Agilent Technologies | InfiniiVision 7000 Series | Agilent Technologies 5000, 6000 and 7000 Series InfiniiVision

Agilent Technologies
5000, 6000 and 7000 Series
InfiniiVision Oscilloscope Probes
and Accessories
Selection Guide Data Sheet
To get the most out of your
scope, you need the right
probes and accessories
for your particular
application. That’s why
Agilent Technologies
offers a complete family
of innovative probes
and accessories for the
5000, 6000 and 7000
Series InfiniiVision
oscilloscopes. For the most
up-to-date and complete
information about Agilent’s
accessories, please visit
our web site at:
www.agilent.com/find/
scope_probes
Table of Contents
Probe Compatibility Table ...................................................................... 2
Passive Probes ......................................................................................... 3
High-voltage Passive Probes ................................................................. 4
Active Differential Probes ...................................................................... 5
Active Single-ended Probes ................................................................... 8
Mixed Signal Oscilloscope Logic Probes ........................................... 11
Current Probes ....................................................................................... 13
Wedge Probe Adapters ......................................................................... 15
PC Connectivity ...................................................................................... 16
Agilent IntuiLink Software ................................................................ 16
Miscellaneous Accessories ................................................................. 17
Testmobile ........................................................................................... 17
Carrying Cases .................................................................................... 17
Rackmount Kit ..................................................................................... 17
Warranty Information (Remove All Doubt) .........................Back cover
Contact Agilent.........................................................................Back cover
Probe Compatibility Table
For ordering information when replacing your probe or probe accessory: Refer directly to the page number listed in the
table of contents for your probe model.
To assist you in selecting the proper probe for your application: Use our probe compatibility table below to find the probes
that are recommended for use with your 5000, 6000, and 7000 Series InfiniiVision oscilloscope.
DSO5000A
100 MHz
DSO5000A
300 - 500 MHz
MSO/DSO6000A
100 MHz
MSO/DSO6000A5
MSO/DSO7000A
300 MHz - 1 GHz
N2863A 10:1 300 MHz
(included in 5000 Series
100/300 MHz)
Recommended
Compatible
Compatible
Compatible
10070C 1:1 20 MHz
Recommended
Recommended
Recommended
Recommended
10073C 10:1 500 MHz
(included in 6000 Series 300 MHz 1 GHz and 5000 Series 500 MHz)
Compatible
Recommended
Compatible
Recommended
10074C 10:1 150 MHz
(included in 6000 Series 100 MHz)
Recommended
Compatible
Recommended
Compatible
High-voltage
passive probes
page 4
10076A 4 kV
Recommended
Recommended
Recommended
Recommended
N2771A 30 kV
Recommended
Recommended
Recommended
Recommended
Active
differential
probes
page 5
1130A 1.5 GHz1
Compatible
Recommended
Incompatible
Recommended
Probe type
Probe model
Passive probes
page 3
5
N2772A 20 MHz (use with N2773A)
Recommended
Recommended
Recommended
Recommended
1141A 200 MHz (use with 1142A)
Compatible
Recommended
Compatible
Recommended
Active
single-ended
probes
page 8
1156A 1.5 GHz2
Compatible
Recommended
Incompatible
Recommended
1144A 800 MHz (use with 1142A)
Incompatible
Recommended
Incompatible
Recommended
1145A 750 MHz 2-ch (use with 1142A) Incompatible
Recommended
Incompatible
Recommended
Mixed signal
oscilloscope
logic probes3
page 11
01650-61607 16-channel
Incompatible
Incompatible
Recommended
Recommended
54620-68701 2x8-channel
(included in MSO6000A)
Incompatible
Incompatible
Recommended
Recommended
Current probes
page 13
1146A 100 kHz
Recommended
Recommended
Recommended
Recommended
N2780A 2 MHz (use with N2779A)
Recommended
Recommended
Recommended
Recommended
N2781A 10 MHz (use with N2779A)
Recommended
Recommended
Recommended
Recommended
N2782A 50 MHz (use with N2779A)
Recommended
Recommended
Recommended
Recommended
N2783A 100 MHz (use with N2779A)
Recommended
Recommended
Recommended
Recommended
1147A 50 MHz
Recommended
Recommended
Incompatible
Recommended
1. The 1130A probe amplifier supports both single- and differential-ended measurements. Higher bandwidth InfiniiMax probe model 1131A, 1132A, and
1134A are also supported by 5000, 6000, and 7000 Series 300 MHz - 1 GHz models.
2. The 1157A and 1158A are also supported by all 5000, 6000, and 7000 Series 300 MHz - 1 GHz models.
3. Recommended for MSO6000A, and MSO7000A, MSOs only.
4. These Infiniium active probes are not supported by 5000, 6000, and 7000 Series – 1152A, 1153A, 1154A, 1155A, 1159A, 1168A, and 1169A.
5. MSO/DSO6000A 100-MHz models do not support any Agilent active probes with AutoProbe interface.
2
Passive Probes
• Designed for optimal performance
with your Agilent 5000, 6000, and
7000 Series scope
Probes come with the following
accessories:
• 20 MHz to 500 MHz
• General-purpose retractable hook
tip hooks onto wires and test
points for hands-free probing
Rugged, high-quality probes
at a reasonable price
• Ground bayonet provides short,
flexible ground lead for highfrequency measurements
• 1:1 and 10:1 attenuation
Agilent 10070-family passive probes
are-a great choice if you’re looking
for high quality at a very reasonable
price. These general-purpose probes
are designed specifically to give you
optimal performance with your 5000,
6000 and 7000 Series oscilloscopes.
Ruggedized for general-purpose
measurements, they feature a durable
cable and a solid stainless steel probe
body encased with a hard, fractureresistant plastic. They’re designed
and tested to ensure the probes
operate in the toughest of conditions
The N2863A low-cost passive probe
provides a 10:1 attenuation and
features a high input resistance of
10 MΩ.
• General-purpose alligator clip
ground lead for versatile grounding
• Color tags (2 orange, 2 white,
2-blue and 2-green) to place at
both ends of probe cable to help
you quickly identify probes
Accessories available for
passive probes
5081-7705
Probe-tip-to-BNC (m)
adapter
8710-2063
Dual-lead adapter provides
easy connection from
probe signal and ground
to fine-pitch probing
accessories.
10072A
Fine-pitch probing kit
includes 10 SMT clips and
2 dual-lead adapters.
10075A
0.5 mm IC probing kit.
Contains four 0.5 mm
IC clips and 2 dual-lead
adapters.
Ordering information for Agilent
passive probes
All 10070-family passive probes
include one retractable hook tip,
one ground bayonet, one IC probing
tip, one alligator ground lead and a
compensation screwdriver.
N2863A
10:1 300 MHz passive
probe
10070C
1:1 20 MHz passive probe
10073C
10:1 500 MHz passive
probe
10074C
10:1 150 MHz passive
probe
10072A
Fine-pitch probing kit
10075A
0.5 mm IC probing kit
5081-7705
Probe-tip-to-BNC (m)
adapter
8710-2063
Dual-lead adapter
10074C passive probe
Specifications for Agilent 10070 family passive probes
10070C
10073C
10074C
N2863A
Bandwidth
20 MHz
500 MHz
150 MHz
300 MHz
Risetime (calculated)
< 17.5 ns
< 700 ps
< 2.33 ns
< 1.16 ns
Attenuation ratio
1:1
10:1
10:1
10:1
Input resistance
1 MΩ
2.2 MΩ
10 MΩ
10 MΩ (when terminated into 1 MΩ)
Input capacitance
Approx 70 pF
Approx 12 pF
Approx 15 pF
Approx 12 pF
Maximum input (dc + peak ac)
500 V CAT I
400 V CAT II
500 V CAT I
400 V CAT II
500 V CAT I
400 V CAT II
300 Vrms
Compensation range
None
6 - 15 pF
9 - 17 pF
5 - 30 pF
Probe readout
Yes
Yes
Yes
Yes
Cable length
1.5 m
1.5 m
1.5 m
1.2 m
3
High-voltage Passive Probes
• Ideal for measuring up to 30 kV
• Up to 250 MHz bandwidth
• 100:1 or 1000:1 attenuation
10076A high-voltage probe
The Agilent 10076A 4 kV 100:1
passive probe gives you the voltage
and bandwidth you need for making
high-voltage measurements. Its
compact design makes it easier to
probe today’s small power electronics
components and its rugged
construction means it can withstand
rough handling without breaking.
Specifications for 10076A
Bandwidth
250 MHz (–3dB)
Risetime
(calculated)
< 1.4 ns
Attenuation ratio
100:1
Input resistance
66.7 MΩ (when
terminated into
1-MΩ)
Input capacitance
Approx 3 pF
Maximum input
Compensation
N2771A high-voltage probe
The N2771A is a 1000:1 divider
probe for the measurement of
fast high voltage signals. Up to
30 kV dc + peak ac, 10 kV rms.
The probe’s large size and rugged
construction provides superior
protection. The ground lead is fed
through the body of the probe and
protrudes behind the safety barrier,
keeping the ground connection
away from the high voltage. Typical
applications include PMT’s, motor
drives, high voltage switches,
magnatrons and modern projection
systems.
Ordering information for Agilent
high-voltage probe
10076A
High-voltage probe: includes
one retractable hook tip,
one-ground-bayonet, one
IC probing tip, one-alligator
ground lead and a
compensation screwdriver
N2771A High-voltage probe: includes
alligator ground lead,
1-sharp-probe tip
10077A
Accessory kit for 10076A:
includes one retractable
pincher tip, one ground
lead, one insulation cap,
two measuring pins and two
colored tags
Specifications for N2771A
Bandwidth
50 MHz (–3dB)
Risetime
<7 ns
Attenuation ratio
1000:1
Input resistance
100 MΩ (when
terminated into
1-MΩ)
4000 Vpk
Input
capacitance
1 pF
6-20 pF
Range
Compensation
range
7-25 pF
Probe readout
Yes
Max. voltage
Cable length
1.8 m
15 kV dc, 10 kV rms,
30 kV dc + peak ac
Operating
temperature
0°C to +50°C,
80% RH
Storage
temperature
–20°C to +70°C,
90% RH
Dimensions
2 cm (max width
of probe stem after
handle) x 33 cm
7.5 cm (max probe
widthat probe
handle) x 33 cm
10076A derating curve
10076A passive probe
N2771A high-voltage probe
N2771A derating curve
4
High-frequeny Active Differential Probe
Agilent 1130A InfiniiMax High-performance Active Probe System
• 1.5 GHz InfiniiMax probe system
Specifications
• InfiniiMax probe amplifier supports
both differential- and single-ended
measurements for a more costeffective solution
Operating characteristics
• Unrivaled InfiniiMax probing
accessories support browsing,
solder-in, and socketed use models
at the maximum performance
available
System bandwidth (–3dB)
1130A with MSO/DSO610xA, and MSO/DSO7104A: GHz
Input capacitance
Cm = 0.1 pF Cm is between tips
Cg = 0.34 pF Cg is ground for each tip
Cdiff = 0.27 pF Differential mode capacitance = Cm + Cg/2
Cse = 0.44 pF Single-ended mode capacitance = Cm + Cg
• Compatible with 5000, 6000 and
7000 Series oscilloscopes (except
for 6000 series 100 MHz models)
Input resistance
Differential mode resistance = 50 kΩ ± 1%
Single-ended mode resistance = 25 kΩ ± 1%
Input dynamic range
±2.5 V
Input common mode range
±6.75 V dc to 100 Hz; ±1.25 V > 100 Hz
Maximum signal slew rate
18 V/ns when probing a single-ended signal
30 V/ns when probing a differential signal
DC attenuation
10:1 ± 3% before calibration on oscilloscope
10:1 ± 1% after calibration on oscilloscope
Offset range
± 12.0 V when probing single-ended
The 1.5-GHz 1130A InfiniiMax probe
amplifier is a perfect complement to
the 6000 Series 1-GHz models. Its
1.5-GHz bandwidth, extremely low
input capacitance (0.32-pF), high
common mode rejection and the
patented resistor probe tip technology
provide ultra low loading of the
DUT and superior signal fidelity.
Agilent’s innovative InfiniiMax 1130A
differential probe is the easiest-touse, and highest performance probing
system available for high-speed
digital design, and represent a new
industry standard for accuracy,
flexibility and reliability. Designers
can achieve 1-GHz system bandwidth
in conjunction with 1-GHz 6000 and
7000 Series oscilloscopes even when
manually browsing with the probe
or making hands-off measurements.
Optional solder-in probe heads and
solder-in sockets as well as browser
configuration provide full bandwidth
at the probe tip.
Probe bandwidth (–3dB)
> 1.5 GHz
Rise and fall time
(10% to 90%)
233 psec
Maximum input voltage
30 Vpeak, CAT I
ESD tolerance
>8 kV from 100 pF, 300 Ω HBM
Maximum number of
probes supported by
5000/6000/7000 Series
2
Agilent 1130A InfiniiMax probe offers you the highest performance available for
measuring differential and single-ended signals.
5
High-frequeny Active Differential Probe (continued)
Agilent 1130A InfiniiMax High-Performance Active Probe System
Ordering information for Agilent InfiniiMax 1130A probe and accessories
Probe amplifier
1130A
1.5 GHz InfiniiMax probe amplifier (order one or more probe heads or connectivity kits per amplifier)
Connectivity kits
E2669A
InfiniiMax connectivity kit for differential/single-ended measurements
E2668A
InfiniiMax connectivity kit for single-ended measurements
Individual probe heads
E2675A
InfiniiMax differential browser probe head and accessories
E2676A
InfiniiMax single-ended browser probe head and accessories
E2677A
InfiniiMax differential solder-in probe head and accessories
E2678A
InfiniiMax single-ended/differential socketed probe head and accessories
E2679A
InfiniiMax single-ended socketed probe head and accessories
E2695A
Differential SMA probe head
N5425A/N5426A
12-GHz differential ZIF solder-in probe head and ZIF probe tips
N5451A
InfiniiMax long-wire ZIF probe tips (for use with N5425A ZIF probe head)
N5450A
InfiniiMax extreme temperature extension cable (that allows for probing in environments from –55 to
+150 degrees C)
For more comprehensive information about 1130A InfiniiMax probe amplifier and its accessories, refer to the Agilent Infiniium
Osclloscope Probes, Accessories, and Options data sheet with Agilent literature number 5968-7141EN.
6
Active Differential Probes
• Switchable attenuation
• Measure up to 600 V CAT III and
1000 V CAT II
N2772A 20 MHz differential
probe
Use the Agilent N2772A differential
probe with any of the 5000, 6000,
or 7000 Series oscilloscopes to
safely measure floating circuits with
the oscilloscope grounded. With
20 MHz bandwidth and switchable
attenuation of 20:1 and 200:1, it
provides the versatility for a broad
range of applications including
high-voltage circuits, motor controls,
power supply design, and electronic
high-power converters.
Each probe comes with 2 sharp probe
tips for use on small components and
in tight places, 2 retractable probe
hooks for connecting to smaller wires
and through-hole components, and
2-alligator clips for use with larger
cables.
This probe requires a 9 V battery or
Agilent N2773A power supply.
1141A 200 MHz differential
probe
The 1141A is a 1x FET differential
probe with 200-MHz bandwidth and
a 3000:1 CMRR. The probe has a
high-input resistance and low input
capacitance of 7-pF to minimize
circuit loading. The 1141A must be
used with 1142A probe control and
power module, which controls input
coupling modes dc, dc with variable
offset, and dc reject. Two attenuators,
10x and 100x are provided to expand
the linear differential input range to
±30V. This probe works with any 50-Ω
input oscilloscope including 5000 and
6000 Series.
20 MHz
17.5 ns
20:1 and 200:1
selectable via switch
on probe
High CMRR
80 dB @ 60 Hz,
50 dB @ 1 MHz
Max input
600 V CAT III
voltage to ground 1000 V CAT II
Max differential
1000 VDC or
input voltage
1000 Vrms or
1200 VDC + peak AC
Measure up to 600 V CAT III
4
Max number
of probes
supported by
5000/6000/7000
Series
N2772A 20 MHz differential probe,
supplied with a retractable
hook, sharp probe tips and
alligator clips
N2773A Power supply for N2772A
1141A
200 MHz differential probe
1142A
Probe control and power
module for 1141A
Specifications for 1141A differential
probe
700
Bandwidth
200 MHz
600
Risetime
(calculated)
1.75 ns
500
Attenuation ratio
10:1 and 100:1 with
attenuater
High CMRR
Input impedance
3000:1 at 1-MHz
10:1 at 100-MHz
Between inputs:
1 MΩ, 7 pF
Max input
voltage
200 Vdc + peak ac
(probe alone)
500 Vdc + peak ac
(with attenuator)
Max number
of probes
supported by
5000/6000/7000
Series
4
Specifications for N2772A differential
probe
Bandwidth
Risetime
Attenuation ratio
Ordering information for Agilent
differential probes and power supply
Vrms
• 20 MHz to 1.5 GHz bandwidth
400
300
200
100
0
0.01 0.02 0.05 0.1 0.2 0.5
1 2
MHz
5
Derating of each input for the N2772A
N2772 20 MHz differential probe
1141A 200 MHz differential probe
7
10 20 50 100
High-frequency Active Single-ended Probe
Agilent 1156A High-bandwidth Active Single-ended Voltage
• 1.5 GHz probe bandwidth;
< 233 ps rise/fall time
Key specifications – operating characteristics
Probe bandwidth (–3dB)
> 1.5 GHz
• 100 kΩ, 0.8 pF non-resonant input
impedance
Rise and fall time (10% to 90%)
calculated from tr = 0.35/bandwidth
233 psec
• Small size for easier probing
System bandwidth (–3dB)
1156A with MSO/DSO610xA: 1 GHz
• Compatible with 5000, 6000 and
7000 Series (except for 6000 Series
100 MHz models)
Input capacitance
0.8 pF
Input resistance
100 kΩ ± 1%
Input dynamic range
±2.5 V
DC attenuation
10:1 ± 3% before calibration
10:1 ± 1% after calibration
Offset range
±15.0 V
Offset accuracy
< 3% of setting before calibration
1% of setting after calibration
Maximum input voltage
40 Vpeak, CAT I
The Agilent 1156A is a 1.5-GHz
active probe for use with
Agilent InfiniiVision or Infiniium
oscilloscopes. Its high bandwidth
(1.5-GHz), low input capacitance
(<-0.8-pF) and high input resistance
(100 kΩ) input minimizes ultra low
loading of the DUT, making it ideal
for the companion for the 5000, 6000
or 7000 Series oscilloscopes. When
used with the 5000, 6000 or 7000
Series, the 1156A offers you a full
bandwidth of the scope to the probe
tip, giving you the accurate insight
into your hi-speed device.
Incorporating the most advanced
mechanical and electrical design
technologies, the 1156A provide
smaller, lighter and more rugged
probe tip that enable direct and
easy access to fine pitch ICs and
components. With the 1156A probe,
a damping resistor is placed as close
as possible to the point being probed,
which keeps the input impedance
from resonating low, and it also
allows a flat frequency resonance
across the entire bandwidth of the
probe. The 1156A is designed to
withstand 40-V peak AC input and
> –5-kV of ESD, so it will function
reliably in adverse condition.
ESD tolerance
> 5 kV from 100 pF, 300 Ω HBM
Maximum number of probes supported by
6000 Series
4
Ordering information for Agilent 1156A active probe
1156A
1.5 GHz single-ended active probe
Accessories
E2637A
Precision measurement kit (includes 2 solderable ground sockets with
2 green resistive signal pins)
E2638A
Solderable-tip 5 cm resistive signal leads (10) with ground leads (3)
For more comprehensive information
about 1156A active probe, refer to
the Agilent 1156/57/58A Active
Probes Product Overview with Agilent
literature number 5988-3361EN.
Agilent 1156A active probe with
accessories
8
Active Single-ended Probes
• Up to 800-MHz bandwidth
Specifications for 1144A active probe
• 10:1 attenuation
Bandwidth
≥ 800 MHz
• Compatible with 5000, 6000, and
7000 Series 300-MHz - 1-GHz
oscilloscopes
Risetime
(calculated)
≤ 440 ps
Attenuation ratio
10:1, ±2% (when
connected to an
instrument input of
50 ohm, ±0.5%)
Agilent 1144A active probe
The 1144A features 800-MHz
bandwidth, 1-MΩ input resistance,
2-pF input capacitance, 10:1
attenuation and ±40-Vdc + peak ac
maximum input voltage. An FET at the
input allows a high input resistance
and low input capacitance which
minimizes the loading of the circuit
under test. The output impedance
of the probe is 50-Ω which allows
the probe cable to be extended with
a 50-Ω coaxial cable. To use this
probe with 5000, 6000 or 7000 Series
oscilloscope, the 1142A power supply
is required. The 01144-61604 adapter
can be used with the power supply
to provide power for two channels of
active probing.
Input resistance
1 MΩ, ±5%
Maximum input
voltage
±40 V (dc + peak ac)
Input
capacitance*
2 pF (typical)
Input dynamic
range*
0 to ±7.0 V
4
Maximum
number of probes
supported by
5000/6000/7000
Series
Power
requirements
Weight
Net
Probe body
Shipping
Temperature
Operating
Non-operating
Humidity
Operating
Non-operating
Altitude
Operating
Non-operating
*
dc ±12 V to
±15 V ±5%
(at approximately
75 mA each supply)
Approximately
180 g (6.5 oz)
35 g (~1.25 oz)
Approximately
0.8 kg (1.75 lb)
0 to 55 °C
(32 to 131 °F)
–40 to +70 °C
(–40 to +158 °F)
Up to 95% relative
humidity (noncondensing) at
40 °C (104 °F)
Up to 90% relative
humidity at
65 °C (149 °F)
Up to 4,600 meters
(15,000 ft)
Up to 15,300 meters
(50,000 ft)
Operating characteristics
9
1144A active probe
Active Single-ended Probes (continued)
Agilent 1145A 2-channel active
probe
The two-channel 1145A low-mass
active probe has a probe tip that
weighs less than 1-gram making
it ideal for attaching to find pitch
ICs and probing surface mount
components. The probe combines
high bandwidth (750-MHz), low input
capacitance (2-pF) and high input
resistance (1-MΩ). A versatile set of
accessories are provided and when
used in conjunction with the Wedge
adapter, the 1145A provides a handsfree solution for probing 0.5-mm and
0.65-mm IC packages. To use this
probe with 5000, 6000 or 7000 Series
or oscilloscope, the 1142A power
supply is required.
Specifications for 1145A active probe
Bandwidth
750 MHz
Risetime
(calculated)
470 ps
Attenuation ratio
10:1, ±3%
Input resistance
1 MΩ, ±2%
Maximum input
voltage
±40 Vdc + peak ac
Input
capacitance*
2 pF (typical)
Input dynamic
range*
0 to ±6.0 V
1144A
800 MHz active probe
1145A
2-channel 750 MHz
active probe
1142A
Power supply for 1144A
and 1145A
01144-61604 Splitter cable assy
2
Maximum
number of probes
supported by
5000/6000/7000
Series
1145A active probe
*
Ordering information for Agilent
active probes
Operating characteristics
10
Mixed Signal Oscilloscope Logic Probes
• Compatible with all 40-pin logic
probe
• Flying leads offer flexibility
and convenience
MSO probes offer great value
and performance
These logic probes for the
MSO6000A, MSO7000A, 5462xD, and
5464xD Mixed Signal Oscilloscopes
(MSOs) are the same ones used
with Agilent industry-leading
high-performance logic analyzers.
This means we can offer the best
performance, great value and access
to the industry’s broadest range of
logic probing accessories.
The 54620-68701 2 x 8-signal logic
probe is divided into two sets of eight
channels so you can probe pins that
are far apart and work conveniently
with only one set if that’s all you
require. For optimal signal fidelity,
connect ground at each logic probe,
in addition to taking a common
ground to all eight signals via a
separate ground connector on the
probe pod. This probe is included with
MSO7000A and MSO6000A MSOs.
The 01650-61607 is the 40-pin (F)
to 40-pin (F) logic probe cable for
Agilent's 6000 Series and 54600
Series MSOs. This cable gives the
MSO the standard 40-pin female
input connector that many Agilent
logic analyzers have. With this cable,
a user can connect a wide variety of
logic analyzer probes such as Mictor,
Samtec, and Soft Touch probes.
Specifications for Agilent
01650-61607 logic probe
Input impedance
100 kΩ
Input capacitance
12 pF
01650-61607 logic probe
Specifications for Agilent
54620-68701 logic probe
Input impedance
100 kΩ
Input capacitance
8 pF
54620-68701 logic probe
11
Ordering information for Agilent
logic probes
54620-68701 Logic probe with 2 x 8
flying leads. Includes 20
IC clips and 5 ground
leads
01650-61607 40-pin (F) to 40-pin (F)
logic probe cable
Mixed Signal Oscilloscope Logic Probes (continued)
The 6000 and 7000 Series MSO
digital channels were architected to
be compatible with a wide variety of
probing accessories developed over
20 years for logic analyzers. There’s
a good chance that the logic analyzer
accessories you already own work
with your MSO. With the addition
of an optional 40-pin cable, 0165061607, the MSO accepts numerous
logic analyzer accessories:
• E5346A 34-channel Mictor
connector probe
For logic accessories of greater
channel width than MSO digital
channels (> 16 channels), there are
two use models.
• Route up to sixteen signals to the
probe and don’t use the additional
probe channels.
• Route up to 32 signals to the probe
and measure ½ of them at a time.
Simply plug the 40-pin cable to the
other side of the probe to see the
other ½ of the signals.
• E5385A 34-channel Samtec
connector
• E5383A 16-channel flying lead set
• 01650-63203 16-channel
termination adaptor (also available
as a bundle of both the termination
adapter and the 40-pin cable with
PN 10085-68701)
E5396A 16-channel soft touch
connectorless probe
• E5404A 34-channel soft touch pro
connectorless probe
• E5394A 34-channel soft touch
connectorless probe
• E5396A 16-channel soft touch
connectorless probe
E5346A 34-channel Mictor connector
probe
• Any other accessory that connects
to a logic analyzer via a 40-pin
cable
E5385A 34-channel Samtec connector
probe
12
Current Probes
• Up to 100 MHz bandwidth and
500 Arms current
• Hybrid technology to measure
ac and dc
• Compatible with any 1 MΩ
scope input
Accurate current
measurements without
breaking the circuit
Compatible with any scope or voltage
measuring instruments with BNC
input, the 1146A and N2780A Series
current probes offer accurate and
reliable solutions for measuring dc
and ac currents. The probes use a
hybrid technology that includes a
Hall effect sensor, which senses the
dc current and a current transformer,
which senses the ac current, making
it unnecessary to make an electrical
connection to the circuit.
1147A 50-MHz current probe
with AutoProbe interface
The 1147A is a wide bandwidth,
dc to 50-MHz current probe. The
probe offers flat frequency response
across the entire dc to 50-MHz
bandwidth, low noise (< –2.5-mArms)
and low circuit insertion loss.
The 1147A probe is compatible
with the AutoProbe interface,
which completely configures the
oscilloscope for the probe when
used with the 5000/7000 Series and
300-MHz - 1-GHz 6000 Series scope.
Probe power is provided by the scope,
so there is no need for an external
power supply.
N2780A/81A/82A/83A
2-MHz/10-MHz/50-MHz/
100-MHz current probe
The N2780A Series current probes
are high bandwidth, active current
probes, featuring flat bandwidth, low
noise (< –2.5-mArms) and low circuit
insertion loss. In conjunction with
the power supply (model N2779A),
this probe can be used with any
oscilloscope having a high-impedance
BNC input. The companion power
supply N2779A (3x 12 Vdc output)
lets you connect three N2779As to a
single power supply.
1146A 100 kHz current probe
The 1146A ac/dc current probe
provides accurate display and
measurement of currents from
100 mA to 100 Arms, dc to 100-kHz,
without breaking into the circuit. A
battery level indicator and overload
indicator help ensure proper readings.
It connects directly to the scope
through a 2 m coaxial cable with an
insulated BNC.
1147A 50-MHz current probe with
AutoProbe interface
1146A 100 kHz current probe
N2780A Series current probes with N2779A power supply
13
Current Probes (continued)
Characteristics of the 1146A
current probe
Bandwidth*
dc to 100 kHz (–3 dB)
Current
range*
100 mV/A:100 mA to
10 A peak
10 mV/A:1 to 100 A peak
Output signal 1000 mV peak max
AC current
accuracy*
Range
Accuracy
Range
Accuracy
Range
Accuracy
100 mV/A
(50 mA to 10 A peak)
3% of reading ±50 mA
10 mV/A
(500-mA to 40 A peak)
4% of reading ±50 mA
10 mV/A
(40 A to 100 A peak)
15% max at 100 A
Noise
Range 10 mV/A: 480 µV
Range 100 mV/A: 3 mV
Insertion
impedance
(50/60 Hz) 0.01 Ω
Maximum
working
voltage
600 Vrms max.
Characteristics of the 1147A
current probe
Bandwidth
(–3 dB)
dc to 50 MHz
Risetime
7 ns or less
Maximum
current
(continuous)
15 A peak (ac+dc
components) RMS
Maximum
peak current
30 A peak;
Non-continuous
50 A peak; at pulse
width of 10 µs or less
Output
voltage rate
0.1 V/A
Amplitude
accuracy
±1% rdg, ±1 mV (dc
and 45 to 66 Hz, rated
current)
Noise
Equivalent to 2.5 mArms
or less (for 20 MHz
bandwidth measuring
instrument)
Effect of
external
magnetic
fields
Equivalent to a
maximum of 20 mA (in
a dc to 60 Hz, 400 A/m
magnetic field)
Influence
of adjacent
conductor
< 0.2 mA/A AC
Maximum
rated power
3 VA (with rated
current)
Influence of
conductor
position
0.5% of reading at 1-kHz
in jaw
Rated supply
voltage
dc ±12 V ±1 V
5 mm dia. (0.2” dia.)
Battery
9 V alkaline (NEDA
1604A, IEC 6LR61)
Diameter of
measurable
conductors
Probe
interface
BNC (N2774A)
AutoProbe interface
(1147A)
Cable
lengths
Sensor cable:
Appox. 1.5 m (59.0”)
Power supply cable:
Appox. 1 m (39.4”)
Maximum
number
of probes
supported
2 (1147A)
Green LED when > 6.5-V
Battery life
55 hours typical
Note: Reference conditions 23°C ± 5°C,
20 to 75% relative humidity, dc to 1 kHz,
probe zeroed, 1-minute warmup, batteries
at 9 V + 0.1 V, external magnetic field
<40 A/m, no dc component, no external
current carrying conductor, 1 MΩ/ 100 pF
load, conductor centered in jaw.
dc to 2 MHz (N2780A)
dc to 10 MHz (N2781A)
dc to 50 MHz (N2782A)
dc to 100 MHz (N2783A)
Maximum
current
(continuous)
500 A (N2780A)
150 A (N2781A)
30 A (N2782A/N2783A)
Maximum
peak current
(noncontinuous)
700 A peak (N2780A)
300 A peak (N2781A)
50 A peak
(N2782A/N2783A)
Output
voltage rate
0.01 V/A
(N2780A/N2781A)
0.1 V/A
(N2782A/N2783A)
Amplitude
accuracy
±1.0 % rdg ±500 mA
(N2780A)
±1.0 % rdg ±100 mA
(N2781A)
±1.0 % rdg ±10 mA
(N2782A)
±1.0 % rdg ±10 mA
(N2783A)
Ordering information for Agilent
current probes
1146A
100 kHz current probe
1147A
50 MHz current probe with
AutoProbe interface
N2780A 2 MHz current probe
N2781A 10 MHz current probe
N2782A 50 MHz current probe
Note: The above specifications are
guaranteed at 23 °C ± 3 °C (or 73 °F ± 5 °F)
*
Bandwidth
(–3dB)
Temperature ±2% or less (within a
coefficient
range of 0 °C to 40 °C
for sensitivity or 32 °F to 104 °F)
Maximum
600 Vrms max.
common
mode voltage
Low battery
Characteristics of N2780A Series
current probes
Characteristics marked with asterisks are
specified performance. Others are typical
characteristics.
14
N2783A 100 MHz current probe
N2779A 3-channel power supply for
N2780A/81A/82A/83A
For more information about the
N2780A Series current probes, refer
to the Agilent N2780A Series current
probe data sheet, Agilent literature
number 5989-6432EN.
Wedge Probe Adapters
• Easy connection to surface
mount ICs
IC clip kits
An inexpensive solution for probing
fine-pitch ICs, the 10072A SMT Kit
includes ten IC clips and two duallead adapters that connect the clips
directly to 10070-family probes.
E2613A
• Safe, with no chance of shorting
0.5 mm Wedge probe
adapter, 3-signal, qty 1
E2613B
0.5 mm Wedge probe
adapter, 3-signal, qty 2
E2614A
0.5 mm Wedge probe
adapter, 8-signal, qty 1
The 10075A 0.5-mm IC clip kit is
ideal for connecting to IC’s as fine as
0.5-mm. The clip body allows many
clips to be mounted side-by-side. The
kit includes four 0.5-mm IC clips and
two dual-lead adapters that connect
the IC clips directly to 10070-family
probes.
E2643A
0.5 mm Wedge probe
adapter, 16-signal, qty 1
E2615A
0.65 mm Wedge probe
adapter, 3-signal, qty 1
E2615B
0.65 mm Wedge probe
adapter, 3-signal, qty 2
E2616A
0.65 mm Wedge probe
adapter, 8-signal, qty 1
E2644A
0.65 mm Wedge probe
adapter, 16-signal, qty 1
10072A
SMT kit for 10070 probe
family
10075A
0.5 mm IC clip kit
• Mechanically non-invasive contact
• 3-, 8-, and 16-signal versions
• Supports 0.5 mm and 0.65-mm
TQFP and PQFP packages
Problem-free probing
The Agilent Wedge Probe Adapter
eliminates many of the frustrations
associated with probing surface
mount components. If you’ve ever
accidentally shorted IC pins together,
experienced electrical and/or
mechanical problems with soldering
small wires onto leads, or gotten
frustrated juggling multiple probes
while you’re trying to operate your
scope, the Wedge was designed with
you in mind.
Make the inaccessible
accessible
When you use the Wedge, you don’t
have to worry about shorting IC pins
together on a delicate component
– or worse yet on an irreplaceable
prototype. The Wedge is easy to
insert and it stays put. There’s no
need to solder small wires onto
leads. The Wedge is mechanically
non-invasive, so you won’t damage
the legs of the IC. Instead, you’ll
have easy access to hard-to-reach
components.
Ordering information
Agilent Wedge electrical
characteristics
Operating
voltage
< 40 V dc + peak ac
Operating
current
0.5 A maximum
Capacitance 2 pF typical (all except
between
Agilent-E2643A/44A)
contacts
4.33 pF typical at 1-MHz
(Agilent-E2643A/44A)
Selfinductance
15 nH typical (all except
Agilent-E2643A/44A)
37 nH typical at 1-MHz
(Agilent E2642A/44A)
Cross
coupling
–31 dB typical at 100-MHz
(Agilent-E2643A/44A)
Contact
resistance
< 0.1 Ω
Electrical reliability
The Wedge makes two contact
points with each leg of the IC. This
redundant physical connection
increases the electrical reliability of
the connection. And the Wedge’s low
capacitance and inductance provides
superior performance to many other
alternatives.
15
PC Connectivity
Get scope data into your PC
with Agilent IntuiLink without
programming
Minimum operating system
requirements:
• Windows® 95/98, or Me
• Ideal for documentation
and archiving
• Windows NT® 4.0 (with Service
Pack 4 or greater, obtain at
www.microsoft.com)
• Works in familiar Microsoft® Excel
and Word environments
• Windows 2000
• Windows XP
• Leverage the power of Excel
for data analysis and advanced
graphing
Minimum MS Office application
requirements:
• ActiveX controls provided for more
flexible scope programming
• Microsoft Office 2000 (Word or
Excel) or
• Compatible with 5000, 6000 and
7000 Series
• Microsoft Office XP
To simplify the task of transferring
images and waveform data to your
PC, Agilent IntuiLink software
is offered free for all 5000, 6000
and 7000 Series scopes. IntuiLink
Toolbar provides easy access to the
scope data and images from within
your standard PC applications. You
work in a familiar environment at
all times, using PC applications
such as Microsoft Excel or Word to
analyze, interpret, display, print, and
document the data you get from the
scope. The IntuiLink toolbar makes
it easy, providing a simple way to
download data and screenshots into
a spreadsheet or document. You
can also save the scope settings
and retrieve them later to reproduce
difficult setups like glitch capture and
complex triggering.
• Microsoft Office 2003
IntuiLink Data Capture software
for transferring megabytes of
data to PC
The IntuiLink Data Capture is a
standalone software for downloading
waveform data and screen
image from 5000, 6000 or 7000
Oscilloscopes to the PC via USB,
LAN or GPIB (for 5000 and 6000 only)
interface. It provides the capability
to transfer full deep memory data
out of the scope. The IntuiLink
Toolbar application limits the size
of acquisition data available to a
maximum of 50,000 points regardless
of actual number of acquisition points
on the screen. With the IntuiLink
Data Capture, the amount of points
transferred will be the actual number
of acquisition points currently
displayed or you may select the
number of points to download.
Unlike the IntuiLink Toolbar, it is not
based on Microsoft Excel or Word.
However you may still copy and
paste the data on to the Microsoft
applications for manipulating or
charting the data.
For more information or free
download of the software, visit
www.agilent.com/find/intuilink
Simple transfer of images and data with IntuiLink Toolbar
16
Miscellaneous Accessories
Testmobile
Carrying cases
Rackmount Kit
The sturdy Agilent 1180CZ Testmobile
for use with 6000 Series oscilloscope
makes sharing your scope easy.
Its large wheels make it easy to
roll from place to place. For use
with the Agilent 6000 Series scope,
the 1180CZ Testmobile scope cart
with the N2919A bracket provides
convenient mobility and secure
mounting of your scope.
The Agilent N2760A soft carrying
case and N2917B hard carrying case
make transporting and shipping your
5000 and 6000 Series oscilloscope
safe and simple. A scope and other
accessories fit neatly inside the
padded shell for shipment. For use
with the 7000 Series, order N2733A,
soft carrying case.
The Agilent N2916B Rackmount Kit
positions your 5000 and 6000 Series
scope in the center of the rack. Each
kit includes a custom shelf with
rails, 6 BNC pass-throughs and all
necessary screws. For mounting the
7000 Series in the rack, order N2732A
Specifications for the Agilent
Testmobiles
1180CZ
Total load capacity
59 kg (130 lbs)
Tilt tray
45.7 cm wide x
45.7 cm deep
Specifications for the Agilent
carrying cases
1180CZ
Testmobile (6000 Series)
N2917B for 5000 and 6000 Series
N2919A Bracket for 1180CZ
Testmobile and 6000 Series
scope
Dimensions
(W x H x D)
45 cm x 42 cm x 31 cm
N2917B Hard carrying case (5000 and
6000 Series)
Material
Tough ABS Plastic
N2760A Soft carrying case (5000
Series)
N2760A for 5000 Series only
N2760A Soft carrying case for the
5000 Series
Ordering information
Dimensions
(W x H x D)
39 cm x 27 cm x 22 cm
Material
600 Denier Polyfoam
with Tricot Foam
laminate with interior
pack cloth
N2917B Hard carrying case for the
5000 and 6000 Series
17
N2733A Soft carring case (7000
Series)
N2916B Rackmount Kit (5000 and
6000 Series)
N2732A Rackmount Kit (7000 Series)
N2916B Rackmount Kit for
5000/6000 Series
Miscellaneous Accessories
Probe positioners
Ordering information
• Easy-to-manipulate probe arms for
hands-free browsing
Product number
Description
Quantity
N2784A
1-arm probe positioner
1
• One- or two-articulated arms with
stable high-mass base
N2785A
2-arm probe positioner
1
Includes 3x magnifying glass, arm strap, cable tie, probe rest and manual.
• Quick and stable XY positioning
• Weight stabilization technique
in probe holder keeps constant
pressure at the probing point
• Compatible with most scope
probes
• Applications: Hands-free browsing
for electronic components on PC
board
The N2784A and N2785A probe
positioners provide quick and stable
X-Y positioning for PC boards and
devices that require hands-free
probing.
Unlike other probe positioners that
require multiple adjustments to
lock the probe holder into position,
the N2784A and N2785A need
only the “lift and drop” motion to
put the probe in place. The weight
stabilization technique used in
these probe holders keeps constant
pressure at the probing point so the
probe tip stays in position even when
the target board is bumped.
N2784A one-arm probe positioner
The N2784A and N2785A are
compatible with most Agilent scope
probes including InfiniiMax singleended or differential probe. They are
also compatible with various probes
manufactured by other vendors.
The N2784A comes with a single
positioning arm while the N2785A
comes with two positioning arms.
N2785A Two-arm probe positioner
18
Agilent Technologies Oscilloscopes
Multiple form factors from 20 MHz to >90 GHz | Industry leading specs | Powerful applications
19
www.agilent.com
www.agilent.com/find/probes
Agilent Email Updates
www.agilent.com/find/emailupdates
Get the latest information on the
products and applications you select.
Agilent Direct
www.agilent.com/find/agilentdirect
Quickly choose and use your test
equipment solutions with confidence.
Agilent
Open
www.agilent.com/find/open
Agilent Open simplifies the process
of connecting and programming
test systems to help engineers
design, validate and manufacture
electronic products. Agilent offers
open connectivity for a broad range
of system-ready instruments, open
industry software, PC-standard I/O
and global support, which are
combined to more easily integrate
test system development.
Remove all doubt
Our repair and calibration services
will get your equipment back to you,
performing like new, when promised. You will get full value out of
your Agilent equipment throughout its lifetime. Your equipment
will be serviced by Agilent-trained
technicians using the latest factory
calibration procedures, automated
repair diagnostics and genuine parts.
You will always have the utmost
confidence in your measurements.
For information regarding self
maintenance of this product, please
contact your Agilent office.
Agilent offers a wide range of additional expert test and measurement services for your equipment,
including initial start-up assistance,
onsite education and training, as
well as design, system integration,
and project management.
For more information on repair and
calibration services, go to:
www.agilent.com/find/removealldoubt
www.lxistandard.org
LXI is the LAN-based successor to
GPIB, providing faster, more efficient
connectivity. Agilent is a founding
member of the LXI consortium.
Microsoft, Windows and Windows NT are U.S.
registered trademarks of Microsoft Corporation.
Product specifications and descriptions
in this document subject to change
without notice.
For more information on Agilent
Technologies’ products, applications or
services, please contact your local Agilent
office. The complete list is available at:
www.agilent.com/find/contactus
Americas
Canada
Latin America
United States
(877) 894-4414
305 269 7500
(800) 829-4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Thailand
1 800 629 485
800 810 0189
800 938 693
1 800 112 929
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
1 800 226 008
Europe & Middle East
Austria
01 36027 71571
Belgium
32 (0) 2 404 93 40
Denmark
45 70 13 15 15
Finland
358 (0) 10 855 2100
France
0825 010 700*
*0.125 €/minute
Germany
07031 464 6333
Ireland
1890 924 204
Israel
972-3-9288-504/544
Italy
39 02 92 60 8484
Netherlands
31 (0) 20 547 2111
Spain
34 (91) 631 3300
Sweden
0200-88 22 55
Switzerland
0800 80 53 53
United Kingdom 44 (0) 118 9276201
Other European Countries:
www.agilent.com/find/contactus
Revised: October 6, 2008
© Agilent Technologies, Inc. 2008
Printed in USA, November 13, 2008
5968-8153EN
Download PDF