G32D4 Full Size Digital / Gas Convection Oven on a

G32D4 Full Size Digital / Gas Convection Oven on a
G32D4 / P8M
Technical data sheet for
G32D4 ON THE P8M Prover/Holding Cabinet
Full Size Digital / Gas Convection Oven on a
8 Tray Manual / Electric Prover/Holding Cabinet
STANDARD FEATURES
• 4 460mm x 660mm / 18” x 26” full size sheet pan capacity
• 4 400mm x 600mm tray capacity (optional kit for P8M)
• 4 tray Oven / 8 tray Prover
• 735mm width
• Low unit height 1560mm
• Side hinged doors (standard LH hinge)
• Optional RH hinge (field convertible)
• Dual halogen lamps in Oven and Prover
• Prover with dual function Prove and Holding modes
OVEN
• 110mm tray spacing
• Electronic digital display time and temperature controls
• Manual mode and Program mode
• 20 programs with 3 stage cooking and stage end alarms
• Core Probe program cooking (optional Core Probe Kit)
• Moisture injection mode (5 levels) and manual injection
• Bi-directional reversing fan system
• Safe-Touch vented door
• Vitreous enamel oven chamber
• 35MJ/hr patented infrared burner system
• Plug-in continuous oven door seal
• 4 oven wire racks supplied
• 100% recyclable packaging
G32D4
Unit shall be a Moffat gas heated Turbofan convection oven. The oven shall have
a one piece vitreous enamel oven chamber, stainless top and sides and safe touch
vented easy clean side hinged door that offers field reversible hinging. Oven shall
have capacity for four full size sheet pans. The oven shall be controlled by an
electronic control having separate digital displays and adjusting knobs for time and
temperature functions. The oven control shall allow both manual and programmed
operating modes with programmable moisture injection and 3 stage cooking. A core
temperature probe M236060 is optional. The unit shall include dual halogen oven
lamps. Unit shall be supplied in 100% recyclable shipping packaging.
P8M
Unit shall be a Moffat electrically heated Turbofan Prover and Holding Cabinet.
The prover and holding cabinet shall have double skin construction with stainless
steel interior and exterior sides, front and top. Door shall be side hinged and field
reversible. Unit shall have capacity for up to 16 half size sheet pans or 8 full size
sheet pans.
A single speed fan shall gently and evenly circulate air around the cabinet. Cabinet
shall be controlled by a mechanical thermostat and humidity via a control of the
water tank. A thermometer shall indicate the cabinet temperature. Prover and
holding cabinet shall be mounted on castors, with two rigid castors at rear and two
swivel castors dual swivel and wheel lock and front. Prover and Holding Cabinets
shall be fitted with 10A cordsets. Unit shall be supplied in 100% recyclable shipping
packaging.
PROVER
• 76mm tray spacing
• Auto water fill system with optional integrated water filter kit
• Continuous door seal
• Low velocity circulation fan system
• Mechanical thermostat and humidity level control
• Cabinet temperature display thermometer
• 4 dia. 76mm castors with 2 front castors dual wheel and swivel lock, 2 rigid rear castors
• 100% recyclable packaging
ACCESSORIES
• Optional M236060 Core Temp Probe Kit
• 400mm x 600mm tray racking kit for P8M
• Optional 3M Cuno water filter kit complete with cartridge and connection fittings
• Installs in pre-fitted rear housing of cabinet for flush rear installation
G32D4 / P8M
G32D4 Full Size Digital / Gas
Convection Oven
P8M Full Size Manual / Electric
Prover/Holding Cabinet
SPECIFICATIONS
Gas Requirements - Oven (G32D4)
35MJ/hr burner rating
Natural, LPG models
Unit supplied complete with gas type conversion kit
CONSTRUCTION - Oven (G32D4)
Vitreous enamel fully welded oven chamber
Stainless steel front, sides and top exterior
Stainless steel frame side hinged door
5mm thick door inner and outer glass
Stainless steel control panel
Aluminised coated steel base and rear panels
Gas Connection - Oven (G32D4)
½” BSPT male
Prover (P8M)
230-240V, 50Hz, 1P+N+E, 1.5kW, 6.3A
10A cordset fitted
Water Requirements
Cold water connection ¾” BSP male
80psi maximum inlet pressure / 20psi minimum inlet pressure
Connection to oven optional
CONTROLS - Oven (G32D4)
Electronic controls with digital time and temperature display,
Manual or Program modes
Large 20mm high LED displays
Two individual time and temperature setting control knobs
ON/OFF key
Oven Lights key
Timer Start/Stop key
Moisture Injection key (5 levels)
Programs select key
Actual temperature display key
Adjustable buzzer/alarm volume
Thermostat range 50-260°C
Timer range from 180 minute in countdown mode /
999 minute in count-up mode
Direct burner ignition control flame failure safety control
Optional Core Probe temperature range 50-90°C
Over-temperature safety cut-out
External Dimensions
Width 735mm
Height 1715mm
Depth810mm
Packing Data
Oven (G32D4)
131kg
0.71m3
Width 760mm
Height 1010mm
Depth
925mm SURFACES SURFACES
Rear75mm
75mm
LH Side
50mm
50mm
RH Side* 75mm
75mm
* For fixed installations a minimum of 500mm is required
for service
CLEARANCE FROM SOURCES OF HEAT
A minimum distance of 300mm from the appliance sides
is required
810 mm / 317 8"
GAS
FLUE
Proofer (P8M)
95.3kg
0.76m3
Width 760mm
Height1080mm
Depth
925mm
INSTALLATION CLEARANCES
NON-COMBUSTIBLECOMBUSTIBLE
CLEANING
Stainless steel top and side exterior panels
Vitreous enamel oven chamber
Fully removable stainless steel oven and prover side racks
Removable stainless steel oven fan baffle
Easy clean door system with hinge out door inner glass (no
tools required)
Removable plug-in oven door seal (no tools required)
82 mm / 31 4"
310 mm / 121 4"
WATER INLET
GAS
FLUE
New South Wales
Telephone 02-8833 4111
[email protected]
South Australia
Telephone 03-9518 3888
[email protected]
Western Australia
Telephone 08-9202 6820
[email protected]
Proofer (P8M)
77.5kg
Victoria/Tasmania
740 Springvale Road
Mulgrave, Victoria 3170
Telephone 03-9518 3888
Facsimile 03-9518 3833
[email protected]
Queensland
Telephone 07-3630 8600
[email protected]
Nett Weight
Oven (G32D4)
113kg
CONTROLS - Prover (P8M)
Off / Prove / Holding mode selector switch
Mechanical thermostat 20-85°C
Humidity level control
Cabinet temperature thermometer
Auto-fill water system standard
735 mm / 287 8"
Australia
Moffat Pty Limited
Electrical Requirements
Oven (G32D4)
230-240V, 50Hz, 1P+N+E, 0.5A
10A cordset fitted
CONSTRUCTION - Prover (P8M)
304 stainless steel interior cabinet
Stainless steel front, sides and top exterior
Stainless steel interior side racks
Stainless steel frame side hinged door
5mm thick door glass
Stainless steel control panel
Aluminised coated steel base and rear panels
Australia
www.moffat.com.au
New Zealand
www.moffat.co.nz
www.turbofanoven.com
92 mm / 35 8"
87 mm / 33 8"
35 mm / 13 8"
25 mm / 1"
100 mm / 37 8"
New Zealand
Moffat Limited
Christchurch
45 Illinois Drive
Izone Business Hub
Rolleston 7675
Telephone +64 3-983 6600
Facsimile +64 3-983 6660
[email protected]
Auckland
Telephone 09-574 3150
[email protected]
ISO9001
Quality
Management
Standard
Designed and manufactured by
ELECTRICAL
ENTRY
1725 mm / 677 8"
GAS
ENTRY
283 mm / 111 8"
120 mm / 43 4"
ELECTRICAL
ENTRY
575 mm / 225 8"
1132 mm / 441 2"
1063 mm / 417 8"
969 mm / 381 8"
820 mm / 321 4"
WATER INLET
ISO9001
All Turbofan products are designed and
manufactured by Moffat using the
internationally recognised ISO9001
quality management system, covering
design, manufacture and final inspection,
ensuring consistent high quality at all times.
In line with policy to continually develop
and improve its products, Moffat Limited
reserves the right to change specifications
and design without notice.
© Copyright Moffat Ltd
AN.TFN.S.1501
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement