C. All fiber optic modules shall be supplied from... single manufacturer. A. Model Number Descriptions: Reference Table SECTION 00000

C.  All fiber optic modules shall be supplied from... single manufacturer. A.  Model Number Descriptions: Reference Table SECTION 00000
SECTION 00000
R3 SERIES – CARD CAGE
ENGINEERING SPECIFICATIONS
C. All fiber optic modules shall be supplied from a
single manufacturer.
2.02 MANUFACTURED UNITS
A. Model Number Descriptions: Reference Table
A: Product Number Descriptions
B. Model Compatibility Chart: Reference Table B:
Product Compatibility Chart
2.03 GENERAL SPECIFICATIONS
A. The Card Cage system for holding fiber optic
rack equipment shall be an IFS R3 system. The
module shall provide a power status indicating
LED for monitoring proper system operation.
The module shall have an MTBF of >100,000
hours and operate in an environment of –40˚ C to
+74˚ C and relative humidity between 0% to
95% (non-condensing). The module shall be UL
and ULC listed and CE marked. The circuit
board shall be UL 94 flame rated and meet all
PCI standards. All PC boards shall be designated
with part number, PC board number and show
appropriate revision number. Housing shall be of
all metal construction. All LED indicators and
both electrical and mechanical connections shall
be identified with silk-screened labels. The
module shall have a lifetime warranty to reduce
system life cycle cost in an event of a module
failure.
2.04 STATUS INDICATORS
A. Power: On/Red – Off/Off
2.05 ELECTRICAL SPECIFICATIONS
A. Current Protection: Automatic re-settable solidstate current limiters
B. Voltage Regulation: Solid-state, Independent on
each board
C. Circuit Board: UL 94 flame rated and meets all
PCI standards.
2.06 MECHANICAL SPECIFICATIONS
A. Finish: Module shall be constructed of a metal
enclosure. Rack shall be constructed of anodized
aluminum.
B. Weight: <8.0 lbs./3.6kg
2.07 ENVIRONMENTAL SPECIFICATIONS
A. MTBF: >100,000 Hours
B. Operating Temp: –40˚ C to +74˚ C
C. Storage Temp: -40˚ C to +85˚ C
2.08 REGULATORY AGENCIES/APPROVALS
AND LISTINGS
A. Underwriters Laboratory (UL) Listing Number:
I.T.E. 6D16
B. Underwriters Laboratory Canada (ULC) Listing
Number: I.T.E. 6D16
C. UL 94-flame rated PCB board: 94VO
D.
2.09 ACCESSORIES
A. Blank Panels: IFS Model Number R3-BP shall
be available to cover unused rack slots.
PART 3 - EXECUTION
3.01 EXAMINATION
A. Inspect modules before installation.
PART 1 - GENERAL
1.01 SUMMARY
A. CARD CAGE
1.02 SECTION INCLUDES
A. R3 Series Card Cage
1.03 REFERENCES
A. Underwriters Laboratory (UL)
B. Underwriters Laboratory Canada (ULC)
C. European Union Compliance (CE)
1.04 SYSTEM DESCRIPTION
A. Performance Requirements: Provide a Card Cage
system that holds fiber optic rack equipment.
1.05 SUBMITTALS
A. Product Data: Manufacturer’s printed product
data sheet for each type of Transmitter/Receiver
specified.
B. Detail Drawings: Electrical and optical connect
drawings. Product mounting template.
C. Manufacturer’s Installation and Operating
Manual: Printed installation and operating
information for each type of
Transmitter/Receiver specified.
D. Warranty: Manufacturer’s Printed Warranty
1.06 DELIVERY, STORAGE AND HANDLING
A. Deliver materials in unopened factory packaging
with Manufacturer’s bar coding to the job site.
B. Inspect product upon delivery to assure that
specified products have been received.
C. Store in original packaging in a climate
controlled environment. Storage Temperature
not to exceed: -40˚ C to +85˚ C
1.07 PROJECT/SITE CONDITIONS
A. Temperature Requirements: Products shall
operate in an environment with an ambient
temperature range of –40˚ C to +74˚ C without
the assistance of fan-forced cooling.
B. Humidity Requirements: Products shall operate
in an environment with relative humidity of 0%
to 95% (non-condensing). If product is installed
in condensation conditions, unit shall have
conformal coating applied to the printed circuit
board.
1.08 WARRANTY
A. Standard International Fiber Systems
Comprehensive Lifetime Warranty: IFS
warrants the product to be free of factory defects
under manufacture’s Lifetime Warranty as
submitted under article 1.05 (E)
PART 2 - PRODUCTS
2.01 MANUFACTURER
A. Acceptable Manufacturer: International Fiber
Systems, Inc.; 16 Commerce Road, Newtown,
CT 06470 USA; Telephone: 203-426-1180; Fax
203-426-3326; Email: [email protected]; Internet:
www.ifs.com
B. Substitutions: Not Permitted
Project name/project number/date
00000 - 1
(Optional information, e.g., owner, A/E)
Section Title
B. Modules shall be free of any cosmetic defects or
damage.
C. Shipping box shall include the module, power
supply and operations manual.
3.02 PREPARATION
A. Rack Mount Module (19” Rack)
1. Ensure the card cage is installed in a
standard EIA 19” (482.6 mm) rack or wall
standoff bracket adequate for the size and
weight of the card cage.
Section Title
3.03 INSTALLATION
A. General: Locate fiber optic modules as indicated
on the approved detail drawings and install
module in compliance with the IFS installation
and operations manual.
3.04 CLEANING
A. Follow all instructions for proper use of solvents
and adhesives used for termination and splicing.
B. At completion of the installation, dispose of all
fiber scraps properly.
00000 - 2
Project name/project number/date
(Optional information, e.g., owner, A/E)
END OF SECTION
Project name/project number/date
(Optional information, e.g., owner, A/E)
00000 - 3
Section Title
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement