ULTIMATE - 30
NN NSTRUCTIÓN MANUAL
Be а ъ
N
™ >.
se
wa Ш
+,
N N |
=
0.25-0.40 cu. in. displacement 2-cycle
0.40 - 0.52 cu. in. displacement 4-cycle
Radio required : 4 channels, 4 servos airplane radio
i Specifications
Wing Span 42.0in/1060 mm
Wing Area 578sqin/37.3sqdm
Flying Weight 4.4-4.61b/2000-2100g
Fuselage Length 39.0in/990 mm
* Specifications are subject to change without notice. *
Warning! This model is not a toy.
Itis designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
Injuries. Remember, safety is the most important thing. Always keep this instruction manual
at hand for quick reference.
THE WORLD MODELS
MANUFACTURING CO.,LTD.
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
www.theworldmodels.com
ULTIMATE - 30
INDEX
BEFORE YOD BEGIN «nenn es oo oi dedi i P. 1
PARTS LIST ay P.2
ASSEMBLY ernennen nennen aa aaa anna P. 3-10
SAFETY PRECAUTIONS ---mmmmmmmmm mmm mmm mmm mmm mmm mmm P. 11
BEFORE YOU BEGIN
ñ Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
manufacturer will replace any defective parts, but will be difficult to extend to the good parts that
are good before gluing to defective parts during assembly.
© Symbols used throughout this instruction manual comprise of the following.
Apply epoxy glue.
Apply epoxy glue. (C.A. glue, super glue.)
Assemble left and right
Ensure smooth non-binding
sides the same way.
movement while assembling.
Peel off shaded portion
Cut off shaded portion.
covering film.
mer Drill holes with the specified
Must be purchased separately!
diameter ( here: 3 mm).
x Warning!
Do not overlook this symbol!
Pay close attention here!
Pierce the shaded portion
covering film.
P.1
Parts List
1.FUSELAGE -- 1 pc.
2.MAIN WING -- 2 pairs
3.MAIN WING BRACE --1set(3pcs)
4. STABILIZER & ELEVATOR -- 1 set
5.VERTICAL FIN & RUDDER -- 1 set
6.CANOPY --1 pc.
7.COWLING -- 1 pc.
8.SPINNER 9 52mm -- 1 pe.
9.ENGINE MOUNT PL5111-030 -- 1 set
10.FUEL TANK 260cc -- 1 set
11.MAIN LANDING GEAR -- 1 pair
12.TAIL LANDING GEAR -- 1 set
13.MAIN WHEEL COVER -- 1 pair
14. MAIN WHEEL @ 50mm -- 2 pcs
15.TAIL WHEEL © 23mm -- 1 pc.
16.PUSHROD:--
WOODEN ROD 2 8 x 280mm | For Rudder Servo ) -- po.
WOODEN RO 8 x 290mm ( For Elevator Servo ) -- 1 pe.
METAL ROD E1.Bx 120mm ( For Elevator & Rudder
Servo ) -- 2pcs
METAL RO 1.8 x 70mm wiThreads ( For Aileron
Servo ) -- 2 pes
METAL RO 1.8 x 165mm w/Threads ( For Aileron
to Aileron mare
METAL RO .8 x 200mm w/Threads ( For Ruder
Servo) -- тре
METAL ROD 01.8 x 180mm w/Threads ( For Ruder
Servo ) -- ype
METAL ROD 01.8 x 185mm w/Threads ( For Elevator
Servo ) -- 1 pc.
17. THROTTLE PUSHWIRE @1.2 x 320mm
w/Plastictube d2 x D3 x 200mm -- 1 set
P.2
18.WOODEN PARTS : --
BALSA 7
X 2mm ( For Aileron Servo ) -- 1 pc.
BALSA то
Ох 2
10x 22 dt For Aileron Servo ) -- 1 pc.
BALSA 10 x 74 mm | For Fixing Fuel Tank ) -- 1 pe.
BALSA 5x 5x 81mm (For Servos Stand ) -- 2 pcs
PLYWOOD 2x40 x72 mm ( Wing Protection] -- À pc.
PLYWOOD 3 x 25 x 40 mm ( Stylobate: Wing to Wing ) -- 4 pcs
EF ops 6 x 20 x 20 mm ( Stylobate: Fuselage to
ng ) -- 1 pc.
PLYWGOD 6 x 24 x 20 mm ( Stylobate: Fuselage to
ng ) -- 1 pc.
PLYWOOD mm --2 pcs
PLYWOOD 6mm -- 1 pe.
PLYWOOD 3 x 66 x 87mm ( Servos Stand ) -- 1 pe.
1
X
x
5
19.PLASTIC PARTS : --
CLEVIS 3 Pes
COLLAR 6mm -- 4 pcs
PLATE -- 5 pcs
RING @2.3mm -- 2 pcs
STRAPER -- 3 pcs
HORN -- 7 sets
PILOT Aa 063A) --1 pc.
SILICON GROMMET d1.5x D6.5mm ( For Canopy &
Cowling ) --9 pcs
20. METAL PARTS: --
LINKAGE CONNECTOR 2.1mm -- 2 sets
COLLAR 2.1mm w/set screw -- 1 set
COLLAR 3.6mm wiset screw -- 2 sets
NUT 3mm -- 8 pcs
NYLON INSERT LOCK NUT 3mm -- 6 pcs
SCREWPA2 x 8mm --4 pcs
SCREWPA3I x 12mm -- 8 pcs
SCREW PM2 x 12mm -- 14 pes
SCREW PM3 x 12mm -- 6 pcs
SCREW PM3 x 20mm -- 4 pes
SCREW PM3 x 25mm -- 4 pes
SCREW PM4 x 30mm -- 1 pc.
SCREW PWA2.3 x 8mm --5 pes
SCREW PWAZ.6 x 12mm -- 4 pcs
WASHER 3mm -- 24 pcs
WASHER 4mm -- 1 pc.
21.FUEL TUBE 9 6 x 5mm : -- 12 pcs
HEAT-SHRINK TUBE @8 x 40mm -- 4 pcs
22.DECALS : --1 set
MainWinEE_ 9 9 CE
Peel off shaded portion
covering film.
Main Wing (Upper) / (1) I
Bottom View, / >» za
Main Wing) Вт,
3 x 25 x 40 mm
Peel off shaded portion
covering film.
—
For Aileron Servo
Main Wing ( Lower)
Top View
y ; Straper |
Aileron Servo) i
fis @- Е
Fuel Tube — YA
6x5
Pushrod Вох орлы pe ||
@1.8 x70 mm | A er
- “A DA
29 5
Balsa
Tx10x22 mm
Balsa
10 x 10 x 22 mm
Clevis
@ stabilizer) Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel tothe main wing as possible.
tabilizer|
я B'
(Main Wing}
—h]] ——]
GJvertical Fin/Rudder)
PA3x 12mm Screw
(sue ——— 2
Imm Set Screw
(mp 1
2.1mm Collar
OB —
—
es 2.1mm Collar
7 3mm Set Screw
— PA3 x 12 mm Tail Wheel © 2.3mm
G Fuel Tank ) Ñ AY |
Install Balsa 10 x 10 x 74 mm
(For fixing fuel tank)
| N
Fuel Tank C.A
|
® Bottom View
(Engine Mount)
PM3 x 20mm Screw ae aan a
\
/ om =
Y EX
= 0 Install Engine position
Engine) i =
| == |
PM 3 x 25mm Screw À Ek
TET — 4 DA
3mm Washer 3mm
© 8 Ee,
“Am,
3mm Nut Ss
a Е
E 4 = | [a Naa
Of 8 Ka. >
ATA MA
Illustration is for side mount.
You can mount your engine
mgt or inverted E by
+ VF Trust anales othe -
m к MH)
tJ o OS os “QI N affected.
N NA
ic ls ee ah
Igy
PM 3 x 25mm 3mm
3mm +
EJ cowling)
PWA 2.6 x 12mm
PWAZ.6 x 12 mm Screw Silicon Grommet
A d1.5 x 6.5mm
4
d1.5x D6.5 mm Silicon Grommet
— 4
7
re
PWA 2.6 x 12mm “fa
P.5
(Landing Gear)
РАЗ х 12 тт Screw
(user ———
PA3 x 12mm
Plate
E ZN ZN ==
| РА2 х 8mm Screw
| (hm 4
3mm Set Screw
3.6mm Collar
OE —
3.6mm Plastic Cllar
Oo
PAZ x 8mm
Plastic Collar 3.6mm Completed
3mm Set Screw
\ 3.6mm Collar
Wheel @ 50mm
(Elservo Set
LINKAGE CONNECTOR
3mm Set Screw
UN — 2
Linkage Connector
рн
2mm Nut
©
2mm Washer
Rudder Pushrod
Throttle Pushrod
Plastic Tube
d1.7 x 200mm
=m included with the Radio Set.
Rudder Servo
Throttle Servo
I Please refer to attached sheet for linkage connector installation.
P.6
(El Rudder Pushrod)
Fuel Tube
Y 6 x5mm
1.8 x 120mm Heat - shrink Tube
— Be careful not to scorch
the heat -shrink tube!
COMPLETED
$1.8 x 270mm
me
=a—+ 01.8x270mm
5mm
@eievator Pushrod)
1.8 x 120mm
Heat - shrink Tube
1.8x 185mm
Clevis
„” —
3 =
a
>
и Fuel Tube
„” @6x5mm
и „— 1.8 x 180mm
PC ES
Be careful notto scorch
the heat - shrink tube!
pe — р
—: > >=— oa
COMPLETED
као Equ ipment) 9 install and arrange the servo as shown in the diagram.
#
к
+
Throttle Rudder Elevator
Servo Servo Servo
Fuel Tube
@ 6x 5mm
Pushrod
®
Throttle Pushwire d1.2 x 320
w / Plastic Tube 2 x 200mm
O Srtaper
Rudder Pushrod
Plywood 3x 66 x 87mm
® Bottom View
P.7
Linkage)
PM2 x 12mm Screw
(rrr
6
4 17 PM2 x 12mm)
I
Elevator
Hom
4a
Rudder
Bottom View
&icanopy)
PWA2.3x8mm Screw
(uo —— ;
D1.5x D6.5mm Silicon Grommet
:
T `
%
`
% %
% %
+
%
a
PWAZ.3x 8mm
7
Q
#
Pa
o 7
%
x NS
al | De Lo Зи a Apply double - sided tape
# бо == =
We vo
CC [TEE
3.5mm,
iran
T $,
*%
PWAZ2.3 x 8mm
P.8
Main Wing)
Pmá x30mm Screw
RT Ц — 1
4mm Washer À
(©) 1 | Pm4 x 30mm
4mm ___4+ Wing Protection
И о | 2x72x40mm Cf
Main Wing
( Lower)
® Bottom View
Main Wing)
Pm3x12mm Screw
PM3 x 12mm
3mm Washer
(О) 12
3mm Nylon Insert Lock Nut
@
Main Wing
BRACE
Fasten the upper and lower wing to the fuselage,
the mark and drill the @ 3mm holes on the cabane
through which the PM3 holding bolts pass through. PM3 x 12mm
P.9
EN) Main Wing)
Main Wing ( Upper)
PM2x 12mm Screw
(ummm 8
Main Wing ( Lower)
PM2 x 12mm ——=—"
f Pushrod w/ Threads
@1.8x 185mm
| Fuel Tube
@6x5mm
PM2 x 12mm TT Clevis
Horn
eX wing Setting)
Rudder
Fa
EEE
TICA
MT
TELLA
À = À
В = В'
C=C
D=D
Е = Е'
F =F'
G=G
H=H
Adjust the wing and fuselage configuration
as in the diagrams.
- ! |
| |
a _ = == ов
Е Е'
G G'
E E'
D D
Eli Control Throws)
Elevator
Rudder
Aileron
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
P.10
EA Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyeris
absolutely necessary.
# Pre - flight adjustment must be done before flying, itis very dangerous to fly a badly
pre - adjusted aircraft.
#ULTIMATE 30 is designed to be powered by 2C 0.25 - 0.40 or 2C 0.40 - 0.52 engine,
using a more powerful engine does not mean better performance. In fact, over powered
engine may cause severe damage and injuries.
#Make sure the air field is spacious, never fly the plane too close 3 to people and never get
too close to arunning propeller.
A0090402
P.11
">
