- Computers & electronics
- Audio & home theatre
- MP3/MP4 players
- Mitsubishi
- MZ607411EX
- Instruction manual
Mitsubishi MZ607411EX Instruction manual
Add to my manuals26 Pages
Mitsubishi MZ607411EX is an iPod adapter that allows you to connect your iPod to your car's audio system. It features a dock connector that you can run into your glove compartment, and a 13P DIN cable that you can connect to the back of your audio space. The adapter also includes double-coated tape for mounting the main unit, and a power cord with a fuse that you can connect to your vehicle's BATT terminal. With this adapter, you can control your iPod through your head unit and enjoy your music while driving.
advertisement
Components
(1) Adapter main uni t (2) Double-coated tape (2 pcs.
) (3) Power cord (4) Instruction manual
3 Positioning the various cords
iPod adapter
MODEL
MZ607411EX
( V-900IP-U )
INSTALLATION MANUAL
Remove the audio, the floor console,the side panel,etc.
Existing harness
WARNING
(5) Installation instructions
Run the 13P DIN cable to the back of the audio space.
component will be installed, also run the (3) power cord together with the DIN cable.
The slack harness should be bundled up and attached to the existing harness in the back of the audio space in a way which will not result in noise.
Run the dock connector into the glove compartment and run it so that about 20cm can be pulled out.
Remove the glove compartment and trim.
Dock connector
• Read these installation instructions thoroughly prior to starting installation work.
• Wiring should be performed after disconnecting the negative terminal of the battery.
Otherwise, electric shock or physical injury may occer.
• This equipment is only for vehicles equipped with 12V DC negative ground systems.
Do not install it in any vehicle equipped with a 24V system, such as a large truck or diesel powered automobile equipped for cold regions. Such usage causes danger of fi re.
• All cords should be kept together to avoid interference with driving operations. It is dangerous if they wind around the steering column, gear shift lever or brake pedal.
• If any cord comes in contact with a burr (sharp projection formed during the manufacture of parts) or any other sharp object, protect the cord by covering with tape to avoid damage. Any damage to the covering may be a cause of fi re or electric shock.
• Never install in a manner that blocks front visibility, interferes with normal driving operations of the steering wheel, gear shift lever or brake pedal or creates a danger to any passenger in the case of a sudden stop. It may be the cause of a traffi c accident or injury.
• Be sure to use all the accessory components as instructed and attach them securely. Never use a part other than that specifi ed. Use of such a part may cause danger of damage to the internal components of the unit or loosening or detachment of components.
• When attaching the ground to bolts or nuts attached to the vehicle, never use those of any safety related component such as the steering, brake system or fuel tank.
Such usage may cause accidents.
• After completion of the wiring and installation work, ensure that all electric components, such as the brake system, lights, horn and turn signal lights operate normally as before the installation. If operation is not normal, fi nd the cause by checking the wiring to make sure it is proper. Use with unknown problems may be the cause of fi re, electric shock and accidents.
• Never disassemble or modify the unit. It may be the cause of accident, fi re or electric shock.
• If any abnormality, such as penetration by any foreign material, splashing, smoking or if normal odors occur, stop use immediately and contact the dealer. Continuing use may be the cause of accidents, fi re or electric shock.
Screwdriver
Needed Tools
Tape measure
General main points regarding installation
Ornament Remover
1 Setting of adapter main unit
The iPod adapter must be set ahead of time according to the system to which it will be connected. Set the adapter main unit referring to the initial settings on the back of this sheet.
2 Mounting adapter main unit
(1) Adapter main unit
(2)Double-coated tape (2 pcs.) mb303
Top surface
Bottom surface
Mounting surface
Label
Caution
Electrical Tape
Stick the (2) double-coated tape on the (1) adapter main unit and stick them to the mounting surface.
Check
Stick the (2) double-coated tape to the bottom surface of the (1) adapter main unit (the surface without the label). If the (2) double-coated tape will be stuck on the top surface, position the tapes so that they do not cover the label.
* Wipe the area to which the tapes will be stuck on clean and stick the tapes on securely.
it in the glove compartment.
(1) Adapter main unit
Check
4 About connections
The main points of connections will be different for each system. Please refer to "Main Points Regarding Connection" on the back of this sheet.
Check
5 Operation check
1)Connect the iPod.
2)Operate the head unit to select the iPod.
3)Operate the head unit and check that the iPod sound is being
out-put.
*
If an iPod is not available, perform the following simple check.
1)Operate the head unit and select the iPod.
2)Check that the audio display shows the eject status display ("EJ", etc.)
If operation is not normal, recheck all connections and recheck the settings
of the adapter main unit.
Check
'06.05 I.P N871L65482 (1/2) Printed in Japan.
06.5.22 4:39:33 PM iPod_englishA3_A.indd 1
Main Points Regarding Connection
When connecting only the iPod adapter
Head unit
13P iPod
Initial settings
Depending on the head unit that will be connected, it may be necessary to change the settings of this adapter. The setting switches are on the side of the adapter. Set the switches as shown below before installing the unit. At the time of shipment from the factory, all switches are set to ON.
Name card
Switch section Switch
ONside O
N
↑ 1 2 3 4
OFFside
Dock connector
Not used
(1)Adapter main unit
13P
13P DIN connector
Can be used to connect
An existing Satellite Radio(SIRIUS TM ) .
• SIRIUS Satellite Inc. “SIRIUS” and related marks are trademarks of SIRIUS Satellite Radio Inc.
When connecting the iPod adapter and a 1DIN size add-on (6-disc CD changer) simultaneously
Setting information
Details
(The head unit code is indicated on top or bottom surface.)
Setting according to connected optional equipment
Head unit code.
•MN141490 ( MONTERO,LANCER,LANCER SPORTBACK )
•MN141494 ( ECLIPSE,ECLIPSE SPYDER (~’05) )
•MN141488 ( MONTERO,MONTERO SPORT, OUTLANDER )
•MN587385 ( MONTERO SPORT,OUTLANDER )
•MN141496 ( GALANT )
•MR306775 ( GALANT )
•8701A011 ( ECLIPSE (’06~),ECRIPSE SPYDER(’07~) )
•8701A032 ( OUTLANDER )
•8701A045 ( ENDEAVOR,GALANT,ECLIPSE(’06~) )
•MN141259 ( ENDEAVOR )
Mode setting
Album mode:Selects by the unit of Album and Play list.
1
ON ON -
-
Switch settings
2 3 4
ON -
Head unit
Intermediate connector
(MZ598118EX; sold separately)
13P 20P
Use tape, etc. to protect the terminals.
(3)Power cord
Fuse
Connect to BATT terminal.
(1)Adapter main unit
6-disc CD changer iPod
Dock connector
13P
Scan function setting
All songs mode:Selects by the unit of 100songs from all songs in iPod.The listed head units be used only in All songs mode.
•MN141490 ( MONTERO,LANCER,LANCER SPORTBACK )
•MN141494 ( ECLIPSE,ECLIPSE SPYDER (~’05) )
•MN141488 ( MONTERO,MONTERO SPORT, OUTLANDER )
•MR587385 ( MONTERO SPORT,OUTLANDER )
•MN141496 ( GALANT )
•MR306775 ( GALANT )
-
When the head unit is equipped with a CD Scan function -
When the head unit is not equipped with a CD Scan function and
the Scan function will be used. * 1
1 The functions of the RPT or RPT/RDM buttons will be changed to Scan. As a result, RPT or RPT/RDM function cannot be used.
-
OFF -
ON
OFF
Vehicle-side 14P connector iPod_englishA3_A.indd 2 06.5.22 4:39:34 PM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project