Sharp | 19U-M100 | Service manual | Sharp 19U-M100 Service manual

19U-M100,19U-M100S
CU19M10
SERVICE MANUAL
S12E719U-M100
COLOR TELEVISION
Chassis No. SN-010
POWE
R
– VOL
+
CH
MENU
MODELS
19U-M100, 19U-M100S
CU19M10
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
»
»
»
»
»
»
»
»
»
»
Page
ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
LOCATION OF USER'S CONTROL ..................................................................................................... 6
INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 7
CHASSIS LAYOUT ............................................................................................................................. 13
BLOCK DIAGRAM .............................................................................................................................. 15
SCHEMATIC DIAGRAMS ................................................................................................................... 17
PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 26
REPLACEMENT PARTS LIST ............................................................................................................ 29
PACKING OF THE SET ...................................................................................................................... 37
ELECTRICAL SPECIFICATIONS
POWER INPUT ..................................................... AC 120 V, 60 Hz
POWER RATING .................................................................... 69 W
PICTURE SIZE ........................................... 1,194cm2 (185sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency ...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING ..................................................... 1 W (RMS)
SHARP CORPORATION
SPEAKER
SIZE ...................................................................... 8 cm (Round)
VOICE COIL IMPEDANCE ............................. 32 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ..................................................... 75 ohm Unbalanced
TUNING RANGES
VHF-Channels ............................................................... 2 thru 13
UHF-Channels ............................................................ 14 thru 69
CATV Channels ........................................................... 1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
This document has been published to be used for after
sales service only.
1 The contents are subject to change without notice.
19U-M100,19U-M100S
CU19M10
IMPORTANT SERVICE SAFETY PRECAUTION
Ë Service work should be performed only by qualified service technicians who are thoroughly
familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
-no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
with a meter to be certain that the high voltage does
not exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified
or make unrecommended circuit modifications to the
high voltage circuitry.
6. When troubleshooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
4A 125V
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE ONLY
WITH SAME TYPE 4A-125V
FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
2
19U-M100,19U-M100S
CU19M10
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
» Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
» Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
» Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground.
» Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
1.5k ohm
10W
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
19U-M100,19U-M100S
CU19M10
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ë
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
LIMITES DES RADIATIONS X ET DE LA
HAUTE TENSION
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs
peuvent présenter un danger de choc électrique
lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur a deux systèmes de mise
à la terre qui sont séparés par un matériau isolant.
Le système de mise à la terre non-isolée (chaud)
est pour le circuit du régulateur de tension B+ et le
circuit de sortie horizontale. Le système de mise à
la terre isolé est pour les basses tensions C. C. B+
et le circuit secondaire du transformateur de haute
tension.
P R E C AU T I O N : P O U R L A
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
4A 125V
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE 4A-125V.
1. Tout le personnel réparateur doit être instruit des
instructions et procédés relatifs aux radiations X.
Le tube-image, seule source de rayons X dons les
téleviseurs transistorisés, n'émet pourtant pas de
rayons mesurables si la haute tension est maintenue
à un niveau préconisé dans la section "Vérification
de la haute tension".
C'est seulement quand la haute tension est
excessive que les rayons X peuvent entrer dans
l'enveloppe du tube-image y compris le conducteur
de verre. Il est important de maintenir la haute tension
en-dessous du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un
vo l t m è t r e à h a u t e t e n s i o n q u i d o i t ê t r e
périodiquement étalonné.
3. La haute tension doit toujours être maintenue à la
valeur de régime-et pas plus haute. L'opération à
des tensions plus élevées peut entraîner une panne
du tube-image ou du circuit à haute tension et, dans
certaines conditions, peut entraîner une radiation
dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne
correctement, il n'y a aucun problème de radiation
X. Chaque fois qu'un châssis couleurs est réparé, la
luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
que la haute tension ne dépasse pas la valeur
spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures
d'essai sur un récepteur qui présente une haute
tension excessive, éviter de s'approcher inutilement
du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
que nécessaire pour localiser la cause de la tension
excessive.
REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme,
supprimer la charge statique en branchant
une résistance de 10 k en série a vec un fil
isolé (comme une sonde d'essai) entre la
mise à la terre du tube-image et le fil
d'anodel. (Le corden d'alimentation doit être
retiré de la prise murale.)
1. Il est à noter que le tube-image de ce récepteur est
intégralement protégé contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.
4
19U-M100,19U-M100S
CU19M10
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
» Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
arbres de commande et des boutons, écusson, etc.)
et mesurer la chute de tension CA en-travers de la
résistance.
Toutes les vérifications doivent être refaites après
avoir inversé la fiche du cordon d'alimentation. (Si
nécessaire, une prise d'adpatation non polarisée peut
être utilisée dans le but de terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme
les boutons de commande non-métalliques, les
isolants, le dos du coffret, les couvercles ou blindages
de réglage et de compartiment, les réseaux de
résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
» Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
» A l'aide de deux fils à pinces, brancher une résistance
de 1,5 kΩ 10 watts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à
la terre.
» Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
de la résistance.
Voltmètre CA
1.5k ohm
10W
0.15µF
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
BRANCHER A UNE
TERRE CONNUE
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentes
à vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
5
19U-M100,19U-M100S
CU19M10
LOCATION OF USER'S CONTROL
Front Panel
POWER
– VOL +
CH
MENU
SENSOR AREA FOR
REMOTE CONTROL
POWER
– VOL +
CH
MENU
POWER
Press → On.
Press again → Off.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
CHANNEL UP/DOWN – MENU
(') Selects next higher channel.
(") Selects next lower channel.
• Press both at the same time to
access the MAIN MENU screen.
Basic Remote Control Functions
Infrared Transmitter Window
INPUT
Press → Switch to external video input
mode.
Press again → Switch to TV mode.
POWER
Press → On.
Press again → Off.
REMOTE KEYPAD
Accesses any channel from keypad.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
• Moves the “
” mark of the MENU
screen.
FLASHBACK
Returns to previous channel.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
MUTE
Press → Mutes sound.
Press again → Restores sound.
• CLOSED CAPTION appears when
sound is muted.
DISPLAY
Press → Displays receiving channel for
four seconds.
Press again → Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.
TV
6
19U-M100,19U-M100S
CU19M10
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly
tuned in test signal.
3. Enter the service mode and select the service
adjustment "S03" and Bus data "01" (Y-mute on).
4. The voltage should be approximately 26.0kV (at zero
beam).
If a correct reading cannot be obtained, check
circuitry for malfunctioning components. After the
voltage test, make Y-mute off to the normal mode.
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for
accurate input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 21.4 ±1.5 V.
5. Apply external 27.2V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before
the set is returned to the customer.
7
19U-M100,19U-M100S
CU19M10
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage. Follow
the steps below whenever the service adjusment is required.
To enter the service mode and exit service mode.
While pressing the Vol-up and Ch-up buttons at the sametime, plug the AC cord into a wall socket.
Now, the TV set is switched on and enters the service mode.
To exit the service mode, turn the television off by pressing the power button.
1. Service mode.
Before putting unit into the service mode, check that customer adjustments are in the normal mode. Use the reset
function in the video adjustment menu to ensure customer control are in their proper (reset) position.
2. Service number selection.
In the service mode, you will see the window screen as window 1. There are 3 adjustment categories 2DEF,
3SIGNAL, 4FIX VALUE as show in Figure A.
Window 2: DEF
D01
D03
D05
Window 3: SIGNAL
D02
D04
D06
DEF
S01
SIGNAL
S02
S12
S13
RETURN
RETURN
Window 1: ADJUSTMENT CATEGORIES
SERVICE MODE
DEF
SIGNAL
FIX VALUE
EEPROM
RETURN
RETURN
RETURN
FIX VALUE
Window 4: FIX VALUE
F01
F02
F15
F16
F25
F26
NEXT
F13
F14
RETURN
NEXT
PREVIOUS
RETURN PREVIOUS
Figure A: ADJUSTMENT CATEGORIES
Press CH UP/DOWN button for selection and enter by VOL UP or VOL DOWN.
Press CH UP/DOWN button to select the adjustment item and VOL UP/DOWN
to adjust the data number for each categories.
(OSD disturbance can be erased by R/C display key)
(Note: EEPROM – factory used only)
8
19U-M100,19U-M100S
CU19M10
Below are the adjustments ranges and initial values for FIX VALUE category.
FIX VALUE
SERVICE
POSITION
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
DATA
ADJUST ITEM
OPTION 1
OPTION 2
E-SAVE
TUNER SETUP
R-TONE RD
R-TONE BD
B-TONE RD
B-TONE BD
FM LEVEL
AFC GAIN
G DRIVE
FBT BLK SW
V COMP
OSD CONT
SHARPNESS
FLT SYS
KILLER OP
PRE SHOOT
CORING
DC REST
BS START
BS GAIN
ABL START
R/B ANGLE
H BLK R
H BLK L
RANGE
INITIAL VALUE
(Hex)
00-FF
00-FF
00-3F
00, 01
00-7F
00-7F
00-7F
00-7F
00-1F
00, 01
00, 0F
00, 01
00-07
00-07
00-3F
00-03
00-07
00-03
00-07
00-03
00-03
00-03
00-07
00-0F
00-07
00-07
B0
04
23
00
19
00
00
12
0C
00
0F
01
07
02
19
00
04
03
07
02
01
01
00
08
04
04
B0(19U-M100/100S),A0(CU19M10)
04
2A
00
03
7C
00
04
0C
00
0F
01
07
00
19(Matsushita Tuner),11(SHARP Tuner)
00
02
00
04
02
01
01
00
08
03
00
Table - A
Below are the ranges and initial values for each adjustment and in each categories.
DEF
SERVICE
POSITION
D01
D02
D03
D04
D05
D06
ADJUST ITEM
H-PHASE
V-SIZE
V-POSITION
CC-POSITION
V-LINEARITY
V-S-CORRECTION
DATA
RANGE
INITIAL VALUE
00-1F
00-7F
00-3F
00-FF
00-1F
00-1F
0C
40
20
1A
10
10
ADJUSTMENT CONTENTS
Must be "20"
Must be "18"
Must be "0C"
Table - B
SIGNAL
SERVICE
POSITION
S01
S02
ADJUST ITEM
DATA
RANGE
INITIAL VALUE
RF AGC
VIDEO LEVEL
00-3F
00-07
14
03
S03
Y-MUTE
00-03
00
S04
S05
S06
S07
S08
S09
S10
S11
S12
S13
SUB BIAS
R-BIAS
G-BIAS
B-BIAS
R-DRIVE
B-DRIVE
CONTRAST
TINT
COLOR
BRIGHTNESS
00-FF
00-FF
00-FF
00-FF
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
40
00
00
00
53
53
5A
40
40
40
ADJUSTMENT CONTENTS
"01":Y-MUTE, "02":V-STOP&Y-MUTE
"03":Activate color killer
Must be "30"
Note: Refer to the SERVICE ADJUSTMENT for each corresponding values.
Table - C
9
19U-M100,19U-M100S
CU19M10
Holding down both the Vol-up/Ch-down buttons on the TV set at service mode for more than 2 seconds will automatically
write the above initial values into IC2101.
ADJUSTMENT
PART REPLACED
NECESSARY
X
IC2001
IC201
X
IC2101
X
CRT
X
NOTES
UNNECESSARY
Data is stored in IC2101.
The adjustment is needed to compensate for characteristics
of parts including IC201.
Holding down both the Vol-up/Ch-down buttons on the TV set
in the service mode for more than 2 seconds will automatically
write the above initial values into IC2101.
Adjust items related to picture tube only.
Table - D
10
19U-M100,19U-M100S
CU19M10
Ë SERVICE ADJUSTMENT
RF AGC Adjustment
White Balance Adjustment
1. Receive a good local channel.
2. Enter the service mode signal category and select
the service adjustment "S01".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.
Note: You have to exit the service mode first to
select another channel.
1. Receive a good local channel.
2. Select the service adjustment "S12" and set the data
value to "00" to set the color level to the minimun.
You may skip this step, if you selected a B/W picture
or monoscope.
3. Alternately adjust the service adjustment data of
"S08" and "S09" until a good grey scale with normal
white is obtained.
4. Select the service adjustment "S12" and reset data
to obtain normal color level.
Video Level (TV Det Video Level)
Adjustment
Sub-Picture Adjustment
1. Receive a good local channel.
2. Make sure the customer picture control is set to
maximum.
3. Enter the service mode and select the service
adjustment "S10".
4. Adjust the data value to achieve normal contrast
range.
1. Receive a good local channel.
2. Enter the service mode signal category and select
the service adjustment "S02".
3. Set the data value to "02" first, then adjust the data
in ranges 02 ±2 step to obtain a normal contrast level.
Screen Adjustment
1. Connect to oscilloscope probe between TP855 and
ground of the CRT unit.
2. Receive a good local channel.
3. Enter the service mode Signal category and set the
service adjustment "S04" to step 30. Then select the
service adjustment "S12" and set the data value to
"00" to set the color level to the minimum level. (record
the original data first). You may skip this step, if you
selected a B/W picture or monoscope pattern. Set
also the "S05/S06/S07" data to minimum level.
4. Select the service adjustment "S03" and set the data
value to "01" to turn off the luminance signal (Y-mute).
5. Select the service adjustment "S13" and adjust the
data value to obtain 2.35 volts as shown in Figure B.
6. Adjust the master screen control until the raster
darkens to the point where raster is barely seen.
7. Adjust the service adjustment "S05" red, "S06" green
and "S07" blue to obtain a good grey scale with
normal white at low brightness level.
8. Select the service a adjustment "S03" and reset data
to "00". Select the service adjustment "S12" and reset
data to obtain normal color level.
9. Remove probe and reset the master screen control
to obtain normal brightness range.
Sub-Tint Adjustment
1. Receive a good local channel.
2. Set the customer tint control to the center of it’s range.
3. Enter the service mode and select the service
adjustment "S11".
4. Adjust "S11" data value to obtain normal fresh tones.
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center
position.
3. Enter the service mode and select the service
adjustment "S12".
4. Adjust "S12" data value to obtain normal color level.
Sub-Brightness Adjustment
1. Receive a good local channel.
2. Make sure the customer brightness control is set to
center position.
3. Enter the service mode and select the service
adjustment "S13".
4. Adjust "S13" data value to obtain normal brightness
level.
2.35 Vdc
GND
Figure B: WAVEFORM FOR SCREEN ADJUSTMENT
11
19U-M100,19U-M100S
CU19M10
Vertical-Size, V-Linearity and
V-S Correction Adjustments
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D02" for Vertical Size, "D05" for VLinearity and "D06" for V-S Correction Adjustment.
3. Set in order "D05" for V-Linearity, "D06" for V-S
Correction and set the data to get the best linearity.
4. Then adjust "D02" data until it become a proper
vertical size.
Horizontal Position Adjustment
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D01".
3. Adjust "D01" data value to center the picture.
Vertical-Phase Adjustment
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D03".
3. Adjust "D03" bus data to get the most acceptable
vertical position.
Note: The step range is 20 (032) ±10 steps.
Caption Position Adjustment (Horizontal)
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D04".
3. A black text box will appear on the screen. (see
Figure C. below)
4. Adjust "D04" data value to balance the text box
position in the center (A=B).
A
B
Figure C.
12
19U-M100,19U-M100S
CU19M10
MODELS 19U-M100/100S CHASSIS LAYOUT
H
Ë19U-M100
Ë19U-M100S
G
F
E
D
C
B
A
1
2
3
4
13
5
6
19U-M100,19U-M100S
CU19M10
MODEL CU19M10 CHASSIS LAYOUT
H
G
F
E
D
C
B
A
1
2
3
4
14
5
6
19U-M100,19U-M100S
CU19M10
MODELS 19U-M100/100S BLOCK DIAGRAM
H
G
F
E
D
C
B
A
1
2
3
4
15
5
6
19U-M100,19U-M100S
CU19M10
MODEL CU19M10 BLOCK DIAGRAM
H
G
F
E
D
C
B
A
1
2
3
4
16
5
6
19U-M100,19U-M100S
CU19M10
DESCRIPTION OF SCHEMATIC DIAGRAM
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µF, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
å
ç
AND SHADED (
) COMPONENTS
= SAFETY RELATED PARTS.
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES åET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE ç : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
WAVEFORMS
1.0
1.0
0.9
5.0
5.0
2.1
1.0
1.2
25
47
4.6
0.7
33
39.0
1160
220
150
133
220
1.7
0.7
1.4
105
95
105
17
19U-M100,19U-M100S
CU19M10
MODEL 19U-M100 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
1
2
3
18
4
5
6
7
8
9
10
11
19
12
19U-M100,19U-M100S
CU19M10
MODEL 19U-M100S SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
1
2
3
20
4
5
6
7
8
9
10
11
21
12
19U-M100,19U-M100S
CU19M10
MODEL CU19M10 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
1
2
3
22
4
5
6
7
8
9
10
11
23
12
19U-M100,19U-M100S
CU19M10
MODEL 19U-M100 SCHEMATIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
1
2
3
4
24
5
6
19U-M100,19U-M100S
CU19M10
MODELS 19U-M100S, CU19M10 SCHEMATIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
1
2
3
4
25
5
6
19U-M100,19U-M100S
CU19M10
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
1
2
3
4
26
5
6
19U-M100,19U-M100S
CU19M10
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Chip Parts Side)
A
1
2
3
4
27
5
6
19U-M100,19U-M100S
CU19M10
H
G
F
PWB-B: CRT Unit (Wiring Side)
E
D
C
B
PWB-B: CRT Unit (Chip Parts Side)
A
1
2
3
4
28
5
6
19U-M100,19U-M100S
CU19M10
Ref. No.
★
Part No.
Description
Code
Ref. No.
PARTS LIST
Part No.
★
Description
Code
LISTE DES PIECES
PARTS REPLACEMENT
CHANGE DES PIECES
Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are
identified by å and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. The use of a substitute replacement part which
does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create
shock, fire or other hazards.
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp
éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces
élelectriques qui pr élesentent ces particularit éles, sont rep éler élee
par la marque å et sont hachur élees dans les listes de pi`eces et dans
les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente
pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece
recommand élee parl'usine et dans ce manuel de service, peut provoquer
une éLelectrocution, un incendie ou toutautre sinistre.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER
3. PART NO.
in USA:
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
2. REF. NO.
4. DESCRIPTION
1. NUMERO DU MODELE
2. NO. DE REF
3. NO. DE PIECE
4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
Contact your nearest SHARP Parts Distributor to order. For
location of SHARP Parts Distributor, Please call Toll-Free; 1800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
'
Ref. No.
★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE
MARK: X-RAY RELATED PARTS
★
Part No.
Description
'
Code
Ref. No.
MARQUE: PIECES RELATIVE AUX RAYONS X
Part No.
★
Description
PSPAG0017PEZZ R Spacer, x3
QEARC1913PEZZ R Grounding Strap
PICTURE TUBE
Code
AC
AF
19U-M100
'å
'å
å
V101 VB48LRH93X/~S
DY601 RCiLH0201PEZZ
L703 RCiLG0099PEZZ
or
RCiLG0108GJZZ
or
RCiLG0014MEZZ
LHLDW0003PEKZ
LHLDW1033PEZZ
PMAGF3045CEZZ
PSPAG0017PEZZ
QEARC1913PEZZ
J Picture Tube
R Deflection Yoke
R Degaussing Coil
CC
AZ
AL
R
J
J
R
R
AB
AA
AG
AC
AF
PRINTED WIRING BOARD ASSEMBLIES
Wire Holder, x4
Holder
Purity Magnet
Spacer, x3
Grounding Strap
(NOT REPLACEMENT ITEM)
19U-M100
PWB-A DUNTKA358WEX9 – MAIN Unit
PWB-B DUNTKA359WEV2 – CRT Unit
—
—
19U-M100S
PWB-A DUNTKA358WEY0 – MAIN Unit
PWB-B DUNTKA359WEV1 – CRT Unit
19U-M100S, CU19M10
VB48KRD89X/4E
or
VB48KRD89X/3E
or
VB48QAD220X~S
or
VB510CKAY1S-S
' å DY601 RCiLHA021WJZZ
or
RCiLH0100MEZZ
or
RCiLH0148PEZZ
or
RCiLH0147PEZZ
å L703
RCiLG0099PEZZ
or
RCiLG0108GJZZ
or
RCiLG0014MEZZ
LHLDW0003PEKZ
LHLDW1033PEZZ
PMAGF3046CEZZ
'å
V101
R CRT(DY601:HA021WJ)
CU19M10
CB
PWB-A DUNTKA358WEY1 – MAIN Unit
PWB-B DUNTKA359WEV1 – CRT Unit
CRT(DY601:H0100ME)
CRT(DY601:H0147PE)
CRT(DY601:H0148PE)
R DY(V101:A48KRD89X/4E)
BB
DY(V101:A48KRD89X/3E)
DY(V101:CPJ510CKAY1S)
DY(V101:A48QAD220X)
R Degaussing Coil
AL
R Wire Holder, x4
J Holder
R Purity Magnet
AB
AA
AF
—
—
29
—
—
19U-M100,19U-M100S
CU19M10
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT
or
VS2PD601ARQ-1
Q2211 VS2SC1623L61E
or
VS2SC3928R/-1
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å TU51 VTUVTST5UF770
J Tuner
or
VTUENV56D82-1
IC771
IC2001
IC2040
IC2101
RH-iX3354CEN1
J LA76843N
VHiAN7511//-1
J AN7511
VHiLA7840//-1
J LA7840
VHiTEA1507/-1
J TEA1507P/N1
RH-FX0034CEZZ J PC817
or
RH-FX0002GEZZ
or
RH-FX0029CEZZ
VHiKA7805AP-1
J KA7805API
or
VHiTA7805S/-1
RH-iX3492CEZZQ R TMPA8700CPF
VHiPST994C/-1
J PST994C
VHiM24C16B/-1
J M24C16-BN6
or
VHiBR24C16-1
AZ
D353
D453
D455
AT
AK
AR
AL
AE
D456
D457
D458
D459
AE
D502
D511
D632
D641
' å D651
å D653
å D661
AU
AD
AG
TRANSISTORS
Q101
VS2SC945AQ/-1
or
VS2SC3198Y/-1
Q201 VS2SC2735//1E
Q451 VS2SA812-M51E
or
VS2SA1530R/-1
Q452 VS2SA1266-Y-1
Q601 VS2SC2482//-1
å Q602 VS2SD2586//1E
Q631 VS2SC945AQ/-1
or
VS2SC3198-Y-1
å Q701 VSSPP04N60C-1
or
VSSPP07N60C-1
or
VS2SK2708//1E
or
VS2SK2645//-G
or
VSSTP6NC60+-1
or
VSSTP6NC60FP
or
VSSTP7NB60FP
å Q701 VS2SK2645++-1
or
VS2SK2708//1E
Q702 VS2SC945AQ/-1
or
VS2SC3198Y/-1
or
VS2SC1815Y/-1
Q751 VS2SC945AQ/-1
or
VS2SC3198-Y-1
Q752 VS2SC945AQ/-1
or
VS2SC3198-Y-1
Q2201 VS2SC1623L61E
or
VS2SC3928R/-1
J 2SC945AQ
AB
J 2SC2735
J 2SA812
AC
AC
J
J
J
J
AA
AD
AM
AB
2SA1266-Y
2SC2482
2SD2586
2SC945AQ
J SPP04N60C
(19U-M100, 19U-M100S)
Description
J 2SC1623
Code
AB
DIODES
D52
D101
D352
INTEGRATED CIRCUITS
IC201
IC351
å IC501
å IC701
å IC702
'å
★
Part No.
å
D701
å
D702
å
D703
å
D704
AH
D705
D707
D708
J 2SK2645 (CU19M10)
AN
J 2SC945AQ
AB
J 2SC945AQ
AB
J 2SC945AQ
AB
J 2SC1623
AB
å
å
D709
D712
å
D717
D725
D726
D740
D751
D752
30
RH-EX0676GEZZ
RH-EX0616GEZZ
RH-DX0048GEZZ
or
VHD1SS119//-1
RH-EX0644GEZZ
RH-EX0616GEZZ
RH-DX0048GEZZ
or
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-EX0644GEZZ
RH-EX0644GEZZ
RH-DX0048GEZZ
or
VHD1SS119//-1
RH-DX0131CEZZ
RH-DX0441CEZZ
RH-EX0630GEZZ
RH-EX0630GEZZ
VHD1SS244//-1
RH-EX0667GEZZ
RH-DX0468CEZZ
or
RH-DX0229CEZZ
or
RH-DX0302CEZZ
RH-DX0490CEZZ
or
RH-DX0154CEZZ
RH-DX0490CEZZ
or
RH-DX0154CEZZ
RH-DX0490CEZZ
or
RH-DX0154CEZZ
RH-DX0490CEZZ
or
RH-DX0154CEZZ
RH-DX0048GEZZ
or
VHD1SS119//-1
RH-DX0475CEZZ
or
VHD1SS244//-1
RH-DX0475CEZZ
or
VHD1SS244//-1
RH-DX0229CEZZ
RH-DX0487CEZZ
or
RH-DX0302CEZZ
or
RH-DX0468CEZZ
or
RH-DX0487CEZZ
or
RH-DX0513CEZZ
RH-EX0616GEZZ
RH-DX0131CEZZ
RH-DX0048GEZZ
or
VHD1SS119//-1
RH-DX0048GEZZ
or
VHD1SS119//-1
RH-EX0611GEZZ
RH-DX0441CEZZ
J Zener Diode, 32V
J Zener Diode, 5.6V
J Diode
AA
AA
AA
J Zener Diode, 11V
J Zener Diode, 5.6V
J Diode
AB
AA
AA
J
J
J
J
Diode
Zener Diode, 13V
Zener Diode, 13V
Diode
AB
AB
AB
AA
J
J
J
J
J
J
J
Diode
Diode
Zener Diode, 9.1V
Zener Diode, 9.1V
Diode
Zener Diode, 27V
Diode
AC
AC
AA
AA
AB
AA
AE
J Diode
AC
J Diode
AC
J Diode
AC
J Diode
AC
J Diode
AA
J Diode
AB
J Diode
AB
J Diode
J Diode
AF
AC
J Zener Diode, 5.6V
J Diode
J Diode
AA
AC
AA
J Diode
AA
J Zener Diode, 5.1V
J Diode
AA
AC
19U-M100,19U-M100S
CU19M10
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
D753
RH-DX0441CEZZ
or
RH-DX0110CEZZ
å D757
RH-DX0048GEZZ
or
VHD1SS119//-1
å D758
RH-DX0131CEZZ
å VA701 RH-VX0019CEZZ
or
RH-VX0035CEZZ
or
RH-VX0048CEZZ
J Diode
AC
J Diode
AA
J Diode
J Varistor
(19U-M100, 19U-M100S)
AC
AC
C212
C220
C301
C302
C304
C305
C306
C354
C356
C357
C358
C361
C401
C411
C412
C414
C416
C418
C421
C451
C454
C455
C456
C509
C510
C512
C513
C514
C515
C516
C517
C520
C530
C531
C606
C607
å C610
PACKAGED CIRCUIT
å
PR702 RMPTP0092CEZZ J Packaged Circuit
X801 RCRSB0001PEZZ R Crystal
or
RCRSB0205CEZZ
AH
AL
FILTER AND COILS
CF2040
L50
L201
L202
L203
L204
L301
å L701
RFiLA0099CEZZ
VP-DF150K0000
VP-XF1R2K0000
VP-XF1R2K0000
VP-XF220K0000
RCiLi0632CEZZ
VP-XF150K0000
RCiLF0078PEZZ
or
RCiLF0069PEZZ
å L702
RCiLF0078PEZZ
or
RCiLF0069PEZZ
å L705
RCiLP0179CEZZ
L706 RCiLP0197CEZZ
L2040 RCiLB0131CEZZ
SF201 RFiLC0441CEZZ
J
J
J
J
J
J
J
R
Ceramic Filter
Peaking 15µH
Peaking 1.2µH
Peaking 1.2µH
Peaking 22µH
IF Coil
Peaking 15µH
Coil
AE
AB
AB
AB
AB
AE
AB
AF
R Coil (CU19M10)
AF
J
J
J
J
AD
AE
AE
AH
Coil
Coil
Oscillation Coil
SAW Filter
å
C612
C633
C634
C635
C636
C637
C652
C653
C661
C662
å C701
TRANSFORMERS
å
T601
'å
å
T602
T702
RTRNZ0731CEZZ J Transformer
or
RTRNZ0026PEZZ
RTRNF0213PEZZ R H-Volt Transformer
RTRNW0009PEZZ R Transformer
or
RTRNW0003PEZZ
C610
AG
AY
AL
CONTROL
R738
RVR-M4588CEZZ+ R 22k(B) 130V Adj.
or
RVR-M4336CEZZ
AC
CAPACITORS
[EL.··· Electrolytic, M-Poly..··· Metalized Polypro Film]
C51
VCEA0A1AW337M+ R 330
10V EL.
C53
VCEA0A1HW105M J 1.0
50V EL.
C54
VCEA0A1HW475M J 4.7
50V EL.
C55
VCEA0A1AW107M J 100
10V EL.
C101 VCEA0A1CW476M J 47
16V EL.
C201 VCKYCY1HF103Z J 0.01 50V Ceramic
C202 VCKYCY1HF103Z J 0.01 50V Ceramic
C203 VCKYCY1HF103Z J 0.01 50V Ceramic
C204 VCQYTA1HM223K J 0.022 50V Mylar
C205 VCKYPA1HB103K J 0.01 50V Ceramic
C206 VCKYCY1HB102K J 1000p 50V Ceramic
C207 VCEA0A1CW476M J 47
16V EL.
C208 VCKYCY1HF103Z J 0.01 50V Ceramic
C209 VCEA0A1HW105M J 1.0
50V EL.
C210 VCEA0A1HW474M J 0.47 50V EL.
C702
C703
å C705
AC
AB
AB
AB
AB
AA
AA
AA
AB
AA
AA
AB
AA
AB
AB
å
31
C706
★
Description
Code
VCEA0A1HW474M
VCKYCY1CB104K
VCCCCY1HH220J
VCKYCY1HB102K
VCCCCY1HH220J
VCKYCY1HB103K
VCQYTA1HM103K
VCEA0A1HW225M
VCKYCY1HB332K
VCEA0A1HW106M
VCEA0A1HW106M
VCEA0A1CW227M
VCCCCY1HH470J
VCEA0A1AW108M
VCKYCY1HB103K
VCEA0A1HW225M
VCEA0A1HW105M
VCKYCY1HB103K
VCEA0A1HW106M
VCQYTA1HM563K
VCEA0A1HW475M
VCEA0A1CW226M
VCEA0A1HW475M
VCKYPA2HB102K
VCEA0A1VW477M
VCFYSA1JB224J+
VCFYSA1JB473J
VCEA0A1EW477M
VCEA0A1HW475M
VCKYCY1HB222K
VCEA0A1CW226M
VCEA0A1HW107M
VCFYFA1HA334J
VCFYFA1HA564J
VCKYPA2HB561K
VCKYPA1HB472K
VCFPVC3ZA772H
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
R
J
J
J
J
J
J
J
J
J
J
J
AB
AB
AA
AA
AA
AA
AB
AB
AA
AB
AB
AC
AA
AC
AA
AB
AB
AA
AB
AB
AB
AB
AB
AA
AB
AD
AC
AD
AB
AA
AB
AB
AB
AB
AA
AA
AD
VCFPVC3ZA802H
J
VCFPVC2DB474J
VCEA0A1AW337M+
VCKYCY1HF103Z
VCEA0A1HW105M
VCQYTA1HM153K
VCEA0A1CW476M
VCEA0A1HW475M
VCEA0A1HW105M
VCKYPA2HB152K
VCEA0A1CW477M
RC-FZ036SCEZZ
or
RC-FZ008SGEZZ
or
RC-FZ029CUMZZ
or
RC-FZ028SCEZZ
or
RC-FZ016SCEZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
RC-EZ1022CEZZ
or
RC-EZ0609CEZZ
or
RC-EZ0629CEZZ
RC-KZ0092GEZZ
or
RC-KZ021SCEZZ
or
RC-KZ009SCEZZ
or
RC-KZ0106GEZZ
or
RC-KZ0156CEZZ
J
R
J
J
J
J
J
J
J
J
J
0.47 50V EL.
0.1
16V Ceramic
22p
50V Ceramic
1000p 50V Ceramic
22p
50V Ceramic
0.01 50V Ceramic
0.01 50V Mylar
2.2
50V EL.
3300p 50V Ceramic
10
50V EL.
10
50V EL.
220
16V EL.
47p
50V Ceramic
1000 10V EL.
0.01 50V Ceramic
2.2
50V EL.
1.0
50V EL.
0.01 50V Ceramic
10
50V EL.
0.056 50V Mylar
4.7
50V EL.
22
16V EL.
4.7
50V EL.
1000p 500V Ceramic
470
35V EL.
0.22 63V Mylar
0.047 63V Mylar
470
25V EL.
4.7
50V EL.
2200p 50V Ceramic
22
16V EL.
100
50V EL.
0.33 50V Mylar
0.56 50V Mylar
560p 500V Ceramic
4700p 50V Ceramic
7700p 1.5kV M-Poly.
(19U-M100)
8000p 1.5kV M-Poly.
(19U-M100S, CU19M10)
0.47 200V M-Poly.
330
10V EL.
0.01 50V Ceramic
1.0
50V EL.
0.015 50V Mylar
47
16V EL.
4.7
50V EL.
1.0
50V EL.
1500p 500V Ceramic
470
16V EL.
0.1
AC250V M-Poly.
(19U-M100, 19U-M100S)
Part No.
J 0.01
J 0.01
J 470
220
AC250V Ceramic
AC250V Ceramic
200V EL.
AD
AE
AC
AA
AB
AA
AB
AB
AB
AA
AC
AC
AC
AC
AK
200V EL.
220
200V EL.
J 0.0033 AC250V Ceramic
AC
19U-M100,19U-M100S
CU19M10
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
å
C708
RC-FZ037SCEZZ
or
RC-FZ012SGEZZ
or
RC-FZ017SCEZZ
or
RC-FZ029SCEZZ
VCKYPA2HB472K
RC-EZ0638CEZZ
RC-EZ0724CEZZ
VCKYPH3DB561K
VCKYPA2HB472K
VCEA0A1CW108M
VCEA0A1EW227M
VCKYPA1HF103Z
VCCCPA1HH680J
VCEA0A1EW226M
RC-KZ0040CEZZ
VCEA0A1HW104M
VCEA0A1EW476M
VCKYPH3DB561K
VCKYPA1HF103Z
VCEA0A1CW476M
VCKYPH3DB561K
J 0.22 275V M-Poly.
(CU19M10)
AD
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AB
AG
AG
AC
AB
AD
AB
AA
AA
AB
AD
AB
AB
AC
AA
AB
AC
C754
C758
C759
C760
C771
C772
C783
C801
C802
C807
C808
C809
C811
C812
C901
C905
C2001
C2002
C2040
C2041
C2060
C2061
C2062
C2201
C2202
C2601
C2602
VCEA0A1CW476M
VCEA0A2EW106M
VCKYPA2HB102K
VCEA0A1CW108M
VCEA0A1CW476M
VCEA0A1CW476M
VCQYTA1HM103K
VCCCCY1HH180J
VCEA0A1CW106M
VCKYCY1EF104Z
VCEA0A1CW106M
VCEA0A1HW105M
VCKYCY1CB473K
VCEA0A1HW474M
VCEA0A1HW105M
VCEA0A1HW106M
VCCCCY1HH101J
VCCCCY1HH101J
VCEA0A1AW107M
VCEA0A1HW105M
VCKYCY1CB104K
VCKYCY1HB222K
VCEA0A1AW107M
VCKYCY1HB682K
VCCCCY1HH560J
VCEA0A1HW475M
VCCCCY1HH101J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
RJ2
RJ4
RJ5
RJ7
RJ8
RJ9
RJ10
RJ12
RJ16
RJ18
RJ19
RJ20
RJ21
RJ28
RJ29
[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
VRS-CY1JF000J
J 0
1/16W M-Ox.
C717
C723
C725
C726
å C727
å C730
å C731
C732
C735
C737
C738
C739
C740
C743
C750
C752
C753
å
å
4700p 500V Ceramic
33
160V EL.
100
160V EL.
560p 2kV Ceramic
4700p 500V Ceramic
1000 16V EL.
220
25V EL.
0.01 50V Ceramic
68p
50V Ceramic
22
25V EL.
820p 2kV Ceramic
0.1
50V EL.
47
25V EL.
560p 2kV Ceramic
0.01 50V Ceramic
47
16V EL.
560p 2kV Ceramic
(19U-M100, 19U-M100S)
47
16V EL.
10
250V EL.
1000p 500V Ceramic
1000 16V EL.
47
16V EL.
47
16V EL.
0.01 50V Mylar
18p
50V Ceramic
10
16V EL.
0.1
25V Ceramic
10
16V EL.
1.0
50V EL.
0.047 16V Ceramic
0.47 50V EL.
1.0
50V EL.
10
50V EL.
100p 50V Ceramic
100p 50V Ceramic
100
10V EL.
1.0
50V EL.
0.1
16V Ceramic
2200p 50V Ceramic
100
10V EL.
6800p 50V Ceramic
56p
50V Ceramic
4.7
50V EL.
100p 50V Ceramic
R53
R54
R55
R56
R57
R101
R201
R202
R203
R204
R205
R206
R207
R208
R209
R210
R211
R212
R215
R220
R301
R302
R353
R354
R355
R357
R401
R402
R403
R404
R411
R412
R413
R414
R421
å R451
R453
R454
R455
R456
R457
R458
R460
R461
R462
R495
R512
R513
R514
R515
R516
R517
R518
R519
R520
å
AB
AD
AA
AD
AB
AB
AB
AA
AB
AA
AB
AB
AA
AB
AB
AB
AA
AA
AB
AB
AB
AA
AB
AA
AA
AB
AA
RESISTORS
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
VRS-VV3LB223J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF823J
VRD-RA2BE563J
VRD-RA2BE152J
VRS-CY1JF221J
VRS-CY1JF122J
VRS-CY1JF682J
VRS-CY1JF270J
VRD-RA2BE680J
VRD-RA2EE151J
VRD-RA2BE223J
VRS-CY1JF332J
VRS-CY1JF000J
VRS-CY1JF104J
VRS-CY1JF104J
VRS-CY1JF000J
VRS-CY1JF000J
VRS-CY1JF331J
VRS-CY1JF102J
VRS-CY1JF152J
VRD-RA2BE683J
VRS-CY1JF103J
VRD-RA2BE223J
VRS-CY1JF822J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-RA2BE102J
VRS-CY1JF684J
VRS-CY1JF391J
VRS-CY1JF102J
VRS-CY1JF000J
VRS-CY1JF223J
VRS-SV2HC103J
VRD-RA2BE152J
VRD-RA2EE334J
VRD-RA2BE392J
VRS-CY1JF103J
VRD-RA2BE102J
VRD-RA2EE334J
VRD-RA2BE152J
VRS-CY1JF184J
VRS-CY1JF273J
VRS-VV3DB820J
VRD-RM2HD102J
VRD-RM2HD102J
VRD-RM2HD1R0J
VRS-VV3AB391J
VRS-CY1JF153J
VRS-CY1JF102J
VRS-CY1JF333J
VRS-CY1JF103J
VRD-RM2HD1R2J
★
Description
Code
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
22k 3W
M-Ox.
100 1/16W M-Ox.
100 1/16W M-Ox.
82k 1/16W M-Ox.
56k 1/8W
Carbon
1.5k 1/8W
Carbon
220 1/16W M-Ox.
1.2k 1/16W M-Ox.
6.8k 1/16W M-Ox.
27 1/16W M-Ox.
68 1/8W
Carbon
150 1/4W
Carbon
22k 1/8W
Carbon
3.3k 1/16W M-Ox.
0
1/16W M-Ox.
100k 1/16W M-Ox.
100k 1/16W M-Ox.
0
1/16W M-Ox.
0
1/16W M-Ox.
330 1/16W M-Ox.
1.0k 1/16W M-Ox.
1.5k 1/16W M-Ox.
68k 1/8W
Carbon
10k 1/16W M-Ox.
22k 1/8W
Carbon
8.2k 1/16W M-Ox.
100 1/16W M-Ox.
100 1/16W M-Ox.
100 1/16W M-Ox.
1.0k 1/8W
Carbon
680k 1/16W M-Ox.
390 1/16W M-Ox.
1.0k 1/16W M-Ox.
0
1/16W M-Ox.
22k 1/16W M-Ox.
10k 1/2W
M-Ox.
1.5k 1/8W
Carbon
330k 1/4W
Carbon
3.9k 1/8W
Carbon
10k 1/16W M-Ox.
1.0k 1/8W
Carbon
330k 1/4W
Carbon
1.5k 1/8W
Carbon
180k 1/16W M-Ox.
27k 1/16W M-Ox.
82 2W
M-Ox.
1.0k 1/2W
Carbon
1.0k 1/2W
Carbon
1.0 1/2W
Carbon
390 1W
M-Ox.
15k 1/16W M-Ox.
1.0k 1/16W M-Ox.
33k 1/16W M-Ox.
10k 1/16W M-Ox.
1.2 1/2W
Carbon
(19U-M100S, CU19M10)
1.5 1/2W
Carbon
(19U-M100)
1.0k 1/8W
Carbon
5.6k 1/8W
Carbon
2.7k 1/8W
Carbon
22k 1/8W
Carbon
(19U-M100)
2.7k 1/8W
Carbon
4.7k 1/8W
Carbon
6.8k 2W
M-Ox.
120 1/8W
Carbon
1.0k 1/8W
Carbon
6.8k 2W
M-Ox.
390 2W
M-Ox.
5.6k 1W
M-Ox.
22 1/2W
Carbon
3.3 5W
M-Ox.
2.2k 1/16W M-Ox.
10k 1/16W M-Ox.
4.7k 1/8W
M-Film
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
R520
VRD-RM2HD1R5J J
R522
R523
R525
R527
VRD-RA2BE102J
VRD-RA2BE562J
VRD-RA2BE272J
VRD-RA2BE223J
J
J
J
J
VRD-RA2BE272J
VRD-RA2BE472J
VRS-VV3DB682J
VRD-RA2BE121J
VRD-RA2BE102J
VRS-VV3DB682J
VRS-VV3DB391J
VRS-VV3AB562J
VRD-RM2HD220J
VRS-KA3HG3R3K
VRS-CY1JF222J
VRS-CY1JF103J
VRN-RA2BK472F
J
J
J
J
J
J
J
J
J
J
J
J
J
R528
R529
å R604
R605
R606
å R607
å R608
å R609
R610
å R611
R622
R623
R624
32
Part No.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AA
AA
AA
19U-M100,19U-M100S
CU19M10
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
R634
R635
R636
å R641
å R651
å R653
å R654
å R655
å R659
VRD-RM2HD121J
VRS-CY1JF332J
VRD-RA2EE221J
VRS-VV3AB682J
VRD-RM2HD270J
VRS-CY1JF000J
VRD-RA2BE154J
VRS-CY1JF103J
VRN-VV3AB2R2J
J
J
J
J
J
J
J
J
J
å
R659
VRN-VV3ABR82J
J
å
å
å
R661
R662
R702
VRN-VV3ABR47J
VRD-RA2BE102G
RR-DZ0049CEZZ
or
RR-HZ0048CEZZ
or
VRD-UB2HG395K
VRW-KP3HC1R8K
VRN-VV3ABR39J
VRN-VV3ABR39J
VRD-RM2HD270J
VRS-CY1JF102J
VRS-SV2HC102J
VRS-CY1JF334J
VRD-RA2BE100J
VRS-SV2HC122J
VRD-RA2BE150J
VRS-VV3AB121J
VRD-RM2HD124J
VRS-CY1JF225J
VRS-CY1JF000J
VRS-SV2HC821J
VRD-RA2EE394J
VRD-RM2HD184J
VRD-RM2HD332J
VRD-RM2HD470J
VRN-RA2BK682F
VRD-RM2HD561J
VRD-RM2HD681J
VRD-RA2BE821J
VRD-RA2BE562J
VRD-RM2HD151J
VRS-SV2HC100J
VRS-VV3LB270J
VRS-VV3LB680J
VRD-RM2HD470J
VRS-CY1JF272J
VRS-CY1JF272J
VRS-CY1JF223J
VRS-CY1JF223J
VRD-RA2BE101J
VRS-CY1JF750J
VRS-CY1JF102J
VRS-CY1JF104J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF472J
VRS-CY1JF102J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF223J
VRS-CY1JF103J
VRS-CY1JF223J
VRS-CY1JF333J
VRD-RA2BE223J
R703
R705
R706
R707
R708
R710
R711
R712
R713
R715
R716
å R721
R722
R723
R725
R733
R736
R739
R740
R741
R742
R743
R751
R752
R755
å R758
å R773
å R774
R801
R807
R808
R809
R810
R901
R902
R906
R925
R961
R962
R2001
R2002
R2006
R2008
R2009
R2010
R2012
R2016
R2018
R2020
R2022
R2023
å
AA
AA
AA
AA
AA
AA
AA
AA
AA
J
J
J
120 1/2W
Carbon
3.3k 1/16W M-Ox.
220 1/4W
Carbon
6.8k 1W
M-Ox.
27 1/2W
Carbon
0
1/16W M-Ox.
150k 1/8W
Carbon
10k 1/16W M-Ox.
2.2 1W
M-Film
(19U-M100)
0.82 1W
M-Film
(19U-M100S, CU19M10)
0.47 1W
M-Film
1.0k 1/8W
Carbon
3.9M 1/2W
Carbon
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
1.8 5W
0.39 1W
0.39 1W
27 1/2W
1.0k 1/16W
1.0k 1/2W
330k 1/16W
10 1/8W
1.2k 1/2W
15 1/8W
120 1W
120k 1/2W
2.2M 1/16W
0
1/16W
820 1/2W
390k 1/4W
180k 1/2W
3.3k 1/2W
47 1/2W
6.8k 1/8W
560 1/2W
680 1/2W
820 1/8W
5.6k 1/8W
150 1/2W
10 1/2W
27 3W
68 3W
47 1/2W
2.7k 1/16W
2.7k 1/16W
22k 1/16W
22k 1/16W
100 1/8W
75 1/16W
1.0k 1/16W
100k 1/16W
100 1/16W
100 1/16W
1.0k 1/16W
10k 1/16W
10k 1/16W
4.7k 1/16W
1.0k 1/16W
1.0k 1/16W
10k 1/16W
22k 1/16W
10k 1/16W
22k 1/16W
33k 1/16W
22k 1/8W
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
Cement
M-Film
M-Film
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
Carbon
Carbon
M-Film
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
R2024
R2025
R2026
R2027
R2028
R2029
R2032
R2033
R2034
R2040
R2041
R2042
R2043
R2044
R2045
R2047
R2048
R2049
R2060
R2061
R2062
R2063
R2065
R2066
R2067
R2068
R2070
R2072
R2101
R2102
R2201
R2202
R2203
R2211
R2212
R2213
R2401
R2402
R2403
R2404
R2501
R2503
R2504
R2505
R2506
R2507
R2508
R2509
R2601
AA
AA
AB
AB
★
Part No.
VRD-RA2BE682J
VRD-RA2BE682J
VRD-RA2BE682J
VRD-RA2BE682J
VRS-CY1JF102J
VRS-CY1JF103J
VRD-RA2BE471J
VRS-CY1JF684J
VRS-CY1JF684J
VRS-CY1JF102J
VRS-CY1JF333J
VRD-RA2BE101J
VRD-RA2BE101J
VRS-CY1JF683J
VRS-CY1JF101J
VRS-CY1JF221J
VRS-CY1JF562J
VRS-CY1JF333J
VRS-CY1JF221J
VRS-CY1JF562J
VRS-CY1JF183J
VRS-CY1JF222J
VRS-CY1JF000J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF103J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-RA2BE103J
VRD-RA2BE473J
VRS-CY1JF332J
VRD-RA2BE222J
VRS-CY1JF682J
VRD-RA2BE223J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF123J
VRS-CY1JF273J
VRS-CY1JF123J
VRS-CY1JF563J
VRS-CY1JF563J
VRS-CY1JF823J
VRS-CY1JF153J
VRS-CY1JF272J
VRD-RA2BE331J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
6.8k
6.8k
6.8k
6.8k
1.0k
10k
470
680k
680k
1.0k
33k
100
100
68k
100
220
5.6k
33k
220
5.6k
18k
2.2k
0
10k
10k
10k
10k
10k
100
100
10k
47k
3.3k
2.2k
6.8k
22k
100
100
100
100
12k
27k
12k
56k
56k
82k
15k
2.7k
330
1/8W
1/8W
1/8W
1/8W
1/16W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
1/8W
1/16W
1/8W
1/16W
1/8W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/8W
Carbon
Carbon
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
M-Ox.
Carbon
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Carbon
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
SWITCHES
S2501 QSW-K0003AJZZ
or
QSW-K0079GEZZ
S2502 QSW-K0003AJZZ
or
QSW-K0079GEZZ
S2503 QSW-K0003AJZZ
or
QSW-K0079GEZZ
S2504 QSW-K0003AJZZ
or
QSW-K0079GEZZ
S2505 QSW-K0003AJZZ
or
QSW-K0079GEZZ
J POWER
AB
J VOL-Down
AB
J VOL-Up
AB
J CH-Down
AB
J CH-Up
AB
MISCELLANEOUS PARTS
å
å
33
RY701 RRLYJ0081CEZZ
F701 QFS-B4023CEZZ
or
QFS-B4021GEZZ
FH701 QFSHD1013CEZZ
FH702 QFSHD1014CEZZ
J Relay
J Fuse, 4A/125V
AL
AC
J Fuse Holder
J Fuse Holder
AC
AC
19U-M100,19U-M100S
CU19M10
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
FB351 RBLN-0091GEZZ
or
RBLN-0047CEZZ
FB601 RBLN-0047CEZZ
FB2002RBLN-0091GEZZ
or
RBLN-0037CEZZ
J951 QJAKF0041CEZZ
P302 QPLGN0261CEZZ
P401 QPLGN0561CEZZ
P601 QPLGN0660CEZZ
P651 QPLGN0361CEZZ
P701 QPLGN0260CEZZ
P751 QPLGN0461CEZZ
P2001 QPLGN0561CEZZ
RMC2601 RRMCU0232CEZZ
or
RRMCU0252CEZZ
JA409 RBLN-0047CEZZ
RDA501 PRDAR0297PEFW
RDA602 PRDAR0216PEFW
RDA701 PRDAR0026PEFW
LX-BZ3100CEFD
J Ferrite Bead
★
Part No.
Description
Code
PWB-B:DUNTKA359WEV2(19U-M100)
PWB-B:DUNTKA359WEV1(19U-M100S,
CU19M10)
CRT UNIT
TRANSISTORS
AB
Q852
J Ferrite Bead
J Ferrite Bead
AB
AB
J
J
J
J
J
J
J
J
J
Jack, A/V-In
Plug, 2-pin(S)
Plug, 5-pin(GBN)
Plug, 6-pin(K)
Plug, 3-pin(TP651-3)
Plug, 2-pin(M)
Plug, 4-pin(YBN)
Plug, 5-pin(TP2001-5)
R/C Receiver
AH
AB
AB
AC
AB
AC
AB
AB
AG
Q856
J
R
R
R
J
Ferrite Bead
Heat Sink, for IC501
Heat Sink, for Q602
Heat Sink, for Q701
Screw
AB
AD
AE
AD
AA
D885
Q854
Q881
RH-TX0110BMZZ+
or
VS2SC2229O/1E
RH-TX0110BMZZ+
or
VS2SC2229O/1E
RH-TX0110BMZZ+
or
VS2SC2229O/1E
VS2SA1266-Y-1
or
VS2SA1015-Y-1
R TX0110BM
AC
R TX0110BM
AC
R TX0110BM
AC
J 2SA1266-Y
AA
DIODES
D882
RH-DX0048GEZZ
or
RH-DX0475CEZZ
RH-DX0475CEZZ
or
RH-DX0048GEZZ
J Diode
AA
J Diode
AB
COIL
L852
VP-MK820K0000
J Peaking 82µH
AB
CAPACITORS
C851
C852
C853
C854
C883
[EL.··· Electrolytic]
VCCCCY1HH151J J 150p 50V
VCCCCY1HH151J J 150p 50V
VCCSPA1HL151J J 150p 50V
RC-KZ0029CEZZ J 0.01 250V
or
RC-KZ0160GEZZ
VCEA0A1CW336M J 33
16V
Ceramic
Ceramic
Ceramic
Ceramic
AA
AA
AA
AC
EL.
AB
RESISTORS
R851
R852
R853
å R857
R858
R859
R860
R861
å R865
R866
R867
R868
R869
å R873
R874
R881
R882
R883
R884
R886
R887
R890
R891
[M-Ox.··· Metal Oxide]
VRS-CY1JF470J
J 47 1/16W M-Ox.
(19U-M100S/CU19M10)
VRD-RA2BE181J J 180 1/8W
Carbon
VRS-CY1JF121J
J 120 1/16W M-Ox.
VRS-VV3AB123J
J 12k 1W
M-Ox.
VRD-RM2HD332J J 3.3k 1/2W
Carbon
VRS-CY1JF470J
J 47 1/16W M-Ox.
(19U-M100S/CU19M10)
VRD-RA2BE181J J 180 1/8W
Carbon
VRS-CY1JF121J
J 120 1/16W M-Ox.
VRS-VV3AB123J
J 12k 1W
M-Ox.
VRD-RM2HD332J J 3.3k 1/2W
Carbon
VRS-CY1JF470J
J 47 1/16W M-Ox.
VRS-CY1JF181J
J 180 1/16W M-Ox.
VRS-CY1JF121J
J 120 1/16W M-Ox.
VRS-VV3AB123J
J 12k 1W
M-Ox.
VRD-RM2HD332J J 3.3k 1/2W
Carbon
VRS-CY1JF561J
J 560 1/16W M-Ox.
VRS-CY1JF391J
J 390 1/16W M-Ox.
VRD-RA2BE561J J 560 1/8W
Carbon
VRS-CY1JF152J
J 1.5k 1/16W M-Ox.
VRS-CY1JF821J
J 820 1/16W M-Ox.
VRD-RA2BE470J J 47 1/8W
Carbon
VRS-CY1JF470J
J 47 1/16W M-Ox.
(19U-M100)
VRS-CY1JF470J
J 47 1/16W M-Ox.
(19U-M100)
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
P851
P852
34
QPLGN0561CEZZ J Plug, 5-pin(GBN)
QPLGN0461CEZZ J Plug, 4-pin(YBN)
AB
AB
19U-M100,19U-M100S
CU19M10
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-B:DUNTKA359WEV2(19U-M100)
PWB-B:DUNTKA359WEV1(19U-M100S,
CU19M10)
CRT UNIT (Continued)
SC851 QSOCV0016PEZZ R CRT Socket
or
(19U-M100S/CU19M10)
QSOCV0933CEZZ
SC852 QSOCV0841CEZZ J CRT Socket (19U-M100)
or
QSOCV0840CEZZ
ACC701 QACCD3064CESA J
SP1
VSP0080PBQ9YA R
or
VSP0080PBP8YA
or
VSP0080PBQ3YA
QCNW-0167MEZZ J
QCNW-2046PEZZ R
QCNW-2160PEZZ R
LHLDK0014PEZZ R
LHLDZ0063PEZZ R
TLABM1829PEZZ R
TLABM1906PEZZ
TLABN0001PEZZ
LX-TZ0006PEFD
LX-WZ0003PEFD
PSPAG0001PE00
XTASD30P12000
XTASD40P20000
LX-TZ3004CEFD
TCAUH0008PEZZ
R
R
R
R
R
J
J
TCAUS0004PEZZ
TCAUS0013PEZZ
J
J
J
AC Cord (AC120V/60Hz)
Speaker, 32 ohm
Connecting Cord
Connecting Cord
Connecting Cord
AC Cord Holder
Anode Clamp Holder
Model Label
(19U-M100/100S)
Model Label(CU19M10)
Serial No. Label
CRT Screw, x4
CRT Washer, x4
CRT Spacer, x4
Screw, x1
Screw, x4
Screw
Caution Card
(19U-M100/100S)
Warning Label(CU19M10)
Attention Label(CU19M10)
★
Description
Code
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKC6801PEZZ
AF
SPAKC6802PEZZ
SPAKP0098PEZZ
SPAKX2701PEZZ
SSAKA0001PEZZ
AG
MISCELLANEOUS PARTS
å
Part No.
– Packing Case
(19U-M100/100S)
– Packing Case(CU19M10)
– Wrapping Paper
– Buffer Material
– Polyethylene Bag
—
—
—
—
—
SUPPLIED ACCESSORIES
AM
AH
RRMCG1324CESA R Infrared R/C Unit
TGAN-0018PEZZ R Guarantee Card
(19U-M100/100S)
TiNS-7643PEZZ
R Operation Manual
(19U-M100/100S)
TiNS-7644PEZZ
R Operation Manual
(CU19M10)
AE
AF
AG
AD
AD
AB
AD
AD
AB
AB
AA
AA
AA
AB
AD
AB
35
AT
AD
AE
AN
19U-M100,19U-M100S
CU19M10
Ref. No.
Part No.
★
Description
Code
Ref. No.
CABINET PARTS
1
1
1-1
1-2
1-3
2
★
Part No.
Code
CABINET PARTS LOCATION
CCABA2713WEV0 R Front Cabinet Ass’y
BA
(19U-M100/100S)
CCABA2713WEV1 R Front Cabinet Ass’y
BA
(CU19M10)
Not Available
– Front Cabinet
—
GCOVA0069PEKA J LED Cover
AD
JBTN-0243PESB R Button(Power, VOL-Up/Down, AE
CH-Up/Down)
GCABB2477PEKA R Rear Cabinet
Description
1 1-1
2
AX
POWE
R
– VOL
+
CH
MENU
1-2
36
1-3
19U-M100,19U-M100S
CU19M10
PACKING OF THE SET
★ Polyethylene Bag
Operation Manual
Guarantee Card
(19U-M100/100S)
★ Batteries
★ Polyethylene Mat
Infrared R/C unit
★Buffer Material
FRONT
★ Packing Case
REAR
★ MARK : Not replacement items.
37
Use 22 staples to
fix the bottom side
of packing case.
19U-M100,19U-M100S
CU19M10
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
D SEM P SREC TQ1282-S
Mar. 2002 Printed in Japan
MI. KG
38
Download PDF