BLACKHAWK! USB560 Quick start manual
BLACKHAWK! USB560 is a JTAG emulator that allows users to connect their PC or notebook computer to a compatible TI DSP-based target board via USB. It supports Code Composer Studio (CCS) version 2.1 or later and provides a simple and convenient way to debug and program target systems.
With its plug-and-play installation, the BLACKHAWK! USB560 is easy to set up and use. It features a compact and portable design, making it ideal for use in both lab and field environments. The emulator supports a wide range of TI DSPs and provides high-speed emulation capabilities, enabling users to quickly and efficiently debug their code.
Advertisement
Advertisement
4 Code
Composer Studio Setup
CCS V2.1 and later Setup
1. Run CCS Setup.
2. Select the TI XDS560 driver from the available board types that corresponds to the DSP on your target hardware. (i.
e. tixds560C55x.dvr—C55xx XDS560 Emulator).
3. Select “add to system” for this board type, which should display the board properties dialog box.
4. Click “next” on the “Board Name and Data File” tab.
5. On the “Board Properties” tab, change the Emulator Name field from XDS560 0 to BH560USB 0, and click “next”.
6. On the “Processor Configuration” tab add the device(s) for your target board and click “next”.
7. On the “Startup Gel File(s)” tab select the appropriate GEL file for each CPU if applicable and click “finish”.
8. This will place a board into the system configuration window in CCS setup.
9. Save changes and exit.
10. If the USB560 is connected to the hardware and powered,
CCS can be started.
NOTE:
The USB560 interface to Code Composer Studio is specifically designed to meet the TI XDS560 driver (DVR) specification. Therefore, when configuring CCS, you simply specify the same parameters as the TI XDS560 for your target hardware, except for the Emulator Name field. This should be changed to indicate “BH560USB 0”, not “XDS560 0”.
4
Blackhawk
123 Gaither Drive
Mt. Laurel, NJ 08054-1701 www.blackhawk-dsp.com
+1-877-983-4514
Blackhawk is a registered trademark of EWA Technologies, Inc.
USB560-QS-03
QUICK
START
GUIDE
Blackhawk™
USB560
JTAG
Emulator
Installation Requirements
• PC or Notebook computer with at least one free USB v1.1 or v2.0 port.
• Windows® 98, ME, 2000 or XP Operating System
• Texas Instruments Code Composer Studio Version 2.1
†
or later.
• CD-ROM Drive.
Inventory of Items Included
1. Blackhawk USB560 JTAG
Emulator POD.
2. USB 2.0 Compliant Cable.
3. 5 Volt DC power supply.
4. AC power cord.
5. JTAG target cable.
6. Installation CD .
7. Product Registration Card.
8. Quick Start Guide.
Other Items Required
connection conforming to
IEEE 1149.1 Standard.
2. Copy of Code Composer
Studio Version 2.1
† or later.
Important Environmental Considerations
This equipment is designed to be operated under the following environmental conditions:
Temperature between 0°
C –55°C. Relative Humidity of 20% - 70% noncondensing.
Operation of the unit
1. Target Board System—a self- powered board with a TI DSP and compatible JTAG header outside of the above range may affect structual and mechanical integrity and cause permanent damage.
Caution is necessasry to minimize ESD (Electrostactic Discharge) which can damage electronic components. Use in a controlled environment where ESD materials and practices are employed is highly recommended.
†
For CCStudio v2.1 (only), download the XDS560 emulation driver subsystem from the TI web site: https://www-a.ti.com/downloads/sds_support/XDS560Update.html
. These files are included with CCS v2.2 and later.
1
1 Emulation Driver Installation
The USB560 JTAG Emulator shipped with its drivers on
CDROM media that are needed by Windows and Code Composer Studio for operation.
1. Insert the Emulation Driver CD.
2. Follow the installation wizard, and when done, you are ready to install the emulator hardware.
NOTE:
If the installation executable fails to start automatically, run X:\Demoshield\Setup.exe, where [X] is the drive letter for your CDROM drive.
2 Hardware Installation
2
WARNING
Be careful to connect interface cables with the correct orientation. Pin 1 on the interface cable should match Pin 1 on the DSP system connector. The JTAG cable assembly features a "keyed" connector to minimize the chance of error.
1. Place the USB560 JTAG Emulator module in desired location.
2. Connect the 5v DC power plug of the power supply to the
5-volt DC input on the USB560 JTAG Emulator (see figure
1).
3. Attach the USB cable to an available USB port on the PC and to the USB connector on the USB560 JTAG Emulator
(see figure 1).
4. Attach the JTAG cable assembly to the corresponding “D” connector of the USB560 JTAG Emulator (see figure 2).
5. Connect the power supply A/C wall cord to A/C power, which will power the USB560 JTAG Emulator and initiate
Plug and Play installation for the Windows device driver
(see step 3 on USB PnP Installation).
USB PnP Installation 3
Windows 98/ME/2000/XP
1. Make sure the USB560 Emulator is powered.
2. Connect the USB cable to the emulator and to the computer.
3. Follow the Windows “New Hardware” prompts selecting the location where the Blackhawk USB device drivers exist.
These file were installed to your system during the
Emulation Driver Installation—step 1. Typical location for these files is folder:
C:\ti\blackhawk\drivers
, where
<
C:\ti
> is the location selected in step 1.
4. When completed, the Blackhawk Control Panel and Windows Device Manager will show the device. The Blackhawk Control Panel can be activated from its icon, located in the Windows Control Panel Dialog Box.
5. Now follow the Code Composer Studio Setup—Step 4
FIGURE 1—USB & Power Endplate
FIGURE 2—JTAG End Plate
3

Public link updated
The public link to your chat has been updated.
Advertisement