null  null
KLU Series
Universal Weighbars
Operator’s Manual
127469 Rev B
Contents
1.0
Introduction.................................................................................................................................. 1
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.0
3.0
4.0
5.0
Technical Specifications ............................................................................................................. 2
Installation ................................................................................................................................... 3
Parts List ...................................................................................................................................... 4
Maintenance ................................................................................................................................ 8
5.1 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.0
Troubleshooting ......................................................................................................................... 10
6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.2 Drifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.3 Abnormally Large Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
KLU Series Limited Warranty................................................................................................................. 14
For More Information ............................................................................................................................. 15
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
© Rice Lake Weighing Systems. All rights reserved. Printed in the United States of America.
Specifications subject to change without notice.
Rice Lake Weighing Systems is an ISO 9001 registered company.
August 27, 2013
Rice Lake continually offers web-based video training on a growing selection
of product-related topics at no cost. Visit www.ricelake.com/webinars.
ii
KLU Series Operator’s Manual
1.0
Introduction
The electronic weighing equipment you have purchased has been manufactured using high quality components and
the latest production techniques to ensure reliable, trouble-free operation for years to come. To obtain the best
possible performance from your weighing equipment, please read this manual carefully.
The load bar consists of a steel tube containing load cell mounts, load cells, and mounting pads. Each bar contains
two factory calibrated load cells. The load bars are of solid construction and, therefore, do not require any
horizontal checking (check rods). Load bars are designed to withstand horizontal loads in the same range as their
capacity without any damage. Care should be taken to remove the possibility of horizontal impacts with the scale
platform. Impacts or collisions tend to create very high forces.
The versatility of the load bars allows any platform or container to become a weigh scale by placing a set of bars
beneath them. Various indicator combinations can be matched to the load bars to meet specialized applications.
1.1 Safety
Safety Symbol Definitions:
Indicates a potentially hazardous situation that, if not avoided could result in serious injury or death, and
WARNING includes hazards that are exposed when guards are removed.
Indicates information about procedures that, if not observed, could result in damage to equipment or
Important corruption to and loss of data.
General Safety
Do not operate or work on this equipment unless you have read and understand the instructions and
warnings in this manual. Failure to follow the instructions or heed the warnings could result in injury or
death. Contact any Rice Lake Weighing Systems dealer for replacement manuals. Proper care is your
responsibility.
WARNING
Failure to heed may result in serious injury of death.
DO NOT allow minors (children) or inexperienced persons to operate this unit.
DO NOT operate without all shields and guards in place.
DO NOT jump on the scale.
DO NOT use for purposes other than weight taking.
DO NOT place fingers into slots or possible pinch points.
DO NOT use any load bearing component that is worn beyond 5% of the original dimension.
DO NOT use this product if any of the components are cracked.
DO NOT exceed the rated load limit of the unit.
DO NOT make alterations or modifications to the unit.
DO NOT remove or obscure warning labels.
Keep hands, feet and loose clothing away from moving parts.
Introduction
1
2.0
Technical Specifications
For all KLU Series Load Bars
Nominal Output
2.5 mV/V *
Max. Excitation Voltage
+15V D.C.
Thermal Shift
0.0012% FS/°F
Thermal Sensitivity Shift
0.0008% of Reading/°F
Hysterisis
0.02% FS
Non Linearity
0.02% FS
Operating Temp. range
-40 to 105°F (-40 to 40°C)
Overload Capacity
150% of Rated Capacity
Side Discrimination
1000:1
Bridge Resistance
350 Ohms
* Output is standardized for each load bar. Contact factory for details.
Table 2-1. Specifications
SLOTTED HOLE 7/16" x 1 1/4"
MODELS 1-5 KLU
1 KLU
2 KLU
4 KLU
G
F C W
G
E
C F
B
HOLE FOR LEVELING SCREWS
(1/2" N.C.) 8,16,30,45,60 KLU
A
1" Ø MOUNTING HOLES (8 & 16 KLU)
1.25" Ø MOUNTING HOLES (30,45,60 KLU)
E
LOAD CELL CABLE
(20' LONG)
L
2" x 2" x 1/4" ANGLE
2" WIDE - 2 KLU
1.5" x 1.5" x 1/8" ANGLE
1.5" WIDE - .1-1 KLU
H
K
P
D
N
H(a)
5" Ø PAD - .1-5,1,2,4 KLU
7" Ø PAD - 8,16 KLU
KLU
Model
Capacity
(lb)
A
B
*.1,.2,.3
100 to 300
15
500 to 1000 15
*0.5,1
E
F
G
H
H(a)
Portable Bar
K
L
N
P
W
5
4 1/4 L-2 1/4 6
6
3
3 7/8
4 1/4 - 4 3/4
7/8
22
L+3 3/4
---
3
5
4 1/4 L-1 3/4 6
6
3
3 7/8
4 1/4 - 4 3/4
7/8
22
L+4 1/4
---
3
4
4 1/2 - 5
1
27-48
L+3 3/4
(L/2)-12 1/2
3
C
D
2
2000
L-12 5
4 1/8 L-2 1/4 6
6
3
4
4000
L-12 5
4 1/4 L-2 1/2 6
6
3
4
4 1/2 - 5
1
28-72
L+3 1/2
(L/2)-12 1/2
3
8
8000
L-12 6
4 1/2 L-3 1/4 8
6
1
5 1/4
6 - 6 1/2
1 1/4
30-96
L+4 3/4
(L/2)-13 3/8
4
16
16000
L-12 6
4 1/2 L-2 3/4 8
6
1
5 1/4
6 - 6 1/2
1 1/4
30-96
L+5 1/4
(L/2)-13 3/8
4
30
30000
L-12 7
---
1 15/16 34-120 L+5 1/2
(L/2)-15 1/4
5
---
1 15/16 34-120 L+5 1/2
45
45000
L-12 7
60
60000
L-12 8
60KLUR
60000
10
8
60KLUP
60000
10
8
8
L-4 1/2 8
10
1 6 15/16
8
L-4 1/2 8
10
1 6 15/16
(L/2)-15 1/4
5
---
1 7/8
44-120 L+5 1/2
(L/2)-20 1/4
6
7 7/8
---
1 7/8
44-120 L+6 1/2
(L/2)-20 1/4
6
---
7 7/8
1 7/8
44-120
(L/2)-20 1/4
6
8 1/2 L-5 1/2 12 11 1/2 1
7 7/8
8 1/2 L-5 1/2 12 11 1/2 1
---
L-5 1/2 6
8
--
*These Load Bars available in only 22” lengths.
All measurement are in inches.
Table 2-2. Dimensions
2
KLU Series Universal Weighbars Operator’s Manual
L+3/4
3.0
Installation
The following points are to help ensure proper installation of the load bars. If any further assistance is required,
please contact your nearest factory or dealer.
When planning an outdoor location for the load bars, choose a site which will allow for adequate
Important drainage away from the scale. Immersing the load cells in water can damage the load cells and void the
warranty.
•
•
•
•
•
Try to install the load bars on a firm, level surface. The load bars do not have to be installed perfectly
level, but a substantial slope will decrease accuracy. All weight transfer must take place through the
pads at the end of each load bar. Make sure there is no contact between the ground and the center of the
load bar.
Install the load bars in the upright position. This will allow for accurate weighing and will help keep
any foreign material out of the load bar.
Do not drill into or weld onto the load bars as this may cause internal structural or electrical damage.
Secure the load bars to the weighing platform using the mounting lugs supplied.
Install the cable so that it is not stepped on or run over. Cable failure due to physical damage is not
covered under warranty.
When constructing the weighing platform, ensure excessive sagging does not occur. This may cause
inaccuracies in weighing and could damage the cable.
Figure 3-1. KLU Series Universal Weighbars
Installation
3
4.0
Parts List
100107
Portable
Pad Upright
Load Bar
Tube
Jam Nut
Portable Pad
Bearing Collar
Bearing
Snap Ring
Spacer
Foam Seal
for .X
100547
Load Cell
2
16 KLU
Bolt for
Load Cell
100963
4KLU
Load Cell
.1 1 KLU
Washer
54243
100609
for 8, 16KLU
Set Screws
Load Pin
8, 16 KLU Pads Only
Pad
Figure 4-1. For 0.1 - 16 KLU Load Bar Parts
4
KLU Series Universal Weighbars Operator’s Manual
Items may not be exactly
as shown
Description
Bearing
0.x KLU
1 KLU
2 KLU
4 KLU
8 KLU
16 KLU
Part #
Part #
Part #
Part #
Part #
Part #
101211
1012114
101212
101212
101216
101216
Bearing Collar
54203
54203
55203
56203
63203
63203
*Bearing Collar Assembly
54202
54202
55202
56202
63202
63202
Cotter Pin (5/32” x 1”)
100963
100963
100963
100963
100963
100963
Foam Seal
101232
101232
101232
101233
101234
101234
Hex Mounting Bolt
100735
100735
100735
100735
100718
100718
**Load Bar Tube
59206
59206
61206
62206
63206
64206
Load Cell
60201.X
60201
61201
62201
63201
64201
Load Cell Assm. (Incl. 202)
60200.X
60200
61200
62200
63200
64200
Load Pin
54209
54209
54209
54209
63209
63209
Load Pin Lock Bolt
-----
-----
-----
-----
100609
100609
Load Pin Spacer
54210
54210
54210
56210
63210
63210
Pad
54207
54207
54207
54207
63207
63207
Pad Base Plate
54207P-2
54207P-2
54207P-2
54207P-2
63207P-2
63207P-2
***Pad Portable Upright
54207PX
54207PX
54207PX
54207PX
63207PX
63207PX
Rodent Guard
54243
54243
-----
-----
-----
-----
Set Screw
100802
100802
100802
100802
100806
100806
Snap Button Cover
101008
101008
-----
-----
-----
-----
Snap Ring
101226
101226
101226
101227
101231
101231
Stop Tube
100107
100107
100107
100107
100107
100107
Washer
100931
100931
100931
100931
100938
100938
Operators Manual
127469
127469
127469
127469
127469
127469
*Assembly includes: collar, bearing, snap ring, seals, set screws
**0.1 -> 1 KLU load bars available only in 22" lengths, specify length for others
***Portable Pad 54207PA(clockwise), 54207PB(counter clockwise) direction is determined by look down from top of load bar
and determining direction the stop rod is pointing.
Specify load bar length in inches
Table 4-1. 0.1 - 16 KLU Load Bar Parts
Parts List
5
67207R-2
Upper Pad
Removable
60 KLU Only
67207R-3
Lower Pad
Removable
60 KLU Only
Load Bar
Tube
Portable Pad
Bearing Collar
Bearing
Snap Ring
Spacer
100547
Foam Seal
Bolt for
Load Cell
Load Cell
67214
Set Screws
100593
Load Pin
Pad Permanent
Figure 4-2. For 30, 45, 60 KLU Load Bars
6
KLU Series Universal Weighbars Operator’s Manual
Description
Bearing
30 KLU
45 KLU
60 KLU
Part #
Part #
Part #
101214
128760
101214
128760
101217
127241
127837
Bearing Collar
65203
66203
127834
67203
*Bearing Collar Assembly1
65202
66202
127833
67202
Foam Bearing Seal
101235
126824
101235
126824
101236
126825
Hex Mounting Bolt (Gr. 8)
100700
126999
100700
126999
100700
126999
127146
100547
127146
100547
127146
Liquid-Tite Connector (3/8)
100547
Load Bar Tube (Specify Length)
65206
66206
67206
Load Cell
65201
66201
67201
Load Cell Assembly (Incl. 202)
65200
127824
127829
66200
127831
67200
127836
65209
127829
67209
127848
67209R
127849
Load Pin
65209
Load Pin (Removable Pad)
-----
Load Pin Lock Bolt
100593
127010
100593
127010
100593
127010
Load Pin Spacer
65210
127830
65210
127830
67210
127850
Load Pin Spacer (Removable Pad)
-----
67210R
127851
Load Pin Stop
67214
127852
67214
127852
67214
127852
Pad – Permanent
65207
127826
65207
127826
65207
127826
Pad – Portable
-----
65207P
127828
67207P
127845
Pad – Removable
-----
67207R
127846
Setscrew
100807
126985
100807
126985
100814
126986
Snap Ring
101229
126808
101229
126808
101230
126809
Operators Manual
-----
-----
-----
127469
127469
127469
*Assembly includes: collar, bearing, snap ring, seals and set screws.
Table 4-2. For 30, 45, 60 KLU Load Bars
Parts List
7
5.0
Maintenance
The most common type of problem that can occur is the load is not supported completely by the load bar pads. On
a regular basis check around and under the weigh apparatus to see if any debris has collected near the scale. Any
ice, dirt, mud or manure that builds up around the weigh apparatus can cause inaccurate readings. The scale should
be kept clean to ensure proper operation.
It should also be noted that an excess of debris on top of the scale could also cause problems. Depending on the
type of scale you have, there may be a limited range of weight you can “zero” off the scale. Always keep the buildup of material on top of the scale to a minimum.
Lubrication of the bearings in your scale is also important. The bearings are located in the bearing collar, as shown
in the parts list diagrams in Figure 4-1 and Figure 4-2. Inject grease into the bearings using a syringe at least once
every two years. Use good high-pressure grease to lubricate the bearings completely. Do not use an excess of
grease – it should lubricate the bearing without bleeding around the foam seal.
5.1
Calibration
All Load cells are calibrated at the factory to reduce installation errors. Over the course of time, however, the load
cells may drift out of calibration slightly. Normally when a scale's load cells go out of calibration, the digital
indicator is adjusted to compensate for this.
The KLU Series Loadbars can be calibrated using the front panel, EDP commands, or the Revolution ®
configuration utility. Each method consists of the following steps:
• Zero calibration
• Entering the test weight value
• Span calibration
• Optional rezero calibration for test weights using hooks or chains.
The following sections describe the calibration procedure for each of the calibration methods.
CONFIG
XXXXXXX
FORMAT
CALIBR
WZERO
WVAL
*CAL*
Display and edit
test weight value
Display and edit
zero calibration
A/D count value
SERIAL
PROGRM
WSPAN
XXXXXXX
PFORMT
VERS
REZERO
*CAL*
*CAL*
Display and edit
span calibration
A/D count value
Press Enter to
remove offset from
zero and span
calibrations
Figure 5-1. Calibration (CALIBR) Menu
Front Panel Calibration
To calibrate the indicator using the front panel, do the following:
1. Place the indicator in setup mode (display reads CONFIG) and remove all weight from the scale platform.
If your test weights require hooks or chains, place the hooks or chains on the scale for zero calibration.
2. Press until the display reads CALIBR (see Figure 5-1). Press to go to zero calibration (WZERO).
to calibrate zero. The indicator displays *CAL* while calibration is in
3. With WZERO displayed, press
progress. When complete, the A/D count for the zero calibration is displayed. Press
again to save the
zero calibration value and go to the next prompt (WVAL).
to show the test weight value. Use the
4. With WVAL displayed, place test weights on the scale and press
numeric keypad to enter the actual test weight, then press
to save the value and go to span calibration
(WSPAN).
to calibrate span. The indicator displays *CAL* while calibration is in
5. With WSPAN displayed, press
again to save the
progress. When complete, the A/D count for the span calibration is displayed. Press
span calibration value and go to the next prompt (REZERO).
6. The rezero function is used to remove a calibration offset when hooks or chains are used to hang the test
weights.
• If no other apparatus was used to hang the test weights during calibration, remove the test weights and
press to return to the CALIBR menu.
8
KLU Series Universal Weighbars Operator’s Manual
•
If hooks or chains were used during calibration, remove these and the test weights from the scale. With
all weight removed, press
to rezero the scale. This function adjusts the zero and span calibration
values. The indicator displays *CAL* while the zero and span calibrations are adjusted. When
to enter the value, then
complete, the adjusted A/D count for the zero calibration is displayed. Press
press to return to the CALIBR menu.
7. Press until the display reads CONFIG, then press to exit setup mode.
Note
To perform the calibration using EDP commands or Revolution®, consult the indicator operator's manual.
Maintenance
9
6.0
6.1
Troubleshooting
General
If you are having trouble with your load bars, a few simple procedures should help you determine where the
problem lies. First, inspect the scale for any physical damage. Take special note of the cable and connectors.
Wiggle the cables and connectors while watching the indicator display. If the readout jumps while moving a cable
or connector, there is likely a short or loose connection. Repair or replace the cable or connector as appropriate.
6.2
Drifting
If the scale readout is drifting, moisture may be present somewhere in the scale's electrical circuit. Check for
moisture in any of the connectors, junction boxes, or load bars. Dry any location where you suspect moisture is
present. If you find a location where moisture is collecting on a regular basis, seal the location with a waterproof
sealant.
6.3
Abnormally Large Reading
If the indicator shows a very large number and the readout cannot be changed using the indicators zero adjustment,
there may be a problem in the circuit. To locate this type of problem, a series of electrical resistance measurements
must be made. To perform these checks, you will need an accurate ohmmeter and a soldering iron.
To locate a faulty component with the ohmmeter, start by taking readings in the connector that plugs into the
indicator cable (this is the cable the runs into your scale). The connector has four pins labelled A, B, C and D, the
following chart lists the appropriate resistance readings. Remember, when making this type of measurement the
power must be OFF. Further, be careful that your fingers are not making contact with the probes on the ohmmeter
– if they are, the reading you take may be incorrect.
*Wire Color
Connector Pin
2-Load Bar
System
**One Load Bar
***Single Load
Cell
White – Red
D–C
145Ω
290Ω
395Ω
White-Green
D–B
175Ω
350Ω
350Ω
White-Black
D–A
145Ω
290Ω
395Ω
Black-Green
A–B
145Ω
290Ω
45Ω
Black-Red
A–C
197.5Ω
395Ω
790Ω
Green-Red
B–C
145Ω
290Ω
745Ω
White-Brown
350Ω
Brown-Red
45Ω
>10MΩ
Black-GND
GND-Frame
0
*See Figure 6-1
**Valid only if Loadbar is disconnected from rest of circuit.
***Valid only if Load Cell is disconnected from rest of circuit.
>10MΩ
>10MΩ
0
0
Table 6-1. Ohmmeter Readings
Note This chart is only valid at a temperature of 22°C. Resistance will vary slightly with temperature.
The readings in Table 6-1 should be within 5 ohms of the value shown. The readings are slightly temperature
dependent and as a result will not match Table 6-1 exactly. However, all the readings you take should differ from
the table by the same percentage. For example, if the resistance across pins D & C reads 142Ω ±1Ω, resistance
across pins D & A should also read 142Ω ±1Ω. In other words the values equal in Table 6-1 should also be equal
when you take your measurements. If the readings correspond to the values in the table an electrical problem in the
scale is not likely. If any readings across pins of the connector differ from the chart, each load cell must be checked
individually.
10
KLU Series Universal Weighbars Operator’s Manual
To check a load bar separately, it must be completely disconnected from the scale's electrical circuit. This is
accomplished by disconnecting the load bar at the scale's junction box, Figure 6-1. However if the junction box
contains a Weights & Measures seal, consult your scale dealer before proceeding. To disconnect a load bar, loosen
the screws on the circuit board for the load bar in question, and remove the wires. Resistance measurements can
now be taken as shown in Table 6-1, and should correspond with the values in the "One Load Bar" column in the
same way as described above. If not, consult your scale dealer. The dealer may ask you to check the individual load
cells.
Black (-EX)
Wire from Green (+SIG)
Load Bar 1
Red (+EX)
White (-SIG)
Shield
Black (-EX)
Green (+SIG)
Red (+EX)
White (-SIG)
Shield
Black (-EX)
Green (+SIG) Wire from
Red (+EX)
Load Bar 2
White (-SIG)
Shield
Wire to Instrument
Figure 6-1. Junction Box Wire
When checking an individual load cell, it must be completely disconnected from the scale's electrical circuit. To
accomplish this, the wires will need to be taken apart at the load bar cable splice. See Figure 6-2 for the wiring of a
load bar system. The circuit diagram for the Load Cells of a single load bar is shown in Figure 6-4. Remember that
each load cell contains five wires, but each load bar has only four wires running to the junction box. All five wires
must be disconnected to separate that load cell from the circuit.
Troubleshooting
11
Color Key
Color
Code
Black
BK
Brown
BR
Green
G
Red
R
White
W
Top View
Load Bar 1
BR
G
G
BK
BR
W
BK
Sealed Splice
(Solder, MCOAT-A, Silicone, Heat Shrink)
R
W
R
R (+EX)
W
(-SIG)
BK
(-EX)
G (+SIG)
Junction Box
To Junction Box
to Junction Box
BK
(-EX)
G (+SIG)
R (+EX)
W
(-SIG)
To Instrument
Sealed Splice
(Solder, MCOAT-A, Silicone, Heat Shrink)
R
WH
R
Black
BK
W
G
BR
BR
G
Top View
Load Bar 2
Figure 6-2. Load Bar System Wiring Diagram
D
Indicator
Connector
A
A
B
C
D
C
-EXC
+SIG
+EXC
-SIG
B
Black
Green
Red
White
A
B
Figure 6-3. Load Bar System Connection
12
KLU Series Universal Weighbars Operator’s Manual
KLU Bar
D
C
Red
Loadbar
T = Tension
C = Compression
Red
Black
Tc
Tc
Brown
Green
T
C
White
White
C
Green
T
Green
Brown
Black
Red
Tc
Tc
Load Cell
Load Cell
Black
Figure 6-4. Load Bar Schematic
Troubleshooting
13
KLU Series Limited Warranty
Rice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by a
Distributor or Original Equipment Manufacturer (OEM) will operate per written specifications as confirmed by the
Distributor/OEM and accepted by RLWS. All systems and components are warranted against defects in materials
and workmanship for two years.
RLWS warrants that the equipment sold hereunder will conform to the current written specifications authorized by
RLWS. RLWS warrants the equipment against faulty workmanship and defective materials. If any equipment fails
to conform to these warranties, RLWS will, at its option, repair or replace such goods returned within the warranty
period subject to the following conditions:
• Upon discovery by Buyer of such nonconformity, RLWS will be given prompt written notice with a
detailed explanation of the alleged deficiencies.
• Individual electronic components returned to RLWS for warranty purposes must be packaged to prevent
electrostatic discharge (ESD) damage in shipment. Packaging requirements are listed in a publication,
Protecting Your Components From Static Damage in Shipment, available from RLWS Equipment Return
Department.
• Examination of such equipment by RLWS confirms that the nonconformity actually exists, and was not
caused by accident, misuse, neglect, alteration, improper installation, improper repair or improper testing;
RLWS shall be the sole judge of all alleged non-conformities.
• Such equipment has not been modified, altered, or changed by any person other than RLWS or its duly
authorized repair agents.
• RLWS will have a reasonable time to repair or replace the defective equipment. Buyer is responsible for
shipping charges both ways.
• In no event will RLWS be responsible for travel time or on-location repairs, including assembly or
disassembly of equipment, nor will RLWS be liable for the cost of any repairs made by others.
THESE WARRANTIES EXCLUDE ALL OTHER WARRANTIES , EXPRESSED OR IMPLIED , INCLUDING WITHOUT
LIMITATION WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NEITHER RLWS
NOR DISTRIBUTOR WILL, IN ANY EVENT, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
RLWS AND BUYER AGREE THAT RLWS’ SOLE AND EXCLUSIVE LIABILITY HEREUNDER IS LIMITED TO REPAIR
OR REPLACEMENT OF SUCH GOODS. IN ACCEPTING THIS WARRANTY, THE BUYER WAIVES ANY AND ALL OTHER
CLAIMS TO WARRANTY.
SHOULD THE SELLER BE OTHER THAN RLWS, THE BUYER AGREES TO LOOK ONLY TO THE SELLER FOR
WARRANTY CLAIMS.
NO TERMS, CONDITIONS, UNDERSTANDING, OR AGREEMENTS PURPORTING TO MODIFY THE TERMS OF THIS
WARRANTY SHALL HAVE ANY LEGAL EFFECT UNLESS MADE IN WRITING AND SIGNED BY A CORPORATE
OFFICER OF RLWS AND THE BUYER.
© 2011 Rice Lake Weighing Systems, Inc. Rice Lake, WI USA. All Rights Reserved.
RICE LAKE WEIGHING SYSTEMS • 230 WEST COLEMAN STREET • RICE LAKE, WISCONSIN 54868 • USA
14
KLU Series Universal Weighbars Operator’s Manual
For More Information
Web Site
•
http://www.ricelake.com/products/livestock-solutions
Contact Information
Hours of Operation
Knowledgeable customer service representatives are available 6:30 a.m. - 6:30 p.m. Monday through Friday and 8
a.m. to 12 noon on Saturday. (CST)
Telephone
• Sales/Technical Support 800-472-6703
• Canadian and Mexican Customers 800-321-6703
• International 715-234-9171
Immediate/Emergency Service
For immediate assistance call toll-free 1-800-472-6703
Canadian and Mexican customers please call 1-800-321-6703
If you are calling after standard business hours and have an urgent scale outage or emergency, press 1 to reach
on-call personnel.
Fax
Fax Number 715-234-6967
Email
U.S. sales and product information at
• [email protected]
International (non-U.S.) sales and product information at
• [email protected]
Mailing Address
Rice Lake Weighing Systems
230 West Coleman Street
Rice Lake, WI 54868 USA
Troubleshooting
15
16
KLU Series Universal Weighbars Operator’s Manual
230 W. Coleman St. Rice Lake, WI 54868 USA
U.S. 800-472-6703 Canada/Mexico 800-321-6703 International 715-234-9171
Europe +31 (0) 88 2349171
www.ricelake.com www.ricelake.mx www.ricelake.eu www.ricelake.co.in m.ricelake.com
© Rice Lake Weighing Systems
127469 Rev B
08/2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement