Wachsmuth & Krogmann | TAW-2030 | Specifications | Wachsmuth & Krogmann TAW-2030 Specifications

8 GALLON OIL FREE
AIR COMPRESSOR
Item# 6923-05
Model # TAW-2030
PLEASE READ AND SAVE ALL INSTRUCTIONS TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS TOOL.
TABLE OF CONTENTS
Index
P. 1
Important Safety Instructions
P. 2-5
Electrical Requirements
P. 6
General Safety Rules
P. 7,8
List of Main Parts, Tech. Specifications
P. 9
Contents of Packaging, Installation
P. 10
Operation
P. 11- 13
Maintenance
P. 14
Trouble Shooting
P. 15-17
Service Center
P. 17
Warranty Information
P. 18
Warranty Card
P. 20
1
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS TOOL.
Before working with this air compressor read and understand this instruction
manual and safety instructions carefully.
In case you notice any transport damage, when unpacking the air compressor, you must
not start to work with it! The air compressor has to be checked and repaired by an
authorized service station.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR ELECTROCUTION
Serious injury or death could occur if the air compressor is not properly grounded. Your
air compressor is powered by electricity and may cause electric shock or electrocution if
not used properly.
Electrical shock may occur from electrical cord.
Serious injury or death may occur if electrical repairs are attempted by unqualified
persons.
PREVENTION
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Make sure the air compressor is plugged into a properly grounded outlet which
provides correct voltage (120 V) and adequate fuse protection.
Check power cord for signs of crushing, cutting or heat damage. Replace faulty
cord before use.
Keep all connections dry and off the ground. Do not allow electrical cords to rest
in water or in such a position where water could come in contact with them. Do
not touch plug with wet hands.
Do not pull on the electrical cord to disconnect from the outlet.
Never operate air compressor in wet conditions or outdoors when it is raining.
Never operate air compressor with safety guards/covers removed or damaged.
Any electrical wiring or repairs performed on this air compressor should be done
by Authorized Service Personnel in accordance with national and local electrical
codes.
Before opening any electrical enclosure, always shut off the air compressor,
relieve pressure and unplug the air compressor from the power source. Allow air
compressor to cool down. Never assume the air compressor is safe to work on
just because it is not operating. It could restart at any time!
SAVE THESE INSTRUCTIONS!
2
SAFETY WARNINGS
READ ALL SAFETY WARNINGS BEFORE USING AIR COMPRESSOR!
WARNING: TO REDUCE THE RISK OF EXPLOSION OR FIRE OR BURSTING
ƒ
ƒ
ƒ
ƒ
Serious injury or death may occur from normal electrical sparks in motor and
pressure switch.
Serious injury may occur if any air compressor ventilation openings are
restricted, causing air compressor to overheat and possibly ignite a fire.
Serious injury or death may occur from an air tank explosion if air tanks are not
properly maintained.
Serious injury may occur from an air compressor malfunction or exploding
accessories if incorrect system components, attachments, and accessories are
used.
PREVENTION
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Always operate air compressor in a well ventilated area free of flammable vapors,
combustible dust, gases or other combustible materials.
If spraying flammable material, locate the air compressor at least 20 feet away
from the spray area. (An additional hose may be required.)
Never place objects against or on top of air compressor. Operate air compressor
at least 12 inches away from any wall or obstruction that would restrict proper
ventilation.
Drain air tank daily or after each use to prevent moisture buildup in the air tank.
If air tank develops a leak, replace the air tank immediately. Never repair, weld
or make modifications to the air tank or its attachments.
Never make adjustments to the factory set pressures.
Never exceed manufacturer’s maximum allowable pressure rating of
attachments.
Never use air compressor to inflate small, low pressure objects such as toys.
INTENDED USE
ƒ This compressor is intended to generate compressed air required for the
operation of air tools.
ƒ Any use for food processing or medical purposes is not permitted.
ƒ Explosives, combustibles or gases detrimental to health may not be compressed.
ƒ Do not use compressor in hazardous locations.
ƒ Children are not allowed to operate this compressor and any air tools connected
to it.
For any other use the compressor is not intended. Unintended use, any
change on the compressor or use of not approved air tools may cause
unforeseen damages or injuries.
3
WARNING: TO REDUCE THE RISK TO BREATHING, OF BURNS AND FLYING
OBJECTS
ƒ
ƒ
ƒ
ƒ
Serious injury or death could occur from inhaling compressed air. The air stream
may contain carbon monoxide, toxic vapors or solid particles.
Sprayed materials such as paint, paint solvents, paint remover, insecticides,
weed killers, etc., contain harmful vapors and poisons.
Serious injury could occur from touching exposed metal parts. These areas can
remain hot for some time even after the air compressor is shutdown.
Serious injury can occur from loose debris being propelled at a high speed from
the compressed air stream.
PREVENTION
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Never inhale air from the air compressor either directly or from a breathing
device connected to the air compressor.
Operate air compressor only in a well ventilated area. Follow all safety
instructions provided with the materials you are spraying. Use of a respirator may
be required when working with some materials.
Never allow any part of your body or other materials to make contact with any
exposed metal parts on the air compressor.
Always wear safety glasses to shield the eyes from flying debris.
Never point the air stream at any part of your body, anyone else or animals.
Never leave pressurized air compressor unattended. Shut off air compressor and
relieve pressure before attempting maintenance, attaching tools or accessories.
Always maintain a safe distance from people and animals while operating the air
compressor.
Do not move the air compressor while air tank is under pressure. Do not attempt
to move the air compressor by pulling on the hose.
Additional safety guidelines for compressors
In order to avoid any danger for persons or damage of the compressor, you must stick to
the following safety guidelines. If using the air compressor on a worksite please also
follow the instructions of the employer’s liability insurance association and the
regulations for prevention of accidents, when working with compressors and air-tools.
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Always wear ear protection and safety goggles.
During dust generating jobs, you have to wear a dust mask.
Always wear suitable work clothes. During outdoor work, it is recommended to
wear non slipping shoes.
Never direct connected air tools against any persons or animals.
Be sure that the air tools are really designed for the working pressure of the
compressor or that they are supplied via a pressure regulator.
Pay attention when disconnecting the quick coupler. The compressed air inside
the pressure hose will escape all of a sudden. Please hold the air hose firmly,
when disconnecting from the compressor.
Make sure that all screw connections are adequately tightened at any time.
Do not repair the compressor by yourself! All repairs on compressor and air
tools must be done by authorized and trained service stations.
Risk of Burning! Let the compressor cool down, before doing any maintenance
job.
4
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Do not use the compressor without installed guards.
Please note that the compressor will start automatically, when the pressure falls
to the minimum designated pressure.
Make sure the compressor is switched off and disconnected from the power
supply before starting it.
Check the compressor and the accessories carefully and follow their instructions
for maintenance.
Check the compressor for possible damages before any use. All safety and
protection devices or slightly damaged parts must be inspected for proper
function before any use.
Check to see that all of the moving parts are working properly and are not
jammed.
All parts have to be mounted correctly and have to meet all conditions for proper
operation of the compressor.
All damaged protection parts have to be repaired or replaced by an authorized
service station.
Damaged switches have to be replaced by an authorized service-center.
Do not operate the compressor, in case the switch cannot switch “ON” or “OFF”.
Keep handles dry and free from oil or grease.
SAVE THESE INSTRUCTIONS!
5
Electrical Requirements
General Electrical Connections
DANGER: To reduce the risk of electrocution:
1. Use only identical replacement parts when servicing. Servicing should be
performed by a qualified service technician.
2. Do not use in rain or where floor is wet.
This tool is intended for indoor residential use only.
WARNING: Do not permit fingers to touch the terminals of plug when installing
or removing the plug to or from the outlet.
Grounding Instructions
110-120 Volt, 60Hz. Tool Information
NOTE: The plug supplied on your tool may not fit into the outlet you are planning to
use. Your local electrical code may require slightly different power cord plug connections.
If these differences exist refer to and make the proper adjustments per your local code
before your tool is plugged in and turned on.
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This tool is equipped
with an electric cord having an equipment grounding conductor and a grounding plug, as
shown. The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet
installed by a qualified electrician.
A temporary adapter may not be used with this item.
WARNING: If not properly grounded, this tool can cause an electrical shock,
particularly when used in damp locations, in proximity to plumbing, or
outdoors. If an electrical shock occurs there is the potential of a secondary
hazard, such as your hands hitting the cutting tool.
Wire Sizes
NOTE: Make sure the proper extension cord is used and is in good condition. The use of
any extension cord will cause some loss of power. To keep this to a minimum and to
prevent overheating and motor burnout, use the table as below to determine the
minimum wire size (A.W.G.) extension cord.
Use only 3-wire extension cords which have 3-prong grounding type plugs and 3-pole
receptacles which accept the tools plug.
Extension Cord Length
0-25
25-50
Gauge (A.W.G.)
12
10
6
GENERAL SAFETY RULES
WARNING! Read, understand and save all instructions. Failure to follow all
instructions listed below may result in electric shock, fire or serious personal injury. The
warnings, cautions, and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It must be understood by the operator
that common sense and caution are a factor which cannot be built into this product, but
must be supplied by the operator.
SAVE ALL INSTRUCTIONS!
WORK AREA
1. Keep your work area clean and well organized. Cluttered benches and dark areas
invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the
dust or fumes.
3. Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose concentration.
ELECTRICAL SAFETY
Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat,
oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords
may create a risk of fire.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in
serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing and gloves away from moving parts. Wear protective goggles when
operating the machine. It is recommended to wear protective goggles, gloves, sturdy
non-slipping shoes and an apron.
3. Avoid accidental starting. Be sure switch is in OFF position before connecting to a
power outlet. Carrying tools with your finger on the switch when the switch is ON
invites accidents. Disconnect tool from power outlet before carrying out any work on
the machine.
4. Remove adjusting wrench before turning the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in personal injury
5. Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.
6. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
1. Use clamps or other practical way to secure and support the work piece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to
loss of control.
2. Do not force tool. Use the correct tool for your application. The correct tool will do
the job better and safer at the rate for which it is designed.
7
3. Do not use tool if switch does not turn ON or OFF. Any tool that cannot be controlled
with a switch is dangerous and must be repaired.
4. Place the switch in locked or OFF position before making any adjustments, changing
accessories or storing the tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
5. Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users. They should be kept away from work
area.
6. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools, with sharp cutting edges are less likely to bind and are easier to control.
7. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the tools operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
8. Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
SERVICE
1. Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow instructions in the
maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.
SAVE THESE INSTRUCTIONS!
8
LIST OF MAIN PARTS
Description
1.
2.
3.
4.
5.
6.
pressure tank
drain valve
suction filter
pressure regulator
on-/off-switch
working pressure gauge
7.
8.
9.
10.
11.
12.
TECHNICAL SPECIFICATIONS:
Model Number
Rating Voltage
Power Consumption
Motor speed
Displacement
Tank Volume
Max. Pressure
Protection Class
Degree of Protection
Weight
TAW-2030
120V, 60 Hz
1.5 KW/2HP
3400min
3.9 CFM @ 40psi
3.0 CFM @ 90psi
8 Gallons
115 PSI
F
IP20
60 Lbs
9
tank pressure gauge
pressure hose connectors
handle
motor housing
wheels
safety relieve vale
CONTENTS OF PACKAGING
a.
b.
c.
d.
e.
f.
g.
Air compressor
25’ coiled air hose with female and male quick connector
2 brass quick female connectors
2 wheels
2 wheel bolts
2 lock nuts
2 screw nuts
If any of the above items are missing, please contact our service department at 1-888367-7373 (http://wwwk.wk-usa.com) for replacement.
INSTALLATION
1. Place wheel bolt through wheel.
2. Attach wheel bolt to mounting bracket
3. Slide lock nut on the wheel bolt
4. Screw nut on the wheel bolt
5. Repeat to install second wheel.
10
OPERATION
Before each use
CAUTION: Serious injury or death may occur if electrical sparks from motor and
pressure switch come in contact with flammable vapors, combustible dust,
gases or other combustible materials. When using the air compressor for spray
painting, place the air compressor as far away from the work area as possible.
Use extra air hoses instead of extension cords.
CAUTION: In order to avoid damaging the air compressor, do not incline the
air compressor transversely or longitudinally more than 10°.
Pre-Start Checklist
•
•
•
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Check pressure-hose for damages and replace, if necessary.
Check all screwed connections for tightness and tighten, if necessary.
Check power-cable for damages and have it replaced by service-station, if
necessary.
The compressor must operate only in dry environment.
Place air compressor at least 12 inches away from obstacles that may prevent
proper ventilation.
Place the power-cable in a way that it does not interfere your work and that it is
not damaged.
Before connecting the compressor to the power supply, always check the switch
is in position “OFF”. (see FIG. 1)
Protect the power-cable against heat, oil or sharp edges.
Always switch off the compressor by using the main-switch and do not stop by
unplugging.
After having finished your job, switch the compressor off and disconnect from the
power- supply
Start up (see FIG. 4 on page 12)
1. Check the switch is in the “OFF” Position.
2. Plug the power cord into the grounded outlet.
(see FIG. 1)
FIG. 1
3. Switch the compressor “ON” (pull switch up)
and wait; until the maximum tank pressure is
reached at 115 psi. (The motor will stop
automatically). The tank-pressure is indicated
on the tank pressure gauge.
11
4. Set the pressure regulator to the required
working pressure. (see FIG. 2)
FIG. 2
5. Connect the air-hose to the pressure-hose
connector (8). (see FIG. 3)
6. Connect the air-tool with the air-hose.
7. If you will not start to work immediately,
switch the compressor off and disconnect from
the power-supply.
FIG.3
FIG. 4
CAUTION: The regulated pressure may not exceed the maximum working
pressure of your connected air-tool!
If you notice any unusual noise or vibration, stop the air compressor and
refer to “troubleshooting”
12
Shutdown
1. Switch the compressor “OFF” (press switch down) never stop the air compressor
by unplugging it from the power source. This could result in risk of electrocution.
(see FIG. 1)
2. Drain air from the air tank by releasing air with an attached air tool or by pulling
on the safety relieve vale ring. (see FIG. 5)
3. Allow the air compressor to cool down.
FIG. 5
Storing the compressor
ƒ
ƒ
ƒ
ƒ
Switch off the compressor and disconnect from the power-supply.
Before storing the compressor and the accessories, they have to be free of
compressor air.
Open drain valve at bottom of air tank and drain all water before storing. (see
FIG.6)
The compressor has to be stored in a dry and safe please, so that it is out of
reach of children or other unauthorized person.
FIG. 6
CAUTION: Do not store outdoors or under high humidity. Do not position the
compressor on its side for any reason.
13
MAINTENANCE
CAUTION: Before starting any maintenance or cleaning jobs, the compressor
has to be switched off and disconnected from the power supply!
ƒ
ƒ
ƒ
ƒ
Make sure the compressor accessories and air tools are relieved from pressure.
Be sure that all safety and protection devices are operational after having
finishing maintenance or cleaning jobs.
Take care to remove all service tools from the compressor before starting to work
again.
Other maintenance jobs than described in this manual have to be done by an
authorized service center.
After approx. 30 hours operating time:
ƒ
ƒ
ƒ
Drain pressure tank. Turn drain valve at the bottom of the tank counterclockwise,
until compressed air will escape. Any condensed water will be exhausted at the
same time.
Inspect air filter and air vents. Remove any material that my have gotten stuck in
the are vents.
Clean the exterior of the compressor. Wipe off any dirt or dust that has
accumulated on the air tank and housing.
Every month
ƒ
Check the safety valve for leaks or dirt. If necessary clean or replace.
Every 2 months
ƒ
Clean air filter. First take off the motor housing from the air compressor. This is
done by unscrewing the 2 hex bolts on the top of the housing. Then screw the air
filter off the compressor using a wrench # ½ “. (see FIG. 7 and FIG. 8) Rinse the
air filter in AIR TOOL OIL, than blow out any dust that may still remain and dry
thoroughly. Replace filter in reverse order.
FIG. 8
FIG. 7
14
TROUBLE SHOOTING
Problem
Excessive tank
pressure - safety
valve pops off.
Air leaks at
fittings.
Cause
• Pressure switch does
not shut off motor
when compressor
reaches “cut-out”
pressure.
• Pressure switch
“cut-out” too high.
•
Tube fittings are not
tight enough.
Solution
• Switch the compressor “OFF”
If the unit doesn’t shut off,
unplug compressor.
• Contact an authorized
qualified service center.
•
•
Air leaks at or
inside
check valve.
•
Malfunctioning or
dirty check valve.
•
•
Air leaks at
pressure
switch release
valve.
•
•
Malfunctioning
pressure switch
release valve.
Malfunctioning check
valve.
•
•
•
15
Tighten fittings where air can
be heard escaping. Check
fittings with soapy water
solution. DO NOT OVERTIGHTEN.
Use Teflon tape to improve
fittings of tubes.
A malfunctioning check valve
results in a constant air leak at
the pressure release valve
when there is pressure in the
tank and the compressor is
shut off.
Drain tank then remove and
clean or replace check valve.
DO NOT OVERTIGHTEN.
Remove and replace the
release valve.
Malfunctioning check valve
results in a constant air leak at
the pressure release valve
when there is pressure in the
tank and the compressor is
shut off.
Drain tank then remove and
clean or replace check valve.
DO NOT OVERTIGHTEN.
Air leaks in air
tank or
at air tank welds.
•
Damaged air tank.
•
•
DO NOT DRILL INTO,
WELD OR
OTHERWISE MODIFY
AIR TANK OR IT
WILL WEAKEN. THE
TANK CAN RUPTURE
OR EXPLODE. TANK
MUST BE REPLACED.
Contact an authorized
qualified service
center.
Air leaks between
head and valve
plate.
•
Leaking ring.
•
Torque head screws to
8 ft. lbs. If this does
not stop leak, replace
ring.
Motor will not run
or restart.
•
Tank pressure exceeds
pressure switch “cut-in”
pressure.
Wrong gauge wire or length
of extension cord.
Check valve stuck open.
Loose electrical connections.
Possible malfunctioning
motor or starting capacitor.
Paint spray on internal
motor parts.
Fuse blown, circuit breaker
tripped.
Pressure release valve on
pressure switch has not
unloaded head pressure.
•
Let motor cool off and
overload switch will
automatically reset.
Motor will start
automatically when
tank pressure drops
below “cut-in” pressure
of pressure switch.
Check for proper gauge
wire and cord length.
Remove and clean, or
replace.
Check wiring
connection inside
pressure switch and
terminal box area.
Check fuse box for
blown fuse and
replace, if necessary.
Reset circuit breaker.
Do not use a fuse or
circuit breaker with
higher rating than that
specified for your
particular branch
circuit.
Check for low voltage
conditions and/or
proper extension cord.
Disconnect the other
electrical appliances
from circuit or operate
the compressor on its
own branch circuit.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
16
Air leak from
safety
valve.
•
Possible defect in safety
valve.
•
Operate safety valve
manually by pulling on
ring. If valve still leaks,
it should be replaced.
Knocking Noise.
•
Malfunctioning check valve.
•
Remove and clean, or
replace.
Compressor is not
supplying enough
air to operate
accessories.
•
Prolonged excessive use of
air.
Compressor is not large
enough for air requirement.
Restricted air intake filter.
Hole in hose.
Check valve restricted.
Air leaks.
•
Regulator knob
has continuous air
leak.
Regulator will not
shut off air outlet.
•
Pressure release valve on
pressure switch has not
unloaded head pressure.
Damaged regulator.
•
Decrease amount of air
usage. Check the
accessory air
requirement. If it is
higher than the SCFM
or pressure supplied by
your air compressor,
you need a larger
compressor. Clean or
replace air intake filter.
Do not operate the air
compressor
Replace regulator.
•
•
•
•
•
•
SERVICE CENTER
Repairs
Any repair on your compressor has to be carried out only by an authorized or qualified
service-station!
If you have any question in regards to the operation of this power tool please contact
our service center at:
Wachsmuth & Krogmann, Inc.
Tel: 1-888-367-7373
(Business hours Mon-Fri 9:00am - 4:00pm CT)
Website: http://www.wk-usa.com
ENVIRONMENTAL PROTECTION
If the tool should no longer work at all, please make sure that it is disposed in an
environmentally friendly way, by handing it into a public collection point. Please do not
put it with your household waste.
17
LIMITED WARRANTY
The warranty is void if the defect is due to accidental damage, misuse, abuse,
neglect, improper repair or alteration by unauthorized persons or failure to follow
operation instructions provided with the product. This warranty does not apply to
commercial use.
The warranty is non-transferable and applies only to the original purchase and
does not extend to subsequent owners of the product. Liability under this
warranty is limited to repair, replacement or refund. In no event shall liability
exceed the purchase price paid by the purchaser of the product. Under no
circumstances shall there be liability for any loss, direct, indirect, incidental,
special or consequential damage arising out of in connection with use of this
product. This warranty is valid only in the United States of America. This Warranty
gives you specific legal rights. However you may have other rights that vary from
state to state. Some states do not allow limitation on implied warranties or
exclusion of consequential damages therefore these restrictions may not apply to
you.
In case you find the product to be defective please send it within the warranty
period to our service center. To avoid transport damages please send the product
in the original packaging. In return you will either receive your repaired item, a
new product or a refund. Please fill out the Warranty Card and send it together
with the product and purchase receipt
To arrange pick-up of the defective item please call our service center:
Wachsmuth & Krogmann Inc.
Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am-4:00 pm CT)
Website: http://www.wk-usa.com
123 Sivert Court,
Bensenville,IL 60106,
USA
18
WARRANTY INFORMATION
Thank you for purchasing a top quality KingCraft product. This Oil Free Air
Compressor item #6923-05 was tested and meets our stringent quality
standards. This product is warranted to be free from manufacturing defects in
original materials, including original parts, and workmanship until June 13th,
2006 or 1 year with proof of purchase.
19
WARRANTY CARD
In case you find this product to be defective please send it within the
warranty period to our service center. To avoid transport damages please
send the product in the original packaging. In return you will receive your
repaired item, a new product or a refund. This product is warranted to be
free from manufacturing defects in original materials, including original
parts, and workmanship until June 13th, 2006 or 1 year with proof of
purchase.
Please fill in your details below and send it together with the product and
purchase receipt. Please read the Limited Warranty conditions mentioned
in this instruction manual.
Customer Name
Street
City
State
ZIP Code
Purchase Date
Description of Defect :
To arrange pick-up of the defective item please call our service center:
Wachsmuth & Krogmann Inc.
Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am-4:00 pm CT)
Website: http://www.wk-usa.com
123 Sivert Court,
Bensenville,IL 60106,
USA
20
WARRANTY CARD
PLEASE DETACH THIS SECTION AND RETURN IT WITH YOUR PRODUCT
KingCraft Oil Free Air Compressor, item # 6923-05 , model #
TAW-2030
Download PDF