as follows:
1 Create separate profiles with the MAC address of the client as the filename and put
them on the HTTP server that holds your AutoYaST profiles.
2 Omit the exact path including the filename when creating the autoyast= parameter, for example:
Automated Installation
347
autoyast=tftp://192.168.1.115/
3 Start the autoinstallation.
YaST tries to determine the location of the profile in the following way:
1. YaST searches for the profile using its own IP address in uppercase hexadecimal,
for example, 192.0.2.91 is C000025B.
2. If this file is not found, YaST removes one hex digit and tries again. This action is
repeated eight times until the file with the correct name is found.
3. If that still fails, it tries locating a file with the MAC address of the clients as the
filename. The MAC address of the example client is 0080C8F6484C.
4. If the MAC address–named file cannot be found, YaST searches for a file named
default (in lowercase). An example sequence of addresses where YaST searches
for the AutoYaST profile looks as follows:
C000025B
C000025
C00002
C0000
C000
C00
C0
C
0080C8F6484C
default
21.1.3 Providing the Installation Data
The installation data can be provided by means of the product CDs or DVDs or using
a network installation source. If the product CDs are used as the installation source,
physical access to the client to be installed is needed, because the boot process needs
to be initiated manually and the CDs need to be changed.
To provide the installation sources over the network, set up a network installation
server (HTTP, NFS, FTP) as described in Section 14.2.1, “Setting Up an Installation
Server Using YaST” (page 254). Use an info file to pass the server's location to the
installation routines.
348
Deployment Guide
21.1.4 Setting Up the Boot Scenario
The client can be booted in several different ways:
Network Boot
As with a normal remote installation, autoinstallation can be initiated with Wake
on LAN and PXE, the boot image and control file can be pulled in via TFTP, and
the installation sources from any network installation server.
Bootable CD-ROM
You can use the original SUSE Linux Enterprise media to boot the system for autoinstallation and pull in the control file from a network location or a floppy. Alternately, create your own custom CD-ROM holding both the installation sources
and the AutoYaST profile.
The following sections provide a basic outline of the procedures for network boot or
boot from CD-ROM.
21.1.4.1 Preparing for Network Boot
Network booting with Wake on LAN, PXE, and TFTP is discussed in Section 14.1.3,
“Remote Installation via VNC—PXE Boot and Wake on LAN” (page 249). To make
the setup introduced there work for autoinstallation, modify the featured PXE Linux
configuration file (/srv/tftp/pxelinux.cfg/default) to contain the autoyast parameter pointing to the location of the AutoYaST profile. An example entry for a standard installation looks like this:
default linux
# default label linux
kernel linux
append initrd=initrd install=http://192.168.1.115/install/suseenterprise/
The same example for autoinstallation looks like this:
default linux
# default label linux
kernel linux
append initrd=initrd install=http://192.168.1.115/install/suseenterprise/ \
autoyast=nfs://192.168.1.110/profiles/autoyast.xml
Automated Installation
349
Replace the example IP addresses and paths with the data used in your setup.
21.1.4.2 Preparing to Boot from CD-ROM
There are several ways in which booting from CD-ROM can come into play in AutoYaST installations. Choose from the following scenarios:
Boot from SUSE Linux Enterprise Media, Get the Profile over the Network
Use this approach if a totally network-based scenario is not possible (for example,
if your hardware does not support PXE) and you have physical access to system
to install during most of the process.
You need:
• The SUSE Linux Enterprise media
• A network server providing the profile data (see Section 21.1.2, “Distributing the Profile and Determining the autoyast Parameter” (page 346)
for details)
• A floppy containing the info file that tells the installation routines where
to find the profile
or
Access to the boot prompt of the system to install where you manually enter the autoyast= parameter
Boot and Install from SUSE Linux Enterprise Media, Get the Profile from a Floppy
Use this approach if an entirely network-based installation scenario would not
work. It requires physical access to the system to be installed for turning on the
target machine, or, in the second case, to enter the profile's location at the boot
prompt. In both cases, you may also need to change media depending on the
scope of installation.
You need:
• The SUSE Linux Enterprise media
• A floppy holding both the profile and the info file
or
350
Deployment Guide
Access to the boot prompt of the target to enter the autoyast= parameter
Boot and Install from Custom Media, Get the Profile from the Media
If you just need to install a limited number of software packages and the number
of targets is relatively low, creating your own custom CD holding both the installation data and the profile itself might prove a good idea, especially if no network
is available in your setup.
21.1.5 Creating the info File
The installation routines at the target need to be made aware of all the different components of the AutoYaST framework. This is done by creating a command line containing all the parameters needed to locate the AutoYaST components, installation
sources, and the parameters needed to control the installation process.
Do this by manually passing these parameters at the boot prompt of the installation or
by providing a file called info that is read by the installation routines (linuxrc). The
former requires physical access to any client to install, which makes this approach
unsuitable for large deployments. The latter enables you to provide the info file
on some media that is prepared and inserted into the clients' drives prior to the autoinstallation. Alternatively, use PXE boot and include the linuxrc parameters in the
pxelinux.cfg/default file as shown in Section 21.1.4.1, “Preparing for Network Boot” (page 349).
The following parameters are commonly used for linuxrc. For more information, refer to the AutoYaST package documentation under /usr/share/doc/pack​
ages/autoyast.
IMPORTANT: Separating Parameters and Values
When passing parameters to linuxrc at the boot prompt, use = to separate
parameter and value. When using an info file, separate parameter and value with :.
Keyword
Value
netdevice
The network device to use for network setup (for BOOTP/DHCP reAutomated Installation
351
Keyword
Value
quests). Only needed if several network devices are available.
352
hostip
When empty, the client sends a
BOOTP request. Otherwise the client
is configured using the specified data.
netmask
Netmask for the selected network.
gateway
Default gateway.
nameserver
Name server.
autoyast
Location of the the control file to use
for the automatic installation, such as
autoyast=nfs//192.168.1.110/
profiles/.
install
Location of the installation source, such as
install=nfs://192.168.1.110/
CDs/.
vnc
If set to 1, enables VNC remote controlled installation.
vncpassword
The password for VNC.
usessh
If set to 1, enables SSH remote controlled installation.
netsetup
If set to 1, sets up the network. Normally this is done automatically, but
you need to set netsetup=1 in case
the installation repository is provided
locally (e.g. via DVD or local iso im-
Deployment Guide
Keyword
Value
age) and the info file is loaded from
the network.
If your autoinstallation scenario involves client configuration via DHCP and a network installation source, and you want to monitor the installation process using VNC,
your info would look like this:
autoyast:profile_source install:install_source vnc:1
vncpassword:some_password
If you prefer a static network setup at installation time, your info file would look
like the following:
autoyast:profile_source \
install:install_source \
hostip:some_ip \
netmask:some_netmask \
gateway:some_gateway
The \ indicates that the line breaks have only been added for the sake of readability.
All options must be entered as one continuous string.
The info data can be made available to linuxrc in various different ways:
• As a file on a floppy or CD Rom that is in the client's drive at installation time. Add
the info parameter similar to info=floppy:/info or info=cd:/info.
• As a file in the root directory of the initial RAM disk used for booting the system
provided either from custom installation media or via PXE boot.
• As part of the AutoYaST profile. In this case, the AutoYaST file needs to be called
info to enable linuxrc to parse it. An example for this approach is given below.
• By means of an URL that points to the location of the info file. The syntax for this
looks like info=http://www.example.com/info.
linuxrc looks for a string (start_linuxrc_conf) in the profile that represents
the beginning of the file. If it is found, it parses the content starting from that string
and finishes when the string end_linuxrc_conf is found. The options are stored
in the profile as follows:
....
<install>
....
Automated Installation
353
<init>
<info_file>
<![CDATA[
#
# Don't remove the following line:
# start_linuxrc_conf
#
install: nfs:server/path
vnc: 1
vncpassword: test
autoyast: file:///info
# end_linuxrc_conf
# Do not remove the above comment
#
]]>
</info_file>
</init>
......
</install>
....
linuxrc loads the profile containing the boot parameters instead of the traditional in​
fo file. The install: parameter points to the location of the installation sources.
vnc and vncpassword indicate the use of VNC for installation monitoring. The
autoyast parameter tells linuxrc to treat info as an AutoYaST profile.
21.1.6 Initiating and Monitoring the
Autoinstallation
After you have provided all the infrastructure mentioned above (profile, installation
source, and info file), you can go ahead and start the autoinstallation. Depending on
the scenario chosen for booting and monitoring the process, physical interaction with
the client may be needed:
• If the client system boots from any kind of physical media, either product media or
custom CDs, you need to insert these into the client's drives.
• If the client is not switched on via Wake on LAN, you need to at least switch on the
client machine.
• If you have not opted for remote controlled autoinstallation, the graphical feedback
from AutoYaST is sent to the client's attached monitor or, if you use a headless
client, to a serial console.
354
Deployment Guide
To enable remote controlled autoinstallation, use the VNC or SSH parameters described in Section 21.1.5, “Creating the info File” (page 351) and connect to the
client from another machine as described in Section 14.5, “Monitoring the Installation
Process” (page 277).
21.2 Rule-Based Autoinstallation
The following sections introduce the basic concept of rule-based installation using
AutoYaST and provide an example scenario that enables you to create your own custom autoinstallation setup.
21.2.1 Understanding Rule-Based
Autoinstallation
Rule-based AutoYaST installation allows you to cope with heterogeneous hardware
environments:
• Does your site contain hardware of different vendors?
• Are the machines on your site of different hardware configuration (for example,
using different devices or using different memory and disk sizes)?
• Do you intend to install across different domains and need to distinguish between
them?
What rule-based autoinstallation does is, basically, generate a custom profile to match
a heterogeneous scenario by merging several profiles into one. Each rule describes
one particular distinctive feature of your setup (such as disk size) and tells AutoYaST
which profile to use when the rule matches. Several rules describing different features of your setup are combined in an AutoYaST rules.xml file. The rule stack
is then processed and AutoYaST generates the final profile by merging the different
profiles matching the AutoYaST rules into one. To illustrate this procedure, refer to
Section 21.2.2, “Example Scenario for Rule-Based Autoinstallation” (page 357).
Rule-based AutoYaST offers you great flexibility in planning and executing your
SUSE Linux Enterprise deployment. You can:
Automated Installation
355
• Create rules for matching any of the predefined system attributes in AutoYaST
• Combine multiple system attributes (such as disk size and kernel architecture) into
one rule by using logical operators
• Create custom rules by running shell scripts and passing their output to the AutoYaST framework. The number of custom rules is limited to five.
NOTE
For more information about rule creation and usage with AutoYaST, refer to
the package's documentation under /usr/share/doc/packages/au​
toyast2/html/index.html, Chapter Rules and Classes.
To prepare for a rule-based AutoYaST mass installation, proceed as follows:
1 Create several AutoYaST profiles that contain the installation details needed for
your heterogeneous setup as described in Section 21.1.1, “Creating an AutoYaST
Profile” (page 344).
2 Define rules to match the system attributes of your hardware setup as shown in
Section 21.2.2, “Example Scenario for Rule-Based Autoinstallation” (page 357).
3 Determine the source of the AutoYaST profile and the parameter to pass to the installation routines as described in Section 21.1.2, “Distributing the Profile and Determining the autoyast Parameter” (page 346).
4 Determine the source of the SUSE Linux Enterprise installation data as described
in Section 21.1.3, “Providing the Installation Data” (page 348).
5 Pass the command line to the installation routines by adding the parameters manually or by creating an info file as described in Section 21.1.5, “Creating the info
File” (page 351).
6 Determine and set up the boot scenario for autoinstallation as described in Section 21.1.4, “Setting Up the Boot Scenario” (page 349).
7 Start the autoinstallation process as described in Section 21.1.6, “Initiating and
Monitoring the Autoinstallation” (page 354).
356
Deployment Guide
21.2.2 Example Scenario for Rule-Based
Autoinstallation
To get a basic understanding of how rules are created, think of the following example,
depicted in Figure 21.2, “AutoYaST Rules” (page 357). One run of AutoYaST installs the following setup:
A Print Server
This machine just needs a minimal installation without a desktop environment
and a limited set of software packages.
Workstations in the Engineering Department
These machines need a desktop environment and a broad set of development software.
Laptops in the Sales Department
These machines need a desktop environment and a limited set of specialized applications, such as office and calendaring software.
Figure 21.2: AutoYaST Rules
Automated Installation
357
In a first step, use one of the methods outlined in Section 21.1.1, “Creating an AutoYaST Profile” (page 344) to create profiles for each use case. In this example, you
would create print.xml, engineering.xml, and sales.xml.
In the second step, create rules to distinguish the three hardware types from one another and to tell AutoYaST which profile to use. Use an algorithm similar to the following to set up the rules:
1. Does the machine have an IP of 192.168.2.253? Then make it the print server.
2. Does the machine have PCMCIA hardware and feature an Intel chipset? Then consider it an Intel laptop and install the sales department software selection.
3. If none of the above is true, consider the machine a developer workstation and install accordingly.
Roughly sketched, this translates into a rules.xml file with the following content:
<?xml version="1.0"?>
<!DOCTYPE autoinstall SYSTEM "/usr/share/autoinstall/dtd/rules.dtd">
<autoinstall xmlns="http://www.suse.com/1.0/yast2ns" xmlns:config="http://
www.suse.com/1.0/configns">
<rules config:type="list">
<rule>
<hostaddress>
<match>192.168.2.253</match>
<match_type>exact</match_type>
</hostaddress>
<result>
<profile>print.xml</profile>
<continue config:type="boolean">false</continue>
</result>
</rule>
<rule>
<haspcmcia>
<match>1</match>
<match_type>exact</match_type>
</haspcmcia>
<custom1>
<script>
if grep -i intel /proc/cpuinfo > /dev/null; then
echo -n "intel"
else
echo -n "non_intel"
fi;
</script>
<match>*</match>
<match_type>exact</match_type>
358
Deployment Guide
</custom1>
<result>
<profile>sales.xml</profile>
<continue config:type="boolean">false</continue>
</result>
<operator>and</operator>
</rule>
<rule>
<haspcmcia>
<match>0</match>
<match_type>exact</match_type>
</haspcmcia>
<result>
<profile>engineering.xml</profile>
<continue config:type="boolean">false</continue>
</result>
</rule>
</rules>
</autoinstall>
When distributing the rules file, make sure that the rules directory resides under
the profiles directory, specified in the autoyast=protocol:serverip/
profiles/ URL. AutoYaST looks for a rules subdirectory containing a file
named rules.xml first then loads and merges the profiles specified in the rules
file.
The rest of the autoinstallation procedure is carried out as usual.
21.3 For More Information
For in-depth information about the AutoYaST technology, refer to AutoYaST (↑AutoYaST) or the documentation installed along with the software (/usr/share/
doc/packages/autoyast2).
Automated Installation
359
Automated Upgrade from
SUSE Linux Enterprise 11
SP2 to 11 SP3
22
The following procedure is a way to do a mass upgrade unattended from SUSE Linux Enterprise 11 SP2 to SUSE Linux Enterprise 11 SP3. Several preparation steps are
needed to create a suitable AutoYaST profile. AutoYaST finally will execute the upgrade process.
22.1 Preparing the AutoYaST
Profile
The AutoYaST profile for the automated upgrade uses the same file format as the
AutoYaST installation. For more information about AutoYaST, see Chapter 21, Automated Installation (page 343) and AutoYaST (↑AutoYaST).
However, for obvious reasons, there are some parts of the system (e.g., partitioning)
that do not make sense to be configured during the upgrade. On the other hand, it is
useful to set upgrade-specific options by means of the AutoYaST profile.
22.1.1 Upgrade
The upgrade options define the behavior of the dependency solver during upgrade:
<upgrade>
<only_installed_packages
config:type="boolean">false</only_installed_packages>
Automated Upgrade from SUSE Linux Enterprise 11 SP2 to 11 SP3
361
<stop_on_solver_conflict
config:type="boolean">true</stop_on_solver_conflict>
</upgrade>
only_installed_packages
Set to true for package-based upgrades (recommended for upgrading to the
next service pack of the same product) or false for pattern-based upgrades
(recommended for an upgrade between versions of a product, e.g. from SLES10
to SLES11).
stop_on_solver_conflict
Defines whether to show the proposal in case of failure to resolve package dependencies interactively (recommended to be set to true, but this could result in an
interactive process, during which the user must to resolve the conflicts manually.
22.1.2 Software Selection
The software selection options define, which components to select or deselect in addition to the results of the resolver:
<software>
<packages config:type="list">
<package>autoyast2-installation</package>
<package>apparmor-profile-editor</package>
</packages>
<patterns config:type="list">
<pattern>base</pattern>
</patterns>
<remove-packages config:type="list"/>
<remove-patterns config:type="list"/>
</software>
It is especially important to set packages or patterns for being selected or deselected
in order to resolve package conflicts and thus to avoid the need for interactive intervention. Once the upgrade is done, the newly created autoupg_updated.xml file
contains these packages and patterns plus those that were selected or deselected for
any other reason.
22.1.3 Backup Before Upgrade
The backup before upgrade options match these features in the upgrade proposal.
<backup>
362
Deployment Guide
<sysconfig config:type="boolean">true</sysconfig>
<modified config:type="boolean">true</modified>
<remove_old config:type="boolean">false</remove_old>
</backup>
sysconfig
defines whether to backup sysconfig before upgrading.
modified
defines whether to backup the modified configuration files before upgrading.
remove_old
defines whether to remove old backups from previous upgrades.
22.2 Running the Automated
Upgrade
To start the automated upgrade, boot the installation media and pass the AutoYaST
profile to it. There are two ways to pass the profile to the system:
• Pass the profile to the kernel command line the same way as for the AutoYaST
installation (use the autoupgrade=1 autoyast=http://host/path/
profile.xml parameter. For System z, this is the only possibility.
• Pass the autoupgrade=1 parameter to the kernel command line. Before you
start the upgrade, copy the profile to /root/autoupg.xml. Then there is no
need for any additional kernel parameter.
The latter approach allows you to have a single installation kernel command line for
even different machines—just copy the appropriate profile into its file system.
As long as you have only one SUSE Linux Enterprise system installed on your machine, there are no package conflicts and you did not set the profile to stop on the upgrade proposal, the complete process will be non-interactive. In case you enter the upgrade proposal, you can modify its settings for the upgrade.
After the upgrade finishes, YaST writes the /root/autoupg-updated.xml
file, which contains the profile with applied software selection changes done in the
proposal. This is especially useful in case of mass upgrades of machines with the same
Automated Upgrade from SUSE Linux Enterprise 11 SP2 to 11 SP3
363
package selection. This way, conflict resolutions from one machine can easily be applied on other machines, which consequently will get these conflicts resolved automatically and the upgrade itself will be non-interactive.
If there are more SUSE Linux Enterprise systems installed on the machine, you will
always be asked, which one to upgrade—there is no way to select it in advance.
22.3 GRUB Menu Section for
Booting into the Upgrade
An alternate way to boot the system is to create an additional section in the GRUB
menu (and similar for other boot loaders and other architectures), which starts the installation. The following example assumes that there is a separate /boot partition,
which is referred in GRUB as (hd0,0):
title Upgrade
root (hd0,0)
kernel /upgrade/linux
install=inst_source_url autoupgrade=1
autoyast=autoyast_profile_url vga=0x314
initrd /upgrade/initrd
The above example assumes that the installation kernel and the installation initrd
are located in the /boot/upgrade directory.
On System z, you must add the parameters to the PARM file—proceed the same way
as you do when performing an AutoYaST-driven installation.
22.4 Second Stage of the Upgrade
The automated upgrade by default does not perform configuration changes during
the second stage of the upgrade. The only exception is network configuration, which
needs to be set to be preserved in the AutoYaST upgrade profile.
If configuration adjustment of some system areas is needed after the upgrade (e.g.,
configuring a new service), add the relevant sections to the AutoYaST profile for the
upgrade and the configuration of the selected system areas will be saved during the
upgrade.
364
Deployment Guide
WARNING: AutoYaST Supplied Configuration Replaces Exisiting
Configuration
Be warned that existing configuration of that system area will be replaced
and thus destroyed by the AutoYaST configuration.
Normally, the only configuration adjustment, which should be present in the AutoYaST profile, is the registration of the system with Subscription Management Tool
(SMT) or Novell Customer Center (NCC). If this is missing, the system will not get
the update repository and updates will not be possible—unless configured later again.
22.5 Limitations and Hints
22.5.1 NetworkManager and Registration
In case of using NetworkManager for managing network devices and network connections, network connection is not available during the second stage of the upgrade. This
prevents the system from performing the registration.
22.5.2 Cleaning Up Upgrade Setting
If you do any changes in your system in order to trigger the upgrade process (e.g.,
adding a new section to the boot loader menu), you probably want to remove it after
the upgrade is done.
You can do it automatically with a post-installation script. Find an examples in
Section “Custom User Scripts” (Chapter 4, Configuration and Installation Options,
↑AutoYaST). A sample script cleaning up GRUB's menu.lst is included in the sample autoupg.xml file. Make sure that the script matches your particular set-up and
that it does not remove more than you actually want!
22.5.3 For More Information
• Linuxrc Documentation: http://en.opensuse.org/SDB:Linuxrc
Automated Upgrade from SUSE Linux Enterprise 11 SP2 to 11 SP3
365
Automated Deployment of
Preload Images
23
With KIWI you are able to create operating system images. This chapter describes the
process of deploying a system image to an empty client machine. For this, you have to
create a preload image which contains a bootable RAW image. This file contains two
important parts: a partition table and the actual operating system. This RAW image
will be written to the empty hard disk and the operating system extends to the remaining disk space at first boot.
To create such an image, see Section 17.4.2, “Creating an Image” (page 318). When
you build the ISO image, you can find the RAW file in the destination folder. There
are many ways to dump a raw image onto a disk.
• Plug the disk into a deployment server and just copy the image to the raw device.
• Provide the raw image by means of a HTTP or FTP server and dump it on the disk
of the client machine.
• Create a netboot image to get the image and dump it on the disk. This is a good
method for mass deployment.
• Boot a rescue disk and do the dump manually from the rescue image.
For a quick start, it is good to use one of the methods described in Section 23.1, “Deploying system manually from rescue image” (page 368).
Automated Deployment of Preload Images
367
23.1 Deploying system manually
from rescue image
Deploying with generated ISO file from KIWI:
1. Burn the ISO image you get from the KIWI building process, see Section 17.4.2, “Creating an Image” (page 318) on CD/DVD
2. Boot from this medium onto the client machine.
3. Select the hard disk for installation.
4. Restart the client machine and boot from hard disk.
Deploying over rescue system:
1. Boot the client machine with a rescue system. Such systems are available on all
SUSE installation CDs or DVDs.
2. Log in as root. Do not enter password.
3. Configure your network. If you have DHCP available in your network, this is
merely the command ifup-dhcp eth0. If you must do this manually, use
the command ip to configure your network. The output starting DHCP also
tells you the IP address of the computer.
4. Listen on an unused port of your network like 1234 and dump the incoming
data to disk with the following command:
netcat -l -p 1234 > /dev/sda
5. On the imaging server, send the raw image to the client machine with the command:
netcat <IP of client> 1234 < $HOME/preload_image/<image_name>
6. When the image is transferred, remove the rescue system from your CD or
DVD drive and shutdown the client machine. On reboot, the boot loader GRUB
should be started on the client and the firstboot system will take over.
368
Deployment Guide
23.2 Automated Deployment with
PXE Boot
When doing mulitple installations of an operating system on similar hardware, it is
useful to put some effort into preparing a mass deployment of the operating system
and to minimize the time needed for the actual deployment. This chapter describes
this process. The goal is to simply plug in a computer, connect it to a network, start a
network boot, and wait until it powers down.
The following actions have to be performed in order to accomplish this task:
Setup a boot and install server
A dedicated machine is needed, that should be prepared to offer PXE boot as
well as an ftp or Web server to provide a preload image. It is a good idea to give
the machine enough memory to hold all necessary installation data in memory.
For a default installation, you should have at least 4 GByte of memory. All the
necessary tasks can be accomplished with SUSE Linux Enterprise Server. For
more details, see Section 23.2.1, “Setup a Boot and Install Server” (page 370).
Prepare a preload Image
The actual installation is done by the copying of a raw image of the operating system to the new hard disk. All features and settings must be prepared and tested
carefully. To provide such an image, KIWI can be used (available in the SDK of
the SUSE Linux Enterprise operating system). More information about image
creation with KIWI is available in Chapter 17, KIWI (page 313). For more details
about the requirements of the preload image, see Section 23.2.2, “Creating a Preload Image” (page 370).
Create an initial system for deployment
This is a task that requires some linux expertise. A description on how this can be
achieved by means of an example installation is available at Section 23.2.3, “Creating a Initial System to Deploy a Preload Image” (page 371).
Configure the boot server for automatic deployment
PXE boot must be told to boot the installation system, that in turn will take the
preload image from the server and copy it to the hard disk.
Automated Deployment of Preload Images
369
23.2.1 Setup a Boot and Install Server
There are four steps to accomplish in order to perform this task after a SUSE Linux
Enterprise Server installation:
1 Set up the installation source as described in Section 14.2, “Setting Up the Server
Holding the Installation Sources” (page 254). Choose an HTTP, or FTP network
server.
2 Set up a TFTP server to hold a boot image (this image will be created in a later
step). This is described in Section 14.3.2, “Setting Up a TFTP Server” (page 265).
3 Set up a DHCP server to assign IP addresses to all machines and to reveal the location of the TFTP server to the target system. This is described in Section 14.3.1,
“Setting Up a DHCP Server” (page 263).
4 Prepare the installation server PXE boot. This is described in further detail in Section 14.3.3, “Using PXE Boot” (page 267).
Note that the actual installation process will greatly benefit if you provide enough
memory on this machine to hold the preload image. Also, using gigabit ethernet will
speedup the deployment process considerably compared to slower networks.
23.2.2 Creating a Preload Image
The process of creating images with KIWI is described in Section 17.4.2, “Creating
an Image” (page 318). However, to create a useful image for mass deployment, several considerations should be taken into account:
• A typical preload image will use the following type:
<type primary="true" filesystem="ext3" boot="oemboot/suse-SLES11">vmx</
type>
• During the setup of a preload image, the image creation process is run multiple
times. The repositories needed to build the image should be available on the local
computer.
• Depending on the desired usage of the preload, some effort should be invested in
configuring firstboot. Find more details about firstboot in Chapter 20, Deploying
370
Deployment Guide
Customized Preinstallations (page 329). With this method you can also require the
user to do initial configurations at the first bootup of the system.
• Many additional features can be configured into the image, like adding update
repositories or doing an update on initial bootup. However, it is impossible to describe all possibilities in this document, and (depending on the requirements) the
creation of the preload image requires in-depth knowledge of the imaging system
KIWI, as well as several other technologies used in SUSE Linux Enterprise Server.
The actual image to be deployed should be available from the ftp or http server that
you provided on the installation server.
23.2.3 Creating a Initial System to Deploy
a Preload Image
In order to run an automatic deployment, it is necessary to start an initial linux system
on the target computer. During a typical installation, the kernel and initial ram file
system are read from some boot medium and started by the bios. The needed functionality can be implemented in the ram file system, which together with the kernel
will serve as the initial system.
The main features that must be provided by the initial system is the enabling of access
to the hard disk and the making available of the network connection. Both of these
functions are dependent on the hardware onto which you want to deploy. In theory it
is possible to create an initial system from scratch, but to ease this task it is also possible to modify the initial ram file system used by the machine during boot.
The following procedure is just one example of how to create the needed initial ram
file system:
1 Do a standard installation of SUSE Linux Enterprise Server on the target system.
2 Install the package busybox on the system.
3 Create a new ram file system with the following command:
mkinitrd -f busybox -D eth0
Note that eth0 represents the ethernet device to which your network cable is attached. The parameter -f busybox adds the multi call binary busybox to
Automated Deployment of Preload Images
371
the ram file system. After doing this, many standard unix commands are available inside this system.
4 Copy the new ram file system and the kernel to your boot server with the command:
scp /boot/initrd /boot/vmlinuz pxe.example.com:
Replace pxe.example.com with the name of your local boot server or ip address.
5 Log into your bootserver as user root, and create a directory where you can
modify the ram file system:
mkdir ~/bootimage
6 Change your working directory to this directory with the command cd ~/
bootimage.
7 Unpack the previously copied initial ram file system with the command:
zcat ../initrd | cpio -i
8 Edit the file run_all.sh.
9 Search for the following line, delete it and the rest of the file:
[ "$debug" ] && echo preping 21-nfs.sh
10 Add the following lines to the end of the files run_all.sh:
[ "$debug" ] && echo preping 92-install.sh
[ "$debug" ] && echo running 92-install.sh
source boot/92-install.sh
[ "$modules" ] && load_modules
11 Create a new script boot/92-install.sh with the following content:
#!/bin/bash
if [ "$(get_param rawimage)" ]; then
rawimage=$(get_param rawimage)
if [ "$(get_param rawdevice)" ]; then
rawdevice=$(get_param rawdevice)
echo "wget -O ${rawdevice} ${rawimage}"
wget -O ${rawdevice} ${rawimage}
sync
sleep 5
echo "DONE"
fi
fi
372
Deployment Guide
# /bin/bash
/bin/poweroff -f
12 If you want to have a debug shell before the computer switches off, remove the
comment sign before /bin/bash.
13 Make this script executable with the command chmod 755 boot/92install.sh.
14 Create a new initial ram file system with the commands:
mkdir -p /srv/tftpboot
find . | cpio --quiet -H newc -o | gzip -9 -n > \
/srv/tftpboot/initrd.boot
15 Copy the kernel to this directory:
cp ../vmlinuz /srv/tftpboot/linux.boot
The initial ram file system is now prepared to take two new kernel command line
parameters. The parameter rawimage=<URL> is used to identify the location of
the preload image. Any URL that is understood by wget can be used. The parameter
rawdevice=<device> is used to identify the block device for the hard disk on
the target machine.
23.2.4 Boot Server Configuration
The configuration of the boot server is covered in detail in several different chapters
as listed in Section 23.2.1, “Setup a Boot and Install Server” (page 370). This section should give a checklist that covers steps that are necessary to configure the system.
• Setup a dhcp server. The subnet where the machines are installed needs the additional lines:
filename "pxelinux.0";
next-server 192.168.1.115;
In this example, 192.168.1.115 is the ip address of the PXE server
pxe.example.com.
• Configure a PXE server as described in Section 14.3.3, “Using PXE
Boot” (page 267). When editing /srv/tftpboot/pxelinux.cfg/de​
fault, add the following entries:
Automated Deployment of Preload Images
373
default bootinstall
label bootinstall
kernel linux.boot
append initrd=initrd.boot \
rawimage=ftp://192.168.1.115/preload/preloadimage.raw rawdevice=/dev/sda
• Setup an ftp server and copy your prepared preload image to /srv/ftp/pre​
load/preloadimage.raw.
Test your setup by booting the target system with PXE network boot. This will automatically copy the prepared preload image to hard disk and switch off the machine
when ready.
374
Deployment Guide
GNU Licenses
This appendix contains the GNU Free Documentation License version 1.2.
GNU Free Documentation License
Copyright (C) 2000, 2001, 2002 Free Software Foundation, Inc. 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA. Everyone is permitted to
copy and distribute verbatim copies of this license document, but changing it is not allowed.
0. PREAMBLE
The purpose of this License is to make a manual, textbook, or other functional and useful document "free" in the sense of freedom: to assure everyone
the effective freedom to copy and redistribute it, with or without modifying it, either commercially or noncommercially. Secondarily, this License preserves for the author and publisher a way to get credit for their work, while not being considered responsible for modifications made by others.
This License is a kind of "copyleft", which means that derivative works of the document must themselves be free in the same sense. It complements
the GNU General Public License, which is a copyleft license designed for free software.
We have designed this License in order to use it for manuals for free software, because free software needs free documentation: a free program should
come with manuals providing the same freedoms that the software does. But this License is not limited to software manuals; it can be used for any textual work, regardless of subject matter or whether it is published as a printed book. We recommend this License principally for works whose purpose
is instruction or reference.
1. APPLICABILITY AND DEFINITIONS
This License applies to any manual or other work, in any medium, that contains a notice placed by the copyright holder saying it can be distributed under the terms of this License. Such a notice grants a world-wide, royalty-free license, unlimited in duration, to use that work under the conditions stated herein. The "Document", below, refers to any such manual or work. Any member of the public is a licensee, and is addressed as "you". You accept
the license if you copy, modify or distribute the work in a way requiring permission under copyright law.
A "Modified Version" of the Document means any work containing the Document or a portion of it, either copied verbatim, or with modifications
and/or translated into another language.
A "Secondary Section" is a named appendix or a front-matter section of the Document that deals exclusively with the relationship of the publishers or
authors of the Document to the Document's overall subject (or to related matters) and contains nothing that could fall directly within that overall subject. (Thus, if the Document is in part a textbook of mathematics, a Secondary Section may not explain any mathematics.) The relationship could be
a matter of historical connection with the subject or with related matters, or of legal, commercial, philosophical, ethical or political position regarding
them.
The "Invariant Sections" are certain Secondary Sections whose titles are designated, as being those of Invariant Sections, in the notice that says that the
Document is released under this License. If a section does not fit the above definition of Secondary then it is not allowed to be designated as Invariant.
The Document may contain zero Invariant Sections. If the Document does not identify any Invariant Sections then there are none.
A
The "Cover Texts" are certain short passages of text that are listed, as Front-Cover Texts or Back-Cover Texts, in the notice that says that the Document is released under this License. A Front-Cover Text may be at most 5 words, and a Back-Cover Text may be at most 25 words.
A "Transparent" copy of the Document means a machine-readable copy, represented in a format whose specification is available to the general public, that is suitable for revising the document straightforwardly with generic text editors or (for images composed of pixels) generic paint programs or
(for drawings) some widely available drawing editor, and that is suitable for input to text formatters or for automatic translation to a variety of formats
suitable for input to text formatters. A copy made in an otherwise Transparent file format whose markup, or absence of markup, has been arranged to
thwart or discourage subsequent modification by readers is not Transparent. An image format is not Transparent if used for any substantial amount of
text. A copy that is not "Transparent" is called "Opaque".
Examples of suitable formats for Transparent copies include plain ASCII without markup, Texinfo input format, LaTeX input format, SGML or XML
using a publicly available DTD, and standard-conforming simple HTML, PostScript or PDF designed for human modification. Examples of transparent image formats include PNG, XCF and JPG. Opaque formats include proprietary formats that can be read and edited only by proprietary word
processors, SGML or XML for which the DTD and/or processing tools are not generally available, and the machine-generated HTML, PostScript or
PDF produced by some word processors for output purposes only.
The "Title Page" means, for a printed book, the title page itself, plus such following pages as are needed to hold, legibly, the material this License requires to appear in the title page. For works in formats which do not have any title page as such, "Title Page" means the text near the most prominent
appearance of the work's title, preceding the beginning of the body of the text.
A section "Entitled XYZ" means a named subunit of the Document whose title either is precisely XYZ or contains XYZ in parentheses following text
that translates XYZ in another language. (Here XYZ stands for a specific section name mentioned below, such as "Acknowledgements", "Dedications",
"Endorsements", or "History".) To "Preserve the Title" of such a section when you modify the Document means that it remains a section "Entitled
XYZ" according to this definition.
The Document may include Warranty Disclaimers next to the notice which states that this License applies to the Document. These Warranty Disclaimers are considered to be included by reference in this License, but only as regards disclaiming warranties: any other implication that these Warranty Disclaimers may have is void and has no effect on the meaning of this License.
2. VERBATIM COPYING
You may copy and distribute the Document in any medium, either commercially or noncommercially, provided that this License, the copyright notices, and the license notice saying this License applies to the Document are reproduced in all copies, and that you add no other conditions whatsoever
to those of this License. You may not use technical measures to obstruct or control the reading or further copying of the copies you make or distribute.
However, you may accept compensation in exchange for copies. If you distribute a large enough number of copies you must also follow the conditions
in section 3.
You may also lend copies, under the same conditions stated above, and you may publicly display copies.
3. COPYING IN QUANTITY
If you publish printed copies (or copies in media that commonly have printed covers) of the Document, numbering more than 100, and the Document's
license notice requires Cover Texts, you must enclose the copies in covers that carry, clearly and legibly, all these Cover Texts: Front-Cover Texts on
the front cover, and Back-Cover Texts on the back cover. Both covers must also clearly and legibly identify you as the publisher of these copies. The
front cover must present the full title with all words of the title equally prominent and visible. You may add other material on the covers in addition.
Copying with changes limited to the covers, as long as they preserve the title of the Document and satisfy these conditions, can be treated as verbatim
copying in other respects.
If the required texts for either cover are too voluminous to fit legibly, you should put the first ones listed (as many as fit reasonably) on the actual cover, and continue the rest onto adjacent pages.
If you publish or distribute Opaque copies of the Document numbering more than 100, you must either include a machine-readable Transparent copy
along with each Opaque copy, or state in or with each Opaque copy a computer-network location from which the general network-using public has access to download using public-standard network protocols a complete Transparent copy of the Document, free of added material. If you use the latter
option, you must take reasonably prudent steps, when you begin distribution of Opaque copies in quantity, to ensure that this Transparent copy will remain thus accessible at the stated location until at least one year after the last time you distribute an Opaque copy (directly or through your agents or
retailers) of that edition to the public.
It is requested, but not required, that you contact the authors of the Document well before redistributing any large number of copies, to give them a
chance to provide you with an updated version of the Document.
4. MODIFICATIONS
You may copy and distribute a Modified Version of the Document under the conditions of sections 2 and 3 above, provided that you release the Modified Version under precisely this License, with the Modified Version filling the role of the Document, thus licensing distribution and modification of
the Modified Version to whoever possesses a copy of it. In addition, you must do these things in the Modified Version:
376
Deployment Guide
A.Use in the Title Page (and on the covers, if any) a title distinct from that of the Document, and from those of previous versions (which should, if
there were any, be listed in the History section of the Document). You may use the same title as a previous version if the original publisher of that
version gives permission.
B. List on the Title Page, as authors, one or more persons or entities responsible for authorship of the modifications in the Modified Version, together
with at least five of the principal authors of the Document (all of its principal authors, if it has fewer than five), unless they release you from this
requirement.
C.State on the Title page the name of the publisher of the Modified Version, as the publisher.
D.Preserve all the copyright notices of the Document.
E. Add an appropriate copyright notice for your modifications adjacent to the other copyright notices.
F. Include, immediately after the copyright notices, a license notice giving the public permission to use the Modified Version under the terms of this
License, in the form shown in the Addendum below.
G.Preserve in that license notice the full lists of Invariant Sections and required Cover Texts given in the Document's license notice.
H.Include an unaltered copy of this License.
I. Preserve the section Entitled "History", Preserve its Title, and add to it an item stating at least the title, year, new authors, and publisher of the Modified Version as given on the Title Page. If there is no section Entitled "History" in the Document, create one stating the title, year, authors, and publisher of the Document as given on its Title Page, then add an item describing the Modified Version as stated in the previous sentence.
J. Preserve the network location, if any, given in the Document for public access to a Transparent copy of the Document, and likewise the network locations given in the Document for previous versions it was based on. These may be placed in the "History" section. You may omit a network location for a work that was published at least four years before the Document itself, or if the original publisher of the version it refers to gives permission.
K.For any section Entitled "Acknowledgements" or "Dedications", Preserve the Title of the section, and preserve in the section all the substance and
tone of each of the contributor acknowledgements and/or dedications given therein.
L. Preserve all the Invariant Sections of the Document, unaltered in their text and in their titles. Section numbers or the equivalent are not considered
part of the section titles.
M.Delete any section Entitled "Endorsements". Such a section may not be included in the Modified Version.
N.Do not retitle any existing section to be Entitled "Endorsements" or to conflict in title with any Invariant Section.
O.Preserve any Warranty Disclaimers.
If the Modified Version includes new front-matter sections or appendices that qualify as Secondary Sections and contain no material copied from the
Document, you may at your option designate some or all of these sections as invariant. To do this, add their titles to the list of Invariant Sections in the
Modified Version's license notice. These titles must be distinct from any other section titles.
You may add a section Entitled "Endorsements", provided it contains nothing but endorsements of your Modified Version by various parties--for example, statements of peer review or that the text has been approved by an organization as the authoritative definition of a standard.
You may add a passage of up to five words as a Front-Cover Text, and a passage of up to 25 words as a Back-Cover Text, to the end of the list of Cover Texts in the Modified Version. Only one passage of Front-Cover Text and one of Back-Cover Text may be added by (or through arrangements
made by) any one entity. If the Document already includes a cover text for the same cover, previously added by you or by arrangement made by the
same entity you are acting on behalf of, you may not add another; but you may replace the old one, on explicit permission from the previous publisher
that added the old one.
The author(s) and publisher(s) of the Document do not by this License give permission to use their names for publicity for or to assert or imply endorsement of any Modified Version.
5. COMBINING DOCUMENTS
You may combine the Document with other documents released under this License, under the terms defined in section 4 above for modified versions,
provided that you include in the combination all of the Invariant Sections of all of the original documents, unmodified, and list them all as Invariant
Sections of your combined work in its license notice, and that you preserve all their Warranty Disclaimers.
The combined work need only contain one copy of this License, and multiple identical Invariant Sections may be replaced with a single copy. If there
are multiple Invariant Sections with the same name but different contents, make the title of each such section unique by adding at the end of it, in
parentheses, the name of the original author or publisher of that section if known, or else a unique number. Make the same adjustment to the section
titles in the list of Invariant Sections in the license notice of the combined work.
In the combination, you must combine any sections Entitled "History" in the various original documents, forming one section Entitled "History"; likewise combine any sections Entitled "Acknowledgements", and any sections Entitled "Dedications". You must delete all sections Entitled "Endorsements".
GNU Licenses
377
6. COLLECTIONS OF DOCUMENTS
You may make a collection consisting of the Document and other documents released under this License, and replace the individual copies of this License in the various documents with a single copy that is included in the collection, provided that you follow the rules of this License for verbatim
copying of each of the documents in all other respects.
You may extract a single document from such a collection, and distribute it individually under this License, provided you insert a copy of this License
into the extracted document, and follow this License in all other respects regarding verbatim copying of that document.
7. AGGREGATION WITH INDEPENDENT WORKS
A compilation of the Document or its derivatives with other separate and independent documents or works, in or on a volume of a storage or distribution medium, is called an "aggregate" if the copyright resulting from the compilation is not used to limit the legal rights of the compilation's users beyond what the individual works permit. When the Document is included in an aggregate, this License does not apply to the other works in the aggregate which are not themselves derivative works of the Document.
If the Cover Text requirement of section 3 is applicable to these copies of the Document, then if the Document is less than one half of the entire aggregate, the Document's Cover Texts may be placed on covers that bracket the Document within the aggregate, or the electronic equivalent of covers if
the Document is in electronic form. Otherwise they must appear on printed covers that bracket the whole aggregate.
8. TRANSLATION
Translation is considered a kind of modification, so you may distribute translations of the Document under the terms of section 4. Replacing Invariant
Sections with translations requires special permission from their copyright holders, but you may include translations of some or all Invariant Sections
in addition to the original versions of these Invariant Sections. You may include a translation of this License, and all the license notices in the Document, and any Warranty Disclaimers, provided that you also include the original English version of this License and the original versions of those notices and disclaimers. In case of a disagreement between the translation and the original version of this License or a notice or disclaimer, the original
version will prevail.
If a section in the Document is Entitled "Acknowledgements", "Dedications", or "History", the requirement (section 4) to Preserve its Title (section 1)
will typically require changing the actual title.
9. TERMINATION
You may not copy, modify, sublicense, or distribute the Document except as expressly provided for under this License. Any other attempt to copy,
modify, sublicense or distribute the Document is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
10. FUTURE REVISIONS OF THIS LICENSE
The Free Software Foundation may publish new, revised versions of the GNU Free Documentation License from time to time. Such new versions will
be similar in spirit to the present version, but may differ in detail to address new problems or concerns. See http://www.gnu.org/copyleft/.
Each version of the License is given a distinguishing version number. If the Document specifies that a particular numbered version of this License "or
any later version" applies to it, you have the option of following the terms and conditions either of that specified version or of any later version that has
been published (not as a draft) by the Free Software Foundation. If the Document does not specify a version number of this License, you may choose
any version ever published (not as a draft) by the Free Software Foundation.
ADDENDUM: How to use this License for your documents
Copyright (c) YEAR YOUR NAME.
Permission is granted to copy, distribute and/or modify this document
under the terms of the GNU Free Documentation License, Version 1.2
or any later version published by the Free Software Foundation;
with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts.
A copy of the license is included in the section entitled “GNU
Free Documentation License”.
If you have Invariant Sections, Front-Cover Texts and Back-Cover Texts, replace the “with...Texts.” line with this:
378
Deployment Guide
with the Invariant Sections being LIST THEIR TITLES, with the
Front-Cover Texts being LIST, and with the Back-Cover Texts being LIST.
If you have Invariant Sections without Cover Texts, or some other combination of the three, merge those two alternatives to suit the situation.
If your document contains nontrivial examples of program code, we recommend releasing these examples in parallel under your choice of free software license, such as the GNU General Public License, to permit their use in free software.
GNU Licenses
379
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement