Acer | S5201 | User`s guide | Acer S5201 User`s guide

Acer Projector
P5206/N216/PN-X14/S5201/T111/PSX11/S5201B/T111E/PS-X11K/
S5301WB/T121E/PS-W11K Series
User's Guide
Copyright © 2010. Acer Incorporated.
All Rights Reserved.
Acer Projector P5206/N216/PN-X14/S5201/T111/PS-X11/S5201B/T111E/PS-X11K/S5301WB/T121E/
PS-W11K Series User's Guide
Original Issue: 12/2010
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Acer Projector P5206/N216/PN-X14/S5201/T111/PS-X11/S5201B/T111E/PS-X11K/S5301WB/T121E/
PS-W11K Series
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to
their respective companies.
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC."
iii
Information for Your Safety and
Comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•
•
•
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
•
•
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•
•
•
•
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.6 meters (15 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
•
•
Do not look into the projector's lens when the lamp is on. The bright light
may hurt your eyes.
Turn on the projector first and then signal sources.
Do not place the product in the following environments:
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector are necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shorten the life span and darken the image.
Locations near fire alarms.
•
•
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
•
•
•
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
vi
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, please ensure the projector completes
its cooling cycle before disconnecting power.
Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to stop
before turning main power off.
Do not touch the air outlet grille and bottom plate which become hot.
Clean the air filter frequently. The temperature inside may rise and cause
damage when the filter/ventilation slots are clogged with dirt or dust.
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when warning messages display.
When changing the lamp, please allow the projector to cool down, and
follow all changing instructions.
Reset the "Lamp Hour Reset" function from the Onscreen Display
"Management" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
vii
Caution for Listening
To protect your hearing, follow these instructions.
•
•
•
•
•
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit http://www.acer-group.com/public/
Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
"Lamp(s) contain Mercury,
Dispose Properly."
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
viii
First Thing First
Usage Notes
Do:
•
Turn off the product before cleaning.
•
Use a soft cloth moistened with mild detergent to clean the display
housing.
•
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•
Block the slots and openings on the projector provided for ventilation.
•
Use abrasive cleaners, waxes or solvents to clean the unit.
•
Use under the following conditions:
•
•
•
•
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place in direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•
•
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•
•
Please do not open or disassemble the product as this may cause electric shock.
•
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
•
Reset the "Lamp Hour Reset" function from the Onscreen Display "Management"
menu after replacing the lamp module.
•
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•
•
•
Turn on the projector first and then the signal sources.
When changing the lamp, please allow the projector to cool down, and follow all
changing instructions.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
First Thing First
iii
viii
Usage Notes
viii
Precautions
viii
Introduction
1
Product Features
1
Package Overview
2
Projector Overview
3
Projector Outlook
3
Control Panel
4
Remote Control Layout
5
Getting Started
Connecting the Projector
Turning the Projector On/Off
7
7
9
Turning On the Projector
9
Turning Off the Projector
10
Adjusting the Projected Image
11
Adjusting the Height of the Projected Image
11
How to Optimize Image Size and Distance
12
How to Get a Preferred Image Size by Adjusting
Distance and Zoom
15
User Controls
18
Installation Menu
18
Acer Empowering Technology
19
Onscreen Display (OSD) Menus
20
Color
21
Image
23
Setting
25
Management
31
Audio
32
Timer
33
Language
33
Appendices
34
Contents
Information for Your Safety and Comfort
Troubleshooting
34
LED & Alarm Definition Listing
38
Replacing the Lamp
39
Ceiling Mount Installation
40
Specifications
43
Compatibility Modes
46
Regulations and safety notices
50
1
Product Features
This product is a single-chip DLP® projector, including the following
outstanding features:
•
DLP® technology
•
P5206/N216/PN-X14/S5201/T111/PS-X11/S5201B/T111E/PS-X11K: Native 1024
x 768 XGA resolution
Auto / 4:3 / 16:9 aspect ratio supported
S5301WB/T121E/PS-W11K: Native 1280 x 800 WXGA resolution
Auto / Full / 4:3 / 16:9 / L.Box aspect ratio supported
•
Acer ColorBoost technology delivers vivid, life-like images
•
High brightness and contrast ratio
•
Versatile display modes enable optimum performance in any situation
•
NTSC/PAL/SECAM compatible and HDTV (720p, 1080i, 1080p) supported
•
Lower power consumption and economy (ECO) mode extends lamp life
•
Acer EcoProjeciton Technology delivers Intelligent power management
approach and physical efficiency improvement
•
Empowering Key reveals Acer Empowering Technology functions (Acer
eView, eTimer, eOpening, ePower Management) for easy adjustment of
settings
•
Advanced keystone correction delivers optimum presentations
•
Multi-language Onscreen Display (OSD) menus
•
Full-function remote control
•
P5206/N216/PN-X14: Manual focus projection lens zooms up to 1.3X
•
2X digital zoom and pan move function
•
Microsoft® Windows® 2000, XP, 7, Vista® OS compliant
•
LAN settings enable remote management of projectors via a web browser
•
Enables projecting 3D content via DLP Link technology
•
Acer Color Safe technology ensures consistent color rendition over time
•
Smart detection delivers quick, intelligent source detection
English
Introduction
English
2
Package Overview
This projector comes with all the items shown below. Check to make sure you
have them all. Contact your dealer immediately if any thing is missing.
Projector with lens cap
Power cord
VGA cable
Composite video cable
Security card
User’s guide (CD-ROM)
Acer Projector
Quick Start Guide
Remote control
Quick start guide
Battery x 2
Acer Projector Gateway
Quick Start Guide
Carrying case
Dust filter
(Optional)
Acer Projector Gateway (CDROM) (for S5201B/T111E/PSX11K/S5301WB/T121E/PSW11K)
Acer Projector Gateway
quick start guide (for
S5201B/T111E/PS-X11K/
S5301WB/T121E/PS-W11K)
3
English
Projector Overview
Projector Outlook
Front / upper side
(S5201/T111/PS-X11/S5201B/T111E/
PS-X11K/S5301WB/T121E/PS-W11K)
5
1
(P5206/N216/PN-X14)
5
1
6
7
2
3
7
2
3
8
4
8
4
#
Description
#
Description
1
Power key and Power indicator
LED
5
Control panel
2
Projection lens
6
Zoom ring
3
Elevator button
7
Focus ring
4
Lens cap
8
Remote control receiver
Rear side
(P5206/N216/PN-X14/S5201/T111/
PS-X11/)
(S5201B/T111E/PS-X11K/S5301WB/
T121E/PS-W11K)
1 23 4
56
7
8
9 10 11
12 3 4
6
7
8
9 10 11
DC OUT
12 13
14
15
12
#
Description
1 Remote control receiver
2 USB connector (Type mini B)
3 LAN (RJ45 port for 10/100M
Ethernet)
4 HDMI connector
5 USB connector (Type A)
6 RS232 connector
7 Monitor loop-through output
connector
8 PC analog signal/HDTV/component
video input connector (VGA IN 1/
VGA IN 2)
#
Description
9 S-Video input connector/
Composite video input connector
10 Audio input connector/
Audio output connector
11 Microphone input connector
12 Tilt adjusting wheel
13 Power socket
14 12V DC output connector
15 Kensington™ lock port
English
4
Control Panel
1
2
3
7
8
4
9
5
10
6
4
#
Function
Description
1
LAMP
2
POWER
Power indicator LED
3
Power key
Refer to the "Turning the Projector On/
Off" section.
4
Keystone
Adjusts image distortion caused by tilting
projection (±40 degrees).
5
MENU
•
Launches the Onscreen Display (OSD)
menu, returns to the previous step for
the OSD menu operation or exits the
OSD menu.
•
Confirms your selection of items.
6
RESYNC
Automatically synchronizes the projector
to the input source.
7
TEMP
Temp indicator LED
8
Empowering key
Enables unique Acer functions: eView,
eTimer, eOpening, ePower Management.
9
Four directional select keys
Selects items or makes adjustments to your
selection.
10 SOURCE
Lamp indicator LED
Chooses RGB, component video, S-Video,
composite video, HDMI™ or HDTV source.
5
#
Function
English
Remote Control Layout
Description
1
Infrared
transmitter
Sends signals to the projector.
2
POWER
Refer to the "Turning the Projector On/Off" section.
3
FREEZE
To pause the screen image.
4
RESYNC
Automatically synchronizes the projector to the input
source.
5
BACK
6
Goes back to the previous selection.
Keystone
Four
directional
select keys
7
Mouse
button
8
Four
directional
select pad
9
VOL +/-
10 Empowering key
Adjusts image distortion caused by tilting projection
(±40 degrees).
Selects items or makes adjustments to your selection.
This function is not available with the projector.
Selects the media files in four directions.
Increases/decreases the volume.
Enables unique Acer functions: eView, eTimer,
eOpening, ePower Management.
English
6
#
11
Function
Rewind
Play/Pause
Stop
Fast-forward
Description
Rewinds/Plays/Pauses/Stops/Fast-forwards the playing
media files.
12 VGA
To change source to VGA. This connector supports
analog RGB, YPbPr (480p/576p/720p/1080i/1080p),
and YCbCr (480i/576i).
13 COMPONENT
To change source to Component video. This
connector supports YPbPr.
14 SD/USB A
To change source to SD/USB A. This projector only
supports files in JPEG format. (for S5201B/T111E/PSX11K/S5301WB/T121E/PS-W11K)
15 HDMI™/DVI
To change source to HDMI™/DVI (for the model with
HDMI™/DVI connector).
16 Keypad 0~9
Press "0~9" to input a password in the "Setting >
Security" OSD.
17 Laser pointer
window
Shines the laser point light when the Laser button is
pressed.
18 HIDE
Press "HIDE" to hide screen image; press again to
display the image.
19 ASPECT RATIO
To choose the desired aspect ratio (Auto/4:3/16:9).
20 SOURCE
Chooses RGB, component video, S-Video, composite
video, HDMI™, or HDTV source.
21 ZOOM
Zooms the projector display in or out.
22 ENTER
Confirms your selection of items.
23
Emits visible laser pointer light for presentation
purposes. This function is not available for the
projectors sold in the Japanese market.
Laser
24 MENU
Launches the Onscreen Display (OSD) menu, returns
to the previous step for the OSD menu operation or
exits the OSD menu.
25 PAGE ^/v
For computer mode only. Use the button to select the
next or previous page. This function is only available
when connected to a computer via a USB cable.
26 S-VIDEO
To change source to S-Video.
27 VIDEO
To change source to Composite video.
28 USB B
To change source to USB B.
29 LAN/WiFi
To change source to LAN/WiFi. (for LAN/wireless
compatible models)
7
English
Getting Started
Connecting the Projector
•
P5206/N216/PN-X14/S5201/T111/PS-X11
VGA
11
RS232
5
DVD player, Set-top box,
HDTV receiver
USB
Display
D-Sub
10
2
8
9
W R
D-Sub
RS232
R B G
10
S-Video/Video Output
Y
R B G
7
Speakers
6
3
5
2
Microphone
D-Sub
HDTV adapter
D-Sub
USB
1
Screen
MIC.
DC OUT
12
Y
#
Description
#
7
Description
1
Power cord
RS232 cable
2
VGA cable
8
HDMI cable
3
VGA to component video/HDTV
adapter
9
3 RCA component cable
4
Composite video cable
10 RJ45 cable
5
Audio cable
11 USB cable
6
S-Video cable
12 12V DC cable
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
4
•
S5201B/T111E/PS-X11K/S5301WB/T121E/PS-W11K
VGA
5
11
DVD player, Set-top box,
HDTV receiver
USB
Display
RS232
D-Sub
10
2
8
9
W R
Speakers
D-Sub
RS232
R B G
10
S-Video/Video Output
Y
R B G
7
6
3
5
2
Microphone
1
D-Sub
HDTV adapter
D-Sub
USB
English
8
Screen
MIC.
DC OUT
13
12
Y
#
Description
#
4
Description
1
Power cord
8
HDMI cable
2
VGA cable
9
3 RCA component cable
3
VGA to component video/HDTV
adapter
10
RJ45 cable
4
Composite video cable
11
USB cable
5
Audio cable
12*
USB storage device/USB Wifi adapter
(Optional)
6
S-Video cable
13
12V DC cable
7
RS232 cable
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: "*" USB drive limitation, do not support power.
9
English
Turning the Projector On/Off
Turning On the Projector
1
Remove the lens cap.
2
Ensure that the power cord and signal cable are securely connected.
The Power LED will light red.
3
Turn on the projector by pressing
(POWER) on the control panel or
remote control, and the Power indicator LED will turn blue.
4
Turn on your source (computer, notebook, video player, etc.). The
projector will detect your source automatically.
•
If the screen displays "No Signal", please make sure the signal cables
are securely connected.
•
If you connect to multiple sources at the same time, use "SOURCE" on
the control panel or remote control, or the direct source key on the
remote control to switch between inputs.
2&3
1
Lens cap
2&3
1
Lens cap
English
10
Turning Off the Projector
1
To turn the projector off, press the power button. This message
appears:
"Please press the power button again to complete the shutdown process."
Press the power button again.
2
The LED power indicator will turn RED and blink rapidly after the
projector is turned off, and the fan(s) will continue to operate for
about 2 minutes to ensure that the system cools properly.
3
As long as the power cord remains plugged in, you can press the
power button to turn the projector immediately back on anytime
during the 2-minute shutdown process.
4
Once the system has finished cooling, the LED power indicator will
stop blinking and turn solid red to indicate standby mode.
5
It is now safe to unplug the power cord.
Warning indicators:
•
"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp will automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.
•
"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and
the LED lamp indicator turns solid red, contact your local
reseller or service center.
11
Adjusting the Height of the Projected Image
The projector is equipped with an elevator foot for adjusting the image height.
To raise the image:
1
Press the elevator button.
2
Raise the image to the desired height angle, then release the button
to lock the elevator foot into position.
3
Use Tilt adjusting wheel to fine-tune the display angle.
To lower the image:
1
Press the elevator button.
2
Lower the image to the desired height angle, then release the button
to lock the elevator foot into position.
3
Use Tilt adjusting wheel to fine-tune the display angle.
1
Elevator
button
3
Tilt adjusting wheel
2
Elevator foot
3
Tilt adjusting wheel
English
Adjusting the Projected Image
English
12
How to Optimize Image Size and Distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen.
•
P5206/N216/PN-X14
If the projector is 3 m from the screen, good image quality is possible for image
sizes between 75" and 98".
Note: Remind as below figure, the space of 161 cm height is
required when the projector is located at 3 m distance.
Ma x
scre
Min
en s
iz
scre
e
en s
iz
B 98"
e
75"
Height:
126 cm
Height:
161 cm
From
base to
top of
image
C
A
3m
Desired distance
Minimum Screen Size (Min zoom)
Maximum Screen Size (Max zoom)
Desired
From base to
From base to
Distance Diagonal
Diagonal
top of image
top of image
(m)
(inch) W (cm) x H (cm)
(inch) W (cm) x H (cm)
(cm)
(cm)
<A>
<B>
<B>
<C>
<C>
1
25
51 x 38
41
33
66 x 50
54
1.5
38
76 x 57
62
49
99 x 75
80
106
2
50
102 x 76
82
65
132 x 99
2.5
63
127 x 95
103
81
166 x 124
133
3
75
152 x 114
123
98
199 x 149
161
3.5
88
178 x 133
144
114
232 x 174
187
4
100
203 x 152
164
130
265 x 199
213
4.5
113
228 x 171
185
147
298 x 224
241
5
125
254 x 190
205
163
331 x 248
267
6
150
305 x 228
246
196
397 x 298
321
7
175
355 x 266
287
228
464 x 348
374
8
201
406 x 305
329
261
530 x 397
428
9
226
457 x 343
370
293
596 x 447
480
10
251
508 x 381
411
326
662 x 497
534
11
276
558 x 419
452
359
728 x 546
588
12
301
609 x 457
493
391
795 x 596
641
Zoom Ratio: 1.3 x
13
S5201/T111/PS-X11/S5201B/T111E/PS-X11K
If the projector is 2 m from the screen, good image quality is possible for image
sizes around 161".
Note: Remind as below figure, the space of 320 cm height is
required when located at 2 m distance.
161"
B
Height:
320 cm
From
base to
top of
image
2m
Desired distance
A
Screen Size
Desired
From base to
Distance Diagonal
top of image
(m)
(inch) W (cm) x H (cm)
(cm)
<A>
<B>
<C>
0.5
40
82 x 61
80
0.8
65
131 x 98
128
1.1
89
180 x 135
176
1.4
113
230 x 172
224
1.7
137
279 x 209
272
2
161
328 x 246
320
2.3
186
377 x 283
368
2.6
210
426 x 320
416
2.9
234
475 x 357
464
3.2
258
525 x 393
511
3.7
299
607 x 455
591
Zoom Ratio: 1.0 x
C
English
•
English
14
•
S5301WB/T121E/PS-W11K
If the projector is 2 m from the screen, good image quality is possible for image
sizes around 189".
Note: Remind as below figure, the space of 281 cm height is
required when located at 2 m distance.
189"
B
Height:
281 cm
From
base to
top of
image
2m
Desired distance
A
Screen Size
Desired
From base to
Distance Diagonal
top of image
(m)
(inch) W (cm) x H (cm)
(cm)
<A>
<B>
<C>
0.5
47
102 x 64
70
0.6
57
122 x 77
84
0.7
66
143 x 89
98
0.8
76
163 x 102
112
0.9
85
184 x 115
126
1
95
204 x 128
140
1.5
142
306 x 191
210
2
189
408 x 255
281
2.5
237
510 x 319
351
3
284
612 x 383
421
3.5
332
714 x 446
491
Zoom Ratio: 1.0 x
C
15
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring.
•
P5206/N216/PN-X14
To obtain an image size of 50" set the projector at a distance between 1.5 m
and 2.0 m from the screen and adjust the zoom level accordingly.
A
D
50"
Desired
image size
1.5 m
2.0 m
Height:
82 cm
From base
to top of
image
B
Desired distance
C
Desired Image Size
Distance (m)
Top (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image < D >
1.2
49
81 x 61
1.2
1.6
66
102 x 76
1.5
2.0
82
60
122 x 91
1.8
2.4
98
70
142 x 107
2.1
2.8
115
80
163 x 122
2.5
3.2
131
90
183 x 137
2.8
3.6
147
100
203 x 152
3.1
4.0
164
120
244 x 183
3.7
4.8
197
150
305 x 229
4.6
6.0
246
180
366 x 274
5.5
7.2
295
200
406 x 305
6.1
8.0
328
250
508 x 381
7.7
10.0
410
300
610 x 457
9.2
Diagonal (inch)
<A>
W (cm) x H (cm)
30
61 x 46
40
50
Zoom Ratio: 1.3 x
491
English
How to Get a Preferred Image Size by Adjusting
Distance and Zoom
English
16
•
S5201/T111/PS-X11/S5201B/T111E/PS-X11K
To obtain an image size of 50" set the projector at a distance 0.6 m from the
screen.
A
50"
Desired
image size
D
Height:
99 cm
From
base to
top of
image
B& C
0.6 m
Desired distance
Desired Image Size
Diagonal (inch)
<A>
Distance (m)
Top (cm)
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image < D >
30
61 x 46
0.4
0.4
59
40
81 x 61
0.5
0.5
79
50
102 x 76
0.6
0.6
99
60
122 x 91
0.7
0.7
119
70
142 x 107
0.9
0.9
139
80
163 x 122
1.0
1.0
158
90
183 x 137
1.1
1.1
178
100
203 x 152
1.2
1.2
198
120
244 x 183
1.5
1.5
238
150
305 x 229
1.9
1.9
297
180
366 x 274
2.2
2.2
357
200
406 x 305
2.5
2.5
396
250
508 x 381
3.1
3.1
495
300
610 x 457
3.7
3.7
594
Zoom Ratio: 1.0 x
17
S5301WB/T121E/PS-W11K
To obtain an image size of 50" set the projector at a distance 0.5 m from the
screen.
A
50"
Desired
image size
D
Height:
74 cm
From
base to
top of
image
B& C
0.5 m
Desired distance
Desired Image Size
Diagonal (inch)
<A>
Distance (m)
Top (cm)
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image < D >
30
65 x 40
0.3
0.3
44
40
86 x 54
0.4
0.4
59
50
108 x 67
0.5
0.5
74
60
129 x 81
0.6
0.6
89
70
151 x 94
0.7
0.7
104
80
172 x 108
0.8
0.8
118
90
194 x 121
0.9
0.9
133
100
215 x 135
1.1
1.1
148
120
258 x 162
1.3
1.3
178
150
323 x 202
1.6
1.6
222
180
388 x 242
1.9
1.9
267
200
431 x 269
2.1
2.1
296
250
538 x 337
2.6
2.6
370
300
646 x 404
3.2
3.2
444
Zoom Ratio: 1.0 x
English
•
English
18
User Controls
Installation Menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No
signal input" is displayed on the screen.
1
Turn on the projector by pressing
remote control.
2
Press "MENU" on the control panel or remote control to launch the
OSD for projector installation and maintenance.
3
The background pattern acts as a guide to adjust the calibration and
alignment settings, such as screen size and distance, focus and more.
4
(POWER) on the control panel or
The Installation menu includes the following options:
•
Projection method
•
Menu location
•
Keystone settings
•
Language settings
•
LAN settings
•
Reset to factory default functions
Use the up and down arrow keys to select an option, the left and right arrow keys to
adjust selected option settings, and the right arrow key to enter a submenu for
feature setting. The new settings will be saved automatically upon exiting the menu.
5
Press "MENU" anytime to exit the menu and return to the Acer
welcome screen.
19
Empowering
Key
Acer Empowering Key provides three
Acer unique functions: "Acer eView
Management", "Acer eTimer
Management", "Acer eOpening
Management" and "Acer ePower
Management". Press " " for more
than one second to launch the
Onscreen Display main menu to modify
its function.
Acer eView Management
(S5201/T111/PS-X11/
S5201B/T111E/PS-X11K/
S5301WB/T121E/PSW11K)
(P5206/N216/PN-X14)
Acer eTimer Management
Press " " to launch "Acer eView
Management".
"Acer eView Management" is for
display mode selection. Please refer to
the "Onscreen Display (OSD) Menus"
section for more details.
The 3D and 3D Sync Invert functions
offer quick access of 3D functions here.
Press " " to launch "Acer eTimer
Management".
"Acer eTimer Management" provides
the reminding function for
presentation time control. Please refer
to the "Onscreen Display (OSD) Menus"
section for more details.
Acer eOpening Management Press " " to launch "Acer eOpening
Management".
"Acer eOpening Management" allows
users to change the Startup Screen to
their personalized image. Please refer
to the "Onscreen Display (OSD) Menus"
section for more details.
Acer ePower Management
Press " " to launch "Acer ePower
Management".
"Acer ePower Management"provides
you one shortcut to save the lamp and
projector’s life. Please refer to the
"Onscreen Display (OSD) Menus"
section for more details.
English
Acer Empowering Technology
English
20
Onscreen Display (OSD) Menus
The projector has multilingual Onscreen Display (OSD) menus that allow
you to make image adjustments and change a variety of settings.
Using the OSD menus
•
To open the OSD menu, press "MENU" on the control panel or remote
control.
•
When the OSD is displayed, use
to select an item in the main menu.
After selecting the desired main menu item, press
for feature setting.
•
Use
to enter a submenu
to select the desired item and adjust the settings by using
.
•
Select the next item to be adjusted in the submenu and adjust as described
above.
•
Press "MENU" on the control panel or remote control, the screen will
return to the main menu.
•
To exit the OSD menu, press "MENU" on the control panel or remote
control again. It will close and the projector will automatically save the
new settings.
Main menu
Setting
Submenu
21
English
Color
There are many factory presets optimized for various types
of images.
Display Mode
Wall Color
•
Bright: For brightness optimization.
•
Presentation: For meeting presentation with higher
brightness.
•
Standard: For common environment.
•
Video: For playing video in a bright environment.
•
Education: For education environment. (for S5201/
T111/PS-X11/S5201B/T111E/PS-X11K/S5301WB/T121E/
PS-W11K)
•
User: Memorize user’s settings.
Use this function to choose a proper color according to the
wall. There are several choices, including white, light
yellow, light blue, pink, dark green. It will compensate the
color deviation due to the wall color to show the correct
image tone.
Adjusts the brightness of the image.
Brightness
Contrast
Color
Temperature
•
Press
to darken the image.
•
Press
to lighten the image.
Controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast
changes the amount of black and white in the image.
•
Press
to decrease the contrast.
•
Press
to increase the contrast.
Adjusts the color temperature. At higher color
temperatures, the screen looks colder; at lower color
temperatures, the screen looks warmer.
English
22
Degamma
Effects the representation of dark scenery. With greater
gamma value, dark scenery will look brighter.
Color R
Adjusts the red color.
Color G
Adjusts the green color.
Color B
Adjusts the blue color.
Adjusts a video image from black and white to fully
saturated colors.
Saturation
•
Press
image.
to decrease the amount of color in the
•
Press
image.
to increase the amount of color in the
Adjusts the color balance of red and green.
Tint
•
Press
image.
to increase the amount of green in the
•
Press
to increase the amount of red in the image.
Adjusts the color range of the HDMI image data to prevent
color display error.
HDMI Color
Range
•
Auto: Automatically adjusts the color range by
information from the player.
•
Limited Range: Processes the input image as limited
color range data.
•
Full Range: Processes the input image as full color
range data.
Note: "Saturation" and "Tint" functions are not supported under
computer, or HDMI (PC) mode.
Note: "HDMI Color Range" is only available when the input signal is HDMI.
23
Projection
English
Image
•
Front-Desktop: The factory default setting.
•
Front-Ceiling: When you select this function, the
projector inverts the image for ceiling-mounted
projection.
•
Rear-Desktop: When you select this function, the
projector reverses the image so that you can project
behind a translucent screen.
•
Rear-Ceiling: When you select this function, the
projector reverses and inverts the image at same time.
You can project from behind a translucent screen with
ceiling mounted projection.
Use this function to choose your desired aspect ratio.
Aspect Ratio
Keystone
•
Auto: Keeps the image with original width-height ratio
and maximizes the image to fit native horizontal or
vertical pixels.
•
4:3: The image will be scaled to fit the screen and
displayed using a 4:3 ratio.
•
16:9: The image will be scaled to fit the screen and
displayed using a 16:9 ratio.
•
Full (for S5301WB/T121E/PS-W11K): The image will be
displayed making full use of the horizontal and vertical
pixels.
•
L.Box (for S5301WB/T121E/PS-W11K): Keeps the original
signal aspect ratio and zooms in by 1.333 times.
Manually adjusts image distortion caused by tilting projection
(±40 degrees).
English
24
Adjusts the sharpness of the image.
•
Press
to decrease the sharpness.
•
Press
to increase the sharpness.
H. Position
(Horizontal
Position)
•
Press
to move the image left.
•
Press
to move the image right.
V. Position
(Vertical
Position)
•
Press
to move the image down.
•
Press
to move the image up.
Sharpness
Frequency
Changes the projector’s refresh rate to match the frequency
of your computer’s graphics card. If you experience a vertical
flickering bar in the projected image, use this function to
correct it.
Tracking
Synchronizes the signal timing of the display with the graphics
card. If you experience an unstable or flickering image, use
this function to correct it.
Adjusts the overscan ratio of the HDMI image on screen.
•
Auto: Automatically adjusts the overscan ratio by
information from the player.
•
Underscan: Always no overscan on the HDMI image.
•
Overscan: Always keep overscan on the HDMI image.
HDMI Scan Info
Choose "On" to enable DLP 3D function.
•
3D
DLP 3D
Select this item while using DLP 3D glasses, quad buffer
(NVIDIA/ATI...) graphics card and HQFS format file or DVD
with corresponding SW player.
•
Off
Turns off 3D mode.
3D Sync Invert
If you see a discrete or overlapping image while wearing DLP
3D glasses, you may need to execute "Invert" to get best
match of left/right image sequence to get the correct image
(for DLP 3D).
Choose "On" to display the 3D warning message.
3D Warning
Message
25
Note: "Sharpness" function is not supported under computer mode.
Note:
The 3D function is supported by VGA source only. Please see the timing
table for detailed 3D timings.
It needs correct settings on graphics card 3D application program for correct
3D display.
The SW players, such as Stereoscopic Player and DDD TriDef Media Player
can support 3D format files. You can download these players on web page
below.
-NVIDIA Stereoscopic 3D Video Player: http://www.nvidia.com/object/
3D_Drivers_Downloads.html
-Stereoscopic Player: http://www.3dtv.at/Downloads/Index_en.aspx
-DDD TriDef Media Player: http://www.tridef.com/download/TriDef-3-DExperience-4.0.2.html
Note: "3D Sync Invert" is only available when DLP 3D is enabled.
Setting
(P5206/N216/PN-X14/S5201/
T111/PS-X11)
Menu Location
(S5201B/T111E/PS-X11K/
S5301WB/T121E/PS-W11K)
Chooses the OSD menu location on the display screen.
English
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under video mode.
English
26
Startup Screen
Use this function to select your desired startup screen. If you
change the setting, it will take effect when you exit the OSD
menu.
•
Acer: The default startup screen of your Acer projector.
•
User: Use the memorized picture from the "Screen
Capture" function.
Use this function to customize the startup screen. To capture
the image that you want to use as the startup screen, follow
the instructions below.
Notice:
Before proceeding with the following steps, make sure that
the "Keystone" is set to the default value "0", and the
"Aspect Ratio" is set to "4:3". For details, refer to the "Image"
section.
Screen Capture
•
Change the "Startup Screen" from the default setting
"Acer" to "User".
•
Press "Screen Capture" to customize the startup screen.
•
A dialog box appears to confirm the action. Choose
"Yes" to use the current image as your customized
startup screen. Choose "No" to cancel the screen capture
and exist the onscreen display (OSD).
•
A message appears stating that the screen capture is in
progress.
•
When the screen capture is finished, the message
disappears and the original display is shown.
•
The customized startup screen takes effect when there is
a new input signal or when you restart the projector.
Note: This screen capture function is limited by 4:3
aspect ratio only.
Note: For XGA models, to get best quality for your
desired image, it is suggested that you set the PC
resolution to 1024 x 768 before using this function.
Note: For SVGA models, to get best quality for your
desired image, it is suggested that you set the PC
resolution to 800 x 600 before using this function.
Note: For WXGA models, to get best quality for your
desired image, it is suggested that you set the PC
resolution to 1280 x 800 before using this function.
27
Set your screen aspect ratio to 4:3. The function is not
available when the aspect ratio is "16:9" or 16:9 format
detected under "Auto mode".
Security
This projector provides a useful security function for the
administrator to manage the projector.
Press
Security
to change the "Security" setting. If the security
function is enabled, your must enter "Administrator
Password" first before changing the security setting.
The factory default of "Administrator Password" is
"1234".
•
Select "On" to enable the security function. You have to
enter password depending on the "Security Mode".
Please refer to "User Password" section for details.
•
If "Off" is selected, you can switch on the projector
without password.
Timeout (Min.)
Once "Security" is set to "On", you can set timeout function.
•
Press
•
The range is from 10 to 990 minutes.
•
When time is up, the projector will request you to enter
the password again.
•
The factory default setting of "Timeout (Min.)" is "Off".
•
Once the security function is enabled, the projector will
request you to enter password when switching on the
projector. Both "User Password" and "Administrator
Password" can be accepted for this dialogue.
to select timeout duration.
English
Closed Caption
Selects a preferred closed captioning mode from CC1, CC2,
CC3, CC4, (CC1 displays captions in the primary language in
your area). Select "Off" to turn off the captioning feature.
This function is only available when a composite video or SVideo input signal is selected and its system format is NTSC.
28
English
User Password
•
Press
•
Use the numerical keys on the remote control to set the
password and press "MENU" to confirm.
•
To delete the digits, Press
•
Enter the password again when you see "Confirm
Password" displayed.
•
The password should be 4~8 digits in length.
•
If you select "Request password only after plugging
power cord", you are requested to input the password
every time the power cord is plugged.
•
If you select "Always request password while projector
turns on", you are requested to input the password every
time the projector is turned on.
to set up or change "User Password".
.
Administrator Password
You can enter "Administrator Password" when the "Enter
Administrator Password" or "Enter Password" dialogue box is
displayed.
•
Press
to change "Administrator Password".
•
The factory default of "Administrator Password" is
"1234".
If you forget your administrator password, do the following
to retrieve the administrator password:
•
Enter the unique 6-digit "Universal Password" which is
printed on the Security Card that came with your
projector. This unique password will be accepted by the
projector no matter what the administrator password is.
•
If the Security Card is lost, please contact your local Acer
service center.
Lock User Startup Screen
•
VGA OUT
The default value is "Off". If it is "On", you cannot
change the startup screen arbitrarily.
Selecting "On" enables the function. The projector can output
a VGA signal when it is in standby mode and the VGA IN (or
VGA IN 1) and VGA OUT sockets are correctly connected to the
devices.
Enabling this function slightly increases the standby
power consumption.
29
Press
after choosing "Yes" to return the display
English
Reset
parameters on all menus to the factory default settings.
To connect your projector to the network:
1
Take a RJ45 cable and connect one end to the LAN input
jack of the projector and the other end to the RJ45 port.
2
Enter the LAN Setting menu. The "Enter Administrator
Password" dialogue box is displayed.
3
Enter "Administrator Password". The next level menu
is displayed.
The factory default of "Administrator Password" is
"1234". You can change it in the Setting > Security >
Administrator Password menu.
LAN Setting
(for P5206/
N216/PN-X14/
S5201/T111/PSX11)
4
Select LAN in this menu and press
5
Make sure DHCP is on, and press
press
.
to select "On".
6
Re-enter the menu and note down the IP address
displayed in the row of Projector IP Address.
to select Apply and
If your are not in a DHCP environment, set DHCP to "Off" and
contact your ITS administrator for information on Projector IP
Address, Subnet Mask, Default Gateway, and DNS Server.
1
Press
to select Projector IP Address and press
2
Press
to move the cursor and press
enter the digits.
3
When you finish, press MENU to save and exit the menu.
4
Repeat steps 1-3 to input addresses for Subnet Mask,
Default Gateway, DNS server.
5
Press
to highlight Apply and press
.
to
.
To control the projector remotely:
LAN Reset
(for P5206/
N216/PN-X14/
S5201/T111/PSX11)
1
Enter the Projector IP address in the address bar of the
web browser on your computer.
2
The remote network operation page is displayed.You can
control the projector by using this page. For details, see
the notes following this table.
Press
after choosing "Yes" to return all items on the Tools
page to the default settings.
English
30
LAN
•
(for S5201B/
T111E/PS-X11K/
S5301WB/
T121E/PS-W11K)
The default value is "Off". Choose "On" to enable the
LAN connection.
LAN IP/Mask
•
(for S5201B/
T111E/PS-X11K/
S5301WB/
T121E/PS-W11K)
Identify IP and Mask address.
LAN Reset
•
(for S5201B/
T111E/PS-X11K/
S5301WB/
T121E/PS-W11K)
Reset LAN function.
Auto Screen
The default value is "On". The up/down move of your
electronic screen relates to power on/off of the projector.
About LAN Setting (for P5206/N216/PN-X14/S5201/T111/PS-X11)
Note 1 : An overview of the remote network operation page
See Note 2 and
Note 3.
To switch
input signals,
click your
desired
signal.
These buttons
function the
same as those
on the OSD
menus,
projector
control panel,
or remote
control.
31
You can
enter the
projector
information.
You can
adjust the
LAN control
settings.
You can set the
user password/
administrator
password to
prevent
unauthorized use
of the remote
network operation/
Tools page.
Note 3: The Info page shows the projector information and status.
Management
ECO Mode
Choose "On" to dim the projector lamp, which will also
lower the power consumption, reduce noise, and extend
the lamp life. Choose "Off" to return to the normal mode.
English
Note 2 : An overview of the Tools page
English
32
High Altitude
Choose "On" to turn on the High Altitude mode. When
this function is turned on, the projector fans operate at full
speed continuously to cool down the projector’s
temperature.
Auto Shutdown
(Minutes)
The projector will automatically shut down while there is
no signal input detected after the setting time.
Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding
Lamp Hour Reset
Choose this function to show or hide warning message
when the changing lamp message is displayed. The
message will show up 30 hours before end of life.
Press
after choosing "Yes" to turn the lamp hour
counter to 0 hours.
Audio
Volume
Microphone
Volume
Mute
Power On/Off
Volume
Alarm Volume
•
Press
to decrease the projector speaker volume.
•
Press
to increase the projector speaker volume.
•
Press
to decrease the microphone volume.
•
Press
to increase the microphone volume.
•
Choose "On" to turn mute on.
•
•
Choose "Off" to turn mute off.
•
Select this function to adjust the volume of any
warning notifications.
Select this function to adjust the notification
volume when turning the projector on/off.
33
English
Timer
Timer Location
Sets the location of the timer on the screen.
Timer Start (or
Stop)
Press
Timer Period
(Minutes)
Press
Timer Volume
Select this function to adjust the notification volume
when the timer function is enabled and time is up.
Timer Display
Press
to start or stop the timer.
to adjust the timer period.
to choose a timer display mode.
Language
Language
Sets a language for the OSD menus. Use
select your preferred language.
•
Press
to confirm the selection.
to
English
34
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
#
1
2
Problem
No image appears
onscreen
Partial, scrolling
or incorrectly
displayed image
(For PC (Windows
95/98/2000/XP))
Solution
•
Make sure all the cables are correctly connected as
described in the "Getting Started" section.
•
Ensure none of the connector pins are bent or
broken.
•
Check if the projection lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
•
Make sure you have removed the lens cap and the
projector is switched on.
•
Press "RESYNC" on the control panel or remote
control.
•
For an incorrectly displayed image:
•
Open "My Computer > Control Panel," and
then double-click the "Display" icon.
•
Select the "Settings" tab.
•
Verify that your display resolution setting is
lower than or equal to UXGA (1600 x 1200).
•
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
•
Verify that the resolution setting is lower than
or equal to UXGA (1600 x 1200).
•
Click the "Change" button under the
"Monitor" tab.
•
Click "Show all devices > Standard monitor
types" under the SP box, and choose the
resolution mode you need under the "Models"
box.
•
Verify that the resolution setting of the
monitor display is lower than or equal to UXGA
(1600 x 1200).
35
4
5
6
7
Partial, scrolling
or incorrectly
displayed image
(For notebooks)
The screen of the
notebook
computer is not
displaying your
presentation
Image is unstable
or flickering
Image has vertical
flickering bar
Image is out of
focus
•
Press "RESYNC" on the control panel or remote
control.
•
For an incorrectly displayed image:
•
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
•
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]
•
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
•
If you are using a Microsoft® Windows® based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
•
If you are using an Apple® Mac® OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On."
•
Use "Tracking" to correct it. Refer to the "Image"
section for more information.
•
Change the display color setting on your computer.
•
Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
•
Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
•
•
•
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the
required distance of 3.9 to 30.2 feet (1.2 to 9.2
meters) from the P5206/N216/PN-X14 projector, 1.6
to 12.2 feet (0.5 to 3.7 meters) from the S5201/T111/
PS-X11/S5201B/T111E/PS-X11K, or 1.6 to 10.4 feet
(0.5 to 3.2 meters) from the S5301WB/T121E/PSW11K projector. Refer to the "How to Get a
Preferred Image Size by Adjusting Distance and
Zoom" section for more information.
English
3
English
36
8
9
10
11
Image is stretched
when displaying a
"widescreen"
DVD title
Image is too small
or too large
Image has slanted
sides
Image is reversed
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
•
If you play a 4:3 format DVD title, please change the
format to 4:3 with the projector OSD.
•
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
•
•
Adjust the zoom lever on the top of the projector.
•
Press "MENU" on the control panel or remote
control. Go to "Image > Aspect Ratio" and try
different settings.
•
If possible, reposition the projector so that it is
centered on the screen and below the bottom of the
screen.
•
Press the Keystone correction keys on the control
panel or remote control until the image becomes
square.
•
Press "MENU" on the control panel or remote
control to open the OSD menu. Go to "Image > Auto
Keystone" or "Image > Manual Keystone" to make
adjustments.
•
Select "Image > Projection" on the OSD and adjust
the projection direction.
Move the projector closer to or further from the
screen.
Problems with the Projector
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2
Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
37
#
1
Condition
Message
Message Reminder
Fan Fail - the system fan is not working.
Fan Fail.
Lamp will automatically turn off soon.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it is used. Please also check the dust filters if
they are installed. If the dust filter is clogged with dust, please
clean it.
Projector Overheated.
Lamp will automatically turn off soon.
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!
English
OSD Messages
English
38
LED & Alarm Definition Listing
LED Messages
Message
Power LED
Lamp LED
Temp LED
Red
Blue
Red
Red
Standby
(Power cord plugged in)
V
--
--
--
Power on
--
V
--
--
Lamp retry
--
Quick
flashing
--
--
Turning off (Cooling
state)
Quick
flashing
--
--
--
Turning off (Cooling
completed)
V
--
--
--
Error (Thermal failure)
--
V
--
V
Error (Fan lock failure)
--
V
--
Quick
flashing
Error (Lamp breakdown)
--
V
V
--
Error (Color wheel
failure)
--
V
Quick
flashing
--
39
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life itself. It will show you a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement Suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooled down for at least 30
minutes before changing the lamp.
Warning: Lamp compartment is hot! Allow it to cool down before
changing lamp!
9
3
2
10
4
1
1
2
1
2
8
12
5
8
6
7
11
1
12
To remove the lamp:
1
Turn the projector off by pressing
2
Allow the projector at least 30 mins to cool down.
(POWER).
3
Disconnect the power cord.
4
Use a screwdriver to remove the screws from the cover. (Illustration #1)
5
Push up and remove the cover.
6
Remove and dispose of the lamp protection film (Illustration #2).
7
Remove the screw that secures the lamp module (Illustration #3).
8
Pull out the lamp connector from a slot in the lamp compartment.
Disconnect it from the projector (Illustration #4).
9
Lift the handle so that it stands up (Illustration #5). Pull out the lamp
module by force (Illustration #6).
To replace the lamp module, use a new lamp and follow illustrations #
7
- #112 .
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
English
Replacing the Lamp
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
m
m
m
13 m
20
1
.9
49mm
130 mm
mm
8.4
English
40
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
2
Secure the ceiling rod using the appropriate type of cylinder screws.
Ceiling Mount
Base
- Attach to
ceiling
Short Rod
Long Rod
Extension Rod
Screw Type A
50 mm length / 8 mm diameter -
Large Cylinder Cap
Allen Key
- For tighten/loosen
Tightening Screw
Medium Rod
41
Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Screw Type B
Screw Type C
Sliding Extension
Large Washer
Projector Bracket
Supports projector and
allows for adjustments
Smaller Washer
Spacer
- For heat dissipation
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4
Attach the ceiling bracket to the ceiling rod.
Tightening Screw
Screw Type A
50 mm length /8 mm diameter
Large Cylinder Cap
Allen Key
- For tighten/loosen
English
3
5
Adjust the angle and positioning as necessary.
Tightening Screw
Allen Key
30
Allen Key
Tightening Screw
Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models
Screw Type B
P5206/N216/PN-X14/
S5201/T111/PS-X11/S5201B/
T111E/PS-X11K/S5301WB/
T121E/PS-W11K
Washer Type
Diameter (mm)
Length (mm)
Large
Small
3
25
V
V
149.5 mm
English
42
Screw M3
Depth 9.5 mm
242.04 mm
43
The specifications below are subject to change without notice. For final specs,
please refer to Acer's marketing documentation.
Projection system
DLP™
Resolution
•
P5206/N216/PN-X14/S5201/T111/PS-X11/S5201B/T111E/
PS-X11K:
Native: XGA (1024 x 768)
Maximum: 1920 x 1080 EIA/RB
•
S5301WB/T121E/PS-W11K:
Native: WXGA (1280 x 800)
Maximum: 1920 x 1080 EIA/RB
Computer compatibility
IBM PC and compatibles, Apple Macintosh, iMac and VESA
standards: WXGA+ (1440 x 900), WXGA (1280 x 800, 1280 x
768), SXGA (1152 x 864, 1280 x 1024), SXGA+ (1400 x 1050),
XGA (1024 x 768), SVGA (800 x 600), VGA (640 x 480), UXGA
(1600 x 1200), 1920 x 1080 EIA/RB
Video compatibility
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/K/K1/L),
HDTV (720p, 1080i, 1080p), EDTV (480p, 576p), SDTV (480i,
576i)
Aspect ratio
•
P5206/N216/PN-X14/S5201/T111/PS-X11/S5201B/T111E/
PS-X11K: Auto, 4:3 (native), 16:9
•
S5301WB/T121E/PS-W11K: Auto, Full (native), 16:9, 4:3,
L.Box
Displayable colors
1.07 billion colors
Projection lens
•
P5206/N216/PN-X14:
F = 2.59 - 2.87, f = 16.88 mm - 21.88 mm,
1:1.3 Manual Zoom and Manual Focus
•
S5201/T111/PS-X11/S5201B/T111E/PS-X11K:
F = 2.6, f = 6.90 mm, Manual Focus
•
S5301WB/T121E/PS-W11K:
F = 2.6, f = 6.90 mm, Manual Focus
Projection screen size
(diagonal)
Projection distance
Throw ratio
•
•
P5206/N216/PN-X14: 30" (76 cm) - 300" (762 cm)
•
S5301WB/T121E/PS-W11K: 47" (120 cm) - 300" (762 cm)
•
•
P5206/N216/PN-X14: 3.9' (1.2 m) - 30.2' (9.2 m)
•
S5301WB/T121E/PS-W11K:1.6' (0.5 m) - 10.4' (3.2 m)
•
•
P5206/N216/PN-X14: 65" @ 2 m (1.51 - 1.97 : 1)
•
S5301WB/T121E/PS-W11K: 87" @ 92 cm (0.49 : 1)
S5201/T111/PS-X11/S5201B/T111E/PS-X11K: 40" (102 cm)
- 300" (762 cm)
S5201/T111/PS-X11/S5201B/T111E/PS-X11K: 1.6' (0.5 m) 12.2' (3.7 m)
S5201/T111/PS-X11/S5201B/T111E/PS-X11K: 77" @ 95 cm
(0.61 : 1)
Horizontal scan rate
31 - 100 kHz
Vertical refresh scan rate
48 - 120 Hz
English
Specifications
English
44
Lamp type
•
•
P5206/N216/PN-X14: Philips 300 W user-replaceable UHP
S5201/T111/PS-X11/S5201B/T111E/PS-X11K/S5301WB/
T121E/PS-W11K: Philips 230 W user-replaceable VIP
Keystone correction
+/-40 Degrees (Vertical), Manual
Digital zoom
2X
Audio
5Wx2
Weight
•
•
P5206/N216/PN-X14: Approximate 3.25 kg (7.12 lbs.)
•
P5206/N216/PN-X14: 290 x 255 x 125 mm (11.4" x 10.0"
x 4.9")
•
S5201/T111/PS-X11/S5201B/T111E/PS-X11K/S5301WB/
T121E/PS-W11K: 290 x 254 x 98.5 mm (11.4" x 10.0" x
3.9")
Dimensions (W x D x H)
S5201/T111/PS-X11/S5201B/T111E/PS-X11K/S5301WB/
T121E/PS-W11K: Approximate 3.5 kg (7.72 lbs.)
Power supply
Universal AC input 100 - 240 V, input frequency 50/60 Hz
Power consumption
•
•
P5206/N216/PN-X14: 447 W
S5201/T111/PS-X11/S5201B/T111E/PS-X11K/S5301WB/
T121E/PS-W11K: 352 W
Operating temperature
0ºC to 35ºC / 32ºF to 95ºF
I/O connectors
•
Power socket x 1
•
RS232 x 1
•
VGA input x 2
•
VGA output x 1
•
Composite video x 1
•
S-Video x 1
•
3.5 mm audio jack input x 2
•
3.5 mm audio jack output x 1
•
HDMI x 2
•
RJ45 LAN input x 1
•
USB (Type mini B) x 1
•
12 V DC output x 1 (Max. 1A)
•
Microphone input x 1
Below items are for S5201B/T111E/PS-X11K/S5301WB/
T121E/PS-W11K only.
•
USB (Type A) x 2
45
AC power cord x 1
•
VGA cable x 1
•
Remote control x 1
•
Battery x 2 (for the remote control)
•
User's guide (CD-ROM) x 1
•
Quick start guide x 1
•
Security card x 1
•
Composite video cable x 1
•
Carrying case x 1
Below items are for S5201B/T111E/PS-X11K/S5301WB/
T121E/PS-W11K only.
Accessory (optional)
•
•
Acer Projector Gateway (CD-ROM) x 1
•
Dust filter x 1
Acer Projector Gateway quick start guide x 1
*Design and specifications are subject to change without notice.
English
Standard package contents •
English
46
Compatibility Modes
1
VGA Analog - PC Signal
Mode
Resolution
V.Frequency [Hz]
VGA_60
640 x 480
59.940
31.469
VGA_72
72.809
37.861
VGA_75
75.000
37.500
VGA_85
85.008
43.269
VGA_70
720 x 400
H.Frequency [KHz]
70.087
31.469
85.039
37.927
56.250
35.156
SVGA_60
60.317
37.879
SVGA_72
72.188
48.077
SVGA_75
75.000
46.875
SVGA_85
85.061
53.674
VGA_85
SVGA_56
XGA_60
800 x 600
60.004
48.363
XGA_70
1024 x 768
70.069
56.476
XGA_75
75.029
60.023
XGA_85
84.997
68.677
70.012
63.851
SXGA_75
75.000
67.500
SXGA_85
84.990
77.094
60.020
63.981
SXGA_72
72.000
76.970
SXGA_75
75.025
79.976
SXGA_70
SXGA_60
1152 x 864
1280 x 1024
SXGA_85
QuadVGA_60
1280 x 960
QuadVGA_75
85.024
91.146
60.000
60.000
75.000
75.000
SXGA+_60
1400 x 1050
59.978
65.317
UXGA_60
1600 x 1200
60.000
75.000
Mac G4
640 x 480@60Hz
59.940
31.469
MAC13
640 x 480@67Hz
66.667
35.000
Mac G4
800 x 600@60Hz
60.317
37.879
MAC16
832 x 624@75Hz
74.546
49.722
Mac G4
1024 x 768@60Hz
60.004
48.363
47
1024 x 768@75Hz
75.020
60.241
MAC21
WXGA_60
1152 x 870@75Hz
75.061
68.681
1280 x 768
59.870
47.776
WXGA_75
74.893
60.289
WXGA_85
84.837
68.633
60.000
45.000
WXGA_60
1280 x 720
WXGA_60
1280 x 800
WXGA_120*
•
2
59.810
49.702
119.909
101.563
55.935
WXGA+_60
1440 x 900
59.887
1680 x 1050_60
1680 x 1050
59.954
65.290
1920 x 1080_RB
1920 x1080
60.000
66.587
1920 x 1080_EIA
1920 x1080
60.000
67.500
acer_16:9
1366 x 768
59.790
47.712
acer_timing
1024 x 600
60.000
37.500
VGA_120
640 x 480
119.518
61.910
SVGA_120
800 x 600
119.854
77.425
XGA_120
1024 x 768
119.804
98.958
* (star sign): For S5301WB/T121E/PS-W11K only
DVI-D & HDMI (HDCP) Timing
Mode
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
VGA_60
640 x 480
59.940
31.469
VGA_72
72.809
37.861
VGA_75
75.000
37.500
VGA_85
VGA_70
720 x 400
VGA_85
SVGA_56
800 x 600
85.008
43.269
70.087
31.469
85.039
37.927
56.250
35.156
SVGA_60
60.317
37.879
SVGA_72
72.188
48.077
SVGA_75
75.000
46.875
SVGA_85
85.061
53.674
60.004
48.363
XGA_70
70.069
56.476
XGA_75
75.029
60.023
XGA_85
84.997
68.677
XGA_60
1024 x 768
English
MAC19
English
48
SXGA_70
1152 x 864
70.012
63.851
75.000
67.500
SXGA_85
1152 x 864
84.990
77.094
SXGA_60
1280 x 1024
SXGA_75
60.020
63.981
SXGA_72
72.000
76.970
SXGA_75
75.025
79.976
SXGA_85
85.024
91.146
1280 x 960
60.000
60.000
75.000
75.000
SXGA+_60
1400 x 1050
59.978
65.317
UXGA_60
1600 x 1200
60.000
75.000
QuadVGA_60
QuadVGA_75
Mac G4
640 x 480@60Hz
59.940
31.469
MAC13
640 x 480@67Hz
66.667
35.000
37.879
Mac G4
800 x 600@60Hz
60.317
MAC16
832 x 624@75Hz
74.546
49.722
Mac G4
1024 x 768@60Hz
60.004
48.363
MAC19
1024 x 768@75Hz
75.020
60.241
MAC21
1152 x 870@75Hz
75.061
68.681
WXGA_60
1280 x 768
59.870
47.776
74.893
60.289
WXGA_75
WXGA_85
84.837
68.633
WXGA_60
1280 x 720
60.000
45.000
WXGA_60
1280 x 800
59.810
49.702
WXGA_120*
119.909
101.563
WXGA+_60
1440 x 900
59.887
55.935
65.290
1680x1050_60
1680 x 1050
59.954
1920x1080_RB
1920 x1080
60.000
66.587
1920x1080_EIA
1920 x1080
60.000
67.500
acer_16:9
1366 x 768
59.790
47.712
acer_timing
VGA_120
1024 x 600
640 x 480
60.000
119.518
37.500
61.910
SVGA_120
800 x 600
119.854
77.425
XGA_120
1024 x 768
119.804
98.958
480p
Video (HDMI)
60
31.47
576p
50
31.25
720p_60
60
45.00
49
3
4
50
37.50
1080i_60
60
33.75
1080i_50
50
28.13
1080p
60
67.5
1080P
1080p
50
24
56.26
27.00
1080p
23.98
26.97
* (star sign): For S5301WB/T121E/PS-W11K only
Component Signal
Mode
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
480i
720 x 480
59.94
15.73
480p
720 x 480
59.94
31.47
576i
720 x 576
50.00
15.63
576p
720 x 576
50.00
31.25
720p
1280 x 720
60.00
45.00
720p
1280 x 720
50.00
37.50
1080i
1920 x 1080
60.00
33.75
1080i
1920 x 1080
50.00
28.13
1080p
1920 x 1080
60.00
67.5
1080p
1920 x 1080
50.00
56.26
1080p
1920 x 1080
24.00
27.00
1080p
1920 x 1080
23.98
26.97
Video, S-Video Signal
Video mode
V.Frequency [Hz] H.Frequency [KHz]
fsc (MHz)
NTSC
60
15.73
3.58
PAL
50
15.63
4.43
SECAM
50
15.63
4.25 or 4.41
PAL-M
60
15.73
3.58
PAL-N
50
15.63
3.58
PAL-60
60
15.73
4.43
NTSC4.43
60
15.73
4.43
English
•
720p_50
English
50
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the device and receiver.
•
Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby, declares that this projector series is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a
Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b
Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
English
Remarque à l'intention des utilisateurs canadiens
English
51
English
52
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact a local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai, e-mail:easy_lai@acer.com.tw
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921, Fax: +39-02 9399-2913, www.acer.it
Hereby declare that:
Product:
Trade Name:
Model Number:
Projector
Acer
QNX1017/QNX1020/QNX1021/QWX1026/N216/PN-X14/T111/
PS-X11/T111E/PS-X11K/T121E/PS-W11K series
Machine Type:
P5206/S5201/S5201B/S5301WB series
Is compliant with the essential requirements and other relevant provisions of the following EC
directives, and that all the necessary steps have been taken and are in force to assure that production
units of the same product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following harmonized standards:
-. EN55022, AS/NZS CISPR22, Class B
-. EN55024
-. EN61000-3-2 Class A
-. EN61000-3-3
Low Voltage Directive 2006/95/EC as attested by conformity with the following harmonized
standard:
-. EN60950-1
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous Substances in
Electrical and Electronic Equipment
-. The maximum concentration values of the restricted substances by weight in homogenous
material are:
0.1%
Polybrominated Biphenyls (PBB’s)
Mercury
Lead
0.1%
Polybrominated Diphenyl Ethers (PBDE’s)
0.1%
0.1%
Hexavalent Chromium
0.1%
Cadmium
0.01%
Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
English
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih
Taipei Hsien 221, Taiwan
English
53
English
54
Acer Incorporated
8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih
Taipei Hsien 221, Taiwan
The standards listed below are applied to the product if built with WLAN module or wireless
keyboard and mouse.
R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard:
•
Article 3.1(a) Health and Safety
-. EN60950-1
-. EN62311
•
Article 3.1(b) EMC
-. EN301 489-1
-. EN301 489-17
•
Article 3.2 Spectrum Usages
-. EN300 328
-. EN301 893 (Applicable to 5GHz high performance RLAN).
Year to begin affixing CE marking 2010.
Easy Lai /Manager
Regulation Center, Acer Inc.
Dec. 1, 2010 Date
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product:
DLP Projector
Model Number:
QNX1017/QNX1020/QNX1021/
QWX1026/N216/PN-X14/T111/
PS-X11/T111E/PS-X11K/T121E/
PS-W11K
Machine Type:
P5206/S5201/S5201B/S5301WB series
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147
English
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147
English
55
Download PDF