Demco | SideQuest AC20037 | Specifications | Demco SideQuest AC20037 Specifications

05/12 Rev.10
AC20037
U.S. Patent No. 6,286,870
Page 1
Thank you for purchasing Demco’s SIDEQUEST. We feel you have made a wise choice and hope you
are completely satisfied with your SIDEQUEST. If you have any questions regarding the applications
of certain solutions or chemicals, contact your chemical supplier and follow chemical manufacturer
recommendations as well as all licensing and use restrictions or regulations.
WARNING: To Avoid Personal Injury or Property Damage, Observe
Following Instructions:
Chemicals are dangerous. Know exactly what you’re going to do and what
is going to happen before attempting to work with these products. Improper
selection or use can injure people, animals, plants and soil.
Always wear protective clothing such as coveralls, goggles and gloves when
working with chemicals or sprayer.
Be sure to dispose of all unused chemicals or solutions in a proper and
ecologically sound manner.
GENERAL INFORMATION
1. Unless otherwise specified, high-strength (grade5)
(3 radial-line head markings) hex head bolts are
used throughout assembly of this sprayer.
3. When placing a parts order, refer to this manual for
proper part numbers and place order by PART NO.
and DESCRIPTION.
2. Whenever terms “LEFT” and “RIGHT” are used in
this manual it means from a position behind sprayer
and facing forward.
Table of Contents
General information.............................................................................................................. 2
Warranty Registration..........................................................................................................3-4
Safety Information..............................................................................................................5-12
Safety Sign Locations.......................................................................................................... 7
Bolt Torque.......................................................................................................................... 13
Assembly Instructions......................................................................................................... 14
Parts Breakdown...............................................................................................................15-17
Plumbing Breakdown.......................................................................................................... 16
Optional Jack Stands Breakdown....................................................................................... 18
Optional External Step Parts Breakdown and List.............................................................. 19
Sprayer Checklist................................................................................................................ 20
Page 2
Ag
RV
Rental
Brakes
Marine
Warranty Registration
4010 320th Street • Box 189 • Boyden, Iowa 51234
Toll Free 800-54DEMCO (800-543-3626) • FAX 800-845-6420
www.demco-products.com
m
m
m
m
m
Very
Satisfied
Satisfied
Dissatisfied
Very
Dissatisfied
How satisfied are you with our product?
m
m
m
m
How satisfied are you with the dealership/distributor sales staff?
Dealer/Distributor Name
City
m
m
m
m
How satisfied are you with the company sales staff?
m
m
m
m
How satisfied are you with the delivery?
m
m
m
m
Did you have any contact with a Demco Representative?
If YES, how satisfied were you?
YES
m
NO
m
m
m
I would recommend this product to my family and friends.
YES
NO
Would you purchase again from DEMCO?
YES
NO
Since taking delivery, have you been contacted by the dealer?
YES
NO
Did you have any problems with this DEMCO product?
If YES, are you satisfied with the company’s resolution of your problem?
YES
m
NO
m
m
m
State
Please list the specific source of information prompting this purchase.
After purchasing this product, do you see any needed product improvement?
If yes, what improvement?
What other products would you like to see DEMCO offer?
Comments
Owner’s Name:
City:
Mailing Address:
State:
Zip Code:
Model#:
Serial #:
Purchase Date:
Owner’s Signature:
3
Please return to DEMCO By FAX or tri-folding this form toPage
the backside,
it is pre-addressed.
Postage
Demco
4010 320th Street, Box 189
Boyden, Iowa 51234
Page 4
SAFETY
TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS
MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING
YOUR PERSONAL SAFETY AND SAFETY OF OTHERS. FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.
THIS SYMBOL MEANS
ATTENTION
BECOME ALERT
YOUR SAFETY IS INVOLVED!
warning:
SIGNAL WORDS
Note: use of the following signal words DANGER,
WARNING, and CAUTION with safety messages.
Appropriate signal word for each has been selected
using following guidelines:
DANGER:
Indicates an imminently hazardous situation that,
if not avoided, will result in death or serious injury.
This signal word is to be limited to most extreme
situations typically for machine components which,
for functional purposes, cannot be guarded.
Indicates a potentially hazardous situation that, if
not avoided, could result in death or serious injury,
and includes hazards that are exposed when
guards are removed. It may also be used to alert
against unsafe practices.
caution:
Indicates a potentially hazardous situation that,
if not avoided, may result in minor or moderate
injury. It may also be used to alert against unsafe
practices.
If you have questions not answered in this manual, require additional copies, or if your manual is damaged,
please contact your dealer or Demco P.O. Box 189, 4010 320th Street, Boyden, IA 51234
ph: (712) 725-2311 or (712) 725-2302 Toll Free: 1-800-543-3626 Fax: (712) 725-2380
http://www.demco-products.com
Page 5
SAFETY...you can live with it
Equipment safety guidelines
Every year many accidents occur which could be avoided by a few seconds of thought and
more careful approach to handling equipment. You, the operator, can avoid accidents by
observing precautions in this section. To avoid personal injury, study precautions and insist
those working with you, or you yourself, follow them.
In order to provide a better view, certain illustrations in this manual may show an assembly
with a safety shield removed. However, sprayer should never be operated in this condition.
Keep all shields in place. If shield removal becomes necessary for repairs, replace shield
prior to use.
Replace any caution, warning, danger or instruction safety decal that is not readable or is
missing. Location of such decals is indicated in this booklet.
Do not attempt to operate this sprayer under the influence of alcohol or drugs.
Review safety instructions with all users.
Operator should be a responsible adult. Do not allow persons to operate or
assemble this sprayer until they have developed a thorough understanding
of safety precautions and how it works.
To prevent injury or death, use a tractor equipped with a roll over protective system (ROPS).
Do not paint over, remove, or deface any safety signs or warning decals on your sprayer.
Observe all safety signs and practice instructions on them.
Never exceed limits of sprayer. If its ability to do a job, or to do so safely is in question
don’t try it.
Lighting and marking
It is the responsibility of operator to know lighting and marking requirements of local highway
authorities and to install and maintain equipment to provide compliance with regulations.
Add extra lights when transporting at night or during periods of limited visibility.
Lighting kits are available from your dealer or manufacturer.
Page 6
SAFETY SIGN LOCATIONS
Part# 10328 Red
(on back side of tank)
WARNING
To prevent serious injury or death
•Refer to chemical supplier and manufacturer recommendations and all
licensing restrictions or regulations.
•Always wear recommended protective clothing when working with chemicals or
sprayer.
•Dispose of all unused chemicals or solutions in proper and ecologically
sound manner. Improper use can injure people, animals, plants and soil.
REv 1
Ab21014
AB21014
WARNING
To prevent serious injury or
death.
Do not ride or stand on sprayer
while any part of sprayer is
moving.
Keep riders off at all times.
REv 1
Ab21001
AB21001
WARNING
To prevent serious injury or death
• Store sprayer on hard level surface.
• Store empty.
REV 1
AB21002
Part# 10327 Amber
Page 7
AB21002
Safety sign care
• Keep safety signs clean and legible at all times.
• Replace safety signs that are missing or have become illegible.
• Replacement parts that displayed a safety sign should also display current sign.
• Safety signs are available from your distributor, dealer parts department, or manufacturer.
How to install safety signs:
• Be sure installation area is clean and dry.
• Decide on exact position before you remove backing paper.
• Remove smallest portion of split backing paper.
• Align decal over specified area and carefully press small portion with exposed sticky backing in place.
• Slowly peel back remaining paper and carefully smooth remaining portion of decal into place.
• Small air pockets can be pierced with a pin and smoothed out using piece of decal backing paper.
Tire
safety
• Failure to follow proper procedures when mounting tire on rim can produce an explosion resulting in serious injury or death.
• Do not attempt to mount tire unless you have proper equipment and experience.
• Inflating or servicing tires can be dangerous. Whenever possible, trained personnel should be called to service or mount tires.
• Always order and install tires and wheels with appropriate type and load capacity to
meet or exceed anticipated weight to be placed on sprayer.
Remember
Your best assurance against accidents is a careful and responsible operator. If there is any
portion of this manual or function you do not understand, contact your local authorized dealer
or manufacturer.
Before operation:
• Carefully study and understand this manual.
• Do not wear loose-fitting clothing which may catch in moving parts.
• Always wear protective clothing and substantial shoes.
• It is recommended that suitable hearing and eye protection be worn.
• Operator may come in contact with certain materials which may require specific safety equipment relative to handling of such materials. (Examples: extremely dust, molds, fungus, bulk fertilizers, etc.)
Page 8
• Keep wheel and lug nuts tightened to specified torque.
• Assure that agricultural implement tires are inflated evenly.
• Give sprayer a visual inspection for any loose bolts, worn parts, or cracked welds, and make necessary repairs. Follow maintenance safety instructions included in this manual.
• Be sure there are no tools lying on or in equipment.
• Do not use the sprayer until you are sure that area is clear, especially around children and animals.
• Don’t hurry learning process or take sprayer for granted. Ease into it and become familiar with your new equipment.
• Practice operation of your sprayer and its attachments. Completely familiarize yourself and other operators with its operation before using.
• Use a tractor equipped with Roll Over Protection System (ROPS) and fasten your seat belt prior to starting engine.
• Manufacturer does not recommend usage of tractor with ROPS removed.
• Move tractor wheels to widest recommended settings to increase stability.
• Do not allow anyone to stand between tongue or hitch and towing unit when backing
up to equipment.
During operation
• Beware of bystanders, PARTICULARLY CHILDREN! Always look around to make sure it is safe to start engine of towing unit or move sprayer.This is particularly important with higher noise levels and quiet cabs, as you may not hear people shouting.
• NO PASSENGERS ALLOWED- Do not carry passengers anywhere on or in the tractor or sprayer.
• Keep hands and clothing clear of moving parts.
• Do not clean, lubricate, or adjust your sprayer while it is moving.
• When halting operation, even periodically, set tractor or towing unit brakes, disengage PTO, shut off engine, and remove ignition key.
• Be especially observant of operating area and terrain- watch for holes, rocks, or other hidden hazards. Always inspect area prior to operation.
-
DO NOT operate near edge of drop-offs or banks.
-
DO NOT operate on steep slopes as overturn may result.
-
Operate up and down (not across) intermediate slopes. Avoid sudden starts and stops.
Page 9
• Pick the most level possible route when transporting across fields. Avoid edges of ditches, gullies, and steep hillsides.
• Be extra careful when working on inclines.
• Periodically clear equipment of brush, twigs, or other materials to prevent buildup of dry combustible materials.
• Maneuver tractor or towing unit at safe speeds.
• Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious
injury or death.
• Avoid loose gravel, rocks, and holes; they can be dangerous for equipment operation or movement.
• Allow for sprayer length when making turns.
• Do not walk or work under raised components or attachments unless securely positioned and blocked.
• Keep all bystanders, pets, and livestock clear of work area.
• Operate towing unit from operators seat only.
• Never stand alongside of unit with engine running or attempt to start engine and/or operate machine while standing alongside of unit.
• Never leave running equipment attachments unattended.
• As a precaution, always recheck hardware on equipment following every 100 hours of operation. Correct all problems. Follow maintenance safety procedures.
Following operation
• Following operation, or when unhitching, stop tractor or towing unit, set brakes, disengage PTO and all power drives, shut off engine and remove ignition key.
• Store sprayer in an area away from human activity.
• Do not park sprayer where it will be exposed to livestock for long periods of time. Damage and livestock injury could result.
• Do not permit children to play on or around the stored sprayer.
• Make sure all parked machines are on a hard, level surface and engage all safety devices.
• Wheel chocks may be needed to prevent unit from rolling.
Page 10
Highway and transport operations
•
SAFETY CHAINS: If equipment is going to be transported on a public highway, always
follow state and local regulations regarding safety chains and auxiliary lighting. Be sure to check with local law enforcement agencies for your own particular regulations. If required safety chains should be obtained and installed. Only safety chains (not elastic or nylon/plastic tow straps) should be used to retain connection between towing and towed machines in event of separation of primary attaching system. Use a high strength, appropriately sized hitch pin with a mechanical retainer and attach safety chains. Criss cross chains under tongue and secure to draw bar cage, mounting loops, or bumper frame.
• Adopt safe driving practices:
Keep brake pedals latched together at all times. NEVER USE INDEPENDENT BRAKING WITH SPRAYER IN TOW. LOSS OF CONTROL OR UPSET MAY RESULT.
-
- Always drive at a safe speed relative to local conditions and ensure that your speed is low enough for an emergency stop. Keep speed to a minimum.
- Reduce speed prior to turns to avoid risk of overturning.
- Always keep tractor or towing unit in gear to provide engine braking when going downhill. Do not coast.
- Do not drink and drive!
• Comply with state and local laws governing highway safety and movement of farm machinery on public roads.
• Use approved accessory lighting flags and necessary warning devices to protect operators of other vehicles on highway during transport. Various safety lights and devices are available from your dealer.
• Use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use. Local laws should be checked for all highway lighting and marking requirements.
• When driving tractor and sprayer under 20 mph (40 kph) day or night, use flashing amber warning lights and a slow moving vehicle (SMV) identification emblem.
• Plan your route to avoid heavy traffic.
• Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges, intersections, etc.
• Be observant of bridge load ratings. Do not cross bridges rated lower than gross weight of unit you are operating.
Page 11
• Watch for obstructions overhead and side to side while transporting.
• Always operate equipment in a position to provide maximum visibility at all times. Make allowances for increased length and weight of sprayer when making turns, or stopping.
Performing maintenance
• Good maintenance is your responsibility. Poor maintenance is an invitation to trouble.
• Make sure there is plenty of ventilation. Never operate engine of towing vehicle in a closed building. Exhaust fumes may cause asphyxiation.
• Before working on this machine, stop towing vehicle, set brakes, disengage PTO
and all power drives, shut off engine and remove ignition key.
• Be certain all moving parts and attachments have come to a complete stop before attempting to perform maintenance.
• Always use a safety support and block wheels. Never use a jack to support machine.
• Always use proper tools or equipment for job at hand.
• Use extreme caution when making adjustments.
• Follow torque chart in this manual when tightening bolts and nuts.
• Never use your hands to locate a hydraulic leak on attachments. Use a small piece of cardboard or wood. Hydraulic fluid escaping under pressure can penetrate skin.
• Openings in skin and minor cuts are susceptible to infection from hydraulic fluid.
Without immediate medical treatment, serious infection and reactions can occur.
• When disconnecting hydraulic lines, shut off hydraulic supply and relieve all hydraulic pressure.
• Replace all shields and guards after servicing and before moving.
• After servicing, be sure all tools, parts and service equipment are removed.
• Do not allow grease or oil to build up on any steps or platform.
• When replacing bolts refer to owners manual.
• Refer to bolt torque chart for head identification marking.
•
Where replacement parts are necessary for periodic maintenance and servicing,
genuine factory replacement parts must be used to restore your equipment to original
specifications. Manufacturer will not claim responsibility for use of unapproved parts or accessories and other damages as a result of their use.
• If equipment has been altered in any way from original design, manufacturer does not accept any liability for injury or warranty.
• A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance on this equipment
Page 12
BOLT TORQUE
TORQUE DATA FOR STANDARD NUTS, BOLTS, AND CAPSCREWS.
Tighten all bolts to torques specified in chart unless otherwise noted. Check tightness of bolts
periodically, using bolt chart as guide. Replace hardware with same grade bolt.
NOTE: Unless otherwise specified, high-strength Grade 5 hex bolts are used throughout
assembly of equipment.
Bolt Torque for Standard bolts *
Torque Specifications
GRADE 2GRADE 5GRADE 8
“A” lb-ft (N.m) lb-ft (N.m) lb-ft (N.m)
1/4”
6 (8)
5/16” 10 (13)
3/8” 20 (27)
7/16” 30 (40)
1/2” 45 (60)
9/16” 70 (95)
5/8” 95 (130)
3/4” 165 (225)
7/8” 170 (230)
1”
225 (300)
9
18
30
50
75
115
150
290
420
630
(12)
(25)
(40)
(70)
(100)
(155)
(200)
(390)
(570)
(850)
12 (16)
25 (35)
45 (60)
80 (110)
115 (155)
165 (220)
225 (300)
400 (540)
650 (880)
970 (1310)
Bolt Torque for Metric bolts *
CLASS 8.8CLASS 9.8CLASS 10.9
“A” lb-ft (N.m) lb-ft (N.m) lb-ft (N.m)
9 (13)
10 (14)
13 (17)
Torque figures indicated are valid for 6
7
15 (21)
18 (24)
21 (29)
non-greased or non-oiled threads and
8
23 (31)
25 (34)
31 (42)
heads unless otherwise specified. 10
45 (61)
50 (68)
61 (83)
Therefore, do not grease or oil bolts or 12
78 (106)
88 (118)
106 (144)
capscrews unless otherwise specified 14
125 (169)
140 (189)
170 (230)
in this manual. When using locking
16
194 (263)
216 (293)
263 (357)
elements, increase torque values
18
268 (363)
-- --
364 (493)
20
378
(513)
--
--
515 (689)
by 5%.
22
24
GRADE or CLASS value for bolts
516 (699)
654 (886)
*
and capscrews are identified by their
head markings.
GRADE-2
GRADE-5
GRADE-8
A
Page 13
--
--
--
--
702 (952)
890 (1206)
CLASS 8.8
CLASS 9.8
CLASS 10.9
8.8
9.8
10.9
Assembly Instructions For 10-Bolt Hub
Preparation: Remove any loader brackets from the tractor. The
tractor duals must be set to 120” wheel spacing. Mount base
plate (specific to your tractor model) to the side of the tractor. See
separate instruction found in base plate parts box.
1. With proper hydraulic jack, lift tractor until weight is off dual wheel
but still touching ground. Be sure to secure wheel properly.
Remove all lug bolts on the tractor’s dual as shown in VIEW A.
2. Bolt the Hub Spacer to the tractor’s dual:
• VIEW A - Bolt the Hub Spacer to the tractor’s dual using (10) #33
Hex Hd. Bolts and Tractor’s original washers. Bolt the Hub/Spindle
Assembly to the Hub Spacer using (10) #35 and (10) #16 Wheel
Nuts.
• VIEW B - Bolt the Hub Spacer to the tractor’s dual using (10) #29
D-head Studs and Tractor’s original wheel nuts. Bolt the Hub/
Spindle Assembly to the Hub Spacer using (10) #32 and (10) #4
Lockwashers.
• Torque all bolts to the specifications found in this manual.
34
35
16
10
33
31
VIEW A
3. Before installing tank assemblies onto the Hub/Spindle, determine
which height setting is desirable. Slide the tank assembly over the
spindle
as shown in VIEW
C. Make sure theQTY
arrow on the end of the
ITEM
PART #
DESCRIPTION
spindle
is
always
pointing
up
as
shown.
Slide
the tank assembly
*
9445213
WHEEL 46" X 10A, 10 BOLT
1
WASHER, MACHINE, .75 X 14GA NR(
in 8until there
between the tire and
02534 is a spacing of approximately 2”
10
PLATED)
the
assembly.
12 tank07435
3/4" UNFUse
WHEEL(4)
NUT#15 set screws
10to hold the spindle in
320TH ST. PO BOX 189
13216-35
F/ SIDEQUEST
BOLT
23
1inserts on the outside 4010BOYDEN,
place.
Turn theHUB/SPINDLE
set screws
into the10threaded
IOWA 51234
25
10284
BOLT
.875NF
X
2.00
GR5
HEX
10
of the tube the spindle has been placed in.
26
13258
CAST HUB SPACER 10 BOLT
1
27
13568
BOLT .75NF X 3.00 GR5 HEX ZNC
10
THE DRAWING AND ALL
INFORMATION THERE
ON ARE THE PROPERTY OF
DEMCO
4. Install Extension Arm #26 to the tractor base plate on P. 17. using
(1) #27 Pin and (2) #12 Lynch Pins.
5. Slide the fixed or adjustable tank hanger bracket #23 or #25 onto the
extension arm. Bolt channels #15 or #24 to front of tank assembly.
For tractor’s with adjustable channels #24, bolt to the tube slide
box #25. Install set screws. Torque all bolts to the specifications
found in this manual.
6. Repeat same instructions for the opposite side.
NOTE:
View A, B, & C use parts list on next page.
ITEM
PART #
4
00254
.75"-LOCKWASHER
DESCRIPTION
10
10
07435
3/4" UNF WHEEL NUT
10
WARNING
13024
Bolt, 22mm x 100mm D-head Stud
10
22
13211
16.125 HUB SPACER
23
13216-35
HUB/SPINDLE F/ SIDEQUEST 10 BOLT
24
13217
BOLT, .75 NF X 2.50 HEX HEAD GR. 5
7
9445213
1
1
10
1
BVDP
PK
DATE
09/14/09
DATE
11/17/09
UNLESS OTHERWISE
SPECIFIEDALL DIMENSIONS THIRD ANGLE
PROJECTION
ARE IN INCHES
30
DESCRIPTION
10 BOLT ASSEMBLY
003233RD
DRAWING. NO.
TOLERANCES
.X = .060
.XX = ±.030
.XXX = ±.010
MIN. MACHINE SUFACE 250
BREAK ALL SHARP EDGES
BEND AND DRAFT
±1°
14
SCALE: 1:18
SHEE
32
31
VIEW B Agco only.
DRAWN BY
ENG APPOV.
4010 320TH ST. PO BOX 189
BOYDEN, IOWA 51234
To prevent serious injury or death
THE DRAWING AND ALL
INFORMATION THERE
ON ARE THE PROPERTY OF
DEMCO
On John Deere tractors check hub thickness.
If thickness is greater than 2.31” standard
bolts will fail.
13586 Hex Bolt 22MM-2.50 x 140 MM GR. 10.9
must be used.
REV 0
DRAWN BY
ENG APPOV.
QTY
21
WHEEL 46" X 10A, 10 BOLT
4
29
VIEW C
Page 14
PK
DATE
10/14/08
DATE
11/17/09
UNLESS OTHERWISE
SPECIFIEDALL DIMENSIONS THIRD ANGLE
PROJECTION
ARE IN INCHES
TOLERANCES
.X = .060
.XX = ±.030
.XXX = ±.010
MIN. MACHINE SUFACE 250
BREAK ALL SHARP EDGES
BEND AND DRAFT
±1°
DESCRIPTION
10 BOLT ASSEMBLY
003215RD
DRAWING. NO.
SCALE: 1:18
31
15
AC21005
BVDP
15
SHEE
SIDEQUEST PARTS BREAKDOWN
Ref. Part
No.
No.Qty. Description
1.
00083
8 1/2”-UNC Hex Hd. Nut
2.
00084 14 1/2” Lockwasher
3.
00085 20 1/2” Flatwasher
4.
00254 20 3/4” Lockwasher
5.
00482
8 1/2”-UNC x 1-3/4” Gr.5 Hex Hd. Bolt
6.
00640
8 1/2”-UNC Jam Nut
7.
00967 16 1/2”-UNC x 1-1/4” Gr.5 Hex Hd. Bolt
8.
01253
6 1/2”-UNC x 2” Gr. 5 Hex Head Bolt
9.
01254 14 1/2”-UNC x 1-1/2” Gr.5 Hex Hd. Bolt
10.
-
- Original Tractor Washers
11. 02178 16 1/2”-UNC Nylon Lock Nut
12. 02397
4 Lynch Pin
13. 02592 16 3/8”-UNC Nylon Insert Locknut
14.
-
- Wheel Nuts from Tractor’s Duals
15. 06102 12 Set Screw 1/2” x 1-1/4” Cup Point
16. 07435
- 3/4”-NF Wheel Nut
17. 10214-35 16 Tank Hold Down (350 gal. ONLY)
18. 10215-35 2 Tank Hold Down (500 gal. ONLY)
19. 10245
8 Cable Assembly
20. 10918-35 2 Top Angle Support (500 gal. ONLY)
21. 10923-35 3 Support Crossbar (500 gal. ONLY)
22. 10924-35 12
23. 11442-35 4
24. 13022-35 4
25. 13023-35 4
26. 11644-35 2
- 12001-35 2
27. 11651-95 2
28. 12330-35 2
29. 13024 16
30. 13211
2
31. 13216-35 2
-
13215
-
32. 13217 20
33. 13222 16
-
13586 16
-
13587 16
-
13588 16
34. 13775-35 2
35. 13568 20
Tank Support Tube (500 gal. ONLY)
Hanger Bracket
Drop Channel
Tube Slide Box
Mounting Extension Arm, 30”
Mounting Extension Arm, 36”
Upper Pin
Tank Carrier
Agco Bolt 22mm x 100mm D-Head Stud
10 Bolt Hub Spacer
Spindle/Hub Assembly
Spindle Only
3/4”-NF x 2-1/2” Gr.5 Hex Hd Bolt
Bolt, 22MM-2.50 x 120MM Gr10.9 John Deere, Case IH MX Magnum &
TG New Holland
Bolt, 22MM-2.50 x 140MM Gr 10.9 John Deere Heavy Duty
Bolt, .875-9 x 4.00 Gr 8 Case IH 71, 72 & 89
Bolt, .875NF x 4.00 Gr 8 Ford Genesis
10 Bolt Cast Hub Spacer
3/4”-NF x 3” Gr.5 Hex Head Bolt
NOTE:
Refer to this parts list for parts
shown on pages 14,16-17.
5902 Hub Breakdown
Ref.
No.
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
A
B
C
d
Part
No.Qty. Description
13214 1 Oil Seal
13624 1 Inner Cone Bearing, Timken
13626 1 Inner Cup, Timken
13629 1 Hub, includes Inner/Outer Cups
13627 1 Outer Cup, Timken
13625 1 Outer Cone Bearing, Timken
09532 1 Hub Cap Gasket
07362 1 Hub Cap
04305 4 5/16” x 1/2” Hex Head Bolt
07354 1 3” x 1-21/64” x 3/16” Washer
07353 1 1-1/4”NF Castle Nut
05088 1 3/16” x 2-1/2” Cotter Pin
l
e
f
*Items J,K, and L are shown
for reference only and are not
included in hub assembly.
j
k
g
h
Page 15
i
350 GALLON SIDEQUEST CENTER EXIT PARTS BREAKDOWN
13
19
17
15

16
23
31
35
28
3
34
10
15
2
9
33
1
2
5
26
TANK BREAKDOWN
Ref.
No.
Part
No.Qty.
--. P350WA
--. P350A
--. P500WA
--. P500A
P1. 09941
P2. 10267
P3. BRB1034
P4. FTF100
P5. FTF200
2
2
2
2
1
1
1
1
1
Description
350 gallon Tank Assy (white)
350 gallon Tank Assy (yellow)
500 gallon Tank Assy (white)
500 gallon Tank Assy (yellow)
Agitator Jet
Siphon Tube
1” MPT to 3/4” FPT Reducer Bushing
1” Flanged Tank Fitting
2” Flanged Tank Fitting
* When ordering replacement tanks, please specify if
the tank you need is either a right or left or center and/
or yellow or white.
* Items P1, P2, P3, P4, and P5 included when ordering
the tank assy
NOTE:
Refer to p.15 for replacement part numbers.
p1
p3
p4
p2
p5
NOTE: All units will attach elbow fittings here.
Page 16
500 GALLON SIDEQUEST CENTER EXIT PARTS BREAKDOWN
20
21
2
8
2
22
9
3
22
19
13
18
22
15
28
23
15
3
2
9
16
25
31
1
35
2
5
26
15
11
7
6
34
10
24
33
26
12
NOTE:
Refer to p.15 for replacement part numbers.
27
Page 17
12
OPTIONAL SIDEQUEST JACK STANDS BREAKDOWN
Notes:
Adjustable jack may be used in two locations.
On the outside of the Stand Mount Bracket
as well as in the rear of the Tank holder.
Ref.
No.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Part
No.Qty.
07551-35
10199-35
10243
10244-35
00182
00477
00489
01718-95
02496
02587
04445
00060
00061
00907
4
2
2
2
2
8
4
4
4
4
4
6
6
6
Description
Wheel Stand
Stand Mounting Bracket
Caster Wheel Assembly
Adjustable Jack Assembly
Hair Pin, 7 gauge
5/8” Flatwasher
5/8”-UNC Jam Nut
Lock pin
5/8”-UNC x 4” Hex Hd Bolt Gr.5
5/8”-UNC Nylon Insert Locknut
6” x 2” Black Wheel with bushing
3/8” Lockwasher
3/8”-UNC Hex Hd. Nut
3/8”-UNC x 1” Hex Hd. Bolt Gr.5
14
1
8
2
12
13
5
9
6
11
6
7
10
4
3
Page 18
Optional SideQuest Fold-away External Step PARTS BREAKDOWN
Re
ar
of
Tra
c
tor
4
5
8
7
Fro
nt
of
11
7
6
7
6
8
Tra
c
tor
7
3
9
7
2
8
REF. PART
DESCRIPTION
NO. NO. QTY.
1. 11446-35 2 External Step
2. 11447-35 2 Left Step Support
3. 11448-35 2 Left Step Mount
4. 11449-35 2 Right Step Mount
5. 11450-35 2 Right Step Support
6. 00059 20 3/8” Flatwasher
7. 00523 16 3/8” x 1-1/4” Hex Head Bolt (Gr. 5)
8. 02592 16 3/8” Nylon Insert Locknut
9. 07919-95 8 Bushing
10. 11451 4 Support Cable
11.10219-35 1 Tank Carrier (Not Included w/Kit)
Please order replacement parts by PART NO. and DESCRIPTION.
Page 19
7
8
8
10
Step Parts Breakdown
NOTE: Part quantities are for both sides, but
only one side is shown.
1
6
6
9
3
NOTE: TO ADJUST ANGLE OF STEP
ADJUST THE CABLES TOP BOLT
TO ONE OF 3 HOLE POSITIONS.
10
SPRAYER CHECKLIST:
Downtime caused by field breakdowns is costly and time consuming. Many breakdowns can be
eliminated by periodic equipment maintenance. By spending time reviewing this checklist before
seasonal spraying application time and following proper after season care, you can save time
and money later.
Warning: To Prevent Serious Injury Or Death
• Keep hands, feet, and loose clothing away from rotating parts.
• Wear protective clothing recommended by your chemical and fertilizer manufacturer when working with chemicals.
Check Before Going To The Field :
After Season Care:
1. NOZZLES
Check tip for excessive wear by checking for grooves in
or near tip opening. Check nozzle spacing by starting
at center and working outwards. Check boom for proper
height.
NOTE: It is important to wear proper safety equipment
when cleaning the SIDEQUEST . See your
chemical or fertilizer package for this information.
2. HOSES
Check all hoses for worn or soft spots. Be sure all hose
clamps are tightened and hoses are not kinked or pinched.
Check for leakage in any lines.
3. TANK
Remove and clean agitator orifices. Check orifices for
excessive wear by checking for grooves in or near orifice
opening. Inspect fitting and grommets to insure they are
in good condition.
4. CONTROLS
Check for leakage, plugging, or wear on all valves, fittings,
etc. Clean off any build up of foreign material.
5. PUMP
Check to be sure pump turns freely.
6. FRAME
Be sure all bolts are tightened.
1. After spraying chemicals, run water mixed with cleaners
through tank, pump and all hose hookups. If wettable
powder dries out in the system, it is very difficult to put
back into suspension and can cause malfunction,
damage or injury.
2. When cleaned, tank should have all openings closed
or covered to keep dirt from entering.
3. Pump should be flushed with soluble oil and pump ports
plugged to keep out moisture and air.
4. Disassemble tips and rinse with water or cleaning
solution. (Appropriate for chemical sprayed).
5. Clean tip opening with a wooden toothpick. Never use
wire or hard object that could distort opening.
6. Dispose of all unused chemicals or solutions in a proper
and ecologically sound manner.
6. Water rinse and dry tips before storing.
7. REPLACEMENT PARTS
Replace all worn or damaged parts.
NOTE: DEMCO does not and will not make any
recommendations concerning application of various
chemicals or solutions. These recommendations
relate to either amount or procedure of materials
applied. If you have any questions regarding
application of certain chemicals or solutions,
contact your chemical supplier and follow chemical
manufacturer recommendations.
P.O. BOX 189
4010 320th St., BOYDEN, IA. 51234
PH: (712) 725-2311 FAX: (712) 725-2380
TOLL FREE: 1-800-54DEMCO (1-800-543-3626)
www.demco-products.com
Page 20
Download PDF