dcs keyset user guide
Table
me Page
ofDCS
Keyset
Contents
DCS KEYSET
USER GUIDE
for
OfficeServ™ 100, OfficeServ™ 500
and OfficeServ™ 7000 Series
December 2009
Samsung Telecommunications America reserves the right without prior notice to revise information in this
guide for any reason. Samsung Telecommunications America also reserves the right without prior notice to
make changes in design ir components of equipment as engineering and manufacturing may warrant.
Samsung Telecommunications America disclaims all liabilities for damages arising from the erroneous interpretation or use of information presented in this guide.
THINGS YOU SHOULD KNOW
................................................2–9
OUTSIDE CALLS
Making an Outside Call ................................................................................................10
Answering an Outside Call..........................................................................................10
Universal Answer ..........................................................................................................11
Recall/Flash ......................................................................................................................11
Busy Line Queuing with Callback ............................................................................11
Cancelling Callback........................................................................................................12
INTERCOM CALLS
Calling Other Stations ..................................................................................................13
Answering Intercom Calls ..........................................................................................13
Answer Modes ................................................................................................................14
Busy Station Callback....................................................................................................14
Busy Station Camp-on..................................................................................................14
Calling Your System Operator....................................................................................15
CALL PROCESSING
Holding Calls ............................................................................................................16–17
Transferring Calls ....................................................................................................18–19
Transfer with Camp-On ................................................................................................18
Transfer to Voicemail ....................................................................................................19
Call Waiting ......................................................................................................................19
Conference Calls ............................................................................................................19
Forwarding Calls......................................................................................................20–22
Call Pickup ........................................................................................................................23
My Group Pickup............................................................................................................23
Privacy Release................................................................................................................23
Speed Dialing ..................................................................................................................25
Programming Personal Speed Dial Numbers ..............................................25–26
One Touch Speed Dialing............................................................................................26
Last Number Redial ......................................................................................................27
Manual Retry with LNR ................................................................................................27
Save Number with Redial............................................................................................27
Chain Dialing....................................................................................................................27
Automatic Redial/Retry................................................................................................28
Pulse to Tone Changeover ..........................................................................................28
Memo Redialing..............................................................................................................28
PAGING AND MESSAGING
Making an Internal Page..............................................................................................29
Making an External Page ............................................................................................29
All Page ..............................................................................................................................29
Meet Me Page..................................................................................................................30
Call Park and Page ..................................................................................................30–31
Messages—Set and Cancel ........................................................................................31
Returning Messages......................................................................................................32
Programmed Messages................................................................................................32
CONVENIENCE FEATURES
Do Not Disturb ................................................................................................................33
One Time DND ................................................................................................................33
Mute ....................................................................................................................................33
Background Music ........................................................................................................33
Established Call Pick-Up ..............................................................................................34
Appointment Reminder/Alarm Clock ....................................................................34
Door Phone Calls ............................................................................................................35
Executive/Secretary Hot Line ....................................................................................35
Group Listening ..............................................................................................................36
Account Codes ................................................................................................................36
Locking Your Keyset ......................................................................................................37
Manual Signalling ..........................................................................................................37
Off-Hook Voice Announce ..........................................................................................38
OHVA Block ......................................................................................................................39
OHVA Reject ....................................................................................................................39
In Group/Out of Group ................................................................................................39
CS Keyset
....................................................................................1
of Contents
ABOUT THIS BOOK
DIALING FEATURES
ome Page
TABLE OF CONTENTS
ADD-ON MODULE
AME PASSWORD ............................................................................................................40
Auto Camp-On ................................................................................................................40
Select Ring Tone ............................................................................................................40
Change Your Passcode ................................................................................................40
Set Answer Mode (Intercom) ....................................................................................41
Set Answer Mode (CO) ................................................................................................41
Automatic Hold ..............................................................................................................41
Headset Operation ........................................................................................................41
Hot Keypad ......................................................................................................................42
Key Confirmation Tone ................................................................................................42
Rejoining a Page ............................................................................................................42
Ring Preference ..............................................................................................................42
Display Speed Dial Name ............................................................................................43
Caller ID Review All........................................................................................................43
Secure OHVA ....................................................................................................................43
Configure Mobile Extensions (MOBEX)..................................................................43
32 Button Module with Keyset / 64 Button Module with Keyset...................58
DISPLAY FEATURES
Interactive Display Keys ..............................................................................................45
Directory Information ................................................................................................ 45
Call Log ..............................................................................................................................46
Dial by Name....................................................................................................................46
Call Progress Displays ..................................................................................................46
Display Number Dialed ................................................................................................47
Call Duration Timer........................................................................................................47
Auto Timer ........................................................................................................................47
Timer Function ................................................................................................................47
Viewing Message Indications ....................................................................................48
Alarm Reminder Messages ........................................................................................48
Personal Speed Dial Names........................................................................................49
Station Names ................................................................................................................49
Managing Key Assignments ......................................................................................49
LCR with Clear..................................................................................................................50
Backspace with LCR ......................................................................................................50
Text Messaging ........................................................................................................51–52
Caller ID / ANI / CLI ................................................................................................53–57
Samsung Voicemail
................................................................................59
Subscriber Services Menu Diagram .................................................................60–61
Accessing your Mailbox ...............................................................................................62
Getting Started ...............................................................................................................63
Listen to your Messages ..............................................................................................64
Subscriber Services Menu ..........................................................................................63
Listening to Old or New Messages ..........................................................................64
Group New or Old Messages .....................................................................................65
Record and Send a Message......................................................................................65
Access Manager ............................................................................................................66
Personal Greetings ........................................................................................................68
Mailbox Administration ...............................................................................................70
Message Broadcast .......................................................................................................72
Personal Services ...........................................................................................................73
Personal Administration Settings ...........................................................................74
Keyset User Features ....................................................................................................75
Shortcuts .................................................................................................................77
Interactive Displays ....................................................................................................77
E-Mail Gateway (EMG)............................................................................................77-79
PERSONAL SPEED DIAL NUMBERS ..............................80–81
CS Keyset
of Contents
ome Page
CUSTOMIZING YOUR KEYSET
CS Keyset
of Contents
ome Page
ABOUT THIS BOOK
Your keyset is the most visible part of the OfficeServ System. No matter what
model keyset you are using, with or without a display, telephone calls are handled
in the same way. The LCD 12B and LCD 24B keysets have a few additional conveniences that are not available to STD 24B, Basic 12B and 7B keyset users. These are
noted throughout this guide.
Please take the time to study this guide and to become familiar with the operation
of your keyset. Keep this guide handy. You may need to look up instructions for
infrequently used features.
Learning to use your keyset correctly will make everyday telephone communications a breeze.
This book is written based on the factory default settings for the feature access
codes. Sometimes, due to programming requirements, these codes may be
changed. If you find that a feature code does not work as described in this book,
please contact your installation and service company to determine the correct
code.
1
DCS telephones are called “keysets.” They contain buttons or “keys” that are used
to access or activate the many features of your office phone system. The keys with
paper designation strips are programmable keys. This means they can be programmed for a specific function on your keyset and that same button can be
something different on another keyset. See the system manager to get your most
frequently used features assigned to your programmable keys. When changes are
made, be sure that your programmable keys are relabeled properly.
Lines from the telephone company are “C.O. lines.” Calls on these lines are referred
to as “outside calls.”Your system can have individual C.O. line keys or lines may be
assigned to groups. When they are in a group, you access a line by dialing an
access code or pressing a route button. For example, dial 9 or press the LOCAL key
to get a local outside line. If Least Cost Routing is used, pressing the LCR key will
automatically select a preprogrammed C.O. line according to what digits are
dialed. Each line in the system is numbered, beginning with 701, then 702, 703, etc.
Direct Station Selection (DSS) keys are programmed to ring specific stations. You
can press a DSS key instead of dialing the extension number. A DSS key lights red
when that station is busy (Busy Lamp Indication).
OfficeServ 100, OfficeServ 500, and OfficeServ 7000 Series systems provide distinctive ring patterns to your keyset:
•
•
•
Outside calls have a single ring tone repeated.
Internal calls have a double ring tone repeated.
Door phone calls and alarm/appointment reminders have a triple ring tone
repeated.
CALL INDICATIONS
The keys on your phone have light emitting diodes (LEDs). Some of these are tricolored LEDs that light green, red or amber (green and red together). Some of the
keys can only light red.
Some simple rules to remember:
•
•
•
•
•
•
•
•
Any steady LED indicates the line or feature is in use.
A fast flashing green LED indicates a new call ringing in.
A slow flashing green or red LED indicates a call is on hold.
A slow flashing amber LED indicates a recall to your keyset.
A steady red LED on the HOLD key indicates the keyset is locked.
A steady red LED on the TRSF key indicates the keyset is Forward All.
A steady red LED on the ANS/RLS key indicates the keyset is in Headset mode.
A flashing red LED on the ANS/RLS key indicates the keyset is in DND mode.
SPEAKERPHONE
Pressing the ANS/RLS or the MONITOR key will answer or release a call on the
speakerphone. Switching from the handset to the speakerphone is easy. Press the
SPK key and hang up the handset.
NOTE: The 7B phone is not a speaker phone. If you are using a 7B phone, you must
lift the handset in order to speak to the other party.
VOLUME CONTROLS
DCS keysets use the UP and DOWN keys to adjust the ringer volume while the
keyset is ringing, the speaker volume while the speakerphone or monitor speaker
is in use and the handset volume while you are listening.These three levels will be
stored in memory until changed. If background music is turned on at your keyset,
the volume keys will also control the level of music. The volume of pages heard
through the speaker of a keyset can be adjusted during a page announcement by
using the volume keys. There are 16 levels for each volume setting. The volume of
off-hook ring is controlled by a user-programmable setting.
Intercom calls, also called internal calls, always appear on your CALL buttons.They
will always light green.You can have up to eight CALL buttons, but at least two are
recommended.
2
3
CS Keyset
USER ORIENTATION
of Contents
ome Page
THINGS YOU SHOULD KNOW
Outside calls appear on individual line keys if they are assigned. When an individual line is not assigned to its own key, it will appear on a CALL button.Your outside
calls will light green on your keyset and red on other keysets.
You never lose sight of your calls while they are on hold.They stay right where you
put them and are identified with a green flashing light if the key has a tri-colored
LED.
The system provides several tones to assist you. Some of these tones are already
familiar to you.
LABELING PROGRAMMABLE KEYS
Intercom Dial Tone—A steady tone that indicates you can begin dialing.
DIAL TONE
CS Keyset
LCD 24B KEYSET LAYOUT
of Contents
ome Page
SYSTEM TONES
Insert the end of a paper clip into the notch of the clear cover. Push
the cover sideways. Lift the cover and remove the designation strip.
Label the designation strip. Replace the strip and cover.
CONTINUOUS
Ringback Tone—Indicates the station you dialed is ringing.
RINGBACK TONE—1000 ms ON/3000 ms OFF
32 CHARACTER DISPLAY Two
lines with 16 characters each.
CONTINUOUS
SOFT KEYS Used to
activate features via
the display.
16 PROGRAMMABLE
KEYS WITH TRICOLORED LIGHTS
Used for CALL buttons,
intercom calls, outside
lines and many other
system features.
Busy Tone—Indicates the station you dialed is busy.
BUSY TONE—500 ms ON/500 ms OFF
CONTINUOUS
DND/No More Calls Tone—Fast busy tone indicates the station you
dialed is in the Do Not Disturb mode or cannot receive any more calls.
SCROLL
DND/NO MORE CALLS TONE—250 ms ON/250 ms OFF
FOR TEN SECONDS
Transfer/Conference Tone—Indicates your call is being held and you
can dial another party.
VOL
TRANSFER/CONF TONE—100 ms ON/100 ms OFF
CONTINUOUS
SPK
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
Confirmation Tone—Very short beeps followed by dial tone indicate you
have correctly set or canceled a system feature.
CONFIRMATION TONE—50 ms ON/50 ms OFF
FOR ONE SECOND
(programmable)
Error Tone—A distinctive two level beeping tone indicates you have
done something incorrectly. Try again.
ERROR TONE—50 ms of tone 1/50 ms of tone 2
FOR THREE SECONDS
4
SCROLL KEY Used to
scroll through displays.
TRSF
A N S/
RLS
SPEAKER For handsfree
operation and ringing.
ANSWER/RELEASE KEY
TRANSFER KEY
HOLD KEY
0OPER
PULLOUT
DIRECTORY TRAY
8 PROGRAMMABLE
KEYS WITH RED
LIGHTS Used to call
stations directly, to indicate busy conditions of other stations, for One Touch dialing and many other
system features.
VOLUME CONTROL
KEYS Used to set independent levels for handset,
speaker, background music, ring and
page volumes.
MICROPHONE For
handsfree operation.
SPEAKER KEY Used to switch
call to speakerphone.
5
CS Keyset
of Contents
ome Page
LCD 12B KEYSET LAYOUT
STD 24B KEYSET LAYOUT
LABELING PROGRAMMABLE KEYS
LABELING PROGRAMMABLE KEYS
Insert the end of a paper clip into the notch of the clear cover. Push
the cover sideways. Lift the cover and remove the designation strip.
Label the designation strip. Replace the strip and cover.
Insert the end of a paper clip into the notch of the clear cover. Push
the cover sideways. Lift the cover and remove the designation strip.
Label the designation strip. Replace the strip and cover.
32 CHARACTER DISPLAY Two
lines with 16 characters each.
SOFT KEYS Used to
activate features via
the display.
16 PROGRAMMABLE
KEYS WITH TRICOLORED LIGHTS Used
for CALL buttons, intercom calls, outside lines
and many other system
features.
SCROLL KEY Used to
scroll through displays.
6 PROGRAMMABLE
KEYS WITH TRICOLORED LIGHTS
Used for CALL buttons,
intercom calls, outside
lines and many other
system features.
DIGITA L
C O MMU NIC ATIO N
SYSTEM
8 PROGRAMMABLE
KEYS WITH RED
LIGHTS Used to call stations directly, to indicate
busy conditions of other
stations, for One Touch
dialing and many other
system features.
SCROLL
VOL
SPK
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
TRSF
A N S/
RLS
SPEAKER For handsfree
operation and ringing.
ANSWER/RELEASE KEY
TRANSFER KEY
HOLD KEY
6
0OPER
PULLOUT
DIRECTORY TRAY
6 PROGRAMMABLE
KEYS WITH RED
LIGHTS Used to call
stations directly, to indicate busy conditions of other stations, for One Touch dialing and many other
system features.
VOL
SPK
MICROPHONE For
handsfree operation.
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
TRSF
VOLUME CONTROL
KEYS Used to set independent levels for handset,
speaker, background music, ring and
page volumes.
1
0OPER
A N S/
RLS
ANSWER/
RELEASE KEY
SPEAKER For handsfree
operation and ringing.
PULLOUT
DIRECTORY TRAY
MICROPHONE For
handsfree operation.
VOLUME CONTROL
KEYS Used to set independent levels for handset,
speaker, background music, ring and
page volumes.
SPEAKER KEY Used
to switch call to
speakerphone.
HOLD KEY
TRANSFER KEY
SPEAKER KEY Used to switch
call to speakerphone.
7
CS Keyset
of Contents
ome Page
BASIC 12B KEYSET LAYOUT
7B KEYSET LAYOUT
LABELING PROGRAMMABLE KEYS
LABELING PROGRAMMABLE KEYS
Insert the end of a paper clip into the notch of the clear cover. Push
the cover sideways. Lift the cover and remove the designation strip.
Label the designation strip. Replace the strip and cover.
Insert the end of a paper clip into the notch of the clear cover. Push
the cover sideways. Lift the cover and remove the designation strip.
Label the designation strip. Replace the strip and cover.
DIGITA L
C O MMU NIC ATIO N
SYSTEM
VOL
SPK
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD
TRSF
3 PROGRAMMABLE
KEYS WITH TRICOLORED LIGHTS
(1, 2, 3) Used for CALL
buttons, intercom
calls, outside
lines
and many other system features.
6 PROGRAMMABLE
KEYS WITH TRICOLORED LIGHTS Used
for CALL buttons,
intercom calls, outside
lines and many other
system features.
0OPER
A N S/
RLS
6 PROGRAMMABLE
KEYS WITH RED LIGHTS
Used to call stations
directly, to indicate busy
conditions of other
stations, for One Touch
dialing and many other
system features.
CALL 1
3
4
5
PULLOUT
DIRECTORY
TRAY
6
HOLD
7
VOLUME CONTROL
KEYS Used to set
independent levels for
handset,
s p e a k e r,
background music, ring
and page volumes.
VOLUME
MONITOR
1
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PRS
8 TUV
9 WXY
HOLD KEY
ANSWER/RELEASE KEY
8
FLASH
2
TRANSFER
SPEAKER KEY Used to
switch call to speakerphone.
SPEAKER
For handsfree operation and
ringing.
CALL 2
1
0OPER
TRANSFER KEY
MICROPHONE
For handsfree operation.
TRANSFER KEY
SPEAKER For handsfree
operation and ringing.
4 PROGRAMMABLE
KEYS WITH RED
LIGHTS (4, 5, 6, 7)
Used to call stations
directly, to indicate
busy conditions of
other stations, for One
Touch dialing and
many other system features.
HOLD KEY
MONITOR KEY
VOLUME CONTROL
KEYS Used to set independent levels for
handset,
speaker,
background
music,
ring and page volumes.
PULLOUT
DIRECTORY TRAY
9
•
•
Lift the handset and press an idle outside line button, line group button or dial
a line access code to receive dial tone—OR—to use the speakerphone, press
an idle outside line button, line group button or dial a line access code to
receive dial tone through the speaker—OR—press SPK or the MONITOR key
if you are using a 7B phone, receive intercom dial tone and dial a line access
code.
Dial the telephone number.
Finish the call by replacing the handset or pressing the ANS/RLS key.
NOTE: You will receive No More Calls tone when you attempt to make a call and
there is no key available for that line.
•
•
•
If Least Cost Routing is enabled on your phone system, this button may be
labeled LCR or accessed by dialing an access code (usually 9).
If your system is programmed to require an authorization code before making
a call, dial ! plus a valid code before selecting a C.O. line.
If your system is programmed to require an account code before making a call,
press the ACCT button or dial 47 plus a valid bin number, press the ACCT button again, or !, and then select a C.O. line.
CS Keyset
•
of Contents
MAKING AN OUTSIDE CALL
UNIVERSAL ANSWER
ome Page
OUTSIDE CALLS
Outside lines may be programmed to ring a general alerting device. To answer
calls ringing this device, dial 67 or press the UA key.This device can operate in any
one of the six different ring plans.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key if you are using a 7B phone before dialing.
RECALL DIAL TONE
Press the NEW button to disconnect your existing call, wait for dial tone and then
make a new call on the same line.
NOTE: If this button does not appear on your keyset, the FLASH key may be programmed to recall dial tone.
SENDING A FLASH
While on an outside call, press the FLASH key to send a flash to the telephone
company. This is required for some custom calling features or CENTREX use.
NOTE: Flash is not available on an ISDN circuit.
BUSY LINE QUEUING WITH CALLBACK
For more information on authorization and account codes, see your system
administrator.
If you receive a busy signal when you are selecting an outside line, this means that
the line or group of lines is busy.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key if you are using a 7B phone before dialing.
•
•
•
ANSWERING AN OUTSIDE CALL
•
Lift the handset and you are automatically connected to the ringing call.
See Ring Preference under Customizing Your Keyset—OR—press the ANS/RLS
key to automatically answer on the speakerphone.
NOTE: If a call is flashing at your keyset but not ringing, you must press the flashing button to answer.
10
Press the CBK key or dial 44. You will hear confirmation tone.
When the line becomes free, the system will call you back.
Lift the handset or press the ANS/RLS key to answer, wait for dial tone and dial
the telephone number or speed dial number again.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you have set a
callback, your CBK key will light.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before dialing.
11
Your phone may have a maximum of five callbacks to lines and/or stations set at
a time. To cancel a callback:
•
•
Press the CBK key or dial 44. You will hear confirmation tone.
While you are listening to confirmation tone, press the HOLD key.This will cancel the oldest set callback.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset or press SPK or the MONITOR key if you are using the 7B phone before dialing.
INTERCOM CALLS
CS Keyset
A callback will be canceled if not answered within 30 seconds. If you have set a
callback, your CBK key will light.
of Contents
ome Page
CANCELLING CALLBACK
CALLING OTHER STATIONS
•
•
•
Dial the extension number or group number.
Wait for the party to answer. If you hear a brief tone burst instead of ringback
tone, the station you called is set for Voice Announce or Auto Answer. Begin
speaking immediately after the tone.
Finish the call by replacing the handset or pressing the ANS/RLS or the MONITOR key if you are using a 7B phone.
NOTES:
1. If you have a DSS key assigned to an extension or station group, you may press
this key instead of dialing the number. If you are using a 7 Button Set you must
pick up the handset to speak to the calling party.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK or the MONITOR key if you are using a 7B phone before you begin
dialing.
ANSWERING INTERCOM CALLS
•
•
When your keyset rings, simply lift the handset—OR—press the ANS/RLS key
to be connected to the calling station. If you are using a 7B phone you must
pick up the handset to speak to the calling party.
Finish the call by replacing the handset or pressing the ANS/RLS or the MONITOR key if you are using a 7B phone.
See Ring Preference under Customizing Your Keyset.
VOICE ANNOUNCE MODE
When another station calls you, your keyset will sound a brief attention tone and
you will hear the caller’s announcement.
•
•
Press ANS/RLS to turn on the microphone and speak handsfree—OR— lift the
handset to reply.
To finish the call, replace the handset or press the ANS/RLS key.
NOTE: In order for C.O. calls to be answered handsfree, AUTO ANS CO must be set
to ON.
12
13
•
Your microphone and speaker are turned on and you can speak handsfree. For
privacy, use the handset. If you are using a 7B phone you must pick up the
handset to speak to the calling party.
To finish the call, replace the handset or press the ANS/RLS or the MONITOR
key if you are using a 7B phone.
NOTE: In order for C.O. calls to be answered handsfree, AUTO ANS CO must be set
to ON.
BUSY STATION CALLBACK
When you call another station and receive a busy signal:
•
•
•
Press the CBK key or dial 44.
When the busy station becomes free, your keyset will ring.
Lift the handset or press ANS/RLS to call the now idle station.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before you begin dialing.
AUTO CAMP-ON
When you want to automatically camp on to a busy station without pressing the
camp on button every time you call a busy station, you can set your phone for auto
camp-on.
•
•
•
With the handset on-hook, press TRSF and then dial 110.
Dial 081 to turn on auto camp-on or 080 to turn it off.
Press TRSF to store your selection.
CALLING YOUR SYSTEM OPERATOR
•
•
Dial 0 to call your system operator or group of operators.
If you want to call a specific operator, dial that person’s extension number.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK before you begin dialing.
NOTES:
1. A callback will be canceled if not answered within 30 seconds. If you have set a
callback, your CBK key will light.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before dialing.
BUSY STATION CAMP-ON
When you call another station and receive a busy signal but you do not want to
wait for a callback:
MANUAL CAMP-ON
•
•
•
•
Press the CAMP key or dial 45.
The called station will receive off-hook ring tone repeated every few seconds
and its first available CALL button will flash green to indicate your call is waiting.
Wait for the called party to answer.
The called station must release its first call or place it on hold before answering
your camp-on.
NOTES:
1. If you receive No More Calls tone, that station has no available key to accept
your call. Hang up or leave a message.
14
15
CS Keyset
•
of Contents
When another station calls you, your keyset will sound a brief attention tone and
then automatically answer the call.
ome Page
AUTO ANSWER MODE
•
When you are connected to any call, press HOLD. The call will flash green at
your keyset. If this call appears on a line key at other keysets, it will flash red at
those keysets.
To take the caller off hold, press that key and the green flashing light will go
steady green again. Resume the conversation.
NOTE: While on a call, pressing a line key, route key or flashing CALL button will
automatically put your first call on hold and connect you to the new call. See
Automatic Hold under Customizing Your Keyset.
EXCLUSIVE HOLD
To place an outside call on hold at your phone so that other users cannot get it:
•
•
Press the HOLD button twice. The call will flash green on your keyset and this
line will show a steady red light on other keysets.
To retrieve the call, press the flashing green line button or press the HOLD button a third time.
NOTE: Intercom calls will always be placed on exclusive hold.
REMOTE HOLD
When you wish to place a call on hold at another station.Press TRSF and dial the station number (or press the appropriate DSS key). Press the HOLD key. This will place
the call on system hold on an available CALL button or Line Key at the remote station and return you to dial tone.
CS Keyset
•
of Contents
SYSTEM HOLD
HOLD RECALL
ome Page
CALL PROCESSING
If you leave a call on hold longer than the hold timer, it will recall your station. The
button that the call appears on will have a slow flashing amber light.
•
•
When your phone rings, lift the handset or press the ANS/RLS key to answer
the recall. If you are using a 7B phone you must use the handset to talk to the
calling party.
If you do not answer this recall within a pre-programmed period of time, it will
go to the system operator.
CONSULTATION HOLD
When you are talking on an outside line and it is necessary to consult with another extension:
•
•
•
•
Press the TRSF key; you will receive transfer dial tone. Your call is placed on
transfer hold.
Dial the extension number.
Consult with the internal party.
Press TRSF to return to the outside party or hang up to transfer the call.
NOTE: Repeatedly pressing the TRSF key will toggle between the outside party
and internal extension. If necessary you may disconnect either one of the parties
by pressing the DROP button.
RETRIEVING CALLS HELD AT
ANOTHER STATION
When a line is on hold and it appears on your keyset, press the line button with the
red flashing light.
NOTES:
When a line is on hold and it does not appear on your keyset, dial 12 plus the line
number or the extension number of the station that placed the call on hold.
1. If the destination station does not have any free CALL buttons or line keys you
will hear No More Calls tone and must return to the other party by pressing the
TRSF key (or the RETURN soft key on a display keyset).
2. Intercom calls cannot be remote held.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press the SPK key before you begin dialing.
16
17
CS Keyset
of Contents
ome Page
TRANSFERRING CALLS
TRANSFER TO VOICEMAIL
Transfer is used to send any call to another extension in one of two ways. You can
do a screened transfer by informing the other extension who is calling or you can
do a blind transfer without notification.
This feature is used to send a call directly to a voice mailbox.Your keyset must have
a correctly programmed VT key to accomplish this. To transfer a call directly to a
voice mailbox:
While on a call, press the TRSF key and dial an extension number or group
number. Your call is automatically put on transfer hold.
OR
Press a DSS key or station group key. Your call is automatically put on transfer
hold.
Hang up when you hear ringing (this is an unscreened or blind transfer). OR
Wait for the called party to answer and advise him/her of the call and hang up.
If the transfer is refused, you will be reconnected to the outside line when the
called station hangs up or you can press TRSF to return to the outside party. If
you wish to send the call to another extension without waiting for the first station to hang up, simply press another DSS button.
OR
Press the CALL button or C.O. line key to return to the outside party and begin
the transfer process again.
•
•
When you are transferring a call to a keyset set for Voice Announce or Auto
Answer, the transferred call will always ring.
•
•
•
NOTES:
1. After the inside party answers, you may alternate back and forth between the
parties by pressing the TRSF key.
2. If you receive No More Calls tone, that station has no key available to receive
another call. Press TRSF to return to the other party.
3. You cannot transfer an Intercom call by pressing a DSS key. You must press the
TRSF key and dial the destination extension number.
TRANSFER WITH CAMP-ON
When you are transferring a call to another station and you receive a busy signal,
you may camp the call on to this station. Simply hang up when you hear the busy
signal. The called party will be alerted that a call is waiting for them.
NOTE: If you receive No More Calls tone, that station has no key available to receive
another call. Press TRSF to return to the outside caller.
While on a call, press the VT key and dial the mailbox number.
Hang up when dialing is completed.
CALL WAITING
If an outside call has been camped-on to your phone or another station has
camped-on to you:
•
•
Your keyset will ring and the call that is waiting for you (camped-on) will flash
green.
Press the flashing button to answer; your other call will go on hold automatically if your station has the Automatic Hold feature set. If not, you must press
HOLD and then the flashing button.
OR
Finish the first call and hang up; the waiting call will ring.
Lift the handset or press the ANS/RLS key to answer.
NOTE: Intercom calls will not go on Automatic Hold.
CONFERENCE CALLS
You may conference up to five parties (you and four others) in any combination of
outside lines and internal stations in any order.
•
•
•
•
While engaged in a conversation, press the CONF key and receive conference
tone.
Make another call, either intercom or outside, press the CONF key and receive
conference tone.
Make another call or press the CONF key to join all parties.
Repeat the last step until all parties are added.
NOTE: When attempting to add another party to the conference and you are not
able to reach the desired person, hang up. Simply press the CONF key again to
return to your previous conversation.
To drop a party from your conference call:
•
•
18
Press CONF and dial the extension or line number that is to be dropped.
Press CONF again to reestablish the conference.
19
•
Press any one of the outside line buttons. That outside line will remain steady
green to indicate you are still connected to it. All other outside lines in the conference will be placed on system hold at your keyset. All intercom callers in the
conference will be disconnected. You may now speak with each caller privately and transfer them as usual or reestablish another conference.
FORWARDING CALLS
You may forward your calls to another station, group of stations or an external
telephone number. Program a destination for the type of forwarding you want as
detailed below. If you have FWD ALL, FWD BUSY and FWD NO ANSWER keys,
press one to turn that forward feature on. A steady red light reminds you what forward condition is activated.
You can clear all call forward conditions set at your station by lifting the handset
and dialing 600.
FORWARD ALL CALLS
To forward all your calls under any condition:
•
•
Dial 601 plus the destination you want the call to forward to.
Receive confirmation tone and hang up.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before you begin dialing.
2. The station that receives a Forwarded All call can transfer the call to the forwarded station.This is useful when you are expecting an important call but you
do not wish to be disturbed by other calls.
20
3. When a station user places his/her keyset in Forward All mode and he/she does
not have a FORWARD ALL key, the TRSF key will light to indicate Forward All
has been set and calls to this station have been transferred elsewhere.
FORWARD BUSY
To forward calls when you are on the phone:
•
•
Dial 602 plus the destination you want the call to forward to.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK before you begin dialing.
FORWARD NO ANSWER
To forward calls when you do not answer:
•
•
Dial 603 plus the destination you want the call forward to.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK before you begin dialing.
FORWARD BUSY/NO ANSWER
If you have both a Forward on Busy destination and a Forward No Answer destination programmed, you may set both of these at the same time:
•
•
Dial 604.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key if you are using a 7B phone before you begin
dialing.
FORWARD FOLLOW ME
When you want all calls to your extension forwarded to the extension where you
are now:
•
•
Dial 606 plus your extension number.
Receive confirmation tone and hang up.
21
CS Keyset
If you are the controlling party of a conference and your keyset has the Auto Hold
feature turned on (see customizing your keyset) and all of the outside lines
involved in the conference appear as buttons on your keyset, you can split the conference into separate calls as follows:
of Contents
CONFERENCE SPLITTING
ome Page
NOTE: To leave the conference, hang up. Control is passed to the next internal station. If there are no internal stations and you wish to leave outside lines connected together in a trunk to trunk conference, press the CONF key plus the CALL button that the call appears on or follow the instructions to drop a party and use your
extension number. When they hang up, the lines will release automatically. Press
CONF to rejoin a trunk to trunk conference.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK before you begin dialing.
CS Keyset
Dial 606 plus the desired extension number.
Receive confirmation tone and hang up.
STATION CALL PICKUP
of Contents
•
•
ome Page
If you want a specific extension’s calls forwarded to your phone (Remote Call
Forward):
To pick up (answer) a call ringing at another station, lift the handset and dial 65
plus the extension number of the ringing phone.
If you have a DP key assigned with a station number, you only need to press this
DP key with the flashing light to answer this ringing station.
FORWARD DND
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or MONITOR before you begin dialing.
To forward your phone when you activate DND.
GROUP CALL PICKUP
•
•
Dial 605 plus the destination you want the call to forward to.
Receive confirmation tone and hang up.
NOTE: If the Hot Keypad feature has been turned off you must first lift the handset
or press SPK before you begin dialing.
CALL FORWARD OPTIONS
A display keyset may review or change call forward options and destinations. Call
forward access can be done via the keypad or by accessing the keyset display features. To review or change call forward options:
•
•
•
•
•
Press TRSF 102.
The display will indicate the current call forward condition and destination
OR
Show 0: FORWARD CANCEL to indicate no forward is set.
Dial 0 to cancel current condition
OR
Dial 1-5 to select forward type
OR
Press UP or DOWN to select forward type.
Press the right soft key to move the cursor.
Dial the destination number (e.g., 202) OR
Press UP or DOWN to select the destination.
Press the right soft key to move the cursor.
Dial 1 to set OR
Press UP or DOWN to select YES or NO.
Press TRSF to store and exit.
To pick up (answer) a call ringing in any pickup group, lift the handset and dial 66
plus the desired group number or press the flashing GROUP PICKUP key if available.
GROUP NUMBERS
01-10
OfficeServ 7030
01-20
OfficeServ 100, OfficeServ 7100, OfficeServ 7200-S
01-99
OfficeServ 500 M
01-99
OfficeServ 500 L
01-99
OfficeServ 7200 and OfficeServ 7400
NOTES:
1. A group pickup key can have an extender for a specific pickup group.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK or the MONITOR key if you are using a 7B phone before dialing the
access code.
MY GROUP PICKUP
If desired, a new access code can be assigned to pickup ringing calls in the same
pickup group as you are in. Like “66” above except you do not need to dial the
desired group number. See your installation company for the assigned access
code. MY GROUP PICKUP:__________________.
PRIVACY RELEASE
This feature will allow another station to join in on your conversation by releasing
privacy on the C.O. from your phone.
To Release Privacy: While on you are talking on a C.O. line and you wish to have
other internal parties (or up to three) join the conversation:
•
22
Press the PRB key (the PRB key will light steady red). Inform the other party
that he/she may now join the conversation.
23
•
•
Press the C.O. line key that he/she has indicated.
OR
Dial the C.O. line number that he/she has indicated.
CS Keyset
To Join a Non-Private Conversation: When someone has informed you that you
can join a conversation:
DIALING FEATURES
of Contents
ome Page
After the other party (or parties) has joined the conversation and you wish to
return privacy to the line so that no one else can join the conversation, press the
PRB key a second time, the PRB key LED will be off.
SPEED DIALING
You can dial a preprogrammed telephone number stored in the system-wide
speed dial list of numbers 500–999 or from your personal list of numbers 00–49.
Your system may be set for 950 system wide numbers. If so the system speed dial
access codes are 050~999 and the station speed dial codes are 000~049.
•
•
•
With the handset on-hook, press the SPD key or dial 16.
Dial the desired speed dial number.
The telephone number is automatically dialed for you.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or MONITOR before you begin dialing.
PROGRAMMING PERSONAL SPEED DIAL
NUMBERS
You can program frequently dialed telephone numbers in a personal speed dial
list. A station may be assigned up to fifty numbers, 00–49. See your system administrator to determine the amount assigned to your station.
•
•
•
•
•
While on-hook, press TRSF and then dial 105.
Dial a speed dial number (00–49).
Dial a line or line group access code.
Dial the telephone number to be stored (24 digits maximum). It can include #,
!, FLASH and PAUSE.
Press TRSF to store the number.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key if you are using a 7B phone before you begin
dialing.
24
25
CS Keyset
LAST NUMBER REDIAL
of Contents
ome Page
12 BUTTON KEYSET
PROGRAMMABLE KEYS LAYOUT
24 BUTTON KEYSET
PROGRAMMABLE KEYS LAYOUT
To redial the last telephone number you dialed, press the LNR key or dial 19.
NOTES:
A
B
C
D
E
F
A
B
C
D
E
F
For the purposes of programming speed dial numbers, the programmable keys in
the bottom row are known as A, B, C, D, E and F and are defined below.
•
•
•
•
•
•
•
The A key is not used.
The B key inserts a flash.
The C key inserts a pause.
The D key is used for pulse to tone conversion. If your system uses rotary (or
pulse) dialing C.O. lines, pressing D while entering a speed dial number causes
all subsequent digits to be sent as DTMF tones.
The E key is used to hide digits. Display keyset users may want to hide some
speed dial numbers so that they will not show in the display. When you are entering a telephone number, press E. All subsequent digits will be hidden. Press
E again to begin displaying digits.
The F key is used to enter a name. See Personal Speed Dial Names under Display
Features.
Use the HOLD key to clear a speed dial number.
ONE TOUCH SPEED DIALING
You may assign any speed dial number to an already existing One Touch Speed
Dial button for quick and easy dialing of frequently used numbers.
•
•
•
•
While on-hook, press TRSF and then dial 107.
Press a One Touch Speed Dial button.
Dial the speed dial number (00–49 or 500–999) that you want assigned to this
button.
Press TRSF to store your selection.
To call this telephone number, just press the One Touch Speed Dial button.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key if you are using a 7B phone before you begin
dialing.
26
1. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK or MONITOR before you begin dialing.
2. Redial does not apply to intercom calls.
MANUAL RETRY WITH LNR
While you are on an outside call listening to a busy signal and you want to redial
the same number dialed.
•
Press the LNR key.
This will hang up your existing call and manually redial the same number dialed.
You can repeat this operation for a limited number of attempts.
SAVE NUMBER WITH REDIAL
To save the number you just dialed for later use, press the SNR key before hanging
up.
To redial this saved number at any time, press the SNR key or dial 17.The same line
will be selected for you.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK or the MONITOR key if you are using a 7B phone before you begin
dialing.
2. The saved telephone number is stored in memory until you save another.
3. Redial does not apply to intercom calls.
CHAIN DIALING
You may manually dial additional digits following a speed dial number or chain as
many speed dial numbers together as required:
•
After the first speed number is dialed, press SPD again and dial another speed
number OR manually dial additional digits following a speed dial number.
27
•
•
•
When you hear a busy signal, press the RETRY button.
The system will reserve the line and automatically redial the same number for
you. You will hear the call being made through the keyset speaker. The microphone is muted.
When the called party answers, lift the handset or press the flashing SPK to
begin speaking.
CS Keyset
When you are making an outside call and you receive a busy signal, the system can
automatically redial the number for you. It will automatically redial at a pre-programmed interval for up to 15 attempts.
of Contents
ome Page
AUTOMATIC REDIAL/RETRY
PAGING AND MESSAGING
MAKING AN INTERNAL PAGE
To make an announcement through the keyset speakers in the idle condition:
•
•
•
•
Lift the handset.
Press the PAGE key or dial 55.
Dial the desired zone number 0, 1, 2, 3 or 4.
After the attention tone, make your announcement.
PULSE TO TONE CHANGEOVER
NOTES:
1. If you have a dedicated page zone button, it is not necessary to press PAGE
and dial a zone number.
2. If allowed by your system administrator you may be able to initiate a page
from a speakerphone by pressing the PAGE key or dialing 55 without lifting
the handset.
When making an outside call on a dial pulse line, press #. All digits dialed after the
# with be sent as tones.
MAKING AN EXTERNAL PAGE
MEMO REDIALING
To make an announcement through the external paging speakers:
NOTES:
1. If you make another call, auto-redial is canceled.
2. To cancel a retry, lift and replace the handset.
When you are calling directory information, you can store the number you are
given using the SAVE feature. There is no need for pencil and paper.
•
•
•
While you are talking on an outside call, press SAVE.
Dial the telephone number as it is dictated to you on the key pad.
Press SAVE to store the number.
To dial the number, press the SNR button. It will select the same line and dial the
stored number. If necessary, you can select a different line and then press the SNR
button.
•
•
•
•
Lift the handset.
Press the PAGE key or dial 55.
Dial the desired zone number 5, 6, 7 or 8 OR
Dial 9 to page all external zones.
After the attention tone, make your announcement.
NOTES
1. If you have a dedicated page zone button, it is not necessary to press PAGE
and dial a zone number.
2. If allowed by your system administrator you may be able to initiate a page
from a speakerphone by pressing the PAGE key or dialing 55 without lifting
the handset.
ALL PAGE
To page all designated keysets in internal zone 0 and all external zones at the same
time:
•
•
•
28
Lift the handset.
Press the PAGE key or dial 55.
Dial ! or press the ALL PAGE key.
29
MEET ME PAGE
•
•
•
•
•
•
•
Lift the handset.
Press the Meet Me Page (MMPG) key or dial 54.
Dial the desired zone number.
After the attention tone, instruct the paged person to dial 56.
Press WAIT or TRSF.
Remain off-hook until the person dials 56 from any phone.
The paged person will be automatically connected with you.
CALL PARK AND PAGE
•
•
•
CS Keyset
NOTES
1. The LED on the PAGE button will only light when an All Page is in progress.
2. If allowed by your system administrator you may be able to initiate a page
from a speakerphone by pressing the PAGE key or dialing 55 without lifting
the handset.
AUTOMATIC PARK WITH PAGE KEY
of Contents
After the attention tone, make your announcement.
ome Page
•
While in conversation, press the PAGE button. The call is automatically parked
at your station.
Receive page tone and dial a desired page zone number.
Make announcement indicating your extension number or the line number.
Hang up.
To retrieve an automatically parked call:
•
•
Dial 10 plus the number that was announced. If you have a PAGPK key, press it
and dial the number that was announced. If you have a PARK key, press it and
dial the announced orbit number.
You will be connected to the parked call.
NOTES:
1. If the call is not retrieved within a pre-programmed period of time, it will recall
your keyset and have a slow amber light. You cannot park and page intercom
calls.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before you begin dialing.
When you have an outside call for someone who is not at his/her desk, you can
park the call prior to paging.The OfficeServ 100, the OfficeServ 500, and OfficeServ
7000 Series systems offer two different methods:
SETTING A MESSAGE INDICATION
MANUAL PARK ORBITS
When you are calling another station and no one answers or you receive a busy
signal, you can leave a message indication:
•
•
•
•
While in conversation, press the PARK button.
Enter a desired orbit number (0-9), if the orbit number is busy dial another
orbit number. Display users can press ! to automatically place the call in any
available orbit number and see the number in the display.
Remember the selected orbit number and replace the handset when finished.
Lift the handset and make a page announcement as previously described
(example:“John Smith park two”).
To retrieve a parked call from orbit:
•
•
Press the PARK button and dial the announced orbit number (0-9).
You will be connected to the parked call.
NOTES:
1. You must have a PARK button or park access code to retrieve and place calls in
park orbits.
2. If the call is not retrieved within a pre-programmed period of time, it will recall
your keyset and have a slow amber light. You cannot park and page intercom
calls.
3. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before you begin dialing.
30
•
•
Press the MSG key or dial 43 and receive confirmation tone.
Hang up. The MSG key on the called station will light. Standard telephones
receive special dial tone as a message indication or a lit message lamp, if the
phone is equipped with one and they are connected to a 16MWSLI card on the
system.
NOTES:
1. A station can have up to five message indications.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before you begin dialing.
CANCELING MESSAGES
To cancel a message indication that you left at another station, dial 42 plus the
extension number of the station at which you left a message.
To cancel all message indications left at your keyset, dial 42 plus your extension.
Your MSG light will go out.
31
•
•
•
Press the MSG key or dial 43. The first station that left a message will be called
automatically. If that station does not answer, your MSG light will stay on.
Repeat until all messages have been returned in the order received.
Your MSG light will turn off when all messages have been returned.
NOTES:
1. Display keyset users can view message indications and return them in any
order. See Viewing Message Indications under Display Features.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK or the MONITOR key if you are using a 7B phone before you begin
dialing.
3. If a message has been left at your keyset by a keyset in Auto Answer, you must
manually cancel the message after it has been returned.
CS Keyset
RETURNING MESSAGES
of Contents
ome Page
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK before you begin dialing.
CONVENIENCE FEATURES
DO NOT DISTURB
Use this feature when you want to block calls to your keyset.
•
•
While on-hook, press the DND key or dial 401. The DND key lights steady red
to remind you of this mode.
To cancel DND, press the DND key again or dial 400. The DND light turns off.
You can make calls while in the DND mode.
NOTES:
1. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK or the MONITOR key.
2. If you place your keyset in DND mode and you do not have a DND key, your
ANS/RLS key will flash to indicate DND status.
PROGRAMMED MESSAGES
ONE TIME DND
When you will be away from your phone for any length of time, you can leave a
programmed station message. Display stations calling you will see this message
and be informed of your status or follow your instructions.
If you are on a call and you do not wish to be interrupted while on that call, you
can press the DND key and place your station in Do Not Disturb. When you hang
up at the end of the call, DND will be automatically canceled and your keyset will
be able to receive new calls. This feature requires a DND key.
•
•
•
Dial 48 plus any message code (01-20) listed on the back of this user guide.
To cancel any of these messages you might have selected, dial 48 plus 00.
Press TRSF to exit and store your selection.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK before you begin dialing.
NOTE: This feature will not affect any calls currently ringing your keyset.
MUTE
You can mute the handset transmitter or the microphone during any conversation:
You can have multiple programmed message keys (PMSG) and each one can have
a different message code:
•
•
•
BACKGROUND MUSIC
•
Press any programmed message (PMSG) button. The message is set and the
button will light red. Press the button again to turn off.
Pressing another programmed message (PMSG) button will turn the previous
one off and set a different programmed message.
Press the MUTE key. It will light red.
To resume speaking, press the MUTE button again. The light turns off.
When a music source is supplied, you may listen to music through the speaker in
your keyset:
•
•
While on-hook, press the HOLD button to hear music.
Press the HOLD button again to turn music off.
You can set the level of background music by using the VOL keys while listening
to the music. This does not affect the speakerphone level.
32
33
To pick up an established call in progress at a single line extension connected to a
computer modem on your PC.
When you are programmed to receive calls from a door phone:
•
•
Press the EP key for that station on your keyset and the call is automatically
moved to your keyset.
The single line extension on your modem will be disconnected.
NOTE: You must have an assigned (EP key) button on your regular keyset, for the
single line station.
APPOINTMENT REMINDER/ALARM CLOCK
This feature works like an alarm clock. Use it to remind yourself of an appointment
later in the day (TODAY ONLY) or as a daily reminder every day (DAILY).You can set
up to three alarms. Each one can be either a TODAY ONLY or a DAILY alarm.
When the alarm rings, you will hear three short rings repeated three times. Lift the
handset to answer the alarm. If you do not, the alarm will alert you two more times
at five minute intervals.
To set alarms:
•
•
•
•
•
•
Press TRSF and then dial 112.
Dial the alarm number 1, 2 or 3.
Dial the time at which you want the alarm to sound. Enter the time as HHMM
(hours and minutes) using the 24 hour clock.
Dial 0 (NOT SET), 1 (TODAY ONLY) or 2 (DAILY) to select the alarm type.
Press TRSF to save.
Repeat for each alarm if needed.
•
•
•
Press TRSF and then dial 112.
Dial alarm number 1, 2 or 3.
Press the HOLD key.
NOTE: Display keysets can show a reminder message. See Alarm Reminder
Messages under Display Features.
34
You will receive three short rings repeated.
Lift the handset or press ANS/RLS or the MONITOR key. You are connected to
the door phone.
If an electric door lock release is installed, dial 13 to unlock the door.
CALLING THE DOOR PHONE/ROOM
MONITOR
You may call the door phone and listen to what may be happening outside or in
another room.
• Dial the extension number of the door phone.
• You will be connected to the door phone and you can listen or have a conversation.
• If an electric door lock release is installed, dial 13 to unlock the door.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key.
EXECUTIVE/SECRETARY HOT LINE
If programmed, an executive and a secretary can have a hot line between them.
When the executive station is in the DND mode, all of its calls will ring the secretary station. If the secretary does not answer, the caller will go to the secretary’s
voicemail box if setup.
•
•
To cancel individual alarms:
•
•
•
CS Keyset
ANSWERING THE DOOR PHONE
of Contents
ome Page
ESTABLISHED CALL PICKUP
Either person can press the BOSS key to make a voice call to the other station.
Using the hot line will override DND at the other station. This key will light red
when the other station is in use.
To transfer a call to a Boss in DND:
•
•
•
Press the TRSF key followed by the BOSS key.
Wait for the BOSS station to answer, then announce the call and hang up to
complete the transfer OR
Hang up to complete a blind transfer after pressing the BOSS key.
35
CS Keyset
of Contents
ome Page
GROUP LISTENING
LOCKING YOUR KEYSET
When you are engaged on a call and you are using the handset, you may want
other people to hear the distant party’s voice over the speaker:
• Press the LISTEN key to turn on the speaker. The microphone is not in use, so
the distant party does not hear other parties present in your office.
• Press LISTEN again to turn the speaker off and resume private conversation.
• Repeat if necessary.
You can lock your keyset to control misuse of your phone while you are away. You
can unlock it when you return. Your default station passcode is 1234.
NOTE: Depending on speaker volume and the acoustics of your office, it may be
advisable to turn the group listening feature off before hanging up. This will eliminate a momentary squeal.
ACCOUNT CODES
When enabled, your system allows calls to be charged to different accounts. You
can enter account codes either by dialing the full code, by entering an account
code “bin number”, or by pressing your ACC key if one is assigned. Bin numbers are
a 3 digit short code that will automatically insert the appropriate account code.
Account codes may be a maximum of 12 digits (# may be used); if the account
code is to be less than 12 characters you may end the code by pressing ! or the
right soft key. The type of code used is determined by your telephone system
administrator. Codes can be entered before or during a call as follows:
To enter an account code before placing the call:
•
•
•
•
Press your ACC key or dial 47.
Dial the account code or bin number.
You will receive a confirmation tone and display.
When prompted dial a trunk or trunk group (i.e. 9) and the telephone number
to call.
To enter an account code by interrupting the conversation:
•
•
While on an outside call press the ACC key or press TRANSFER followed by 47.
Dial the account number or bin number (if you are entering an account code
you will need to press your ACC key or right soft key to finalize the entry)
NOTE: If you make an error simply repeat the procedure with the correct code.
Only the most recent account code dialed will be recorded.
36
0
UNLOCKED
1
LOCKED OUTGOING
Hold Button LED Flashes
NO
ACCESS DENIED
2
LOCKED ALL CALLS
Hold Button LED Solid
Make outside calls
YES
Receive outside calls
YES
YES
NO
Make intercom calls
YES
YES
NO
Receive intercom calls
YES
YES
NO
Make 911 calls
YES
YES*
NO
•
•
•
•
NO
While on-hook, press TRSF and then dial 100.
Dial your four digit station passcode.
Dial 1 for locking outgoing, 2 for locked all calls or 0 to unlock.
Press TRSF to store your selection.
NOTE: When your keyset is locked for outgoing, the HOLD key will flash. When
your keyset is locked for all calls, the HOLD key will light steady.
MANUAL SIGNALLING
Use this feature when you want to send a brief 500ms ring burst to another station, regardless of the status of your phone (on-hook, off-hook, handsfree, DND or
ringing).
To send a signal to another station:
•
•
Press the Manual Signalling (MS) key.
You may press the MS key repeatedly to send multiple signals to the designated station.
NOTE: Your phone must have a Manual Signalling (MS) key with a station number
extender assigned to it.
37
Keysets may receive a voice announcement while on another call. The calling station must have an OHVA key.When you are in DND, you cannot receive OHVA calls.
The OHVA feature will work with intercom calls and transferred calls.
NOTES:
To make an off-hook voice announcement:
•
•
•
•
Dial the extension number or press the DSS key.
When you receive a busy signal, press the OHVA key.
After the attention tone, begin speaking.
Finish the call by replacing the handset or pressing the ANS/RLS or the MONITOR key if you are using a 7B phone.
NOTES:
1. When you are voice announcing to a station close to you, use the handset to
avoid an echo effect.
2. You cannot off-hook voice announce to single line telephones.
If your keyset is associated with a DCS 32 Button Add-On Module (DCS 32 AOM is
not supported on the OfficeServ 7100, OfficeServ 7030), you can receive Executive
OHVA calls. Executive Off-Hook Voice Announce allows you to engage in conversation on your keyset and simultaneously receive and reply handsfree to an OHVA
through your DCS 32 Button Add-On Module (AOM). Use caution because the conversation through the AOM may possibly be heard by the caller on the keyset.
When you receive an off-hook voice announcement, if you are using the handset,
you will hear the announcement over the handset receiver. If you are using the
speakerphone, you will hear the announcement over the keyset speaker. In both
cases, you can continue to speak to the original party.
•
•
Press the flashing CALL button on your keyset.This will place the original party
on hold and allow you to talk to the announcing party.
To return to your first party, press the key corresponding to your original call.
This will disconnect the OHVA call.
Executive off-hook voice announce allows you to engage in conversation on your
keyset and simultaneously receive and reply handsfree to an OHVA through your
add-on module (AOM). Use caution because the conversation through the AOM
may possibly be heard by the caller on the keyset. When you receive an executive
OHVA through your AOM:
•
•
38
Reply by speaking in the direction of the microphone in the AOM unit.
Adjust the volume with the VOL keys on the AOM unit.
Press the SPK or the MONITOR key on the AOM to disconnect the announcing
party.
1. Executive off-hook voice announce can only be accomplished when an AOM is
attached to your phone.
2. If the MUTE key on the AOM is lit, you must press the AOM’s SPK key to answer
the OHVA call.
OHVA BLOCK
Your keyset can be programmed with an OHVA Block (BLOCK) key. Pressing this
key will prevent anyone from making an OHVA to you until you press the button
again and cancel the blocking.
OHVA REJECT
Your keyset can be programmed with an OHVA Reject (REJECT) key. Pressing this
key while receiving an OHVA call will disconnect the voice announcing party and
return you to your original call.
IN GROUP/OUT OF GROUP
If your keyset is assigned to a station ring group, you can remove your keyset from
the group and then put it back in. While you are out of the group, you can receive
calls to your extension number but not calls to the group number. If you have an
IN/OUT key with the group number assigned.
•
•
Press the IN/OUT key. It will light red when your keyset is in the group.
Press the IN/OUT key again to exit the group and turn the light off. Repeat as
necessary.
If you do not have an IN/OUT key:
•
Dial the IN/OUT access code number __________, then the group number,
then 0 to exit the group or 1 to enter the group.
NOTE: If the Hot Keypad feature has been turned off, you must first lift the handset
or press SPK or the MONITOR key.
The IN/OUT key can include an extender to indicate the specific group that this
key will affect. This means that if you are in multiple groups, you can decide for
which groups you will receive calls.
39
CS Keyset
•
of Contents
ome Page
OFF-HOOK VOICE ANNOUNCE
This feature allows people using the AME feature to enable password protection.
This will prevent unauthorized people from listening to your messages being left.
The passcode is the same as your station passcode. This feature only applies if
there is an SVM card installed in the system and your keyset has a programmed
AME key.
•
•
•
With the handset on-hook, press TRSF and then dial 110.
Dial 101 to turn on AME PASSWORD or 100 to turn it off.
Press TRSF to store your selection.
AUTO CAMP-ON
This option allows intercom calls to be automatically camped on, if possible, when
a busy station is called.
•
•
•
With the handset on-hook, press TRSF and then dial 110.
Press 081 to turn CAMP-ON on or 080 to turn it off.
Press TRSF to store your selection.
SELECT RING TONE
Each keyset user can select any one of eight ring frequencies:
•
•
•
While on-hook, press TRSF and then dial 111.
Dial 1–8 or press the UP and DOWN keys to hear each tone.
When you hear the tone that you prefer, press TRSF to save it.
NOTE: Specific lines or stations may be programmed to ring with a different tone
than what you have selected for you keyset.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234.You can change your station passcode whenever you desire.
•
•
•
•
•
40
While on-hook, press TRSF and then dial 101.
Dial your old passcode.
Dial a new passcode (must be four characters). You can use 0–9.
Redial the new passcode to verify. If successful, you will hear two beeps. Four
beeps indicate an incorrect code. Reenter the code again.
Press TRSF to store the new passcode.
CS Keyset
AME PASSWORD
SET ANSWER MODE (INTERCOM)
of Contents
ome Page
CUSTOMIZING YOUR KEYSET
You can receive internal calls in one of three modes (see Answering Intercom Calls
under Intercom Calls for descriptions):
•
•
•
While on-hook, press TRSF and then dial 103.
Dial 0 for Ringing, 1 for Auto Answer or 2 for Voice Announce.
Press TRSF to store your selection.
NOTE: When your keyset is programmed for Auto Answer and you have Forward
No Answer (FNA) turned on, you must answer screened transfers by pressing
ANS/RLS or the MONITOR key if you are using a 7B phone before your FNA timer
expires or the call will forward.
SET ANSWER MODE (CO)
Your incoming CO calls can be set to follow the intercom answer mode.
•
•
•
•
While on-hook, press TRSF and then dial 110.
Dial 15 to access AUTO ANS CO.
Press the VOLUME UP or DOWN key to change the status.
Press TRSF to store your selection.
AUTOMATIC HOLD
While on an outside call, pressing a line key, route key or a flashing CALL button
will automatically put your call on hold and connect you to the next call. This feature can be turned on or off at your keyset.
•
•
•
With the handset on-hook, press TRSF and then dial 110.
Dial 001 to turn Automatic Hold on or 000 to turn it off.
Press TRSF to store your selection.
NOTE: Intercom calls can only be automatically put on hold by pressing TRSF.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When using
headset mode, press the ANS/RLS or the MONITOR key if you are using a 7B
phone to answer and release calls.
•
•
•
With the handset on-hook, press TRSF and then dial 110.
Dial 021 to use the headset or 020 to use the handset.
Press TRSF to store your selection.
41
HOT KEYPAD
•
•
•
Your keyset’s keypad can be made “live”or “hot”so that it is not necessary to lift the
handset or press SPK or the MONITOR key before you begin dialing. Calls can be
made and features activated by simply dialing the C.O. line number, trunk group
access code, intercom number or feature access code. To activate this feature:
•
•
•
With the handset on-hook, press TRSF and then dial 110.
Dial 031 to turn the Hot Keypad on or 030 to turn it off.
Press TRSF to store your selection.
KEY CONFIRMATION TONE
You can hear a short beep (confirmation tone) each time you press a button on the
dial pad. This tone can be turned on or off.
•
•
•
While on-hook, press TRSF and then dial 110.
Dial 040 to turn tones off or 041 to turn tones on.
Press TRSF to store your selection.
REJOINING A PAGE
This feature allows you to hear the remaining portion of an ongoing internal page
after you return your keyset to idle. To enable this feature:
•
•
•
With the handset on-hook, press TRSF and then dial 110.
Dial 051 to turn this feature on or 050 to turn it off.
Press TRSF to store your selection.
RING PREFERENCE
This feature automatically answers ringing calls when you lift the handset or press
the ANS/RLS or the MONITOR key if you are using a 7B phone. This method will
always answer calls in the order they arrived at your keyset. When you turn ring
preference off, you must press the flashing button to answer a call, allowing you to
answer calls in the order you choose.
•
•
•
42
With the handset on-hook, press TRSF and then dial 110.
Dial 061 to turn ring preference on or 060 to turn it off.
Press TRSF to store your selection.
CS Keyset
DISPLAY SPEED DIAL NAME
of Contents
ome Page
Your keyset may be equipped with a Headset mode key. If it is so equipped pressing this key while the light is out will cause the keyset to enter headset mode and
the light will illuminate to indicate this. Pressing the key while the light is lit will
cause the keyset to return to handset mode and the light will go out.
This option allows you to view the name associated with a speed dial number as
it is dialed.
With you handset on-hook, press TRANSFER and then dial 110.
Press 111 to turn DISP SPDNAME on or 110 to turn it off.
Press TRANSFER to store your selection.
CALLER ID REVIEW ALL
This feature allows display keyset users to review Caller ID information for calls
sent to their stations.This list can be from ten to fifty calls in a first in, first out basis.
The list includes calls that you answered and calls that rang your station but that
you did not answer. When reviewing this list, you can press one button to dial the
person back. The system must be using LCR to dial the stored number.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 121 to turn CID REVIEW ALL on or 120 to turn it off.
Press TRANSFER to store your selection.
SECURE OHVA
This option allows you to receive OHVA calls via the speaker while you are on the
handset.
•
•
•
With you handset on-hook, press TRANSFER and then dial 110.
Press 131 to turn AUTO CAMP-ON on or 130 to turn it off.
Press TRANSFER to store your selection.
CONFIGURE MOBILE EXTENSIONS (MOBEX)
This feature allows you to configure options for any Mobile Extension (MOBEX)
ports that are assigned to you by your telephone system administrator. You can
turn a port on or off; set the telephone number for the port; or set the caller ID you
will be calling in from.The caller ID field has no effect unless you have been authorized as an Executive MOBEX user. Check with your telephone system administrator
for further details on your specific system configuration.
To set the phone number a MOBEX port can reach you on:
•
•
•
•
Press TRANSFER and then dial 126.
Dial your station pass code.
Dial the number of the port you wish to configure (1-5) (you may also use the
Volume Up and Volume Down keys to select a port and press the right soft key
to confirm).
Dial 0 to select the telephone option.
43
•
•
•
•
•
•
Press TRANSFER and then dial 126.
Dial your station pass code.
Dial the number of the port you wish to configure (1-5) (you may also use the
Volume Up and Volume Down keys to select a port and press the right soft
key to confirm).
Dial 1 to select the caller ID option.
Dial the phone number you will be calling in from.
Press TRANSFER to store your selection and exit programming.
To turn a MOBEX port ON or OFF:
•
•
•
•
•
•
Press TRANSFER and then dial 126.
Dial your station pass code.
Dial the number of the port you wish to configure (1-5) (you may also use the
Volume Up and Volume Down keys to select a port and press the right soft
key to confirm).
Dial 2 to select the activation status option.
Dial 0 to turn the port on, dial 1 to turn the port off.
Press TRANSFER to store your selection and exit programming.
CS Keyset
To set the caller ID of the location you will be calling in from:
DISPLAY FEATURES
of Contents
•
Dial the number of a C.O. line to use when making calls to this MOBEX port.
Dial the phone number you can be reached at by users calling this MOBEX
port.
Press TRANSFER to store your selection and exit programming.
ome Page
•
•
INTERACTIVE DISPLAY KEYS
The three keys below the display are substitutes for dedicated feature keys and access codes. Pressing one of these keys has the same effect as pressing a programmable key. These keys are called soft keys as their functions are not fixed. They
change to present you with the best options for that call condition.The use of soft
keys allows the programmable keys to be used for more DSS and speed dial keys.
The SCROLL key is used to display options available to the user at a particular time
or during a specific procedure. Press this key once while in the idle state to view
the three main categories available.
201: STN NAME
CALL OTHER ANS
ANSWER: Guides you through the options to answer calls.
OTHER: Guides you through features other than making or answering calls.
CALL: Guides you through the options to make a call.
Select one of the main categories: CALL, OTHER or ANS (ANSWER). Press the
SCROLL key to display additional options available under each of the three main
categories. The symbol " displayed as the last character on the lower line of the
display indicates that there are additional options. Press the SCROLL key to display
these additional options.
User instructions will be displayed in lower case letters. Options assigned to soft
keys will be in upper case letters.
DIRECTORY INFORMATION
An 11 character directory name can be assigned to each extension number.
Display keyset users can view the name of the called or calling station before answering.
Each outside line can have an 11 character directory name. Incoming calls can be
easily identified and answered with different greetings.
Outside and internal calls ringing to a station group will display [CALL FOR xxx]
where xxx is the station group number. This allows you to answer calls directed to
you differently than calls directed to your group.
44
45
•
•
•
•
•
•
Press the LOG key.
Press either the IN or OUT key.
View the first IN/OUT telephone number. At this point you may select one of
the three options related to this number or use the UP/DOWN keys to scroll
through your list of calls.
Press the CLEAR key yo erase this number from the list.
Press the NND key repeated to view the Name, Number, or Date associated
with this call.
Press the DIAL key to call this number.
These options are the same for the incoming or outgoing call logs.
DIAL BY NAME
Each station or speed dial number can have an associated directory name. A station or speed dial number can be selected by scrolling alphabetically through a
directory name list. This on-line “phone book” allows the user to look up and dial
any station or speed dial number in seconds.
•
•
•
•
•
Press the DIR key (DIRECTORY).
Select the directory you wish to use: PERS (personal speed dial numbers), SYS
(system speed dial numbers) or STN (station names).
Dial the key on the keypad that corresponds to the first letter of the name you
wish to search for.
Use the UP and DOWN arrows to scroll through the names.
Press the DIAL soft key to dial the number.
NOTE: A DIR key can have an extender to take you directly to one of the above lists,
(PERS, SYS, or STN).
formed of what is happening and where you are. In some conditions you are
prompted to take an action and in other cases you receive directory information.
DISPLAY NUMBER DIALED
Display keysets begin showing digits as they are dialed. They will stay in the display until the call duration timer comes on automatically or the TIMER button is
pressed. If the call duration timer is not used, the number dialed will be displayed
until the call is released, transferred or put on hold.
CALL DURATION TIMER
The system can be set to automatically time outside calls. A few seconds after you
dial a telephone number, the timer appears in the display. It appears immediately
for incoming calls. The call timer continues for the duration of the call. Call duration times are displayed in minutes and seconds. If a call lasts longer than 60 minutes, the timer restarts.
You can press the TIMER key to manually begin timing a call. Press it again to stop
timing. If you press it while the automatic timer is on, the call duration time is
restarted.
AUTO TIMER
Display keyset users may have the timer automatically start when they answer
incoming calls or after a short delay on an outgoing call.
•
•
•
With the handset on-hook, press TRSF and then dial 119.
Dial 41 to turn the auto timer on or 40 to turn it off.
Press TRSF to store your selection.
TIMER FUNCTION
Display keyset users may use this feature as a simple stopwatch.
•
•
•
•
When the keyset is idle, press the TIMER button to start timing.
Press the TIMER button again to stop timing.
Read the elapsed time in the display.
Lift the handset and replace it. The display will return to date and time.
CALL PROGRESS DISPLAYS
During everyday call handling, your keyset display will provide information that is
helpful and in some cases invaluable. Displays like [CALL FROM 203], [TRANSFER
TO 202], [701: RINGING], [TRANSFER FM 203], [708 busy], [Camp on to 204], [Recall
from 204], [Call for 501], [message from 204] and [FWD ALL to 204] keep you in46
47
CS Keyset
To view your incoming and outbound call logs:
of Contents
The system can log both incoming and ooutgoing calls placed from or to your
telephone.You must have a LOG button programmed on your keyset and assigned
a review list. Each IN and OUT list can be up to 50 numbers maximum. They are
assigned in blocks of 10 each.
ome Page
CALL LOG
•
With the handset on-hook, press the MSG key with the red flashing light.
The first station that left a message indication will be displayed.
Press the UP and DOWN arrows to scroll through the stations that left message
indications. Use the soft keys to reply, clear or advance to the next message.
Press the ANS/RLS key to return your keyset to the idle condition.
ALARM REMINDER MESSAGES
When you use the alarm/appointment reminder feature, you create a 16 character reminder message. When the alarm rings, your message will appear instead of
[ALARM REMINDER]. To program reminder messages:
•
•
•
•
•
•
•
Press TRSF and then dial 116.
Dial the alarm number 1, 2 or 3.
Dial the time you want the alarm to go off. Enter the time as HHMM (hours and
minutes) using the 24 hour clock.
Dial 0 (NOT SET), 1 (TODAY) or 2 (DAILY) to select the alarm type.
Write your message using the dial pad keys. Each press of a key selects a character. Pressing the next key moves the cursor to the next position. For example,
if your message is “TAKE MEDICATION,” press 8 once to get the letter “T.” Press
2 once to get “A.” Press 5 twice to get “K.” Continue selecting characters from
the following table to complete your message.
Press the TRSF key to store the alarm and reminder message.
Repeat for each alarm if needed.
X
DIAL !
:
=
Y
(
[
]
9
!
NOTE: When the character you want appears on the same dial pad key as the
previous character, press UP to move the cursor one space to the right.
To cancel an individual alarm and reminder message:
•
•
•
•
Press TRSF and then dial 112.
Dial alarm number 1, 2 or 3.
Press the HOLD key.
Press the TRSF key.
PERSONAL SPEED DIAL NAMES
Each personal speed dial number can have an 11 character name assigned to it.
This name is used to select the speed dial bin when you are dialing by directory.
•
•
•
•
•
Press TRSF and then dial 106.
Dial the speed dial bin number 00–49.
Write your message using the procedure described in Alarm Reminder Messages.
Press the TRSF key to store the speed dial name.
Repeat for each speed dial bin if necessary.
STATION NAMES
You can assign an 11 character name to your keyset. This allows other display keyset users to call you using the directory dial feature.
To program a station name:
COUNT
1
2
3
4
5
DIAL 0
Q
Z
.
)
0
DIAL 1
space
?
,
!
1
DIAL 2
A
B
C
@
2
•
DIAL 3
D
E
F
#
3
DIAL 4
G
H
I
$
4
MANAGING KEY ASSIGNMENTS
DIAL 5
J
K
L
%
5
DIAL 6
M
N
O
^
6
DIAL 7
P
R
S
&
7
DIAL 8
T
U
V
!
8
48
CS Keyset
•
•
•
W
of Contents
You can view all of your message indications before you return them:
DIAL 9
ome Page
VIEWING MESSAGE INDICATIONS
•
•
Press TRSF and then dial 104.
Enter the 11 character name using the procedure described in Alarm Reminder
Messages.
Press TRSF to store the name.
You can view your key assignments and add extenders to some of your programmable keys for easy one touch operation of frequently used features.
•
•
While on-hook, press TRSF and then dial 107.
Use the VOL keys to scroll through all of your programmable keys OR press the
programmable key to which you want to add the extender.
49
DESCRIPTION
EXTENDER
BOSS ......................Boss and Secretary ..................1–4
DP ............................Direct Pickup ............................Extension or
station group number
DS ............................Direct Station ............................Any extension number
FWRD ....................Call Forwarding ......................0–7
GCONF ..................Group Conference ..................0–5
GPIK........................Group Pick-Up ..........................01–20
IG..............................In/Out of Group........................Any group number you are part of
MMPG ....................Meet Me Page ..........................0–9, !
PAGE ......................Page ............................................0–9, !
PARK ......................Park (orbits)................................0–9
RP ............................Ring Plan ....................................(1–6), HOLD for none
PMSG......................Programmed Messages ........01–30
SG ............................Station Group............................500 or 5000 through 549 or 5049
SPD..........................Speed Dialing ..........................00–49, 500–999
DIR ..........................Directory ....................................PERS (1), SYS (2) or STN (3)
VT ............................Voicemail Transfer ..................Voicemail Group number
NOTE: Confirm that the cursor is placed correctly before you enter the extender.
LCR WITH CLEAR
When you are making an outside call using LCR and dial an incorrect digit, you can
press the CLEAR soft key to reenter the telephone number. You do not need to
redial 9 to reaccess LCR.
BACKSPACE WITH LCR
CS Keyset
KEY
TEXT MESSAGING
of Contents
When you reach a key listed below, dial the corresponding extender.
Press TRSF to store and exit programming.
ome Page
•
•
This feature allows two digital keyset users to respond to each other with preprogrammed text messages. After receiving an Off Hook Voice Announcement or
Station Camp-On, you may respond with a text message while continuing to talk
and listen to your outside party. The other station can view this message and take
the appropriate action or respond back with another text message.
You must be permitted to use the Text Messaging feature. See your System
Administrator or Technician to be assigned this feature.
They will assign you ten (10) blank messages.You can create any 16 character messages (01 to 10) that are appropriate for your use.
Note: Please see ALARM REMINDER MESSAGES for instructions on how to enter
characters to create a text message.
Familiarization with the two digit message numbers you will use the most will
make this procedure quick and easy. However if you do not know them, use the
UP/DOWN button to scroll to the desired message, then press SEND.
The basics steps in text messaging are:
1.
2.
3.
4.
5.
Press TMSG soft key to begin text messaging.
Dial the 2 digit number for the desired message.
Confirm this is the intended message then press SEND.
Wait for a reply from the other station (steps 1, 2 & 3)
When any station presses EXIT the displays at both stations return to their previous call progress condition.
At all times after step 1 you can talk and listen to your caller while repeating steps
2.
If you misdial while using LCR, you can delete digits shown in the display by pressing the BSPC soft key as many times as necessary.
50
51
Talking on line 702
702:
CONF
01:15
MUTE
PAGE
701:
05:25
Press TRANSFER
Transfer:
RETURN
Caller ID is the name given to the telephone company-provided feature that delivers the telephone number and sometimes the name of the person calling your
phone. There are two types of Caller ID; the first delivers the calling party’s telephone number only and the second (sometimes referred to as “Deluxe” Caller ID)
delivers both the calling party’s telephone number and name as listed in the telephone directory.
The phone system can handle both types of Caller ID; in fact, in the case of number only delivery, the system can be programmed to insert a name for a specific
telephone number. However, even though you are paying to receive Caller ID
information, there are some circumstances that mean you will not receive this information.The six most common reasons are listed below along with the display information that the system will provide.
PRIVATE
The caller does not wish his/her name or number to be revealed to you. This type of call can be stopped at the telephone company by dialing an access code on your outside
lines. This will redirect these PRIVATE calls to an announcement that states that you do not wish to receive calls that
have had Caller ID blocked. The code to block these calls
can usually be found in the front section of the telephone
directory.
OUT OF AREA
The caller is calling from an area that cannot provide Caller ID information (for example, international calls) or
he/she is calling from a type of circuit that cannot provide
Caller ID information, for example, some outbound WATS
lines.
PAYPHONE
The caller is calling from a coin-operated telephone. The
telephone company will send this information as there are
no directory listings for pay phones. The number will be
delivered as usual.
INVALID CID INFO
This is a message that will be displayed when CID information is sent on the line but was somehow corrupted.
NO CID RECEIVED
This is a message that will be displayed when there was no
CID information sent on the line.
Dial 205
205:busy
OHVA
CAMP ON
!
OHVA to 205
OHVA from 201
TMSG
REJECT
Wait for reply
GIVE THE CALL
TMSG:01
SEND
Dial 03 or press " twice
ASK THEM TO HOLD
TMSG:03
SEND
!
ASK THEM TO HOLD
TMSG
EXIT
Wait for reply
702:
01:45
701:
MUTE
CONF
CONF
52
!
PAGE
CS Keyset
STATION 205: JOHN
is talking on line 701
of Contents
STATION 201: LINDA
received a call on line 702
WHAT IS CALLER ID?
ome Page
The following example will better demonstrate how to use Text Messaging. In this
example station 201 is making an off hook voice announcement to station 205
who after hearing the announcement will respond with a text message.
05:55
PAGE
MUTE
53
NOTE:The Caller ID features require optional software and/or hardware. Please see
your service and installation company for details.
WHAT IS ANI?
[T1&E&M NOT SUPPORTED ON THE OS 7030, OS 7100 and OS 7200-S]
ANI (Automatic Number Identification) is a feature offered by some telephone
service providers that provides the calling party’s telephone number. This service
is only available on E&M Tie Lines on a T1, digital trunk. ANI is similar to Caller
Identification (CID) but the format and information of the calling person is different. CID uses FSK signalling and ANI uses DTMF signalling. Usually, with ANI, a calling party’s identity is the Listed Directory Number (LDN) unless a separate bill-tonumber has been specified, (in which case the bill-to-number will be sent). Note
that ANI does not provide calling party NAME, only the number.The phone system
can provide calling number to name translation table.
•
•
WHAT IS CLI?
On ISDN circuits, calling party information is called CLI and is supported on both
BRI (not supported in the US) and PRI type circuits (not supported on OS 7030). On
BRI circuits the system only supports number delivery and, like ANI, a name can be
attached to the telephone number of frequent callers via the Caller ID translation
table. On 5ESS and NI2 PRI circuits both name and number support is provided on
the system.
SELECTING YOUR CALLER ID
DISPLAY
Simultaneous display of Caller ID name and number on incoming CO calls on both
lines of display keysets is supported on all OfficeServ systems. On transferred CO
calls, you can decide if you want to see the Caller ID name or Caller ID number in
the display. Regardless of which data is selected, you can press the NDD key to
view the other pieces of CID information. To select the type of Caller ID information you wish to view:
•
•
•
54
With the handset on-hook, press TRSF and then dial 119.
To set the first line of a ringing call display dial 0.
To set the second line of a ringing call display dial 1.
Set the data to display from the following:
- To show nothing dial .
•
- To show Caller ID Number dial 1.
- To show Caller ID Name dial 2.
- To show the DID Number the call came in on dial 3.
- To show the Name of the DID the call came in on dial 4.
- To show the Name of the Group the call came in for dial 5.
- To show the DID Number and then Name of the DID dial 6.
- To show the Name of the DID and then the DID Number dial 7.
To set the top line of the display shown after answering a call dial 2.
Set the data to display from the following:
- To show Caller ID Number dial 0.
- To show Caller ID Name dial 1.
- To show the DID Number the call came in on dial 2.
- To show the Name of the DID the call came in on dial 3.
- To show Caller ID Number and then the DID Number dial 4.
- To show Caller ID Name and then the DID Number dial 5.
- To show the DID Number and then the name of the DID dial 6.
- To show the Name of the DID and then the DID Number dial 7.
- To show the C.O. line information dial 8.
To set the format if the C.O. line information when the above is set to show C.O.
line information dial 3.
- To show the C.O. line number and the dialed or Caller ID Number dial 0.
- To show only the dialed or Caller ID Number dial 1.
Press TRANSFER to exit and store your selection.
VIEWING THE NEXT CALLER ID CALL
In the event that you have a call waiting or a camped-on call at your keyset, you
can press the NEXT key to display the Caller ID information associated with the
call in queue at your keyset. Either the CID name or CID number will show in the
display depending on your Name/Number selection.
To view Caller ID information for calls that have been camped-on to your keyset,
press the NEXT key. If your keyset does not have a NEXT key, press the CID key
and then the NEXT soft key.
SAVING THE CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may press
the SAVE key to save the CID number. If your keyset does not have a SAVE key,
press the CID key, the SCROLL key and then the SAVE soft key. The system must
be using LCR to dial the saved number.
55
CS Keyset
Caller ID Digital Signal Processors (CIDDSP’s) are resources
in the system required for receiving CID data. If there are
no CIDDSP’s available at the time a call comes in, this is the
message you will see on your display.
of Contents
ome Page
NO CID DSP
1. Your telephone system must have LCR correctly programmed to redial the
saved number.
2. If the Hot Keypad feature has been turned off, you must first lift the handset or
press SPK before you begin dialing.
STORING A CALLER ID NUMBER
At any time during an incoming call that provides CID information, you may save
the CID number as a speed dial number in your personal speed dial list. To store a
Caller ID number in a personal speed dial bin:
•
•
•
•
Press the STORE key.The system displays the speed dial bin in which the number was stored, OR
Press the CID key and then press the SCROLL key.
Press the STORE soft key.
The system displays the speed dial bin in which the number was stored.
NOTE: Your telephone system must have LCR correctly programmed to redial the
saved number. If LCR is not being used on your system, you will not be allowed to
STORE CID numbers.
INQUIRE CALLER ID PARK/HOLD INFO
If you are informed that an incoming call is on hold or has been parked for you,
you may view the Caller ID information before you retrieve the call. This will influence how you choose to handle the call.
From an idle keyset:
•
•
•
56
Press the INQUIRE key, OR
Press the CID key and then the INQUIRE soft key.
Dial the trunk number.
You may now answer the call by pressing ANS, OR
You may use NND to view more information about this call, OR
You can return to the idle condition by pressing IGNORE.
•
•
CS Keyset
NOTES:
•
of Contents
To redial a number that has been saved, press the SNR key or dial 17.
If you are on a call:
ome Page
REDIALING A SAVED CALLER ID
NUMBER
Press the INQUIRE key. Your existing call will go on hold, OR
Press the CID key and then the INQUIRE soft key to place the first call on hold.
Dial the trunk number.
You may now answer the call by pressing ANS, OR
You may use NND to view more information about this call, OR
You can return to the idle condition by pressing IGNORE.
NOTES:
1. If you are on an intercom call or you have Automatic Hold turned off, you must
finish the existing call or place it on hold before inquiring.
2. If you inquire about an outgoing call, you will receive a [call no longer available] display.
REVIEWING PAST CALLER ID CALLS
This feature allows you to review CID information for calls sent to your keyset.This
list can contain 10–50 calls in a last-in, first-out basis.The list includes calls that you
answered and calls that rang your keyset but that you did not answer. When
reviewing this list, you can press one button to dial the person back. The system
must be using LCR to dial the stored number.To access the CID information stored
in your REVIEW list:
•
•
•
Press the REVIEW key, OR
Press the CID key and then press the REVIEW soft key.
If you have entries in your review list, the most recent call will be shown first.
You can now CLEAR this entry, OR
Use NND to view more information about this call, OR
Press DIAL to call this person back, OR
Press SCROLL and then press STORE to save this number in a personal speed
dial bin.
NOTES:
1. Each keyset defaults with ten review bins. Please see your system administrator to determine the number of bins assigned to your keyset.
2. Your system must have LCR correctly programmed to allow you to DIAL numbers from the review list or to STORE entries from the review list.
57
[NOT SUPPORTED ON THE OS 7030 and OS 7100]
The 32 button module is used when you need more programmable keys added to
your keyset. The 32 tri-colored LED’s provide better visual indication of call status
and call progress. The extra programmable keys are used exactly like the one on
your keyset. Make them DSS/BLF keys or any combination of feature keys. The 32
button does not support executive off-hook voice announce (OHVA) and does not
have a microphone. A maximum of four 32 button modules can be assigned to any
keyset.
64 BUTTON MODULE WITH KEYSET
The 64 button module is used when you need more programmable keys added to
your keyset. The 64 red LED’s provide visual indication of calls and features. The
extra programmable keys are used exactly like the ones on your keyset. Make
them DSS/BLF keys or feature keys. As a DSS/BLF the size of the 64 button module
allows for greater call status and faster call processing.The 64 button module does
not support executive off-hook voice announce (OHVA) and does not have a
microphone. A maximum of four 64 button modules can be assigned to any keyset.
CS Keyset
32 BUTTON MODULE WITH KEYSET
Samsung Voicemail
of Contents
ome Page
ADD-ON MODULE
This section describes how to setup and use the various features available to a
Subscriber. A Subscriber is a person that has been authorized access to the various features and services available in the Samsung Voicemail. Please review this
section carefully before you use your Authorized Features and Services, known as
Subscriber Services.
Voicemail is one of the Subscriber Services available. Your voicemail box has the
capability of storing private messages, and offers a number of options for sending
or redirecting messages as well as provides several ways to notify you of new messages.
Another very common Subscriber Service is Access Manager.This allows you control over when and where you receive your calls as well as what to speak to your
callers in the event you are unable to speak to them directly. The ‘events’ are
referred to as “Call Conditions”. No-Answer, Busy, and Blocked are the most commonly used Call Conditions.
This guide can be used by Subscribers from within the office or from telephones
outside the office. The basic operation is the same, but the access method will be
different. See the Samsung Voicemail Subscriber Services Menu Diagram for more
details.
Note that some features and prompts detailed here may not be available to all
Subscribers. See your System Administrator if you have questions about feature
availability.
58
59
CS Keyset
of Contents
ome Page
Samsung Voicemail Subscriber Services Menu
y
Group New
Messages
Group Saved
Messages
11
33
Listen to New Review Saved
Messages
Messages
Group Messages Menu
1
Group
Urgent Messages
2
Group
Callback Requests
3
Group
Reminders
4
Group
Private Messages
5
Group
Fax Only Messages
6
Group
Voice Only Messages
1
Access
Manager
Personal
Greetings
Mailbox
Administration
Private Access
Numbers
Personal
Services
Pause, Resume
Executary
Play Menu
Options
Exit
Executary
2
4
5
6
7
#
8
0
*
3
Listen Menu
1
11
Save
Message
3
Discard
Message
4
Reply to Sender
5
Place
Call to Sender
55
Forward a
Copy of Message
8
Pause, Resume
Menu Prompting
7
Rewind
5 Seconds
9
Group
A Specific Sender
77
#
Play
Message Inventory
8
0
Play
Menu Options
*
Cancel, Return
Return
Subscriber Services
to Executary
99
#
##
##
Follow Me
1
Assign and/or Edit
Primary Greeting
1
Change
Message Alert
For a Directory
of Subscribers
2
Caller Access
2
Assign and/or Edit
Busy Greeting
2
Change
Pager Notification
To Create a
Reminder
3
Block All Calls
3
Assign and/or Edit
Blocking Greeting
3
Review Deleted
Messages
1
4
Call forwarding
4
Assign and/or Edit
Night Greeting
4
Review Undelivered
Messages
5
Call Screening
5
Assign and/or Edit
Screened Greeting
5
6
Find Me
6
Edit Only
Personal Greetings
7
Auto Set
Night Intercept
7
8
Pause, Resume
Menu Prompting
#
"Enter the Recipient's Number"
Deliver Copy
of Fax Message
6
9
#
Play Previous
Message
2
1
Record Menu
Play
Message
Group
Email Only Messages
7
Record & Send
Messages
Change *
Playback Volume
Pause, Resume
Message Playback
Fast Forward
5 Seconds
Change *
Playback Speed
Skip to
Next Message
Scan Messages
1
Review
Recording
2
Stop, Append to
Recording
3
Discard Recording
and Rerecord
4
Set
Delivery Options
5
Specify
Future Delivery
6
SEND Message,
Then Copy
7
Rewind
5 Seconds
77
Change *
Playback Volume
8
Pause, Resume
Record/Playback
9
Fast Forward
5 Seconds
99
Change *
Playback Speed
0
Play
Menu Options
#
SEND Message,
Then Exit Record
00
Play Message
Information
0
Play
Menu Options
*
Cancel, Return
Return
Subscriber Services
to Executary
*
Cancel,
Return
Cancel, Return
to Subscriber
Executary Services
For a Directory
of PANs
1
Review
Workload
"Enter the PAN ID Number"
2
Edit Stored
Telephone Numbers
Review
PAN Message
3
Change
Weekly Schedule
1
Change
Password
2
Record
PAN Message
5
Place a
Direct Call
2
Record
Name
Auto Play
New Messages
3
Delete
PAN message
6
Programmed
Services
3
Select
Enter Directory
Language
Name
6
Auto Play Message
Information
4
Change
Access Privilege
7
Personal
Administration
4
Extended
Prompting
Edit Only
Mailbox Greeting
8
Pause, Resume
Menu Prompting
5
Place a Direct
Call to PAN
8
Pause, Resume
Menu Prompting
8
Pause, Resume
Menu Prompting
8
Pause, Resume
Menu Prompting
9
Record &
and
Send
Record
Sent
Broadcast Message
Broadcast
Message
6
Change PAN
Message Duration
0
Play
Menu Options
Play
Access Coverage
0
Play
Menu Options
0
Play
Menu Options
7
PAN Telephone
Numbers
#
Record
a Reminder
Cancel, Return
Return
to Services
Menu
Subscriber
Services
0
Play
Menu Options
Cancel, Return
to
to Executary
Subscriber Services
8
Play
Access Statistics
0
Play
Menu Options
Cancel, Return
Return
Cancel,
toSubscriber
Executary Services
to
*
Cancel,
Return
Cancel, Return
to Subscriber
Executary Services
*
*
*
9
Clear
PAN ID Record
Cancel,
Return
Cancel, Return
to Subscriber
Executary Services
#
Save, Goto
Next PAN ID
*
0
Play
Menu Options
#
00
Access
Statistics
*
Cancel, Return
to Executary
NOTE: All options shown MAY NOT be authorized. If an option is not available
please speak to your system administrator.
*Change Playback Volume and Speed not available on the OfficeServ 7030,
OfficeServ 7100, OfficeServ 7200-S or the OfficeServ IP-UMS.
60
61
CS Keyset
of Contents
ome Page
ACCESSING YOUR MAILBOX
GETTING STARTED
[Also known as Subscriber Services Menu]
Inside Callers [Subscriber logging in from their Desk]
Using your new Subscriber Services is as simple as following a few simple spoken
instructions. First time users should read this section as a tutorial.You should start
with the following steps:
•
•
•
Dial the voicemail access number or press the key assigned to ring
the voicemail [VMMSG].
Enter your personal password when prompted (the default password is
0000).
Outside Callers [Subscribers calling from Cell Phones or outside of the
office environment]
•
•
•
Dial the phone number that will be answered by the voicemail. The main
greeting will answer.
At the main greeting dial [#] plus your Subscriber (or mailbox) number
(Subscriber and Mailbox numbers will usually match your extension number).
Enter your personal password when prompted (the default password is
0000).
Access your Subscriber Services (or Mailbox) from a Station
other than your Own (or checking a mailbox associated with a
different station)
•
•
•
Press the [VMMSG] key or dial the voicemail group number. You will be
prompted to enter a password.
Press [!]. This will take you to the Main Auto Attendant Menu.
Press [#] plus the Subscriber number of your choice. You will be prompted to
enter you password.
At this point the inside and outside callers follow the same instructions. You will
hear a message stating the number of messages left in your mailbox.You will then
hear the Subscriber Services Menu with the following options:
Access your Subscriber Services Menu - You already know how to do this.
From the Subscriber Services Menu:
•
•
•
•
•
Record a Primary/No-Answer Personal Greeting. Dial [5][1].
Record a Mailbox Greeting. Dial [5][7].
Change your access code (Password). Dial [#][7][1].
Record your name. Dial [#][7][2].
Enter your directory name. Dial [#][7][3].
After you have completed the steps above your Subscriber Services are set up and
ready to use.
LISTEN TO YOUR MESSAGES
If there are new messages in your mailbox your [VMMSG] key will be lit. Call the
voicemail by pressing this key, and when prompted enter your password. You will
then be at the Subscriber Services Menu. Select [1] to listen to new messages or
[3] to listen to saved messages.
Note: After you enter your password, if “Autoplay of New Messages”is enabled and
you have new messages the voicemail will begin to play them automatically. A
subscriber can control this feature. From the Subscriber Services Menu [6] [5] toggles “Autoplay of New Messages” ON/OFF.
SUBSCRIBER SERVICES MENU
The following is a list of all the options available in the Subscriber Main Menu.
1
LISTENING TO NEW MESSAGES
11
GROUP NEW MESSAGES
2
RECORD AND SEND A MESSAGE
3
LISTENING TO OLD MESSAGES
33
GROUP OLD MESSAGES
4
ACCESS MANAGER
Mailbox Administration - See Mailbox Administration.
5
PERSONAL GREETINGS
#
Personal Services - See Personal Services.
6
MAILBOX ADMINISTRATION
!
Return to Main Menu.
8
PAUSE / RESUME
1
Listen to New Messages - See Listening to your Message.
2
Record and Send Message - See Sending Messages.
3
Review Saved Messages - See Listening to your Message.
4
Access Manager - See Access Manager.
5
Personal Greetings - See Personal Greetings.
6
62
63
EXIT TO AUTO ATTENDANT
#
PERSONAL SERVICES
1 or 3
Change playback speed of the recording. [Not available on OS 7030,
OS 7100, OS 7200-S or OS IP-UMS]
There are two levels of speed during playback. Dialing this code will toggle
between the two speeds.
0
Play options.
Pressing this key will play all the menu options available to you from this
point.
LISTENING TO OLD OR NEW MESSAGES
00
Hear the time and date, and sender's information of the message you just
heard. Sender information is not available on outside calls.
1
Play / replay the message you just heard.
#
11
Play the previous message.
Move to the next message. This does not Save or Discard the current message - it is retained as new.
2
Save the message you just heard and listen to the next message.
##
3
Delete the message you just heard and listen to the next message.
4
Reply to the message.
Scan. Plays first 7 seconds of a message then skips to next message. This is
similar to the scan button on a radio. It will allow you to find a specific message quickly. To stop scanning press [1].
!
Cancel and return to previous menu.
This will allow you to leave a message in the mailbox of the sender (if the
sender has a mailbox on this system).
5
55
Return the call directly to the telephone number that left the message.
11 or 33
This will work for internal and external callers, but Caller ID service is needed to use this feature on an outside call.
GROUP NEW OR OLD MESSAGES
Deliver a fax copy.
This will allow you to receive attached faxmail document(s). Faxmail documents can be delivered to any fax machine of your choice as long as out
calling is authorized. You can also have faxmail messages automatically
delivered to the fax machine of your choice.
6
Forward the message and saves a copy.
The subscriber can be selected by dialing their mailbox number (nnn),
using the directory service (#) or you may also add comments and leave it
as a memo to yourself (##).
The Send and Copy Service (option 6) allows a user to send copies of a message to multiple recipients easily. A different introduction message may be
left for each recipient.
Messages can be grouped as either Reminders, press [3] or Messages from a specific sender, press [9].
Additionally you can press [#] and hear a summary of your mailbox contents:
a)
b)
c)
d)
e)
f)
Number of messages
Number of reminders
Number of urgent messages
Number of messages needing a callback
Number of private messages
Number of fax messages
2
7
Rewind the message 5 seconds.
77
Change playback volume of the recording. [Not available on OS 7030,
OS 7100, OS 7200-S or OS IP-UMS]
RECORD AND SEND A MESSAGE
There are two levels of volume during playback. Dialing this code will toggle between the two levels.
This option is used to send a message to another subscriber.The steps are simple:
8
Pause or resume during message playback.
a)
9
Fast forward the message 5 seconds.
64
Enter the recipient’s mailbox number, or if this is not known enter [#] to use
the system directory.
65
CS Keyset
!
99
of Contents
PLAY MENU OPTIONS
ome Page
0
Note: ALL Access Manager options MUST be individually allowed by the System
Administrator for each Subscriber. They are:
1
Allows the subscriber to enter an alternate location and set how long the new
destination (Designated Location) will be active. This number may be an
internal or external number. This is useful if you are frequently traveling or
changing the number where you can be reached.
When Follow Me is activated, the transfer will be supervised and confirmed.
This means that if the call is not answered or if rejected by the Subscriber at
the designated location it will be recalled to the Subscriber’s mailbox.
Setting Message Attributes
If after recording a message you select [4] you can set up any combination of the
following delivery options:
1
2
3
4
5
!
Urgent Delivery
Return Receipt Requested
Request a Call Back
Private Delivery
Reply Required
Exit
3
4
5
6
Find Me
Find Me, when enabled, will attempt to locate the subscriber by calling a list
of preprogrammed phone numbers. The stored phone numbers are entered
in 'Personal Services' [#][2] (if allowed by the Administrator). The stored telephone number list can contain up to 9 preprogrammed telephone numbers.
The Find Me feature only use the first five.
ACCESS MANAGER
66
Call Screening
If this is turned on, the caller will be asked their name and the voicemail will
play this name to you before the transfer, giving you an option to accept or
reject the call.
4
The Access Manager allows the subscriber to set a number of options for when,
where and how, and/or if the voicemail contacts you when a caller dials your
extension number. All of the options are toggled on/off based on their current status when you access them.
Call Forwarding
Unlike Follow Me where the subscriber wants to take their calls at an alternate location this feature allows the subscriber to pass control of his calls to
another Subscriber. The “Forwarded To” Subscriber will now be in control of
the caller and the caller will NOT return to originating Subscriber’s Mailbox. If
the “Forwarded To” Subscriber does not answer the caller it will now follow
what ever the “Forwarded To” Subscriber has set up for their call conditions.
The Caller will hear “Forwarding to”“{Subscriber Name}” before actually being
forwarded.
If after recording a message you select [5] to schedule future delivery, you will be
able to set message attributes and set this message as:
Immediate Delivery
Next Few Hours
End of Current Business Day (based on your Availability Schedule)
Beginning of Next Business Day (based on your Availability Schedule)
A Coming Day of the Week
Specific Day / Time
Exit
Call Blocking
When this feature is active, callers will not be transferred to your extension,
they will hear your 'blocked' greeting (if recorded) and will go directly to your
mailbox if they do not select any or are not offered any other options.
Scheduling Future Delivery
#
1
2
3
4
5
!
Follow Me
7
Night Intercept
This feature is dependent on your weekly availability schedule, which is
entered in 'Personal Services' [#][3] (if allowed by the Administrator). When
Night Intercept is active the voicemail will first ring your extension then play
67
CS Keyset
Review
Continue Recording
Discard and Re-Record
Set Message Attributes (Delivery Options)
Schedule Future Delivery
Save and Send then Send a Copy to Someone Else
Save and Send the Recording
of Contents
1
2
3
4
5
6
#
ome Page
b) Record your message at the tone. After recording the message, you will hear
the Send Menu with the following functions:
8
Pause / Resume
!
Exit from Access Manager
0
Play All Options
#
Play Access Coverage
This feature is useful for finding out how you current access settings are set.
It will also tell you what greetings will play under each of the call conditions
you have setup.
2
Played to a caller when you are already talking to someone on your extension
or the telephone at your Designated Location.
This option is available only if the Administrator has assigned you the 'Busy
Greeting' feature.
Example:“Hi, this is John Smith. I'm on another line right now. If someone else
can help you, please enter the extension number now. Or, to leave a message,
press 1.”
3
Call Blocking Greeting
Used while Call Blocking is enabled in your Access Manager or if your phone
is forwarded ALL or DND.
5
This option is available only if the Administrator has assigned you the 'Call
Blocking' feature.
PERSONAL GREETINGS
The options available in this menu will be determined by your System
Administrator, and not all of them may be available to you. In the simplest systems, only a mailbox greeting will be available, additional greetings may be accessible in more complex systems.
Example: “Hi, this is John Smith. Sorry I missed your call, but I'm going to be
out of the office for the next few hours. If someone else can help you, please
enter the extension number now. Or, to leave me a message, press 1.”
4
You may record up to 9 Personal Greetings, and you may assign any one of them
to be active. There are several different 'Call Coverage' conditions to which you
may assign any of your 9 greetings. The Call Coverage Conditions are: No-Answer,
Busy, and Do Not Disturb (or Forwarded All). This will allow different greetings to
play depending on the type of call forward that you have set, or the condition of
your telephone.
The Call Coverage conditions that you can assign specific greetings to are selected by the following digits:
Night Greeting
Used during the time period you are scheduled UNAVAILABLE, usually after
business hours during the evening and at night.
Your Personal Greeting will be played every time someone dials your extension
and you do not answer.
1
Busy Greeting
This option is available only if the Administrator has assigned you the
'Scheduling' feature.
Example:“Hi, this is John Smith. I've left the office for the evening. If you would
like to try someone else, please enter the extension number now. Or, to leave
me a message, press 1.”
5
Call Screening Greeting
Used while Call Screening is enabled, and you REJECT a caller after listening
to the caller's record name.
Primary/No Answer Greeting
This option is available only if the Administrator has assigned you the 'Call
Screening' feature.
Used when in your office, away from your desk or during the time period you
are scheduled available. If this is the only Personal Greeting you record, it will
play for all call coverage conditions.
Example:“Hi, this is John Smith. I'm sorry, but I am not available to speak with
you at this time. If someone else can help you, please enter the extension
number now. Or, to leave me a message, press 1.”
This option is available only if the Administrator has assigned you the 'Basic
Greeting' feature.
68
69
CS Keyset
Note: This does NOT use the Day and Night schedules of the phone system. It
is solely controlled by the Subscriber’s Availability Schedule.
of Contents
ome Page
Example:“Hi this is John Smith. I'm sorry I am not available to answer your call.
If someone else can help you, please enter the extension number now. Or, to
leave me a message, press 1.”
your primary, No Answer greeting during the day (when you are available)
and will NOT ring your extension but simply play your Night greeting during
the night (when you are not available).
CS Keyset
Setting Up Message Alert:
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
Select a greeting number to edit and follow the instructions to record your
greeting. When you are done recording your greeting, you will be able to listen to the greeting you recorded, save the greeting you recorded and return
to the previous menu, record the greeting again, or exit without saving the
greeting.
■
Press [1] for Message Alert.
■
There are 4 options available to you:
Press [1] to toggle message alert on and off.
Press [2] to set the schedule when you would like to be notified.
Press [3] to be notified on urgent messages only.
Press [4] to set the destination phone number.
2
Pager Notification
When this function is activated, the voicemail will call your beeper service and
notify you after each message is left in your voice mailbox.
Edit Mailbox Greeting
Used whenever a caller reaches your mailbox or if you have not recorded any
of the Call Coverage greetings. The way a caller is transferred to your mailbox
greeting directly, is by another subscriber transferring the caller to your mailbox using the VT (VoiceMail Transfer) key.
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [2] for pager notification.
■
There are 4 options available to you:
This option is available only if the Administrator has assigned you the
'Mailbox Greeting Option' feature.
Press [1] to toggle pager notification on and off.
Example: “Hi, this is John Smith. Please leave me a message, I will call you as
soon as I can.”
Press [3] to be notified on urgent messages only.
Note: This greeting will only play if none of the 5 personal greetings has
played to the caller. A common usage for this Greeting is when another
Subscriber is talking with a caller and uses the VT key on their phone to transfer the caller directly to your Mailbox.
Press [2] to set the schedule when you would like to be paged.
Press [4] to set the pager phone number.
3
MAILBOX ADMINISTRATION
The Mailbox Administration menu is used to turn on and off your pager notification, message alert options and other message control features.
Message Alert
When this function is activated, the voicemail will call any outside or inside
telephone number, after each message is left in your voice mailbox.
Undelete
When this function is activated, the voicemail will allow you to undelete any
messages that you have recently deleted (up to the programmed Daily
Maintenance Time, which is set to 3 a.m. by Default the following morning).
6
1
of Contents
Edit Personal Greetings
You may also edit/record each one of the greetings (1-9) at any time.
Note: If you record only the greeting assigned to the No-Answer Call
Coverage Condition, then that greeting will play to callers for all Call Coverage
Conditions (No-Answer, Busy, Blocked, Night, and Rejected Caller). In this case,
the salutation part of the greeting should be very general.
7
ome Page
6
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [3] for Deleted Messages.
Deleted voicemail messages are temporarily stored in memory until 3 a.m.
the following day. Select this option to recover ("undelete") previously deleted messages, during this period of time.
4
Undelivered Retrieval
When this function is activated, the voicemail will allow you to recall any messages you have sent that have NOT yet been picked up by the recipient.
To hear your message at the remote location when the voicemail calls you,
after you pick up the telephone and answer you will be instructed that there
is a message and to enter your password. Simply enter your password and
you will now be logged in.
70
71
If this option is enabled, after you enter your password correctly any new
messages will immediately begin to play.To enable (or if already enabled toggle and disable) this feature:
6
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [5] to Set Auto Play of New Messages.
PERSONAL SERVICES
The Personal Administration Menu is used to set your password and record your
name. Many of these features must be allowed by the System Administrator.
1
■
From the Subscriber Services Menu press [6] for Mailbox Administration.
■
Press [6] to Set Auto Play of Message Information.
9
2
MESSAGE BROADCAST
5
From the Subscriber Services Menu press [6] for Mailbox Administration.
Press [9] for Broadcast Messages.
This option will only be available if your mailbox has been assigned
Subscriber Administration privileges.
Place a Direct Call
Allows you to place a direct call out of the voicemail from anywhere.You may
either dial the number or dial a single digit 1-5 that corresponds to a stored
number (See Personal Services, 2 - Stored Numbers). This feature must be
authorized by the System Administrator and can be limited or opened to
internal, local, and long distance calls.
If you have been designated as a Subscriber Administrator, you may send a
message to ALL mailboxes in the system.
■
Schedule Availability
Allows you to enter a weekly availability schedule for use with Night Personal
Greeting and the Auto Night Intercept feature. Follow the spoken directions
to enter the days of the week and times you are generally available to talk to
your callers. All other times you will be considered unavailable.
This option will only be available if it has been allowed by the System
Administrator.
■
Stored Numbers
Allows you to enter up to 9 stored phone numbers. The first five of these are
used in the 'Find Me' feature, but any of them (1-9) can be easily dialed using
only one digit followed by the pound key, to be used by many other features
from within your subscriber space. (ie: “Follow Me, “Message Alert”, “Pager
Alert”, and “Direct Call”).
3
Broadcast to All Mailboxes
Workload Management
Allows you to access to all reminders, both Active and Pending. If authorized
you can group your reminders as Commitments, Follow-Ups or Tasks for better organization. The system will flag each reminder as Active or Pending
(pending means scheduled for future delivery).
Auto Play Message Information
If this option is enabled, the date, time and sender’s name will be played automatically before each message. If this is disabled, the information must be
requested manually by pressing ‘00’. To enable (or if already enabled toggle
and disable) this feature:
CS Keyset
Auto Play New Messages
#
of Contents
5
ome Page
This useful feature will allow you to cancel any messages that have NOT yet
been picked up by the recipient.
7
Personal Administration
This area is used during the initial set up of your Subscriber Settings (see next
section).
72
73
2
Setting your Password
■
From the Subscriber Services Menu press [#][7][1].
■
The current password will be played and you will have the chance to
change it.
Recording your Name
Use this option to record your name. Your recorded name is played in several
different situations. It is important to record your name for proper operation
of the voicemail system.
■
From the Subscriber Services Menu press [#][7][2].
■
The current name will be played and you will have the chance to change
it.
Note: It is possible that if you do not record your name and/or enter your
Directory Name (described below), you will not be included in the Dial by
Name Directory.
3
Entering your Directory Name
Use this option to enter your Directory Name.Your Directory Name is used by
callers to find you if they do not know your extension number.
■
From the Subscriber Services Menu press [#][7][3].
■
The current Directory Name will be played as a string of digits that are
equal to your name spelled out on your telephone keypad. Follow the
instructions to enter a new name.You will be prompted to enter your last
name and then your first name.
This must be done in order for the directory feature to work correctly.
Note: It is possible that if you do not record your name (described above)
and/or enter your Directory Name, you will not be included in the Dial by
Name Directory.
4
The following options are available if you have a display keyset.They require setup
by the System Administrator.
Message Waiting Lights
When new messages are left in your mailbox, the voicemail message light on your
keyset will flash. Press this flashing key [VMMSG] and follow the prompts to
retrieve messages.This key may be pressed at any time to log into your Subscriber
Main Menu.
Answer Machine Emulation
If you have an Answer Machine Emulation key programmed on your keyset, you
can use it to monitor calls going to your voicemail, and optionally answer them.
The operation of this feature is similar to screening a call on a home answering
machine.
Your keyset must be set to forward on no answer to voicemail. After ringing your
station the caller will be connected to your voicemail and hear your personal
greeting before leaving a message. During this time you will be monitoring the
connection between the caller and your voicemail box. At this time you will only
be monitoring the call, you can not talk to the other party until you answer. You
may pick up the call at any time or ignore it.
To activate this feature press the AME button. The associated indicator will be lit
steady. Press again to turn off. If this key is pressed while a station is ringing (during forward no answer), the feature will be turned on for the current call only.
While the caller is leaving a message or ringing you may:
■
Press [#] to immediately put the caller in your voice mailbox and monitor it.
■
Press [!] to immediately disconnect your station. The caller continues to
leave a message normally.
■
Pick up the handset and monitor privately.
■
Press ANS / RLS to answer the call (using the handset or speaker).
Extended Prompting
Use this option to drastically reduce the number of prompts played in the
subscriber interface (mailbox prompts). Change this setting only if you are
very familiar with the user operation of the voicemail.
74
KEYSET USER FEATURES
75
CS Keyset
This menu allows you to make changes to basic setup settings, that are rarely
changed. Use these when you initially set up your personal Subscriber settings.
You probably will not need to change them after that.
1
of Contents
ome Page
Note: Remember if you know what digits to press, you can enter them at any
time you do not have to wait to be prompted. This feature can be toggled
on/off at anytime. Also if it is off you will be prompted within each subscriber
menu to press zero for more options. This enables you to still be able to find
out what to do if you were to get lost and extended prompting was disabled.
PERSONAL ADMINISTRATION SETTINGS
Calling
If the password option is turned on, while a message is being left, press the flashing AME indicator and enter your station password (not your voicemail password). You will then hear the message being left.
Call Record
If you have a call record button assigned to your phone, you may press it at any
time, to record the conversation in progress. If you have a display keyset, you will
also have the soft key options to pause and time the message.
CS Keyset
If your keyset has AME PASSWORD (MMC 110) set to YES, you must enter your
station password to listen to messages being left. This will prevent unauthorized
people from listening to messages being left for you.
of Contents
SHORTCUTS
ome Page
AME Password
Calling a station that is busy or does not answer you can press [#] to immediately
send the call to the called parties mailbox.
Call Divert to Voicemail
While receiving an incoming (ringing) call, dial [!] to immediately send the caller
to your personal voicemail box. This will override the call forward no answer setting.
Direct Messaging
[#] + DSS To make it easy to leave messages for others in your office without having to dial their extension number first, keyset users may simply dial [#] plus a
mailbox (extension) number and leave a message directly. If you dial a busy extension press [#] to connect directly with the mailbox.
Self Memo (Reminder)
Pressing [##] will leave a message in your own mailbox. This is useful to remind
yourself of things to do now or in the future. Messages can be sent with future
delivery so you can have the system call you when items become due.
INTERACTIVE DISPLAYS
Display keyset users have the added advantage of using the soft keys and displays
to play, save, delete, reply, call, forward, rewind, pause, fast forward, change the volume, get message information, or help.
Viewing Mailbox Contents
If you have new messages, in addition to the Terminal Status Indicator (TSI) you
will be able to use the keyset displays and soft keys to communicate with the
voicemail.
E-MAIL GATEWAY (EMG)
The E-Mail Gateway feature integrates your voicemail box with your email client.
No matter what email client software you are using or where you use it, you can
send voicemail messages and fax mail messages to your E-Mail inbox.
There are two parts to the E-Mail Gateway; E-Message Delivery and E-Message
Notification.
76
77
•
•
As a subscriber you can use either E-Message Delivery and/or E-Message
Notification.
As a subscriber you can have multiple e-mail addresses. (a maximum of
5 valid email addresses).
E-Message Notification can be set to one e-mail address while E-Message
Delivery is set to different e-mail address.
Functionality
•
•
•
With either type of EMG, when Caller ID (CID) is provided, the callers telephone number will appear in the subject field of the email along with the
date and time stamp of when the voice message was originally recorded in
your Voicemail Box.
If the caller is also a subscriber on the system and the E-Mail Gateway is set
up with a valid "Reply To" address, the Subscriber's name will also appear in
the "From" field. Otherwise, the "From" field will display the name of the
Samsung voicemail system sending the message.
Client will use their PC's Multi-Media kit (equipped with either speakers
and/or a headset) to listen to messages delivered to their e-mail Inbox.
IMPORTANT NOTE: If the PC/Laptop/PDA/Smart Phone/etc… is not
equipped with hardware and software capable of playing a '.WAV' file then
the E-Mail Gateway will not work for them until they add some method to
listen to '.WAV' files delivered to their Inbox.
The same applies to Fax Mail messages, if the device the subscriber is using
does not support the viewing of '.TIFF' files, then the E-Mail Gateway for
Fax Mail will not work for them until they add some method to view .tiff
files delivered to their inbox.
•
No Synchronization of messages is performed between the Voicemail Box
and the E-mail Inbox.
-
-
78
However, the Voicemail Administrator can adjust parameters per subscriber or group of subscribers that decide how, when, or if to delete the
original voice message after it is sent to the E-Mail Server.
When full synchronization of messages between Voicemail Box and E-mail
Inbox is required, ask your Samsung representative about the OfficeServ IPUMS. This is an Internet Protocol based fully synchronized Unified Messaging
System.
Benefits
•
•
•
•
•
•
•
•
•
•
Store and Archive Voice and Fax Mail Messages in visible folders.
Voice and Fax Mail Messages can now easily be dragged and dropped into
folders the same way e-mail messages are organized and saved.
Voice and Fax Mail Messages are now essentially the same as any other e-mail
message.
Backups and Message Archives can be made when they are made for all other
types of e-mail messages.
Add text notes and comments to use for reference later.
Some (if not all) e-mail clients will allow you to edit the body of the e-mail to
add comments.
Some will allow you to edit the subject field to help you find a particular message quickly in a large archive of messages.
Call Back Numbers and Date & Time Stamp are easily displayed in the Subject
field.
Easily forward Voice messages received, to others even if they are not a
Voicemail Subscriber on your system.
No EMG System or Client Software to load on your Local PC or Network
Servers.
Therefore compatible with most:
-
E-Mail providers and E-Mail Clients
-
PCs, Laptops, PDA, and/or Smartphones
NOTE: If you are not sure you have this functionality on your system and
you would like to use it, please contact your on Site system administrator
to see if it is available.
Messages listened to, forwarded, deleted, and/or saved within an e-mail
inbox will NOT effect the status of that same new message in the
Voicemail or the MWI (Message Waiting Indicator) associated with that
message on the phone.
Also messages listened to in the Voicemail, from a phone, will not change
the Unread/Read status of the same message in an e-mail inbox.
79
CS Keyset
•
•
of Contents
2. E-MESSAGE NOTIFICATION: You will receive an e-mail, with NO attachments,
notifying you that you have a voice and/or fax mail message in your Voicemail
Box.
-
ome Page
1. E-MESSAGE DELIVERY: Voicemail messages (.wav) and/or fax mail messages
(.tiff ) are "delivered" to your Inbox with the appropriate attached file.
PERSONAL SPEED DIAL NUMBERS
CODE
NAME
TELEPHONE NUMBER
CODE
NAME
TELEPHONE NUMBER
00
_________________________
_________________________
25
_________________________
_________________________
01
_________________________
_________________________
26
_________________________
_________________________
02
_________________________
_________________________
27
_________________________
_________________________
03
_________________________
_________________________
28
_________________________
_________________________
04
_________________________
_________________________
29
_________________________
_________________________
05
_________________________
_________________________
30
_________________________
_________________________
06
_________________________
_________________________
31
_________________________
_________________________
07
_________________________
_________________________
32
_________________________
_________________________
08
_________________________
_________________________
33
_________________________
_________________________
09
_________________________
_________________________
34
_________________________
_________________________
10
_________________________
_________________________
35
_________________________
_________________________
11
_________________________
_________________________
36
_________________________
_________________________
12
_________________________
_________________________
37
_________________________
_________________________
13
_________________________
_________________________
38
_________________________
_________________________
14
_________________________
_________________________
39
_________________________
_________________________
15
_________________________
_________________________
40
_________________________
_________________________
16
_________________________
_________________________
41
_________________________
_________________________
17
_________________________
_________________________
42
_________________________
_________________________
18
_________________________
_________________________
43
_________________________
_________________________
19
_________________________
_________________________
44
_________________________
_________________________
20
_________________________
_________________________
45
_________________________
_________________________
21
_________________________
_________________________
46
_________________________
_________________________
22
_________________________
_________________________
47
_________________________
_________________________
23
_________________________
_________________________
48
_________________________
_________________________
24
_________________________
_________________________
49
_________________________
_________________________
80
CS Keyset
of Contents
ome Page
PERSONAL SPEED DIAL NUMBERS
81
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement