Model 702-17 and 802-19 Manure Spreader Truck

Model 702-17 and 802-19 Manure Spreader Truck
702-17 & 802-19
MANURE SPREADER
TRUCK UNIT
OPERATOR’S MANUAL , MAINTENANCE
AND REPAIR PARTS
ROTO-MIX LLC
2205 E. Wyatt Earp
PO Box 1724
Dodge City, Kansas 67801
(620) 225-1142
©Roto-Mix LLC 2006
441936 03/2016
Printed in U.S.A.
Page
INTRODUCTION
Congratulations on the purchase of your new
spreader from Roto-Mix. With proper operation and
preventative maintenance it will last for years.
The Guarantee appears in the front of this book
along with the Registration and Inspection
Certificate.
For information on ordering repair parts, refer to the
Repair Parts section at the back of this book.
This SAFETY ALERT SYMBOL indicates
important safety messages in the manual. When you
see this symbol, be alert to the possibility of
PERSONAL INJURY and carefully read the message
that follows.
NEVER OPERATE WITHOUT
ALL COVERS, SHIELDS AND GUARDS IN PLACE.
KEEP HANDS, FEET AND CLOTHING AWAY
FROM MOVING PARTS.
Some covers and guards have been removed for
illustrative/photographic purposes only in this
manual. However, equipment should never be
operated in this condition. Keep all shields in place. If
shield removal becomes necessary for repairs,
replace the shield prior to use.
The serial number plate is located on the drivers side
lower front of the main frame. This number should be
recorded on the Registration and Inspection
Certificate for your reference and for proper
identification of your spreader by Roto-Mix.
You are urged to study this manual and follow the
instructions carefully. Your efforts will be repaid in
better operation and service as well as a savings in
time and repair expense.
Failure to read and understand the machine or the
system could lead to serious injury.
If you do not understand the instructions in this
manual contact either your dealer or Roto-Mix at
Dodge City, Kansas 67801.
This supersedes all previous published instructions.
Page 2
Limited Warranty Statement
ROTO-MIX LLC warrants to the original purchaser all products manufactured by it to be free from defects in material and
workmanship under normal use and service.
ROTO-MIX’s obligation under this warranty is limited to repairing or replacing, as the company may elect, free of charge
and without charge for installation, at the place of business of a dealer or distributor authorized to handle the equipment
covered by this warranty or at a ROTO-MIX plant, any parts that prove, in the company’s judgment, to be defective in
material or workmanship within one (1) year after delivery to the original purchaser, and still owned by the original
purchaser. This warranty shall in no way make ROTO-MIX liable to anyone for personal injuries or damages, loss of time,
or expense of any kind either direct or indirect resulting from part failure or defect. This warranty is subject to acts of God,
fire and existing conditions of supply and demand, or production, or ability or inability to deliver, or for any other valid
reason beyond the reasonable control of ROTO-MIX, to obtain materials, manufactured replacement parts, or make
delivery thereof. No distributor, dealer, agent, or ROTO-MIX employee (other than the CEO or President in writing) is
authorized to extend any other or further express or implied warranty or incur any additional obligation on ROTO-MIX’s
behalf in connection with the sale of this product.
Customer Responsibility
Product Registration - It is a condition of this warranty that the original purchaser must fill out the warranty card
furnished by ROTO-MIX and that it be returned to ROTO-MIX and be recorded in ROTO-MIX’s owner file for this
warranty to be valid. In the event an owner’s card is not on file at the ROTO-MIX office, the warranty period will extend
only from date equipment was picked up or shipped from the ROTO-MIX plant.
Maintenance - It is the customer’s responsibility to maintain their equipment in accordance with the instructions provided
in the Operator’s Manual. ROTO-MIX recommends that you keep records and receipts; you may be asked to prove that
maintenance instructions have been followed.
Operation - It is the customer’s responsibility to operate the equipment only for the purpose for which it was designed and
in accordance with all safety and operational recommendations contained in the Operators Manual. If a defect in
materials or workmanship occurs, it is the customer’s responsibility to cease operating the equipment until authorized
repairs are made. Damage, which occurs from continued operation, may not be covered by this warranty.
What this Warranty Covers
This warranty covers failures caused by defects in materials or workmanship only.
This Warranty does not cover failures caused by:
- Improper operation
- Unauthorized repairs
- Natural calamities
- Use of Non ROTO-MIX parts
- Unauthorized modifications
- Neglected maintenance
- Usage contrary to the intended
purpose of the product
This Warranty does not cover replacement of Wear or Maintenance Items (unless defective) including, but not
limited to.
- Lubricants
- Filters
- Hoses
- Tires
- Augers
- Wipers
- Chains
- Idlers
- Blades
- Belts
This Warranty does not cover:
- Pickup and delivery of the equipment
- Service Calls or Travel Time to and from sites
- Rental of replacement equipment during repair period
- Products that have been declared a total loss and
subsequently salvaged
- Overtime labor charges
Right to Make Changes
ROTO-MIX reserves the right to make any changes to a ROTO-MIX product at any time without incurring any obligation
with respect to any product previously ordered, sold or shipped, with or without notice.
Parts Warranty
ROTO-MIX warranties replacement parts against defects in materials or workmanship for a period of 90 days or the
remainder of the product warranty, whichever is longer. Remedy for defective replacement parts for units that are beyond
the original product warranty, will be limited to replacement of the failed part. Failures that are due to damage, improper
installation, lack of maintenance or improper operation will not be covered.
ROTO-MIX 2205 East Wyatt Earp Blvd., Dodge City, KS 67801 (620) 225-1142 Fax: (620) 225-6370
Page 3
TABLE OF CONTENTS
DESCRIPTION
PAGE NO.
Introduction ................................................................................................................ 2
Warranty .................................................................................................................... 3
Table Of Contents ...................................................................................................... 4
Safety-Spreader ......................................................................................................... 5
Safety Decals ............................................................................................................. 5
Spreader Safety ......................................................................................................... 6
Safety Decal Care ................................................................................................ 8
Principle of Operation ................................................................................................. 9
Pre Operation Check List ........................................................................................... 9
Highway and Transport Operation ............................................................................ 9
Operation .................................................................................................................. 10
Loading ................................................................................................................ 10
Unloading ............................................................................................................ 10
Spread Pattern .................................................................................................... 12
Storage and Cleaning .......................................................................................... 12
Maintenance ............................................................................................................. 13
Lubrication ........................................................................................................... 13
Bearings .............................................................................................................. 13
Drive Chain Planetary Gearbox ........................................................................... 13
Belt Maintenance.................................................................................................. 13
Rear Gate Cylinders ............................................................................................. 13
Hydraulic System ................................................................................................ 14
Adjustments ......................................................................................................... 14
Sliding Gate Scrapers ......................................................................................... 14
Drive Chain Slack (With Belleville Washer Take-up) ........................................... 16
Drive Chain Slack (With Urethane Spring Take-up) ............................................. 16
Rear Gate Scrapers ............................................................................................ 16
Adjust Spread Pattern ......................................................................................... 17
Specifications ............................................................................................................ 18
Dimensions ................................................................................................................ 19
Repair Parts .............................................................................................................. 21
Page 4
SAFETY - SPREADER
A brief definition of signal words that may be used in this manual:
Indicates an imminently hazardous
situation that, if not avoided, will result in death or
serious injury.
Indicates a potentially hazardous
situation that, if not avoided could result in death or
serious injury, and includes hazards that are
exposed when guards are removed.
Indicates a potentially hazardous
situation that, if not avoided may result in minor or
moderate injury.
A (Both Sides)
D (Both Sides)
B (Both Sides)
B,C & D (Front)
NOTE: Complete decal kit part number for 702-17 is 630025, for 802-19 is 630016
Decal B. 440833
Decal A. 440827
Decal C. 440801
Decal D. 441657
READ ALL SIGNS ON THE MACHINE AND IN THIS MANUAL. REPLACE ANY LOST
OR DAMAGED SIGN BY ORDERING THE PART NUMBERS SHOWN ON THE SAFETY DECAL PAGE.
Page 5
SPREADER SAFETY
Do not operate your spreader until you have read this Owner’s Manual, and understand the danger
associated with its operation.
This spreader is comprised of rotating drive shafts and rotating beaters. Any exposure to these spreader
components can result in serious personal injury or death.
Study the safety decal page and understand where the danger points are.
THERE ARE INHERENT HAZARDS ASSOCIATED WITH THE OPERATION OF YOUR SPREADER.
FOR YOUR SAFETY:

Do Not Operate, Service, Inspect Or Otherwise Handle This Equipment Unless You Have Read The
Owner’s Manual And Have Been Properly Trained In Its Intended Usage.

Do Not Attempt To Operate This Equipment Under The Influence Of Drugs Or Alcohol.

Do Not Allow Personnel Other Than The Qualified Operator Near The Machine.

Require All Personnel Who Will Operate This Machinery Or Perform Service, To Read And Understand
The Safe Operating Practices And Safety Precautions In This Manual.

Do Not Operate Until All Shields, Covers And Guards Are In Place.

Do Not Allow Children Or Inexperienced Persons To Operate This Machine.

Keep Hands, Feet And Clothing Away From Power Take-Off Shaft.

Loose Or Floppy Clothing Should Not Be Worn By The Operator. Wear Close Fitting Clothing.

Stop The Engine And Be Sure PTO Drive line Is Stopped Before Making Adjustments, Connections, Or
Cleaning Out PTO Driven Equipment.

Do Not Climb On Or Enter Machine While In Operation.

Do Not Allow Riders On The Spreader.

Rotating Parts Can Crush Or Dismember Causing Personal Injury Or Death.

Rotating Parts Can Entangle Or Strike People, Resulting In Personal Injury Or Death.

Operate The Spreader From The Operator’s Seat Only.

Clear The Area Before Equipment Start Up.

Do Not Go Near The Spreader Beaters While Machine Is Operating.
FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Page 6

Stay Clear Of Rotating Drive lines.

Entanglement In Rotating Drive line Can Cause Serious Injury Or Death.

Do Not Exceed Load Capacity Of The Spreader (See Specifications).

Do Not Operate On Steep Slopes As Overturn May Result. Operate Up And Down (Not Across)
Intermediate Slopes. Avoid Sudden Starts And Stops. Pick The Most Level Possible Route When
Transporting Across Fields. Avoid The Edges Of Ditches Or Gullies And Steep Hillsides.

Use Caution When Traveling Over Uneven Terrain And When Approaching Stops.

Avoid Overhead Wires Or Other Obstacles. Contact With Overhead Lines Could Cause Serious Injury or
Death.

As A Precaution, Always Recheck The Hardware On Spreader Following Every 100 Hours Of Operation.
Correct All Problems. Follow The Maintenance Safety Procedures.
THERE ARE ADDITIONAL HAZARDS ASSOCIATED WITH THE SERVICE AND MAINTENANCE OF
YOUR SPREADER.
FOR YOUR SAFETY:

Always Wear Eye Protection When Servicing Spreader.

Disengage Power Take-Off And Remove Keys From Truck Before Servicing Spreader.

Do Not Attempt To Clean, Oil Or Adjust Spreader While It Is In Motion.

Stop The Engine And Be Sure Spreader Is Stopped Before Making Adjustments, Connections, Or
Cleaning Out Equipment.

Make Sure There Is Plenty Of Ventilation. Never Operate The Engine Of The Vehicle In A Closed
Building. The Exhaust Fumes May Cause Asphyxiation.

Before Working On The Spreader, Stop The Vehicle, Set The Brakes, Disengage The PTO And All
Power Drives, Shut Off The Engine And Remove The Ignition Keys.

Inspect When First Delivered And Regularly Thereafter; That All Connections And Bolts Are Tight And
Secure Before Operating.

Retighten All Wheel Bolts After The First Hour Of Operation. Check Periodically Thereafter.

Maintain Proper Tire Air Pressure At All Times.

Be Certain All Moving Parts On Attachments Have Come To A Complete Stop Before Attempting To
Perform Maintenance.

Before Entering Mixing Chamber Or Servicing Spreader, Disconnect Main Power Source And Lock The
Disconnect Device In Off Position To Prevent Accidental Start-Up.
FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Page 7

Do Not Work Under A Spreader Without Supporting With Suitable Support Stands. Always Use A Safety
Support And Block The Wheels. Never Use A Jack To Support The Machine.

Do Not Work Under A Spreader Without Blocking The Wheels To Prevent Rolling.

A Fire Extinguisher And First Aid Kit Should Be Kept Readily Accessible While Performing Maintenance
On This Spreader.

Escaping Hydraulic Fluid Under Pressure Can Penetrate The Skin Causing Serious Injury Or Death.

Avoid Hydraulic Hazard By Relieving Hydraulic Pressure Before Disconnecting Hydraulic Or Other
Lines.

Tighten All Connections Before Applying Pressure.

Search For Hydraulic Leaks With A Piece Of Cardboard. Protect Hands And Body From High Pressure
Fluids. Never Use Your Hands To Locate Hydraulic Leaks On Attachments.

Replace All Shields And Guards After Servicing And Before Moving.

Never Replace Hex Bolts With Less Than Grade Five (5) Bolts Unless Otherwise Specified.
REMEMBER:
Your best assurance against accidents is a careful and responsible operator. If there is any portion of this
manual or function you do not understand, contact your dealer or the ROTO-MIX plant.
Safety Decal Care
1. Keep safety decals and signs clean and legible at all times.
2. Replace safety decals and signs that are missing or have become illegible.
3. Replaced parts that displayed a safety sign should also display the current sign.
4. Safety decals or signs are available from your dealer or the ROTO-MIX manufacturing plant.
5. How to Install Safety Decals:
A. Be sure that the installation area is clean and dry.
B. Decide on the exact position before you remove the backing paper.
C. Remove the smallest portion of the split backing paper.
D. Align the decal over the specified area and carefully press the small portion with the exposed
sticky backing in place.
E. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in
place.
F. Small air pockets can be pierced with a pin and smoothed out using the piece of decal backing
paper.
FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Page 8
PRINCIPLE OF OPERATION
Two vertical spinning beaters at the rear of the spreader expel manure in a uniform spread pattern. Each
beater is driven by a hydraulic motor. A PTO driven hydraulic power supply on the spreader provides power
to the beaters. The hydraulic pump is two stage thereby supplying independent power to each beater motor.
A wide heavy duty belt covers the box floor. At the front of the spreader, this belt is attached to a sliding
gate. At the rear, this belt goes around a belt idler pulley and on the lower side is connected to a drive
chain. At the front of the spreader, this chain is driven by a hydraulic motor driving a planetary gear box
and sprocket that is powered by the truck hydraulic system. Driving the belt toward the rear of the
spreader pulls the sliding gate rearward to move the load toward the beaters. A manually adjustable flow
control in the drive chain motor circuit regulates the speed the gate moves.
An end gate at the rear of the spreader is raised and lowered by two hydraulic cylinders, powered by the
truck hydraulic system. This gate must be lowered during loading to prevent packing of the material into
the beaters and to help prevent leakage during transport.
PRE OPERATION CHECKLIST
1. Carefully study and understand this manual.
2. Do not wear loose-fitting clothing, which may catch in moving parts.
3. Always wear protective clothing and substantial shoes.
4. Keep wheel lug nuts or bolts tightened to specified torque.
5. Give the unit a visual inspection for any loose bolts, worn parts or cracked welds, and make necessary
repairs. Follow the maintenance safety instructions included in this manual.
6. Check to see that no obstructions are present in the spreader prior to start up.
7. Be sure that there are no tools lying on or in the spreader.
8. Do not use the unit until you are sure that the area is clear, especially children and animals.
9. The ball valve in the suction line must be open prior to engaging PTO (handle parallel with valve
housing).
10. Because it is possible that this spreader may be used in dry areas or the presence of combustibles,
special precautions should be taken to prevent fires and fire fighting equipment should be readily
available.
11. Don’t hurry the learning process or take the unit for granted. Ease into it and become familiar with your
new spreader.
12. Practice operation of your spreader and its attachments. Completely familiarize yourself and other
operators with its operation before using.
13. Do not allow anyone to ride on the inside or the outside of the spreader unit at any time.
HIGHWAY AND TRANSPORT OPERATION
1. Adopt safe driving practices.
2. Always drive at a safe speed relative to local conditions and ensure that your speed is low enough for an
emergency stop to be safe and secure. Keep speed to a minimum.
3. Reduce speed prior to turns to avoid the risk of overturning.
Page 9
4. Avoid sudden uphill turns on steep slopes.
5. Do not drink and drive.
6. Comply with state and local laws governing highway safety.
7. Plan your route to avoid heavy traffic.
8. Be a safe courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges,
intersections, etc.
9. Be observant of bridge loading ratings. Do not cross bridges rated lower than the gross weight at which
you are operating.
10. Watch for obstructions overhead and to the side while transporting.
11. Make allowances for increased length and weight of the spreader when making turns, stopping the unit,
etc.
OPERATION
LOADING
Park the spreader for loading. Put the truck in PARK or NEUTRAL and apply the parking brake.
Make sure the sliding front gate is all the way to the front of the spreader and close the hydraulic rear gate
before loading.
It is unlawful to allow any manure spillage to occur on public roadways. Be sure rear gate is fully closed and
sliding gate scrapers are adjusted so no liquid leakage occurs. Do not heap load such that manure is allowed
to fall off spreader during transporting on roadways.
Load the spreader. The moisture content will determine how full it can be loaded. See SPECIFICATIONS for
capacity. Solid manure can generally be loaded level to slightly heaped. High moisture slurries are heavier
and loading may be limited.
UNLOADING - RUNNING YOUR SPREADER
1. Start the truck, and engage the PTO
2.
PRESS SYSTEM ON
TO START
Press the SYSTEM ON/OFF button.
The SYSTEM ON light will turn on.
3.
PRESS BEATER ON
TO START BEATERS
Press the BEATER ON/OFF button.
The BEATER ON light will turn on and the beaters will
start turning.
Page 10
4.
PRESS GATE UP
TO OPEN GATE
Press the GATE UP/DN button.
A beeper will sound as the rear gate rises.
When the gate is up, the beeper will stop and the GATE UP light will turn on.
5.
OK TO SPREAD
PRESS FLR BCK PB
Press the FLOOR BACK button.
The floor will start moving towards the beaters. The screen will read:
After a few seconds, it will change:
Beater RPM
Beater Pressure
R:
P:
SPREADING
PRESS FLR BCK PB
0
0
FLR
5828 5828 25%
A. Adjust the speed of the floor by pressing the FLOOR INCR (+) and the
FLOOR DECR (-) buttons. The FLR percent value on the screen will change:
B. Stop the floor by pressing the STOP/ALARM CLEAR button. To restart the
floor motion press the FLOOR BACK button.
C. When the floor reaches the back limit, an alarm notification will appear on the
screen and the control unit will start beeping:
R:
P:
0
0
FLR
5828 5828 26%
OK TO SPREAD
PRESS FLR BCK PB
**FAULT DETECT**
FLOOR STOPPED!
To clear the alarm press the STOP/ALARM CLEAR button.
6.
OK TO SPREAD
PRESS FLR BCK PB
Press the FLOOR FWD button.
When the button is pressed the screen will read:
FLOOR FORWARD
FLR SPEED = 100%
The floor will come towards the truck cab. The beaters will ramp down to a halt
light will turn off. When the floor reaches the front limit, the rear gate will lower.
The screen will read:
PRESS BEATER ON
TO START BEATERS
7. Repeat the cycle of steps 3 to 6 as needed. When you are done:
Press the SYSTEM ON/OFF button.
Shut down the PTO and the truck.
Page 11
and the BEATER ON
NOTE: At the end of the day, clean the belt by running it forward and back several times. This will help
smooth out any larger clumps of material left on the belt top or on the inside of the belt, which if left on the
belt could damage the belt and roller the next time the spreader is in operation, especially during freezing
weather.
The “wings” may be adjusted to change the width of the spread pattern. Normally a “mid position” setting is a
good place to start. (Note “wings” may be removed if desired for close quarter operation in pens”.
If unloading semi-liquid material the rear gate may be raised in incremental amounts to control the rate of
discharge.
NOTE!
BEFORE MOVING THE FRONT GATE, THE REAR GATE MUST BE RAISED
COMPLETELY TO PREVENT DAMAGE TO THE FRONT GATE.
Unit is equipped with a beater stall warning horn. The intensity of the horn can be adjusted by turning a
“muffler” on the face of the horn. Intermittent sounding of the horn during operation is normal. If the horn
sounds continuously the belt speed dial should be reset to a lower number.
Vary belt speed with the consistency of the material being spread. A lower setting might be desired for sticky
or frozen material. A higher setting for dry and light material.
Spread Pattern
The spread pattern is affected by the speed of the rotating beaters. The two beater hydraulic motors are
powered independently by a two stage hydraulic pump on the spreader. This pump is powered by the truck
PTO. The spreader is designed to give a uniform spread pattern when the truck engine is operated at 1500 2100 RPM for typical materials. Adjustment of the beater speed and spread pattern is regulated by the
engine speed.
STORAGE AND CLEANING
TURN OFF ALL POWER DURING CLEANING AND INSPECTION. DO NOT USE POWER TO MOVE ANY
COMPONENTS OR TO DISCHARGE MATERIAL WHILE CLEANING OR INSPECTING.
SET PARKING BRAKE & REMOVE IGNITION KEY BEFORE CLEANING, ADJUSTING,
LUBRICATING, OR SERVICING THIS MACHINE.
1. The spreader must be thoroughly cleaned for extended storage. Manure is acidic and will damage paint
and cause rusting of metal components.
2. Allow the spreader to completely unload.
3. Return the sliding gate to the front of the spreader.
4. To clean the spreader, raise the rear gate.
5. Hose off manure from the outside and inside of the spreader. Completely clean manure from moving
mechanisms such as the beaters, belt pulley, sliding gate, chain drive and rear gate. Remove
accumulation in confined areas or pockets that trap manure.
6. Avoid directing high pressure spray directly on bearings, seals and flow control valve.
7. Keep high pressure spray moving on painted surfaces. Sustained spray on cracks or scratches in paint
can result in paint peeling.
8. Allow machine to dry.
9. Lower rear gate completely down before storing spreader.
10. Inspect the spreader for loose connections, damaged hydraulic hoses or connections and for other
damaged components. Repair if necessary so the spreader is ready for future operation.
Page 12
MAINTENANCE
APPLY THE PARKING BRAKE,
TURN OFF ENGINE AND REMOVE IGNITION KEY
BEFORE CLEANING, ADJUSTING, LUBRICATING
OR SERVICING THIS MACHINE.
FILL PLUG
ON TOP
CHECK LEVEL PLUG
READ THE FOLLOWING BEFORE
WELDING ON THIS MACHINE
1. When welding on your spreader, do not allow the
current to flow through the ball bearings or the
roller chains. Ground directly to the item being
welded.
2. The alternator battery & spreader controller on
the truck should always be disconnected before
welding on the spreader.
LUBRICATION
PLANETARY GEARBOX
Bearings
(See figure 1)
HYDRAULIC MOTOR
Grease 2 upper beater bearings and 2 wing pulley
bearings every 10 hours of operation with 2 pumps of
grease.
FIGURE 2. PLANETARY GEARBOX
PLANETARY GEARBOX
(See figure 2)
Oil Specification: Mobil Delvac Synthetic Gear Oil
75W-90. There is a check plug half way up on the
gearbox. Maintain the oil level to this check plug. Fill
plug is located on the top of the gearbox.
BELT MAINTENANCE
Clean the belt roller when needed, so that material
does not build up inside roller.
WINGED PULLEY
BEARING
(ONE EACH SIDE)
UPPER BEATER
BEATING
GREASE ZERKS
(ONE EACH SIDE)
FIGURE 1. BEARING LUBRICATION
Clean bottom side of belt below frame so that
material does not pack into roller and damage belt
and roller. This maintenance procedure is especially
important during freezing weather.
REAR GATE LIFT CYLINDERS
Clean out around rear gate lift cylinders daily.
Material that is left around cylinders can become
solid and damage cylinders when they are activated.
Page 13
HYDRAULIC SYSTEM
(See figure 3)
RESERVOIR
FILLER CAP
WITH SCREEN
1. Oil Specification: Mobil SHC 524 Synthetic
Hydraulic Oil .
2. Capacity: 60 gallon.
3. Maximum allowable operating temperature
240°F.
4. Check the oil level in the reservoir daily. It
should be maintained 1” from the top of the
sight gauge when cold.
5. Oil is added through a filter screen inside the
filler neck. Before filling, remove the screen,
inspect, clean and replace if required. After
replacing screen add oil to proper level.
BALL VALVE
SIGHT &
TEMP GAUGE
SUCTION SCREEN
6. Carefully clean dirt from the return filter head
and element. Replace the filter element every
500 hrs of operation.
7. Drain reservoir and refill with new oil every
2000 hrs or annually, whichever occurs first. If
the oil becomes contaminated and appears
milky colored, replace immediately.
8. Every 100 hrs of operation, inspect all hydraulic
hoses, hose connections, pump seals and
motor seals for leakage. Tighten loose
connections and replace damaged
components.
9. A ball valve is provided at the bottom of the
reservoir where the suction hose is connected.
Turn this valve off to service hydraulic
components. This prevents draining of the
reservoir, however it is necessary to catch the
oil that drains from disconnected hoses into a
suitable container for proper disposal. Always
check and refill the reservoir as required when
servicing is completed.
RETURN FILTER
ELEMENTS
FIGURE 3. HYDRAULIC RESERVOIR
REAR GATE
EXPLODED VIEW
Rear Gate Flashing
(See figure 4)
1. Swinging gate flashing strips are clamped to
both vertical ends of the rear gate frame. These
strips must bear against the vertical box sides
to minimize leakage.
2. To adjust, loosen the six 3/8" carriage bolts
clamping the flashing.
3. Move the flashing strips so they contact against
the box wall and retighten bolts.
CLAMP STRIP
FLASHING STRIP
FIGURE 4. REAR GATE FLASHING
Page 14
Sliding Gate Drive Chain Slack (With
Bellville Spring Washer Take-up)
(See figure 5)
INNER & OUTER 1” NUTS
& SPRING STOP WASHER
THREADED
ADJUSTER ROD
1. To adjust the floor drive chain, run
the sliding gate all the way to the
rear of the spreader until it stops.
2. Remove the front panel of the
sliding gate.
3. A threaded adjuster rod is provided
where the drive chain attaches to
the sliding gate. It is factory preset,
but may require adjustment with
usage.
5-1/4”
4. Loosen the two 1” hex nuts on the
end of the threaded rod. Tighten the
inner nut until the forty eight
Belleville washers are almost fully
compressed (approximately 5-1/4”).
Tighten the outer nut against the
inner to lock the adjustment.
5. Replace the front panel.
NOTE: The Belleville washers are
assembled in “tail to tail” pairs and
stacked per figure 5 detail.
Sliding Gate Drive Chain Slack (With
Urethane Spring Take-up)
PROPER WASHER
STACKING DETAIL
FIGURE 5.
BELLVILLE SPRING WASHER STACK ADJUSTER
DRIVE CHAIN
THREADED ADJUSTER ROD
(See figure 6)
1. To adjust the floor drive chain, run
the sliding gate all the way to the
rear of the spreader until it stops.
2. Remove the front panel of the
sliding gate.
3. A threaded adjuster rod is
provided where the drive chain
attaches to the sliding gate. It is
factory preset, but may require
adjustment with usage.
4. Loosen the two 1” hex nuts on the
end of the threaded rod. Tighten
the inner nut until the urethane
springs are almost fully
compressed (5/8” from end of
canister). Tighten the outer nut
against the inner to lock the
adjustment.
5. Replace the front panel.
URETHANE
SPRING CANISTER
INNER & OUTER 1” NUTS
& SPRING STOP WASHER
FIGURE 6.
URETHANE SPRING CHAIN ADJUSTER
Page 15
ADJUSTMENTS
Sliding Gate Scrapers
(See figure 7)
1. A high density polyethylene
scraper bar is clamped to the
vertical edges of the sliding
gate. These scrapers must
contact the vertical box walls to
clean material.
SCRAPER
CLAMP
SCRAPER
2. To adjust, loosen the seven 3/8
carriage bolts clamping the
scraper.
3. Move the scrapers so they
contact against the box wall
and retighten bolts.
FIGURE 7. ADJUST SLIDING GATE SCRAPERS
ADJUSTMENTS
Fastening Floor Belt to Slide
Gate
(See figure 8)
1. If the floor belt is ever removed
from the slide gate the bolts
and nuts that fastens the floor
belt to the slide gate must be
torque to 70 FT.LBS. If the nuts
need to be replaced they must
be a 7/16”-20 Grade 8 nut in
order to be torque to 80 ft lbs.
TORQUE TO 70 FT.LBS
FIGURE 8. FASTENING THE BELT TO THE SLIDE GATE
Page 16
Adjust Spread Pattern ( THIS IS ONLY AVAILABLE AS AN OPTION)
(See figure 9)
The deflectors at the rear of the spreader can be set for wide spreading or they can be hinged inward to
spread straight behind the spreader.
ADJUST HERE (BOTH SIDES)
FIGURE 9. ADJUST SPREAD PATTERN
Page 17
SPECIFICATIONS
Roto-Spread
702-17 Truck
802-19 Truck
Capacity (Heaped)
702 Cubic Foot
802 Cubic Foot
Struck Level
510 Cubic Foot
3,815 Gallon
570 Cubic Foot
4,264 Gallon
Spreader Weight (Empty)
Without Truck
16,421 Lbs
16,780 Lbs
Load Capacity (Net)
37,500 Lbs
43,000 Lbs
Inside Dimensions
48” High, 90” Wide, 204” Long
48” High, 90” Wide, 228” Long
Outside Dimensions
102”
102”
Overall Length
288”
312”
Overall Height (Gate
Lowered)
133” (Based on 40” truck frame)
133” (Based on 40” truck frame)
Overall Height (Gate
Raised)
165” (Based on 40” truck frame)
165” (Based on 40” truck frame)
Unload Speed/Time
Variable
Variable
Discharge Height
48”
48”
Spread Coverage
12’ to 30’
12’ to 30’
Recommended HP
450 (Minimum) Truck
450 (Minimum) Truck
Beater Drive
PTO Driven Triple Hydrostat
Pump Driving 2 High Torque
Motors.
PTO Driven Triple Hydrostat
Pump Driving 2 High Torque
Motors.
Belt Drive/Rear Gate
Uses Truck PTO Hydraulics. Belt
Drive Speed Regulated by an
Adjustable Flow Control Valve.
Uses Truck PTO Hydraulics. Belt
Drive Speed Regulated by an
Adjustable Flow Control Valve.
Beaters
Two 42” Diameter High Speed
Vertical Beaters with Spinners,
and Double Flighting
300 RPM @ 2000 PTO RPM
Two 42” Diameter High Speed
Vertical Beaters with Spinners,
and Double Flighting
300 RPM @ 2000 PTO RPM
Belt Material & Chain
5/16” 350 PSI PVC Belt & WH124 5/16” 350 PSI PVC Belt & WH124
H.D. Combination Chain for Belt
H.D. Combination Chain for Belt
and Retention Gate Drive System and Retention Gate Drive System
Floor, Gate & Side Walls
High Density Polyethylene on
Floor, Side Walls and End Gate
Page 18
High Density Polyethylene on
Floor, Side Walls and End Gate
702-17 & 802-19 TRUCK DIMENSIONALS
101 1/4"
133 3/4"
802-19 (180" CT)
702-17 (162" CT)
40" TRUCK FRAME
802-19 (320 3/4")
702-17 (302 3/4")
Page 19
How to read a Roto-Mix Serial Number
4 1 01 5 0157
Manufactured Location
Year Manufactured
Month Manufactured
Consecutive Numbering
Page 20
REPAIR PARTS
702-17 & 802-19
TABLE OF CONTENTS
702-17 & 802-19 Spreader Assembly ................................................................... 22-25
Truck Box Assembly ............................................................................................. 26-29
Box sides & Floor .................................................................................................. 31-33
Beater Assembly ................................................................................................... 34-37
Front Gate Assembly ............................................................................................... 38
Rear Gate Assembly1 .............................................................................................. 39
Spreader Hydraulic Parts ..................................................................................... 40-47
Spreader Truck Wiring Harness Diagram ........................................................... 48-49
Truck Spreader Mount Kit ....................................................................................... 50
Spreader Controller Box & Stand .......................................................................... 52
Spreader Decals ....................................................................................................... 53
Page 21
702-17 & 802-19 SPREADER ASSY
WITH STEEL SIDES
19
17
19
2
11
8
2
12
18
6
10
1
5
19
15
9
3
14
7
13
16
4
20
21
Page 22
9
19
702-17 & 802-19 SPREADER ASSY
WITH STEEL SIDES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PART #
130643
130763
130764
130770
131618
131619
322561
351036
364074
400812
400907
400908
407104
407415
730124
730197
730213
830304
830305
830336
830640
830580
DESCRIPTION
802 FRONT SILAGE EXTENSION
802 FRONT GATE BELT CLAMP
802 PLATE BELT CLAMP
802 FRONT GATE COVER
LEFT SILAGE EXTENSION BRACKET
RIGHT SILAGE EXTENSION BRACKET
CHAIN, WELDED MILL - 4.063 PITCH (RDB 1102-23)
702 BELT, .275" (7 mm) x 90" x 244" LG
HYDRAULIC CYLINDER 3" x 8" x 20-1/4"
HEX NUT, 3/4"-10 CENTER-LOC #5 PLTD
HEX CROWNLOC NUT 7/16"-20 #C PLTD
HEX CROWN LOCNUT 1/2"-13 #9
CHCS 1/2"-13 x 2" #5 PLTD
SHOULDER BOLT, 1"D x 5"LG x 3/4"-10 THREAD
802 FRONT GATE ASSY
702 VERTICAL BEATER ASSY. (TRAILER)
702/802 REAR GATE ASSEMBLY (SS)
802 CHAIN / BELT ADAPTER W/A
802 PIVOT PIN W/A
802 SCREEN SHIELD W/A
702-17 SPREADER BOX WA, SS SIDES
802-19 SPREADER BOX WA, SS SIDES
Page 23
QTY.
1
2
1
1
1
1
1
1
2
2
14
15
15
1
1
1
1
1
4
1
1
1
702-17 & 802-19 SPREADER ASSEMBLY
31
28
31
27
26
12
7
17
18
5
10
20
11
3
16
23 16
23
30
25
31
6
19
14
29
24
2
1
23 16
14
32
Page 24
31
702-17 & 802-19 SPREADER ASSEMBLY
,7(0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
3$57
130643
130646
130647
130759
130763
130764
130770
130790
130954
322561
322561
322561P
351029
351036
364074
400107
400114
400907
400908
400812
404008
405652
405704
407101
407103
407415
407900
730124
730126
730211
830304
830305
830336
'(6&5,37,21
802 FRONT SILAGE EXTENSION, 32-1/4" x 88-1/2"
SILAGE EXTENSION MOUNT BRACKET, L/H, 16-1/4" x 48"
SILAGE EXTENSION MOUNT BRACKET, R/H, 16-1/4" x 28"
802 FRONT GATE GUIDE, UHMW, 15-7/8"
802 FRONT GATE BELT CLAMP, 41"
802 PLATE BELT CLAMP, 2" x 88"
802 FRONT GATE COVER, 20-1/2" x 88"
802 UPPER PIVOT PLATE, 6-1/2" x 5-1/2"
WASHER 3/16" x 1-1/2" SQ
802 CHAIN, WELDED MILL, 4.063 PITCH - 22.66 FT.
702 CHAIN, WELDED MILL, 4.063 PITCH - 20.66 FT.
CONNECTOR PIN, 1" WH124HD MILL CHAIN
802 BELT, 5/16" x 90" x 268"
702 BELT, 5-16" x 90" x 244"
HYDRAULIC CYLINDER 3" x 8" x 20-1/4"
HEX SERRATED FLANGE NUT, 3/8"-16, #5 PLTD
HEX SERRATED FLANGE NUT, 1/2"-13, #5 PLTD
HEX CROWNLOC NUT 7/16"-20 #C PLTD
HEX CROWN LOCNUT 1/2"-13 #9
HEX NUT, 3/4"-10 CENTER-LOC #5 PLTD
COTTER PIN, 5/16" x 1-1/2"
HHCS, 3/8"-16 x 3/4", #5 PLTD
HHCS 1/2"-13 x 1-3/4" #5 PLTD
CARRIAGE BOLT, 1/2"-13 X 1-1/4"
CARRIAGE BOLT, 1/2"-13 x 1-3/4"
SHOULDER BOLT, 1" x 5" x 3/4"-10 THD
HHCS 3/8"-16 x 3/4" SERRATED #5 PLTD
802 FRONT GATE ASSY
802 REAR GATE ASSEMBLY
802 BEATER ASSY ( HEAVY DRIVE W/O DOORS)
802 CHAIN / BELT ADAPTER WA
802 PIVOT PIN WA
802 SCREEN SHIELD WA
Page 25
47<
1
1
1
2
2
1
1
2
20
1
1
1
1
1
2
4
21
14
15
1
1
4
10
17
19
1
9
1
1
1
1
4
1
702-17 & 802-19 SPREADER BOX ASSEMBLY
WITH STEEL SIDES
19
15
30
48
6
40
4
17
5
35
35
35
5
4
19
43 24
8
31
46
52
49
45
40
17
27 39
16
41
53
50
14
10
55
12
54
20
42
21
11
47
17
6
9
34
51
23 38
37
1
2
43 24
22 26
32
24
33 28
9
3
13
Page 26
34
7
36
10
20
17
702-17 & 802-19 SPREADER BOX ASSEMBLY
WITH STEEL SIDES
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
19
20
21
22
23
24
26
27
28
30
31
32
33
34
35
36
37
38
39
40
41
42
43
45
46
47
48
49
50
51
52
53
54
55
PART #
130664
130749
130785
130788
130790
130820
130836
131514
131611
340539
340942
344161
351048
357512
357513
360050
400107
400114
400116
400120
400216
400812
401106
402016
402406
402516
405604
405653
405657
405834
407040
407103
407140
407141
407475
407818
407901
407913
407924
410029
452860
452861
830298
830318
830319
830428
830607
830640
830580
830681
344274
409063
DESCRIPTION
802 BEARING SHAFT
802 BELT ADJUSTER BRACKET
802 BROOM CLAMP
802 PIVOT PLATE
802 UPPER PIVOT PLATE
HAZARD LIGHT MOUNTING BRACKET
BROOM 8" BRISTLES x 30" LONG
REAR GATE PROXIMITY SENSOR BRACKET
SPACER, BELT
BEARING, 2-7/16 I.D.
PILLOW BLOCK BEARING 2-15/16"
GEARBOX, BREVINI ED2150/391030/26.6/00 B3
BROOM 8" BRISTLES x 60" LG
LIGHT ASSEMBLY, LEFT HAND
LIGHT ASSEMBLY, RIGHT HAND
HYD MOTOR, 18.7 CI,14 T "A" MNT w/SPD SENS
HEX NUT, 3/8"-16 SERRATED FLANGE #5
HEX NUT, 1/2-13 SERRATED FLANGE #5
HEX NUT, 3/4"-10 SERRATED FLANGE #5 PLTD
HEX NUT, 5/8"-11 SERRATED FLANGE #5 PLTD
Hex Nut 1"-8 #5 PLTD
HEX NUT, 3/4"-10 CENTER-LOC #5 PLTD
HEX NUT, 3/8"-16 NYLOC #5 PLTD
SPLIT LOCK WASHER 1" MED PLTD
FLAT WASHER 3/8" PLTD
FLAT WASHER, 1" SAE
HHCS 1/4"-20 x 1" #5 PLTD
HHCS 3/8"-16 x 1" #5 PLTD
HHCS 3/8"-16 x 2" #5 PLTD
HHCS 1" x 4 1/2" #5 PLTD
CHCS 3/8"-16 x 1" #5 PLTD
CHCS 1/2"-13 x 1-3/4" #5 PLTD
CHCS 3/4"-10 x 2" #5 PLTD
CHCS 3/4"-10 x 2-1/2" #5 PLTD
HHCS 3/4"-10 x 4" #5 PLTD FULL THREAD
HHCS METRIC 10mm-1.5 x 80mm ( GRD 10.9)
HHCS 3/8"-16 X 1" SERRATED #5 PLTD
HHCS 1/2"-13 x 1-1/2" SERRATED #5 PLTD
HHCS 5/8"-11 x 2-1/2" SERRATED #5 PLTD
BELLVILLE DISC SPRING, 1" OD x .406 ID x .106THICK
SENSOR, PROXIMITY (ALLIED 501-0722)
SENSOR WIRE ADAPTERM, RIGHT ANGLE
802 DRIVE SPROCKET W.A.
HAZARD LIGHT MOUNTING BRACKET W.A.
362/532/672 SLOW SIGN BRACKET W.A.
GEARBOX BRACKET W/A
702-1202 BELT IDLER W.A. (NARROW)
702-17 SPREADER BOX WA, SS SIDES
802-19 SPREADER BOX WA, SS SIDES
HAZARD LIGHT MOUNTING BRACKET W.A.
FLANGE KIT, BREVINI SAE/A/ CS 14T IMP.
SHCS, 1/2"-13 x 1-1/4" LG
Page 27
QTY.
1
1
1
2
2
2
1
1
2
2
1
1
1
1
1
1
14
12
8
10
2
1
10
2
8
2
8
4
6
2
10
10
4
4
1
8
4
2
10
4
1
1
1
1
1
1
1
1
1
1
1
2
702-17 & 802-19 SPREADER BOX ASSEMBLY
16
9
3
8
24
29
37
28
24
9
8
19 30
15
32
12
14
31
33
15
2
35
17
11
34
26
36
23
5
25
1
10
22
18
Page 28
6
21
27
4
7
13
20
16
702-17 & 802-19 SPREADER BOX ASEMBLY
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
PART #
130664
130743
130749
130785
130788
130790
130836
130938
340539
340942
344121
344145
351048
360050
400114
400116
400120
400216
400812
400906
401106
402016
402516
405050
405657
405834
407103
407140
407141
407475
407820
407840
407913
407924
830280
830340
830580
830640
830298
830307
DESCRIPTION
802 BEARING SHAFT
802 GEARBOX BRACKET
802 BELT ADJUSTER BRACKET
802 BROOM CLAMP
802 PIVOT PLATE
802 UPPER PIVOT PLATE
BROOM 8" BRISTLES x 30" LONG
702/802 FILLER, HDPE-UVI, 1/2" x 16" x 14-1/4"
BEARING, 2-7/16 I.D.
PILLOW BLOCK BEARING 2-15/16"
GEARBOX, BREVINI
MOTOR ADAPTER KIT, BREVINI 2 BOLT "B"MOUNT
BROOM 8" BRISTLES x 60" LG
HYD MOTOR, 18.7 CI,14 T "A" MNT w/SPD SENS
HEX NUT, 1/2-13 SERRATED FLANGE #5
HEX NUT, 3/4"-10 SERRATED FLANGE #5 PLTD
HEX NUT, 5/8"-11 SERRATED FLANGE #5 PLTD
Hex Nut 1"-8 #5 PLTD
HEX NUT, 3/4"-10 CENTER-LOC #5 PLTD
HEX NUT, 3/8"-16 CROWN LOC #5 PLTD
HEX NUT, 3/8"-16 NYLOC #5 PLTD
SPLIT LOCK WASHER 1" MED PLTD
FLAT WASHER, 1" SAE
TRUSS HEAD SCREW, 3/8"-16 x 1 1/4" LG
HHCS 3/8"-16 x 2" #5 PLTD
HHCS 1" x 4 1/2" #5 PLTD
CHCS 1/2"-13 x 1-3/4" #5 PLTD
CHCS 3/4"-10 x 2" #5 PLTD
CHCS 3/4"-10 x 2-1/2" #5 PLTD
HHCS 3/4"-10 x 4" #5 PLTD FULL THREAD
HHCS METRIC 10mm-1.5 x 100mm
SHCS 12mm x 35mm LG 1.75P ( 8.8 )
HHCS SERRATED, 1/2"-13 x 1-1/2", #5 PLTD
HHCS 5/8"-11 x 2-1/2" SERRATED #5 PLTD
802-19 SPREADER BOX WA, HDPE SIDES (PLASTIC)
702-17 SPREADER BOX WA, HDPE SIDES (PLASTIC)
802-19 SPREADER BOX WA, (SS SIDES)
702-17 SPREADER BOX WA, (SS SIDES)
802 DRIVE SPROCKET W.A.
802 BELT IDLER W.A.
Page 29
QTY.
1
1
1
1
2
2
1
2
2
1
1
1
1
1
12
8
10
2
1
8
6
2
2
8
6
2
10
4
4
1
8
2
2
10
1
1
1
1
1
1
This page intentionally left blank.
Page 30
702-17 & 802-19 SPREADER BOX FLOOR PANELS
WITH STEEL SIDES
2
1
2
2
5
3 4
1
ITEM #
PART #
1
2
3
4
5
6
7
8
131661
131662
401106
402606
407323
407818
402406
402006
2
DESCRIPTION
FLOOR, CENTER HDPE-UVI 1102/702
FLOOR, SIDE, HDPE-UVI, 1102/702
HEX NUT, 3/8"-16 NYLOC #5 PLTD
FENDER WASHER 3/8" x 1 1/2" PLTD
ELEVATOR BOLT PLTD 3/8"-16 x 1-1/2"
HHCS METRIC 10mm-1.5 x 80mm ( GRD 10.9)
FLAT WASHER 3/8" PLTD
WASHER SPRING LOCK 3/8" MED PLTD
Page 31
QTY
2
4
40
40
40
4
4
4
702-17 SPREADER BOX SIDES & FLOOR
USED ONLY ON SPREADERS
WITH PLASTIC SIDES
6
1
6
4
5
1
3
4
3
2
802-19 SPREADER BOX SIDES & FLOOR
4
USED ONLY ON SPREADERS
WITH PLASTIC SIDES
4
1
1
3
8
2
7
6
3
3
2
5
6
7
8
3
9
Page 32
702-17 SPREADER BOX SIDES & FLOOR
ITEM #
1
2
3
4
5
6
PART #
130320
130671
130672
130941
130942
130943
DESCRIPTION
HDPE SIDE, FRONT - SPREADER,1/2" x 48" x 120"
802 HDPE-UVI FLOOR, CENTER 1/2" x 48" x 127"
802 HDPE-UVI FLOOR STRIP 1/2" x 20" x 127"
FLOOR, SIDE STRIP, HDPE-UVI, 103"
FLOOR, CENTER, HDPE-UVI, 103"
SIDE, REAR, HDPE-UVI, 108 "
QTY.
2
1
2
2
1
2
802-19 SPREADER BOX SIDES & FLOOR
ITEM #
1
2
3
4
5
6
7
8
9
PART #
130320
130671
130672
130673
130314
401106
402606
405050
830280
830340
830580
830640
DESCRIPTION
HDPE SIDE, FRONT - SPREADER,1/2" x 48" x 120"
802 HDPE-UVI FLOOR, CENTER 1/2" x 48" x 127"
802 HDPE-UVI FLOOR STRIP 1/2" x 20" x 127"
802 HDPE-UVI SIDE, REAR, 1/2" x 48" x 132"
SPACER - 3/8" ID x 9/16" OD x 11/16" LG
HEX NYLOC NUT, 3/8"-16, #5 PLTD
FENDER WASHER PLTD. 3/8"ID x 1 1/2"OD
TRUSS HD SCREW, 3/8"-16 x 1-1/4"
802-19 SPREADER BOX WA, HDPE SIDES (PLASTIC)
702-17 SPREADER BOX WA, HDPE SIDES (PLASTIC)
802-19 SPREADER BOX WA, (SS SIDES)
702-17 SPREADER BOX WA, (SS SIDES)
Page 33
QTY.
2
2
4
2
1
2
2
2
1
1
1
1
702-17 & 802-19 SPREADER BEATER ASSEMBLY
86(7+,6$66(0%/<
)256(5,$/180%(56
%()25(
22
6 10
22
9
9
29
20
29
1
16
16
16
20
25
24
8
11
30
32
18
1
16
12
24
20
12
16
16
2
18
16
2
21 17
33
24
16
34
20
31
17 21
4
14
13
31
16
27
15
26
3
21 17
28
26
5
3
23
Page 34
17 21
16
702-17 & 802-19 SPREADER BEATER ASSEMBLY
86(7+,6$66(0%/<)256(5,$/180%(56%()25(
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PART #
130378
130708
130748
130750
130829
130830
130830
310750
340425
356001
356002
360032
385006
385009
401106
401108
402008
402508
405701
405702
405703
405704
407041
407102
407104
830284
830285
830286
830287
830290
830301
830312
830355
830356
DESCRIPTION
DOOR LINK
802 BEATER SKIRT FILLER PLATE, 20" x 42-1/2"
802 BEATER MOTOR SPACER, 5/8"
802 ANGLE DEFLECTOR ( 4 1/2" x 10" )
802 PADDLE WEAR PLATE
GREASE LINE, 3/16" x 84" COPPER
GREASE LINE, 3/16" COPPER
GREASE ZERK 1/8" PLTD
BEARING, 4-BOLT FLANGE, 1-1/2", RCJ
COMPRESSION FITTING 1/8"MP x 3/16" TUBE, 90°
COMPRESSION FITTING 1/8"MP x 3/16" TUBE, STRT
HYDRAULIC MOTOR, 30.7 CID VIS
AUGER KNIFE 8", LEFT HAND
AUGER KNIFE 8", RIGHT HAND
HEX NUT, 3/8"-16 NYLOC #5 PLTD
HEX NYLOC NUT, 1/2"-13, #5 PLTD
SPRING LOCK WASHER 1/2" PLTD
FLAT WASHER, 1/2" ID x 1" OD
HHCS, 1/2"-20 x 1", #5 PLTD
HHCS, 1/2"-13 x 1-1/4", #5 PLTD.
HHCS, 1/2"-13 x 1-1/2", #5 PLTD.
HHCS 1/2"-13 x 1-3/4" #5 PLTD
CHCS 3/8"-16 x 1-1/4" #5 PLTD
CARRIAGE BOLT, 1/2"-13 X 1-1/2", #5 PLTD
CHCS 1/2"-13 x 2" #5 PLTD
DRIVE FLANGE WA
802 LEFT HAND VERTICAL BEATER WA
802 RIGHT HAND VERTICAL BEATER WA
802 BEATER DOOR WA
802 VERTICAL BEATER FRAME WA
802 BEATER IDLER SHAFT WA
DEFLECTOR WA
702/802 LEFT HAND CHISEL POINT DEFLECTOR
702/802 RIGHT HAND CHISEL POINT DEFLECTOR
Page 35
QTY.
2
2
2
48
8
1
1
2
2
2
2
2
22
22
16
129
16
3
4
18
16
8
16
96
8
2
1
1
2
1
2
1
24
24
702-17 802-19 SPREADER BEATER ASSEMBLY
86(7+,6$66(0%/<)256(5,$/180%(56%(*,1,1*:,7+
42
36 23
42
40
23 37
10
2
50
21
18 21 38
19
40
12
27 33
32
27
16
44 23 37
45
20
31
9
39
8
26 30
21
13
4 11 14 15
49
37
43
25 28
25 28
37
48
35
46
47
25
17
3 24 34
17
25
6
3 24 34
41
1
22
1
7
5
Page 36
29
702-17 & 802-19 SPREADER BEATER ASSEMBLY
86(7+,6$66(0%/<)256(5,$/180%(56%(*,1,1*:,7+
,7(0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
3$57
130708
130750
130829
130830
131205
131208
131262
131278
131279
131283
310750
330401
340425
356001
356002
358441
360048
385006
385009
400107
400114
400145
400909
401106
401108
402008
402110
402508
405702
405703
405704
405705
405750
407041
407104
407117
407118
407553
407900
407913
409063
409100
830312
830355
830356
830395
830396
830397
830425
830427
'(6&5,37,21
47<
802 BEATER SKIRT FILLER PLATE, 20" x 42-1/2"
2
802 ANGLE DEFLECTOR ( 4 1/2" x 10" ) (OPTIONAL PARTS)
48
802 PADDLE WEAR PLATE
8
GREASE LINE, 3/16" COPPER
2
SPLINED ADAPTER, (BEATER DRIVE)
2
SPLINED HUB (BEATER DRIVE)
2
KEY, 7/16" SQUARE x 1-1/4" LG.
2
SENSOR MOUNT, 802
2
SENSOR PLATE
2
SAW TEETH, 702/802 SPREADER (OPT. PARTS)
24
GREASE ZERK 1/8" PLTD
2
SPROCKET, 40A30, No. 40 - 1/2" Pitch
2
BEARING, 4-BOLT FLANGE, 1-1/2", RCJC
2
COMPRESSION FITTING 1/8"MP x 3/16" TUBE, 90°
2
COMPRESSION FITTING 1/8"MP x 3/16" TUBE, STRT
2
HALL EFFECT SPEED SENSOR HARNESS
2
HYD MOTOR, 30.7 CI 1-1/2" TAPERED SHAFT
2
AUGER KNIFE 8", LEFT HAND (OPTIONAL PARTS)
22
AUGER KNIFE 8", RIGHT HAND (OPTIONAL PARTS)
22
HEX NUT, 3/8"-16 SERRATED FLANGE #5
4
HEX NUT, 1/2"-13 SERRATED FLANGE #5 PLTD
AR
HEX NUT, THIN 1-1/4"-18 UNEF THD (EXTRA FINE)
2
HEX CENTER LOCKNUT 1/2"-13 #8
AR
HEX NYLOC NUT, 3/8"-16, #5 PLTD
16
HEX NUT, 1/2"-13 NYLOC #5 PLTD
27
SPRING LOCK WASHER 1/2" PLTD
8
LOCK WASHER 5/8" EXTERNAL STAR PLTD
4
FLAT WASHER, 1/2" ID x 1" OD
3
HHCS 1/2"-13 x 1-1/4" #5 PLTD
8
HHCS, 1/2"-13 x 1-1/2", #5 PLTD.
8
HHCS 1/2"-13 x 1-3/4" #5 PLTD
4
HHCS 1/2"-13 x 2" #5 PLTD
4
HHCS 5/8"-11 x 1" #5 PLTD
2
CHCS 3/8"-16 x 1-1/4" #5 PLTD
16
CHCS 1/2"-13 x 2" #5 PLTD
8
CHCS 1/2"-13 x 2" #8 PLTD
AR
CHCS 1/2"-13 x 1-1/2" #8 PLTD
AR
Socket Flat Hd Cs, 1/2" X 2"
AR
HHCS 3/8"-16 x 3/4" SERRATED #5 PLTD
4
HHCS 1/2"-13 x 1-1/2" SERRATED #5 PLTD
9
SHCS, 1/2"-13 x 1-1/4" LG
8
BHSCS 1/2"-13 x 1-1/2" #8
2
DEFLECTOR WA
1
702/802 LEFT HAND CHISEL POINT DEFLECTOR
24
702/802 RIGHT HAND CHISEL POINT DEFLECTOR (OPTIONAL PARTS)
24
702/802 L/H VERTICAL BEATER W/A (HEAVY SPLINE)
1
802 R/H VERTICAL BEATER W/A (HEAVY SPLINE)
1
802 VERTICAL BEATER FRAME W/A (2ND GEN)
1
802 BEATER IDLER SHAFT W/A (SPEED SENSOR)
2
COVER, 702/802 SPEED SENSOR W/A
1
$5 $65(48,5('
Page 37
702-17 & 802-19 SPREADER FRONT GATE ASSEMBLY
2
17
2
1
18
17
3
1
16
5
12
14
10
6
8
11
4
13
9
9
11
7
3
15
ITEM #
PART #
DESCRIPTION
1
130428
SCRAPER, 6-1/2" x 48"
2
2
130429
CLAMP SCRAPER, 44-1/2"
2
3
130759
802 UHMW FRONT GATE GUIDE, 15-7/8
2
4
130760
802 FRONT GATE CHAIN ADAPTER, 16"
1
5
130762
802 CHAIN LUG, 3-1/2"
1
6
130770
802 FRONT GATE COVER, 20-1/2" x 88"
1
7
130956
802 WASHER, 1/2" x 1-1/16" x 3"
1
8
322561P
CONNECTOR PIN, 1" WH124HD MILL CHAIN
1
9
351987
PIRANHA URETHANE STRIPPER, 3" x 2-1/4 OD
2
10
400216
HEX NUT, 1"-8, #5 PLTD
1
11
400616
HEX JAMNUT, 1"-8, #5 PLTD
2
12
402016
SPRING LOCK WASHER, 1", MED, PLTD
1
13
402416
FLAT WASHER, 1", MED, PLTD
1
14
404008
COTTER PIN, 5/16" x 1-1/2"
1
15
407730
STUD BOLT, RIBBED NECK, 7/16"-20 UNF x 1-3/4"
14
16
407900
HHCS SERRATED, 3/8" -16 x 3/4", #5 PLTD
10
17
407902
HHCS SERRATED 3/8"-16 x 1-1/2" #5 PLTD
14
18
830292
802 FRONT GATE W.A.
1
Page 38
QTY.
702-17 & 802-19 SPREADER REAR GATE ASSEMBLY
10
3
3
17
1
2
8
14
12
18
1
9
2
9
16
13
11
5
6
4
20
15
7
5
9
13
15
5
5
4
19
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART #
130439
130440
130739
130746
130747
130757
130758
130780
401106
401108
401112
405050
405659
405718
407413
407902
830283
830303
830311
830313
DESCRIPTION
FLASHING SEAL CLAMP
FLASHING, SWINGING GATE
802 REAR GATE PIVOT BLOCK, 4-1/2"
802 REAR GATE GUIDE PLATE (3 1/2 x 6 )
802 GUIDE WEAR BLOCK, UHMW
802 GUIDE SPACER, 6"
802 GUIDE SPACER, 7 GA.
REAR GATE COVER, HDPE, 1/2" x 48" x 80-1/2"
HEX NUT, 3/8"-16 NYLOC #5 PLTD
HEX NYLOC NUT, 1/2"-13, #5 PLTD
HEX NUT, 3/4"-10 NYLOC #5 PLTD
TRUSS HD SCREW, 3/8"-16 x 1-1/4"
HHCS 3/8-16 x 2-1/2 #5 PLTD
HHCS, 1/2"-13 x 6-1/2", # 5 PLTD.
SHOULDER BOLT, 1"D x 3" LG x 3/4"-10
HHCS SERRATED 3/8"-16 x 1-1/2" #5 PLTD
802 REAR GATE ARM W.A.
802 REAR GATE W/A
802 REAR GATE GUIDE W.A. (LEFT HAND)
802 REAR GATE GUIDE W/A
Page 39
11
6
7
QTY.
2
2
6
2
4
2
2
1
44
6
2
24
8
6
2
12
1
1
1
1
9
702-17 & 802-19 HYDRAULICS
WITH DUAL HYDRAULIC MANIFOLD
11
11
1
1
2
13
12
8
7
4
,7(0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
6
5
3$57
360048
360050
362037
362118
362120
362121
362382
362383
362404
362442
364074
368527
730141
730199
3
10
9
14
'(6&5,37,21
HYD MOTOR, 30.7 CI 1-1/2" TAPERED SHAFT
HYD MOTOR, 18.7 CI,14 T "A" MNT w/SPD SENS
PUMP, 1.87 CIR GEAR (L/H ROTATION)
PUMP, 6.0 CIR LOAD SENSE - L/H ROT
PUMP, LOAD SENSE 2.32 CIR - L/H ROT.
PUMP, 6.0 LOAD SENSE - L/H ROT.
MANIFOLD, 702/802 BEATER DRIVE
MANIFOLD, FLOOR/GATE (702/802) LOAD SENSE
FILTER HEAD, 1-1/4" FP
FILTER ELEMENT 1-1/4"
HYDRAULIC CYLINDER 3" x 8" x 20-1/4"
BALL VALVE, 1-1/4" FP
802 TRAILER SPREADER RESERVOIR
802 MANIFOLD COVER ASSY
Page 40
47<
2
1
1
1
1
1
1
1
2
1
2
2
1
1
&$6('5$,1
(;&(66&+$5*(
75(7851/,1(
)/225
02725
&$6('5$,1
Page 41
%($7(5380335(6685(
75(7851/,1(
)/2250272535(6685(
)/225027255(7851
/2$'6(16(
/2$'6(16(
%($7(5380335(6685(
(;&(66&+$5*(
36,
&+(&.
9$/9(
33257
&/26('
/22336,
/2$'6(16(
)/225*$7(36,
68&7,21/,1(
68&7,21/,1(
5(7851)52002725
5(7851)52002725
*$/
5(6(592,5
75(7851/,1(
75(7851/,1(
3
2
%($7(5
0$1,)2/'
7239,(:
57
33257
353257
33257
353257
33257
7
03257
03257
&3257
)/225
0$1,)2/'
7239,(:
/63257
7
7
&3257
03257
053257
/+%($7(5
02725
/2$'6(16(/,1(
68&7,21/,1(
5(7851/,1(
/2:35(6685(
+,*+35(6685(
0272535(6685(
027255(7851
027255(7851
0272535(6685(
053257
5+%($7(5
02725
5($5*$7(&</,1'(56
03257
&</,1'(583
&</,1'(5'2:1
02725&$6('5$,1
702-17 & 802-19 HYDRAULIC SCHEMATIC
WITH DUAL HYDRAULIC MANIFOLDS
702-17 & 802-19 SPREADER HYDRAULIC TANK,
MOTORS & CYLINDERS
3
16
31
24
3
28
24
4
16
38
43
29
37
21
29
9
18
13
9
40
39
21
17
28
9
15
8
14
33
9
26
14
32
8
33
26
32
8
1
8
9
22
15
26
7
32
15
19
12
5
36
42
22
6
2
41
12
43
10
18
25
35
30
34
11
Page 42
23
20
27
30
34
23
702-17 & 802-19 SPREADER HYDRAULIC TANK,
MOTORS & CYLINDERS
,7(0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
3$57
130889
130890
360048
360050
362552
362555
364074
366008
366032
366040
366085
367079
367097
367098
367100
367101
367135
367137
367141
367152
367171
368016
368036
368082
368134
368136
368137
368417
368468
368527
368618
368625
368636
368648
368666
368691
781751
781752
781753
781754
781774
781780
781781
830317
'(6&5,37,21
802 TRUCK RESERVOIR BRACKET (R/H)
802 TRUCK RESERVOIR BRACKET (L/H)
HYD MOTOR, 30.7 CI 1-1/2" TAPERED SHAFT
HYD MOTOR, 18.7 CI,14 T "A" MNT w/SPD SENS
SIDE FILLER HI-NECK ASSY
SIGHT GAUGE 5"
HYDRAULIC CYLINDER 3" x 8" x 20-1/4"
HOSE, 1/2"-2, 8M3K (3000PSI)
HOSE, 3/4"-2, 12M3K (3000PSI)
HOSE, 1", 16GMV (300PSI)
HOSE, 1-1/4", 20GMV (250PSI)
HOSE COUPLING, 6G-6FJX x 3/8"
HOSE COUPLING 1/2" x 3/4" JIC (8G-8FJX90)
HOSE COUPLING 1/2" x 13/16"FFORX90S
HOSE COUPLING 1/2" x 13/16"FFORX
HOSE COUPLING 1/2" x 3/4"FJX ,8G-8FJX
HOSE STEM 1" x 16GS-16FFORX
HOSE COUPLING 1" x 16G-16FFORX
HOSE COUPLING, 3/4"x 1-3/16 FFFORX
HOSE COUPLING 20G-20FFORX x 1-1/4
HOSE COUPLING, 3/4"x 1"-14 FFFORX
90º ELBOW, 3/8"MP x 9/16"JIC
HYDRAULIC ADAPTER 1-1/4"MP x 1-1/4"FP 90º
90º ELBOW, 9/16"MOR x 3/4"JIC
STRAIGHT ADAPTER, 1" MP x 1-7/16" ORFS
STRAIGHT ADAPTER, 3/4" MP x 13/16" FFOR
HYDRAULIC ADAPTER 1-1/4"MP x 1-11/16"FFOR
STRAIGHT ADAPTER, 1-7/16" FFOR x 1-1/16" MORB
STRAIGHT ADAPTER, 1"-14 FFOR x 7/8" MORB
BALL VALVE, 1-1/4" FP
TEE, 3/4" JIC SWIVEL RUN
HYD ADAPTER 90º, 1" MP x 3/4" FP
TEE RUN, 13/16" ORFS SWIVEL
HEX NIPPLE, 1-1/4" MP x 1-1/4" MP
HEX REDUCER, 1-1/4" MP x 1" FP
HYDRAULIC ADAPTER, 90° 1"MP x 1-3/16 FFOR
HOSE ASSY, 1" x 1-7/16 FFORX x 1-7/13 FFORX
HOSE ASSY, 1" x 1-7/16 FFORX x 1-7/16 FFORX
HOSE ASSY 1" x 1-7/16 FFORX x 1-7/16 FFORX90S
HOSE ASSY, 1" x 1-7/16 FFORX x 1-7/16 FFORX
HOSE ASSY, 3/8" x 9/16 FJX x 9/16 FJX
HOSE ASSY, 3/8" x 9/16 FJX x 9/16 FJX
HOSE ASSY, 1/2" x 3/4 FJX x 3/4 FJX
802 TRUCK HYDRAULIC RESERVOIR, 55GAL
Page 43
47<
1
1
2
1
1
1
2
AR
AR
AR
AR
10
1
8
8
2
6
7
5
2
2
4
2
2
3
3
1
4
6
2
1
3
4
2
5
1
1
1
1
1
1
1
1
1
AR = AS REQUIRED
702-17 & 802-19 HYDRAULIC PUMPS & FILTERS
19 45 30 40 1 22 27 19 20 46 1 27 22 16 16 6 17 25 31 34 18 11 14 30
12
19
20
12
40
13
30
24
2
29
3
41
5
9
33
41
18
29
37
23
21
44
11
12
15 7 33 18 37 21 11 15 26 35 24 4 32 22 13
12
20
28
19
12 19 36 41
Page 44
9
10 41 42 38 43
8
28 39
702-17 & 802-19 HYDRAULIC PUMPS & FILTERS
,7(0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
3$57
130787
185480
338406
362037
362037-R
362118
362118-R
362120
362120-R
362121
362121-R
362231
362404
362442
366006
366008
366032
366040
366041
366045
366085
367080
367098
367100
367132
367139
367141
367142
367152
368097
368134
368135
368177
368191
368192
368193
368195
368196
368302
368415
368458
368608
368634
368636
368666
368667
368690
781767
781785
781786
'(6&5,37,21
FLANGE ADAPTER, 2 1/2" CODE 61 x 1" FP
3/8" SQ. X 2" KEY
COMPANION FLANGE, 1350, 1-1/2"
PUMP, 1.87 CIR GEAR (L/H ROTATION) STD-TRANS
PUMP, 1.87 CIR GEAR (R/H ROTATION) AUTO-TRANS
PUMP, 6.0 CIR LOAD SENSE - (L/H ROTATION) STD-TRANS
PUMP, 6.0 CIR LOAD SENSE - (R/H ROTATION) AUTO-TRANS
PUMP, LOAD SENSE 2.32 CIR - (L/H ROTATION) STD-TRANS
P, LOAD SENSE 2.32 CIR - (R/H ROTATION) AUTO-TRANS
PUMP, 6.0 LOAD SENSE - (L/H ROTATION) STD-TRANS
PUMP, 6.0 LOAD SENSE - (R/H ROTATION) AUTO-TRANS
CHECK VALVE, 1/2" FP x 1/2" FP (25 PSI)
FILTER HEAD, 1-1/4" FP
FILTER ELEMENT 1-1/4"
HOSE, 6M3K 3/8"-2 (3000 PSI)
HOSE, 8MSK 1/2"-2 (3000 PSI)
HOSE, 12M3K 3/4"-2 (3000 PSI)
HOSE, 16GMV 1" (300 PSI)
HOSE, 16EFG5K 1"-5 (5000 PSI)
HOSE, 16G1H-1 1"-1 (1000 PSI)
HOSE, 20GMV 1-1/4" SPIRAL WIRE SUCTION
HOSE COUPLING 3/8" x 11/16"FFORX90S
HOSE COUPLING 1/2" x 13/16"FFORX90S
HOSE COUPLING 1/2" x 13/16"FFORX
HOSE STEM, 16GS-16FL90 1"
HOSE COUPLING 1" x 16G-16FFORX90S
HOSE COUPLING, 3/4"x 1-3/16 FFFORX
HOSE COUPLING 3/4" x 1-3/16"FFORX90S
HOSE COUPLING 20G-20FFORX x 1-1/4
ADPT, 90º ELBOW, 9/16 MOR x 13/16 FFOR
STRAIGHT ADAPTER, 1" MP x 1-7/16" ORFS
STRT ADPT, 1/2" MP x 13/16 FFOR
STRT ADPT, 1-3/16" FFOR x 1"MP
STRT ADPT, 13/16 FFOR x 7/8 MORB
STRT ADPT, 1-5/8" MOR x 1-11/16" FFOR
STRT ADPT, 1-7/16" ORFS x 1-5/16" MORB
STRT ADPT, 11/16 FFOR x 9/16 MORB
STRT ADPT, 11/16 FFOR x 7/16 MORB
STRT ADPT, 1-5/16 MOR x 1-3/16 FFOR
STRT ADPT, 1" MP x 13/16" FFOR
FLANGE. SET KIT, 1" CODE 61 ( TOMPKINS# SFK-16)
STREET TEE 1/2"MP x 1/2"FP x 1/2"FP
ADPT, 90º ELBOW, 1/2"MP x 1/2"FP
TEE RUN, 13/16" ORFS SWIVEL
HEX REDUCER, 1-1/4" MP x 1" FP
HEX REDUCER, 1" MP x 1/2" FP
ADPT, 90º ELBOW, 1/2"MP x 1/2"MP
HOSE ASSY, 3/4" x 1-3/16 FFORX x 1-3/16 FFORX
HOSE ASSY, 1/2" x 13/16 FFORX90 x 13/16 FFORX90
HOSE ASSY, 1/2" x 13/16 FFORX x 13/16 FFORX90
Page 45
47<
2
1
1
1
1
1
1
1
1
1
1
1
2
2
AR
AR
AR
AR
AR
AR
AR
4
8
8
2
3
5
4
2
1
3
2
2
3
1
9
2
1
1
1
2
1
1
4
5
1
1
1
1
1
$5 $65(48,5('
702-17 & 802-19 HYDRAULIC MANIFOLD VALVE ASSY
USE THIS DIAGRAM FOR SPREADERS WITH DUAL HYD MANIFOLDS
13 26 37
20 28 9
32
6
2
1
1
1
9 21 28
10
28
21
9
7 12 30
16
25
8
19
24
11
31
4
40
31
19
24
36
19
24
34
3
18 22 24 35
7 12 23
20 28 39
18 22 24 33
14 26 38
10
0
24
22
18
24
19
11
8
25
15
18
22
24
10
9
5
17 27 8
Page 46
29 32
32 29 215
702-17 & 802-19 HYDRAULIC MANIFOLD VALVE ASSY
USE THIS DIAGRAM FOR SPREADERS WITH DUAL HYD MANIFOLDS
ITEM #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PART #
362255
362371
362382
362383
362399
362412
366006
366008
366032
366041
366045
367063
367080
367080L
367098
367099
367100
367135
367137
367141
367142
367415
368098
368193
368194
368197
368303
368468
368693
368708
407900
450766
781751
781752
781753
781754
781765
781766
781767
830423
DESCRIPTION
QTY.
VALVE, SOLENOID - 3 WAY #SV08-30M-0-N-12-ER
3
SOLENOID, PROP-N/C VALVE, # SP12-20-M-0-12-ER
1
MANIFOLD, 702/802 BEATER DRIVE
1
MANIFOLD, FLOOR/GATE (702/802) LOAD SENSE
1
SOLENOID VALVE, (VICKERS #SP12-20-C-0-00)
2
SOLENOID, N/C VALVE, #SV08-22M-0-12-ER
1
HOSE, 3/8" (366006 AS REQ'D)
AR
HOSE,1/2" (366008 AS REQ'D)
AR
HOSE, 3/4' (366032 AS REQ'D)
AR
HOSE, 1" (366041 AS REQ'D)
AR
HOSE,1" (366045 AS REQ'D)
AR
HOSE COUPLING 3/8" x 6G-6FFORX
3
HOSE COUPLING, 3/8" x 11/16"FFORX90S
1
HOSE COUPLING 3/8" x 6G-6FFORX90L
1
HOSE COUPLING 1/2" x 13/16"FFORX90S
1
HOSE COUPLING 1/2" x 8G-8FFORX90L
1
HOSE COUPLING 1/2" x 13/16"FFORX
1
HOSE STEM 1" x 16GS-16FFORX
4
HOSE COUPLING 1" x 16G-16FFORX
4
HOSE COUPLING, 3/4"x 1-3/16 FFFORX
2
HOSE COUPLING 3/4" x 1-3/16"FFORX90S
2
FERRULE, 16GS1F-4
4
90° ELBOW, 11/16" ORFS x 9/16" MOR
2
STRAIGHT ADAPTER, 1-7/16" ORFS x 1-5/16" MORB
8
STRAIGHT ADAPTER, 13/16" ORFS x 3/4" MORB
2
STRAIGHT ADAPTER, 11/16" FFOR x 3/4" MORB
2
90° ELBOW, 3/4" MOR x 13/16" FFOR
1
STRAIGHT ADAPTER, 1"-14 FFOR x 7/8" MORB
4
90° ELBOW, 9/16" MOR x 9/16" FOR
2
90° ELBOW, 11/16" ORFS x 7/16" MOR
1
HHCS 3/8"-16 x 3/4" SERRATED #5 PLTD
8
TRANSDUCER, 6000 PSI, HYDAC HDA 847K-R-6000
3
HOSE ASSY, 1" x 1-7/16 FFORX x 1-7/13 FFORX
1
HOSE ASSY, 1" x 1-7/16 FFORX x 1-7/16 FFORX
1
HOSE ASSY 1" x 1-7/16 FFORX x 1-7/16 FFORX90S
1
HOSE ASSY, 1" x 1-7/16 FFORX x 1-7/16 FFORX
1
HOSE ASSY, 3/8" x 9/16 FJX x 11/16 FFORX90S
1
HOSE ASSY, 3/8" x 9/16 FJX x 11/16 FFORX90L
1
HOSE ASSY, 3/4" x 1-3/16 FFORX x 1-3/16 FFORX
1
MOUNTING BRACKET W/A, MANIFOLD
1
$5 $65(48,5('
Page 47
702-17 & 802-19 TRUCK SPREADER
WIRING HARNESS (#358429) DIAGRAM
L
3S
BLK
16 53
BLK X
B
A
C
16
RED
49
X
M
16
WHT
58
X
B
G
16
GRN
61
X
16
PUR
63
X
SV3
FLOOR
FORWARD
1 2
1 2
16
PUR/WHT
65
1 2
X
SV4
FLOOR
BACK
SV2
REAR GATE
CLOSED
SV1
REAR GATE
OPEN
16
BRN
67
X
16
TAN
69
X
1 2
1 2
B
A
C
16 3
GRA X
J
16
RED/YEL
1
X
3S
BLK
.250
B
2S
C
F
4.0 81.0
35
16
BLK/BLU Y
36
16
BLK/RED Y
39
16
BLK/WHT Y
40
16
BLK/YEL Y
44
16
BLK/GRN Y
46
12
BLK/WHT Y
FLAG
LABEL - 7210903
SV2
REAR GATE
CLOSED
D
2S
6.0 79.0
16 51
BLK Y
16 52
BLK Y
16 53
BLK Y
12 54
BLK Y
16 64
BLK Y
16 66
BLK Y
16 68
BLK Y
16 70
BLK Y
16 71
BLK X
.250
HSG 3146125
RET 3146126
FLAG
LABEL - 7210903
SV1
REAR GATE
OPEN
E
16
BLK
70
X
C
16
BLK/GRN
44
X
.250
HSG 3146125
RET 3146126
16
BLK
68
X
A
16 45
BLU X
37
16
RED/YEL Y
38
16
RED/WHT Y
43
16
RED/GRN Y
16 47
RED Y
12 48
RED Y
16 49
RED Y
16 50
RED Y
FLAG
LABEL - 7210903
SV4
FLOOR
BACK
2S
16
RED/GRN
43
B
X
2.0 83.0
.500
.250
HSG 3146125
RET 3146126
16
BLK
66
X
2S
.250
HSG 3146125
RET 3146126
A
C
FLAG
LABEL - 7210903
SV3
FLOOR
FORWARD
6400182
16 62
16 61
BLK Y GRN Y
16 71
16 72
BLK Y GRN Y
REAR GATE
LIMIT
SWITCH
FLAG
LABEL - 7210903
REAR GATE
LIMIT
SWITCH
LABEL - 7210903
358430
11.75 4.0 13.75 2.0
HSG 3146125
RET 3146126
16
RED/WHT
4
X
6
16
GRA/WHT X
FLAG
LABEL - 7210903
LEFT BEATER
SPEED
PULSE PICKUP
FLAG
LABEL - 7210903
PSV
PROPORTIONAL
FLOOR SPEED
2S
16
BLK
64
X
16
BLK/WHT
5
B
X
LEFT BEATER
SPEED
PULSE PICKUP
16
BLK/YEL
2
X
A
16
BLK
62
X
ID
LABEL
.250
HSG 3146384
RET 3146021
37
X
16
RED/YEL
41
38
40
39
X
X
X
X
16
16
ORG
16 RED/WHT
16
BLK/YEL BLK/WHT
FLAG
LABEL - 7210903
LS
FLOOR
PRESSURE
3S
BLK
7 8 9 101112
42
16
X
ORG/WHT
12P
1
605 2
314 05
G 46
HSET 31
R
C
16
RED
47
X
16 51
BLK X
PSV
PROPORTIONAL
FLOOR SPEED
.250
HSG 3146384
RET 3146021
A
16
16
16
GRA/WHT GRA
BLK/BLU
33
34
35
X
X
X
16
CAVITY PLUG
36 BLK/RED
3146079
(2)
X
6 5 4 3 2 1
3S
BLK
16 52
BLK X
LS
FLOOR
PRESSURE
FLAG
LABEL - 7210903
LS1
LEFT BEATER
PRESSURE
TRANSDUCER
FLAG
LABEL - 7210903
RIGHT BEATER
SPEED
PULSE PICKUP
16
16
GRA GRA/WHT 16
10
15
ORG
16
Y
Y
16
Y
CAVITY PLUG
17 ORG/WHT
3146079
Y
(2)
1 2 3 4 5 6
RIGHT BEATER
SPEED
PULSE PICKUP
K
3S
BLK
16
YEL
59
X
LS1
LEFT BEATER
PRESSURE
TRANSDUCER
.250
HSG 3146384
RET 3146021
3S
BLK
HS
RE G 31
T 3 46
146 38
021 4
16
RED
50
X
HSG 3146384
RET 3146021
16
YEL/WHT
LS2
RIGHT BEATER
60
B A
PRESSURE
X
TRANSDUCER
C
FLAG
LABEL - 7210903
LS2
RIGHT BEATER
PRESSURE
TRANSDUCER
16 3
GRA Y
1
16
RED/YEL Y
5
16
BLK/WHT Y
6
5
4
1
2
3
LABEL - 7210903
358433
6
5
4
13
16
BLK/YEL X
6P
HSG 3146333
RET 3146334
HSG 3146211
RET 3146212
MLD
PLUG
BRN
4
41
Page 48
ATTACH AFTER HRNS
HAS BEEN INSPECTED
LABEL - 7210903
358432
12S
HSG 3146055
RET 3146056
3S K
84
BL 463021
31146
3
G
HS ET
7 R
3P
04 8
46604
1
3 4
G 31
HSRET
8
11
16
X RED/YEL
.350
ATTACH AFTER HRNS
HAS BEEN INSPECTED
3
00
121110 9 8 7
17
X 16
14
16
ORG/WHT
12
13
Y
X
16
Y
Y
16
RED/WHT 16
16 ORG
BLK/WHT BLK/YEL
12
16
X BLK/WHT
6S
.250
HSG 3146384
RET 3146021
1
2
3
14
4
16
16
Y RED/WHT RED/WHT X
2
16
Y BLK/YEL
11
16
Y
RED/YEL
10 16
X GRA
15
6
16
16
Y GRA/WHT GRA/WHT X
A
B
C
MLD
PLUG
WHT
16
BLK/GRN
8
B
Y
16
BLU
MLD
PLUG
BLK
A
C
9
Y
16
RED/GRN
7
Y
16
RED/GRN
7
A
X
16
BLU
B
C
9
X
16
3P
BLK/GRN HS
RE G
8
T 3 31
14 46
X
60 04
48 7
702-17 & 802-19 TRUCK SPREADER
WIRING HARNESS (#358429) DIAGRAM
FLOOR
MOTOR
PULSE-PICKUP
C B A
16
RED
74
X
X
16 75
PNK Y
3S
16
16
PUR
RED/BLK
63
57
Y
16
Y
65 PUR/WHT
Y
1 2 34 5 6
16
RED/BLK
57
X
CAVITY PLUG
3146079
(3)
NONE
121110 9 8 7
75
X
16
PNK
69
16
1 2 3Y
456
6711109 8TAN
12
7
58
Y
16
Y
BRN
16
WHT
S
12 LK
26
B 462056
31146
G 3
HSRET
.250
FLAG
LABEL - 7210903
FLOOR
MOTOR
PULSE-PICKUP
16
GRN
72
45
X
C B A
3015793
H
16
BLU
Y
16
BLK
73
16
16
GRA GRA/WHT
34
33
Y
Y
CAVITY PLUG
3146079
(4)
12S
1 2 3 4 5 6
74
Y
16
RED
16
16
16 GRA/WHTGRA
ORG
18
19
20
X
X
X
CAVITY PLUG
16
3146079
ORG/WHT 21
(2)
X
.250
1 2
P
FLAG
LABEL - 7210903
FC2
RIGHT BEATER
SPEED FLOW
CONTROL
16
BLK/RED
29
Y
HSG 3146125
RET 3146126
FLAG
LABEL - 7210903
FC1
LEFT BEATER
SPEED FLOW
CONTROL
16
ORG/WHT
21
Y
2S
2S
N
56
73
X
16
Y
RED/BRN
16
BLK
.250
16
BLK/BLU
28
Y
ORG
HSG 3146125
RET 3146126
1 2
REAR GATE
LIMIT
SWITCH
16
RED/GRN
30
A
X
6 5 4 3 2 1
7 8 9 101112
27
16
X RED/YEL
26
24
25
X 16
X
X
16
RED/WHT
16
16
ORG
BLK/YEL BLK/WHT
23
X
ATTACH AFTER HRNS
HAS BEEN INSPECTED
12P
FLAG
LABEL - 7210903
REAR GATE
LIMIT
SWITCH
.250
22
16
ORG/WHT X
LABEL - 7210903
358431
HSG 3146051
RET 3146052
F
16
BLK/GRN
31
B
Y
A
C
F
7
04 8
46 04
31146
3
G
HSRET
HSG 3146055
RET 3146056
FLAG
LABEL - 7210903
REAR GATE
LIMIT
SWITCH
16
RED/GRN
30
Y
16 32
BLU Y
Page 49
B
C
16
BLK/GRN
31
X
16 32
BLU X
3P
12S
.413
3S K
84
BL 463021
31146
3
G
HSRET
42
1 2 3 Y4 5 6 16
4111109ORG/WHT
12
87
55
56
Y
16
16
Y
Y
YEL
ORG
16
16
BLK/YELRED/BRN
59
FC2
RIGHT BEATER
SPEED FLOW
CONTROL
FC1
LEFT BEATER
SPEED FLOW
CONTROL
16
ORG
20
Y
Y
46
12
X
BLK/WHT
48
X 12
RED
54
X 12
55
BLK
X
16
BLK/YEL
COIL WIRES AND
SECURE W/ WIRE
TIES (3220006) (2)
AFTER HRNS HAS
BEEN INSPECTED
NONE
(7)
16
YEL/WHT
Y
HSG 3146055
RET 3146056
121110 9 8 7
60
16
16
16
GRA GRA/WHT
BLK/BLU
19
18
28
Y
Y
16
CAVITY PLUG
BLK/RED 29 X
3146079
X
(2)
1 2 3 4 5 6
27
16 Y
RED/YEL
121110 9 8 7
22
16
Y
ORG/WHT
23
25
24
Y
16
Y
Y
16
RED/WHT 16
16 ORG
BLK/WHT BLK/YEL
26
Y
702-17 & 802-19 TRUCK SPREADER MOUNT KIT
6,'(9,(:
7,*+7(1++&6
817,/85(7+$1( 635,1*,6618*
7+(17,*+7(1
++&67851025(
Page 50
702-17 & 802-19 TRUCK SPREADER MOUNT KIT
,7(0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
3$57
130618
130779
130782
130784
130795
130796
130797
130798
130956
130957
351988
400116
400916
401108
401212
402512
405704
405708
405841.5
406481
407142
830310
830314
'(6&5,37,21
PLATE, SPREADER TRUCK MOUNT, 12" x 11"
802 MOUNTING TUBE SUPPORT, 4" x 10"
802 HOSE CLAMP, 3" x 9"
802 HOSE SUPPORT, 31"
MUD FLAP BRACKET, 3" x 23 3/4"
802 UHMW MOUNT PAD, 3/4"
802 WASHER, 1/2" x 1-1/16" x 3-1/2"
802 HOSE SUPPORT CLAMP, 4"
802 WASHER, 1/2" x 1-1/16" x 3"
PLATE, 1-3/4" x 4"LG
PIRANHA URETHANE STRIPPER SPRING
HEX SERRATED FLANGE NUT, 3/4"-10, #5 PLTD
HEX TWO-WAY LOCKNUT, 1"-8, #5 PLTD
HEX NYLOC NUT, 1/2"-13, #5 PLTD
HEX NYLOCKNUT, 3/4"-16
SAE FLAT WASHER, 3/4"
HHCS, 1/2"-13 x 1-3/4", #5 PLTD
HHCS, 1/2"-13 x 2 3/4", #5 PLTD
HHCS, 1" x 8-1/2", #5 PLTD
HHCS, 3/4"-10 x 2-1/2", #5 PLTD
CARRIAGE BOLT, 3/4" x 3", #5 PLTD
802 MOUNTING CROSSMEMBER W/A
802 URETHANE MOUNTING BRACKET W/A
Page 51
47<
6
2
3
2
4
2
2
4
2
2
2
16
2
7
32
32
4
3
2
32
16
4
2
702-17 & 802-19 TRUCK SPREADER
CONTROLLER & STAND
1 2
6
5
3
2 1
4
,7(0
1
2
3
4
5
6
3$57
400606
409543
452077
871087
871095
871103
'(6&5,37,21
HEX JAM NUT 3/8-16"
SQ HD SET SCREW CUP, 3/8" x 1"
CONTROLLER, 802 SPREADER
TURCK SCALE INDICATOR BASE W.A.
TRUCK SCALE INDICATOR MOUNT W.A.
INDICATOR EXTENSION TUBE W.A.
Page 52
47<
3
3
1
1
1
1
702-17 & 802-19 TRUCK SPREADER DECALS
8
1
2
5
12
9
,7(0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
3$57
440801
440826
440827
440833
440841
440844
440931
440939
440953
440955
440956
440965
441657
441663
3
4
13
6
14
7
11
'(6&5,37,21
DECAL, REDUCE ENGINE SPEED 4-1/4" x 7"
DECAL, DANGER: ROTATING DRIVE SHAFT
DECAL, DANGER: ROTATING AUGERS
DECAL, DANGER PINCH POINT 4" x 4"
DECAL, PATENT PENDING 5/8" x 5"
DECAL, MADE IN USA
DECAL, GREASE GUN DECAL, 10 HOURS
DECAL, ROTO-SPREAD
DECAL 802-19 (ROTO-SPREAD)
DECAL, USE E90W GEAR LUBE ONLY
DECAL, USE 10W HYD OIL, UNIV TO-4
DECAL, 702-17 (ROTO-SPREAD)
DECAL, WARNING ESCAPING HYD OIL
DECAL, WARNING DO NOT ATTACH PTO SHAFT
Page 53
10
47<
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement