INSTALLATION
REAR ACCESSORY LIGHT ADAPTER for 01-10 GL 1800
CUSTOMER SERVICE
PARTS INCLUDED
1
1
1
877.370.3604 (toll free)
Plug & Play Rear Accessory Wiring Adapter
Dielectric Grease Pack
Installation Instructions
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND NOTICES REGARDING THE USE
AND CARE OF THIS PRODUCT.
THIS INDICATION ALERTS YOU TO THE FACT THAT
IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality.
IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY,
PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE
INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF
THE IMPORTANT INFORMATION CONTAINED IN THEM.
TOOLS SUGGESTED
Set of Metric Hex Wrenches
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
NOTE: Only one Rear Accessory Harness
Adapter is required for all future
6-Pin style Kuryakyn accessories
installed on the motorcycle.
PIC 1
OLDER MODELS HAVE FIFTH
FASTENER BEHIND HERE
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
Remove four fasteners that secure the
rear license plate panel. (Older bikes
will have five. The fifth will be behind
the license plate). PIC 1.
©2005 Küryakyn USA® All Rights
reserved.
REMOVE THESE FOUR FASTENERS
-cont.-
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
ABOUT OUR CATALOG
Kuryakyn products released after
1-01-12. For accessories requiring
this adapter, see
www.kuryakyn.com.
3241-21GL-0412
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
NOTE: This Adapter is only required for
STEP 2
3241
STEP 3
Gently pull off the back panel exposing the wiring harness. (Red and Blue plugs) PIC 2
PIC 2
Kuryakyn recommends the use of dielectric grease on
electrical connections.
NOTE: If you already have Kuryakyn Rear Accessory lights or Kuryakyn
Plug and Play Trailer Harness on the back of your motorcycle,
unplug either end of the current wiring adapter installed and plug
the new Rear Accessory Light Adapter in-line with it for the
following Steps. PIC 3
STEP 4
On the bike, disconnect the red plug that has an orange wire. Take the
supplied harness, connect the male and female plug (3-wire plug with a
single ORANGE wire running to it), into the disconnected stock red male
and female plugs. PIC 4 The sub harness acts like a t-harness and will go
between the stock red plugs.
STEP 5
On the bike, disconnect the blue connector that has a light blue wire. Take
the supplied harness, connect the male and female plug (3-wire plug with
the RED and BLUE wires) into the disconnected stock blue male and
female plugs. PIC 4 The sub harness acts like a t-harness and will go
between the stock blue plugs.
STEP 6
Locate the blue connecter on the bike that has the green wires. Disconnect
it and place the two-pin connector with the BLACK and WHITE wires in to
the male and female ends. PIC 4 The sub harness acts like a t-harness and
will go between the stock blue plugs.
STEP 7
You should have one six-pin connector left. This connection will be used to
supply the power to the accessory lighting. PIC 4
STEP 8
Turn the bike on and check all lights function correctly.
PIC 3
ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE.
VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS. A LIGHT
MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY.
STEP 9
Use the included cable ties to secure the
wiring out of harms way. Replace the
rear fender panel.
Secure all wiring away from
any moving parts, pinch points
or extreme heat. Küryakyn
WILL NOT issue a warranty on
any electrical component that
fails due to pinched, crimped,
broken, abraded, melted or
frayed wires.
It is the installer’s
responsibility to ensure that all
of the fasteners (including
pre-assembled) are tightened
before operation of the
motorcycle. Küryakyn will not
issue a warranty on
components lost due to
improper installation. Periodic
maintenance may be required.
PIC 4
ACCESSORY
PLUG
CONNECT
TO BLUE
MALE AND
FEMALE
CONNECT TO RED
MALE AND FEMALE
PLUGS
BLUE AND
REDWIRE
SINGLE ORANGE
WIRE
BLACK AND
WHITE WIRE
CONNECT TO BLUE
CONNECTERS WITH
GREEN WIRES
PAGE
2
Ride On!
REAR ACCESSORY LIGHT ADAPTER
INSTALLATION
">
