INDUSTRIAL COMMUNICATION SOLUTIONS FOR ENCOMPASS™

INDUSTRIAL COMMUNICATION SOLUTIONS FOR ENCOMPASS™
INDUSTRIAL
COMMUNICATION SOLUTIONS
FOR ENCOMPASS™
All trademarks used herein are the
property of their respective owners.
Reference to any non-Molex trademarks
is not intended to claim any endorsement
or association between Molex and the
respective trademark owners, and should
not be construed.
Table of Contents
Industrial Communication Solutions for Rockwell
Automation’s Encompass Program.........................................................................3
Brad® SSTtm Communication Module for Rockwell ControlLogix
Modbus/TCP/Siemens Industrial Ethernet and Modbus Serial Protocols..................4
Modbus Serial.......................................................................................................6
PROFIBUS-DP Master and Slave..........................................................................8
PROFIBUS-DP Slave Only...................................................................................10
AS-Interface Scanner...........................................................................................12
Brad® SSTtm Communication Module for Rockwell CompactLogix
Modbus/TCP and and Modbus Serial Protocols Standard Version Plus Version......14
Brad® SSTtm Communication Module for Rockwell CompactLogix
and MicroLogix 1500
AS-Interface Scanner...........................................................................................17
Brad® SSTtm Communication Module for Rockwell SLC500
PROFIBUS-DP Master and Slave........................................................................18
AS-Interface Scanner...........................................................................................19
Brad® SSTtm PROFIBUS Remote Module
PROFIBUS-DP Master and Slave........................................................................20
Brad® SSTtm IP67 PROFIBUS Remote Module
PROFIBUS-DP Master and Slave........................................................................22
Brad® SSTtm DeviceNet Remote Scanner
DeviceNet* Control over EtherNet........................................................................24
Brad® applicom® Network Interface Card
Industrial Ethernet...............................................................................................26
PROFIBUS for Scada/HMI..................................................................................29
Brad® applicomIO® Network Interface Card
Ethernet Fieldbus.................................................................................................33
Brad® Software Development Kits EtherNet/IP Scanner and Adapter
Ethernet Software Development Kits.....................................................................34
Brad® Software Development Kits CIP Safety DeviceNet* Slave and EtherNet/IP Adapter
DeviceNet Software Development Kits..................................................................36
Brad® Direct-Link® Windows Compatible Protocol Drivers
Serial and Ethernet TCP/IP.................................................................................39
Brad® DeviceNet Diagnostic Tools
eNetMetertm and DN NetAlytixtm...........................................................................40
NetMeter®...........................................................................................................41
DeviceNet Brad® Mini-Change® Diagnostic Power Monitor® Tees
Male/Female Thick Media....................................................................................43
*DeviceNet is a registered trademark of Open DeviceNet Vendor Association
1
About Molex
Our long history of innovation has created value for the Molex and Rockwell
Automation partnership and their customers. Molex has over 30 Brad®
communication products in the Encompass Program, including network interface
cards, PLC/PAC communication modules, diagnostics and unique remote scanners.
The people at Molex take pride in creating innovative products that allow customers
to solve difficult applications.
The Molex partnership with Rockwell Automation began with smaller companies
called SST™ and applicom® that began operation in the early 1990s. By 2000 both
of these organizations had been acquired by Woodhead® who in turn was acquired
by Molex in 2006. Despite the evolution in ownership, one thing has remained
constant throughout the years; focus on the creation of market-leading industrial
communication solutions.
Global Service
Molex has a significant Sales and Customer Service presence in all global markets.
In addition, several Technical Support locations in North America, Europe and Asia
mean that customers can receive timely answers to their questions or issues.
Industries we serve:
• Automotive
• Oil and gas
• Water and wastewater
• Consumer and packaged goods
• Mining, minerals and cement
• Metals
• Semi-conductors
2
Empowering the Communication Interface
As part of the family of Brad® communication solutions, our products bring together
years of experience working with innovating and developing solutions for industrial
networks and fieldbuses. Globally recognized product lines applicom®, SST™ and
Direct-Link™ are the powerhouses of the Brad communication portfolio, enabling
hundreds of thousands of automation systems to communicate and gather valuable
information through communications software, network interfaces, Ethernet
switches, remote scanners and diagnostic tools.
Diagnostic Tools
eNetMeter™
Continuously monitors a DeviceNet* network and sends the information over
EtherNet/IP to a PLC or PC monitoring system. The information can be read
directly by an EtherNet/IP master. Optionally, data can be accessed through
Brad communications NetAlytix™ software, a DLL interface or an OPC server.
NetMeter®
Hand-held device which connects to DeviceNet as required. AutoSearch mode makes
this easy to use for the novice, while Expert mode allows closer examination of some
677 key DeviceNet measurements as compared to the DeviceNet specification.
Power-Monitor®
Monitor DeviceNet power quality at any cable junction.
Software Development Kits
EtherNet/IP Stacks
EtherNet/IP source code stacks are the most open, powerful and cost-effective
solutions for manufacturers who want to embed EtherNet/IP protocol into industrial
controllers and field devices.
CIP Safety Stacks
CIP Safety Stack software solution allows industrial-device manufacturers
embedding CIP Safety technology quickly and economically within their products.
Remote Scanners
DeviceNet Remote Scanner
Control I/O devices connected to DeviceNet without the need of a local PC. Remote
DeviceNet Scanners can be connected back to a PC residing on an Ethernet network
through an Ethernet switch.
PROFIBUS Remote Scanner
Connect PROFIBUS I/O devices to RA Logix processors using EtherNetI/P. Easy to
integrate within a Logix system using both RSLogix5000 and the SST PROFIBUS
Console software.
Network Interfaces
PC Interfaces
Connect PC-Based Control, HMI / Operator Interface, or SCADA applications
to an industrial network including Data Highway Plus, DeviceNet, PROFIBUS,
EtherNetI/P, Serial, and Ethernet TCP/IP (Siemens , Schneider, Omron, Mitsubishi).
PLC Communication Modules
Connect an Allen-Bradley CompactLogix, ControlLogix or SLC 500 to industrial
networks including AS-Interface, Modbus TCP, Siemens Industrial Ethernet S5/S7,
Modbus Serial and PROFIBUS.
Software Drivers
Software drivers provide data acquisition between Windows PC-Based applications
and industrial devices connected to Ethernet TCP/IP and Serial networks.
*DeviceNet is a trademark of Open DeviceNet Vendor Association (ODVA)
3
Industrial Communication
Solutions for Rockwell
Automation’s Encompass
Program
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112073 Modbus/TCP, Siemens
Industrial Ethernet and
Modbus Serial Protocols
• Connects your Allen-Bradley ControlLogix to a Modbus/Siemens
Ethernet or Modbus Serial network
• Direct I/O mapping, no ladder logic
to write for configuration and data
transfer between module and CLX processor
• Paging access (AOI provided), with up
to 32K words shared for Input, Output
and Status data
• Industry leading performance, I/O
data refresh every PLC cycle
• Fully integrated into the Rockwell
Automation environment
- Remote configuration and
monitoring via Rockwell RSLinx™
- Add-On-Profile for Rockwell
RSLogix5000
• User-friendly configuration tool with
intuitive graphical interface
• Siemens S7 (S7-1200, S7-200, S7-300, and S7-400) Client and
Server modes
• Siemens S5 Client and Server modes
SPECIFICATIONS
SST-ESR2-CLX-RLL
SST-ESR2-CLXT-RLL eXTreme module
Description
•R
LL support: Remote configuration
and monitoring via RSLinx
• Add-On-Profile for Rockwell®
RSLogix5000
• USB port for user configuration and
firmware upgrade
• Engineering console simplifies user
configuration and diagnostic
• Supports multiple modules in a chassis
• Supports local and remote chassis
• Easy diagnostics:
Built-in LEDs and 4 character display
SST-ESR2-CLXT-RLL eXTreme:
• Same specifications as SST-ESR2CLX-RLL plus:
• Conformal coating
• eXTreme components
• Ambient operating temperature:
-25 to 70° C
Included Hardware/Software
• 128 MB of onboard memory
• 8 MB of flash memory
(user configuration data and firmware)
• CPU data exchange:
- 496 Input bytes + 496 Output bytes
- 32,000 Word Registers via AOI
• USB port:
- Type A
- USB 2 and 1.1 compatible
• Communication:
- 1x Ethernet, 10/100 Mbps, RJ45
- 2x Serial, 110 bps to 115.2 kbps,
RS232/RS485/RS422, RJ45 (DB9
male supplied cable)
• OS supported: Windows XP,
7 (64-bit), Vista, 8 (32, 64-bit)
Compatible Protocols
• Modbus Master (RTU or ASCII)
• Modbus Slave (RTU or ASCII)
• Modbus TCP and UDP Client and
Server
• Siemens S7 and S5 Client and Server
Conformance
• RoHS compliant
• CE
• cULus listed
• Class I Div 2, Groups A,B,C,D
• Marine (RINA)
• Korea CC
• Ex (ATEX)
Cyclic Function Screen Showing Data
Overlapping Errors, Data mapping, Table
Areas, Message Details
4
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
112073-0001
SST-ESR2-CLX-RLL
SST™ 1x Ethernet + 2x Serial ports
communication module for Rockwell
ControlLogix, includes
Remote Link Library
112073-0003
112073-0002
SST-ESR2-CLX-RLL-CC
SST™ 1x Ethernet + 2x Serial ports
communication module for Rockwell
ControlLogix, includes Remote Link
Library, conformal coated
SST-ESR2-CLXT-RLL
SST™ 1x Ethernet + 2x Serial ports
communication module for Rockwell
ControlLogix CLXT (eXTreme), includes
Remote Link Library, conformal coated,
eXTreme module components
Conformal coating material is applied to electronic circuitry to act as protection against moisture, dust,
chemicals, and temperature extremes.
TYPICAL APPLICATION
5
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112073 Modbus/TCP, Siemens
Industrial Ethernet and
Modbus Serial
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112078 Modbus Serial
• Connects your Allen-Bradley
ControlLogix to a Modbus Serial
network
• Direct I/O mapping, no ladder logic
to write for configuration and data
transfer between module and CLX
processor
• Industry leading perfromance,
I/O data refresh every PLC cycle
• Fully integrated into the Rockwell
Automation environment
• User-friendly configuration tool with
intuitive graphical interface
• 4x RS232/RS485 Serial Modbus
channels in a single slot
• Paging access (AOI provided), with up
to 32K words shared for Input, Output
and Status data
SPECIFICATIONS
SST-SR4-CLX-RLL
SST-SR4-CLXT-RLL eXTreme module
Description
•R
LL support: Remote configuration
and monitoring via RSLinx
• Add-On-Profile for Rockwell
RSLogix5000
• USB port for user configuration
and firmware upgrade
• Engineering console simplifies user
configuration and diagnostic
• Supports multiple modules in a chassis
• Supports local and remote chassis
• Easy diagnostics:
Built-in LEDs and 4 characters display
SST-SR4-CLXT-RLL eXTreme:
•S
ame specifications as
SST-SR4-CLX-RLL plus:
• Conformal coating
• eXTreme components
•A
mbient operating temperature:
-25 to 70° C
Cyclic Function Screen Showing Data
Overlapping Errors, Data mapping, Table
Areas, Message Details
6
Included Hardware/Software
• 128 MB of onboard memory
• 8 MB of flash memory
(user configuration data and firmware)
• CPU data exchange:
- 496 Input bytes + 496 Output bytes
- 32,000 Word Registers via AOI
• USB port:
- Type A
- USB 2 and 1.1 compatible
• Communication ports:
- 4x Serial, 110 bps to 115.2 kbps,
RS232/RS485/RS422, RJ45 (DB9
male supplied cable)
• OS supported: Windows XP, 7 (32, 64-bit), Vista, 8 (32, 64-bit)
Compatible Protocols
• Modbus Master (RTU or ASCII)
• Modbus Slave (RTU or ASCII)
Conformance
• RoHS compliant
• CE
• Marine (RINA)
• Korea CC
• cULus listed
• Class I Div 2, Groups A,B,C,D
• Ex (ATEX)
ORDERING INFORMATION
Order No.
Engineering No.
Description
112078-0001
SST-SR4-CLX-RLL
SST™ 4x Serial ports communication
module for Rockwell ControlLogix, includes
Remote Link Library
112078-0002
SST-SR4-CLX-RLL-CC
SST™ 4x Serial ports communication
module for Rockwell ControlLogix, includes
Remote Link Library, conformal coated
112078-0003
SST-SR4-CLXT-RLL
SST™ 4x Serial ports communication module
for Rockwell ControlLogix CLXT (eXTreme),
includes Remote Link Library, conformal
coated, eXTreme module components
Conformal coating material is applied to electronic circuitry to act as protection against moisture, dust,
chemicals, and temperature extremes.
TYPICAL APPLICATION
7
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112078 Modbus Serial
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112016PROFIBUS-DP
Master and Slave
• Connects your Allen-Bradley
ControlLogix to a PROFIBUS network
• Fully integrated into the Rockwell Automation environment
-R
emote configuration and monitoring
via Rockwell RSLinx™
- Add-On-Profile for Rockwell
RSLogix5000
• Direct I/O mapping, no ladder logic
to write for configuration and data
transfer between module and CLX processor
• Conformal coating version:
-P
rovides environmental and
mechanical protection to significantly
extend the life of the components
and circuitry
- Protects electronic boards from
moisture and contaminants
• Typical applications:
- Marine
- Agro-Food
- Mining
- Harsh automotive, etc.
SPECIFICATIONS
SST-PB3-CLX-RLL
SST-PB3-CLXT-RLL eXTreme module
Description
• High-speed deterministic communication
• Easy diagnostics:
Built-in LEDs and 4 characters display
• Manage DP Master and Slave modes
simultaneously
• Allows changes to PROFIBUS
configuration with PLC in RUN mode
• Dynamically add/remove
PROFIBUS slaves from the scan list
• CommDTM driver for FDT Frame
e ngineering software (PACTware™,
FieldCare™, FieldMate™, etc)
•A
uto-Boot (configuration stored in flash)
• Engineering Tools:
- Configuration console
- Test and diagnostic tools
Included Hardware/Software
•A
dd-On-Profile for increased
functionality and reduced commissioning
time
• Support multiple modules in a chassis;
support Local and Remote chassis
• One PROFIBUS port, DB9 female,
galvanic insulation 1000V
• Speed: 9.6 Kbps up to 12 Mbps
• LEDs for system, communication,
and network status
• Up to 1984 input bytes and
1968 output bytes
• One Serial port for configuration
and diagnostic
• Firmware upgradeable
• OS supported: Windows XP, 7 (32, 64-bit), Vista, 8 (32, 64-bit)
8
Compatible Protocols
• Master DP-V0 Class-1 and Class-2
• Master DP-V1 Class-1 and Class-2
• Slave DP-V0
Conformance
• RoHS compliant
• CE
• cULus listed
• Class 1 Div 2, Groups A, B, C, and D
• FDT certified
• Marine (RINA)
• Ex (ATEX)
• Korea CC
SST-PB3-CLXT-RLL eXTreme:
• Same specifications as
SST-PB3-CLX-RLL plus:
• Conformal coating
• eXTreme components
• Ambient operating temperature:
-25 to 70°C
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
112016-0018
SST-PB3-CLX-RLL
SST™ PROFIBUS Master and Slave
communication module for Rockwell
ControlLogix, includes Remote Link Library
112016-0023
SST-PB3-CLX-RLL-CC
SST™ PROFIBUS Master and Slave
communication module for Rockwell
ControlLogix, includes Remote Link Library,
conformal coated
SST-PB3-CLXT-RLL
SST™ PROFIBUS Master and Slave
communication module for Rockwell
ControlLogix CLXT (eXTreme), includes Remote
Link Library, conformal coated, eXTreme
module components
112016-0024
Conformal coating material is applied to electronic circuitry to act as protection against moisture dust,
chemicals, and temperature extremes.
TYPICAL APPLICATION
9
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112016PROFIBUS-DP
Master and Slave
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112016PROFIBUS-DP
Slave Only
• Connects your Allen-Bradley
ControlLogix as a slave to a
PROFIBUS network
• Fully integrated into the Rockwell
Automation environment
- No additional installation software
- Add-On-Profile for Rockwell
RSLogix5000
• Direct I/O mapping, no ladder logic
to write for data transfer between
module and CLX processor
• Conformal coating version:
- Provides environmental and
mechanical protection to significantly
extend the life of the components and
circuitry
- Protects electronic boards from
moisture and contaminants
• Typical applications:
-Marine
-Agro-Food
-Mining
- Harsh automotive, etc.
SPECIFICATIONS
SST-PB3S-CLX-RLL
SST-PB3S-CLXT-RLL eXTreme module
Description
• High-speed deterministic
communication
• Easy diagnostics:
Built-in LEDs and 4 characters display
• Full backplane compatible and easy
installation with no ladder logic
• Dedicated PROFIBUS Slave module
• All configuration done using the AOP
in RSLogix5000
•Auto-Boot
Included Hardware/Software
• Add-On-Profile for increased
functionality and reduced
commissioning time
• Support multiple modules in a chassis;
support local and remote chassis
• One PROFIBUS port, DB9 female,
galvanic insulation 1000V
• Speed: 9.6 Kbps up to 12 Mbps
• LEDs for system, communication,
and network status
• Simple data transfer up to 244
total words
• One serial port for upgrading
firmware
• Firmware upgradeable
• No additional software required for
configuration
10
Compatible Protocols
• Slave DP-V0
Conformance
• RoHS compliant
•CE
• Marine (RINA)
• PNO Certified
• cULus listed
• Class 1 Div 2, Groups A, B, C, and D
• Ex (ATEX)
• Korea CC
SST-PB3S-CLXT-RLL eXTreme:
• Same specifications as
SST-PB3S-CLX-RLL plus:
• Conformal coating
• eXTreme components
• Ambient operating temperature:
-25 to 70°C
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
112016-0025
SST-PB3S-CLX-RLL
SST™ PROFIBUS Slave Only communication
module for Rockwell ControlLogix, includes
Remote Link Library
112016-0026
SST-PB3S-CLX-RLL-CC
SST™ PROFIBUS Slave Only communication
module for Rockwell ControlLogix, includes
Remote Link Library, conformal coated
SST-PB3S-CLXT-RLL
SST™ PROFIBUS Slave Only communication
module for Rockwell ControlLogix CLXT
(eXTreme), includes Remote Link Library,
conformal coated, eXTreme module
components
112016-0027
Conformal coating material is applied to electronic circuitry to act as protection against moisture dust,
chemicals, and temperature extremes.
TYPICAL APPLICATION
11
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112016PROFIBUS-DP
Slave Only
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell
ControlLogix
112019 AS-Interface Scanner
• Connects your Allen-Bradley
ControlLogix to an AS-interface
network
• Target markets: valve control, tank
farms, material handling, conveyors,
discrete manufacturing cells, packaging
machines, labeling machines, filling/
bottling machines
• Direct I/O mapping, no ladder logic
to write for configuration and data
transfer between module and CLX
processor
• Supports 2 independent AS-i networks
with up to 124 AS-i slave devices per
module
SPECIFICATIONS
SST-ASI-CLX
Description
• AS-i version 3.0
• High-speed deterministic
communications to open vendor
sensors and actuator devices
• Fast, easy setup to CLX backplane
• AS-i I/O data and status information
mapped into the CLX processor’s I/O
data
• Flash memory for storage of AS-i
master I/O configuration
• Easy diagnostics: Built-in LEDs
• Easy setup using 2 push buttons or
configuration software
• Operating temperature: 0 to 55°C
Included Hardware/Software
• Acts as 1756 input/output module
• Support multiple modules in a chassis
• 2x AS-interface Master channels
• Maximum slave supported: Up to 62 slaves on each channel
• AS-i cycle time: 150 μsec (number of slaves +2)
• 1 serial port for configuration and
diagnostics
• Firmware upgradeable
• Configuration and network diagnostic
tools included.
• OS supported: Win 98, Win NT4,
2000, XP, Vista 32-bit, Win 7 (32, 64-bit)
Compatible Protocols
• AS-interface Scanner compliant with
specification 3.0
Conformance
• RoHS compliant
• cULus listed
• CE
• AS-interface certified
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
SST-ASI-CLX
112019-0001
AS-interface Communication module for
Rockwell ControlLogix, includes configuration
cable and software
USB to Serial DB9 cable, commercially available if required
12
Page Intentionally Left Blank
13
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell
CompactLogix
112073 Modbus/TCP, and
Modbus Serial Protocols
Standard Version
Plus Version
• Connects your Allen-Bradley
CompactLogix to a Modbus Ethernet
or Modbus Serial network
• Modbus Ethernet and Modbus Serial
at the same time- Extremely flexible,
easy upgrades to Ethernet based
devices
• Two Modbus Serial Ports, (Software
Configurable)- More value, handles
any Modbus serial application
• One Modbus Ethernet Port, (Software
Configurable)- suitable for any
Modbus TCP/UDP application
• Micro SD Card slot- Configuration
files, user manuals on SD card; also
fast, easy module replacement
• 10/100 Mb Ethernet Port- Fast
configuration downloads, no Logix
Ethernet port burden, low-cost cable
• Module acts as a co-processor
enhancing PLC performance
SPECIFICATIONS
SST-ESR2-CPX-S
Standard Version
SST-ESR2-CPX-P
Plus Version
Description
• Supports multiple modules in rack
• Supports CompactLogix L2, L3
processors with 1769 IO bus
capability Ver 15 and greater
• Operating temperature: 0 to 60°C
• Storage temperature: -40 to 85°C
• Relative humidity: 5% to 95%,
non-condensing
• Independent, 3 electrically isolated
communication ports, 2,500 Volts
• Modbus Master and/or Slave
functionality, ASCII and RTU formats
• Modbus TCP/UDP, client and server
supported
• One Micro SD Card Slot, SD card
included, configuration files, manuals
• 1x Ethernet, 10/100 Mbps,
RJ45 (also for configuration and
diagnostics)
• 2x Serial, 110 bps to 115.2
kbps,RS232/RS485/RS422, RJ45
(DB9 male supplied cable)
• OS supported: Windows XP, 7 (32,
64-bit), Vista, 8 (32, 64-bit)
• Paging access (AOI provided), with up
to 32k words shared for input, output
and status data (plus version)
Included Hardware/Software
• One, SST-ESR2-CPX-(S/P) Universal
Modbus Module
• One, Micro SD card
• One, product CD (engineering tools,
configuration console)
• Two, 45 cm, RJ-45 to DB-9 male
patch cables
Cyclic Function Screen Showing Data
Overlapping Errors, Data mapping,
Table Areas, Message Details
14
Compatible Protocols
• Modbus Master (RTU or ASCII)
• Modbus Slave (RTU or ASCII)
• Modbus TCP and UDP Client and Server
Conformance
• RoHS compliant
• CE certified
•FCC
• Lloyds (pending)
• Korea CC (pending)
• GOST (pending)
• ATEX (pending)
• UL Class I Div 2, Groups A,B,C,D
(pending)
Standard Version
• 496 Word Database
• 32 Modbus Commands/port
• Up to 32 devices per port
• OEM, machine builders, small
applications
Plus Version
• 32,000 Word Database
• 256 Modbus Commands/port
• Up to 27 serial devices per port and
128 Ethernet devices
• OEM, machine builders, large
networks SCADA applications
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
112073-0006
SST-ESR2-CPX-S
SSTtm Universal Modbus Module for
CompactLogix, Standard version
112073-0005
SST-ESR2-CPX-P
SSTtm Universal Modbus Module for
CompactLogix, Plus version
TYPICAL APPLICATION
15
Brad® SSTtm Communication
Module for Rockwell
CompactLogix
112073 Modbus/TCP, and
Modbus Serial Protocols
Standard Version
Plus Version
Page Intentionally Left Blank
16
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell
CompactLogix and
MicroLogix 1500
112019 AS-interface Scanner
• Connects Allen-Bradley CompactLogix
and MicroLogix 1500 PLCs to an ASinterface network
• Target markets: valve control, tank
farms, material handling, conveyors,
discrete manufacturing cells, packaging
machines, labeling machines, filling/
bottling machines
• Direct I/O mapping, no ladder logic
to write for configuration and data
transfer between module and CPX
processor
• Supports 1 independent AS-i networks
with up to 62 AS-i slave devices per
module
SPECIFICATIONS
SST-ASI-CPX
Description
• AS-i version 3.0
• High-speed deterministic
communications to open vendor
sensors and actuator devices
• Fast, easy setup to CPX backplane
• AS-i I/O data and status information
mapped into the CPX processor’s I/O
data
• Flash memory for storage of AS-i
master I/O configuration
• Easy diagnostics: Built-in LEDs
• Easy setup using 2 push buttons or
configuration software
• Operating temperature: 0 to 55°C
Included Hardware/Software
• 1x AS-interface Master channels
• Maximum slave supported:
Up to 62 slaves on each channel
• AS-i Cycle Time: 150 μsec
(number of slaves +2)
• 1 serial port for configuration and
diagnostics
• Firmware upgradeable
• Configuration and network diagnostic
tools included.
• OS supported: Win 98, Win NT4,
2000, XP, Vista 32-bit, Win 7 (32, 64-bit)
Compatible Protocols
• AS-interface Scanner compliant with
specification 3.0
Conformance
• RoHS compliant
• cULus listed
• CE
• AS-interface certified
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
SST-ASI-CPX
112019-0002
AS-interface Communication module for
Rockwell CompactLogix, MicroLogix 1500 PLCs,
includes configuration cable and software
USB to Serial DB9 cable, commercially available if required
17
FEATURES AND BENEFITS
Brad® SSTtm Communication
Module for Rockwell SLC 500
112016PROFIBUS-DP
Master and Slave
• Connects your Allen-Bradley SLC 500
to a PROFIBUS network
• Direct I/O mapping, no ladder logic
to write for configuration and data
transfer between module and SLC processor
• Simultaneous operation of PROFIBUS
DP Master and Slave
SPECIFICATIONS
Description
• High speed deterministic communication
• Fast, easy set up in SLC backplane;
PROFIBUS IO data is automatically
mapped into the SLC processor’s I, O,
MO and MI files
• Easy diagnostics: Built-in LEDs
• Manage DP Master and Slave modes
simultaneously
• Auto-Boot
(configuration stored in flash)
• Engineering Tools:
- Configuration console
- Test and diagnostic tools
Included Hardware/Software
• Acts as 1746 input/output module
• Support multiple modules in a chassis
• 1 PROFIBUS port, DB9 female,
galvanic insulation 1000V
• Speed: 9.6 Kbps up to 12 Mbps
• I/O mapping:
- I and O Files—
32 words in, 32 words out
- M1 and M0 Files—
1000 words in/out
• 1 serial port for configuration
and diagnostic
• Firmware upgradeable
Compatible Protocols
• Master DP-V0 Class-1 and Class-2
• Master DP-V1 Class-1 and Class-2
• Slave DP-V0
• FDL Send/Receive
Conformance
• RoHS compliant
• CE
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
SST-PB3-SLC
112016-0022
PROFIBUS Communication module for Rockwell SLC 500
18
FEATURES AND BENEFITS
• Connects your Allen-Bradley SLC 500
to a AS-interface network
• Target markets: Factory automation,
Process control, Complex machines,
etc
• Direct I/O mapping, no ladder logic
to write for configuration and data
transfer between module and
SLC processor
• Supports 2 independent AS-i networks
with up to 124 AS-i slave devices
Brad® SSTtm Communication
Module for Rockwell SLC 500
112019 AS-interface Scanner
SPECIFICATIONS
Description
• High speed deterministic communication
• Fast, easy setup to SLC backplane
• AS-i I/O data mapped into the SLC
processor’s I/O files
• Status information is mapped into the
M0 and M1 files
• Multiple SST-ASI-SLC modules can
be used in one SLC rack
• Configure scanner with
Rockwell RSLogix 500
• Flash memory for storage of AS-i
master I/O configuration
• Easy diagnostics: Built-in LEDs
Included Hardware/Software
• Acts as 1746 input/output module
• Support multiple modules in a chassis
• 2x AS-interface Master channels
• Maximum slave supported: Up to 62
slaves on each channel
• AS-i cycle time: 150 µsec
(number of slaves +2)
• AS-I connector: 4-pin combicon connector
• I/O mapping:
- I and O files: 32 words in, 32 words
out
- M1 and M0 files: 461 words in/out
• 1 serial port for configuration and
diagnostic
• Firmware upgradeable
Compatible Protocols
• AS-interface Scanner compliant with
specification 3.0
Conformance
• RoHS compliant
• CE
• AS-interface certified
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
SST-ASI-SLC
112019-0004
AS-interface Communication module for Rockwell SLC 500
19
FEATURES AND BENEFITS
Brad® SSTtm PROFIBUS
Remote Module
112016PROFIBUS-DP
Master and Slave
• Connects any Rockwell Automation
Logix controller (CompactLogix,
ControlLogix, GuardLogix,) with
EtherNetI/P connectivity to a
PROFIBUS network
• The PB3 module can be installed close
to PROFIBUS field devices, reducing
expensive PROFIBUS cabling
• No ladder logic to write for
configuration and data transfer
between PB3 Remote module and
Logix processor
• Unique remote concept
- No rack limitation of Rockwell Logix controllers backplane
- Flexible installation design; the PB3
Remote module can be installed at
the most convenient place (cabinet, on-machine, etc)
- Up to 2kbyte Input + 2kbyte Output
PROFIBUS process data
- Fits in with wireless architecture by
connecting a wireless access point to
the Ethernet port
• Target markets: Factory automation,
process control, complex machines,
and more
• Fully integrated into the Rockwell
Automation environment
- Add-On-Instructions (.L5X); Import
PROFIBUS I/O process variables into
RSLogix 5000 tags; allow the user to
use process variable names instead of
arrays of bit, byte, word or float
- EDS file for RSLinx
• Implement redundancy scenario
- 2x Logix controllers connected to
a single PB3 Remote Module, or
implementing PLC redundancy
- 1x Logix controller connected
to 2x PB3 Remote Modules, for
implementing PROFIBUS master
redundancy
• Conformal coating version; improves
and extends the working life and
ensures security and reliability of
performance in extreme or humid
conditions. Typical applications:
Marine, Agro-Food, Mining, Harsh
automotive, etc.
Technical Data
• Acts as “Linking Device” remote
module
• 1x PROFIBUS port, DB9 female,
galvanic insulation 500V
• Speed: 9.6 Kbps up to 12 Mbps
• Up to 1984 input bytes and 1968
output bytes
• 2x RJ45 Ethernet port switch
- 10/100 Mbps, auto negotiation
- I P addressing (via 2 rotary switches): DCHP (default), DHCP
with name (“SST_PB3_xxx”),
Factory fixed, factory selectable,
flash saved (via 0xF5/0xF6 EIP
objects)
- Manages duplicate IP addressing
-S
upport of DLR (Device Level Ring
as a ring node) - higher resiliency
from loss of one network connection
• Built-in diagnostics LEDs:
-4
x module status (system fault,
PROFIBUS state, bus fault, and
PLC RUN/PROG)
-3
x Ethernet: IP status, link (port 1, port 2)
• Operating temperature:
0 to +65°C
-25 to +70°C (Coated version)
• Storage temperature: -40 to +85°C
• DIN Rail mounted
• Compact dimensions: 18 x 7 x 16 cm
• Power supply: 24V
• Firmware upgradeable
SPECIFICATIONS
Description
• High speed deterministic communication
• Manage DP Master and Slave modes
simultaneously
• Allows changes to PROFIBUS
configuration with PLC in RUN mode
• Dynamically add/remove PROFIBUS
slaves from the scan list
• CommDTM driver for FDT Frame
engineering software (AssetCentre™,
PACTware™, Field Care™)
- PROFIBUS Master DP-V1 configuration
-D
evice detection
-D
evice diagnostics
• Auto-Boot (configuration stored in flash)
• PROFIBUS configuration console
-R
emote DP slave configuration and
diagnostics
- Automatic DP slave detection
- Automatic naming of I/O process
variable based on GSD file
-E
xport of I/O process variables in
RSLogix L5X format
20
Protocols
• Master DP-V0 Class-1 and Class-2
• Master DP-V1 Class-1 and Class-2
• Slave DP-V0
Conformance
• ODVA and PROFIBUS certified
product
• CE, RoHS, REACH, UL listed
• Class 1/Div 2- Groups A, B, C and D
for hazardous (Classified) locations
(coated version)
• RINA Marine Certificate
ORDERING INFORMATION
Engineering No.
Order No.
Description
SST-PB3-REM
112016-5000
SST™ PROFIBUS Remote Module for
Rockwell Automation Logix controllers
112016-5001
SST™ PROFIBUS Remote Module
for Rockwell Automation Logix controllers,
coated version
SST-PB3-REM-CC*
Brad® SSTtm PROFIBUS
Remote Module
112016PROFIBUS-DP
Master and Slave
* Conformal coating material is applied to electronic circuitry to act as protection against moisture,
dust, chemicals, and temperature extremes.
TYPICAL APPLICATION
REMOTE MODULE SOFTWARE
PROFIBUS Engineering Console
Dynamic Add-On-Instructions based on
PROFIBUS Configuration
21
Direct Access in RSLogix to
PROFIBUS tags
FEATURES AND BENEFITS
Brad® SSTtm IP67
PROFIBUS Remote Module
112016PROFIBUS-DP
Master and Slave
• Connects any Rockwell Automation
Logix controller with EtherNet/IP
connectivity to a PROFIBUS network
• Harsh-duty IP67-rated design for
on-machine or in-field mounting.
Perfectly fit new Armor GuardLogix
PLCs.
• The PB3 module can be installed close
to PROFIBUS field devices, reducing
expensive PROFIBUS cabling
• No ladder logic to write for
configuration and data transfer
between PB3 Remote module and
Logix processor
• Unique remote concept
- No rack limitation of Rockwell Logix
controller backplane
- Flexible installation design; the PB3
Remote module can be installed at
the most convenient place
- Up to 2kbyte Input + 2kbyte Output
PROFIBUS process data
- Fits in with wireless architecture by
connecting a wireless access point to
the Ethernet port
• Target markets: Factory automation,
Process control, Complex machines,
etc.
• Fully integrated into the Rockwell
Automation environment
- Add-On-Instructions (.L5X); Import
PROFIBUS I/O process variables
into RSLogix 5000 tags; allow the
user to use process variable names
instead of arrays of bit, byte, word or
float
- EDS file for RSLinx
• Implement redundancy scenario
- 2x Logix controllers connected to
a single PB3 Remote Module; or
implementing PLC redundancy
- 1x Logix controller connected
to 2x PB3 Remote Modules; for
implementing PROFIBUS master
redundancy
Technical Data
•A
cts as “Linking Device” remote
module
•2
x Power connectors, M12, male plus
female, A-Coded (protected against
power crossing)
•2
x PROFIBUS ports, B-coded female,
galvanic insulation 500V
• Speed: 9.6 Kbps up to 12 Mbps
•U
p to 1984 input bytes and 1968
output bytes
•2
x Ethernet port switch, M12
D-Coded
- 10/100 Mbps, auto negotiation
- I P addressing (via 2 rotaryswitches):
DCHP (default), DHCP with name
(“SST_PB3_xxx”), factory fixed,
factory selectable, flash saved (via
0xF5/0xF6 EIP objects)
- Manages duplicate IP addressing
-S
upport of DLR (Device Level Ring
as a ring node) – higher resiliency
from loss of one network connection
• Built-in diagnostics LEDs:
-4
x module status (system fault,
PROFIBUS state, bus fault, and
PLC RUN/PROG)
-3
x Ethernet: IP status, Link (port 1, port 2)
• Operating temperature:
-25 to +70°C
• Storage temperature: -40 to +85°C
• Compact dimensions: 22 x 6 x 3.6 cm
• Power supply: 24 VDC
• Firmware upgradeable
SPECIFICATIONS
Description
• High speed deterministic
communication
• Manage DP Master and Slave modes
simultaneously
• IP67-rated dust and water resistant.
Tested to withstand shock, highvibration and high temperatures
• Allows changes to PROFIBUS
configuration with PLC in RUN mode
• Dynamically add/remove PROFIBUS
slaves from the scan list
• CommDTM driver for FDT Frame
engineering software (AssetCentre™,
PACTware™, FieldCare™…)
- PROFIBUS Master DP-V1
configuration
- Device detection
- Device diagnostics
• Auto-Boot (configuration stored in
flash)
• PROFIBUS Configuration console
- Remote DP slave configuration and
diagnostics
- Automatic DP slave detection
- Automatic naming of I/O process
variable based on GSD file
- Export of I/O process variables in
RSLogix L5X format
22
Protocols
• Master DP-V0 Class-1 and Class-2
• Master DP-V1 Class-1 and Class-2
• Slave DP-V0
Conformance
• ODVA and PROFIBUS certified
product
• CE, RoHS, REACH, UL listed
• KoreanCC, China (CCC)
Engineering No.
Order No.
SST-PB3-REM-R
112016-5002
ORDERING ORDERING
INFORMATION
ORDERINGINFORMATION
INFORMATION
NEW NEW PPAGE AGE SST™ IP67 PROFIBUS Remote Module for
Rockwell Automation Logix controllers
Engineering No.No.
Engineering No.Engineering
Order No.
Brad SST IP67
PROFIBUS Remote
Module
Description
Order
No.No.
Order
Description
Description
Description
112016 PROFIBUS-DP
and
Master
Slave
Brad
SST
IP67
tmBrad
SST
IP67
Brad SST
IP67
PROFIBUS
Remote
Remote
PROFIBUS
PROFIBUS
Remote
Module
Module
Module
112016PROFIBUS-DP
112016
112016 PROFIBUS-DP
PROFIBUS-DP
Master
and
Slave
Master
andSlave
Masterand
Slave
®
TYPICAL APPLICATION
SST™
IP67
PROFIBUS
Remote
Module
forfor
SST™
IP67
PROFIBUS
Remote
Module
SST-PB3-REM-R
112016-5002
SST™ IP67
PROFIBUS
Remote
Module for
SST-PB3-REM-R
Rockwell
Automation
Logix
controllers
SST-PB3-REM-R
112016-5002 112016-5002
Rockwell
Automation
Logix
controllers
Rockwell Automation Logix controllers
TYPICAL
APPLICATION
TYPICAL
APPLICATION
TYPICAL APPLICATION
MODULE
REMOTE
SOFTWARE
REMOTE MODULE
SOFTWARE
REMOTE
REMOTEMODULE
MODULESOFTWARE
SOFTWARE
Direct Access in RSLogix to PROFIBUS tags
PROFIBUS Engineering Console
Dynamic Add-On-Instructions based on PROFIBUS
configuration
2
23
2 2
FEATURES AND BENEFITS
Brad® SSTtm DeviceNet*
Remote Scanner
112034 DeviceNet Control
over Ethernet
• High performance DeviceNet protocol executed via Remote DeviceNet™
Scanners
• User interface DLL/API is completely
backward compatible with existing
applications and local DeviceNet
interface cards
• Diagnostic LEDs
• UCMM (Unconnected Message
Manager) capable; Group 1, 2, and 3
dynamic explicit connections
supported
• Provides simultaneous execution of
Group 2 Client (Master) and Server
(Slave) operation
• Supports all DeviceNet standard baud
rates: 125, 250, and 500 Kbaud
• Supports Poll, Strobe, Change of
State (COS) and Cyclic I/O messaging
• Provides Client (Master) explicit messaging to slave devices
• Backward compatible DLL preserves
existing investment
• DIN rail mount allows distribution to
machine level
• Frees up PC slots by placing scanner
cards remotely
• Manage your DeviceNet application
across an Ethernet LAN
• Capable of updating DeviceNet I/O
faster than a PCI version
• Reduce infrastructure costs by using
cheaper Ethernet cable and fewer and/
or less expensive PCs
Hardware Specifications
• Diagnostic LEDs:
- Remote Scanner—
Power, system status
- DeviceNet—
Power, communication, health
- Ethernet—
Link, 10/100 MBaud, activity
• Remote scanner power:
1
0–30VDC, 330mA typical
(male Nano-Change® M8 connector)
Network Specifications
• Protocol:
- DeviceNet Master—
Group 2 Client, Group 2 only Client
- DeviceNet Slave—
Group 2 Server
- Isolated CAN physical layer on each
channel
• Cable:
- DeviceNet—shielded twisted pair,
compatible with target network
- Ethernet—Cat 5e shielded
• Connector:
- DeviceNet—Compliant male Micro-Change® M12 connector
- Ethernet—RJ45
• DeviceNet power:
11-24 VDC, 50 mA typical
• Isolation: 500 V
• Data rate:
- DeviceNet—
125 Kbps, 250 Kbps and 500 Kbps
- Ethernet—10/100 Mbps
SPECIFICATIONS
OS and Drivers Supported
• Microsoft® Windows 7 (64-bit), Vista,
XP for both drivers and diagnostic
tools
• Example C source code and Windows
DLLs for custom driver development
Software Tools
• Diagnostic and test tools are
available that enable fast integration
of industrial communication into your
application.
Conformance
• RoHS Compliant: Yes
• Approvals: CE
• ODVA DeviceNet Conformance Test
Environmental
• Humidity: 5% to 95% non-condensing
Physical
• Operating temperature:
0 up to +50°C
• Storage temperature:
-40 up to +85°C
*DeviceNet is a trademark of Open DeviceNet Vendor Association (ODVA)
24
ORDERING INFORMATION
Engineering No.
Standard Order No.
Product Description
SST-EDN-1
112034-0021
Remote DeviceNet Scanner (without cables)
Remote DeviceNet Scanner with cable kit
(DeviceNet and Power)
SST-EDN-1-C2
112034-0026
Single-ended power cable: 3-pole, M8
connector on one end, 2 meters (6.6ft), UL/CSA
cable, Cat. No. 403000A1ı0M020
Single-ended DeviceNet cable: 5-pole,
M12 connector on one end,
2 meters (6.6ft), UL/CSA cable,
Cat. No. DND20A-M020
TYPICAL APPLICATION
REMOTE DIAGNOSTIC SOFTWARE
*DeviceNet is a trademark of Open DeviceNet Vendor Association (ODVA)
25
Brad® SSTtm DeviceNet*
Remote Scanner
112034 DeviceNet Control
over Ethernet
FEATURES AND BENEFITS
Brad® applicom®
Network Interface Card
112000 Industrial Ethernet
• Fast data acquisition between PC-based applications and industrial
devices connected to Ethernet TCP/IP
• On board co-processor eliminates data
bottlenecks, ensuring delivery of time
critical information
• “All-in-One” - All protocols included
in the package · Best choice for HMI/
SCADA applications
• High value engineering software tools;
enabling fast integration of industrial
communication into your applications
(configuration, diagnostic, data
servers, development libraries)
• One configuration and one diagnostic
tool whatever the protocols used
• Quick “Return-On-Investment”; Single
development library and OPC server
reduce the time required to learn and
integrate applicom® products in your
architectures
• Simultaneously run all TCP/UDP
protocols in Client/Server modes
• Combine several cards (up to 8) and
run simultaneously from 1 to 32
protocols in a single PC
• Combo versions:
- Ethernet + PROFIBUS (1.5 Mbps)
- Ethernet + Serial (38.4 Kbps)
Included Hardware/Software
• Bus Format:
-P
CI Universal bus 3.3V/5V (PCI-X
compatible)
- PCI Express 1x
• Hardware plug and play
• AMD SC520
• 16 Mb SDRAM
• 4 Mb flash memory
• One Ethernet port:
-F
ast Ethernet 10/100 Mbps, auto
negotiating
-B
ase-T (RJ45), 4 LEDs (Rx, Tx,
Link, 10/100)
Compatible Protocols
Ethernet TCP/IP
(Client/Server modes)
• Altus Alnet II (AL 200x, Webgate)
• Alstom SRTP (C80-35, C80-75)
• Allen-Bradley EtherNet/IP(PCCC)
(Logix, PLC-5 and SLC 500)
• Fanuc SRTP (90-30, 90-70)
• Mitsubishi Electric Melsec (A, Q)
• Omron FINS (C, CV, CS)
• Schneider Electric Open Modbus TCP
• Schneider Electric UNI-TE
(Premium and Micro)
• Siemens Industrial Ethernet
(S5, S7, TI)
• UDP Send/Receive (Free messaging)
SPECIFICATIONS
Description
• Engineering tools:
- Engineering console
- Test and diagnostic tools
• Compatible data servers:
- OPC DA v3.0
- Wonderware® DAServer
- Wonderware I/O (SuiteLink/
FastDDE)
• Includes development libraries:
-Visual Studio 6 (C++/C)
- Visual Studio 2005 (VB .NET/C+)
• Supported OS:
- Windows (32-bit and 64-bit):
8, 7 2012/2008/2003 Server, XP
Ethernet ISO
• Schneider Electric Ethway
• Siemens Industrial Ethernet ISO
(S5, S7, TF and TI)
Conformance
• RoHS compliant
• CE
• OPC certified
26
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
APP-ETH-PCU-C
112000-0005
PCU2000ETH
PCI Network Interface Card for Ethernet
112000-5026
PCIE2000ETH
PCI Express Network Interface Card for
Ethernet
APP-ETH-PCIE
TYPICAL APPLICATION
27
Brad® applicom®
Network Interface Card
112000 Industrial Ethernet
Page Intentionally Left Blank
28
FEATURES AND BENEFITS
Brad® applicom®
Network Interface Card
112011PROFIBUS
for Scada/HMI
• Fast data acquisition between PC-based applications and industrial
devices connected to PROFIBUS
• On board co-processor eliminates data
bottlenecks, ensuring delivery of time
critical information
• “All-in-One” - All protocols included
in the package · Best choice for HMI/
SCADA applications
• High value engineering software tools;
enabling fast integration of industrial
communication into your applications
(configuration, diagnostic, data
servers, development libraries)
• One configuration and one diagnostic
tool whatever the protocols used
• Quick “Return-Of-Investment”; Single
development library and OPC server
reduce the time required to learn and
integrate applicom® products in your
architectures
• Simultaneously run all PROFIBUS
protocols
• Combine several cards (up to 8) and
run simultaneously from 1 to 32
protocols in a single PC
• Combo protocol: Run all PROFIBUS
protocols simultaneously (DP, PPI/
PPI+, S7/ MPI, FDL)
• Compatible with:
- Simatic® S7 Series
(S7-1200,S7-200, S7-300, S7-400)
- Simatic® SS Series
(95U, 115U, 135U, 155U)
Included Hardware/Software
• Bus format:
- PCI Universal bus 3.3V/5V (PCI-X
compatible)
- PCI Express 1x
• Hardware plug and play
• AMD SC520
• 16 Mb SDRAM
• 4 Mb flash memory
• 1 PROFIBUS port, DB9 female,
galvanic insulation 500V
• Speed: 9.6 Kbps up to 1.5 Mbps
Compatible Protocols
• Master DP-V0, Class-1 and Class-2
• S7/MPI Client
• FDL S5 Master
• PPI/PPI+ Master
• Free FDL Send/Receive
SPECIFICATIONS
Description
• Engineering tools:
- Engineering console
- Test and diagnostic tools
• Compatible data servers:
- OPC DA v3.0
- Wonderware® DAServer
-W
onderware I/O (SuiteLink/
FastDDE)
• Includes development libraries:
- Visual Studio 6 (C++/C)
- Visual Studio 2005 (VB .NET/C#)
• Supported OS:
- Windows
(32-bit and 64-bit):
8
, 7 2012/2008/2003 Server, XP
Conformance
• RoHS compliant
• CE
• OPC certified
• PCI Express certified
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
APP-PFB-PCU-C
112011-0004
PCU1500PFB PCI Network Interface Card for PROFIBUS
APP-PFB-PCIE
112011-5026
PCIE1500PFB PCI Express Network Interface Card for PROFIBUS
29
Page Intentionally Left Blank
30
FEATURES AND BENEFITS
• Fast data acquisition between PC-based applications and industrial
devices connected to serial networks
• On board co-processor eliminates data
bottlenecks, ensuring delivery of time
critical information
• “All-in-One” - All protocols included
in the package · Best choice for HMI/
SCADA applications
• High value engineering software tools;
enabling fast integration of industrial
communication into your applications
(configuration, diagnostic, data
servers, development libraries)
• One configuration and one diagnostic
tool whatever the protocols used
• Quick “Return-Of-Investment”; single
development library and OPC server
reduce the time required to learn and
integrate applicom® products in your
architectures
• Combine several cards (up to 8) and
run simultaneously from 1 to 32
protocols in a single PC
• Electrical interfaces available:
RS232C, RS485/RS422, Current
Loop; all with or without galvanic
insulation (opto couplers) Brad® applicom®
Network Interface Card
Included Hardware/Software
• Bus format:
- PCI Universal bus 3.3V/5V
(PCI-X compatible)
- PCI Express 1x
• Hardware: plug and play
• AMD SC520
• 16 Mb SDRAM
• 4 Mb flash memory
• 1x Serial Port:
- D-Sub, 9pin, male
- 2 leds (TX/RX)
- 50 bps to 38.4 Kbps
Electrical interface:
- RS485/RS422 with galvanic
insulation (500 V)
• Modbus Master (ASCII and RTU)
• Modbus Slave (ASCII and RTU)
• Omron Sysmac Way Master
• Saïa Burgess Controls S-Bus Master
(PCD Series)
• Schneider Electric Uni-Telway
Master/Slave (TSX 7 Series)
• Siemens 3964/3964R Free
or RK512 Master
• Siemens AS511 Master
(Simatic S5 Series)
• Siemens PPI/PPI+ Master
(Simatic S7-200 Series)
• Siemens Ti-Dir Master
(Simatic TI-505 Series)
Compatible Protocols
• Allen-Bradley DF1 Master
(PLC-5 and SLC Series)
• Elsag Bailey® Data Link Master
(5000 and 2000 Series)
• GE Fanuc SNPX Master
(90-xx and 80-xx Series)
• Moeller Group® SucomA Master
(PS32, PS316 Series)
Conformance
• RoHS compliant
• CE
• OPC certified
• PCI Express certified
112020 Serial Protocol
for Scada/HMI
SPECIFICATIONS
Description
• Engineering tools:
- Engineering console
- Test and diagnostic tools
• Compatible data servers:
- OPC DA v3.0
- Wonderware® DAServer
- Wonderware IO (SuiteLink/
FastDDE)
• Includes development libraries:
- Visual Studio 6 (C++C), Visual
Studio 2005 (VB, NET/C#)
• Supported OS:
- Windows (32-bit and 64-bit) 8, 7
2012/2008/2003 Server, XP
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
APP-SR1-PCU-C
112020-5017
PCU1000 PCI Network Interface Card for Serial networks
APP-SR1-PCIE
112020-5018
PCIE1000 PCI Network Interface Card for Serial networks
31
Page Intentionally Left Blank
32
FEATURES AND BENEFITS
Brad® applicomIO®
Network Interface Card
112000 Ethernet Fieldbus
•D
eterministic data acquisition for real
time PC-based control applications
•O
n board co-processor eliminates data
bottlenecks, ensuring delivery of time
critical information
• Very easy-to-use; no knowledge of
protocol required
• Remote access via TCP/IP connection;
to able configuration and diagnostic
when using real time OS (VxWorks,
Linux)
SPECIFICATIONS
Description
• Auto mapping of I/O in card DPRAM
• I/O exchange up to 14 Kbytes
• Hardware and software Watchdog
• Auto-Boot (Configuration stored in flash)
• Engineering tools:
- Engineering console with automatic
test and diagnostic tools
• Compabtible data servers:
- OPC DA v3.0, 2.05 and 1.0a
• Includes development libraries:
• Supported OS:
- Windows (32-bit and 64-bit):
8, 7 2012/2008/2003 Server, XP Embedded
- Others:
Linux, VxWorks, RTX VenturCom
Device Diagnostics
Included Hardware/Software
• PCI Universal bus 3.3V/5V
(PCI-X compatible)
• Hardware plug and play
• AMD SC520
• 16 Mb SDRAM; 4 Mb flash memory
• 1 digital input plus 1 digital output
• 1 Ethernet port:
- Fast Ethernet 10/100 Mbps, auto
negotiating
- Base-T (RJ45), 4 LEDs (Rx, Tx,
Link, 10/100)
Compatible Protocols
EtherNet/IP
• Scanner and adapter
• Explicit messaging (Client/Server)
• Up to 128 simultaneous CIP connections
• EtherNet/IP Devices supported:
Generic and Rockwell IO through EDS
files (FlexIO, CompactLogix, etc)
• IP address settings configurable via
the console or DHCP/BOOTP server
• Client DNS supported
Conformance
• RoHS compliant
• CE
• OPC certified
• ODVA conformance tested
Configuration Console
ORDERING INFORMATION
Engineering No.
Order No
Description
DRL-EIP-PCU
112000-5030
PCU-ETHIO PCI Network Interface Card for EtherNet/IP
DRL-EIP-PCIE
112000-5033
PCU-ETHIO PCI Express Network Interface Card for EtherNet/IP
33
FEATURES AND BENEFITS
Brad® Software Development
Kits EtherNet/IP Scanner
and Adapter
112106 Ethernet Software
Development Kits
• Scanner and adapter protocol stacks
can address both controller (Scanner)
or device (Adapter) manufacturers
who want to implement EtherNet/IP
networks
• Brad stacks have no hardware and
OS dependencies and can be easily
implemented on a large range of
hardware system platforms or
software operating systems
• Sample applications with source codes
are provided and can be quickly and
easily implemented
• OEM engineering console software
(EIP-CT) to quickly create
configuration files to initialize the
stack and perform commissioning and
diagnostic of connected devices (this
tool is protected by a USB dongle and
can be customer branded)
• Brad stacks are successfully tested
with ODVA conformance tool
• Molex can provide stack training,
technical support and engineering
development for both hardware and
software design
SPECIFICATIONS
EtherNet/IP Stack, SST-EIP-SCA
Basic Characteristics
• Conform to ODVA specifications
EtherNet/IP (vol 1-3.14, vol 2-1.15)
• CIP features:
- Implicit messaging (I/O process data)
- Explicit messaging (configuration
and diagnostic)
• Extensive Client/Server
messaging support
• Fully compatible with EtherNet/IP
conformance test suite CT11
• Stack resolution: Timing resolution
in microseconds
• Supported objects according to
CIP Standard
• Identity object
• Message router object
• Assembly object:
- Connection Manager Object
- TCP/IP Interface Object
- Ethernet link object
- QoS object
- And any user objects
SDK Package
• ANSI C source code
• Electronic documentation
• Implementation example on several
operating systems (Win32, Win64,
VxWorks 6.4/6.6/6.8, Linux)
• EDS sample
• STC sample for ODVA
conformance tool
• Sandbox application for testing
SDK API
• EIP_Trace to log messages from
target platform on a Windows host
• EIP_Tool to access CIP objects
34
Common Characteristics
• Hardware compatibility: 32-bit and
64-bit processor (Intel, PowerPC,
ARM, SH4 already validated)
• Supported operating system: Any OS
real-time or not (Windows, VxWorks,
Linux, etc.)
• Hardware compatibility: Supports
Motorola and Intel memory systems
• Stack implementation:
- Single or multi task
- Socket based or UDP optimization
• Code foot print (estimate but
highly customizable):
- 200 kB for Adapter
- 400 kB for Scanner
EtherNet/IP Configuration Tool (EIP-CT)
• Windows (32-bit and 64-bit): XP,
Vista, Seven, 2008 Server
• Generate scanner stack
configuration files
• EDS device library management
• Adapter commissioning (Automatic
device detection, online actions, etc.)
• Support of modular device like
Rockwell FlexI/O and PointI/O devices
with chassis and module management
• Integrated diagnostic
• OEM customization
• USB dongle protection
• Used by ODVA during plug fest
interoperability tests
TYPICAL STACK ARCHITECTURE
Brad® Software Development
Kits EtherNet/IP Scanner
and Adapter
112106 Ethernet Software
Development Kits
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
112106-5003
SDK-EIP-SCA
EtherNet/IP Scanner and Adapter SDK
112106-5009
SDK-EIP-SCA-L
EtherNet/IP Scanner and Adapter License Fee
112106-5004
SDK-EIP-SCA-UDP-1
EtherNet/IP Scanner and Adapter SDK – Update Contract – 1 year
112106-5025
SDK-EIP-SCA-UDP-3
EtherNet/IP Scanner and Adapter SDK – Update Contract – 3 years
112106-5011
SDK-EIP-SCA-CNF-U
EtherNet/IP Configuration Tool (EIP-CT) for Scanner SDK
112106-0000
SDK-EIP-ADP
EtherNet/IP Adapter SDK
112106-5000
SDK-EIP-ADP-UPD-1
EtherNet/IP Adapter SDK – Update Contract – 1 year
112106-5023
SDK-EIP-ADP-UPD-3
EtherNet/IP Adapter SDK – Update Contract – 3 years
SUPPORT/TRAINING INFORMATION
Engineering No.
Standard Order No.
Description
860000-0141
SDK-EIP-EDS
Engineering Support for EtherNet/IP SDK
860000-0143
SDK-EIP-TRN
EtherNet/IP SDK Training
35
FEATURES AND BENEFITS
Brad® Software Development
Kits CIP Safety DeviceNet*
Slave and EtherNet/IP Adapter
112115 DeviceNet Software
Development Kits
112116 Software Development
Kits - License
112117 EtherNet/IP Software
Development Kits
• Faster time-to-market with TÜV
approved stack
• Meets IEC 61508, SIL3 ensuring
international market acceptance
• Approved by TUV and tested by ODVA
means a high-quality solution for
minimal project risk and faster timeto-market
• Pre-tested modular ANSI C code
is easy to compile using standard
compilers; faster time-to-market
• Molex engineers can support protocolintegration requests minimizing
investment required for in-house
resources
• Designed for use with other Molex/
Brad offerings: Hardware (DN4
network interface cards), Software
(DeviceNet or EtherNet/IP software
stacks) which results in a complete
CIP communication solution
SPECIFICATIONS
CIP Safety Stack, SST-EIP-SCA
Description
• Design for dual channel architecture
(1oo2)
• ANSI C code for the safety portion of
the stack (Compliant with CIP Safety
Specification 2.1)
• ANSI C code for black-channel
components (NET_CTRL_IO)
• Interface specification for highintegrity and black-channel
environments
• Safety integration manual (including
safety measure requirements)
• Optionally, modified standard
CIP stacks (software/firmware)
for DeviceNet (Slave) or
EtherNet/IP (Adapter)
• Optionally, ANSI C code for the
platform adaptation layers
(both safety and non-safety)
• All documentation required by
certification bodies (TÜV, ODVA)
• Support during certification process
of vendor’s final product
Typical Products Requiring Safety
36
Conformance
• TÜV approved for SIL3 design
• ODVA conformance
TYPICAL STACK ARCHITECTURE
Brad® Software Development
Kits CIP Safety DeviceNet*
Slave and EtherNet/IP Adapter
112115 DeviceNet Software
Development Kits
112116 Software Development
Kits - License
112117 EtherNet/IP Software
Development Kits
ORDERING INFORMATION
Engineering No.
Standard Order No.
SDK-DNS-SAF
112115-0001
SDK-DNS-SAF-L
112116-0001
SDK-DNS-SAF-UPD-1
860000-0271
SDK-DNS-SAF-UPD-3
860000-0272
Network
Description
CIP Safety Software Development Kit
CIP Safety Software Development Kit, Royalty (per device)
DeviceNet
Slave
CIP Safety Software Development Kit – Update Contract – 1 year
CIP Safety Software Development Kit – Update Contract – 3 years
SDK-EIP-ADP-SAF
112117-0001
CIP Safety Software Development Kit
SDK-EIP-ADP-SAF-L
112116-0002
CIP Safety Software Development Kit, Royalty (per device)
SDK-EIP-ADP-UPD-1
860000-0271
SDK-EIP-ADP-UPD-3
860000-0272
EtherNet/IP
Adapter
CIP Safety Software Development Kit – Update Contract – 1 year
CIP Safety Software Development Kit – Update Contract – 3 years
SUPPPORT/TRAINING INFORMATION
Engineering No.
Standard Order No.
Description
SDK-CIP-SAF-TRN
860000-0291
Engineering Support for CIP Safety SDK
37
Page Intentionally Left Blank
38
FEATURES AND BENEFITS
Brad® Direct-Link® Windows
Compatible Protocol Drivers
112027 Serial and Ethernet
TCP/IP
• Direct-Link® SW1000 provides data
acquisition between Windows PC-based applications and industrial
devices connected to Ethernet TCP/IP
• Economic solution; well suited for embedded and light architecture (laptop, panel PC, MMI)
• 100% software solution; use PC COM
port or integrated Ethernet interface
• Wide variety of open and vendor specific industrial protocols
SPECIFICATIONS
Description
• Based on Windows TCP/IP socket
• All Ethernet protocols can run
simultaneously
• All Ethernet protocols can run
Client and Server modes
• Database (32 Kbits, 32 Kwords) for
Server mode to exchange data with
applications
Included Hardware/Software
• Engineering tools:
- Engineering console
- Test and diagnostic tools
• Compatible data servers:
- OPC DA v3.0, 2.05 and 1.0a
- Wonderware® DAServer
-W
onderware IO (SuiteLink/
FastDDE)
• Includes development libraries:
-V
isual Studio 6 (C++C), Visual
Studio 2005 (VB .NETC#)
• OS support:
Windows (32-bit and 64-bit):
8, 7 2012/2008/2003 Server, XP
• Software or USB dongle protection
Compatible Protocols
• Serial:
- Modbus Master (ASCII and RTU)
- Modbus Slave (ASCII and RTU)
- Fanuc SNPX Master
(90-xx and 80-xx Series)
- Schneider Electric Uni-Telway
Slave (TSX 7 Series)
- Siemens AS511 Master
(Simatic S5 Series)
- Siemens PPI/PPI+ Master
(Simatic S7-200 Series)
- Siemens Ti-Dir Master
(Simatic TI-505 Series)
• Ethernet TCP/IP:
- Altus Alnet II (AL200x, webgate);
Client/Server
- Alstom SRTP (C80-35, C80-75);
Client/Server
- Allen-Bradley Logix5000
(ControlLogix and FlexLogix);
Client/Server
- Fanuc SRTP
(C90-30, C90-70); Client/Server
- Mitsubishi Electric Melsec
(A and Q);
Client/Server
- Omron FINS (C, CV, CS);
Client/Server
- Schneider Electric Modbus TCP
and UDP; Client/Server
- Schneider Electric UNI-TE
(Premium and Micro); Client/Server
- Siemens Industrial Ethernet
(S5, S7, TI); Client/Server
ORDERING INFORMATION
Engineering No.
Standard Order No.
Description
DRL-ALL-SWF-S
112027-0002
SW1000 software drivers, Full tags, Software key protection
DRL-ALL-SWF-U
112027-0003
SW1000 software drivers, Full tags, USB dongle protection
DRL-ALL-SWL-S
112027-0005
SW1000 software drivers, Full tags, Software key protection
DRL-ALL-SWL-U
112027-0006
SW1000 software drivers, Full tags, USB dongle protection
39
Quickly identify problems relating to network power, data errors and excessive
bandwidth consumption for your DeviceNet network.
Brad® DeviceNet*
Diagnostic Tools
112008eNetMeter™
DN NetAlytix™
eNetMeter DN and NetAlytix
eNetMeter DN is a passive device that continuously monitors a DeviceNet network
and sends the information over Ethernet to a PLC or PC monitoring system. The
information can be used to proactively respond to out-of-tolerance parameters
before network failure occurs. Optionally, data can be accessed through NetAlytix
software, an OPC server or a DLL.
FEATURES AND BENEFITS
eNetMeter, 112008-0008
• Continuously monitors a DeviceNet
network in a passive state
• Provides feedback to an EtherNet/IP™
master or one of three methods to a
personal computer (PC) residing on
Ethernet:
- NetAlytix™ software
- OPC server
- DLL interface
• High-speed sampling of network parameters
- Signals are sampled millions of
times per second providing accurate
values
• Email based notification feature in
now supported within the NetAlytix
software tool
• AOI supports simple integration with
Logix based controller allowing easy
data transfer for an eNetMeter
• Information captured includes:
-O
verall network status and measurements
- I ndividual node status and measurements
-D
etailed measurements of power
(V+, V-), signal (CANH, CANL) and
shield parameters
• Warning and fault flags indicate when
a value has exceeded a set tolerance
(levels are customizable)
• NetAlytix software enables quick
graphical access to network issues
including CAN and power waveform
details
- e asily allows comparison of a known
good waveform to current readings
in order to diagnose problems
Physical
• Dimensions: 142.00mm (5.60”) high;
102.00mm (4.08”) deep;
38.00mm (1.53”) wide
• Connectors: DeviceNet—5-pole M12 Micro-Change®
Ethernet—RJ-45
• Enclosure: IP20
• Mounting:
DIN rail or panel (screw) mounted
• USB: USB 2.0 master, for transfer/
storage of configuration parameters
• Operating temperature: 0 to 60°C
• Storage temperature: -5 to 75°C
• Humidity: 5% to 95% non-condensing
Software
• NetAlytix full version includes OPC
Server and API/DLL
• Supported within Windows 8, Server
2012, Windows 7 (64-bit), Vista, XP
SPECIFICATIONS
Electrical
• Input power (Aux. or DeviceNet)
11 to 25V DC, 300 mA (typical at 24 VDC)
• Data rate: D
eviceNet: 125K, 250K and 500K baud
Ethernet: 10/100 M baud
Mechanical
• Diagnostic LEDs and control: R
eady, System/Boot, Power & Comm;
Reset (recessed)
Environmental
• Approvals: CE, cULus
• RoHS Compliant: Yes
eNetMeter PTU, 112008-0016
*DeviceNet is a registered trademark of Open DeviceNet Vendor Association
40
ORDERING INFORMATION
Engineering No.
Standard Order No.
Product Description
SST-ENM-DN1
112008-0008
eNetMeter™ DN diagnostic tool for DeviceNet
SST-NAS-DN1
112008-0011
NetAlytix™ software for eNetMeter DN
(includes full application, DLL/API, OPC Server)
SST-ENM-SKT
112008-0012
Bundle of eNetMeter DN (1120080008) and
NetAlytix (1120080011), with a limit of
one per partner or end-customer site
SST-ENM-PTU
112008-0016
Bundle of eNetMeter DN (112008-0008) and
NetAlytix (112008-0011) in portable test case
(IP54) with DC power and external ports for
network as well as AC power connections
Brad® DeviceNet*
Diagnostic Tools
112008eNetMeter™
DN NetAlytix™
NetAlytix™ Software V2
Data
Data Waveform Area (colours
Waveform
match DeviceNet wiring)
Area
(colours
match
DeviceNet
eNetMeter Monitor
wiring)
software - included in
NetAlytix software
Favourites Area (User defines own)
All Warnings & Faults
are displayed together
Drop-down hierarchy shows all
active eNetMeters and network
nodes being monitored
All data shown for network area selected in
drop-down hierarchy (left panel)
APPLICATION EXAMPLE
TypicalTypical
PLC/PAC
(can access
PLC/PAC
(can
eNetMeter™
DN
data
™ with Add-On
access eNetMeter DN data)
Instruction
PC running NetAlytix™ software
I/O Devices
P/S
(24VDC)
*DeviceNet is a registered trademark of Open DeviceNet Vendor Association
41
eNetMeter™ DN
Quickly identify problems relating to network power, data errors and excessive
bandwidth consumption for your DeviceNet network.
Brad® DeviceNet*
Diagnostic Tools
112008NetMeter®
NetMeter
NetMeter cuts troubleshooting time by providing technical details, yet it simplifies
and summarizes, allowing both a DeviceNet expert and novice to effectively identify
and diagnose network problems. It summarizes DeviceNet bus health by displaying
a happy face icon, indicating a healthy network; a sad face, indicating a serious
problem; or a neutral face, indicating nominal performance (a good indication to
repair things before they actually fail). NetMeter then walks the user through each
fault condition and its potential source.
FEATURES AND BENEFITS
NetMeter, 11200-80013
• Certifies proper network operation:
- Measures 677 key network
parameters
- Compares with DeviceNet
specification
• Battery-powered:
- Save readings for off-line analysis
• Accelerates fault troubleshooting:
- AutoSearch finds all bad network
parameters
- Full traffic and error analysis by
node address
- Power quality, shield voltage, signal
quality
SPECIFICATIONS
NetMeter Kit, 112008-0014
Electrical
• Power supply:
7V—30V (30 mA at 24V) battery 2x
AA alkaline (for offline review
of stored measurements)
Mechanical
• Baud rates supported: 125K, 250K, 500K (auto-detect)
• Analog range (with over/under range
indication):
- Bus Power: 0 to 25V
- Bus Signal: -5 to 10V
Physical
• Connectors: DeviceNet Standard “Sealed Micro”
Adapter cable included for DeviceNet
Standard “Sealed Mini”
ORDERING INFORMATION
Engineering No. Standard Order No.
DN-MTR (E)
Product Description
112008-0013
NetMeter for DeviceNet
DN-MTR-KIT (E)
112008-0014
NetMeter Kit for DeviceNet (includes carrying case, PowerMonitor T and LED Termination Resistor)
DN-MTR-BAG
112008-0003
NetMeter carrying case
DN-MTR-CAL
112008-0004
NetMeter ISO calibration
715-0016
112062-0048
NetMeter User Guide, pocket book, 28 pages
*DeviceNet is a registered trademark of Open DeviceNet Vendor Association
42
FEATURES AND BENEFITS
• Predicts power faults by logging outside of specification power conditions thereby increasing uptime
• Helps quickly certify new installations
• Minimizes maintenance repair and
downtime by analyzing bus power
quality
SPECIFICATIONS
Reference Information
• UL File No.: E152210
• CSA File No.: LR6837
Electrical
• Power supply: 7–30V DC, < 50mA
• Basic analog accuracy: ± 100mV
• Minimum “Low” voltage threshold:
<12.96V
• Nominal “OK” voltage range:
12.96V–24.78V
• Maximum “high” voltage threshold:
>24.78V
• Glitch/Ripple threshold (AV/AT):
Var 75 V/S at 16mS to 640 V/S at
1.0mS
• Reset: Magnet at drop “reset”
changes mag reed switch state
Physical
• Connector face:
Thermo plastic elastomer
• Molded body: Thermo plastic elastomer
• Coupling nut: Zinc diecast black e-coat
• Operating temperature:
-20 to +80°C
Environmental
Protection: IP67
NEMA Rating: NEMA 6
DeviceNet*
Brad® Mini-Change®
Diagnostic Power
Monitor2® Tees
4
1
5
4
3
3
130035Male/Female
Thick Media
4
1 - Drain
2 - V+
3 - V-
5
4 - CAN_H
5 - CAN_L
2
1
2
1 - Drain
2 - V+
3 - V-
4 - CAH_H
5 - CAH_L
1 - Drain
2 - V+
3 - V-
5
4
2
3
2
1
4 - CAH_H
5 - CAH_L
4
1 - Drain
2 - V+
3 - V-
5
4 - CAN_H
5 - CAN_L
®
ORDERING INFORMATION
Diagnostic Type
Left Trunk Gender
Right Trunk Gender
Drop Gender
Male
Female
Female
2
2
3
3
4
4
1 - Drain
21--V+
Drain
32--V-V+
3 - V-
Standard
Bus Drop Tee
with
Diagnostics
3
3
12
12
3
3
2
2
1 - Drain
21--V+
Drain
32--V-V+
3 - V-
5 4
3 5 4
3
5 4
4 5
35 4 3 4 5
3
3
5 4
3 5 4
3
5 4
35 4
3
54
54
5
2
2
21
21
1
12
12
54
5
4 1 - Drain
2 4 - CAN_H
21
24 - CAH_H
21
1 41- -CAH_H
41- -CAN_H
Drain
4 - 1CAN_H
- 5Drain
41- -CAH_H
- 12Drain1 - Drain
Drain
4 - 1CAH_H
Drain
4 - 1CAH_H
- 12Drain
5421---CAN_L
-CAN_H
Drain 54--12CAN_L
CAN_H
- Drain
45 - CAN_H
V+
V+ 21--V+
CAN_L
5421---CAH_L
V+ 21--V+
CAH_L
5421---CAH_L
V+
Drain
-CAH_H
Drain 54--12CAH_L
CAH_H
- Drain
Drain
45 - CAH_H
-CAH_H
Drain 54--12CAH_L
CAH_H
- Drain
V+
V+
532---CAN_L
5 -32CAN_L
- V+
V-V+
V- 32--V-V+5 - CAN_L
V- 32--V-V+
V-V+
532---CAH_L
5 -32CAH_L
- V+
5 - CAH_L532---CAH_L
5 -23CAH_L
- V+
V-V+
V3 - V3 - V- 3 - V3 - V3 - V- 3 - V3 - V3 - V-
Female
4
4
4 1
1 2
1 2 3 4 1
3
3
3
5 4
3 5 4
3
5 4
35 4
3
3
3
2 5
2 5
Male
3
3
12
12
4 1
1 2
1 2 3 4 1
3
3
3
5 4
3 5 4
3
Engineering No.
Order No.
DN3020PM-1
130035-0060
DN3020PM-3
130035-0061
5
5
1
1
4 - CAH_H
45 - CAH_H
CAH_L
5 - CAH_L
Female
5 4
35 4
3
54
54
5
4 1
21
2
21
12
12
54
5
4 1 - Drain
21
2 4 - CAN_H
21
1 41- -CAN_H
Drain
4 - 1CAN_H
- 5Drain
41- -CAH_H
Drain
4 - 1CAH_H
- 12Drain1 - Drain
44- CAH_H
41- -CAH_H
Drain
4 - 1CAH_H
- 12Drain
1
Drain
4
CAN_H
2
V+
5
2
CAN_L
V+
5
2
CAN_L
V+
5
CAN_L
1
Drain
4
CAN_H
1
Drain
4
CAN_H
5421---CAH_L
V+
V+
CAH_L
21--V+
V+
- V+
-CAH_H
Drain 54--12CAH_L
CAH_H
- Drain
45 - CAH_H
Drain 5421---CAH_L
-CAH_H
Drain 54--21CAH_L
CAH_H
Drain
5 -32CAN_L
V-V+
V- 32--V-V+5 - CAN_L
- V+
V-V+
V- 32--V-V+
V-V+
- V5 -32CAH_L
- V+
5 - CAH_L532---CAN_L
532---CAH_L
5 -32CAH_L
532---CAH_L
V+
3 - V3 - V- 3 - V3 - V3 - V- 3 - V3 - V3 - V-
5
5
1
1
4 - CAH_H
54 - CAH_L
CAH_H
5 - CAH_L
Diagnostic Tee
Indication
Led Display
Condition
OK
Green
Normal
HI
Red
Overvoltage
LO
Blue
Undervoltage
HI
Flashing Red
Surge within last 24 hours
LO
Flashing Blue
Brown out within last 24 hours
AC
Flashing Yellow
Power glitch within last 24 hours
*DeviceNet is a registered trademark of Open DeviceNet Vendor Association (ODVA)
43
4 - CA
5 - CA
5
3
DeviceNet* Brad Mini-Change
Diagnostic Power Monitor® Tees
®
4
1
3
1 - Drain
2 - V+
3 - V-
5
3
2
1 - Drain
2 - V+
3 - V-
4 - CA
5 - CA
Page Intentionally Left Blank
44
Page Intentionally Left Blank
45
Get customized insights at: www.molex.com/bradautomation.html
Order No. 987650-6032 Rev. 3
Printed in USA/KC/KC/2K/2015.05
©2015 Molex
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement