Slip-On (2012)

Slip-On (2012)
Installation Instructions
4.
Attach slip-on tube to TBR muffler using the provided 4
6x20mm bolts and lock washers with X-ring. Leave loose
for now.
5.
Attach muffler mounting bracket (supplied) to rear OEM
muffler mounting hole using the supplied 8x60mm bolt
and nut as shown.
6.
Loosely install muffler assembly and attach to mounting
bracket using the OEM bolt and nut for alignment. After
exhaust is aligned tighten one X-ring bolt to secure sliptube in place.
7.
Remove muffler assembly and tighten the remaining
X-ring bolts and re-install and secure in place using OEM
nut and bolt.
IMPORTANT - PLEASE READ CAREFULLY
8.
Tighten Barrel clamp.
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Be sure
to save all stock components for possible use later.
9.
Double check your work and make sure all bolts are
tightened and the exhaust is aligned correctly.
1.
Make sure the ATV is completely cool before starting
the installation. Make sure the ATV is secure on a level
surface and the parking brake is set.
2.
Remove muffler.
V.A.L.E.
TM
2012 Can-am
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
Outlander 1000R
V.A.L.E.™ Slip-on Exhaust System with M-7 Aluminum Canister
Part # 005-3130406V
3.
**This product has not been tested with all available accessories and some
items may cause excessive heat. Excessive heat may cause damage to your
vehicle. Two Brothers Racing will not be responsible for damaged parts.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
Remove grommet and sleeve from OEM muffler and
insert into TBR muffler mount.
10. Before you run the ATV, clean off all fingerprints and
dirt, as any oily residue will etch the metal and become
somewhat permanent when the system gets hot. Run the
ATV and enjoy. It is normal for some white smoke to
appear the first time you start the ATV. This is packing/
manufacturing oil from inside the pipe burning off.
Check for gaps or leaks. If you find a leak, a little high
temperature silicon sealant should fix it. After 50 to 100
miles, recheck all fasteners for tightness.
V.A.L.E.
TM
2012 Can-am
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
Outlander 1000R
V.A.L.E.™ Slip-on Exhaust System with M-7 Aluminum Canister
Part # 005-3130406V
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel. Clean
using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Parts List
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep blue/purple through amber after a few heat cycles. This is a normal
characteristic of high quality titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Qty.
Description
Part Number
1
1
1
1
1
1
1
1
1
Muffler Canister M-7 Aluminum
Stainless Steel S-Bend Slip-On HARDWARE KIT
X-Ring Kit
Muffler bracket
8x60mm Socket Head Cap Screw
8mm Flange Nut
61mm Barrel Clamp
TBR Sticker Kit
005-313-206M
005-31304S
005-313-3
005-7-2-3KIT
005-313-B
005-SH860
005-FN8
005-27-61MSH
015-10212
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement