Allied Telesyn International Corp | AT-FS724i | Installation guide | Allied Telesyn International Corp AT-FS724i Installation guide

AT-FS716
AT-FS716E
AT-FS724I
Fast Ethernet Switches
Installation Guide
PN 613-10804-00 Rev. A
Copyright ”1999 Allied Telesyn International, Corp.
960 Stewart Drive Suite B, Sunnyvale CA 94086, USA
All rights reserved. No part of this publication may be reproduced without prior written permission
from Allied Telesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their
respective owners.
Allied Telesyn International, Corp. reserves the right to make changes in specifications and other
information contained in this document without prior written notice. The information provided
herein is subject to change without notice. In no event shall Allied Telesyn International, Corp. be
liable for any incidental, special, indirect, or consequential damages whatsoever, including but not
limited to lost profits, arising out of or related to this manual or the information contained herein,
even if Allied Telesyn International, Corp. has been advised of, known, or should have known, the
possibility of such damages.
Electrical Safety and Installation
Requirements For AT-FS724I
STANDARDS: This product meets the following standards
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and , if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the
FCC, can void your right to operate this equipment.
Canadian Department of Communications
This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
RFI Emission
EN55022 Class A
WARNING: In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Immunity
EN50082-1
Electrical Safety
TUV-EN60950, UL1950, CSA 950
NORMEN: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Hochfrequenzstörung
EN55022 Klasse A
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In
diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen.
Störsicherheit
EN50082-1
Elektrische Sicherheit
TUV-EN60950, UL1950, CSA 950
iii
Electrical Safety and Installation Requirements For AT-FS724I
STANDARDER: Dette produkt tilfredsstiller de følgende standarder.
Radiofrekvens forstyrrelsesemission
EN55022 Klasse A
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det
tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger.
Immunitet
EN50082-1
Elektrisk sikkerhed
TUV-EN60950, UL1950, CSA 950
EISEN: Dit product voldoet aan de volgende eisen.
RFI Emissie
EN55022 Klasse A
WAARSCHUWING:Binnenshuiskanditproductradiostoringveroorzaken,inwelkgevaldegebruiker
verplicht kan worden om gepaste maatregelen te nemen.
Immuniteit
EN50082-1
Electrische Veiligheid
TUV-EN60950, UL1950, CSA 950
NORMES: ce produit est conforme aux normes de suivantes :
Emission d’interférences radioélectriques
EN55022 Classe A
MISEENGARDE:dansunenvironnementdomestique,ceproduitpeutprovoquerdesinterférences
radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates.
Immunité
EN50082 - 1
Sécurité électrique
TUV-EN60950, UL1950, CSA 950
STANDARDIT: Tämä tuote on seuraavien standardien mukainen.
Radioaaltojen häirintä
EN55022 Luokka A
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin.
Kestävyys
EN50082-1
Sähköturvallisuus
TUV-EN60950, UL1950, CSA 950
STANDARD: Questo prodotto è conforme ai seguenti standard.
Emissione RFI (interferenza di radiofrequenza)
EN55022 Classe A
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza.
In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti.
iv
Immunità
EN50082-1
Sicurezza elettrica
TUV-EN60950, UL1950, CSA 950
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
SIKKERHETSNORMER: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
RFI stråling
EN55022 Klasse A
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.
Immunitet
EN50082-1
Elektrisk sikkerhet
TUV-EN60950, UL1950, CSA 950
PADRÕES: Este produto atende aos seguintes padrões.
Emissão de interferência de radiofrequência
EN55022 Classe A
AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção
e, neste caso, pode ser necessário que o utente tome as medidas adequadas.
Imunidade
EN50082-1
Segurança Eléctrica
TUV-EN60950, UL1950, CSA 950
ESTÁNDARES: Este producto cumple con los siguientes estándares.
Emisión RFI
EN55022 Clase A
ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias,
en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al
respecto.
Inmunidad
EN50082-1
Seguridad eléctrica
TUV-EN60950, UL1950, CSA 950
STANDARDER: Denna produkt uppfyller följande standarder.
Radiostörning
EN55022 Klass A
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga
användaren till att vidtaga erforderliga åtgärder.
Immunitet
EN50082-1
Elsäkerhet
TUV-EN60950, UL1950, CSA 950
v
Electrical Safety and Installation Requirements For AT-FS716 and AT-FS716E
Electrical Safety and Installation
Requirements For AT-FS716 and AT-FS716E
STANDARDS: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Manufacture Address:
Allied Telesyn International
950 Kifer Road
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Switches
Model Number:
AT-FS716 and AT-FS716E
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device must not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on. The
user is encouraged to try to correct the interference by one or more of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or registrant of
this equipment can void your authority to operate this equipment under Federal
Communications Commission rules.
vi
Immunity
EN50082-1
Electrical Safety
TUV-EN60950, UL1950, CSA 950
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
NORMEN: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
Hochfrequenzstörung
EN55022 Klasse B
Störsicherheit
EN50082-1
Elektrische Sicherheit
TUV-EN60950, UL1950, CSA 950
STANDARDER: Dette produkt tilfredsstiller de følgende standarder.
Radiofrekvens forstyrrelsesemission
EN55022 Klasse B
Immunitet
EN50082-1
Elektrisk sikkerhed
TUV-EN60950, UL1950, CSA 950
EISEN: Dit product voldoet aan de volgende eisen.
RFI Emissie
EN55022 Klasse B
Immuniteit
EN50082-1
Electrische Veiligheid
TUV-EN60950, UL1950, CSA 950
NORMES: ce produit est conforme aux normes de suivantes :
Emission d’interférences radioélectriques
EN55022 Classe B
Immunité
EN50082 - 1
Sécurité électrique
TUV-EN60950, UL1950, CSA 950
STANDARDIT: Tämä tuote on seuraavien standardien mukainen.
Radioaaltojen häirintä
EN55022 Luokka B
Kestävyys
EN50082-1
Sähköturvallisuus
TUV-EN60950, UL1950, CSA 950
STANDARD: Questo prodotto è conforme ai seguenti standard.
Emissione RFI (interferenza di radiofrequenza)
EN55022 Classe B
Immunità
EN50082-1
Sicurezza elettrica
TUV-EN60950, UL1950, CSA 950
SIKKERHETSNORMER: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
RFI stråling
EN55022 Klasse B
Immunitet
EN50082-1
Elektrisk sikkerhet
TUV-EN60950, UL1950, CSA 950
vii
Electrical Safety and Installation Requirements For AT-FS716 and AT-FS716E
PADRÕES: Este produto atende aos seguintes padrões.
Emissão de interferência de radiofrequência
EN55022 Classe B
Imunidade
EN50082-1
Segurança Eléctrica
TUV-EN60950, UL1950, CSA 950
ESTÁNDARES: Este producto cumple con los siguientes estándares.
Emisión RFI
EN55022 Clase B
Inmunidad
EN50082-1
Seguridad eléctrica
TUV-EN60950, UL1950, CSA 950
STANDARDER: Denna produkt uppfyller följande standarder.
Radiostörning
viii
EN55022 Klass B
Immunitet
EN50082-1
Elsäkerhet
TUV-EN60950, UL1950, CSA 950
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
Safety Information (All Products)
SAFETY
ELECTRICAL NOTICES
WARNING: ELECTRIC SHOCK HAZARD
To prevent ELECTRIC shock , do not remove cover. No user-serviceable parts inside. This
unit contains HAZARDOUS VOLTAGES and should only be opened by a trained and qualified
technician. To avoid the possibility of ELECTRIC SHOCK disconnect electric power to the
product before connecting or disconnecting the LAN cables.
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of LIGHTNING
ACTIVITY.
INSTALLATION
ELECTRICAL—AUTO VOLTAGE ADJUSTMENT
This product will automatically adjust to any voltage between the ranges shown on the
label.
ELECTRICAL—TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a properly wired
earth ground socket outlet. An improperly wired socket outlet could place hazardous
voltages on accessible metal parts.
ELECTRICAL—CORD NOTICE
Use power cord, maximum 4.5 meters long, rated 6 amp minimum, 250V, made of HAR
cordage molded IEC 320 connector on one end and on the other end a plug approved by
the country of end use.
CAUTION: Air vents must not be blocked and must have free access to the room ambient
air for cooling.
OPERATING TEMPERATURE
This product is designed for a maximum ambient temperature of 40 degrees C.
ALL COUNTRIES: Install product in accordance with local and National Electrical Codes.
SICHERHEIT
ACHTUNG: GEFÄHRLICHE SPANNUNG
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile. Das Gerät
steht unter Hochspannung und darf nur von qualifiziertem technischem Personal geöffnet
werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen.
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters ausführen.
INSTALLATION
AUTOMATISCHE SPANNUNGSEINSTELLUNG
Dieses Gerät stellt sich automatisch auf die auf dem Etikett aufgeführten Spannungswerte
ein.
GERÄTE DER KLASSE 1
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger
Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische Spannungen
setzen.
ix
Safety Information (All Products)
NETZKABEL
Das Netzkabel sollte eine maximale Länge von 4,5 Metern, einen Nennwert von mindestens
6 A und 250 V haben, aus HAR-Material hergestellt und mit einer gepreßten, IEC 320
entsprechenden, Anschlußverbindung an einem Ende, und am anderen Ende mit einem im
Land des Endverbrauchers geprüften Stecker ausgestattet sein.
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien
Zugang zur Raumluft haben.
BETRIEBSTEMPERATUR
Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht mehr als
40° C entworfen.
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen Vorschriften
entsprechen.
SIKKERHED
ELEKTRISKE FORHOLDSREGLER
ADVARSEL: RISIKO FOR ELEKTRISK STØD
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele, der kan
repareres af brugeren. Denne enhed indeholder LIVSFARLIGE STRØMSPÆNDINGER og
bør kun åbnes af en uddannet og kvalificeret tekniker. For at undgå risiko for ELEKTRISK
STØD, afbrydes den elektriske strøm til produktet, før LAN-kablerne monteres eller
afmonteres.
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.
INSTALLATION
ELEKTRISK—AUTOMATISK SPÆNDINGSREGULERING
Dette apparat vil automatisk tilpasse sig enhver spænding indenfor de værdier, der er angivet
på etiketten.
ELEKTRISK—KLASSE 1-UDSTYR
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med en korrekt
installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt kan sætte livsfarlig
spænding til tilgængelige metaldele.
ELEKTRISK—EDNING
Anvend ledning af maksimum 4,5 meters længde, med en kapacitet på minimum 6 amp.,
250 v, bestående af en IEC 320 connector med indstøbt HAR ledning i den ene ende og et
stik i den anden ende, der er godkendt af myndighederne i brugerlandet.
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den
omgivende luft i rummet for afkøling.
BETJENINGSTEMPERATUR
Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader C.
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national
lovgivning for elektriske installationer.
x
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
VEILIGHEID
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin
bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen worden. Dit
toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden geopend door een
daartoe opgeleide en bevoegde technicus. Om het gevaar op ELEKTRISCHE SCHOKKEN te
vermijden, moet u het toestel van de stroombron ontkoppelen alvorens de LAN-kabels te
koppelen of ontkoppelen.
GEVAAR VOOR BLIKSEMINSLAG
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.\
INSTALLATIE
ELEKTRISCH - AUTOMATISCHE AANPASSING VAN DE SPANNING
Dit toestel past zich automatisch aan elke spanning aan, tussen de op het label vermelde
waarden.
ELEKTRISCHE TOESTELLEN VAN KLASSE 1
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een juist
geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen onderdelen
waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke spanning stellen.
ELEKTRISCHE SNOEREN
Gebruik een elektrisch snoer, maximum 4,5 meter lang, berekend voor ten minste 6
ampåçère, 250 V, uit HAR vervaardigd, met aan het ene uiteinde een gevormd IEC 320
aansluitstuk en aan het andere uiteinde een stekker die goedgekeurd is door het land waar
het toestel gebruikt zal worden.
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de omgevingslucht
ongehinderd toelaten voor afkoeling.
BEDRIJFSTEMPERATUUR
De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius.
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale elektrische
voorschriften.
SÉCURITÉ
INFORMATION SUR LES RISQUES ÉLECTRIQUES
AVERTISSEMENT: DANGER D’ÉLECTROCUTION
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du matériel. Ce
matériel ne contient aucun élément réparable par l’utilisateur. Il comprend des TENSIONS
DANGEREUSES et ne doit être ouvert que par un technicien dûment qualifié. Pour éviter
tout risque d’ÉLECTROCUTION, débrancher le matériel avant de connecter ou de
déconnecter les câbles LAN.
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.
INSTALLATION
RÉGLAGE DE TENSION AUTOMATIQUE ÉLECTRIQUE
Ce matériel peut s’ajuster automatiquement sur n’importe quelle tension comprise dans la
plage indiquée sur l’étiquette.
xi
Safety Information (All Products)
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE
CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être branchée dans une
prise femelle correctement mise à la terre car des tensions dangereuses risqueraient
d’atteindre les pièces métalliques accessibles à l’utilisateur.
INFORMATION SUR LE CORDON ÉLECTRIQUE
Utiliser un cordon secteur de 4.5 mètres de long maximum, calibré à 6 ampères minimum,
250V, fabriqué en câblage HAR avec connecteur IEC 32C moulé à une extrémité, et à l’autre
extrémité, une prise de courant mâle répondant aux normes du pays d’utilisation.
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de circuler
librement pour le refroidissement.
TEMPÉRATURE DE FONCTIONNEMENT
Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés
Celsius.
POUR TOUS PAYS : Installer le matériel conformément aux normes électriques nationales et
locales.
TURVALLISUUS
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA
VAROITUS: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa olevia osia.
Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain koulutettu ja pätevä
teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden katkaise sähkövirta tuotteeseen ennen
kuin liität tai irrotat paikallisverkon (LAN) kaapelit.
SALAMANISKUVAARA
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA SALAMOINNIN
AIKANA.
ASENNUS
SÄHKÖ—AUTOMAATTINEN JÄNNITTEENSÄÄTÖ
Tämä tuote säätää automaattisesti mihin tahansa jännitteeseen ohjetarrassa annettujen
arvojen välillä.
SÄHKÖ—TYYPPILUOKAN 1 LAITTEET
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti maadoitettuun
pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa metalliosat vaarallisille
jännitteille.
SÄHKÖ—JOHTOON LIITTYVÄ HUOMAUTUS
Käytä seuraavanlaista virtajohtoa: maksimipituus 4,5 metriä, minimiteho 6 ampeeria, 250 V,
valmistettu HAR-johdostosta, muovattu IEC 320 -liitin toisessa päässä ja käyttömaassa
hyväksytty pistoke toisessa päässä.
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys ympäröivään
huoneilmaan, jotta ilmanvaihto tapahtuisi.
KÄYTTÖLÄMPÖTILA
Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40°C.
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten
mukaisesti.
xii
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
NORME DI SICUREZZA
AVVERTENZE ELETTRICHE
ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne non
sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta solamente
da un tecnico specializzato e qualificato. Per evitare ogni possibilità di SCOSSE
ELETTRICHE, interrompere l’alimentazione del dispositivo prima di collegare o staccare i
cavi LAN.
PERICOLO DI FULMINI
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI
TEMPORALESCHE.
INSTALLAZIONE
ELETTRICITÀ—REGOLAZIONE AUTOMATICA DELLA TENSIONE
Questo prodotto regolerà automaticamente la tensione ad un valore compreso nella gamma
indicata sull’etichetta.
ELETTRICITÀ—DISPOSITIVI DI CLASSE 1
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere inserita in
una presa di corrente specificamente dotata di messa a terra. Una presa non cablata in
maniera corretta rischia di scaricare una tensione pericolosa su parti metalliche accessibili.
ELETTRICITÀ—AVVERTENZA SUL CAVO
Usare un cavo della lunghezza massima di metri 4,5, con capacità minima di 6 A, 250 V, di
filo HAR, dotato di connettore stampato IEC 320 ad un’estremità e di spina approvata dal
paese di destinazione all’altra.
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il libero ricircolo
dell’aria ambiente per il raffreddamento.
TEMPERATURA DI FUNZIONAMENTO
Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative elettriche
nazionali.
SIKKERHET
ELEKTRISITET
ADVARSEL: FARE FOR ELEKTRISK SJOKK
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som brukeren
kan reparere på innsiden. Denne enheten inneholder FARLIGE SPENNINGER, og må kun
åpnes av en faglig kvalifisert tekniker. For å unngå ELEKTRISK SJOKK må den elektriske
strømmen til produktet være avslått før LAN-kablene til- eller frakobles.
FARE FOR LYNNEDSLAG
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
INSTALLASJON
ELEKTRISK—AUTO SPENNINGSTILPASNING
Dette produktet vil automatisk bli tilpasset hvilken som helst strømspenning i de områdene
som vises på etiketten.
xiii
Safety Information (All Products)
ELEKTRISK—TYPE 1- KLASSE UTSTYR
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt jordet
kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig spenninger i lett t
ilgjengelige metalldeler.
ELEKTRISK—MEDDELELSE OM LEDNINGER
Bruk en strømledning av maksimalt 4.5 m. i lengde, godkjent for minst av 6 amp, 250V,
fremstilt av HAR ledning IEC 320 koplingsstykke i den ene enden, og i den andre enden en
plugg som er blitt godkjent i brukerlandet.
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med
romtemperatur for avkjøling.
DRIFTSTEMPERATUR
Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader celsius.
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske
koder.
SEGURANÇA
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que possam ser
consertadas pelo usuário. Este aparelho contém VOLTAGENS PERIGOSAS e só deve ser
aberto por um técnico qualificado e treinado. Para evitar a possibilidade de CHOQUE
ELÉTRICO, desconecte o aparelho da fonte de energia elétrica antes de conectar e
desconectar os cabos da LAN.
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos suscetíveis a
QUEDAS DE RAIO.
INSTALAÇÃO
ELÉTRICO—AJUSTE AUTOMÁTICO DE VOLTAGEM
Este produto ajustar-se-á automaticamente a qualquer voltagem que esteja dentro dos
limites indicados no rótulo.
ELÉTRICO—EQUIPAMENTOS DO TIPO CLASSE 1
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O plugue de
alimentação deve ser conectado a uma tomada com adequada ligação de fio terra. Tomadas
sem adequada ligação de fio terra podem transmitir voltagens perigosas a peças metálicas
expostas.
ELÉTRICO—AVISO SOBRE O CABO DE ALIMENTAÇÃO
Use cabo de alimentação com comprimento máximo de 4,5 metros, com uma capacidade
indicada mínima de 6 amp e 250 V, fabricado de material para cabo HAR com conector
moldado IEC 320 em uma extremidade e, na outra extremidade, um plugue aprovado para
uso no país em questão.
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso livre
ao ar ambiente para arrefecimento adequado do aparelho.
TEMPERATURA DE FUNCIONAMENTO
Este produto foi projetado para uma temperatura ambiente máxima de 40 graus
centígrados.
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais para
instalações elétricas.
xiv
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
SEGURIDAD
AVISOS ELECTRICOS
ADVERTENCIA: PELIGRO DE ELECTROCHOQUE
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el interior
al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES PELIGROSOS y
sólo deberá abrirla un técnico entrenado y calificado. Para evitar la posibilidad de
ELECTROCHOQUE desconecte la corriente eléctrica que llega al producto antes de conectar
o desconectar los cables LAN.
PELIGRO DE RAYOS
PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos o en LOS
CABLES durante TORMENTAS ELECTRICAS.
INSTALACION
ELECTRICO—AUTO-AJUSTE DE TENSION
Este producto se ajustará automáticamente a cualquier tensión entre los valores máximos y
mínimos indicados en la etiqueta.
ELECTRICO—EQUIPO DEL TIPO CLASE 1
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que conectarse a un
enchufe a tierra debidamente instalado. Un enchufe que no está correctamente instalado
podría ocasionar tensiones peligrosas en las partes metálicas que están expuestas.
ELECTRICO—ADVERTENCIA SOBRE EL CABLE
Use un cable eléctrico con un máximo de 4,5 metros de largo, con una capacidad mínima de
6 amperios, 250 V, hecho de cable HAR, con el conector moldeado IEC 320 en un extremo y
con un enchufe que está aprobado por el país de uso final en el otro.
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán tener acceso
libre al aire ambiental de la sala para su enfriamiento.
TEMPERATURA REQUERIDA PARA LA OPERACIÓN
Este producto está diseñado para una temperatura ambiental máxima de 40 grados C.
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos Eléctricos
locales y nacionales.
SÄKERHET
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:
RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det finns inga
delar inuti som behöver underhållas. Denna apparat är under HÖGSPÄNNING och får endast
öppnas av en utbildad kvalificerad tekniker. För att undvika ELEKTRISK STÖT, koppla ifrån
produktens strömanslutning innan LAN-kablarna ansluts eller kopplas ur.
FARA FÖR BLIXTNEDSLAG
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
INSTALLATION
ELEKTRISKT —AUTOMATISK SPÄNNINGSJUSTERING
Denna produkt justeras automatiskt till alla spänningar inom omfånget som indikeras på
produktens märkning.
ELEKTRISKT—TYP KLASS 1 UTRUSTNING
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara ansluten till ett
ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande metalldelar utsätts för
högspänning. Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk.
xv
Safety Information (All Products)
ELEKTRISKT —ANMÄRKNING BETRÄFFANDE KABELN
Använd en kabel med maximum längd 4,5 meter och minimum 6 amp nominal, 250V, av
HAR kabelfabrikat med ett specialutformat IEC 320-kontaktdon i ena änden och i den andra
en plugg som godkänts i landet där produkten används.
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande rumsluft
för avsvalning.
DRIFTSTEMPERATUR
Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader Celsius.
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga bestämmelser för
elektrisk utrustning.
xvi
Table of Contents
Electrical Safety and Installation Requirements For AT-FS724I ..................................... iii
Electrical Safety and Installation Requirements For AT-FS716 and AT-FS716E ............vi
Safety Information (All Products) .......................................................................................ix
Chapter 1
Product Description ..............................................................................................................1
Overview ..................................................................................................................................1
Common Major Features .......................................................................................................2
Physical Description................................................................................................................3
Front Panel LEDs............................................................................................................3
MDI/MDI-X Port ...........................................................................................................4
Power Supply ..................................................................................................................5
Required Voltage ............................................................................................................5
Auto-Negotiation ....................................................................................................................5
Chapter 2
Installation .............................................................................................................................7
Before you Proceed .................................................................................................................7
Verifying Package Contents....................................................................................................7
Site Requirements ...................................................................................................................8
Desktop Installation ................................................................................................................8
Rackmount Installation ..........................................................................................................9
Configuration ..........................................................................................................................9
Standalone Configuration ....................................................................................................10
Cascade Configuration .........................................................................................................10
Uplink Configuration ...........................................................................................................11
Chapter 3
Troubleshooting ..................................................................................................................13
Connectivity Testing .............................................................................................................13
Problem Solving ....................................................................................................................14
Is the unit receiving power?..........................................................................................14
Is the Link/Activity LED lit? .........................................................................................14
xvii
Table of Contents
Appendix A
Switch Specifications ........................................................................................................... 17
Physical Characteristics........................................................................................................ 17
Standards .............................................................................................................................. 17
Cabling Specifications .......................................................................................................... 18
Electrical Specifications........................................................................................................ 18
UTP (RJ45) Connector ........................................................................................................ 18
Network Specifications ........................................................................................................ 19
100Base-TX Cable ................................................................................................................ 19
100Base-TX Connector Pinouts .......................................................................................... 20
Straight-through Cable ................................................................................................ 20
Crossover Cable............................................................................................................ 20
Appendix B
Technical Support Fax Order ............................................................................................. 21
Incident Summary................................................................................................................ 21
Appendix C
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Feedback ....................... 23
Appendix D
Where To Find Us ............................................................................................................... 25
xviii
Chapter 1
Product Description
Overview
This chapter describes the features of the following unmanaged Fast Ethernet
switches:
‰ AT-FS716
‰ AT-FS716E
‰ AT-FS724I
Each switch model is described in Table 1.
Table 1 Switch Models and Port Description
Model
AT-FS716
Description
16 auto-negotiating 10/100 Mbps twisted pair RJ45 ports
Port 16 with MDI/MDI-X push button
Internal Power Supply
AT-FS716E
16 auto-negotiating 10/100 Mbps twisted pair RJ45 ports
Port 16 with MDI/MDI-X push button
External Power Supply
AT-FS724I
24 auto-negotiating 10/100 Mbps twisted pair RJ45 ports
Port 24 with MDI/MDI-X push button
Internal Power Supply
1
Product Description
Note
For definitions of technical terms associated with Allied Telesyn’s products,
refer to the Glossary on Allied Telesyn’s website at www.alliedtelesyn.com.
Common Major Features
These switches come with the following common features:
‰ IEEE 802.3 and IEEE 802.3u compliant
‰ 16 or 24 auto-negotiating 10/100Base-TX ports
‰ RJ45 ports that can be connected/disconnected without powering off the
switch
‰ Store and forward switching at full-wire speed (14,880 packets per
second on 10 Mbps ports and 148,880 packets per second on 100 Mbps
ports)
‰ Media-dependent interface (MDI) push button setting for hub
connection or MDI-X push button setting for PC connection on
Port 16/24
‰ Support for up to 8K MAC addresses
‰ Internal power supply (100-120/200-240VAC) for AT-FS716 and
AT-FS724I, or external power adapter for AT-FS716E
‰ Desktop or rackmounting (rackmount option for AT-FS716 and
AT-FS724I only)
The switch models described in this guide complement the other Allied Telesyn
Fast Ethernet products, providing simple, cost-effective solutions for switching
between 10 and 100 Mbps. Easy to install, simply connect your 10Base-T or
100Base-TX station ports, and plug in the power.
Figures 1 show the front panel of the AT-FS716 switch. The AT-FS716E and
AT-FS724I front panels are similar.
2
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
Figure 1 AT-FS716 Front Panel
Physical Description
The physical description for the switches includes:
‰ Media-Dependent Interface (MDI)/ MDI-X push button setting, Port 16
or Port 24
‰ LEDs
‰ Power supply
Front Panel LEDs
Figure 2 shows the layout of the front panel LEDs; Table 2 describes the LED
status.
3RZHU
/LQNî$FW
ìíí0
)';
ì
ë
ê
é
è
ç
æ
å
Figure 2 A partial view of the Front Panel LEDs
3
Product Description
Table 2
LEDs
Color
POWER
Green
LED Status
Description
Off means there is no power to the switch.
On means there is power to the switch.
LINK/ACTIVITY
Green
On indicates a valid physical link on the port.
Blinking indicates data is being transmitted.
Off means no link.
100M
Green
Off means the speed is 10 Mbps.
On means the speed is 100 Mbps.
FDX (FULL-DUPLEX)
Green
On indicates full-duplex transmission mode.
Off indicates half-duplex transmission mode.
MDI/MDI-X Port
Port 16/24 is associated with the MDI/MDI-X function push button.
The MDI/MDI-X push button gives you the flexibility of using a straight-through
cable to connect to a hub or another switch (Port 16/24 MDI), or to any DTE
device (Port 16/24 MDI-X), such as an end station or a server.
Table 3
Port 16 or Port 24
MDI
MDI-X
4
MDI / MDI-X Push Button
Use
To connect a hub or another switch to the port
To connect a DTE to the port
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
Power Supply
The AT-FS716 and AT-FS724I use a universal internal switching power supply
with 100 to 120 VAC, or 200 to 240 VAC, 50/60 Hz input rating.
Allied Telesyn ships power cords with the units to the U.S., Continental Europe,
and the U.K.
The AT-FS716E uses an external power adapter.
Required Voltage
The switches require input of 100 to 230 VAC. Maximum power consumption is
50W maximum.
Auto-Negotiation
The 10/100 Mbps ports are capable of auto-negotiation:
The ports automatically adapt to the wire speed (10 or 100 Mbps) and duplex
transmission (half- or full-duplex) supported by the linked device without user
reconfiguration.
Auto-negotiation is an optional function of the IEEE 802.3u Fast Ethernet
standard that enables devices (switches) to automatically exchange information
over a link about their speed and duplex abilities. This allows devices to perform
automatic configurations to achieve the maximum common level of operation
over a link. Auto-negotiation can provide automatic speed matching for
multispeed devices at each end of a link. Multispeed Ethernet interfaces can then
take advantage of the highest speed offered by the 10/100 ports on the switch.
The auto-negotiation protocol also includes automatic negotiation of duplex
mode, allowing auto-negotiation-capable end-system devices to not only
configure the speed but also change to full-duplex for even higher traffic
throughput. This is particularly useful in environments where NICs are being
replaced or desktop workstations are moved. Each time a new device is connected
to a switch’s port or a device is moved from one port to another, auto-negotiation
will automatically reconfigure each port without any intervention from a network
administrator.
5
Chapter 2
Installation
Before you Proceed
Before installing the switch, make sure you read “Electrical Safety and Installation
Requirements” starting on page iii.
Verifying Package Contents
Make sure that the package includes the following items:
‰ One AT-FS716, AT-FS716E, or AT-FS724I switch
‰ One AC power cord (AT-FS716 or AT-FS724I) or power adapter
(AT-FS716E)
‰ Two rackmounting brackets with screws (AT-FS716 or AT-FS724I only)
‰ Four self-adhesive rubber feet
‰ Warranty card
‰ This installation guide
If any of the above items is damaged or missing, contact your sales representative
immediately.
7
Installation
Site Requirements
Make sure you observe the following site requirements:
‰ Make sure you are placing the switch in a dust-free and moisture-free
environment.
‰ Do not block ventilation openings on the unit. Allow at least 10 cm (4 in)
of space at the front and back of the unit for ventilation.
‰ Make sure that the switch’s power is accessible and cables can be
connected easily.
‰ Cabling should be away from sources of electrical noise such as radios,
transmitters, broadband amplifiers, power lines, and fluorescent fixtures.
‰ Do not place objects on top of the switch.
‰ Use dedicated power circuits or power conditioners to supply power to
the switch.
Desktop Installation
Place the switch on the desktop using these steps, or perform the steps
“Rackmount Installation” on page 9.
1.
Attach the four self-adhesive rubber feet to the bottom of the switch,
positioning them in the indentations.
2.
Place the switch on a flat, level surface where power is easily accessible.
3.
Connect power:
— For AT-FS716 and AT-FS724I, attach one end of the power cord to
the back of the switch and the other end to the power source.
— For AT-FS716E, plug the power adapter into the power receptacle,
then plug the DC connector to the switch.
Note
The switch performs a self-diagnostic test upon power on, and takes about 20
seconds to complete.
8
4.
Make sure the 3RZHU LED on the front panel lights green.
5.
Attach the data cables and observe normal operation as indicated by the
port LEDs. For Port 16/24, set the MDI/MDI-X push button as required.
AT-FS716, AT-FS716E, and AT-724I Switches Installation Guide
Rackmount Installation
Rackmount installation applies to the AT-FS716 and AT-FS724 only. You will
need a Phillips screwdriver for this installation.
Caution
Do not use power tools to perform this installation.
1.
If previously attached, remove the rubber feet and all cables and power
cord from the switch.
2.
Attach the rackmounting brackets to each side of the switch, using the
screws provided.
3.
Attach the power cord to the back of the switch.
4.
Position the switch in a standard 19-inch rack and secure the switch’s
brackets to the rack using the 4 large screws provided.
5.
Plug the power cord into the power receptacle. Make sure the 3RZHU LED
on the front panel lights green.
6.
Attach the data cables and observe normal operation as indicated by the
port LEDs. For Port 16/24, set the MDI/MDI-X switch as required. For
typical configuration information, refer to “Configuration” on page 9.
You are finished with rackmount installation.
Configuration
Note
Auto-negotiation for transmission mode supports full-duplex only if the
connected device also negotiates for full-duplex transmission mode.
The following sections discuss standalone, cascade and uplink configurations.
9
Installation
Standalone Configuration
Figure 3 shows the switch connected to end stations and a server. The basic
physical connection for this configuration requires connecting one of the switch’s
ports to the adapter card of an end station.
Cat 5, UTP wiring
Figure 3 AT-FS716 Connected to End Stations
Cascade Configuration
Cascading means that two switches can be connected together using any of the
switch ports provided you maintain the same medium type. Two switches can be
cascaded to support multiple network port connections. Cable length to the nodes
must follow the 100Base-TX cabling specifications.
To cascade installed switches, do the following:
Note
When cascading switches, you must use the same medium type from port to
port.
10
1.
If you intend to use Port 16/24, set the MDI/MDI-X push button to the
MDI position (in).
2.
Use a straight-through UTP RJ45 cable to connect the first switch to the
second switch. See Figure 4.
AT-FS716, AT-FS716E, and AT-724I Switches Installation Guide
Port 16 MDI
100 Mbps
Figure 4 Cascading Switches
3.
Check the front panels to make sure that the green /LQNî$FWLYLW\ýLED
lights.
Uplink Configuration
For 100 Mbps connection to the backbone, use Port 16/24 with the switch set for
0',ñýDQGýCategory 5 UTP cableï
11
Chapter 3
Troubleshooting
This chapter describes the procedures to test and troubleshoot the switches.
Connectivity Testing
In the following procedure, you will test each port for a valid connection and to
confirm the correct operation of the network.
1.
Start with Ports 1 and 2. Connect these two ports of a single switch to two
nodes or workstations and turn on the switch power.
2.
Wait approximately 1-3 seconds for the auto-negotiation process to
complete after power-on or after the cables are reconnected.
3.
Make sure the Link/Activity and other LEDs of both switch ports are lit.
4.
After confirming that Port 1 and Port 2 are operational, reconnect one of
the nodes/workstations to another port, then repeat this connectivitiy
test with the switch’s remaining ports. Continue to verify the connection
in each port by checking the Link/Activity and other activity LEDs.
Note
Use Port 16/24 with the push button set for MDIð; to connect to a
workstation, or MDI to connect to a hub or switch.
13
Troubleshooting
Problem Solving
Is the unit receiving power?
Check the Power LED on the front of the switch. This green LED should be lit.
Note
The switch performs a self-diagnostic test upon power on, and takes
about 20 seconds to complete.
If the Power LED is not on, check both ends of the power cord or adapter. Make
sure the power cord or adapter is plugged into a functioning wall outlet and that
it is properly inserted into the switch’s connector on the back of the unit.
Is the Link/Activity LED lit?
The Link LED on the front of the switch lights when a proper connection between
the corresponding 10/100Base-TX port and the equipment connected to it is
established. If this LED is not lit, check for the problems listed below and make
corrections as necessary.
1.
Problem 1:
The cable has been cut, damaged, or it is the wrong type of cable.
‰ Solution 1:
— Try making the connection with a different cable. Be sure you
are using an undamaged cable of the correct type.
2.
Problem 2:
Connected equipment is not turned on or not operating properly.
‰ Solution 2:
— Check the connected equipment (computer, another switch,
etc.) and turn on the power.
14
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
3.
Problem 3:
Port 16/24 does not work.
‰ Solution 3:
— Make sure you have the correct MDI/MDI-X push button
setting for Port 16/24. Use MDI for uplink, MDI-X for a PC.
4.
Problem 4:
There is data loss between the switch and one of the connected network
nodes.
‰ Solution 4:
— Make sure that the distance between the switch and the
connected network device is no greater than 100 m (328 ft).
— Make sure you are using Category 5 cable for 100 Mbps
operation.
15
Appendix A
Switch Specifications
Physical Characteristics
Chassis Dimensions:
WxDxH
AT-FS16
330 mm x 203 mm x 44 mm
(13 in x 8 in x 1.72 in)
AT-FS16E
330 mm x 203 mm x 44 mm
(13 in x 8 in x 1.72 in)
AT-FS24I
440 mm x 305 mm x 44 mm
(17.36 in x 12 in x 2.5 in)
Weight:
AT-FS716
4.75 lbs (2.16 kg)
AT-FS716E
4.4 lbs (2.0 kg)
AT-FS724I
5.5 lbs (2.5 kg)
Operating temperatures:
0° to 40° C (32° to 104° F)
Storage temperatures:
-40° to 70° C (-40° to 158° F)
Relative humidity:
5% to 95% (non-condensing)
Operating altitude:
Up to 3,048 m (10,000 ft)
Standards
CE Compliant
Functional:
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u, 100Base-TX Fast Ethernet
EMI/RFI:
AT-FS716 and AT-FS716E: Meets FCC Class B,
VCCI Class B, CISPR Class B
AT-FS724: Meets FCC Class A, VCCI CLass A,
CISPR Class A
17
Switch Specifications
Safety:
Conforms to all standards normally supported
by Allied Telesyn products, including safety
standards UL 1950, CSA/NRTL (C22.2 950, UL
1950),TUV/GS (EN60950)
Immunity:
IEC 1000-4-2/3/4/6
Cabling Specifications
10Base-T:
STP/UTP Category 3,4,5 100 ohm impedance
100Base-TX:
STP/UTP Category 5 wiring, 100 ohm
impedance
100 m (328 ft) is the maximum distance between switch and network node
connections.
Electrical Specifications
AT-FS716 or AT-FS724I Internal Power:
Internal universal power supply with 100 to 240
VAC, 50/60 Hz, 0.3 A input.
AT-FS716E External Power: External power adaper provides 13-19 UDC,
800 mA maximum.
UTP (RJ45) Connector
Figure 5 shows an RJ45 connector. For a 100Base-TX link between two switches,
—any two Medium Attachment Units (MAUs)—you typically need a crossover
cable. For a connection to a Network Interface Controller (NIC), the cable is wired
straight-through in accordance with applicable standards.
Pin 1
Pin 8
Figure 5 RJ45 Connector
18
AT-FS716, AT-FS716E, and AT-FS724I Switches Installation Guide
Network Specifications
Table 4 provides an overview of IEEE 802.3 and 802.3u specifications for 10Base-T
and 100Base-TX network configurations using shielded twisted-pair wiring.
Table 4 IEEE 802.3 and 802.3u Network Specifications
10Base-T
100Base-TX
Media
Unshielded Twisted Pair/
Shielded Twisted Pair
Category 3 or 5
Unshielded Twisted Pair/
Shielded Twisted Pair
Category 5 only
Topology
Star, Tree
Star, Tree
External Devices
Network Adapter Card,
Repeater, Switch
Network Adapter Card,
Repeater, Switch
Maximum Segment Length
100 m (328 ft)
100 m (328 ft)
100Base-TX Cable
There are various grades of voice-quality and data-quality cables available. These
can appear to be similar externally, although their high-speed data transmission
characteristics are radically different.
The identification problem is made worse by some suppliers selling voice-quality
cables as data-quality cables.
If voice-quality cables are used in a 100Base-TX network system, data movement
may be slow, collision-prone or non-existent. In addition, interface LEDs will
usually indicate a valid link in such cases.
Category 5 is required cabling for use with 100Base-TX connections. Using any
other category for a 100Base-TX connection may have high error rates and may
not have the capacity to transmit data.
19
Switch Specifications
100Base-TX Connector Pinouts
Straight-through Cable
4#7;.
5#7;0
6#5;.
7;.4
7;0#5
5;.6
9#5;0
5;0#9
4#7;.
5#7;0
6#5;.
7;.4
7;0#5
5;.6
9#5;0
5;0#9
Crossover Cable
20
Appendix B
Technical Support Fax Order
Name ___________________________________________________________________
Company ________________________________________________________________
Address _________________________________________________________________
City ________________________ State/Province ________________________________
Zip/Postal Code ___________________ Country_________________________________
Phone _______________________________Fax_________________________________
Incident Summary
Model number of Allied Telesyn product I am using ______________________________
Network software products I am using _________________________________________
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
Brief summary of problem __________________________________________________
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
Conditions (List the steps that led up to the problem.) ____________________________
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
Detailed description (Use separate sheet, if necessary)
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
When completed, fax this sheet to the appropriate Allied Telesyn office. Fax numbers can
be found on page 25.
21
Appendix C
AT-FS716, AT-FS716E, and AT-FS724I
Switches Installation Feedback
Please tell us what additional information you would like to see discussed in the
guide. If there are topics you would like information on that were not covered in
the guide, please photocopy this page, answer the questions and fax or mail this
form back to Allied Telesyn International Corp. The mailing address and fax
number are at the bottom of the page. Your comments are valuable when we plan
future revisions of the guide.
I found the following the most valuable ________________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
I would like the following more developed _____________________________
_______________________________________________________________
_______________________________________________________________
_______________________________________________________________
I would find the guide more useful if __________________________________
_______________________________________________________________
_______________________________________________________________
Please fax or mail your feedback. Fax to 1-408-736-0100. Or mail to:
Allied Telesyn International, Corp.
c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
PN 613-10804-00 Rev. A
23
Appendix D
Where To Find Us
For Technical Support or Service
Location
Phone
Fax
Americas
United States, Canada, Mexico, Central America,
South America
1 (800) 428-4835
1 (918) 628-3222
Asia
Singapore, Taiwan, Thailand, Malaysia, Indonesia,
Korea, Philippines, China, India
(+65) 3815-613
(+65) 3833-830
Australia
Australia, New Zealand
(+61) 2-943-5111
(+61) 2-9438-4966
France
France, Belgium, Luxembourg, The Netherlands,
Middle East, Africa
(+33) 1-60-92-15-32
(+33) 1-69-28-37-49
Germany
Germany, Switzerland, Austria, Eastern Europe
(+49) 30-435-900-126
(+49) 30-435-70-650
Hong Kong
(+852) 2-529-4111
(+852) 2 529-7661
Italy
Italy, Spain, Portugal, Greece, Turkey, Israel
(+39) 02-416047
(+39) 02-419282
Japan
(+81) 3-3443-5640
(+81) 3-3443-2443
United Kingdom
United Kingdom, Denmark, Norway, Sweden, Finland,
Iceland
(+44) 1-235-442560
(+44) 1-235-442680
Technical Bulletin Board Service
1 (425) 483-7979
Technical Support E-mail Address
TS1@alliedtelesyn.com
CompuServe
Go ALLIED
FTP Server
$GGUHVVã IWSïDOOLHGWHOHV\QïFRPý>ORZHUFDVHýOHWWHUV@
/RJLQã DQRQ\PRXVý>ORZHUFDVHýOHWWHUV@
3DVVZRUGã \RXUýHðPDLOýDGGUHVVý>UHTXHVWHGýE\ýWKHýVHUYHUýDWýORJLQ@
For Sales or Corporate Information
Allied Telesyn International, Corp.
19015 North Creek Parkway
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Allied Telesyn International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: 1 (800) 424-4284 (USA and Canada)
Fax: 1 (408) 736-0100
World Wide Web:
http://www.alliedtelesyn.com
25
Download PDF