Bryant | 4-WAY MULTIPOISE TWO-STAGE CONDENSING GAS FURNACE 352AAV | Operating instructions | Bryant 4-WAY MULTIPOISE TWO-STAGE CONDENSING GAS FURNACE 352AAV Operating instructions

352AAV
Deluxe 4--Way Multipoise 2--Stage
Condensing Gas Furnace
Installation, Start--Up, and Operating Instructions
for Sizes 060--120, Series B
Visit www.Bryant.com
ama
NOTE: Read the entire instruction manual before starting
the installation. Please retain these instructions with the furnace
after installation for future reference.
ISO 9001:2000
CERTIFIED
NOTE: This furnace can be installed as a (2-pipe) direct vent
or (1-pipe) non-direct vent condensing gas furnace.
REGISTERED
Special Venting Requirements for Installations in Canada
Consignes spéciales pour l’installation de ventillation au Canada
Installation in Canada must conform to the requirements of CSA
B149 code. Vent systems must be composed of pipe, fittings,
cements, and primers listed to ULC S636. The special vent
fittings and accessory concentric vent termination kits and
accessory external drain trap have been certified to ULC S636 for
use with those IPEX PVC vent components which have been
certified to this standard. In Canada, the primer and cement must
be of the same manufacturer as the vent system -- IPEX System
636, PVC/CPVC Primer, Purple Violet for Flue Gas Venting and
IPEX System 636(1)t, PVC Cement for Flue Gas Venting, rated
Class IIA, 65 deg C. must be used with this venting system -- do
not mix primers and cements from one manufacturer with a vent
system from a different manufacturer. Follow the manufacturer’s
instructions in the use of primer and cement and never use primer
or cement beyond its expiration date.
The safe operation, as defined by ULC S636, of the vent system
is based on following these installation instructions, the vent
system manufacturer’s installation instructions, and proper use of
primer and cement. All fire stop and roof flashing used with this
system must be UL listed material. Acceptability under Canadian
standard CSA B149 is dependent upon full compliance with all
installation instructions. Under this standard, it is recommended
that the vent system be checked once a year by qualified service
personnel.
The authority having jurisdiction (gas inspection authority,
municipal building department, fire department, etc) should be
consulted before installation to determine the need to obtain a
permit.
L’installation faite au Canada doit se conformer aux exigences du
code CSA B149. Ce systême de ventillation doit se composer de
tuyaux, raccords, ciments et apprêts conformes au ULC S636. La
tuyauterie de ventillation des gaz, ses accessoires, le terminal
concentrique mural ainsi que l’ensemble du drain de condensat
extérieur ont été certifiés ULCS 636 pour l’application des
composantes IPEX PVC qui sont certifiées à ce standard. Au
Canada l’apprêt et le ciment doivent être du même manufacturier
que le systême de ventillation -- IPEX Système 636, Apprêt
PVC/CPVC. Mauve Violette pour conduit en évacuation des gaz
et IPEX Système 636(1)t, ciment pour PVC pour conduit en
évacuation des gaz, évalué CLASSE IIA, 65 deg. C. doit ëtre
utilisé avec ce systèeme d’évacuation -- ne pas mélanger l’apprêt
et le ciment d’un manufacturier avec le systême de ventillation
d’un autre manufacturier. Bien suivre les indications du
manufacturier lors de l’utilisation de l’apprêt et du ciment et ne
pas utiliser ceux--ci si la date d’expiration est atteinte.
L’opération sécuritaire, tel que définit par ULC S636, du système
de ventilation est basé sur les instructions d’installation suivantes,
ainsi que l’usage approprié de l’apprêt et ciment. Tout arrët feu et
solin de toit utilisés avec ce système doivent être des matériaux
listés UL. L’acceptation du standard Canadien CSA B419 est
directement relié à l’installation conforme aux instructions ci-haut mentionnées. Le standard Canadien recommande l’
inspection par un personel qualifié et ce, une fois par année.
Les autoritées ayant juridiction (inspecteurs de gas, inspecteurs
en bâtiments, département des incendies, etc) devraient être
consultées avant l’installation afin de déterminer si un permis est
requis.
(1) System 636 is a trademark of IPEX Inc.
1
Required Notice for Massachusetts Installations
352AAV
IMPORTANT
The Commonwealth of Massachusetts requires compliance with regulation 248 CMR as follows:
5.08: Modifications to NFPA--54, Chapter 10
2) Revise 10.8.3 by adding the following additional requirements:
a. For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used
in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where
the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting,
including but not limited to decks and porches, the following requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an
alarm and battery back--up is installed on the floor level where the gas equipment is to be installed. In addition, the
installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is
installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled
equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for
the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery back--up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner
shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty
(30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the
above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a
minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas
fueled heating appliance or equipment. The sign shall read, in print size no less than one--half (1/2) inch in size, ”GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve
the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in
accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
5. EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
(1.) The equipment listed in Chapter 10 entitled ”Equipment Not Required To Be Vented” in the most current edition of
NFPA 54 as adopted by the Board; and
(2.) Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from
the dwelling, building or structure used in whole or in part for residential purposes.
c. MANUFACTURER REQUIREMENTS -- GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the
manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design
or venting system components with the equipment, the instructions provided by the manufacturer for installation
of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
d. MANUFACTURER REQUIREMENTS -- GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When
the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the
parts for venting the flue gases, but identifies “special venting systems”, the following requirements shall be
satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation
instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
e. A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled
equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions
shall remain with the appliance or equipment at the completion of the installation.
For questions regarding these requirements, please contact the Commonwealth of Massachusetts Board of State Examiners of Plumbers
and Gas Fitters, 239 Causeway Street, Boston, MA 02114. 617--727--9952.
2
Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Two-Stage Heating With Single-Stage Thermostat
(Adaptive Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Two-Stage Heating With Two-Stage Thermostat
(Non-Adaptive Heating Mode) . . . . . . . . . . . . . . . . . . . . . .
Cooling Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermidistat Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous Blower Mode . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat Pump Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operate Furnace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Furnace Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Gas Input Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Temperature Rise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjust Blower Off Delay (Heat Mode) . . . . . . . . . . . . . . . .
Set Thermostat Heat Anticipator . . . . . . . . . . . . . . . . . . . . .
Check Safety Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CODES AND STANDARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Combustion and Ventilation Air . . . . . . . . . . . . . . . . . . . . . . . . 7
Duct Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Acoustical Lining and Fibrous Glass Duct . . . . . . . . . . . . . . . . 7
Gas Piping and Gas Pipe Pressure Testing . . . . . . . . . . . . . . . . 7
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS . . . 8
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Upflow Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Downflow Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Horizontal Left (Supply-Air Discharge) Applications . . . . . . 12
Horizontal Right (Supply-Air Discharge) Applications . . . . . 13
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Furnace Location Relative to Cooling Equipment . . . . . . . . . 17
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Furnace Location and Application . . . . . . . . . . . . . . . . . . . . . 17
AIR FOR COMBUSTION AND VENTILATION . . . . . . . . . . 18
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Leveling Legs (If Desired) . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installation in Upflow and Downflow Applications . . . . . . . 21
Installation in Horizontal Applications . . . . . . . . . . . . . . . . . 21
Air Ducts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
General Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Ductwork Acoustical Treatment . . . . . . . . . . . . . . . . . . . . . 23
Supply Air Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Return Air Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Filter Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Bottom Closure Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
115-v Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
24-v Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Removal of Existing Furnaces from
Common Vent Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Combustion Air and Vent Pipe Systems . . . . . . . . . . . . . . . . . 30
Condensate Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Condensation Drain Protection . . . . . . . . . . . . . . . . . . . . . . 46
START-UP, ADJUSTMENTS, AND SAFETY CHECK . . . . . 46
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Prime Condensate Trap With Water . . . . . . . . . . . . . . . . . . . . 47
Purge Gas Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
47
48
48
49
49
53
53
53
54
54
54
59
60
60
60
61
AIRFLOW
UPFLOW
HORIZONTAL
LEFT
HORIZONTAL
RIGHT
DOWNFLOW
AIRFLOW
AIRFLOW
AIRFLOW
A93041
Fig. 1 -- Multipoise Orientations
SAFETY CONSIDERATIONS
!
WARNING
FIRE, EXPLOSION, ELECTRICAL SHOCK, AND
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in dangerous
operation, serious injury, death, or property damage.
Improper installation, adjustment, alteration, service,
maintenance, or use could cause carbon monoxide
poisoning, explosion, fire, electrical shock, or other
conditions which may cause personal injury or property
damage. Consult a qualified service agency, local gas
supplier, or your distributor or branch for information or
assistance. The qualified service agency must use only
factory--authorized and listed kits or accessories when
modifying this product.
3
352AAV
TABLE OF CONTENTS
!
This furnace is CSA (formerly AGA and CGA) design-certified
for natural and propane gases (see furnace rating plate) and for
installation in alcoves, attics, basements, closets, utility rooms,
crawlspaces, and garages. This furnace is factory-shipped for use
with natural gas. A CSA listed gas conversion kit is required to
convert furnace for use with propane gas.
See Fig. 3 for required clearances to combustibles.
This furnace SHALL NOT be installed directly on carpeting, tile,
or any other combustible material other than wood flooring. For
downflow installations, a factory accessory floor base must be
used when installed on combustible materials and wood flooring.
Special base is not required when this furnace is installed on the
manufacturer’s coil assembly or when the manufacturer’s coil
box is used. The design of the 352AAV furnace is not CSA
certified for installation in mobile homes, recreational vehicles, or
outdoors. This furnace is suitable for installation in a structure
built on site or a manufactured building completed at final site.
This furnace is designed for continuous return-air minimum
temperature of 60°F (16°C) db or intermittent operation down to
55°F (13°C)db such as when used with a night setback
thermostat. Return-air temperature must not exceed 80°F (27°C)
db. Failure to follow these return air limits may affect reliability
of heat exchangers, motors and controls. (See Fig. 4.)
This furnace is shipped with the drain and pressure tubes
connected for UPFLOW applications. Minor modifications are
required when used in DOWNFLOW, HORIZONTAL RIGHT,
or HORIZONTAL LEFT (supply-air discharge direction)
applications as shown in Fig. 1. See details in Applications
section.
Install this furnace only in a location and position as specified in
LOCATION and INSTALLATION sections of these instructions.
Always provide adequate combustion and ventilation air as
specified in section Combustion Air and Vent Pipe Systems of
these instructions to furnace.
Combustion products must be discharged outdoors. Connect this
furnace to an approved vent system only, as specified in the
Combustion Air and Vent Piping sections of these instructions.
Never test for gas leaks with an open flame. Use a commercially
available soap solution made specifically for the detection of
leaks to check all connections, as specified in the GAS PIPING
section of these instructions.
Always install furnace to operate within the furnace’s intended
rise range with a duct system which has an external static
pressure within the allowable range, as specified in the SET
TEMPERATURE RISE section of these instructions and furnace
rating plate.
When a furnace is installed so that supply ducts carry air
circulated by the furnace to areas outside the space containing the
furnace, the return air shall also be handled by duct(s) sealed to
the furnace casing and terminating outside the space containing
the furnace.
A gas-fired furnace for installation in a residential garage must be
installed as specified in the Hazardous Locations section of these
instructions.
The furnace may be used for construction heat provided that the
furnace installation and operation complies with:
S The furnace is permanently installed with all electrical wiring,
piping, air filters, venting and ducting installed according to
these installation instructions. A return air duct is provided,
sealed to the furnace casing, and terminated outside the space
containing the furnace. This prevents a negative pressure
condition as created by the circulating air blower, causing a
flame rollout and/or drawing combustion products into the
structure.
S The furnace is controlled by a thermostat. It may not be “hot
wired” to provide heat continuously to the structure without
thermostatic control.
CAUTION
FURNACE RELIABILITY HAZARD
Improper installation or misapplication of furnace may
require excessive servicing or cause premature component
failure.
352AAV
Application of this furnace should be indoors with special
attention given to vent sizing and material, gas input rate,
air temperature rise, unit leveling, and unit sizing.
Improper
installation,
adjustment,
alteration,
service,
maintenance, or use can cause explosion, fire, electrical shock, or
other conditions which may cause death, personal injury, or
property damage. Consult a qualified installer, service agency, or
your distributor or branch for information or assistance. The
qualified installer or agency must use factory--authorized kits or
accessories when modifying this product. Refer to the individual
instructions packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing,
and work gloves. Have a fire extinguisher available. Read these
instructions thoroughly and follow all warnings or cautions
include in literature and attached to the unit. Consult local
building codes, the current editions of the National Fuel Gas
Code (NFGC) NFPA 54/ANSI Z223.1 and the National Electrical
Code (NEC) NFPA 70.
In Canada, refer to the current editions of the National Standards
of Canada CAN/CSA--B149.1 and .2 Natural Gas and Propane
Installation Codes, and Canadian Electrical Code CSA C22.1
Recognize safety information. This is the safety--alert symbol .
When you see this symbol on the unit and in instructions or
manuals, be alert to the potential for personal injury.
Understand the signal words DANGER, WARNING, and
CAUTION. These words are used with the safety--alert symbol.
DANGER identifies the most serious hazards which will result in
severe personal injury or death. WARNING signifies hazards
which could result in personal injury or death. CAUTION is
used to identify unsafe practices which may result in minor
personal injury or product and property damage. NOTE is used
to highlight suggestions which will result in enhanced
installation, reliability, or operation.
!
CAUTION
ENVIRONMENTAL HAZARD
Failure to follow this caution may result in environmental
pollution.
Remove and recycle all components or materials (i.e., oil,
refrigerant, control boards, etc.) before unit final disposal.
!
CAUTION
CUT HAZARD
Failure to follow this caution may result in personal injury.
Sheet metal parts may have sharp edges or burrs. Use care
and wear appropriate protective clothing, safety glasses
and gloves when handling parts and servicing furnaces.
The model 352AAV, 2-Stage, 4-way Multipoise, Gas-Fired,
Category IV, condensing furnace is available in model sizes
ranging in high-stage gas input rates of 60,000 to 120,000 Btuh.
4
CODES AND STANDARDS
S Clean outside air is provided for combustion. This is to
minimize the corrosive effects of adhesives, sealers and other
construction materials. It also prevents the entrainment of
drywall dust into combustion air, which can cause fouling and
plugging of furnace components.
S The temperature of the return air to the furnace is maintained
between 55°F (13°C) and 80°F (27°C), with no evening
setback or shutdown. The use of the furnace while the structure
is under construction is deemed to be intermittent operation per
our installation instructions.
S The air temperature rise is within the rated rise range on the
furnace rating plate, and the firing rate has been set to the
nameplate value.
S The filters used to clean the circulating air during the
construction process must be either changed or thoroughly
cleaned prior to occupancy.
S The furnace, ductwork and filters are cleaned as necessary to
remove drywall dust and construction debris from all HVAC
system components after construction is completed.
This furnace is shipped with the following materials to assist in
proper furnace installation. These materials are shipped in the
main blower compartment.
Follow all national and local codes and standards in addition
to these instructions. The installation must comply with
regulations of the serving gas supplier, local building, heating,
plumbing, and other codes. In absence of local codes, the
installation must comply with the national codes listed below and
all authorities having jurisdiction.
In the United States and Canada, follow all codes and standards
for the following:
Step 1 -- Safety
Step 2 -- General Installation
S US: NFGC and the NFPA 90B. For copies, contact the
National Fire Protection Association Inc., Batterymarch Park,
Quincy, MA 02269; or for only the NFGC contact the
American Gas Association, 400 N. Capitol, N.W., Washington
DC 20001
S A manufactured (Mobile) home installation must conform with
the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280, or when this standard is not
applicable, the Standard for Manufactured Home Installation
(Manufactured Home Sites, Communities, and Set-Ups),
ANSI/NCS A225.1, and/or CAN/CSA--Z240, MH Series
Mobile Homes
S CANADA: NSCNGPIC. For a copy, contact Standard Sales,
CSA International, 178 Rexdale Boulevard, Etobicoke
(Toronto), Ontario, M9W 1R3, Canada.
Installer Packet includes:
Installation, Startup, and Operating Instructions
Service and Maintenance Instructions
User’s Information Manual
Warranty Certificate
Loose Parts Bag includes:
Quantity
Pressure tube extension
1
Collector Box or condensate trap extension tube
1
Inducer housing drain tube
1
1/2-in CPVC street elbow
2
Drain tube coupling
1
Drain tube coupling grommet
1
Condensate trap hole filler plug
3
Vent and combustion-air intake hole filler plug
2
Combustion-air intake pipe perforated disk assembly
1
Gas line grommet
1
Vent pipe grommet
1
Combustion-air pipe grommet
1
Power entry hole filler plug
2
Vent Pipe Extension
1*
*ONLY supplied with some furnaces.
The furnace shall be installed so that the electrical components
are protected from water.
For accessory installation detail, refer to the accessory installation
instruction.
NOTE: Remove all shipping materials before operating furnace.
5
352AAV
S US: National Fuel Gas Code (NFGC) NFPA 54--2006/ANSI
Z223.1--2006 and the Installation Standards, Warm Air Heating
and Air Conditioning Systems ANSI/NFPA 90B
S CANADA: National Standard of Canada, Natural Gas and
Propane Installation Code (NSCNGPIC) CSA B149.1--05
26 15⁄16"
(684mm)
26 1⁄4"
(667mm)
1
24 ⁄2"
(666mm)
22 5⁄16"
(567mm)
2-IN. COMBUSTIONAIR CONN
(51mm)
⁄2-IN. DIA
GAS CONN
(13mm)
1
2-IN. VENT CONN
(51mm)
⁄2-IN. DIA THERMOSTAT
ENTRY
(13mm)
22 11 ⁄16"
(576mm)
1
352AAV
14 1⁄2"
TYP
(368mm)
11⁄4" (32mm)
1"
(25mm)
SIDE INLET
28 1⁄2" (724mm)
26 15⁄16" (694mm)
AIRFLOW
26 1⁄4" (667mm)
⁄16"
(21mm)
13
CONDENSATE DRAIN
TRAP LOCATION
(DOWNFLOW &
HORIZONTAL LEFT)
9
⁄16"
(21mm)
13
D
OUTLET
19" (483mm)
5
2-IN. COMBUSTIONAIR CONN
⁄2-IN. DIA
GAS CONN
1
5
⁄16"
(8mm)
1
⁄2-IN. DIA
THERMOSTAT ENTRY
30 1⁄2"
(775mm)
39 7⁄8"
(1013mm)
2-IN. VENT CONN
22 11 ⁄16"
18 1⁄4"
(464mm)
11
⁄16"
(17mm)
11
⁄16"
(17mm)
E
26 ⁄16" TYP (684mm)
CONDENSATE
DRAIN LOCATION
(UPFLOW)
DIMPLE LOCATORS
FOR HORIZONTAL
HANGING
15
SIDE INLET
1"
(25mm)
22 1⁄4" TYP
(565mm)
24 3⁄16"
BOTTOM INLET
(614mm)
⁄16" (11mm)
7
11
A05070
NOTES: 1. Minimum return-air openings at furnace, based on metal duct. If flex duct is used,
see flex duct manufacturer‘s recommendation for equivalent diameters.
2. Minimum return-air opening at furnace:
a. For 800 CFM 16-in . (406mm) round or 14 1/ 2 (368mm) x 12-in. (305mm) rectangle.
b. For 1200 CFM 20-in . (508mm) round or 14 1/ 2 (368mm) x 19 1/ 2-in. (495mm) rectangle.
c. For 1600 CFM 22-in .(559mm) round or 14 1/ 2 (368mm) x 23 1/ 4-in.(591mm) rectangle.
d. For airflow requirements above 1800 CFM, see Air Delivery table in Product Data
literature for specific use of single side inlets. The use of both side inlets, a
combination of 1 side and the bottom, or the bottom only will ensure adequate
return air openings for airflow requirements above 1800 CFM at 0.5“ W.C. ESP.
Dimensions --- IN. (mm)
UNIT SIZE
060 --- 12 / 036060
080 --- 12 / 036080
080 --- 16 / 048080
100 --- 16 / 048100
100 --- 20 / 060100
120 --- 20 / 060120
⁄16" (21mm)
⁄8" (16mm)
13
7
⁄8-IN. DIA
POWER CONN
33 1⁄4"
TYP
30 13⁄16"
(845mm)
(783mm)
7
29 11 ⁄16"
⁄8-IN. DIA (22mm)
TYP
ACCESSORY
(754mm)
POWER ENTRY
32 5⁄8"
27 5⁄8"
TYP
(702mm)
CONDENSATE
(829mm)
DRAIN TRAP
27 9⁄16"
LOCATION
TYP
(ALTERNATE
(700mm)
UPFLOW)
24 1⁄2"
(622mm)
17 5⁄16"
9 7⁄16"
(440mm)
TYP
(240mm)
CONDENSATE
DRAIN LOCATION
(UPFLOW)
22 5⁄16" (567mm)
OUTLET
CONDENSATE DRAIN
TRAP LOCATION
(DOWNFLOW &
HORIZONTAL RIGHT)
OR ALTERNATE
1
⁄2-IN. DIA GAS CONN
⁄8-IN. DIA (22mm)
POWER CONN
7
INLET
23 1⁄4" TYP (591mm)
SIDE INLET
⁄16"
TYP
(14mm)
A
A
17-1/2 (445)
17-1/2 (445)
17-1/2 (445)
21 (533)
21 (533)
24-1/2 (622)
D
15-7/8 (403)
15-7/8 (403)
15-7/8 (403)
19-3/8 (492)
19-3/8 (492)
22---7/8 (581)
Fig. 2 -- Dimensional Drawing
6
E
16 (406)
16 (406)
16 (406)
19-1/2 (495)
19-1/2 (495)
23 (584)
⁄16" (17mm)
352AAV
335122-201 REV. B LIT TOP
A08435
Fig. 3 -- Clearances to Combustibles
Step 3 -- Combustion and Ventilation Air
Step 6 -- Gas Piping and Gas Pipe Pressure Testing
S US: Section 9.3 of the NFPA 54/ANSI Z223.1--2006, Air for
Combustion and Ventilation
S CANADA: Part 8 of the CAN/CSA--B149.1--05, Venting
Systems and Air Supply for Appliances
S US: NFPA 54/ANSI Z223.1--2006; chapters 5, 6, 7, and 8 and
national plumbing codes.
S CANADA: CAN/CSA--B149.1--05 Parts 4, 5, and 6, A, B, E,
G, and H.
Step 4 -- Duct Systems
In the state of Massachusetts:
S This product must be installed by a licensed plumber or gas fitter.
S When flexible connectors are used, the maximum length shall
not exceed 36 in. (914 mm)
S When lever type gas shutoffs are used they shall not exceed 36 in.
(914 mm).
S The use of copper tubing for gas piping is not approved by the
state of Massachusetts.
S US and CANADA: Air Conditioning Contractors Association
(ACCA) Manual D, Sheet Metal and Air Conditioning
Contractors National Association (SMACNA), or American
Society of Heating, Refrigeration, and Air Conditioning Engineers
(ASHRAE) 2001 Fundamentals Handbook Chapter 34 or 2000
HVAC Systems and Equipment Chapters 9 and 16.
Step 5 -- Acoustical Lining and Fibrous Glass Duct
Step 7 -- Electrical Connections
S US and CANADA: current edition of SMACNA, NFPA 90B as
tested by UL Standard 181 for Class I Rigid Air Ducts
S US: National Electrical Code (NEC) ANSI/NFPA 70--2008
S CANADA: Canadian Electrical Code CSA C22.1
7
INTRODUCTION
Step 8 -- Venting
S US: NFPA 54/ANSI Z223.1--2006 Chapters 12 and 13.
S CANADA: CAN/CSA--B149.1--05 Part 8 and Appendix C
0
The model 352AAV 4-way multipoise, Gas-Fired, Category IV,
condensing furnace is available in model sizes ranging from input
capacity of 60,000 to 120,000 Btuh as a direct vent (2-pipe)
application as well as a non-direct vent (1-pipe) application.
(27º C)
APPLICATIONS
!
CAUTION
MINOR PROPERTY DAMAGE
Failure to follow this caution may result in minor property
damage.
352AAV
60
Local codes may require a drain pan under entire furnace and
condensate trap when a condensing furnace is used in an attic
application or over a finished ceiling.
(16º C)
Step 1 -- General
Some assembly and modifications are required for furnaces
installed in any of the 4 applications shown in Fig. 1. All drain
and pressure tubes are connected as shown in Fig. 6. See
appropriate application instructions for these procedures.
Fig. 4 -- Return--Air Temperature
A05004
Step 2 -- Upflow Applications
ELECTROSTATIC DISCHARGE (ESD)
PRECAUTIONS PROCEDURE
!
In an upflow application, the blower is located below the burner
section, and conditioned air is discharged upwards.
CAUTION
CONDENSATE TRAP LOCATION
(FACTORY-SHIPPED ORIENTATION)
The condensate trap is factory installed in the blower shelf and
factory connected for UPFLOW applications. A factory-supplied
tube is used to extend the condensate trap drain connection to the
desired furnace side for field drain attachment. See Condensate
Trap Tubing (Factory-Shipped Orientation) section for drain tube
extension details. (See Fig. 5.)
UNIT DAMAGE HAZARD
Failure to follow this caution may result in damage to unit
components.
Electrostatic discharge can affect electronic components.
Take precautions during furnace installation and servicing to
protect the furnace electronic control. Precautions will
prevent electrostatic discharges from personnel and hand
tools which are held during the procedure. These precautions
will help to avoid exposing the control to electrostatic
discharge by putting the furnace, the control, and the person
at the same electrostatic potential.
CONDENSATE TRAP TUBING
(FACTORY-SHIPPED ORIENTATION)
NOTE: See Fig.6 or tube routing label on main furnace door to
confirm location of these tubes.
1. Collector Box Drain, Inducer Housing Drain, Relief Port,
and Pressure Switch Tubes
These tubes should be factory attached to condensate trap
and pressure switch ready for use in upflow applications.
These tubes can be identified by their connection location
and also by a color label on each tube. These tubes are
identified as follows: collector box drain tube (blue label),
inducer housing drain tube (violet label or molded), relief
port tube (green label), and pressure switch tube (pink
label).
2. Condensate Trap Drain Tube
The condensate trap drain connection must be extended
for field attachment by doing the following:
f. Determine location of field drain connection. (See Fig.
2 or 6)
NOTE: If internal filter or side Filter/Media Cabinet is used,
drain tube should be located to opposite side of casing from
return duct attachment to assist in filter removal.
g. Remove and discard casing drain hole plug button
from desired side.
h. Install drain tube coupling grommet (factory-supplied
in loose parts bag) in selected casing hole.
i. Slide drain tube coupling (factory-supplied in loose
parts bag) through grommet ensuring long end of
coupling faces blower.
1. Disconnect all power to the furnace. Multiple disconnects
may be required. DO NOT TOUCH THE CONTROL OR
ANY WIRE CONNECTED TO THE CONTROL PRIOR
TO DISCHARGING YOUR BODY’S ELECTROSTATIC
CHARGE TO GROUND.
2. Firmly touch the clean, unpainted, metal surface of the
furnace chassis which is close to the control. Tools held in
hand during grounding will be discharged.
3. After touching the chassis, you may proceed to service the
control or connecting wires as long as you do nothing to
recharge your body (moving or shuffling feet, touching
ungrounded objects, etc.).
4. If you touch ungrounded objects, firmly touch a clean,
unpainted metal surface of the furnace again before
touching control or wires.
5. Use this procedure for installed and uninstalled
(ungrounded) furnaces.
6. Before removing a new control from its container,
discharge your body’s electrostatic charge to ground to
protect the control from damage. If the control is to be
installed in a furnace, follow items 1 through 4 before
bringing the control or yourself in contact with the
furnace. Put all used and new controls into containers
before touching ungrounded objects.
7. An ESD service kit (available from commercial sources)
may also be used to prevent ESD damage.
8
FURNACE
DOOR
BLOWER SHELF
CONDENSATE
TRAP
CONDENSATE
TRAP (INSIDE)
FURNACE
DOOR
FURNACE
SIDE
4 7 8 124 mm
4
102 mm
FURNACE
SIDE
5 3 4 146 mm
5 3 4 146 mm
4
FIELD
DRAIN
CONN
ALTERNATE DRAIN
TUBE LOCATION
26 1 4 667 mm
26 1 4
11 2
667 mm
38 mm
SIDE VIEW
CONDENSATE TRAP
DRAIN TUBE LOCATION
FIELD
DRAIN
CONN
FRONT VIEW
END VIEW
FRONT VIEW
HORIZONTAL
APPLICATIONS
352AAV
DOWNFLOW AND ALTERNATE
EXTERNAL UPFLOW APPLICATIONS
UPFLOW APPLICATIONS
3 4 19 mm
SLOT FOR SCREW
HORIZONTAL
APPLICATION
(OPTIONAL)
1/4 OD
COLLECTOR BOX TO
TRAP RELIEF PORT
1 1 2 38 mm
1/2 OD
INDUCER HOUSING
DRAIN CONNECTION
19 mm 3 4
5/8 OD
COLLECTOR BOX
DRAIN CONNECTION
71 8
181 mm
SCREW HOLE FOR
UPFLOW OR DOWNFLOW APPLICATIONS
(OPTIONAL)
13 4 45 mm
WIRE TIE
GUIDES
(WHEN USED)
78
22 mm
FRONT VIEW
21 4
57 mm
1/2-IN.
PVC OR CPVC
SIDE VIEW
A93026
Fig. 5 -- Condensate Trap
j. Cement 2 factory-supplied 1/2-in. (13 mm) street CPVC
elbows to the rigid drain tube connection on the
condensate trap. (See Fig. 6.) These elbows must be
cemented together and cemented to condensate trap drain
connection.
NOTE: Failure to use CPVC elbows may allow drain to kink
and prevent draining.
k. Connect larger diameter drain tube and clamp (factory
supplied in loose parts bag) to condensate trap and
clamp securely.
l. Route tube to coupling and cut to appropriate length.
m. Attach tube to coupling and clamp securely.
!
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal injury
or death.
Casing hole filler cap must be installed in blower shelf hole
when condensate trap is relocated to prevent combustion
products being drawn in from appliances in the
equipment room.
4. Install condensate trap into left-hand side casing hole by
inserting tube connection stubs through casing hole and
rotating until tabs snap into locking position.
5. Fill unused condensate trap casing holes with plastic filler
caps (factory-supplied in loose parts bag).
CONDENSATE TRAP LOCATION (ALTERNATE
UPFLOW ORIENTATION)
An alternate location for the condensate trap is the left-hand side
of casing. (See Fig. 2 and 7.)
NOTE: If the alternate left-hand side of casing location is used,
the factory-connected drain and relief port tubes must be
disconnected and modified for attachment. See Condensate Trap
Tubing (Alternate Upflow Orientation) section for tubing
attachment. To relocate condensate trap to the left hand side,
perform the following:
1. Remove 3 tubes connected to condensate trap.
2. Remove trap from blower shelf by gently pushing tabs
inward and rotating trap.
3. Install casing hole filler cap (factory-supplied in loose
parts bag) into blower shelf hole where trap was removed.
CONDENSATE TRAP TUBING (ALTERNATE
UPFLOW ORIENTATION)
NOTE: See Fig.7 or tube routing label on main furnace door to
confirm location of these tubes.
1. Collector Box Drain
Tube Connect collector box drain tube (blue label) to
condensate trap.
NOTE: On 17--1/2 in. (445 mm) wide furnaces ONLY, cut tube
between corrugated sections to prevent kinks from occurring.
9
PLUG
PLUG
CAP
CAP
COLLECTOR BOX
DRAIN TUBE (BLUE
& WHITE STRIPED)
COLLECTOR BOX
DRAIN TUBE (BLUE
& WHITE STRIPED)
COLLECTOR BOX
TUBE (PINK)
COLLECTOR BOX
TUBE (PINK)
COLLECTOR BOX
TUBE (GREEN)
352AAV
COLLECTOR BOX
TUBE (GREEN)
COLLECTOR BOX
DRAIN TUBE (BLUE)
INDUCER HOUSING
(MOLDED) DRAIN
TUBE (BEHIND
COLLECTOR BOX
DRAIN TUBE)
CONDENSATE
TRAP
COLLECTOR BOX
DRAIN TUBE (BLUE)
CONDENSATE
TRAP
INDUCER
HOUSING
DRAIN TUBE
(VIOLET)
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN TUBE
COUPLING (LEFT
DRAIN OPTION)
A01031
Fig. 7 -- Alternate Upflow Configuration and Trap Location
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN TUBE
FIELD-INSTALLED
FACTORY-SUPPLIED
1⁄2-IN. (13 mm) CPVC STREET
ELBOWS (2) FOR
LEFT DRAIN OPTION
PRESSURE SWITCH TUBING
FIELD-INSTALLED
FACTORY-SUPPLIED
DRAIN TUBE
COUPLING (RIGHT
DRAIN OPTION)
The LOWER collector box pressure tube (pink label) is factory
connected to the High Pressure Switch and should not require
any modification.
NOTE: See Fig.6 or 7 or tube routing label on main furnace
door to check for proper connections.
A01030
Fig. 6 -- Factory-Shipped Upflow Tube Configuration
(Shown with Blower Access Panel Removed)
UPPER COLLECTOR BOX AND INDUCER
HOUSING (UNUSED) DRAIN CONNECTIONS
2. Inducer Housing Drain Tube
a. Remove and discard LOWER (molded) inducer
housing drain tube which was previously connected to
condensate trap.
b. Use inducer housing drain extension tube (violet label
and factory-supplied in loose parts bag) to connect
LOWER inducer housing drain connection to the
condensate trap.
c. Determine appropriate length, cut, and connect tube.
d. Clamp tube to prevent any condensate leakage.
3. Relief Port Tube
a. Connect relief port tube (green label) to
condensate trap.
b. Extend this tube (if required) by splicing to small
diameter tube (factory-supplied in loose parts bag).
c. Determine appropriate length, cut, and connect tube.
Upper Collector Box Drain Connection
Attached to the UPPER collector box drain connection is a
factory-installed corrugated, plugged tube (blue and white striped
label). This tube is plugged to prevent condensate leakage in this
application. Ensure this tube is plugged.
NOTE: See Fig.6 or 7 or tube routing label on main furnace door
to check for proper connections.
Upper Inducer Housing Drain Connection
Attached to the UPPER (unused) inducer housing drain
connection is a cap and clamp. This cap is used to prevent
condensate leakage in this application. Ensure this connection
is capped.
NOTE: See Fig.6 or 7 or tube routing label on main furnace door
to check for proper connections.
CONDENSATE TRAP FREEZE PROTECTION
Refer to Condensate Drain
recommendations and procedures.
CONDENSATE TRAP FIELD DRAIN
ATTACHMENT
Protection
section
for
Step 3 -- Downflow Applications
Refer to Condensate Drain section for recommendations
and procedures.
In a downflow furnace application, the blower is located above
the burner section, and conditioned air is discharged downwards.
CONDENSATE TRAP LOCATION
The condensate trap must be removed from the factory-installed
blower shelf location and relocated in selected application
location as shown in Fig. 2, 8, or 9.
10
COLLECTOR BOX
DRAIN TUBE (BLUE)
CAP
PLUG
PLUG
CAP
COLLECTOR BOX
TUBE (GREEN)
COLLECTOR BOX
DRAIN TUBE (BLUE)
COLLECTOR BOX
EXTENSION TUBE
COLLECTOR BOX
TUBE (PINK)
COLLECTOR BOX
TUBE (PINK)
COLLECTOR BOX
DRAIN TUBE (BLUE
& WHITE STRIPED)
COLLECTOR BOX
DRAIN TUBE (BLUE
& WHITE STRIPED)
COLLECTOR BOX
EXTENSION TUBE
COLLECTOR BOX
EXTENSION TUBE
INDUCER HOUSING
DRAIN TUBE
(VIOLET)
CONDENSATE
TRAP
CONDENSATE
TRAP
COLLECTOR BOX
EXTENSION
DRAIN TUBE
INDUCER HOUSING
DRAIN TUBE (VIOLET)
DRAIN TUBE
COUPLING
A01023
A01024
Fig. 8 -- Downflow Tube Configuration
(Left-Hand Trap Installation)
Fig. 9 -- Downflow Tube Configuration
(Right-Hand Trap Installation)
To relocate condensate trap from the blower shelf to desired
location, perform the following:
1. Remove 3 tubes connected to condensate trap.
2. Remove trap from blower shelf by gently pushing tabs
inward and rotating trap.
3. Remove casing hole filler cap from casing hole.
(See Fig. 2, 8, or 9.)
4. Install casing hole filler cap into blower shelf hole where
trap was removed.
!
b. Install removed clamp and plug into UPPER collector
box drain tube (blue label) which was connected to
condensate trap.
c. Connect LOWER collector box drain connection to
condensate trap.
(3.) Condensate Trap Located on Left Side of Casing
a. Connect LOWER collector box drain tube (blue
and white striped label) to condensate trap.
Tube does not need to be cut.
b. Clamp tube to prevent any condensate leakage.
(4.) Condensate Trap Located on Right Side of Casing
a. Install drain tube coupling (factory-supplied in
loose parts bag) into collector box drain tube
(blue and white striped label) which was
previously plugged.
b. Connect
larger
diameter
drain
tube
(factory-supplied in loose parts bag) to drain
tube coupling, extending collector box drain
tube for connection to condensate trap.
c. Route extended collector box drain tube
directly from collector box drain to condensate
trap as shown in Fig. 9.
d. Determine appropriate length and cut.
e. Connect to condensate trap.
f. Clamp tube to prevent any condensate leakage.
2. Inducer Housing Drain Tube
a. Remove factory-installed cap and clamp from LOWER
inducer housing drain connection.
b. Remove and discard UPPER (molded) inducer housing
drain tube which was previously connected to
condensate trap.
c. Install cap and clamp on UPPER inducer housing drain
connection where molded drain tube was removed.
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal injury
or death.
Casing hole filler cap must be installed in blower shelf hole
when condensate trap is relocated to prevent combustion
products being drawn in from appliances in the
equipment room.
5. Install condensate trap into desired casing hole by
inserting tube connection stubs through casing hole and
rotating until tabs snap into locking position.
CONDENSATE TRAP TUBING
NOTE: See Fig. 8 or 9 or tube routing label on main furnace
door to check for proper connections.
Relocate tubes as described below.
1. Collector Box Drain Tube
a. Remove factory-installed plug from LOWER collector
box drain tube (blue and white striped label).
11
352AAV
COLLECTOR BOX
TUBE (GREEN)
COLLECTOR BOX
EXTENSION TUBE
352AAV
Step 4 -- Horizontal Left (Supply-Air Discharge)
Applications
d. Use inducer housing drain tube (violet label and
factory-supplied in loose parts bag) to connect
LOWER inducer housing drain connection to the
condensate trap.
e. Connect inducer housing drain connection to
condensate trap.
(1.) Condensate Trap Located on Left Side of Casing
a. Determine appropriate length and cut.
b. Connect tube to condensate trap.
c. Clamp tube to prevent any condensate leakage.
(2.) Condensate Trap Located on Right Side of Casing
a. Route inducer housing drain tube (violet label)
directly from inducer housing to condensate
trap as shown in Fig. 9.
b. Determine appropriate length and cut.
c. Connect tube to condensate trap.
d. Clamp tube to prevent any condensate leakage.
3. Relief Port Tube Refer to Pressure Switch Tubing section
for connection procedure.
In a horizontal left furnace application, the blower is located to
the right of the burner section, and conditioned air is discharged
to the left.
CONDENSATE TRAP LOCATION
The condensate trap must be removed from the factory-installed
blower shelf location and relocated in selected application
location as shown in Fig. 2 or 10.
To relocate condensate trap from the blower shelf to desired
location, perform the following:
1. Remove 3 tubes connected to condensate trap.
2. Remove trap from blower shelf by gently pushing tabs
inward and rotating trap.
3. Install casing hole filler cap (factory-supplied in loose
parts bag) into blower shelf hole where trap was removed.
!
CARBON MONOXIDE POISONING HAZARD
CONDENSATE TRAP FIELD DRAIN
ATTACHMENT
Failure to follow this warning could result in personal injury
or death.
Refer to Condensate Drain section for recommendations
and procedures.
Casing hole filler cap must be installed in blower shelf hole
when condensate trap is relocated to prevent combustion
products being drawn in from appliances in the
equipment room.
PRESSURE SWITCH TUBING
One collector box pressure tube (pink label) is factory connected
to the High Pressure Switch for use when furnace is installed in
upflow applications. This tube MUST be disconnected and used
for the condensate trap relief port tube. The other collector box
pressure tube (green label) which was factory connected to the
condensate trap relief port connection MUST be connected to the
High Pressure Switch in DOWNFLOW or HORIZONTAL
RIGHT applications
NOTE: See Fig. 8 or 9 or tube routing label on main furnace
door to check for proper connections.
1. Disconnect collector box pressure tube (pink label)
attached to High Pressure Switch.
2. Extend collector box pressure tube (green label) which
was previously connected to condensate trap relief port
connection by splicing to small diameter tube
(factory-supplied in loose parts bag).
3. Connect collector box pressure tube (green label) to High
Pressure Switch connection labeled COLLECTOR BOX.
4. Extend collector box pressure tube (pink label) which was
previously connected to High Pressure Switch by splicing
to remaining small diameter tube (factory-supplied in
loose parts bag).
5. Route this extended tube (pink label) to condensate trap
relief port connection.
6. Determine appropriate length, cut, and connect tube.
7. Clamp tube to relief port connection.
4. Install condensate trap into left-hand side casing hole by
inserting tube connection stubs through casing hole and
rotating until tabs snap into locking position.
5. Fill unused condensate trap casing holes with plastic filler
caps (factory-supplied in loose parts bag).
CONDENSATE TRAP TUBING
NOTE: See Fig. 10 or tube routing label on main furnace door to
check for proper connections.
1. Collector Box Drain Tube
a. Install drain tube coupling (factory-supplied in loose
parts bag) into collector box drain tube (blue label)
which was previously connected to condensate trap.
b. Connect large diameter drain tube and clamp
(factory-supplied in loose parts bag) to drain tube
coupling, extending collector box drain tube.
c. Route extended tube (blue label) to condensate trap
and cut to appropriate length.
d. Clamp tube to prevent any condensate leakage.
2. Inducer Housing Drain Tube
a. Remove and discard LOWER (molded) inducer
housing drain tube which was previously connected to
condensate trap.
b. Use inducer housing drain extension tube (violet label
and factory-supplied in loose parts bag) to connect
LOWER inducer housing drain connection to the
condensate trap.
c. Determine appropriate length, cut, and connect tube.
d. Clamp tube to prevent any condensate leakage.
CONDENSATE TRAP FREEZE PROTECTION
Refer to Condensate Drain
recommendations and procedures.
Protection
WARNING
section
for
12
PLUG
CAP
CONDENSATE
TRAP
352AAV
COLLECTOR BOX
DRAIN TUBE
(BLUE AND WHITE STRIPED)
AUXILIARY "J" BOX
COLLECTOR BOX
TUBE (GREEN)
INDUCER HOUSING
DRAIN TUBE (VIOLET)
COLLECTOR
BOX EXTENSION
DRAIN TUBE
COLLECTOR BOX
DRAIN TUBE (BLUE)
COLLECTOR BOX
EXTENSION TUBE
DRAIN TUBE COUPLING
COLLECTOR BOX TUBE (PINK)
RELOCATE TUBE BETWEEN BLOWER SHELF AND INDUCER HOUSING FOR
040, 060, AND 080 HEATING INPUT FURNACES
A01029
Fig. 10 -- Horizontal Left Tube Configuration
4. Determine appropriate length, cut, and reconnect tube to
High
Pressure
Switch
connection
labeled
COLLECTOR BOX.
3. Relief Port Tube
a. Extend collector box tube (green label) which was
previously connected to the condensate trap by splicing
to small diameter tube (factory-supplied in loose parts
bag).
b. Route extended collector box pressure tube to relief
port connection on the condensate trap.
c. Determine appropriate length, cut, and connect tube.
d. Clamp tube to prevent any condensate leakage.
CONDENSATE TRAP FREEZE PROTECTION
Refer to Condensate Drain
recommendations and procedures.
Protection
section
for
CONSTRUCT A WORKING PLATFORM
Construct working platform where all required furnace clearances
are met. (See Fig. 3 and 11 or 12.)
CONDENSATE TRAP FIELD DRAIN
ATTACHMENTS
!
Refer to Condensate Drain section for recommendations and
procedures.
CAUTION
UNIT MAY NOT OPERATE
PRESSURE SWITCH TUBING
Failure to follow this caution may result in intermittent
unit operation.
The LOWER collector box pressure tube (pink label) is factory
connected to the High Pressure Switch for use when furnace is
installed in UPFLOW applications. This tube MUST be
disconnected, extended, rerouted, and then reconnected to the
pressure switch in HORIZONTAL LEFT applications for 060 and
080 heating input furnaces.
NOTE: See Fig. 10 or tube routing label on main furnace door to
check for proper connections.
Modify tube as described below:
1. Disconnect collector box pressure tube (pink label)
attached to High Pressure Switch.
2. Use smaller diameter tube (factory-supplied in loose parts
bag) to extend tube disconnected in item 1.
3. Route extended tube:
a. Behind inducer housing.
b. Between blower shelf and inducer housing.
The condensate trap MUST be installed below furnace. See
Fig. 5 for dimensions. The drain connection to condensate trap
must also be properly sloped to an open drain.
NOTE: Combustion-air and vent pipes are restricted to a
minimum length of 5 ft. (2 M)(See Table 13.)
NOTE: A 12-in. (305 mm) minimum offset pipe section is
recommended with short (5 to 8 ft or 2 to 3 M)) vent systems.
This recommendation is to reduce excessive condensate droplets
from exiting the vent pipe. (See Fig. 11, 12 or 43.)
Step 5 -- Horizontal Right (Supply-Air Discharge)
Applications
In a horizontal right furnace application, the blower is located to
the left of the burner section, and conditioned air is discharged to
the right.
13
COMBUSTION - AIR
INTAKE
VENT
A 12-IN. (305 mm) MIN HORIZONTAL PIPE
SECTION IS RECOMMENDED WITH
SHORT (5 TO 8 FT / 1.5 TO 2.4 M) VENT
SYSTEMS TO REDUCE EXCESSIVE
CONDENSATE DROPLETS FROM
EXITING THE VENT PIPE.
30″ (762 mm)MIN
WORK AREA
352AAV
5 3/4″ (146 mm)
MANUAL
SHUTOFF
GAS VALVE
ACCESS OPENING
FOR TRAP
SEDIMENT
TRAP
DRAIN
CONDENSATE
TRAP
NOTE: LOCAL CODES MAY REQUIRE A DRAIN PAN UNDER THE
FURNACE AND CONDENSATE TRAP WHEN A CONDENSING
FURNACE IS INSTALLED ABOVE FINISHED CEILINGS.
A93031
Fig. 11 -- Attic Location and Working Platform for Direct Vent (2-Pipe) Applications
!
CAUTION
!
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal injury
or death.
Casing hole filler cap must be installed in blower shelf hole
when condensate trap is relocated to prevent combustion
products being drawn in from appliances in the
equipment room.
MINOR PROPERTY DAMAGE
Failure to follow this caution may result in minor property
damage.
Local codes may require a drain pan under entire furnace and
condensate trap when a condensing furnace is used in an attic
application or over a finished ceiling.
NOTE: The auxiliary junction box (J-Box) MUST be relocated
to opposite side of furnace casing. (See Fig. 13.) See Electrical
Connection section for J-Box relocation.
4. Install condensate trap into right-hand side casing hole by
inserting tube connection stubs through casing hole and
rotating until tabs snap into locking position.
5. Fill unused condensate trap casing holes with plastic filler
caps (factory-supplied in loose parts bag).
CONDENSATE TRAP LOCATION
The condensate trap must be removed from the factory-installed
blower shelf location and relocated in selected application
location as shown in Fig. 2 or 13.
To relocate condensate trap from the blower shelf to desired
location, perform the following:
1. Remove 3 tubes connected to condensate trap.
2. Remove trap from blower shelf by gently pushing tabs
inward and rotating trap.
3. Install casing hole filler cap (factory-supplied in loose
parts bag) into blower shelf hole where trap was removed.
CONDENSATE TRAP TUBING
NOTE: See Fig. 13 or tube routing label on main furnace door to
check for proper connections.
1. Collector Box Drain Tube:
a. Remove factory-installed plug from LOWER collector
box drain tube (blue and white striped label).
b. Install removed clamp and plug into UPPER collector
box drain tube (blue label) which was previously
connected to condensate trap.
c. Connect LOWER collector box drain tube (blue and
white striped label) to condensate trap. Tube does not
need to be cut.
d. Clamp tube to prevent any condensate leakage.
14
A 3-IN.(76mm) MINIMUM CLEARANCE
TO COMBUSTION-AIR INTAKE
IS REQUIRED.
VENT
COMBUSTION AIR
INTAKE
A 12-IN. (305mm) MIN HORIZONTAL PIPE
SECTION IS RECOMMENDED WITH
SHORT (5 TO 8 FT / 1.5 TO 2.4M) VENT
SYSTEMS TO REDUCE EXCESSIVE
CONDENSATE DROPLETS FROM
EXITING THE VENT PIPE.
30-IN. (762mm) MIN
WORK AREA
352AAV
5 3/4 IN. (146mm)
MANUAL
SHUTOFF
GAS VALVE
ACCESS OPENING
FOR TRAP
SEDIMENT
TRAP
DRAIN
CONDENSATE
TRAP
NOTE: LOCAL CODES MAY REQUIRE A DRAIN PAN UNDER THE
FURNACE AND CONDENSATE TRAP WHEN A CONDENSING
FURNACE IS INSTALLED ABOVE FINISHED CEILINGS.
A96184
Fig. 12 -- Attic Location and Working Platform for Non-Direct Vent (1-pipe) Applications
NOTE: See Fig. 12 or tube routing label on main furnace door to
check for proper connections.
Relocate tubes as described below.
1. Disconnect collector box pressure tube (pink label)
attached to High Pressure Switch.
2. Extend collector box pressure tube (green label) which
was previously connected to condensate trap relief port
connection by splicing to small diameter tube
(factory-supplied in loose parts bag).
3. Connect collector box pressure tube (green label) to High
Pressure Switch connection labeled COLLECTOR BOX.
4. Use remaining smaller diameter tube (factory-supplied in
loose parts bag) to extend collector box pressure tube
(pink label) which was previously connected to High
Pressure Switch. Route this extended tube (pink label) to
condensate trap relief port connection.
5. Determine appropriate length, cut, and connect tube.
6. Clamp tube to relief port connection.
2. Inducer Housing Drain Tube:
a. Remove factory-installed cap and clamp from LOWER
inducer housing drain connection.
b. Remove and discard UPPER (molded) inducer housing
drain tube which was previously connected to
condensate trap.
c. Install cap and clamp on UPPER inducer housing drain
connection where molded drain tube was removed.
d. Use inducer housing drain extension tube (violet label
and factory-supplied in loose parts bag) to connect
LOWER inducer housing drain connection to
condensate trap.
e. Determine appropriate length, cut, and connect tube to
condensate trap.
f. Clamp tube to prevent any condensate leakage.
3. Relief Port Tube:
Refer to Pressure Switch Tubing section for connection
procedure.
CONDENSATE TRAP FIELD DRAIN ATTACHMENT
CONDENSATE TRAP FREEZE PROTECTION
Refer to Condensate Drain section for recommendations
and procedures.
Refer to Condensate Drain
recommendations and procedures.
PRESSURE SWITCH TUBING
CONSTRUCT A WORKING PLATFORM
One collector box pressure tube (pink label) is factory connected
to the High Pressure Switch for use when furnace is installed in
UPFLOW applications. This tube MUST be disconnected and
used for the condensate trap relief port tube. The other collector
box pressure tube (green label) which was factory connected to
the condensate trap relief port connection MUST be connected to
the High Pressure Switch in DOWNFLOW or HORIZONTAL
RIGHT applications.
Construct working platform where all required furnace clearances
are met. (See Fig. 3 and 11 or 12.)
15
Protection
section
for
COLLECTOR BOX DRAIN TUBE (BLUE)
COLLECTOR BOX TUBE (GREEN)
CAP
COLLECTOR BOX EXTENSION TUBE
COLLECTOR BOX TUBE (PINK)
PLUG
352AAV
AUXILARY “J” BOX RELOCATED HERE
CONDENSATE
TRAP
COLLECTOR BOX DRAIN TUBE
(BLUE AND WHITE STRIPED)
INDUCER HOUSING
DRAIN TUBE (VIOLET)
COLLECTOR BOX
EXTENSION TUBE
A01028
Fig. 13 -- Horizontal Right Tube Configuration
!
shown on the furnace clearance to combustibles label.
CAUTION
NOTE: For upflow/downflow applications install furnace so that
it is level or pitched forward within 1/2-in. (13 mm) for proper
furnace operation. For horizontal applications pitch 1/4-in. (6
mm) minimum to 1/2-in. (13 mm) maximum forward to ensure
proper condensate drainage from secondary heat exchangers.
(See Fig. 14.)
When a furnace is installed so that supply ducts carry air
circulated by the furnace to areas outside the space containing the
furnace, return air must also be handled by ducts sealed to
furnace casing. The ducts terminate outside the space containing
the furnace to ensure a negative pressure condition will not occur
within equipment room or space.
UNIT MAY NOT OPERATE
Failure to follow this caution may result in intermittent
unit operation.
The condensate trap MUST be installed below furnace. See
Fig. 5 for dimensions. The drain connection to condensate
trap must also be properly sloped to an open drain.
NOTE: Combustion-air pipe (when applicable) and vent pipe(s)
are restricted to a minimum length of 5 ft. (2 M). (See Table 13.)
NOTE: A 12-in. (305 mm) minimum offset pipe section is
recommended with short (5 to 8 ft or 2 to 3 M) vent systems. This
recommendation is to reduce excessive condensate droplets from
exiting the vent pipe. (See Fig. 11, 12 or 43.)
!
WARNING
FIRE, INJURY OR DEATH HAZARD
Failure to follow this warning could result in fire, property
damage, personal injury, or death.
Do not install furnace on its back. (See Fig. 15.) Safety control
operation will be adversely affected. Never connect return-air
ducts to back of furnace.
LOCATION
Step 1 -- General
This furnace must
S be installed so the electrical components are protected from water.
S not be installed directly on any combustible material other than
wood flooring (refer to SAFETY CONSIDERATIONS).
S be located so combustion-air and vent pipe maximum lengths
are not exceeded. Refer to Table 13.
S be located where available electric power and gas supplies
meet specifications on the furnace rating plate.
S be attached to an air distribution system and be located as close
to the center of the distribution system as possible. Refer to Air
Ducts section.
S be provided with ample space for servicing and cleaning.
Always comply with minimum fire protection clearances
LEVEL 0″
TO
1⁄2″ MAX
(0 to 13 mm)
FRONT
MIN 1⁄4″
TO
1⁄2″ MAX
(6 to 13 mm)
UPFLOW OR DOWNFLOW
FRONT
HORIZONTAL
A02146
Fig. 14 -- Proper Condensate Drainage
16
CAUTION
FRONT
UNIT DAMAGE HAZARD
This gas furnace may be used for construction heat provided that:
--The furnace is permanently installed with all electrical
wiring, piping, air filters, venting and ducting installed
according to these installation instructions. A return air duct
is provided, sealed to the furnace casing, and terminated
outside the space containing the furnace. This prevents a
negative pressure condition as created by the circulating air
blower, causing a flame rollout and/ or drawing combustion
products into the structure.
--The furnace is controlled by a thermostat. It may not be “hot
wired” to provide heat continuously to the structure without
thermostatic control.
--Clean outside air is provided for combustion. This is to
minimize the corrosive effects of adhesives, sealers and other
construction materials. It also prevents the entrainment of
drywall dust into combustion air, which can cause fouling
and plugging of furnace components.
--The temperature of the return air to the furnace is
maintained between 55°F (13°C) and 80°F (27°C), with no
evening setback or shutdown. The use of the furnace while
the structure is under construction is deemed to be
intermittent operation per our installation instructions.
--The air temperature rise is within the rated rise range on the
furnace rating plate, and the firing rate has been set to the
nameplate value.
--The filters used to clean the circulating air during the
construction process must be either changed or thoroughly
cleaned prior to occupancy.
--The furnace, ductwork and filters are cleaned as necessary
to remove drywall dust and construction debris from all
HVAC system components after construction is completed.
-- After construction is complete, verify furnace operating
conditions including ignition, input rate, temperature rise and
venting, according to the manufacturer’s instructions.
!
B
A
C
K
BACK
FRONT
A93043
Fig. 15 -- Prohibit Installation on Back
352AAV
!
Step 3 -- Hazardous Locations
!
WARNING
FIRE, EXPLOSION, INJURY OR DEATH HAZARD
Improper location or inadequate protection could result in fire
or explosion.
When the furnace is installed in a residential garage, the
burners and ignition sources must be located at least 18 in.
(457 mm) above the floor. The furnace must be located or
protected to avoid physical damage by vehicles. When the
furnace is installed in a public garage, airplane hangar, or other
building having a hazardous atmosphere, the furnace must be
installed in accordance with current edition of the NFGC or
NSCNGPIC. (See Fig. 17.)
Step 4—Furnace Location and Application
DIRECT VENT (2-PIPE) APPLICATION
CAUTION
Furnace may be located in a confined space without special
provisions for dilution or ventilation air.
UNIT DAMAGE HAZARD
Failure to follow this caution may result in minor property or
unit damage.
If this furnace is installed in an unconditioned space where
the ambient temperatures may be 32°F (0°C)or lower, freeze
protection measures must be taken. (See Fig. 16.)
Step 2 -- Furnace Location Relative to Cooling
Equipment
The cooling coil must be installed parallel with or on downstream
side of furnace to avoid condensation in heat exchanger. When
installed parallel with a furnace, dampers or other means used to
control flow of air shall be adequate to prevent chilled air from
entering furnace. If dampers are manually operated, they must be
equipped with a means to prevent operation of either unit unless
the damper is in full-heat or full-cool position.
A07911
Fig. 16 -- Freeze Protection
17
If air is exposed to the following substances, it should not be
used for combustion air, and outdoor air may be required
for combustion:
S Permanent wave solutions
S Chlorinated waxes and cleaners
S Chlorine based swimming pool chemicals
S Water softening chemicals
S De-icing salts or chemicals
S Carbon tetrachloride
S Halogen type refrigerants
S Cleaning solvents (such as perchloroethylene)
S Printing inks, paint removers, varnishes, etc.
S Hydrochloric acid
S Cements and glues
S Antistatic fabric softeners for clothes dryers
S Masonry acid washing materials
352AAV
18-IN. (457.2 mm)
MINIMUM TO BURNERS
A93044
Fig. 17 -- Installation in a Garage
All fuel-burning equipment must be supplied with air for fuel
combustion. Sufficient air must be provided to avoid negative
pressure in the equipment room or space. A positive seal must be
made between the furnace cabinet and the return-air duct to
prevent pulling air from the burner area and from draft
safeguard opening.
NON-DIRECT VENT (1-PIPE) APPLICATION
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in intermittent
unit operation.
Do not install furnace in a corrosive or contaminated
atmosphere. Make sure all combustion and circulating air
requirements are met.
!
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in personal injury
or death.
The operation of exhaust fans, kitchen ventilation fans, clothes
dryers, attic exhaust fans or fireplaces could create a
NEGATIVE PRESSURE CONDITION at the furnace.
Make-up air MUST be provided for the ventilation devices, in
addition to that required by the furnace. Refer to the Carbon
Monoxide Poisoning Hazard warning in the venting section of
these instructions to determine if an adequate amount of
make-up air is available.
Refer to the AIR FOR COMBUSTION AND VENTILATION
section for details.
AIR FOR COMBUSTION AND
VENTILATION
Provisions for adequate combustion, ventilation, and dilution air
must be provided in accordance with:
S U.S. Installations: Section 9.5 of the NFPA 54/ANSI
Z223.1--2006, Air for Combustion and Ventilation and
applicable provisions of the local building codes.
S Canadian Installations: Part 8 of the CAN/CSA--B149.1--05,
Venting Systems and Air Supply for Appliances and all
authorities having jurisdiction.
!
WARNING
The requirements for combustion and ventilation air depend upon
whether or not the furnace is located in a space having a volume
of at least 50 cubic feet per 1,000 Btuh input rating for all gas
appliances installed in the space.
S Spaces having less than 50 cubic feet per 1,000 Btuh require
the OUTDOOR COMBUSTION AIR METHOD.
S Spaces having at least 50 cubic feet per 1,000 Btuh may use
the INDOOR COMBUSTION AIR, STANDARD or
KNOWN AIR INFILTRATION METHOD.
Outdoor Combustion Air Method
1. Provide the space with sufficient air for proper
combustion, ventilation, and dilution of flue gases using
permanent horizontal or vertical duct(s) or opening(s)
directly communicating with the outdoors or spaces that
freely communicate with the outdoors.
2. Fig. 18 illustrates how to provide TWO OUTDOOR
OPENINGS, one inlet and one outlet combustion and
ventilation air openings to the outdoors.
a. One opening MUST commence within 12 in.(305 mm)
of the ceiling and the second opening MUST
commence within 12 in. (305 mm) of the floor.
b. Size openings and ducts per Fig. 18 and Table 1.
c. TWO HORIZONTAL DUCTS require 1 square inch of
free area per 2,000 Btuh (1,100 mm2/kW) of combined
input for all gas appliances in the space per Fig. 18 and
Table 1.
WARNING
FURNACE CORROSION HAZARD
Failure to follow this warning could result in reduced furnace
component life.
Air for combustion must not be contaminated by halogen
compounds, which include fluoride, chloride, bromide, and
iodide. These elements could corrode heat exchangers and
shorten furnace life. Air contaminants are found in aerosol
sprays, detergents, bleaches, cleaning solvents, salts, air
fresheners, and other household products.
The following types of furnace installations may require
OUTDOOR AIR for combustion due to chemical exposures:
S Commercial buildings
S Buildings with indoor pools
S Laundry rooms
S Hobby or craft rooms, and
S Chemical storage areas
18
Table 1 – Minimum Free Area Required for Each Combustion Air Opening or Duct to Outdoors
FURNACE
INPUT
(BTUH)
44,000
66,000
88,000
110,000
132,000
154,000
TWO HORIZONTAL DUCTS
(1 SQ. IN./2,000 BTUH) (1,100 SQ. MM/KW)
Free Area of
Opening and Duct
Sq. In. (mm)
22 (14194)
33 (21290)
44 (28387)
55 (35484)
66 (42581)
77 (49677)
Round Duct
Dia.
In. (mm)
6 (152)
7 (178)
8 (203)
9 (229)
10 (254)
10 (254)
SINGLE DUCT OR OPENING
(1 SQ. IN./3,000 BTUH) (734 SQ. MM/KW)
Free Area of Opening
and Duct
Sq. In (mm)
14.7 (9494)
22 (14193)
29.3 (18903)
36.7 (23677)
44 (28387)
51.3 (33096)
Round Duct
Dia.
In. (mm)
5 (127)
6 (152)
7 (178)
7 (178)
8 (203)
9 (229)
TWO OPENINGS OR VERTICAL DUCTS
(1 SQ. IN./4,000 BTUH) (550 SQ. MM/KW)
Free Area of Opening
and Duct
Sq. In (mm)
11 (7097)
16.5 (10645)
22 (14193)
27.5 (17741)
33 (21290)
38.5 (24838)
Round Duct
Dia.
In. (mm)
4 (102)
5 (127)
6 (152)
6 (152)
7 (198)
8 (203)
FURNACE
110,000
66,000
88,000
WATER HEATER
30,000
40,000
30,000
+
+
+
=
=
=
TOTAL INPUT
(140,000 divided by 4,000)
(106,000 divided by 3,000)
(118,000 divided by 2,000)
=
=
=
35.0 Sq. In. for each two Vertical Ducts or Openings
35.3 Sq. In. for a Single Duct or Opening
59.0 Sq. In. for each of two Horizontal Ducts
Table 2 – Minimum Space Volumes for 100% Combustion, Ventilation and Dilution Air from Outdoors
OTHER THAN FAN-ASSISTED TOTAL
(1,000’S BTUH GAS INPUT RATE)
30
40
50
ACH
0.60
1,050
(29.7)
1,400
(39.6)
1,750
(49.5)
FAN-ASSISTED TOTAL
(1,000’S BTUH GAS INPUT RATE)
44
66
88
110
132
Space Volume Ft3 (M3)
1,100
1,650
2,200
2,750
3,300
(31.1)
(46.7)
(62.2)
(77.8)
(93.4)
0.50
1,260
(35.6)
1,680
(47.5)
2,100
(59.4)
1,320
(37.3)
1,980
(56.0)
2,640
(74.7)
3,300
(93.4)
3,960
(112.1)
4,620
(130.8)
0.40
1,575
(44.5)
2,100
(59.4)
2,625
(74.3)
1,650
(46.7)
2,475
(70.0)
3,300
(93.4)
4,125
(116.8)
4,950
(140.1)
5,775
(163.5)
0.30
2,100
(59.4)
2,800
(79.2)
3,500
(99.1)
2,200
(62.2)
3,300
(93.4)
4,400
(124.5)
5,500
(155.7)
6,600
(186.8)
7,700
(218.0)
0.20
3,150
(89.1)
4,200
(118.9)
5,250
(148.6)
3,300
(93.4)
4,950
(140.1)
6,600
(186.8)
8,250
(233.6)
9,900
(280.3)
11,550
(327.0)
0.10
6,300
(178.3)
8,400
(237.8)
10,500
(297.3)
6,600
(186.8)
9,900
(280.3)
13,200
(373.7)
16,500
(467.2)
19,800
(560.6)
23,100
(654.1)
0.00
NP
NP
NP
NP
NP
NP
NP
NP
NP
3,850
(109.0)
Indoor Combustion AirE NFPA & AGA
Standard and Known-Air-Infiltration Rate Methods
Indoor combustion air is permitted for combustion, ventilation,
and dilution, if the Standard or Known-Air-Infiltration Rate
Method is used.
The Standard Method:
1. The space has no less volume than 50 cubic feet per 1,000
Btuh of the maximum input ratings for all gas appliances
installed in the space and
2. The air infiltration rate is not known to be less than 0.40
air changes per hour (ACH).
The Known Air Infiltration Rate Method shall be used, if the
infiltration rate is known to be:
1. Less than 0.40 ACH and
2. Equal to or greater than 0.10 ACH
Infiltration rates greater than 0.60 ACH shall not be used. The
minimum required volume of the space varies with the number of
ACH and shall be determined per Table 2 or Equations 1 and 2.
Determine the minimum required volume for each appliance in
the space and add the volumes together to get the total minimum
required volume for the space.
Table 2 -- Minimum Space Volumes were determined by using
the following equations from the National Fuel Gas Code ANSI
Z223.1--2006/NFPA 54--2006,9.3.2.2:
d. TWO OPENINGS OR VERTICAL DUCTS require 1
square inch of free area per 4,000 Btuh (550 mm2/kW)
for combined input of all gas appliances in the space
per Fig. 18 and Table 1.
3. ONE OUTDOOR OPENING requires:
a. 1 square inch of free area per 3,000 Btuh (734 mm2/kW)
for combined input of all gas appliances in the space
per Table 1 and 13.
b. Not less than the sum of the areas of all vent
connectors in the space.
The opening shall commence within 12 in. (305 mm)
of the ceiling. Appliances in the space shall have
clearances of at least 1 in. (25 mm) from the sides and
back and 6 in. (152 mm) from the front. The opening
shall directly communicate with the outdoors or shall
communicate through a vertical or horizontal duct to
the outdoors or spaces (crawl or attic) that freely
communicate with the outdoors.
!
154
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to supply outdoor air via grilles or ducts could result in
death and/or personal injury.
Many homes require air to be supplied from outdoors for
furnace combustion, ventilation, and dilution of flue gases.
The furnace combustion air supply must be provided in
accordance with this instruction manual.
19
352AAV
EXAMPLE: Determining Free Area
352AAV
1 SQ IN.
PER 2000
BTUH*
(305mm) 12″ MAX
A
F
1 SQ IN.
PER
4000
BTUH*
INTERIOR
HEATED
SPACE
OUTDOORS
DUCTS
TO
OUTDOORS
CIRCULATING
AIR DUCTS
B
12″ (305mm)
MAX
D
VENT
THROUGH
ROOF
CLEARANCE IN FRONT
OF COMBUSTION AIR
OPENINGS SHALL BE
AT LEAST 3 IN.
(76mm)
(305mm) 12″ MAX
1 SQ IN.
PER 2000
BTUH*
CIRCULATING AIR
DUCTS
1 SQ IN.
PER
4000
BTUH*
E
G
12″ (305mm)
MAX
C
DUCT
TO
OUTDOORS
12" MAX (305mm)
1 SQ IN.
PER 1000
BTUH* IN DOOR
OR WALL
UNCONFINED
SPACE
6" MIN (152mm)
(FRONT)Ü
1 SQ IN.
PER 1000
BTUH* IN DOOR
OR WALL
12" MAX (305mm)
12″ MAX
(305mm)
CIRCULATING AIR DUCTS
VENT THROUGH ROOF
CLEARANCE IN FRONT OF COMBUSTION AIR
OPENINGS SHALL BE AT LEAST 3 IN.
1 SQ IN.
PER 4000
BTUH*
DUCTS
TO
OUTDOORS
CIRCULATING AIR DUCTS
1 SQ IN.
PER 4000
BTUH*
* Minimum opening size is 100 sq in. (64516 mm2) with minimum dimensions of 3
in. (76 mm)
† Minimum of 3 in. (76 mm) when type-B1 vent is used.
*Minimum dimensions of 3 in. (76 mm).
Use any of the following combinations of openings:
A&BC&DD&EF&G
A03174
Fig. 18 -- Air for Combustion, Ventilation, and Dilution for
Outdoors
A03175
Fig. 19 -- Air for Combustion, Ventilation, and Dilution from
Indoors
1. For other than fan-assisted appliances, such as a draft
hood-equipped water heater:
c. Combining space on different floor levels. The
volumes of spaces on different floor levels shall be
considered as communicating spaces if connected by
one or more permanent openings in doors or floors
having free area of at least 2 in.2/1,000 Btuh
(4,400 mm2/kW) of total input rating of all
gas appliances.
2. An attic or crawlspace may be considered a space that
freely communicates with the outdoors provided there are
adequate permanent ventilation openings directly to
outdoors having free area of at least 1-in.2/4,000 Btuh of
total input rating for all gas appliances in the space.
3. In spaces that use the Indoor Combustion Air Method,
infiltration should be adequate to provide air for
combustion, permanent ventilation and dilution of flue
gases. However, in buildings with unusually tight
construction, additional air MUST be provided using the
methods described in the Outdoor Combustion Air
Method section.
Unusually
tight
construction
is
defined
as
Construction with:
a. Walls and ceilings exposed to the outdoors have a
continuous, sealed vapor barrier. Openings are
gasketed or sealed and
b. Doors and openable windows are weatherstripped and
c. Other openings are caulked or sealed. These include
joints around window and door frames, between sole
plates and floors, between wall-ceiling joints, between
wall panels, at penetrations for plumbing, electrical
and gas lines, etc.
NOTE: In determining the free area of an opening, the blocking
effect of the louvers, grilles, and screens must be considered. If
the free area of a louver or grille design is unknown, it may be
assumed that wood louvers have a 20 percent free area, and metal
louvers or grilles have a 60 percent free area. Screens, when used,
A04002
2. For fan-assisted appliances such as this furnace:
A04003
If:
Iother=combined input of all other than fan-assisted
appliances in Btu/hr
Ifan= combined input of all fan-assisted appliances in Btu/hr
ACH = air changes per hour (ACH shall not exceed 0.60.)
The following requirements apply to the Standard Method and to
the Known Air Infiltration Rate Method.
1. Adjoining rooms can be considered part of a space if:
a. There are no closable doors between rooms.
b. Combining spaces on same floor level. Each opening
shall have free area of at least 1 in.2/1,000 Btuh
(2,000 mm2/kW) of the total input rating of all gas
appliances in the space, but not less than 100 in.2
(0.06 m2). One opening shall commence within 12 in.
(305 mm) of the ceiling and the second opening shall
commence within 12 in. (305 mm) of the floor. The
minimum dimension of air openings shall be at least
3 in. (76 mm). (See Fig. 19.)
20
must not be smaller than 1/4-in. (6 mm) mesh. Louvers and
grilles must be constructed so they cannot be closed.
When combustion air ducts are used, they must be of the same
cross sectional area as the free area of the openings to which they
connect. The minimum dimension of ducts must not be less than
3 in. (76 mm).
Combination of Indoor and Outdoor Air
1. Indoor openings shall comply with the Indoor
Combustion Air Method below and,
2. Outdoor openings shall be located as required in
the Outdoor Combustion Air Method mentioned
previously and,
3. Outdoor openings shall be sized as follows:
a. Calculate the Ratio of all Indoor Space volume divided
by required volume for Indoor Combustion Air
Method below.
b. Outdoor opening size reduction Factor is 1 minus the
Ratio in a. above.
c. Minimum size of Outdoor openings shall be the size
required in Outdoor Combustion Air Method above
multiplied by reduction Factor in b. above. The
minimum dimension of air openings shall be not less
than 3 in. (76 mm).
5/ 16″
(8mm)
(8mm)
5/ 16″
1 3/4″
(44mm)
1 3/4″
(44mm)
(8mm)
5/16″
(8mm)
A89014
Fig. 20 -- Leveling Legs
!
INSTALLATION
CAUTION
UNIT MAY NOT OPERATE
Failure to follow this caution may result in intermittent unit
operation or performance satisfaction.
Step 1 -- Leveling Legs (If Desired)
When furnace is used in upflow position with side inlet(s),
leveling legs may be desired. (See Fig. 20.) Install field-supplied,
corrosion-resistant 5/16-in. (8 mm) machine bolts and nuts.
NOTE: The maximum length of bolt should not exceed 1-1/2 in
1. Position furnace on its back. Locate and drill a 5/16-in. (8
mm) diameter hole in each bottom corner of furnace. (See
Fig. 20.) Holes in bottom closure panel may be used as
guide locations.
2. For each hole, install nut on bolt and then install bolt and
nut in hole. (Install flat washer if desired.)
3. Install another nut on other side of furnace base. (Install
flat washer if desired.)
4. Adjust outside nut to provide desired height, and tighten
inside Nut to secure arrangement.
NOTE: Bottom closure must be used when leveling legs are
used. See Bottom Closure Panel section.
Do not bend duct flanges inward as shown in Fig. 21. This
will affect airflow across heat exchangers and may cause limit
cycling or premature heat exchanger failure. Remove duct
flange completely or bend it inward a minimum of 210° as
shown in Fig. 24.
Step 3 -- Installation in Horizontal Applications
These furnaces can be installed horizontally in either horizontal left
or right discharge position. In a crawlspace, the furnace can either
be hung from floor joist or installed on suitable blocks or pad.
Furnace can be suspended from each corner by hanger bolts and
angle iron supports. (See Fig. 25.) Cut hanger bolts (4 each 3/8-in.
(10 mm) all-thread rod) to desired length. Use 1 X 3/8-in. flat
washers, 3/8-in. lock washers, and 3/8-in. nuts on hanger rods as
shown in Fig. 25. Dimples are provided for hole locations. (See
Fig. 2.)
!
Step 2 -- Installation in Upflow and Downflow
Applications
CAUTION
UNIT MAY NOT OPERATE
NOTE: For downflow applications, this furnace is approved for
use on combustible flooring when special base (available from
manufacturer) Part No. KGASB0201ALL is used. Special base is
not required when this furnace is installed on manufacturer’s Coil
Assembly Part No. CD5 or CK5, or Coil Box Part No. KCAKC
is used.
1. Determine application being installed from Table 3.
2. Construct hole in floor per dimensions specified in Table 3
and Fig. 21.
3. Construct plenum to dimensions specified in Table 3
and Fig. 21.
4. If downflow subbase (KGASB) is used, install as shown in
Fig. 22. If Coil Assembly Part No. CD5 or CK5 or Coil
Box Part No. KCAKC is used, install as shown in Fig. 23.
NOTE: Remove furnace perforated, supply-air duct flanges
when they interfere with mating flanges on coil or downflow
subbase. To remove perforated, supply-air duct flanges, use wide
duct pliers, duct flange tool, or hand seamers to bend flange back
and forth until it breaks off. Be careful of sharp edges.
(See Fig. 24.)
Failure to follow this caution may result in intermittent unit
operation or performance satisfaction.
The entire length of furnace MUST be supported when
furnace is used in a horizontal position to ensure proper
draining. When suspended, bottom brace supports sides and
center blower shelf. When unit is supported from the ground,
blocks or pad should support sides and center blower
shelf area.
Step 4 -- Air Ducts
GENERAL REQUIREMENTS
The duct system should be designed and sized according to
accepted national standards such as those published by: Air
Conditioning Contractors Association (ACCA), Sheet Metal and
Air Conditioning Contractors National Association (SMACNA)
or American Society of Heating, Refrigerating and Air
Conditioning Engineers (ASHRAE), or consult The Air Systems
Design Guidelines reference tables available from your local
distributor. The duct system should be sized to handle the
required system design CFM at the design static pressure.
21
352AAV
5/ 16″
(44mm) 1 3/ 4″
3/
(44mm) 1 4″
FURNACE
(OR OTHER MANUFACTURER’S
COIL CASING WHEN USED)
A
COMBUSTIBLE
FLOORING
PLENUM
OPENING
D
B
DOWNFLOW
SUBBASE
FLOOR
OPENING
SHEET METAL
PLENUM
FLOOR
OPENING
352AAV
C
A96283
A07585
Fig. 21 -- Floor and Plenum Opening Dimensions
Fig. 22 -- Furnace, Plenum, and Subbase Installed
on a Combustible Floor
FURNACE
APPROVED
COIL ASSEMBLY
OR
COIL BOX
COMBUSTIBLE
FLOORING
SHEET METAL
PLENUM
FLOOR
OPENING
A08556
Fig. 23 -- Furnace, Plenum, and Coil Assembly or Coil Box Installed on a Combustible Floor
22
Table 3 – Opening Dimensions -- In. (mm)
PLENUM OPENING
APPLICATION
A
B
C
D
16
(406)
15-7/8
(403)
24-1/8
(613)
19
(483)
16-5/8
(422)
16-1/2
(419)
24-3/4
(629)
19-5/8
(498)
Downflow Applications on Combustible Flooring Using KGASB
Subbase Furnace with or without CAP, CAR, CNPV, CNRV Coil
Assembly or KCAKC Coil Box
15-1/8
(384)
19
(483)
16-3/4
(425)
20-3/8
(518)
Downflow Applications on Combustible Flooring NOT Using
KGASB Subbase Furnace with CAP, CAR, CNPV, CNRV Coil Assembly or KCAKC Coil Box
15-1/2
(394)
19
(483)
16-1/2
(419)
20
(508)
19-1/2
(495)
19-3/8
(492)
24-1/8
(613)
19
(483)
20-1/8
(511)
20
(508)
24-3/4
(629)
19-5/8
(498)
Downflow Applications on Combustible Flooring Using KGASB
Subbase Furnace with or without CAP, CAR, CNPV, CNRV Coil
Assembly or KCAKC Coil Box
18-5/8
(473)
19
(483)
20-1/4
(514)
20-3/8
(518)
Downflow Applications on Combustible Flooring NOT Using
KGASB Subbase Furnace with CAP, CAR, CNPV, CNRV Coil Assembly or KCAKC Coil Box
19
(483)
19
(483)
20
(508)
20
(508)
23
(584)
22-7/8
(581)
24-1/8
(613)
19
(483)
23-5/8
(600)
23-1/2
(597)
24-3/4
(629)
19-5/8
(498)
Downflow Applications on Combustible Flooring Using KGASB
Subbase Furnace with or without CAP, CAR, CNPV, CNRV Coil
Assembly or KCAKC Coil Box
22-1/8
(562)
19
(483)
23-3/4
(603)
20-3/8
(518)
Downflow Applications on Combustible Flooring NOT Using
KGASB Subbase Furnace with CAP, CAR, CNPV, CNRV Coil Assembly or KCAKC Coil Box
22-1/2
(572)
19
(483)
23-1/2
(597)
20
(508)
Upflow Applications
Downflow Applications on Non-Combustible Flooring
17-1/2
(445)
Upflow Applications
Downflow Applications on Non-Combustible Flooring
21
(533)
Upflow Applications
Downflow Applications on Non-Combustible Flooring
24-1/2
(622)
FLOOR OPENING
Flexible connections should be used between ductwork and
furnace to prevent transmission of vibration. Ductwork passing
through unconditioned space should be insulated to enhance
system performance. When air conditioning is used, a vapor
barrier is recommended.
Maintain a 1-in. (25 mm) clearance from combustible materials to
supply air ductwork for a distance of 36 in. (915 mm)
horizontally from the furnace. See NFPA 90B or local code for
further requirements.
For a furnace not equipped with a cooling coil, the outlet duct
shall be provided with a removable access panel. This opening
shall be accessible when the furnace is installed and shall be of
such a size that the heat exchanger can be viewed for possible
openings using light assistance or a probe can be inserted for
sampling the air stream. The cover attachment shall
prevent leaks.
PERFORATED
DISCHARGE DUCT
FLANGE
NO
YES
210 DEG.
MIN
DUCTWORK ACOUSTICAL TREATMENT
YES
Metal duct systems that do not have a 90 degree elbow and 10 ft
(3 M) of main duct to the first branch take-off may require
internal acoustical lining. As an alternative, fibrous ductwork
may be used if constructed and installed in accordance with the
latest edition of SMACNA construction standard on fibrous glass
ducts. Both acoustical lining and fibrous ductwork shall comply
with NFPA 90B as tested by UL Standard 181 for Class 1 Rigid
air ducts.
A93029
Fig. 24 -- Duct Flanges
When a furnace is installed so that the supply ducts carry air
circulated by the furnace to areas outside the space containing the
furnace, the return air must also be handled by a duct(s) sealed to
the furnace casing and terminating outside the space containing
the furnace.
Secure ductwork with proper fasteners for type of ductwork used.
Seal supply-and return-duct connections to furnace with code
approved tape or duct sealer.
SUPPLY AIR CONNECTIONS
Upflow Furnaces
Connect supply-air duct to 3/4-in. flange on furnace supply-air
outlet. The supply-air duct attachment must ONLY be connected
to furnace supply-/outlet-air duct flanges or air conditioning coil
casing (when used). DO NOT cut main furnace casing to attach
23
352AAV
FURNACE
CASING
WIDTH
352AAV
supply side air duct, humidifier, or other accessories. All
accessories MUST be connected external to furnace main casing.
Downflow Furnaces
Connect supply-air duct to supply-air opening on furnace. The
supply-air duct attachment must ONLY be connected to furnace
supply/outlet or air conditioning coil casing (when used), when
installed on non-combustible material. When installed on
combustible material, supply-air duct attachment must ONLY be
connected to an accessory subbase or factory approved air
conditioning coil casing. DO NOT cut main furnace casing to
attach supply side air duct, humidifier, or other accessories. All
accessories MUST be connected external to furnace main casing.
Supply air opening duct flanges must be modified per Fig. 24.
Horizontal Furnaces
Connect supply-air duct to supply air opening on furnace. The
supply-air duct attachment must ONLY be connected to furnace
supply/outlet or air conditioning coil casing (when used). DO
NOT cut main furnace casing to attach supply side air duct,
humidifier, or other accessories. All accessories MUST be
connected external to furnace main casing.
communicating with another fuel-burning appliance not of the
direct-vent type, shall be operable only when any door or panel
covering an opening in the furnace fan compartment or in a return
air plenum on ducts in the closed position.
!
WARNING
FIRE HAZARD
Failure to follow this warning could result in fire, personal
injury, or death.
Never connect return-air ducts to the back of the furnace.
Return-air duct connections on furnace side(s) permitted in
upflow applications only.
Upflow Furnaces
The return-air duct must be connected to bottom, sides (left or
right), or a combination of bottom and side(s) of main furnace
casing. Bypass humidifier may be attached into unused side
return air portion of the furnace casing. DO NOT connect any
portion of return-air duct to back of furnace casing.
Downflow and Horizontal Furnaces
The return-air duct must be connected to return-air opening
provided. DO NOT cut into casing sides or back to attach any
portion of return-air duct. Bypass humidifier connections should
be made at ductwork or coil casing sides exterior to furnace.
RETURN AIR CONNECTIONS
The furnace and its return air system shall be designed and
installed so that negative pressure created by the air circulating
fan cannot affect another appliance’s combustion air supply or act
to mix products of combustion with circulating air, and that the
air circulating fan of the furnace, if installed in an enclosure
COMBUSTION-AIR INTAKE
(NON-DIRECT VENT/1-PIPE
APPLICATION)
COMBUSTION-AIR PIPE
(DIRECT VENT/2-PIPE
APPLICATION,ALL SIZES)
VENT
3-IN. (76 mm) MINIMUM CLEARANCE TO
COMBUSTION-AIR INTAKE IS REQUIRED
(NON-DIRECT VENT/1-PIPE
APPLICATION,)
3/8-IN. (10 mm) ROD
ANGLE
IRON OR
EQUIVALENT
5 3/4″ (146 mm)
ALTERNATE SUPPORT
LOCATION 4-IN. (102 mm) MIN
8-IN. (203 mm) MAX
(B)
(A)
DRAIN
(B)
(A)
(A) ROD LOCATION
USING DIMPLE
LOCATORS
(SEE DIMENSIONAL
DWG FOR
LOCATIONS)
(B)
3/8-IN.
HEX NUT
& WASHER (4)
REQD PER ROD
(A) PREFERRED ROD LOCATION
(A)
(B)
13/16-IN.
(21 mm) MAX
ALTERNATE SUPPORT
LOCATION FROM BACK
NOTES: 1. A 1-in. (25.4 mm) clearance minimum
between top of furnace and combustible
material.
(B) ALTERNATE ROD LOCATION
2. The entire length of furnace must be
supported when furnace is used in horizontal
position to ensure proper drainage.
3. For non-direct vent/1-pipe application,
bottom side combustion-air entry cannot be
used when furnace is installed with hangers
as shown.
A05054
Fig. 25 -- Crawlspace Horizontal Application for Direct Vent/2-Pipe Installation
and for Non-Direct Vent/1-Pipe Installation
24
Step 5 -- Filter Arrangement
!
171⁄2-IN. (444mm) WIDE
CASINGS ONLY:
INSTALL FIELD-SUPPLIED
FILTER FILLER STRIP
UNDER FILTER.
WARNING
FIRE, CARBON MONOXIDE AND
POISONING HAZARD
Failure to follow this warning could result in fire, personal
injury or death.
Never operate unit without a filter or with filter access
door removed.
21-IN. (533mm) WIDE
CASINGS ONLY:
SUPPORT RODS (3)
EXTEND 1/4" (6mm) ON
EACH SIDE OF FILTER AND
REST ON CASING FLANGE
3″
(76mm)
24 1/2″
(533mm)
1″
(25.4mm)
352AAV
The air filter arrangement will vary due to application, furnace
orientation, and filter type. The filter may be installed in an
external Filter/Media cabinet (if provided) or the furnace blower
compartment.
If a factory-supplied external Filter/Media cabinet is provided,
instructions for its application, assembly, and installation are
packaged with the cabinet. The Filter/Media cabinet can be used
with a factory--specified washable filter or a factory-specified
high-efficiency disposable filter (see cabinet instructions).
If installing the filter in the furnace blower compartment,
determine location for filter and relocate filter retaining wire if
necessary. See Table 4 to determine correct filter size for desired
filter location. Table 4 indicates filter size and location for this
furnace. See Fig. 2 for location and size of bottom and side
return-air openings.
FILTER
Table 4 – Filter Information
AIR FILTER LOCATED IN BLOWER COMPARTMENT
Furnace
Filter Size --- In. (mm)
Casing
Filter Type
Width
Framed
Side Return*{
Bottom Return*
In. (mm)
17 --- 1/2
(445)
(1) 16 X 25 X 3/4
(406 X 635 X 19)
(1) 16 X 25 X 3/4
(406 X 635 X 19)
Washable
21
(533)
(1) 16 X 25 X 3/4
(1) 20 X 25 X 3/4
Washable
(406 X 635 X 19)
(508 X 635 X 19)
(1 or 2) 16 X 25
24---1/2
(1) 24 X 25 X 3/4
X 3/4
Washable
(622)
(609 X 635 X 19)
(406 X 635 X 19)
*Alternate sizes can be ordered from your distributor or dealer.
{ Upflow only. Alternate sizes and additional filters may be ordered from
your dealer.
FILTER
SUPPORT
FILTER
RETAINER
A08605
Fig. 27 -- Bottom Filter Arrangement
FILTER
FILTER
RETAINER
BOTTOM
CLOSURE
PANEL
FRONT FILLER
PANEL
A08587
Fig. 26 -- Filter Installed for Side Inlet
A93047
Fig. 28 -- Removing Bottom Closure Panel
25
!
Risers must be used to connect to furnace and to meter. Support
all gas piping with appropriate straps, hangers, etc. Use a
minimum of 1 hanger every 6 ft. (2 M). Joint compound (pipe
dope) should be applied sparingly and only to male threads of
joints. Pipe dope must be resistant to propane gas.
CAUTION
CUT HAZARD
Failure to follow this caution may result in minor
personal injury.
Use care when cutting support rods in filters to protect against
flying pieces and sharp rod ends. Wear safety glasses, gloves,
and appropriate protective clothing.
!
!
CAUTION
352AAV
UNIT MAY NOT OPERATE
--Gas valve shutoff switch MUST be facing forward or tilted
upward.
Failure to follow this caution may result in intermittent unit
operation or performance satisfaction.
For airflow requirements above 1800 CFM, see Air Delivery
table in Product Data literature for specific use of single side
inlets. The use of both side inlets, a combination of 1 side and
the bottom, or the bottom only will ensure adequate return air
openings for airflow requirements above 1800 CFM.
--Never purge a gas line into a combustion chamber. Never test
for gas leaks with an open flame. Use a commercially
available soap solution made specifically for the detection of
leaks to check all connections.
--Use proper length of pipe to avoid stress on gas control
manifold.
--If a flexible connector is required or allowed by authority
having jurisdiction, black iron pipe shall be installed at furnace
gas valve and extend a minimum of 2 in. (51 mm) outside
furnace casing.
NOTE: Side return-air openings can ONLY be used in
UPFLOW configurations. Install filter(s) as shown in Fig. 26.
Bottom return-air opening may be used with all 4 orientations.
Filter may need to be cut to fit some furnace widths. Install filter
as shown in Fig. 27.
NOTE: Remove and discard bottom closure panel when bottom
inlet is used.
--Protect gas valve from water and debris. Gas valve inlet
and/or inlet piping must remain capped until gas supply line is
permanently installed to protect the valve from moisture and
debris. Also, install a sediment trap in the gas supply piping at
the inlet to the gas valve.
Step 6 -- Bottom Closure Panel
This furnace is shipped with bottom closure panel installed in
bottom return-air opening. This panel MUST be in place when
side return air is used.
To remove bottom closure panel, perform the following:
1. Tilt or raise furnace and remove 2 screws holding front
filler panel. (See Fig. 28.)
2. Rotate front filler panel downward to release holding tabs.
3. Remove bottom closure panel.
4. Reinstall front filler panel and screws.
Install a sediment trap in riser leading to furnace. Trap can be
installed by connecting a tee to riser leading to furnace so
straight-through section of tee is vertical. Then connect a capped
nipple into lower end of tee. Capped nipple should extend below
level of gas controls. Place a ground joint union between gas
control manifold and manual gas shutoff valve. (See Fig. 29.)
GAS
SUPPLY
MANUAL
SHUTOFF
VALVE
(REQUIRED)
Table 5 – Maximum Capacity of Pipe*
NOMINAL
IRON PIPE
SIZE
IN. (MM)
INTERNAL
DIA.
IN. (MM)
1/2 (12.7)
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow this warning could result in fire, personal
injury or death.
--Connect gas pipe to furnace using a backup wrench to avoid
damaging gas controls.
LENGTH OF PIPE --- FT (M)
10
(3.0)
20
(6.0)
30
(9.1)
40
(12.1)
50
(15.2)
0.622
(158)
175
120
97
82
73
3/4 (19.0)
0.824
(20.9)
360
250
200
170
151
1 (25.4)
1.049
(26.6)
680
465
375
320
285
1-1/4
(31.8)
1.380
(35.0)
1400
950
770
660
580
1-1/2
(38.1)
1.610
(40.9)
2100
1460
1180
990
900
SEDIMENT
TRAP
UNION
* Cubic ft of gas per hr for gas pressures of 0.5 psig (14---in. wc) or less and
a pressure drop of 0.5---in wc (based on a 0.60 specific gravity gas). Ref:
Table 9.2 NFGC.
A93324
Step 7 -- Gas Piping
Fig. 29 -- Typical Gas Pipe Arrangement
Gas piping must be installed in accordance with national and
local codes. Refer to current edition of NFGC in the
United States.
Canadian installations must be made in accordance with
NSCNGPIC and all authorities having jurisdiction.
Gas supply line should be a separate line running directly from
meter to furnace, if possible. Refer to Table 5 for recommended
gas pipe sizing.
If local codes allow the use of a flexible gas appliance connector,
always use a new listed connector. Do not use a connector which
has previously served another gas appliance.
An accessible manual shutoff valve MUST be installed external
to furnace casing and within 6 ft (2 M)of furnace. A 1/8-in. NPT
plugged tapping, accessible for test gauge connection, MUST be
installed immediately upstream of gas supply connection to
furnace and downstream of manual shutoff valve.
26
Table 6 – Electrical Data
UNIT SIZE
VOLTSHERTZPHASE
060–12 / 036060
080–12 / 036080
080–16 / 048080
100–16 / 048100
100–20 / 060100
120–20 / 060120
115---60---1
115---60---1
115---60---1
115---60---1
115---60---1
115---60---1
OPERATING VOLTAGE
RANGE
Max*
Min*
MAX
UNIT
AMPS
127
127
127
127
127
127
104
104
104
104
104
104
8.4
8.1
11.6
11.6
13.3
12.9
UNIT
AMPACITY†
MIN
WIRE
SIZE
MAX WIRE
LENGTH
FT (M)‡
11.3
10.8
15.3
15.4
17.5
16.8
14
14
12
12
12
12
33 (10.0)
34 (10.3)
37 (11.2)
37 (11.2)
33 (10.0)
34 (10.3)
MAX FUSE
OR CKT
BKR
AMPS**
15
15
20
20
20
20
* Permissible limits of voltage range at which unit will operate satisfactorily.
† Unit ampacity = 125 percent of largest operating component’s full load amps plus 100 percent of all other potential operating components’ (EAC, humidifier,
etc.) full load amps.
‡ Length shown is measured 1 way along wire path between unit and service panel for maximum 2 percent voltage drop.
** Time-delay type is recommended.
!
See Fig. 31, 32, and 50--57 for field wiring diagram showing
typical field 115-v and 24-v wiring. Check all factory and field
electrical connections for tightness.
!
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
Blower access door switch opens 115-v power to furnace
control. No component operation can occur. Do not bypass or
close switch with panel removed.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow this warning exactly could result in serious
injury, death, or property damage.
Never test for gas leaks with an open flame. Use a
commercially available soap solution made specifically for the
detection of leaks to check all connections. A fire or explosion
could result causing property damage, personal injury or loss
of life.
Field-supplied wiring shall conform with the limitations of
63°F (35°C) rise.
!
Failure to follow this caution may result in intermittent
unit operation.
Furnace control must be grounded for proper operation or
control will lock out. Control is grounded through
green/yellow wire routed to gas valve C-terminal and burner
box screw.
115-V WIRING
Before proceeding with electrical connections, make certain that
voltage, frequency, and phase correspond to that specified on the
furnace rating plate. Also, check to be sure that service provided
by power supply is sufficient to handle load imposed by this
equipment. Refer to rating plate or Table 6 for equipment
electrical specifications.
The furnace must be electrically grounded in accordance with
local codes; or in the absence of local codes, with the National
Electric Code ANSI/NFPA 70 and/or the Canadian Electric Code,
CSA C22.1, Part I, if an external electrical source is utilized.
COMBUSTION-AIR PIPE GROMMET
UNUSED 1-3/4 -IN. (44 mm)
DIAMETER GAS
CONN. HOLE
GAS LINE
GAS LINE ENTRY
HOLE FILLER PLUG
VENT PIPE
GAS LINE GROMMET
VENT PIPE GROMMET
NOTE: PIPE GROMMETS AND ENTRY HOLE FILLER
PLUGS ARE INCLUDED IN FACTORY-SUPPLIED
LOOSE PARTS BAG
A05057
Fig. 30 -- Typical Gas Pipe Arrangement
CAUTION
UNIT MAY NOT OPERATE
Gas line grommet (factory-supplied loose parts bag) should be
used when installing gas piping. Gas line entry hole filler plug
should be installed in unused gas line entry hole. (See Fig. 30.)
NOTE: The gas valve inlet pressure tap connection is suitable to
use as test gauge connection providing test pressure DOES NOT
exceed maximum 0.5 psig (14-in. wc) stated on gas valve. (See
Fig. 58.)
The gas supply pressure shall be within the maximum and
minimum inlet supply pressures marked on the rating plate with
the furnace burners ON at HI-HEAT and OFF.
COMBUSTION
-AIR PIPE
WARNING
A05057
27
352AAV
Step 8 -- Electrical Connections
Piping should be pressure tested in accordance with the current
edition of the NFGC, local and national plumbing and gas codes
before the furnace has been connected. In Canada, refer to current
edition of NSCNGPIC. If the pressure exceeds 0.5 psig (14-in.
wc), gas supply pipe must be disconnected from the furnace and
capped before pressure test. If test pressure is equal to or less than
0.5 psig (14-in. wc), turn off electric shutoff switch located on
furnace gas valve and accessible manual shutoff valve before test.
After all connections have been made, purge lines and check for
leakage.
FIELD 24-V WIRING
FIELD 115-, 208/230-, 460-V WIRING
FACTORY 24-V WIRING
FACTORY 115-V WIRING
1-STAGE THERMOSTAT TERMINALS
W
FIVE
WIRE
Y
R
G
C
FIELD-SUPPLIED
FUSED DISCONNECT
TWO-WIRE
HEATINGONLY
BLK
BLK
WHT
WHT
208/230- OR
460-V
THREE
PHASE
W2
GND
GND
COM
208/230-V
SINGLE
PHASE
W/W1
GND
352AAV
GND
Y/Y2
115-V FUSED
DISCONNECT
SWITCH
(WHEN REQUIRED)
JUNCTION
BOX
CONTROL
BOX
GND
R
GND
CONDENSING
UNIT
G
24-V
TERMINAL
BLOCK
FURNACE
NOTES: 1. Connect Y-terminal as shown for proper operation.
2. Some thermostats require a "C" terminal connection as shown.
3. If any of the original wire, as supplied, must be replaced,
use same type or equivalent wire.
A99071
Fig. 31 -- Typical Heating and Cooling Application Wiring Diagram 1-Stage Thermostat and Condensing Unit
FIELD 24-V WIRING
FIELD 115-, 208/230-, 460-V WIRING
FACTORY 24-V WIRING
FACTORY 115-V WIRING
2-STAGE THERMOSTAT TERMINALS
SEVEN
WIRE
W2
W1
Y2
R
G
Y1
C
FIELD-SUPPLIED
FUSED DISCONNECT
THREE-WIRE
HEATINGONLY
W2
BLK
BLK
WHT
208/230- OR
460-V
THREE
PHASE
GND
GND
COM
WHT
208/230-V
SINGLE
PHASE
W/W1
GND
GND
C
Y/Y2
115-V FUSED
JUNCTION
DISCONNECT
BOX
SWITCH
CONTROL
(WHEN REQUIRED)
BOX
Y1
Y2
R
24-V
TERMINAL
BLOCK
FURNACE
GND
GND
2-SPEED
CONDENSING
UNIT
G
NOTES: 1. Connect Y-terminal as shown for proper operation.
2. Some thermostats require a "C" terminal connection as shown.
3. If any of the original wire, as supplied, must be replaced,
use same type or equivalent wire.
A99072
Fig. 32 -- Typical Heating and Cooling Application Wiring Diagram 2-Stage Thermostat and Condensing Unit
28
FACTORY
INSTALLED
LOCATION
ELECTRIC
DISCONNECT
SWITCH
COPPER
WIRE ONLY
POWER ENTRY HOLE
FILLER PLUG (FACTORYSUPPLIED LOOSE PARTS BAG)
UNUSED 7/8-IN. (22 mm)
DIAMETER POWER
ENTRY HOLES
ALUMINUM
WIRE
A93033
A05113
Fig. 33 -- Disconnect Switch and Furnace
Fig. 34 -- Factory Installed J-Box Location
!
Make field 24-v connections at 24-v terminal block on furnace.
(See Fig. 37.) Connect terminal Y/Y2 as shown in Fig. 31 and 32
for proper cooling operation. Use only AWG No. 18, color-coded,
copper thermostat wire for lengths up to 100 ft. (30 M). For wire
lengths over 100 ft. (30 M), use AWG No. 16 wire.
The 24-v circuit contains an automotive-type, 3-amp fuse located
on furnace control. (See Fig. 37.) Any direct shorts of 24-v wiring
during installation, service, or maintenance could cause this fuse
to blow. If fuse replacement is required, use ONLY a 3-amp fuse
of identical size/type. The control will flash code 24 when fuse
needs replacement.
WARNING
FIRE HAZARD
Failure to follow this warning could result in intermittent
operation or performance satisfaction.
Do not connect aluminum wire between disconnect switch and
furnace. Use only copper wire. (See Fig. 33.)
!
ACCESSORIES
1. Electronic Air Cleaner (EAC) Two male quick-connect
terminals marked EAC-1 and EAC-2 are provided for
EAC connection. (See Fig. 37.) These terminals are
energized with 115-v (1.0-amp maximum) during blower
motor operation.
2. Humidifier (HUM) Connect an accessory 24 VAC, 0.5
amp maximum humidifier (if used) to the 1/4-in. male
quick-connect HUM terminal and COM-24V screw
terminal on the control board thermostat strip. The HUM
terminal is energized when gas valve is energized. (See
Fig. 36 or 37.)
NOTE: A field-supplied, 115–v controlled relay connected to
EAC terminals may be added if humidifier operation is desired
during blower operation.
WARNING
ELECTRICAL SHOCK AND FIRE HAZARD
Failure to follow this warning could result in electrical shock,
fire, or death.
The furnace casing MUST have an uninterrupted or unbroken
ground according to NEC ANSI/NFPA 70--2008 and Canadian
Electrical Code CSA C22.1 or local codes to minimize
personal injury if an electrical fault should occur. This may
consist of electrical wire or conduit approved for electrical
ground when installed in accordance with existing electrical
codes. Do not use gas piping as an electrical ground.
!
UNIT DAMAGE HAZARD
Factory Installed J-Box Location
Install electrical entry hole filler plugs (factory-supplied in loose
parts bag) in unused power entry holes. (See Fig. 34.)
J-Box Relocation
1. Remove 2 screws holding auxiliary J-box. (See Fig. 35.)
2. Rotate J-box 180° and attach box to left side, using
holes provided.
3. Install electrical entry hole filler plugs (factory-supplied
loose parts Bag) in unused power entry holes. (See Fig.
35.)
!
CAUTION
Failure to follow
component damage.
this
caution
may
result
in
unit
DO NOT connect furnace control HUM terminal to HUM
(humidifier) terminal on Thermidistatt, Zone Controller or
similar device. See Thermidistatt, Zone Controller,
thermostat, or controller manufacturer’s instructions for
proper connection.
WARNING
ELECTRICAL SHOCK AND FIRE HAZARD
Failure to follow this warning could result in intermittent unit
operation or performance satisfaction.
If manual disconnect switch is to be mounted on furnace,
select a location where a drill or fastener will not contact
electrical or gas components.
29
352AAV
24-V WIRING
Use a separate, fused branch electrical circuit containing a
properly sized fuse or circuit breaker for this furnace. See Table 6
for wire size and fuse specifications. A disconnecting means must
be located within sight from and readily accessible to furnace.
NOTE:
Proper polarity and proper grounding must be
maintained for 115-v wiring. If polarity is incorrect, control LED
status indicator light will flash rapidly and furnace will
NOT operate.
ALTERNATE
FIELD
LOCATION
FACTORY
INSTALLED
LOCATION
POWER ENTRY HOLE
FILLER PLUG (FACTORYSUPPLIED LOOSE PARTS BAG)
POWER ENTRY HOLE
FILLER PLUG (FACTORYSUPPLIED LOOSE PARTS BAG)
UNUSED 7/8-IN. (22 mm) DIAMETER
POWER ENTRY HOLES
352AAV
UNUSED 7/8-IN. (22 mm) DIAMETER
POWER ENTRY HOLES
A05058
Fig. 35 -- Relocating J-Box
Step 9 -- Removal of Existing Furnaces from
Common Vent Systems
!
When an existing Category I furnace is removed or replaced, the
original venting system may no longer be sized to properly vent
the remaining attached appliances. An improperly sized
Category I venting system could cause the formation of
condensate in the furnace and vent, leakage of condensate and
combustion products, spillage of combustion products into the
living space, etc.
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow the steps outlined below for each appliance
connected to the venting system being placed into operation
could result in carbon monoxide poisoning or death.
The following steps shall be followed for each appliance
connected to the venting system being placed into operation,
while all other appliances connected to the venting system are
not in operation:
1. Seal any unused openings in venting system.
2. Inspect the venting system for proper size and horizontal
pitch, as required in the National Fuel Gas Code, ANSI
Z223.1--2006/NFPA 54--2006 or the CSA B149.1--05,
Natural Gas and Propane Installation Code and these
instructions. Determine that there is no blockage or
restriction, leakage, corrosion and other deficiencies,
which could cause an unsafe condition.
3. As far as practical, close all building doors and windows
and all doors between the space in which the appliance(s)
connected to the venting system are located and other
spaces of the building.
4. Close fireplace dampers.
5. Turn on clothes dryers and any appliance not connected to
the venting system. Turn on any exhaust fans, such as
range hoods and bathroom exhausts, so they are operating
at maximum speed. Do not operate a summer exhaust fan.
6. Follow the lighting instructions. Place the appliance being
inspected into operation. Adjust the thermostat so
appliance is operating continuously.
7. Test for spillage from draft hood equipped appliances at
the draft hood relief opening after 5 minutes of main
burner operation. Use the flame of a match or candle.
8. If improper venting is observed during any of the above
tests, the venting system must be corrected in accordance
with the National Fuel Gas Code, ANSI
Z223.12006/NFPA 54--2006 and/or CSA B149.1--05,
Natural Gas and Propane Installation Code.
9. After it has been determined that each appliance
connected to the venting system properly vents when
tested as outlined above, return doors, windows, exhaust
fans, fireplace dampers and any other gas-fired burning
appliance to their previous conditions of use.
Step 10 -- Combustion Air and Vent Pipe Systems
GENERAL
Vent system or vent connectors may need to be resized. For any
other appliances when resizing vent systems or vent
connectors, system or connector must be sized to approach
minimum size as determined using appropriate table found in the
NFGC or NSCNGPIC.
The 352AAV can be vented as either a direct vent (all sizes) or as
a non-direct vent (except for 140 size) application. A direct vent
system shall be installed in accordance with the direct vent
(2-pipe) procedures in the following Combustion Air and
Vent Pipe Systems section. For non-direct vent (1-pipe)
applications, refer to the non-direct vent (1-pipe) procedures in
the same section.
Multistory and common venting are prohibited.
DIRECT VENT/2-PIPE SYSTEM
In a direct-vent (2-pipe) system, all air for combustion is taken
directly from outdoor atmosphere, and all flue products are
discharged to outdoor atmosphere. A factory accessory vent
termination kit MUST be used in a direct vent (2-pipe) system.
NON-DIRECT VENT/1-PIPE SYSTEM
In a non-direct vent (1-pipe) system, all air for combustion is
taken from the area adjacent to furnace, and all flue products are
discharged to outdoor atmosphere. A factory-supplied perforated
disk assembly (in loose parts bag) MUST be used in
combustion-air pipe elbow.
MATERIALS
Combustion-air and vent pipe, fittings, primers, and solvents
must conform to American National Standards Institute (ANSI)
standards and American Society for Testing and Materials
(ASTM) standards. See Table 7 for approved materials for use in
the U.S.A.
30
BRN
GRN/YEL
BRN
HI
1 2 3
BLU
31
LEGEND
Fig. 36 -- Wiring Diagram
GND
GV
GVR 1, 2
HPS
HPSR
HSI
HSIR
HUM
IDM
IDR
IHI/LOR
ILK
JB
LED
LGPS
LPS
LS
OL
PCB
ACR
ACRDJ
BHI/LOR
BHT/CLR
BLWR
BLWM
CAP 1, 2
CPU
DHUM
EAC-1
EAC-2
FRS
FSE
FU1
FU2
PLT
ACRDJ
GRY
HPS
RED
PL1
STATUS CODE
LED
1
WHT
YEL
RED
LPS
LS
NOTE #8
AIR CONDITIONING RELAY, SPST (N.O.)
AIR CONDITIONING RELAY DISABLE JUMPER
BLOWER MOTOR SPEED CHANGE RELAY, SPDT
BLOWER MOTOR SPEED CHANGE RELAY, SPDT
BLOWER MOTOR RELAY, SPST-(N.O.)
BLOWER MOTOR, PERMANENT-SPLIT-CAPACITOR
CAPACITOR
MICROPROCESSOR AND CIRCUITRY
DHUM CONNECTION
ELECTRONIC AIR CLEANER CONNECTION (115 VAC 1.0 AMP MAX.)
ELECTRONIC AIR CLEANER CONNECTION (COMMON)
FLAME ROLLOUT SW. -MANUAL RESET, SPST-(N.C.)
FLAME-PROVING ELECTRODE
FUSE, 3 AMP, AUTOMOTIVE BLADE TYPE, FACTORY INSTALLED
FUSE OR CIRCUIT BREAKER CURRENT INTERRUPT DEVICE
(FIELD SUPPLIED AND INSTALLED)
EQUIPMENT GROUND
GAS VALVE-REDUNDANT
GAS VALVE RELAY, DPST-(N.O.)
HIGH-HEAT PRESSURE SWITCH, SPST (N.O.)
HIGH-HEAT PRESSURE SWITCH RELAY, SPST (N.C.)
HOT SURFACE IGNITER (115VAC)
HOT SURFACE IGNITER RELAY, SPST (N.O.)
24VAC HUMIDIFIER CONNECTION (0.5 AMP. MAX.)
INDUCED DRAFT MOTOR, 2-SPEED, SHADED POLE
INDUCED DRAFT MOTOR RELAY, SPST-(N.O.)
INDUCER MOTOR SPEED CHANGE RELAY, SPDT
BLOWER ACCESS PANEL INTERLOCK SWITCH, SPST-(N.O.)
JUNCTION BOX
LIGHT-EMITTING DIODE FOR STATUS CODES - AMBER
LOW GAS PRESSURE SWITCH, SPST-(N.O.)
LOW-HEAT PRESSURE SWITCH, SPST (N.O.)
LIMIT SWITCH, AUTO-RESET, SPST (N.C.)
AUTO-RESET INTERNAL MOTOR OVERLOAD TEMPERATURE SWITCH (N.C.)
PRINTED CIRCUIT BOARD CONTROL
Y1 DHUM G Com W/W1 Y/Y2 R
24V
LHT
OFF
DLY
W2
ON
OFF
TEST/TWIN
SELECT CHART
BLOWER
SW LO-HT OFF-DELAY
ONLY
1 *
2 3
90
ON NORM
SEC.
OFF HEAT
1 LO 2 3 *
120
ON
HEAT
SEC.
OFF ONLY
2 3
ON
150
OFF
SEC.
2 3
ON
180
OFF
SEC.
* FACTORY SETTINGS
C
GV
WHT
GRN/YEL
0.5 AMP
@ 24 VAC
WHT
FUSE 3-AMP
FU1
NOTE #6
FRS
IDR
HSIR
IHI/LOR
L1
NOTE #11
RED
PL1
PL2
PL3
PL4
PL5
PLT
TRAN
TEST/TWIN
PL2
CAP-2
BRN
IDM
WHT
BLK
YEL
ORN
BLU
RED
OL
RED
BLU
BLK
BRN
WHT
BRN
START
PL5
HSI
JUNCTION
FIELD EARTH GROUND
326797-101 REV. A
PLUG RECEPTACLE
FIELD SPLICE
EQUIPMENT GROUND
TRAN
ACR
PCB
COM 24V
Y1
G
Y/Y2
W2
DHUM
TEST/TWIN
W/W1
R
HUM
NOTE #5
L1
IDR
HSIR
IHI/LOR
L2
L2
1
3
2
NOTE #2
PL2
BHI/LOR
LO HEAT
EQUIPMENT
GROUND
1
2
PL5
HSI
PL4
CPU
GVR-2
FRS
EAC-1
GVR-1
HPSR
LS
PL1-7
PL1-11
PL1-9
PL1-1
CAP-1
LPS
C
FSE
PL1-5
HI
L2
24VAC SEC 2
SEC 1 TRAN
NOTE #11
GV
L2
L2
PR1 115VAC
START
BLWM
IDM
OL
LGPS
(WHEN USED)
HPS
PL1-10 M
PL1-3
PL1-4
PL1-2
PL1-12
PL1-8
NOTE #6
FU1
COM
NOTE #3
PL1-6
EAC-2
OL
4 LO
COM
3
HI
1
2
SCHEMATIC DIAGRAM
(NATURAL GAS & PROPANE)
LO
SPARE-1 MED LO
NOTE #10
BHT/CLR
MED
HI HEAT
SPARE-2
MED HI
COOLING
BLWR
HI
NOTE #9
ILK
TO 115VAC FIELD-DISCONNECT SWITCH
A02176
352AAV
If any of the original equipment wire is replaced use wire rated for 105°C.
Use only copper wire between the disconnect switch and the furnace junction box (JB).
This wire must be connected to furnace sheet metal for control to prove flame.
Symbols are electrical representation only.
Solid lines inside PCB are printed circuit board conductors and are not included in the legend.
Replace only with a 3 amp fuse.
Blower motor (BLWM) and inducer motor (IDM) contain internal auto-reset thermal overload switches (OL).
Neutral connections are interchangeable within the NEUTRAL connector block.
Blower motor speed selections are for average conditions, see installation instructions for optimum selection.
MED not available on some models.
Factory connected when LGPS is not used.
Ignition lockout will occur after four consecutive unsuccessful trials-for-ignition. Control will auto-reset after
three hours.
13. Blower-on delay: gas high-heat 60 seconds, gas low-heat 45 seconds, cooling or heat pump 2 seconds.
14. Blower off-delay: gas heating selections are 90, 120, 150, 180 seconds, cooling or heat pump 90 seconds or
5 seconds when dehumidify call is active.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
NOTES:
CAP-1
ILK
JB
GND
PRINTED CIRCIUT BOARD
FIELD WIRING SCREW TERMINAL
CONDUCTOR ON CONTROL PCB
FIELD CONTROL WIRING (24VAC)
FIELD CONTROL WIRING (115VAC)
FACTORY CONTROL WIRING (24VAC)
FACTORY POWER WIRING (115VAC)
CONTROL PCB TERMINAL
TERMINAL
FU2
L1 NOTE #2
WHT BLK
NEUTRAL
FUSE OR CIRCUIT
BREAKER & DISCONNECT
SWITCH (WHEN REQ’D)
BLWM
OL
2
1
GRN /YEL
2 3
4
BRN
IDM
WHT
12-CIRCUIT PCB CONNECTOR
3-CIRCUIT PCB HSI & IDM CONNECTOR
6-CIRCUIT ICM MOTOR CONNECTOR (NOT SHOWN)
4-CIRCUIT IDM CONNECTOR
2-CIRCUIT HSI CONNECTOR
3-CIRCUIT FACTORY TEST CONNECTOR
TRANSFORMER, 115VAC/24VAC
COMPONENT TEST & TWINNING TERMINAL
WHT
HI
MED HI
MED
MED LO
LO
BLK
WHT
PL3
1
RED
BLK
GRN/YEL
BLK
BLK
RED
WHT
FSE
ORN
LGPS (WHEN USED)
SPARE - 1
GRN/YEL
M
HUM
SEC-1
SEC-2
CAP-2
CONNECTION DIAGRAM
NEUTRAL - L2
EAC-2
BLWR
BHT/CLR
BLW
BHI/LOR
HI-HEAT
COOL
LO-HEAT
PR-1
SPARE-2
HSI HI LO
EAC-1
1 AMP
@ 115 VAC
NOTE #3
PRINTED CIRCIUT BOARD
ACRDJ
352AAV
Table 7 – Approved Combustion-Air and Vent Pipe, Fitting and Cement Materials (USA only*)
ASTM
SPECIFICATION
(MARKED ON
MATERIAL)
MATERIAL
PIPE
FITTINGS
SOLVENT CEMENT
AND PRIMERS
D1527
D1785
D2235
D2241
D2466
D2468
D2564
D2661
D2665
F438
F441
F442
F493
ABS
PVC
For ABS
PVC
PVC
ABS
For PVC
ABS
PVC
CPVC
CPVC
CPVC
For CPVC
Pipe
Pipe
--- --Pipe
--- ----- ----- --Pipe
Pipe
--- --Pipe
Pipe
--- ---
--- ----- ----- ----- --Fittings
Fittings
--- --Fittings
Fittings
Fittings
--- ----- ----- ---
--- ----- --Solvent Cement
--- ----- ----- --Solvent Cement
--- ----- ----- ----- ----- --Solvent Cement
F628
ABS
Pipe
--- ---
--- ---
Schedule---40
Schedule---40
For ABS
SDR---21 & SDR---26
Schedule---40
Schedule---40
For PVC
DWV at Schedule---40 IPS sizes
DWV
Schedule---40
Schedule---40
SDR
For CPVC
Cellular Core DWV at Schedule---40
IPS sizes
F656
F891
For PVC
PVC
--- --Pipe
--- ----- ---
Primer
--- ---
For PVC
Cellular Core Schedule---40 & DWV
*Refer to Page 1 for Canadian installations.
!
DESCRIPTION
Other gas appliances with their own venting system may also use
the abandoned chimney as a raceway providing it is permitted by
local code, the current edition of the National Fuel Gas Code and
the vent or liner manufacturer’s installation instructions. Care
must be taken to prevent the exhaust gases from one appliance
from contaminating the combustion air of other gas appliances.
WARNING
FIRE AND EXPLOSION HAZARD
Failure to follow this warning could result in fire, property
damage, personal injury, or death. Solvent cements are
combustible. Keep away from heat, sparks, and open flame.
Use only in well-ventilated areas. Avoid breathing in vapor or
allowing contact with skin or eyes.
!
CAUTION
UNIT MAY NOT OPERATE
Failure to follow this caution may result in intermittent
unit operation.
In Canada, construct all combustion-air and vent pipes for this
unit of CSA or ULC listed schedule-40 PVC, PVC-DWV or
ABS-DWV pipe and pipe cement. SDR pipe is NOT approved in
Canada.
In direct vent (2-pipe) systems, combustion air and vent pipes
must terminate together in same atmospheric pressure zone,
either through roof or sidewall (roof termination preferred), using
accessory termination kit. See Table 8 for required clearances.
In non-direct vent (1-pipe) system, vent pipe termination must be
installed with adequate clearances to building openings and
equipment to comply with national and local codes. See Table 9
for required clearances.
!
When vent pipe is exposed to temperatures below freezing,
such as when it passes through an unheated space or when a
chimney is used as a raceway, pipe must be insulated as
shown in Table 10 with Armaflex-type insulation.
Furnace combustion air and vent pipe connections are sized for
2-in. (51 mm) pipe. Any pipe size change should be made outside
furnace casing in vertical pipe. The transition has to be made as
close to the furnace as reasonably possible.
COMBUSTION AIR PIPE
General
Furnace combustion-air connection must be attached as shown in
Fig. 38. Combustion-air intake housing plug may need to be
relocated in some applications.
For Non-Direct Vent (1-Pipe) system, combustion-air must
terminate outside of furnace casing with 1 elbow. Orient elbow so
that its opening faces down for upflow or downflow applications.
Orient elbow so that its opening faces sideways (left or right) for
horizontal left or horizontal right applications. Maintain a 3-in
minimum clearance between the opening of the combustion-air
inlet pipe and any object.
WARNING
CARBON MONOXIDE POISONING HAZARD
Failure to follow this warning could result in property damage,
personal injury, or death.
All combustion-air and vent pipes must be airtight and
watertight. Pipes must also terminate exactly as shown in Fig.
44 for direct vent (2-pipe) system and Fig. 45 for non-direct
vent (1-pipe) system.
An abandoned masonry chimney may be used as a raceway for
properly insulated and supported combustion-air (when
applicable) and vent pipes. Each furnace must have its own set of
combustion-air and vent pipes and be terminated individually, as
shown in Fig. 44 for Direct Vent (2-Pipe) system and Fig. 45 for
Non-Direct Vent (1-Pipe) system.
A furnace shall not be connected to a chimney flue serving a
separate appliance designed to burn solid fuel.
32
SETUP SWITCHES
LOW-HEAT ONLY AND
BLOWER OFF-DELAY
TWINNING AND/OR
COMPONENT TEST
TERMINAL
PLT
HUM
TRANSFORMER 24-VAC
CONNECTIONS
0.5-AMP024 VAC
R
LE
SEC-2
PL3
NEUTRAL-L2
PL1
OD E
EAC-2
D
SEC-1
352AAV
PL1 - LOW VOLTAGE MAIN
HARNESS CONNECTOR
FUSE 3-AMP
US C
3-AMP FUSE
ACRDJ
TEST/TWIN
STAT
LED OPERATION &
DIAGNOSTIC LIGHT
1 2 3
LHT
OFF
DLY
Y1 DHUM G COM WW1 Y/Y2
24V
HUMIDIFIER TERMINAL
(24-VAC 0.5 AMP MAX.)
ON
OFF
W2
24-V-THERMOSTAT
TERMINALS
ACRDJ - AIR CONDITIONING
RELAY DISABLE JUMPER
PL3
1
1
BLW
115-VAC (L2) NEUTRAL
CONNECTIONS
BHI/LOR
BHT/CLR
BLWR
HI HEAT
IDM
COOL
IHI/LOR
SPARE-2
PR-1
PL2
EAC-1
1
SPARE-2
L1
1-AMP@115 VAC
COOL
SPARE-1
SPARE-1
BLOWER SPEED
SELECTION TERMINALS
HSIR
IDR
LO HEAT
HI HEAT
LO HEAT
HSI
HI LO
115-VAC (L1) LINE
VOLTAGE CONNECTION
PL2 - HOT SURFACE
IGNITER & INDUCER
MOTOR CONNECTOR
EAC-1 TERMINAL
(115-VAC 1.0 AMP MAX.)
A02017
Fig. 37 -- Control Center
!
4. Permanently attach elbow/perforated disk assembly to
straight portion of pipe using RTV or by cementing as
shown in Fig. 39.
Assembly of Combustion Air Pipe (Direct Vent-2-Pipe
System ONLY)
1. Using Table 13, determine the smallest combustion air
diameter permitted. Pick the larger diameter and use it for
both combustion and vent pipe.
NOTE: Do not count elbows or pipe sections in terminations or
within furnace (All elbows shown in Fig. 44 and Fig. 45 are not
to be counted).
CAUTION
UNIT CORROSION HAZARD
Excessive exposure to contaminated combustion air may result
in safety and performance related problems.
Combustion air must not be taken from inside structure
because inside air is frequently contaminated by halogens,
which include fluorides, chlorides, bromides, and iodides.
These elements are found in aerosols, detergents, bleaches,
cleaning solvents, salts, air fresheners, adhesives, paint, and
other household products. Locate combustion-air inlet as far as
possible from swimming pool and swimming pool pump
house.
!
CAUTION
UNIT MAY NOT OPERATE
NOTE: All pipe joints must have cemented attachment of
combustion-air inlet pipe to inlet housing connection, since it
may be necessary to remove pipe for servicing.
Assembly of Combustion Air Pipe (Non-Direct Vent/1-Pipe
System ONLY)
1. Permanently
install
perforated
disk
assembly
(factory-supplied in loose parts bag) in combustion-air
elbow using RTV or by cementing, as shown in Fig. 39.
For 120,000 Btuh size units only: separate the 2 halves of
perforated disk assembly and use only the shouldered
disk half.
2. Determine the length of straight portion of combustion-air
inlet pipe from Fig. 39.
3. Cut field-supplied 2-in. (51 mm) diameter PVC pipe to
length as determined per Fig. 39.
Failure to follow this caution may result in incomplete
combustion, flame disturbance, or flame sense lockout.
When installing combustion air and vent system of short pipe
length, the smallest allowable pipe diameter must be used.
NOTE: A 2-in. (51 mm) diameter pipe must be used within
furnace casing. Make all pipe diameter transitions outside furnace
casing per Fig. 41.
2. If required per Table 13, insert perforated disk assembly
(factory-supplied in loose parts bag) in intake housing
where combustion air pipe will be connected. If half disk
set is required, install only shouldered disk half.
33
V
352AAV
V
12 inches (30 cm) for applieances >10,000 Btuh(3 kW)
and < 100,000 Btuh(30kW), 36 inches (91cm) for
appliances > 100,000 Btuh(30kW)
A08600
Table 8 – Direct Vent Termination Clearance
34
352AAV
A08601
Table 9 – Other than Direct Vent Termination Clearance
35
Table 10 – Maximum Allowable Exposed Vent Pipe Length With and Without Insulation in
Winter Design Temperature Ambient*
UNIT SIZE
060
352AAV
080
100
120
WINTER DESIGN
TEMPERATURE °F (°C)
MAX PIPE
DIAMETER
IN. (mm)
WITHOUT
INSULATION
FT (M)
WITH 3/8–IN. (10 mm) OR
THICKER INSULATION
FT (M)†
20 (---7)
0 (---18)
---20 (---29)
20 (---7)
0 (---18)
---20 (---29)
20 (---7)
0 (---18)
---20 (---29)
20 (---7)
0 (---18)
---20 (---29)
20 (---7)
0 (---18)
---20 (---29)
20 (---7)
0 (---18)
---20 (---29)
20 (---7)
0 (---18)
---20 (---29)
2 (51)
2 (51)
2 (51)
2 (51)
2 (51)
2 (51)
2.5 (64)
2.5 (64)
2.5 (64)
2.5 (64)
2.5 (64)
2.5 (64)
3 (76)
3 (76)
3 (76)
3 (76)
3 (76)
3 (76)
4 (102)
4 (102)
4 (102)
44 (13)
21 (6)
20 (6)
55 (17)
30 (9)
16 (5)
58 (18)
29 (9)
14 (4)
40 (12)
38 (12)
21 (6)
63 (19)
30 (9)
12 (4)
70 (21)
38 (12)
19 (6)
65 (20)
26 (8)
5 (2)
70 (21)
70 (21)
57 (17)
55 (17)
55 (17)
55 (17)
70 (21)
70 (21)
67 (20)
40 (12)
40 (12)
40 (12)
70 (21)
70 (21)
70 (21)
70 (21)
70 (21)
70 (21)
70 (21)
70 (21)
65 (20)
* Pipe length (ft) specified for maximum pipe lengths located in unconditioned spaces. Pipes located in unconditioned space cannot exceed total allowable pipe
length as specified in Table 11.
† Insulation thickness based on R value of 3.5 per in.
Attachment of Combustion Air Pipe
1. Determine location of combustion air intake pipe
connection to combustion air intake housing as shown in
Fig. 38 for application.
2. Reposition combustion air intake housing plug fitting in
appropriate unused intake housing connection.
3. Install combustion-air pipe grommet (factory-supplied in
loose parts bag) into selected furnace casing
combustion-air pipe hole. (See Fig. 40.)
4. Insert assembled combustion air inlet pipe into intake
housing as shown in Fig. 38.
5. Drill a 1/8-in. (3 mm) hole in 2-in. (51 mm), combustion
air pipe using the hole in intake housing as a guide.
6. Install a field-supplied No. 6 or No. 8 sheet metal screw
into combustion air pipe.
7. Install casing hole filler cap (factory-supplied in loose
parts bag) in unused combustion air pipe casing hole.
NOTE: Do not attach combustion air intake pipe permanently
to combustion air intake housing since it may be necessary to
remove pipe for service of burner box components or
flame sensor.
Attachment of Combustion Air Intake Housing Plug Fitting
The combustion-air intake plug fitting must be installed in unused
combustion air intake housing. This fitting must be attached by
using RTV sealant, or by drilling a 1/8-in. (3 mm) hole in fitting,
using hole in intake housing as a guide. Install a field-supplied
No. 6 or No. 8 sheet metal screw.
NOTE: DO NOT OVERTIGHTEN SCREW. Breakage of intake
housing or fitting may cause air leakage to occur.
A plugged drain connection has been provided on this fitting for
use when moisture is found in combustion air intake pipe and
combustion box. If use of this drain connection is desired, drill
out fitting’s tap plug with 3/16-in. drill and connect a
field-supplied 3/8-in. tube. This tube should be routed to open
condensate drain for furnace and A/C (if used), and should be
trapped, as shown in Fig. 42.
NOTE:
(Direct Vent/2-Pipe System ONLY). Moisture in
combustion air intake may be a result of improper termination.
Ensure combustion air pipe termination is similar to those as
shown in Fig. 44 so that it will not be susceptible to area where
light snow or other sources of moisture could be pulled in.
VENT PIPE
General
Furnace vent connection must be attached as shown in Fig. 38.
!
WARNING
CARBON MONOXIDE POISONING AND PROPERTY
DAMAGE HAZARD
Failure to follow this warning could result in property damage,
personal injury, or death.
Vent pipes must be airtight.
NOTE: A 2-in. (51 mm) diameter pipe must be used within the
furnace casing. Make all pipe diameter transitions outside furnace
casing per Fig. 41.
The minimum vent pipe length for these furnaces is 5 ft. (2 M).
Short pipe lengths (5-8 ft or 2--3 M) may discharge condensate
droplets. These condensate droplets may be undesirable. A 12-in.
(305 mm) minimum offset pipe section is recommended to reduce
excessive condensate droplets from exiting vent pipe outlet. (See
Fig. 43.)
Attachment of Vent Pipe
1. Determine vent pipe diameter and maximum pipe lengths
using Table 13.
36
Table 11 – Furnace Setup Switch Description
SETUP SWITCH NO.
SWITCH NAME
NORMAL POSITION
SW---1
Adaptive Heat
Mode
OFF
Blower OFF
delay
Blower OFF
delay
SW---2
SW---3
ON or OFF
ON or OFF
DESCRIPTION OF USE
When off, allows 2-stage operation with a single-stage
thermostat. Turn on when using 2-stage thermostat to allow Low
Heat operation when R to W/W1 closes and High Heat operation
when R to W/W1 and W2 close.
Control blower OFF delay time. Used in conjunction with SW-3.
See Table 9B.
Control blower OFF delay time. Used in conjunction with SW-2.
See Table 9B.
NOTE: Select 1 vent pipe connection and NOTE: Select 1 vent pipe connection and
1 combustion-air pipe connection.
1 combustion-air pipe connection.
COMBUSTIONAIR
AIR
FLOW
COMBUSTIONAIR
FIELD-SUPPLIED
2-IN. (51 mm) DIA.
PVC 90° ELBOW
FIELD-SUPPLIED
2-IN. (51 mm) DIA.
PVC PIPE
VENT
VENT
VENT
*
†
UPFLOW
COMBUSTIONAIR
COMBUSTIONAIR
AIR
FLOW
A
†
COMBUSTIONAIR
DOWNFLOW
COMBUSTION-AIR DISC
(FACTORY-SUPPLIED IN
LOOSE PARTS BAG)
COMBUSTIONAIR
A96211
Length of Straight Pipe Portion of
Combustion-Air Inlet Pipe Assembly -- In. (mm)
VENT
VENT
352AAV
*
VENT
**
**
AIR
FLOW
CASING WIDTH
17---1/2 (445)
21(533)
24---1/2 (622)
AIR
FLOW
A
8---1/2 ±1/2 (216 ± 13)
10---1/2 ±1/2 (267 ± 13)
12 ±1/2 (318 ± 13)
Fig. 39 -- Combustion--Air Inlet Pipe Assembly
††
†
HORIZONTAL-LEFT DISCHARGE
†
††
NOTE: (Direct Vent/2-pipe ONLY) vent pipe system has the
same diameter and same length as combustion air pipe mentioned
in section “Assembly of Combustion Air Pipe (Direct Vent/2-Pipe
system ONLY).”
NOTE: Do not count elbows or pipe sections in terminations or
within furnace (all elbows shown in Fig. 44 and Fig. 45 are not be
to counted).
2. Determine location of vent pipe connection to inducer
housing as shown in Fig. 38 for application.
3. Install vent pipe grommet (factory-supplied in loose parts
bag) into selected furnace casing vent pipe hole. (See
Fig. 44.)
4. Reposition elastomeric (rubber) inducer housing outlet cap
and clamp to appropriate unused inducer housing
connection. Tighten clamp.
HORIZONTAL-RIGHT DISCHARGE
* For Non-Direct Vent (1-Pipe) system, orient elbow so that its
opening faces down.
** For Non-Direct Vent (1-Pipe) system, orient elbow so that its
opening faces sideways.
† An external trap kit (see furnace product data sheet) must be used.
††
Bottom combustion-air not allowed for non-direct vent
A05092
Fig. 38 -- Combustion-Air and Vent Pipe Connections
Table 12 – Blower Off Delay Setup Switch (SW) 2-Stage Units
with PSC Blower Motors
DESIRED HEATING MODE
BLOWER-OFF DELAY (SEC)
90
120
150
180
SETUP SWITCH
SW---2
SW---3
OFF
OFF
OFF
ON
ON
OFF
ON
ON
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in unit component
damage.
Inducer housing outlet cap must be installed and fully seated
against inducer housing. Clamp must be tightened to prevent
any condensate leakage.
37
Table 13 – Maximum Allowable Pipe Length -- Ft. (M)
ALTITUDE
FT (M)
UNIT MAX
INPUT
RATE
(BTUH)
60,000
2 Pipe or 2-in.
(51 mm)
Concentric
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
0 to 2000
(0 to 610)
352AAV
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
1
2
3
4
15
(4.6)
70
(21.3)
10
(3.0)
70
(21.3)
5
(1.5)
70
(21.3)
70
(21.3)
70
(21.3)
NA
NA
50
(15.2)
70
(21.3)
35
(10.6)
70
(21.3)
NA
NA
NA
30
(9.1)
70
(21.3)
30
(9.1)
70
(21.3)
20
(6.1)
70
(21.3)
NA
30
(9.1)
70
(21.3)
NA
NA
NA
NA
20
(6.1)
70
(21.3)
20
(6.1)
70
(21.3)
10
(3.0)
70
(21.3)
70
(21.3)
3 (76)
2---1/2 (64) one
disk
2---1/2 (64)
10 (3.0)
NA
NA
NA
NA
NA
40
(12.1)
70
(21.3)
12
(3.6)
67
(20.4)
44
(13.4)
70
(21.3)
26
(7.9)
70
(21.3)
9
(2.7)
62
(18.8)
70
(21.3)
70
(21.3)
11
(3.3)
63
(19.2)
41
(12.4)
70
(21.3)
24
(7.3)
70
(21.3)
58
(17.6)
59
(17.6)
35
(10.6)
70
(21.3)
7
(2.1)
66
(20.1)
30
(9.1)
70
(21.3)
16
(4.8)
70
(21.3)
30
(9.1)
70
(21.3)
25
(7.6)
70
(21.3)
20
(6.1)
70
(21.3)
NA
NA
NA
61
(18.5)
25
(7.6)
70
(21.3)
16
(4.8)
70
(21.3)
61
(18.5)
25
(7.6)
70
(21.3)
6
(1.8)
66
(20.1)
61
(18.5)
15
(4.6)
70
(21.3)
NA
NA
NA
NA
62
(18.8)
63
(19.2)
70
(21.3)
6
(18.8)
62
(18.8)
28
(8.5)
70
(21.3)
15
(4.6)
70
(21.3)
51
(15.5)
58
(17.6)
61
(18.5)
56
(17.)
70
(21.3)
61
(18.5)
50
(15.2)
70
(21.3)
61
(18.5)
43
(13.1)
70
(21.3)
NA
NA
NA
57
(17.3)
23
(7.0)
70
(21.3)
14
(4.2)
66
(20.1)
44
(13.4)
57
(17.3)
57
(17.3)
22
(6.7)
70
(21.3)
5
(1.5)
61
(18.5)
38
(11.5)
57
(17.3)
56
(17.0)
13
(3.9)
70
(21.3)
70
(21.3)
70
(21.3)
70
(21.3)
70
(21.3)
70
(21.3)
2 (51)
1---1/2 (38)
1---1/2 (38)
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
2 (51)
2 (51)
60,000
2 Pipe or 2-in.
(51 mm)
Concentric
1---1/2 (38)
1---1/2 (38)
2 (51)
2 (51)
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
2---1/2 (64)
2---1/2 (64)
3 (76)
3 (76)
3 (76)† no
disk
NA
NA
3 (76)†
4† no disk
4† no disk
70
(21.3)
3 (76)†
NA
3 (76)† no
disk
3 (76)†
1---1/2 (38)
2 (51)
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
2---1/2 (64)
2---1/2 (64)
3 (76)
3 (76)
3 (76)
NA
4† no disk
NA
3 (76)
2 (51)
2 (51)
120,000
NA
2---1/2 (64)
1---1/2 (38)
1---1/2 (38)
2 Pipe or 3-in.
(76 mm)
Concentric
6
2---1/2 (64)
1---1/2 (38)
2 Pipe or 2-in.
(51 mm)
Concentric
2 Pipe or 3-in.
(76 mm)
Concentric
5
20
(6.1)
70
(21.3)
10
(3.0)
55
(16.7)
70
(21.3)
5
(1.5)
40
(12.1)
70
(21.3)
60,000
120,000
3001 to
4000
(914 to
1219)
2 Pipe or 3-in.
(76 mm)
Concentric
NUMBER OF 90° ELBOWS
45
(13.7)
70
(21.3)
17
(5.1)
70
(21.3)
49
(14.9)
70
(21.3)
35
(10.6)
70
(21.3)
14
(4.2)
63
(19.2)
70
(21.3)
70
(21.3)
16
(4.8)
68
(20.7)
46
(14.0)
70
(21.3)
33
(10.0)
70
(21.3)
65
(19.8)
59
(17.9)
120,000
2001 to
3000
(610 to 914)
DIRECT VENT (2-PIPE)
ONLY
TERMINATI
PIPE DIA
ON TYPE
IN. (MM)*
NON-DIRE
CT VENT
(1-PIPE)
ONLY
PIPE DIA
IN. (MM)*
NA
3 (76)†
3 (76)† no
disk
NA
4† no disk
4† no disk
See notes at end of table
38
NA
NA
61
(18.5)
NA
56
(17.0)
31
(9.4)
56
(17.0)
Table 13—Maximum Allowable Pipe Length -- Ft. (M) (Continued)
4001 to
5000
(1219 to
1524)‡
5001 to 6000
(1524 to
1829)‡
6001 to 7000
(1829 to
2134)‡
TERMINATION
TYPE
PIPE DIA
(IN.)*
60,000
2 Pipe or 2-in.
(51 mm)
Concentric
1---1/2 (38)
1---1/2 (38)
2 (51)
2 (51)
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
2---1/2 (64)
2---1/2 (64)
120,000
2 Pipe or 3-in.
(76 mm)
Concentric
DIRECT VENT (2-PIPE) ONLY
10
(3.0)
59
(17.9)
39
(11.8)
70
(21.3)
22
(6.7)
70
(21.3)
46
(14.0)
55
(16.7)
70
(21.3)
9
(2.7)
55
(16.7)
36
(10.9)
70
(21.3)
21
(6.4)
67
(20.4)
35
(10.6)
52
(15.8)
70
(21.3)
8
(2.4)
52
(15.8)
33
(10.0)
70
(21.3)
19
(5.7)
63
(19.2)
24
(7.3)
48
(14.6)
5
(1.5)
58
(17.6)
26
(7.9)
70
(21.3)
13
(3.9)
67
(20.4)
40
(12.1)
54
(16.4)
70
(21.3)
70
(21.3)
3 (76)† no disk
NA
NA
3 (76)†
4† no disk
4† no disk
70
(21.3)
3 (76)† no disk
NA
NA
3 (76)†
4† no disk
4† no disk
1---1/2 (38)
2 (51)
2 (51)
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
2---1/2 (64)
2---1/2 (64)
120,000
2 Pipe or 3-in..
(76 mm)
Concentric
3 (76)
3 (76)
3 (76)† no disk
NA
NA
3 (76)†
4† no disk
4† no disk
60,000
2 Pipe or 2-in.
(51 mm)
Concentric
1---1/2 (38)
1---1/2 (38)
2 (51)
2 (51)
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
2---1/2 (64)
2---1/2 (64)
120,000
3
3 (76)
3 (76)
1---1/2 (38)
2 Pipe or 3-in.
(76 mm)
Concentric
2
3 (76)
3 (76)
2 Pipe or 2-in.
(51 mm)
Concentric
2 Pipe or 3-in.
(76 mm)
Concentric
1
15
(4.6)
64
(19.5)
44
(13.4)
70
(21.3)
31
(9.4)
70
(21.3)
53
(16.1)
56
(17.0)
70
(21.3)
14
(4.2)
60
(18.2)
41
(12.4)
70
(21.3)
29
(8.8)
70
(21.3)
42
(12.8)
53
(16.1)
70
(21.3)
13
(3.9)
57
(17.3)
38
(11.5)
70
(21.3)
27
(8.2)
68
(20.7)
31
(9.4)
49
(14.9)
60,000
100,000
NUMBER OF 90° ELBOWS
See Notes at the end of table
39
4
5
6
NA
NA
NA
53
(16.1)
21
(6.4)
70
(21.3)
12
(3.6)
62
(18.8)
33
(10.0)
53
(16.1)
70
(21.3)
52
(15.8)
20
(6.0)
70
(21.3)
52
(15.8)
11
(3.3)
70
(21.3)
NA
NA
57
(17.3)
26
(7.9)
52
(15.8)
70
(21.3)
52
(15.8)
20
(6.0)
52
(15.8)
70
(21.3)
NA
NA
NA
NA
54
(16.4)
23
(7.0)
70
(21.3)
12
(3.6)
62
(18.8)
29
(8.8)
50
(15.2)
70
(21.3)
49
(14.9)
18
(5.9)
70
(21.3)
11
(3.3)
57
(17.3)
22
(6.7)
49
(14.9)
70
(21.3)
48
(14.6)
17
(5.1)
70
(21.3)
47
(14.3)
8
(2.4)
70
(21.3)
NA
NA
52
(15.8)
15
(4.6)
48
(14.6)
70
(21.3)
47
(14.3)
9
(2.7)
47
(14.3)
70
(21.3)
NA
NA
NA
NA
50
(15.2)
21
(6.4)
68
(20.7)
10
(3.0)
58
(17.6)
18
(5.4)
47
(14.3)
45
(13.7)
16
(4.8)
67
(20.4)
9
(2.7)
53
(16.1)
11
(3.3)
45
(13.7)
44
(13.4)
15
(4.6)
66
(20.1)
43
(13.1)
6
(1.8)
64
(19.5)
NA
NA
48
(14.6)
43
(13.1)
NA
NA
44
(13.4)
43
(13.1)
70
(21.3)
70
(21.3)
67
(20.4)
62
(18.8)
352AAV
ALTITUDE
FT (M)
NON-DIRE
CT VENT
(1-PIPE)
ONLY
PIPE DIA
(IN.)*
UNIT MAX
INPUT
RATE
(BTUH)
Table 13—Maximum Allowable Pipe Length -- Ft. (M) (Continued)
ALTITUDE
FT (M)
352AAV
7001 to
8000
(2134 to
2438)‡
8001 to
9000
(2438 to
2743)‡
9001 to
10,000
(2743 to
3048)‡
UNIT SIZE
(BTUH)
DIRECT VENT (2-PIPE)
ONLY
TERMINATIO
N TYPE
PIPE DIA
(IN.)*
NON-DIRE
CT VENT
(1-PIPE)
ONLY
PIPE DIA
(IN.)*
NUMBER OF 90° ELBOWS
1
2
7
(2.1)
48
(14.6)
31
(9.4)
65
(19.8)
17
(5.1)
58
(17.6)
13
(3.9)
44
(13.4)
56
(17.0)
6
(1.8)
44
(13.4)
28
(8.5)
60
(18.2)
15
(4.6)
54
(16.4)
3
4
5
6
NA
NA
NA
NA
46
(14.0)
19
(5.7)
63
(19.2)
8
(2.4)
53
(16.1)
7
(2.1)
43
(13.1)
51
(15.5)
41
(12.4)
14
(4.2)
62
(18.8)
7
(2.1)
48
(14.6)
40
(12.1)
12
(3.6)
60
(18.2)
38
(11.5)
NA
NA
43
(13.1)
38
(11.5)
NA
NA
NA
41
(12.4)
46
(14.0)
40
(12.1)
41
(12.4)
38
(11.5)
36
(10.9)
NA
NA
NA
NA
42
(12.8)
17
(5.1)
58
(17.6)
7
(2.1)
49
(14.9)
37
(11.2)
12
(3.6)
56
(17.0)
5
(1.5)
44
(13.4)
35
(10.6)
10
(3.0)
55
(16.7)
34
(10.3)
NA
NA
39
(11.8)
34
(10.3)
NA
NA
NA
NA
NA
41
(12.4)
30
(9.1)
39
(11.8)
25
(7.6)
37
(11.2)
20
(6.1)
35
(10.6)
15
(4.6)
34
(10.3)
10
(3.0)
29
(8.8)
NA
3 (76)†
4† no disk
4† no disk
12
(3.6)
53
(16.1)
36
(10.9)
66
(20.1)
25
(7.6)
63
(19.2)
20
(6.0)
46
(14.0)
61
(18.5)
11
(3.3)
49
(14.9)
33
(10.0)
62
(18.8)
23
(7.0)
59
(17.9)
10
(3.0)
43
(13.1)
35
(10.6)
2 (51)
2 (51)
45
(13.7)
40
(12.1)
38
(11.5)
33
(10.0)
31
(9.4)
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
25
(7.6)
55
(16.7)
13
(3.9)
49
(14.9)
37
(11.2)
14
(4.2)
53
(16.1)
5
(1.5)
44
(13.4)
35
(10.6)
9
(2.7)
51
(15.5)
7
(2.1)
49
(14.9)
47
(14.3)
NA
NA
NA
39
(11.8)
33
(10.0)
34
(10.3)
31
(9.4)
29
(8.8)
29
(8.8)
5
(1.5)
NA
NA
NA
NA
60,000
2 Pipe or 2-in.
(51 mm)
Concentric
1---1/2 (38)
1---1/2 (38)
2 (51)
2 (51)
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
2---1/2 (64)
2---1/2 (64)
3 (76)
3 (76)
3 (76)† no disk
NA
120,000
2 Pipe or 3-in.
(76 mm)
Concentric
NA
3 (76)†
4† no disk
4† no disk
1---1/2 (38)
60,000
2 Pipe or 2-in.
(51 mm)
Concentric
1---1/2 (38)
2 (51)
2 (51)
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
2 (51)
2 (51)
2---1/2 (64)
2---1/2 (64)
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
2---1/2 (64)
2---1/2 (64)
3 (76)
3 (76)
3 (76)† no disk
NA
120,000
2 Pipe or 3-in.
(76 mm)
Concentric
60,000
2 Pipe or 2-in.
(51 mm)
Concentric
80,000
2 Pipe or 2-in.
(51 mm)
Concentric
100,000
2 Pipe or 3-in.
(76 mm)
Concentric
2---1/2 (64)
2---1/2 (64)
3 (76)
3 (76)
120,000
2 Pipe or 3-in.
(76 mm)
Concentric
NA
3 (76)†
30
(9.1)
57
(17.3)
21
(6.4)
54
(16.4)
39
(11.8)
4† no disk
4† no disk
10
(3.0)
NA
59
(17.9)
NA
53
(16.1)
NA
*Disk usage --- Unless otherwise specified, use perforated disk assembly (factory-supplied in loose parts bag). If one disk is stated, separate 2 halves of
perforated disk assembly and use shouldered disk half. When using shouldered disk half, install screen side toward inlet box.
†Wide radius elbow.
‡Vent sizing for Canadian installations over 4500 ft (1370 M) above sea level are subject to acceptance by the local authorities having jurisdiction. NA---Not
Allowed; pressure switch will not make.
NOTES:
1. Do not use pipe size greater than those specified in table or incomplete combustion, flame disturbance, or flame sense lockout may occur.
2. Size both the combustion---air and vent pipe independently, then use the larger diameter for both pipes.
3. Assume two 45° elbows equal one 90° elbow. Wide radius elbows are desirable and may be required in some cases.
4. Elbows and pipe sections within the furnace casing and at the vent termination should not be included in vent length or elbow count.
5. The minimum pipe length is 5 ft (2 M) for all applications.
6. Use 3-in. (76 mm) diameter vent termination kit for installations requiring 4-in. (102 mm) diameter pipe.
40
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in unit component
damage.
Inducer housing outlet cap must be installed and fully seated
against inducer housing. Clamp must be tightened to prevent
any condensate leakage.
6. Install casing hole filler cap (factory-supplied in loose
parts bag) in unused vent pipe casing hole.
Attachment of Vent Extension Pipe
Furnaces with 100,000 Btuh and larger input are supplied with a
PVC vent extension pipe (2-in. (51 mm) diameter by 12-in. (305
mm) long). This pipe has a built-in channel to assist vent
condensate disposal. When this vent extension pipe is supplied, it
MUST be used to connect the field vent pipe to furnace inducer
housing on ALL upflow and downflow applications.
NOTE: See label on vent extension pipe for proper installation.
This pipe may be shortened if an elbow is used to connect vent
extension tube to field-installed vent pipe.
Installation Guidelines for Combustion Air Pipe and Vent
Pipe
It is recommended that all pipes be cut, prepared, and
pre-assembled before permanently cementing any joint.
1. Attach combustion air pipe and vent pipe per instructions
in sections “Combustion Air Pipe” and “Vent Pipe.”
2. Working from furnace to outside, cut pipe to required
length(s).
3. Deburr inside and outside of pipe.
COMBUSTION-AIR PIPE GROMMET
UNUSED 1-3/4 -IN. (44 mm)
DIAMETER GAS
CONN. HOLE
COMBUSTION
-AIR PIPE
GAS LINE
GAS LINE ENTRY
HOLE FILLER PLUG
VENT PIPE
GAS LINE GROMMET
VENT PIPE GROMMET
NOTE: PIPE GROMMETS AND ENTRY HOLE FILLER
PLUGS ARE INCLUDED IN FACTORY-SUPPLIED
LOOSE PARTS BAG
A05057
Fig. 40 -- Typical Gas Pipe Arrangement
41
A05057
352AAV
4. Chamfer outside edge of pipe for better distribution of
primer and cement.
5. Clean and dry all surfaces to be joined.
6. Check dry fit of pipe and mark insertion depth on pipe.
7. After pipes have been cut and preassembled, apply
generous layer of cement primer to pipe fitting socket and
end of pipe to insertion mark. Quickly apply approved
cement to end of pipe and fitting socket (over primer).
Apply cement in a light, uniform coat on inside of socket
to prevent buildup of excess cement. Apply second coat.
8. While cement is still wet, twist pipe into socket with 1/4
turn. Be sure pipe is fully inserted into fitting socket.
9. Wipe excess cement from joint. A continuous bead of
cement will be visible around perimeter of a properly
made joint.
10. Handle pipe joints carefully until cement sets.
11. Horizontal portions of the venting system shall be
supportive to prevent sagging support. Support
combustion air piping (if applicable) and vent piping a
minimum of every 5 ft (2 M) (3 ft or .9 M for SDR--21 or
--26 PVC) using perforated metal hanging strap.
12. Slope combustion air piping (if applicable) and vent piping
downward towards furnace a minimum of 1/4 in. (6 mm)
per linear ft with no sags between hangers.
13. Horizontal portions of the venting system shall be installed
so as to prevent the accumulation of condensate.
14. Use appropriate methods to seal openings where
combustion air pipe (if applicable) and vent pipe pass
through roof or sidewall.
5. Be certain that mating surfaces of inducer housing
connection elastomeric (rubber) coupling, and 2-in. (51
mm) diameter vent pipe are clean and dry. Assemble the
elastomeric (rubber) vent coupling (with 2 loose clamps)
onto inducer housing connection. Insert the 2-in. (51 mm)
diameter vent pipe through the elastomeric (rubber)
coupling and fully into inducer housing connection until it
touches a stop inside the inducer housing outlet. Tighten
the screws on both clamps to 15-in-lb. of torque. pipe to
inducer housing. Tighten the clamp screws to 15 in.-lb. of
torque.
NOTE: Starting at furnace, slope vent pipe a minimum of 1/4-in.
(6 mm) per linear ft with no sags between hangers.
EXAMPLE:
An 080--12 size furnace located in Indianapolis, elevation
650 ft (198 M) above sea level, could be installed as either a
direct vent/2-pipe system that requires 3 elbows and 32 ft (10
M) of vent pipe, along with 5 elbows and 34 ft (10 M) of
combustion-air pipe OR a non-direct vent/1-pipe system that
requires 3 elbows and 32 ft (10 M) vent pipe.
FURNACE
For a direct vent/2-pipe system, Table 13 indicates this
application would allow a 2--in. (51 mm) diameter vent pipe,
but require a 2-1/2 in. (64 mm) diameter combustion air pipe.
According to Table 13, 2-in. (51 mm) diameter pipe is good
for 35 ft (11 M) with 3 elbows, but only 30 ft (9 M) with 5
elbows. Therefore, 2-1/2 in. (64 mm) diameter pipe must be
used for both vent and combustion-air pipes since larger
required diameter must always be used for both pipes.
NOT IN
HORIZONTAL
SECTION
PIPE DIAMETER
TRANSITION IN
VERTICAL SECTION
352AAV
A93034
For a non-direct vent/1-pipe system, Table 13 indicates that
this application would allow a 2-in. (51 mm) diameter vent
pipe.
If same installations were in Albuquerque, elevation 5250 ft
(1600 M) above sea level:
Fig. 41 -- Combustion--Air and Vent Pipe Diameter
Transition Location and Elbow Configuration
3/8 ID TUBE
3/16
DRILL
TRAP
COMBUSTION – AIR
INTAKE HOUSING
For a direct vent/2-pipe system, Table 13 indicates that 2-1/2
in. (64 mm) diameter vent pipe and combustion-air pipe are
required.
For a non-direct vent/1-pipe system, Table 13 indicates that
2-1/2-in. (64 mm) diameter vent pipe is required.
BURNER
BOX
COMBUSTION-AIR
PIPE (DIRECT
VENT/2 PIPE)
If same applications are to be installed at 5001 to 6000 ft
(1524 to 1829 M)elevation:
COMBUSTION-AIR
PIPE (NON-DIRECT
VENT/1-PIPE)
For a direct vent/2-pipe system, 2-in. (51 mm) pipe is only
good for 23 ft (7 M) (with 3 elbows) and 17 ft (5 M)(with 5
elbows). Therefore, 2-1/2 in. (64 mm) diameter combustion air
and vent pipe must be used.
For a non-direct vent/1-pipe system, a 2-in. (51 mm)
diameter pipe is only good for 23 ft (7 M) with 3 elbows. A
2-1/2-in. (64 mm) diameter vent pipe must be used.
4″MIN
(102 mm)
TO OPEN
DRAIN
A05093
Fig. 42 -- Air Intake Housing Plug Fitting Drain
42
12″ MIN
(305mm)
12″ MIN
(305mm)
VENT PIPE
VENT PIPE
COMBUSTION-AIR PIPE
HORIZONTAL TO SIDEWALL
352AAV
HORIZONTAL TO ROOF
COMBUSTION-AIR PIPE
COMBUSTION-AIR PIPE
VENT PIPE
COMBUSTION-AIR PIPE
12″ MIN
(304.8mm)
12″ MIN
(304.8mm)
VENT PIPE
VERTICAL TO ROOF
VERTICAL TO SIDEWALL
NOTE: A 12-in. (304.8mm) minimum offset pipe section is recommended
with short (5 to 8 ft / 1.5 to 2.5M) vent systems. This recommendation
is to reduce excessive condensate droplets.
A96230
Fig. 43 -- Short Vent (5 to 8 ft (1.5 to 2.4 M)) System
VENT TERMINATION
building corners, nor by recirculation of flue gases,
airborne leaves, or light snow.
4. Termination or termination kit should be positioned where
it will not be damaged by or subjected to foreign objects
such as stones, balls, etc.
5. Termination or termination kit should be positioned where
vent vapors are not objectionable.
Extended Exposed Sidewall Pipes
Sidewall combustion air pipe termination (direct vent/2-pipe
system only) and vent pipe termination may be extended beyond
area shown in Fig. 44 or in Fig. 45 per application in outside
ambient by insulating pipe as indicated in Table 10.
1. Determine combustion air pipe diameter (direct
vent/2-pipe system only) and vent pipe diameter, as stated
above, using total pipe length and number of elbows.
2. Using winter design temperature (used in load
calculations), find appropriate temperature for your
application and furnace model.
3. Determine required insulation thickness for exposed pipe
length(s).
NOTE: Pipe length (ft) specified for maximum pipe lengths
located in unconditioned spaces cannot exceed total allowable
pipe length as specified in Table 13.
Vent Termination Kit (Direct Vent/2-Pipe System Only)
NOTE: Always refer to the instructions in termination kit for the
latest version.
General
Combustion-air (direct vent/2-pipe system only) and vent pipe
must terminate outside structure, either through sidewall or roof.
For vent termination clearance, refer to Table 8 for Direct
Vent/2-Pipe system and Table 9 for Non-direct Vent/1-Pipe
system. For exterior piping arrangements, refer to
Fig. 44 for Direct Vent/2-Pipe system and Fig. 45 for
Non-Direct/1-Pipe system.
Roof termination is preferred since it is less susceptible to
damage or contamination, and it has less visible vent vapors.
Sidewall termination require sealing or shielding of building
surfaces with a corrosive resistance material due to corrosive
combustion products of vent system.
NOTE: (Direct Vent/2-Pipe system ONLY). A factory accessory
termination kit MUST be used. See section “Vent Termination Kit
(Direct Vent/2-Pipe System Only)” in this instruction.
When determining appropriate location for termination, consider
the following guidelines:
1. Comply with all clearance requirements stated in Table 8
or Table 9 per application.
2. Termination or termination kit should be positioned where
vent vapors will not damage plants/shrubs or air
conditioning equipment.
3. Termination or termination kit should be positioned so that
it will not be affected by wind eddy, such as inside
43
Table 14 – Vent Termination Kit for Direct Vent/2-Pipe System
DIRECT VENT (2-PIPE) TERMINATION KIT
TERMINATION SYSTEM
DIAM. OF COMBUSTION AIR AND VENT
PIPES --- IN (mm)
2-in. (51 mm) Concentric Vent Kit
3-in. (76 mm)Concentric Vent Kit
2-in. (51 mm)Termination Bracket Kit
3-in. (76 mm) Termination Bracket Kit
Single Penetration of Wall or Roof
Single Penetration of Wall or Roof
2---Pipe Termination System
2---Pipe Termination System
1, 1---1/2, 2, or 2---1/2 (25, 38, 51, 64 mm)
2---1/2, 3 or 4 (64, 76, 102 mm)
1, 1---1/2 or 2 (25, 38, 51mm)
2---1/2, 3 or 4 (64, 76, 102 mm)
Roof Te rmination (Preferred)
At least 36 in.
(914mm)
Concentric Vent and Combustion Air
Roof Termination (preferred)
A
352AAV
Vertical separation
between combustion
air and vent
8 3/4 in. (222mm)for 3 in. (76mm)ki t
6 3/4 in. (172mm)for 2 in. (51mm) ki t 18 in. maximum (457mm)
A
At least
36 in.
(914mm)
Maintain 12 in. (305mm)min
.
clearance above
highest anticipated
snow level
Maximum of 24 in.(614mm)
above roof
Maintain 12 in. (305mm)
min. clearance above
highest anticipated
snow level, maximum of
24 in. above roof
1 in. (25mm) maximum (typ) from wall to inlet
Abandoned masonry
used as raceway
(per code)
12 in. (305mm) minimum from
overhang or roof
Note: "A" denotes 0 to < 2 in. (51mm)
Between the first 2 vents
Third vent must be > 36 in. away
(914mm)
At
le
36 ast
in
.
12 in. min from
overhang or roof
(typ)
A
Maintain 12 in. (305mm)
min. clearance above
highest anticipated
snow level or grade
whichever is greater
Concentric Vent
and Combustion - Air
Side Te rmination
A
At least 36 in.
(914mm)
12 in. (305mm)
separation between
bottom ofcombustion air and
bottom of vent (typ)
90°
A
Side wall termination
of less than 12 in. (305mm) above highest snow level
Maintain 12 in. (305mm)
min. clearance above
highest anticipated
snow level or grade
whichever is greater (typ)
6 in.
ast 3
At le mm)
(914
A05090
Fig. 44 -- Combustion Air and Vent Pipe Termination for Direct Vent (2-pipe) System
Roof Termination (Preferred)
Vent
Maintain 12 in (305mm)
.
minimum clearance
above highest anticipated
snow level maximum of
24 in. (610mm) above. roof
Abandoned masonry
used as raceway
(per code)
12 in. min. (305 mm)from
overhang or roof
6 in. (152mm) minimum clearance
between wall and end of vent pipe.
10 in. (254mm) maximum pipe length
Maintain 12 in. (305mm)
minimum clearance
above highest anticipated
snow level or grade
whichever is greater
12 in. (305 mm) min. from
overhang or roof
Sidewall Termination
with Straight Pipe (preferred)
90°
Maintain 12 in. (305mm)
minimum clearance
above highest anticipated
snow level or grade
whichever is greater.
Side wall termination
with 2 elbows (preferred)
A05091
Fig. 45 -- Vent Pipe Termination for Non-Direct Vent (1-pipe) System
44
(Direct Vent/2-Pipe System ONLY) -- When 2 or more 352AAV
furnaces are vented near each other, 2 vent terminations may be
installed as shown in Fig. 44, but next vent termination must be at
least 36 in. (914 mm) away from first 2 terminations. It is
important that vent terminations be made as shown in Fig. 44 to
avoid recirculation of flue gases.
Combustion air and vent pipes MUST terminate outside structure.
A factory accessory termination kit must be installed as shown in
Table 14. There are four options of vent/combustion air
termination kits available as shown in Table 14.
NOTE: Combustion air pipe must have the same diameter as
vent pipe.
Concentric Vent/Combustion Air Termination Kit (Direct
Vent/2-Pipe System Only)
Determine an appropriate location for termination kit using the
guidelines provided in section “Vent Termination: General” in
this instruction.
1. Cut one 4-in. (102 mm) diameter hole for 2-in. (51 mm)
kit, or one 5-in. (127 mm) diameter hole for 3-in. (76 mm)
kit.
2. Loosely assemble concentric vent/combustion air
termination components together using instructions in kit.
3. Slide assembled kit with rainshield REMOVED
through hole.
NOTE: Do not allow insulation or other materials to accumulate
inside of pipe assembly when installing it through hole.
Roof terminations -- Locate assembly through roof to
appropriate height as shown in Fig. 44.
Sidewall terminations -- Locate assembly through
sidewall with rain shield positioned no more than 1-in. (25
mm) from wall as shown in Fig. 44.
4. Disassemble loose pipe fittings. Clean and cement using
same procedures as used for system piping.
5. Check required dimensions as shown in Fig. 44.
Two-Pipe Termination Kit (Direct Vent/2-Pipe System Only)
Determine an appropriate location for termination kit using the
guidelines provided in section “Vent Termination: General” in
this instruction.
1. Cut 2 holes, 1 for each pipe, of appropriate size for pipe
size being used.
2. Loosely install elbow in bracket and place assembly on
combustion-air pipe.
Roof terminations -- Loosely install pipe coupling on
properly cut vent pipe. Coupling must be positioned so
bracket will mount as shown in Fig. 44.
For applications using combustion-air pipe option,
indicated by dashed lines in Fig. 44, install 90° street
elbow into 90° elbow, making a U-fitting. A 180° U-fitting
may be used.
Sidewall terminations -- Install bracket as shown in Fig.
44. For applications using vent pipe option indicated by
dashed lines in Fig. 44, rotate vent elbow 90° from
position shown in Fig. 44.
3. Disassemble loose pipe fittings. Clean and cement using
same procedures as used for system piping.
4. Check required dimensions as shown in Fig. 44.
Multi--venting and Vent Terminations
When 2 or more 352AAV Furnaces are vented near each other,
each furnace must be individually vented. NEVER common vent
or breach vent 352AAV furnaces.
Step 11 -- Condensate Drain
!
CAUTION
Failure to follow this caution may result in intermittent
unit operation.
Unit must not be installed, operated, and then turned off and
left in an unoccupied structure during cold weather when
temperature drops to 32°F (0°C) and below unless drain trap
and drain line have adequate freeze protection. See Service
and Maintenance Instructions for winterizing procedure.
GENERAL
Condensate trap is shipped installed in the blower shelf and
factory connected for UPFLOW applications. Condensate trap
must be RELOCATED for use in DOWNFLOW and
HORIZONTAL applications.
Condensate trap MUST be used for all applications.
An external trap is not required when connecting the field drain
to this condensate trap.
The field drain connection (condensate trap or drain tube
coupling) is sized for l/2-in. (13 mm) CPVC, 1/2-in. (13 mm)
PVC, or 5/8-in. (16 mm) ID tube connection.
Drain pipe and fittings must conform to ANSI standards and
ASTM D1785, D2466 or D2846. CPVC or PVC cement must
conform to ASTM D2564 or F493. Primer must conform to
ASTM F656. In Canada, use CSA or ULC listed schedule 40
CPVC or PVC drain pipe, fittings, and cement.
When a condensate pump is required, select a pump which is
approved for condensing furnace applications. To avoid
condensate spillage, select a pump with an overflow switch.
Furnace condensate is mildly acidic, typically in the pH range of
3.2 to 4.5. Due to corrosive nature of this condensate, a
condensate pH neutralizing filter may be desired. Check with
local authorities to determine if a pH neutralizer is required.
APPLICATION
The furnace, A/C, and humidifier drains may be combined and
drained together. The A/C drain must have an external,
field-supplied trap prior to the furnace drain connection. All drain
connections (furnace, A/C, or humidifier) must be terminated into
an open or vented drain as close to the respective equipment as
possible to prevent siphoning of the equipment’s drain.
See Fig. 46 for example of possible field drain attachment using
1/2-in. (13 mm) CPVC or PVC tee for vent and A/C or humidifier
drain connection.
Outdoor draining of the furnace is permissible if allowed by local
codes. Caution should be taken when freezing. Ambient may
freeze drain pipe and prohibit draining.
45
352AAV
UNIT MAY NOT OPERATE
CONDENSATE TRAP
OPEN STAND
PIPE FOR
A/C OR
HUMIDIFIER
DRAIN
WIRE TIE(S)
352AAV
TEE
TO OPEN
DRAIN
HEAT TAPE
(3 WRAPS MINIMUM)
A94054
Fig. 46 -- Example of Field Drain Attachment
!
Fig. 47 -- Condensate Trap Heat Tape
WARNING
Step 1 -- General
The furnace must have a 115-v power supply properly connected
and grounded.
NOTE:
Proper polarity and proper grounding must be
maintained for 115-v wiring. If polarity is incorrect, control status
indicator light will flash rapidly and the furnace will not operate.
Natural gas service pressure must not exceed 0.5 psig (14-in. wc),
and be no less than 0.16 psig (4.5-in. wc).
Thermostat wire connections at R and W/W1 are the minimum
required for gas heating operation. W2 must be connected for
2-stage heating thermostats. COM, Y/Y2, and G are required for
cooling, heat pumps, and some clock thermostats. These must be
made at the 24-v terminal block on the control. (See Fig. 37.)
This furnace can be installed with either a single-stage heating or
a 2-stage heating thermostat.
For single-stage thermostats, connect thermostat W to W/W1 at
furnace control terminal block. (See Fig. 31 and 50H.) For
single-stage thermostats, the control will determine, based on
length of previous heating on and off cycles, when to operate in
low- and high-gas heat for optimum comfort. Setup switch-1
(SW-1) must be in the factory-shipped OFF position. See Fig. 36
and Table 11 and 12 for setup switch information.
PERSONAL INJURY HAZARD
Caution should be taken to prevent draining where slippery
conditions may cause personal injuries.
Excessive condensate draining may cause saturated soil
conditions which could result in damage to plants.
CONDENSATE DRAIN PROTECTION
Freezing condensate left in condensate trap and drain line may
cause cracks, and possible water damage may occur. If freeze
protection is required, use condensate freeze protection accessory
or equivalent 3 to 6 watt per ft at 120-v and 40°F (4°C)
self-regulating, shielded, and waterproof heat tape. See
Installation Instructions supplied with accessory or heat tape
manufacturer’s recommendations.
1. Fold heat tape in half and wrap on itself 3 times.
2. Locate heat tape between sides of condensate trap back.
(See Fig. 47.)
3. Use wire ties to secure heat tape in place. Wire ties can be
positioned in notches of condensate trap sides. (See Fig.
47.)
4. Wrap field drain pipe with remaining heat tape,
approximately 1 wrap per ft.
5. When using field-supplied heat tape, follow heat tape
manufacturer’s instructions for all other installation
guidelines.
START-UP ADJUSTMENT AND
SAFETY CHECK
!
A93036
CAUTION
FURNACE MAY NOT OPERATE
Failure to follow this caution may result in furnace operation
stopping and water pipes freezing during cold weather.
Furnace control must be grounded for proper operation, or
control will lockout. Control is grounded through green/yellow
wire connected to gas valve C-terminal and burner box screw.
46
!
CAUTION
FIRE HAZARD
Failure to follow this caution may result in intermittent unit
operation or performance satisfaction.
This furnace is equipped with a manual reset limit switch in
the burner box area. The switch will open and shut off power
to the gas valve if a flame rollout or overheating condition
occurs in the burner enclosure area. DO NOT bypass the
switch. Correct inadequate combustion-air supply, component
failure, or restricted flue gas passageway before resetting
the switch.
!
CAUTION
UNIT MAY NOT OPERATE
Failure to follow this caution may result in intermittent unit
operation or performance satisfaction.
Condensate trap must be PRIMED or proper draining may not
occur. The condensate trap has internal chambers which can
ONLY be primed by pouring water into the inducer drain side
of condensate trap.
A99118
Fig. 48 -- Inducer Housing Drain Tube Cap
If a 2-stage heating thermostat is to be used, move SW-1 to ON
position at end of furnace installation. This overrides built-in
control process for selecting high and low fire and allows the
2-stage thermostat to select gas heating modes. The W2 from
thermostat must be connected to W2 on control terminal block.
(See Fig. 32 and 50--57.)
Before operating furnace, check each flame rollout manual reset
switch for continuity. If necessary, press and release button to
reset switch. The blower compartment door must be in place to
complete the 115-v circuit to the furnace.
1. Remove upper inducer housing drain connection cap. (See
Fig. 48.)
2. Connect field-supplied 1/2-in. (13 mm) ID tube to upper
inducer housing drain connection.
3. Insert field-supplied funnel into tube.
4. Pour 1 quart of water into funnel/tube. Water should run
through inducer housing, overfill condensate trap, and
flow into open field drain. (See Fig. 49.)
5. Remove funnel and tube from inducer housing and replace
drain connection cap and clamp.
Step 3 -- Purge Gas Lines
After all connections have been made, purge the gas lines and
check for leaks.
!
WARNING
FIRE AND EXPLOSION HAZARD
Failure to follow this warning could result in a fire, explosion,
personal injury, or death.
never purge a gas line into a combustion chamber. Never test
for gas leaks with an open flame. Use a commercially
available soap solution made specifically for the detection of
leaks to check all connections, as specified in “Gas Piping”
and “Start-up Adjustment, and Safety Check” sections of
these instructions.
Step 4 -- Sequence of Operation
Using schematic diagram in Fig. 36, follow the sequence of
operation through the different modes. Read and follow diagram
very carefully.
NOTE: If power interruption occurs during “call for heat”
(W/W1 or W/W1 and W2), the control will run the blower for the
selected blower off delay period after power is restored, if the
thermostat is still calling for gas heating. The amber LED will
flash code 12 during this period, after which the LED will be ON
continuous as long as no faults are detected. After this period, the
furnace will respond to the thermostat normally.
The blower door must be installed for power to be conducted
through blower door interlock switch ILK to furnace control
A99119
Fig. 49 -- Filling Condensate Trap
47
352AAV
Step 2 -- Prime Condensate Trap With Water
CPU, transformer TRAN, inducer motor IDM, blower motor
BLWM, hot surface igniter HSI, and gas valve GV.
352AAV
TWO-STAGE HEATING WITH SINGLE-STAGE
THERMOSTAT (ADAPTIVE MODE)
(See Fig. 31 for thermostat connections.)
NOTE:
Low-heat-only switch, SW-1, selects either the
low-heat-only operation mode when ON, or adaptive heating
mode when OFF, in response to a call for heat. (See Fig. 37.)
This furnace can operate as a 2-stage furnace with a single-stage
thermostat because furnace control CPU includes a programmed
adaptive sequence of controlled operation, which selects low-gasheat or high-gas-heat operation. This selection is based upon the
stored history of the length of previous gas heating on/off periods
of the single-stage thermostat.
The furnace will start up in either low-or high-gas heat. If the
furnace starts up in low-gas heat, the control CPU determines the
low-gas heat on time (from 0 to 16 minutes) which is permitted
before switching to high-heat.
If power is interrupted, the stored history is erased. When this
happens, the control CPU will initially select low-heat for up to
16 minutes and then switch to high-heat, as long as the thermostat
continues to “call for heat.” Subsequent selection is based on
stored history of thermostat cycle times.
When wall thermostat “calls for heat”, R-W/W1 circuit closes.
The furnace control performs a self check, verifies the low-heat
and high-heat pressure switch contacts LPS and HPS are open,
and starts inducer motor IDM in high speed.
1. Inducer Prepurge Period -- If the furnace control CPU
selects low-heat operation the inducer motor IDM comes
up to speed, the low-heat pressure switch LPS closes, and
the furnace control CPU begins a 15-second prepurge
period. After the low-heat pressure switch re-closes the
furnace control CPU will begin a 15-second prepurge
period, and continue to run the inducer motor IDM at
high-speed.
If the furnace control CPU selects high-heat operation, the
inducer motor IDM remains running at high-speed, and the
high-heat pressure switch relay HPSR is de-energized to
close the NC contact. When sufficient pressure is available
the high-heat pressure switch HPS closes, and the
high-heat gas valve solenoid GV-HI is energized. The
furnace control CPU begins a 15-second prepurge period
after the low-heat pressure switch LPS closes. If the
high-heat pressure switch HPS fails to close and the
low-heat pressure switch LPS closes, the furnace will
operate at low-heat gas flow rate until the high-heat
pressure switch closes for a maximum of 2 minutes
after ignition.
2. IgniterWarm-Up -- At end of the inducer prepurge period,
the Hot Surface Igniter HSI is energized for a 17-sec
igniter warm-up period.
3. Trial-For-Ignition Sequence -- When the igniter warm-up
period is completed the main gas valve relay contacts
GVR close to energize the gas valve GV, the gas valve
opens. The gas valve GV permits gas flow to the burners
where it is ignited by the Hot Surface Igniter HSI. Five
seconds after the GVR closes, a 2-second flame period
begins. The HIS igniter will remain energized until the
flame is sensed or until the 2-second flame proving
period begins.
4. Flame-Proving -- When burner flame is proved at the
flame-proving sensor electrode FSE, the inducer motor
IDM switches to low-speed unless running at high-speed,
and the furnace control CPU begins the blower-ON delay
period and continues to hold the gas valve GV-M open. If
the burner flame is not proved within two seconds, the
control CPU will close the gas valve GV-M, and the
5.
6.
7.
8.
control CPU will repeat the ignition sequence for up to
three more Trials-For-Ignition before going to
Ignition-Lockout. Lockout will be reset automatically
after three hours, by momentarily interrupting 115 vac
power to the furnace, or by interrupting 24 vac power at
SEC1 or SEC2 to the furnace control CPU (not at W/W1,
G, R, etc.). If flame is proved when flame should not be
present, the furnace control CPU will lock out of
Gas-Heating mode and operate the inducer motor IDM on
high speed until flame is no longer proved.
Blower-On Delay -- If burner flame is proven the blower
motor BLWM is energized 66 sec after gas valve GV-M is
opened.
Low-heat -- The blower motor BLWM is energized at LO
HEAT speed.
Hi-heat -- The BLWM is energized at HI HEAT speed.
Simultaneously, the electronic air cleaner terminal EAC-1
is energized and remains energized as long as the blower
motor BLWM is energized.
Switching From Low- To High-Heat -- If the furnace
control CPU switches from low-heat to high-heat, the
furnace control CPU will switch the inducer motor IDM
speed from low to high. The high-heat pressure switch
relay HPSR is de-energized to close the NC contact. When
sufficient pressure is available the high-heat pressure
switch HPS closes, and the high-heat gas valve solenoid
GV-HI is energized. The blower motor BLWM will switch
to HI HEAT speed five seconds after the furnace control
CPU switches from low-heat to high-heat.
Switching From High- To Low-Heat -- The control CPU
will not switch from high-heat to low-heat while the
thermostat R-to-W circuit is closed when a single-stage
thermostat is used.
Blower-Off delay -- When the thermostat is satisfied, the
R to W circuit is opened, de-energizing the gas valve
GV-M, stopping gas flow to the burners, and de-energizing
the humidifier terminal HUM. The inducer motor IDM
will remain energized for a 15-second post-purge period.
The blower motor BLWM and air cleaner terminal EAC-1
will remain energized for 90, 120, 150, or 180 seconds
(depending on selection at blower-OFF delay switches).
The furnace control CPU is factory-set for a 120-second
blower-OFF delay.
TWO-STAGE HEATING WITH TWO-STAGE
THERMOSTAT (NON-ADAPTIVE HEATING MODE)
(See Fig. 32 and 50--56 for thermostat connections).
NOTE: In this mode, the low-heat only switch must be ON to
select the low-heat only operation mode in response to closing the
thermostat R-to-W1 circuit. Closing the thermostat R-to-W1
and-W2 circuits always causes high-heat operation, regardless of
the setting of the low-heat-only switch.
The wall thermostat “calls for heat”, closing the R to W1 circuit
for low-heat or closing the R to W1 and-W2 circuits for
high-heat. The furnace control performs a self-check, verifies the
low-heat and high-heat pressure switch contacts LPS and HPS are
open, and starts the inducer motor IDM in high-speed.
The start-up and shutdown functions and delays described in
item 1 above apply to 2-stage heating mode as well, except for
switching from low-to high-heat and vice versa.
1. Switching From Low- To High-Heat -- If the thermostat
R to W1 circuit is closed and the R to W2 circuit closes,
the furnace control CPU will switch the inducer motor
IDM speed from low to high. The high-heat pressure
switch relay HPSR is de-energized to close the NC
contact. When sufficient pressure is available the high-heat
pressure switch HPS closes, and the high-heat gas valve
solenoid GV-HI is energized. The blower motor BLWM
48
G-and-Y1-and-Y/Y2 circuits switch the furnace blower
motor BLWM to COOL speed.
NOTE: When transitioning from low-cooling to high-cooling the
outdoor unit compressor will shutdown for 1 minute while the
BLWM continues to run at low-cool speed (same speed as
LO-HEAT) until the outdoor unit compressor comes back on at
high speed.
The electronic air cleaner terminal EAC-1 is energized
with 115 vac whenever the blower motor BLWM is
operating. When the thermostat is satisfied, the R to
G-and-Y circuit are opened. The outdoor unit stops, and
the furnace blower BLWM and electronic air cleaner
terminal EAC-1 will remain energized for an additional 90
seconds. Jumper Y1 to DHUM to reduce the cooling
off-delay to 5 seconds. (See Fig. 37.)
3. Two-Speed Cooling and Two-Stage Thermostat
(See Fig. 32 and Fig. 50--56 for thermostat connections)
NOTE: The ACRDJ must be disconnected to allow thermostat
control of the outdoor unit staging. (See Fig. 37.)
COOLING MODE
The thermostat “calls for cooling”.
1. Single-Speed Cooling
(See Fig. 31 or 32 and 50, 52, or 54 for thermostat connections.) The thermostat closes R-to-G-and-Y circuits. The Rto-Y circuit starts the outdoor unit, and R-to-G-and-Y/Y2
circuits start the furnace blower motor BLWM on COOL
speed. The electronic air cleaner terminal EAC-1 is energized with 115-v when blower motor BLWM is operating.
When the thermostat is satisfied, the R-to-G-and-Y circuits
are opened. The outdoor unit will stop, and furnace blower
motor BLWM will continue operating on COOL speed for an
additional 90 sec. Jumper Y/Y2 to DHUM to reduce the cooling off-delay to 5 seconds. (See Fig. 37.)
2. Two-Speed Cooling and Single-Stage Thermostat
(Adaptive Mode)
(See Fig. 31 and 50--57 for thermostat connections.)
This furnace can operate a two-speed cooling unit with a
single-stage thermostat because the furnace control CPU
includes a programmed adaptive sequence of controlled
operation, which selects low-cooling or high-cooling
operation. This selection is based upon the stored history of
the length of previous cooling period of the single-stage
thermostat.
NOTE: The air conditioning relay disable jumper ACRDJ must
be connected to enable the adaptive cooling mode in response to
a call for cooling. (See Fig. 32.) When in place the furnace
control CPU can turn on the air conditioning relay ACR to
energize the Y/Y2 terminal and switch the outdoor unit to
high-cooling.
The furnace control CPU can start up the cooling unit in
either low-or high-cooling. If starting up in low-cooling,
the furnace control CPU determines the low-cooling
on-time (from 0 to 20 minutes) which is permitted before
switching to high-cooling.
If the power is interrupted, the stored history is erased and
the furnace control CPU will select low-cooling for up to
20 minutes and then energize the air conditioning relay
ACR to energize the Y/Y2 terminal and switch the outdoor
unit to high-cooling, as long as the thermostat continues to
call for cooling. Subsequent selection is based on stored
history of the thermostat cycle times.
The wall thermostat “calls for cooling”, closing the R to
G-and-Y circuits. The R to Y1 circuit starts the outdoor
unit on low-cooling speed, and the R to G-and-Y1 circuits
starts the furnace blower motor BLWM at low-cool speed
(same speed as LO HEAT).
If the furnace control CPU switches from low-cooling to
high-cooling, the furnace control CPU will energize the air
conditioning relay ACR. When the air conditioning relay
ACR is energized the R to Y1-and-Y2 circuits switch the
outdoor unit to high-cooling speed, and the R to
The thermostat closes the R to G-and-Y1 circuits for lowcooling or closes the R to G-and-Y1-and-Y2 circuits for
high-cooling. The R to Y1 circuit starts the outdoor unit on
low-cooling speed, and the R to G-and-Y1 circuit starts the
furnace blower motor BLWM on low-cool speed (same
speed as LO-HEAT).
The R-to-Y1-and-Y2 circuits start the outdoor unit on
high-cooling speed, and the R to G-and-Y/Y2 circuits start the
furnace blower motor BLWM on COOL speed.
The electronic air cleaner terminal EAC-1 is energized with
115 vac whenever the blower motor BLWM is operating.
When the thermostat is satisfied, the R-to-G-and-Y1 or R-to
G-and-Y1-and-Y2 circuits are opened. The outdoor unit stops,
and the furnace blower BLWM and electronic air cleaner terminal
EAC-1 will remain energized for an additional 90 seconds.
Jumper Y1 to DHUM to reduce the cooling off-delay to 5
seconds. (See Fig. 37.)
THERMIDISTAT MODE
(See Fig. 50--53 for Thermidistat connections.)
The dehumidification output, DHUM on the Thermidistat should
be connected to the furnace control thermostat terminal DHUM.
When there is a dehumidify demand, the DHUM input is
activated, which means 24 vac signal is removed from the
DHUM input terminal. In other words, the DHUM input logic is
reversed. The DHUM input is turned ON when no dehumidify
demand exists. Once 24 vac is detected by the furnace control on
the DHUM input, the furnace control operates in Thermidistat
mode. If the DHUM input is low or OFF for more than 48 hours,
the furnace control reverts back to non-Thermidistat mode.
The cooling operation described above also applies to operation
with a Thermidistat. The exceptions are listed below:
a. When the R to G-and-Y1 circuit is closed and there is
a demand for dehumidification, the furnace blower
motor BLWM will continue running at low-cool speed
(same speed as LO HEAT).
49
352AAV
will switch to HI HEAT speed five seconds after the R to
W2 circuit closes.
2. Switching From High-To Low-Heat -- If the thermostat R
to W2 circuit opens, and the R to W1 circuit remains
closed, the furnace control CPU will switch the inducer
motor IDM speed from high to low. The high-heat
pressure switch relay HPSR is energized to open the NC
contact and de-energize the high-heat gas valve solenoid
GV-HI. When the inducer motor IDM reduces pressure
sufficiently, the high-heat pressure switch HPS will open.
The gas valve solenoid GV-M will remain energized as
long as the low-heat pressure switch LPS remains closed.
The blower motor BLWM will switch to LO HEAT speed
five seconds after the R to W2 circuit opens.
352AAV
A00275
A00277
Fig. 50 -- Two--Stage Furnace with Single--Speed
Air Conditioner
Fig. 52 -- Two--Stage Furnace with Single--Speed
Heat Pump (Dual Fuel)
A00276
A00278
Fig. 51 -- Two--Stage Furnace with Two--Speed
Air Conditioner
Fig. 53 -- Two--Stage Furnace with Two--Speed
Heat Pump (Dual Fuel)
50
352AAV
A00279
A00281
Fig. 54 -- Dual Fuel Thermostat with Two--Stage Furnace and
Single--Speed Heat Pump
Fig. 56 -- Two--Stage Thermostat with Two--Stage Furnace
and Two--Speed Air Conditioner
See note 2
A00280
A00282
Fig. 55 -- Dual Fuel Thermostat with Two--Stage Furnace and
Two--Speed Heat Pump
Fig. 57 -- Single--Stage Thermostat with Two--Stage Furnace
and Two--Speed Air Conditioner
51
NOTES FOR FIG. 50--57:
1. Heat pump MUST have a high pressure switch for dual fuel applications.
2. Refer to outdoor equipment Installation Instructions for additional information and setup procedure.
3. Select the “ZONE” position on the two-speed heat pump control.
4. Outdoor Air Temperature Sensor must be attached in all dual fuel applications.
5. Dip switch No. 1 on Thermidistat should be set in OFF position for air conditioner installations. This is factory default.
6. Dip switch No. 1 on Thermidistat should be set in ON position for heat pump installations.
7. Dip switch No. 2 on Thermidistat should be set in OFF position for single-speed compressor operation.
This is factory default.
8. Dip switch No. 2 on Thermidistat should be set in ON position for two-speed compressor operation.
352AAV
9. Configuration Option No. 10 “Dual Fuel Selection” must be turned ON in all dual fuel applications.
10. NO connection should be made to the furnace HUM terminal when using a Thermidistat.
11. Optional connection. If wire is connected, dip switch No. 1 on furnace control should be set in ON position to allow Thermidistat/
Thermostat to control furnace staging.
12. Optional connection. If wire is connected, ACRDJ jumper on furnace control should be removed to allow Thermidistat/Thermostat
to control outdoor unit staging.
13. Furnace must control its own high-stage heating operation via furnace control algorithm. This is factory default.
14. The RVS Sensing terminal “L” should not be connected. This is internally used to sense defrost operation.
15. DO NOT SELECT the “FURNACE INTERFACE” or “BALANCE POINT” option on the two-speed heat pump control board.
This is controlled internally by the Thermidistat/Dual Fuel Thermostat.
16. Dip switch D on Dual Fuel Thermostat should be set in OFF position for single-speed compressor operation. This is factory
default.
17. Dip switch D on Dual Fuel Thermostat should be set in ON position for two-speed compressor operation.
52
CONTINUOUS BLOWER MODE
When the R to G circuit is closed by the thermostat, the blower
motor BLWM will operate on continuous-blower speed (can be
set to LO HEAT, HI HEAT, or COOL speed). Factory default is
LO HEAT speed. Terminal EAC-1 is energized as long as the
blower motor BLWM is energized.
During a call for heat, the blower BLWM will stop during igniter
warm-up (17 seconds), ignition (7 seconds), and blower-ON
delay (66 seconds), allowing the furnace heat exchangers to heat
up more quickly, then restarts at the end of the blower-ON delay
period at LO HEAT or HI HEAT speed respectively.
In high-heat, the furnace control CPU will hold the blower motor
BLWM at HI HEAT speed during the selected blower-OFF delay
period before reverting to continuous-blower speed.
When the thermostat “calls for low-cooling”, the blower motor
BLWM will switch to operate at low-cool speed (same speed as
LO HEAT). When the thermostat is satisfied, the blower motor
BLWM will operate an additional 90 seconds on low-cool speed
before reverting back to continuous-blower speed.
When the thermostat “calls for high-cooling”, the blower motor
BLWM will operate at COOL speed. When the thermostat is
satisfied, the blower motor BLWM will operate an additional 90
seconds on COOL speed before reverting back to
continuous-blower speed.
When the R to G circuit is opened, the blower motor BLWM will
continue operating for an additional 5 seconds, if no other
function requires blower motor BLWM operation.
Continuous Blower Speed Selection from Thermostat -- To
select different continuous-blower speeds from the room
thermostat, momentarily turn off the FAN switch or push-button
on the room thermostat for 1 -- 3 seconds after the blower motor
BLWM is operating. The furnace control CPU will shift the
continuous- blower speed from the factory setting of LO HEAT to
HI HEAT speed. Momentarily turning off the FAN switch again
at the thermostat will shift the continuous-blower speed from HI
HEAT to COOL. Repeating the procedure will shift the
continuous-blower speed from COOL to LO HEAT speed. The
selection can be changed as many times as desired and is stored
in the memory to be automatically used following a power
interruption.
COMPONENT SELF-TEST
NOTE:
The furnace control component test allows all
components to run for a short time; except the gas valve and
humidifier terminal HUM are not energized for safety reasons.
The EAC-1 terminal is energized when blower is energized. This
feature helps diagnose a system problem in case of a component
failure. The component test feature will not operate if any
thermostat signal is present at control and not until all time delays
are completed.
To Begin Component Self-Test:
!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in electrical shock,
personal injury, or death.
Blower access panel door switch opens 115-v power to control
board. No component operation can occur. Caution must be
taken when manually closing this switch for service purposes.
1.
2.
3.
4.
Remove blower access door.
Disconnect thermostat R lead from furnace control.
Manually close blower door switch.
For approximately 2 sec, short (jumper) the COM-24v
terminal on control to the TEST/TWIN 3/16-in. (5 mm)
quick- connect terminal on control until LED turns off.
Remove jumper from terminals. (See Fig. 37.)
NOTE: If TEST/TWIN and COM-24v terminals are jumpered
longer than 2 sec, LED will flash rapidly and ignore component
test request.
Component test sequence for 2-stage furnace is as follows:
a. LED will display previous status code 4 times.
b. Inducer motor starts on high-speed and continues to
run until Step g of component test sequence.
c. Hot surface igniter is energized for 15 sec, then off.
d. Blower motor operates on LO-HEAT speed for 10 sec.
e. Blower motor operates on HI-HEAT speed for 10 sec.
f. Blower motor operates on COOL speed for 10 sec.
g. Inducer motor goes to low-speed for 10 sec, then stops.
5. Reconnect R lead to furnace control, remove tape from
blower door switch, and re-install blower door.
HEAT PUMP
(See Fig. 50 C--F for thermostat connections)
When installed with a heat pump, the furnace control
automatically changes the timing sequence to avoid long blower
off times during demand defrost cycles. When the R to
W/W1-and-Y1 or R to W/W1-and-Y1-and-G circuits are
energized, the furnace control CPU will switch to or turn on the
blower motor BLWM at low cool speed (same speed as LO
HEAT), and begin a low-heat cycle. The blower motor BLWM
will remain on until the end of the prepurge period, then shut off
for 24 seconds then come back on at LO HEAT speed. When the
W/W1 input signal disappears, the furnace control begins a
normal inducer post-purge period and the blower remains running
at LO HEAT speed. If the R-to-W/W1-and-Y1-and-G signals
disappear at the same time, the blower motor BLWM will remain
53
352AAV
on for the selected blower-OFF delay period. If the R-to
W/W1-and-Y1 signals disappear, leaving the G signal, the blower
motor BLWM will remain on for the selected blower-OFF
delay period then switch to continuous-blower speed.
When
the
R-to
W/W1-and-Y/Y2,
R-to-W/W1-andY/Y2-and-G, R-to W/W1-and-Y1-and-Y/Y2, or R-to-W/W1and-Y1-and- Y/Y2-and-G circuits are energized the furnace
control CPU will switch to or turn on the blower motor BLWM
at COOL speed, and begin a high-heat cycle. The blower motor
BLWM will remain on until the end of the prepurge period,
then shut off for 24 seconds then come back on at HI HEAT
speed. When the W/W1 input signal disappears, the furnace
control begins a normal inducer post-purge period and the
blower switches to COOL speed after a 3 second delay. If the
R-to-W/W1-and-Y/Y2-and-G or R-to W/W1-and-Y1-andY/Y2-and-G signals disappear at the same time, the blower
motor BLWM will remain on for the selected blower-OFF
delay
period.
If
the
R-to
W/W1-and-Y/Y2
or
R-to-W/W1-and-Y1-and-Y/Y2 signals disappear, leaving the G
signal, the blower motor BLWM will remain on for the selected
blower- OFF delay period then switch to continuousblower speed.
b. When the R to G-and Y/Y2 circuit is closed and there
is a demand for dehumidification, the furnace blower
motor BLWM will drop the blower speed from COOL
to HI HEAT for a maximum of 10 minutes before
reverting back to COOL speed. If there is still a
demand for dehumidification after 20 minutes, the
furnace control CPU will drop the blower speed back
to HI HEAT speed. This alternating 10-minute cycle
will continue as long as there is a call for cooling.
c. When the “call for cooling” is satisfied and there is a
demand for dehumidification, the cooling blower-off
delay is decreased from 90 seconds to 5 seconds.
NOTE: Manifold pressure MUST always be measured with
burner enclosure front REMOVED.
b. Remove regulator seal caps that conceal adjustment
screws for low-and high-heat gas valve pressure
regulators. (See Fig. 58.)
c. Move setup switch SW-1 on control center to ON
position. This keeps furnace locked in low-heat
operation.
d. Jumper R and W/W1 thermostat connections on
control to start furnace.
e. Turn low-heat adjusting screw (3/32 hex Allen wrench)
counterclockwise (out) to decrease input rate or
clock-wise (in) to increase input rate.
NOTE: DO NOT set low-heat manifold pressure less than
1.3-in. wc or more than 1.7-in. wc for natural gas. If manifold
pressure is outside this range, change main burner orifices to
obtain pressure in this range.
6. Operate furnace per instruction on outer door.
7. Verify furnace shut down by lowering thermostat setting
below room temperature.
8. Verify that furnace restarts by raising thermostat setting
above room temperature.
OPERATE FURNACE
Follow procedures on operating instructions label attached
to furnace.
FURNACE RESTART
With furnace operating, set thermostat below room temperature
and observe that furnace goes off. Set thermostat above room
temperature and observe that furnace restarts.
Step 5 -- Adjustments
352AAV
SET GAS INPUT RATE
Furnace gas input rate on rating plate is for installations at
altitudes up to 2000 ft. (610 M).
In the U.S.A., the input ratings for altitudes above 2000 ft (610
M) must be reduced by 2 percent for each 1000 ft. (305 M) above
sea level.
In Canada, the input ratings must be derated by 5 percent for
altitudes of 2001 ft to 4500 ft (610 to 1372 M)above sea level.
Adjust manifold pressure to obtain input rate.
Furnace input rate must be within ± 2 percent of input on furnace
rating plate adjusted for altitude.
1. Determine Natural Gas Orifice Size And Manifold
Pressure For Correct Input.
a. Obtain average gas heat value (at installed altitude)
from local gas supplier.
b. Obtain average gas specific gravity from local gas
supplier.
c. Verify furnace model and size. Table 15 can only be
used for model 352AAV furnaces with heating inputs
of 20,000/13,000 (High/Low) Btuh per burner.
d. Find installation altitude in Table 15.
NOTE: For Canada altitudes of 2001 to 4500 ft. (610 to 1372
M), use U.S.A. altitudes of 2001 to 3000 ft (610 to 914 M) in
Table 15.
e. Find closest natural gas heat value and specific gravity
on Table 15.
f. Follow heat value and specific gravity lines to point of
intersection to find orifice size and manifold pressure
settings for proper operation.
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in reduced
furnace life.
DO NOT bottom out gas valve regulator adjusting screw. This
can result in unregulated manifold pressure and result in
excess overfire and heat exchanger failures.
NOTE: If orifice hole appears damaged or it is suspected to have
been redrilled, check orifice hole with a numbered drill bit of
correct size. Never redrill an orifice. A burr-free and squarely
aligned orifice hole is essential for proper flame characteristics.
f. Move setup switch SW-1 to OFF position after
completing low-heat adjustment.
g. Jumper R and W1 and W2 thermostat connections on
control. (See Fig. 37.) This keeps furnace locked in
high-heat operation.
h. Turn high-heat adjusting screw (3/32 hex Allen
wrench) counterclockwise (out) to decrease input rate
or clockwise (in) to increase rate.
NOTE: DO NOT set high-heat manifold pressure less than
3.2-in. wc or more than 3.8-in. wc for natural gas. If manifold
pressure is outside this range, change main burner orifices to
obtain pressure in this range.
i. When correct input is obtained, replace caps that
conceal gas valve regulator adjustment screws. Main
burner flame should be clear blue, almost transparent.
(See Fig. 59.)
j. Remove jumper R-to-W1 and W2.
EXAMPLE:
(0 -- 2000 ft (0--610 M) altitude using Table 15)
Heating value = 1050 Btu/cu ft
Specific gravity = 0.62
Therefore: Orifice No. 45
Manifold pressure 3.6-in. wc for high heat
1.5-in. wc for low heat
* Furnace is shipped with No. 45 orifices.
In this example all main burner orifices are the correct size
and do not need to be changed to obtain the proper input rate.
!
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in component damage
due to flame impingement of burners and heat exchangers.
DO NOT redrill orifices. Improper drilling (burrs,
out-of-round holes, etc.) can cause excessive burner noise and
misdirection of burner flames. (See Fig. 60.)
g. Check and verify burner orifice size in furnace.
NEVER ASSUME ORIFICE SIZE; ALWAYS CHECK
AND VERIFY.
2. Adjust Manifold Pressure To Obtain Input Rate.
a. Remove burner enclosure front.
54
Table 15 – Model 352AAV Orifice Size and High/Low-Heat Manifold Pressures for Correct Inputs
for Use with 060 Through 120 Size Furnaces Only
(Tabulated Data Based on 20,000/13,000 Btuh per Burner,
Derated 2 Percent for Each 1000 ft (305 M)Above Sea Level)*
0 to
2000
(0 to
610)
0%
derate
U.S.A. and Canada
ALTITUDE
RANGE
FT (M)
U.S.
Altitudes
2001
to 3000
(610 to
914)
or
Canada
Altitudes
2001 to
4500
(610 to
1371)
5%
derate
U.S.A. Only
ALTITUDE
RANGE
FT (M)
3001 to
4000
(914 to
1219)
7%
derate
AVG GAS
HEAT VALUE
(BTU/CU FT)
850
875
900
925
950
975
1000
1025
1050
1075
1100
AVG GAS
HEAT VALUE
(BTU/CU FT)
775
800
825
850
875
900
925
950
975
1000
1025
AVG GAS
HEAT VALUE
(BTU/CU FT)
750
775
800
825
850
875
900
925
950
975
1000
0.58
Orifice
Manifold
no.
Pressure
43
43
44
44
44
44
45
45
45
45
47
Orifice
no.
43
43
44
44
44
44
45
45
45
47
47
Orifice
no.
43
43
44
44
44
45
45
45
45
47
47
3.7/1.5
3.5/1.5
3.7/1.6
3.5/1.5
3.4/1.4
3.2/1.3
3.7/1.6
3.5/1.5
3.3/1.4
3.2/1.3
3.6/1.5
0.58
Manifold
Pressure
3.8/1.6
3.5/1.5
3.8/1.6
3.6/1.5
3.4/1.4
3.2/1.4
3.7/1.5
3.5/1.5
3.3/1.4
3.7/1.6
3.6/1.5
0.58
Manifold
Pressure
3.7/1.6
3.5/1.5
3.7/1.6
3.5/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.4
3.2/1.4
3.6/1.5
3.5/1.5
SPECIFIC GRAVITY OF NATURAL GAS
0.60
0.62
0.64
Orifice
Manifold Orifice
Manifold
Orifice
Manifold
no.
Pressure
no.
Pressure
no.
Pressure
43
43
43
44
44
44
45
45
45
45
47
3.8/1.6
42
3.2/1.4
42
3.3/1.4
3.6/1.5
43
3.7/1.6
43
3.8/12.6
3.4/1.4
43
3.5/1.5
43
3.6/1.5
3.7/1.6
44
3.8/1.6
43
3.4/1.4
3.5/1.5
44
3.6/1.5
44
3.7/1.6
3.3/1.4
44
3.4/1.4
44
3.5/1.5
3.8/1.6
44
3.2/1.4
44
3.4/1.4
3.6/1.5
45
3.7/1.6
44
3.2/1.3
3.4/1.5
45
3.6/1.5
45
3.7/1.6
3.3/1.4
45
3.4/1.4
45
3.5/1.5
3.7/1.6
45
3.2/1.4
45
3.4/1.4
SPECIFIC GRAVITY OF NATURAL GAS
0.60
0.62
0.64
Orifice
Manifold
Orifice
Manifold
Orifice
Manifold
no.
Pressure
no.
Pressure
no.
Pressure
42
43
43
44
44
44
45
45
45
45
47
3.2/1.4
42
3.3/1.4
42
3.4/1.4
3.7/1.5
43
3.8/1.6
42
3.2/1.4
3.4/1.5
43
3.6/1.5
43
3.7/1.5
3.7/1.6
44
3.8/1.6
43
3.5/1.5
3.5/1.5
44
3.6/1.5
44
3.7/1.6
3.3/1.4
44
3.4/1.4
44
3.5/1.5
3.8/1.6
44
3.2/1.4
44
3.3/1.4
3.6/1.5
45
3.7/1.6
45
3.8/1.6
3.4/1.4
45
3.5/1.5
45
3.6/1.5
3.2/1.4
45
3.4/1.4
45
3.5/1.5
3.7/1.6
45
3.2/1.3
45
3.3/1.4
SPECIFIC GRAVITY OF NATURAL GAS
0.60
0.62
0.64
Orifice
Manifold
Orifice
Manifold
Orifice
Manifold
no.
Pressure
no.
Pressure
no.
Pressure
43
43
43
44
44
44
45
45
45
45
47
3.8/1.6
3.6/1.5
3.4/1.4
3.6/1.5
3.4/1.4
3.2/1.4
3.7/1.6
3.5/1.5
3.3/1.4
3.2/1.3
3.6/1.5
* Orifice numbers shown in shading are factory installed.
NOTE: Percents of derate are based on midpoints of U.S. altitude ranges.
55
42
43
43
44
44
44
45
45
45
45
45
3.3/1.4
3.7/1.6
3.5/1.5
3.8/1.6
3.5/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.5
3.3/1.4
3.7/1.6
42
43
43
43
44
44
44
45
45
45
45
3.4/1.4
3.8/1.6
3.6/1.5
3.4/1.4
3.7/1.5
3.5/1.5
3.3/1.4
3.7/1.6
3.5/1.5
3.4/1.4
3.2/1.4
Orifice
no.
42
42
43
43
44
44
44
44
45
45
45
Orifice
no.
42
42
43
43
43
44
44
44
45
45
45
Orifice
no.
42
42
43
43
44
44
44
44
45
45
45
0.66
Manifold
Pressure
3.4/1.4
3.2/1.4
3.7/1.6
3.5/1.5
3.8/1.6
3.6/1.5
3.5/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.5/1.5
0.66
Manifold
Pressure
3.5/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.4
3.6/1.5
3.4/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.4
0.66
Manifold
Pressure
3.5/1.5
3.2/1.4
3.7/1.6
3.5/1.5
3.8/1.6
3.6/1.5
3.4/1.4
3.2/1.3
3.7/1.5
3.5/1.5
3.3/1.4
352AAV
U.S.A. and Canada
ALTITUDE
RANGE
FT (M)
Table 15 -- Model 352AAV Orifice Size and High/Low-Heat Manifold Pressures for Correct Inputs (Continued)
for Use With 060 Through 120 Size Furnaces Only
(Tabulated Data Based on 20,000/13,000 Btuh per Burner,
Derated 2 Percent for Each 1000 ft (305 M) Above Sea Level)*
4001
to
5000
(1219
to
1524)
9%
derate
U.S.A. Only
ALTITUDE
RANGE
FT (M)
5001
to
6000
(1524
to
1829)
11%
derate
ALTITUDE
RANGE
FT (M)
U.S.A. Only
352AAV
U.S.A. Only
ALTITUDE
RANGE
FT (M)
6001
to
7000
(1829
to
2134)
13%
derate
AVG GAS
HEAT
VALUE
(BTU/CU FT)
725
750
775
800
825
850
875
900
925
950
AVG GAS
HEAT
VALUE
(BTU/CU FT)
700
725
750
775
800
825
850
875
900
925
950
975
1000
AVG GAS
HEAT
VALUE
(BTU/CU FT)
650
675
700
725
750
775
800
825
850
875
SPECIFIC GRAVITY OF NATURAL GAS
0.58
Orifice
no.
43
44
44
44
44
45
45
45
47
47
Manifold
Pressure
3.7/1.5
3.4/1.4
3.7/1.6
3.51.5
3.2/1.4
3.5/1.5
3.3/1.4
3.3/1.4
3.7/1.6
3.5/1.5
0.60
Orifice
no.
43
43
44
44
44
45
45
45
45
47
0.58
Orifice
no.
43
43
44
44
44
45
45
45
47
47
48
48
48
Manifold
Pressure
3.6/1.5
3.4/1.4
3.6/1.5
3.4/1.4
3.2/1.3
3.6/1.5
3.4/1.4
3.2/1.4
3.6/1.5
3.4/1.4
3.7/1.6
3.5/1.5
3.3/1.4
0.60
Orifice
no.
43
43
44
44
44
45
45
45
47
47
48
48
48
0.58
Orifice
no.
42
43
44
44
44
45
45
45
47
47
Manifold
Pressure
3.2/1.3
3.6/1.5
3.8/1.6
3.6/1.5
3.3/1.4
3.8/1.6
3.5/1.5
3.3/1.4
3.7/1.6
3.5/1.5
0.62
0.62
0.62
Manifold
Pressure
3.3/1.4
3.7/1.6
3.4/1.5
3.7/1.6
3.4/1.5
3.2/1.4
3.7/1.5
3.4/1.5
3.2/1.4
3.6/1.5
* Orifice numbers shown in shading are factory installed.
NOTE: Percents of derate are based on midpoints of U.S. altitude ranges.
56
Orifice
no.
42
43
43
44
44
44
45
45
45
45
Manifold
Pressure
3.4/1.4
3.8/1.6
3.6/1.5
3.8/1.6
3.6/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.4
3.2/1.3
Manifold
Pressure
3.3/1.4
3.8/1.6
3.5/1.5
3.8/1.6
3.6/1.5
3.4/1.4
3.2/1.3
3.6/1.5
3.4/1.5
3.3/1.4
0.66
Orifice
no.
42
42
43
43
44
44
44
45
45
45
Manifold
Pressure
3.4/1.4
3.2/1.4
3.7/1.5
3.4/1.4
3.7/1.6
3.5/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.4
Orifice
no.
42
43
43
43
44
44
44
45
45
45
47
47
48
Manifold
Pressure
3.4/1.4
3.8/1.6
3.6/1.5
3.4/1.4
3.6/1.5
3.4/1.4
3.2/1.4
3.7/1.5
3.5/1.5
3.3/1.4
3.7/1.6
3.5/1.5
3.8/1.6
Orifice
no.
42
42
43
43
44
44
44
45
45
45
Manifold
Pressure
3.6/1.6
3.3/1.4
3.8/1.6
3.5/1.5
3.8/1.6
3.5/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.4
0.64
Manifold
Orifice
Manifold
Orifice
Pressure
no.
Pressure
no.
3.7/1.6
42
3.2/1.3
42
3.5/1.5
43
3.6/1.5
43
3.7/1.6
43
3.4/1.4
43
3.5/1.5
44
3.6/1.5
44
3.3/1.5
44
3.4/1.4
44
3.7/1.6
44
3.2/1.4
44
3.5/1.5
45
3.6/1.5
45
3.3/1.4
45
3.4/1.5
45
3.7/1.6
45
3.3/1.4
45
3.5/1.5
47
3.7/1.5
45
3.8/1.6
47
3.5/1.5
47
3.6/1.5
48
3.8/1.6
47
3.5/1.5
48
3.6/1.5
48
SPECIFIC GRAVITY OF NATURAL GAS
0.60
Orifice
no.
42
43
43
44
44
44
45
45
45
47
0.64
Manifold
Orifice
Manifold
Orifice
Pressure
no.
Pressure
no.
3.8/1.6
42
3.2/1.4
42
3.5/1.5
43
3.7/1.5
43
3.8/1.6
43
3.4/1.4
43
3.6/1.5
44
3.7/1.6
44
3.4/1.4
44
3.5/1.5
44
3.8/1.6
44
3.3/1.4
44
3.6/1.5
45
3.7/1.6
44
3.4/1.4
45
3.5/1.5
45
3.2/1.4
45
3.3/1.4
45
3.6/1.5
45
3.2/1.3
45
SPECIFIC GRAVITY OF NATURAL GAS
Manifold
Pressure
3.3/1.4
3.7/1.6
3.5/1.5
3.7/1.6
3.5/1.5
3.3/1.4
3.8/1.6
3.6/1.5
3.4/1.4
3.2/1.3
3.6/1.5
3.4/1.4
3.7/1.6
0.66
0.64
Orifice
no.
42
42
43
43
44
44
44
45
45
45
Manifold
Pressure
3.5/1.5
3.2/1.4
3.7/1.6
3.4/1.4
3.7/1.6
3.4/1.5
3.2/1.4
3.7/1.6
3.5/1.5
3.3/1.4
0.66
Table 15 -- Model 352AAV Orifice Size and High/Low-Heat Manifold Pressures for Correct Inputs (Continued)
for Use With 060 Through 120 Size Furnaces Only
(Tabulated Data Based on 20,000/13,000 Btuh per Burner,
Derated 2 Percent for Each 1000 ft (305 M) Above Sea Level)*
U.S.A. Only
FT (M)
7001
to
8000
(2134 to
2438)
15%
derate
ALTITUDE
RANGE
U.S.A. Only
FT (M)
Altitudes
8001
to 9000
(2438 to
2743)
17%
derate
ALTITUDE
RANGE
U.S.A. Only
FT (M)
9001
to
10000
(2743
to
3048)
19%
derate
AVG GAS
HEAT
VALUE
(BTU/CU FT)
625
650
675
700
725
750
775
800
825
850
AVG GAS
HEAT
VALUE
(BTU/CU FT)
600
625
650
675
700
725
750
775
800
AVG GAS
HEAT
VALUE
(BTU/CU FT)
575
600
625
650
675
700
725
750
775
SPECIFIC GRAVITY OF NATURAL GAS
0.58
Orifice
Manifold
no.
Pressure
43
3.8/1.6
43
3.5/1.5
44
3.8/1.6
44
3.5/1.5
44
3.3/1.4
45
3.7/1.6
45
3.5/1.5
45
3.3/1.4
47
3.6/1.5
47
3.4/1.4
0.60
Orifice
Manifold
no.
Pressure
42
3.3/1.4
43
3.7/1.6
43
3.4/1.4
44
3.6/1.5
44
3.4/1.4
45
3.8/1.6
45
3.6/1.5
45
3.4/1.4
45
3.2/1.3
47
3.5/1.5
0.58
Orifice
Manifold
no.
Pressure
43
3.8/1.6
43
3.5/1.5
44
3.7/1.6
44
3.5/1.5
44
3.2/1.4
45
3.6/1.5
45
3.4/1.4
45
3.2/1.3
47
3.6/1.5
0.60
Orifice
Manifold
no.
Pressure
42
3.3/1.4
43
3.6/1.5
43
3.4/1.4
44
3.6/1.5
44
3.3/1.4
45
3.8/1.6
45
3.5/1.5
45
3.3/1.4
47
3.7/1.6
0.58
Orifice
Manifold
no.
Pressure
43
3.8/1.6
43
3.5/1.5
44
3.7/1.6
44
3.4/1.4
44
3.8/1.6
45
3.6/1.5
45
3.3/1.4
47
3.7/1.6
47
3.5/1.5
0.60
Orifice
Manifold
no.
Pressure
42
3.2/1.4
43
3.6/1.5
44
3.8/1.6
44
3.5/1.5
44
3.3/1.4
45
3.7/1.6
45
3.4/1.5
45
3.2/1.4
47
3.6/1.5
Orifice
no.
42
43
43
44
44
44
45
45
45
47
0.62
Manifold
Pressure
3.4/1.4
3.8/1.6
3.5/1.5
3.8/1.6
3.5/1.5
3.3/1.4
3.7/1.6
3.5/1.5
3.3/1.4
3.7/1.5
Orifice
no.
42
42
43
43
44
44
45
45
45
45
0.64
Manifold
Pressure
3.5/1.5
3.2/1.4
3.6/1.5
3.4/1.4
3.6/1.5
3.4/1.4
3.8/1.6
3.6/1.5
3.4/1.4
3.2/1.3
Orifice
no.
42
42
43
43
44
44
44
45
45
45
0.66
Manifold
Pressure
3.6/1.5
3.3/1.4
3.7/1.6
3.5/1.5
3.7/1.6
3.5/1.5
3.3/1.4
3.7/1.6
3.5/1.5
3.3/1.4
0.64
Manifold
Pressure
3.5/1.5
3.2/1.4
3.6/1.5
3.8/1.6
3.6/1.5
3.3/1.4
3.8/1.6
3.5/1.5
3.3/1.4
Orifice
no.
42
42
43
43
44
44
44
45
45
0.66
Manifold
Pressure
3.6/1.5
3.3/1.4
3.7/1.6
3.4/1.5
3.7/1.6
3.4/1.4
3.2/1.4
3.6/1.5
3.4/1.4
0.64
Manifold
Pressure
3.3/1.5
3.2/1.3
3.6/1.5
3.8/1.6
3.5/1.5
3.3/1.4
3.7/1.6
3.4/1.5
3.2/1.4
Orifice
no.
42
42
43
43
44
44
45
45
45
0.66
Manifold
Pressure
3.6/1.5
3.3/1.4
3.7/1.6
3.4/1.4
3.6/1.5
3.4/1.4
3.8/1.6
3.5/1.5
3.3/1.4
SPECIFIC GRAVITY OF NATURAL GAS
Orifice
no.
42
43
43
44
44
44
45
45
45
0.62
Manifold
Pressure
3.4/1.4
3.8/1.6
3.5/1.5
3.7/1.6
3.4/1.5
3.2/1.4
3.6/1.5
3.4/1.4
3.2/1.3
Orifice
no.
42
42
43
44
44
44
45
45
45
SPECIFIC GRAVITY OF NATURAL GAS
*Orifice numbers shown in shading are factory installed.
NOTE: Percents of derate are based on midpoints of U.S. altitude ranges.
57
Orifice
no.
42
43
43
44
44
45
45
45
47
0.62
Manifold
Pressure
3.3/1.4
3.7/1.6
3.5/1.5
3.7/1.5
3.4/1.4
3.8/1.6
3.6/1.5
3.3/1.4
3.7/1.6
Orifice
no.
42
42
43
44
44
44
45
45
45
352AAV
ALTITUDE
RANGE
INLET
PRESSURE
TAP
FF
NOTE: Be sure all pressure tubing, combustion-air and vent
pipes, and burner enclosure front are in place when checking
input by clocking gas meter.
a. Calculate high-altitude adjustment (if required).
UNITED STATES
At altitudes above 2000 ft, this furnace has been
approved for 2 percent derate for each 1000 ft above
sea level. See Example and Table 16 for derate
multiplier factor.
LOW-FIRE
ADJUSTMENT
ALLEN SCREW
(UNDER CAP)
ON/OFF
SWITCH
HIGH-FIRE
ADJUSTMENT
ALLEN SCREW
(UNDER CAP)
O
ON
EXAMPLE:
100,000 Btuh input furnace installed at 4300 ft.
Furnace Input Rate
at Sea Level
X
100,000
X
Derate
Multiplier
=
Factor
0.91
Furnace Input Rate
at Installation
Altitude
=
91,000
352AAV
CANADA
At installation altitudes from 2001 to 4500 ft, this
furnace must be derated 5 percent by an authorized Gas
Conversion Station or Dealer. To determine correct
input rate for altitude, see example above and use 0.95
as derate multiplier factor.
b. Reinstall burner box cover.
NOTE: Clocking gas input rate MUST always be performed
with the burner box cover INSTALLED.
c. Check that gas valve adjustment caps are in place for
proper input to be clocked.
d. Obtain yearly heat value average for local gas supply.
NOTE: Be sure heating value of gas used for calculations is
correct for your altitude. Consult local gas utility for altitude
adjustment of gas heating value.
e. Check and verify orifice size in furnace. NEVER
ASSUME THE ORIFICE SIZE. ALWAYS CHECK
AND VERIFY.
f. Turn off all other gas appliances and pilots.
g. Move setup switch SW-1 to ON position. This keeps
furnace locked in low-heat operation.
h. Jumper R-to-W/W1.
i. Let furnace run for 3 minutes in low-heat operation.
j. Measure time (in sec) for gas meter to complete 1
revolution. Note reading.
k. Refer to Table 17 for cubic ft of gas per hr.
l. Multiply gas rate cu ft/hr by heating value (Btu/cu ft).
m. Move setup switch SW-1 to OFF position and jumper
R and W1 and W2 thermostat connections. This keeps
furnace locked in high-heat operation. Repeat items ‘i’
through ‘l’ for high-heat operation.
MANIFOLD
PRESSURE
TAP
;;
;;
A97358
Fig. 58 -- Redundant Automatic Gas Control Valve
BURNER FLAME
BURNER
MANIFOLD
A89020
Fig. 59 -- Burner Flame
Example:
(0 -- 2000 ft altitude)
Furnace input from rating plate is 100,000 Btuh.
Btu heating input = Btu/cu ft X cu ft/hr
Heating value of gas = 975 Btu/cu ft
Time for 1 revolution of 2-cu ft dial = 70 sec
Gas rate = 103 cu ft/hr (from Table 17)
Btu heating input = 103 X 975 = 100,425 Btuh. In this
example, the orifice size and manifold pressure adjustment
is within ±2 percent of the furnace input rate.
BURNER
ORIFICE
NOTE: Measured gas inputs (high-heat and low-heat) must be
within ±2 percent of that stated on furnace rating plate when
installed at sea level or derated per that stated above when
installed at higher altitudes.
n. Remove jumper across R, W/W1, and W2 thermostat
connections to terminate call for heat.
A93059
Fig. 60 -- Burner Orifice
3. Verify Natural Gas Input Rate By Clocking Gas Meter.
58
Table 16 – Altitude Derate Multiplier for USA.
PERCENT OF
DERATE
DERATE MULTIPLIER
FACTOR*
0
1.00
4---6
0.95
6---8
0.93
8---10
0.91
10---12
0.89
12---14
0.87
14---16
0.85
16---18
0.83
18---20
0.81
!
UNIT DAMAGE HAZARD
Failure to follow this caution may result in overheating the
heat exchangers or condensing flue gases in heat exchanger
areas not designed for condensate.
Temperature rise must be within limits specified on furnace
rating plate. Recommended operation is at midpoint of rise
range or slightly above.
Place SW-1 in ON position. Jumper R to W/W1 and W2 to check
high-gas-heat temperature rise. To check low-gas-heat
temperature rise, remove jumper to W2. Determine air
temperature rise for both high and low gas heat. Do not exceed
temperature rise ranges specified on unit rating plate for high and
low gas heat.
This furnace must operate within the temperature rise ranges
specified on the furnace rating plate. Determine the air
temperature as follows:
a. Place duct thermometers in return and supply ducts as
close to furnace as possible. Be sure thermometers do
not “see” heat exchangers so that radiant heat does not
affect thermometer readings. This is particularly
important with straight run ducts.
b. When thermometer readings stabilize, subtract
return-air temperature from supply-air temperature to
determine temperature rise.
If the temperature rise is outside this range, check the following:
a. Gas input for low-and high gas heat operation.
b. Derate for altitude if applicable.
c. Return and supply ducts for excessive restrictions
causing static pressures greater than 0.50-in. wc.
d. Adjust temperature rise by adjusting blower speed.
Increase blower speed to reduce temperature rise.
Decrease blower speed to increase temperature rise.
* Derate multiplier factors are based on midpoint altitude for altitude range.
Table 17 – Gas Rate (CU FT/HR)
SECONDS
FOR 1
REVOLUTION
SIZE OF TEST
DIAL
10
1
Cu Ft
360
2
Cu Ft
720
5
Cu Ft
1800
11
327
655
1636
12
300
600
1500
13
277
555
14
257
15
SECONDS
FOR 1
REVOLUTION
CAUTION
SIZE OF TEST
DIAL
50
1
Cu Ft
72
2
Cu Ft
144
5
Cu Ft
360
51
71
141
355
52
69
138
346
1385
53
68
136
340
514
1286
54
67
133
333
240
480
1200
55
65
131
327
16
225
450
1125
56
64
129
321
17
212
424
1059
57
63
126
316
18
200
400
1000
58
62
124
310
19
189
379
947
59
61
122
305
20
180
360
900
60
60
120
300
21
171
343
857
62
58
116
290
22
164
327
818
64
56
112
281
23
157
313
783
66
54
109
273
24
150
300
750
68
53
106
265
25
144
288
720
70
51
103
257
26
138
277
692
72
50
100
250
27
133
267
667
74
48
97
243
28
129
257
643
76
47
95
237
29
124
248
621
78
46
92
231
30
120
240
600
80
45
90
225
31
116
232
581
82
44
88
220
32
113
225
563
84
43
86
214
33
109
218
545
86
42
84
209
34
106
212
529
88
41
82
205
35
103
206
514
90
40
80
200
36
100
200
500
92
39
78
196
37
97
195
486
94
38
76
192
38
95
189
474
96
38
75
188
39
92
185
462
98
37
74
184
40
90
180
450
100
36
72
180
41
88
176
439
102
35
71
178
42
86
172
429
104
35
69
173
43
84
167
419
106
34
68
170
44
82
164
409
108
33
67
167
45
80
160
400
110
33
65
164
46
78
157
391
112
32
64
161
47
76
153
383
116
31
62
155
48
75
150
375
120
30
60
150
49
73
147
367
124
29
58
145
!
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
Disconnect 115-v electrical power before changing speed tap.
For high-heat, the following connections can be made at HI
HEAT on control:
a. Med-high (Yellow)
b. Med (Orange) -- Available only on 5-speed motors.
Factory setting for these motors.
c. Med-Low(Blue) -- Do NOT use for HI GAS-HEAT
on 80K & 120K Btuh input models. Factory setting
for 4-speed motors.
59
352AAV
ALTITUDE
FT (M)
0–2000
(0 --- 610)
2001–3000
(610 --- 914)
3001–4000
(914 --- 1219)
4001–5000
(1219 --- 1524)
5001–6000
1524 --- 1829)
6001–7000
(1829 --- 2134)
7001–8000
(2134 --- 2438)
8001–9000
(2438 --- 2743)
9001–10,000
(2743 --- 3048)
SET TEMPERATURE RISE
!
Step 6 -- Check Safety Controls
CAUTION
This section covers the safety controls that must be checked
before the installation is complete. The flame sensor, gas valve,
and pressure switch were all checked in the Start-up procedure
section as part of normal operation.
1. Check Primary Limit Control
This control shuts off gas control system and energizes
air-circulating blower motor if furnace overheats.
Recommended method of checking this limit control is to
gradually block off return air after furnace has been
operating for a period of at least 5 minutes. As soon as
limit control has shut off burners, return-air opening
should be unblocked to permit normal air circulation. By
using this method to check limit control, it can be
established that limit is functioning properly and operates
if there is a restricted return-air supply or motor failure. If
limit control does not function during this test, cause must
be determined and corrected.
UNIT DAMAGE HAZARD
Failure to follow this caution may result in damage to the heat
exchangers due to over temperature or condensate corrosion.
1. NEVER connect Low Speed (Red) wire to “HI HEAT”.
2. Do NOT connect Medium Low Speed (Blue) wire to
“HI-HEAT” on 80,000 Btuh and 120,000 Btuh input
model sizes.
352AAV
Table 18 – Speed Selection
LEAD COLOR
White
Black
Yellow
Orange†
Blue
Red
SPEED
Common
High
Med---High
Med
Med---Low
Low*
AS SHIPPED
COM
Cool
SPARE
High---Gas Heat
Spare/High---Gas Heat
Low---Gas Heat
THERMOSTAT SUBBASE
TERMINALS WITH
THERMOSTAT REMOVED
* Continuous blower speed
† Available on 5-speed blowers only
HOOK-AROUND
VOLT/AMMETER
For low-heat, the following connections can be made at LOHEAT on control:
a. Med (Orange) -- Available only on 5-speed motors
b. Med-Low (Blue)
c. Low (RED) -- Factory setting.
To change blower motor speed selections for heating mode,
remove blower motor lead from control HI-HEAT terminal. (See
Fig. 37.) Select desired blower motor speed lead from one of the
other motor leads and relocate it to HI-HEAT terminal. See Table
18 for lead color identification. Reconnect original lead on
SPARE terminal. Follow this same procedure for proper selection
of LO-HEAT and COOL speed selection.
Set Blower Off Delay
a. Remove Blower Access Door if installed.
b. Turn Dip switch 2 and 3 ON or OFF for desired
blower off delay. See Table 11 and 12 or Fig. 36
and 37.
R Y W G
10 TURNS
FROM UNIT 24-VOLT
TERMINAL BLOCK
EXAMPLE: 5.0 AMPS ON AMMETER
10 TURNS AROUND JAWS
= 0.5 AMPS FOR THERMOSTAT SETTING
A80201
ADJUST BLOWER OFF DELAY (HEAT MODE)
Fig. 61 -- Amp Draw Check with Ammeter
If desired, the main blower off time delay period may be
lengthened or shortened when operating in the heating mode to
provide greater comfort. See Table 11 for position of switches
and Fig. 36 or 37 for location of switches on control center.
2. Check Pressure Switch
This control proves operation of draft inducer. Check switch
operation as follows:
a. Turn off 115-v power to furnace.
b. Remove outer furnace door and disconnect inducer
motor lead wires from wire harness.
c. Turn on 115-v power to furnace.
d. Set thermostat to “call for heat” and wait 1 minute.
When pressure switch is functioning properly, hot
surface igniter should not glow, and status code LED
flashes a Status Code 32. If hot surface ignitor glows
when inducer motor is disconnected, shut furnace
down immediately. Determine reason pressure switch
did not function properly and correct condition.
e. Turn off 115-v power to furnace.
f. Reconnect inducer motor leads, reinstall main furnace
door, and turn on 115-v power supply.
SET THERMOSTAT HEAT ANTICIPATOR
When using a nonelectronic thermostat, the thermostat
heat-anticipator must be set to match the amp draw of
the electrical components in R-W/W1 circuit. Accurate amp
draw readings can be obtained at thermostat subbase terminals
R and W.
Fig. 61 illustrates an easy method of obtaining actual amp draw.
The amp reading should be taken after blower motor has started
and furnace is operating in low heat. To operate furnace in
low-heat, first move SW-1 to ON position, then connect ammeter
wires as shown in Fig. 61. The thermostat anticipator should
NOT be in the circuit while measuring current. If thermostat has
no subbase, the thermostat must be disconnected from R and
W/W1 wires during current measurement Return SW-1 to final
desired location after completing the reading.
See thermostat manufacturer’s instructions for adjusting heat
anticipator and for varying heating cycle length.
When using an electronic thermostat, set cycle rate for 3 cycles
per hour.
60
CHECKLIST
1. Put away tools and instruments. Clean up debris.
2. Check SW-1 through SW-3 after completing installation to
ensure desired settings for thermostat type (SW-1) and
blower-OFF delay (SW-2 and SW-3).
3. Verify flame rollout manual reset switch has continuity.
4. Verify that blower and outer doors are properly installed.
5. Cycle test furnace with room thermostat.
6. Check operation of accessories per manufacturer’s
instructions.
7. Review User’s Guide with owner.
8. Leave literature packet near furnace.
LOAD CALCULATION
Condensate Drain
____________
____________
Unit Level or Pitched Forward
____________
Internal Tubing Connections Free of
Kinks and Traps
____________
External Drain Connection
Leak Tight and Sloped
____________
Condensate Trap Primed before Start-Up
____________
Heat Tape Installed if Required
Heating Load (Btuh)
____________
Cooling Load (Btuh)
____________
Furnace Model Selection
COMBUSTION AIR AND VENT PIPING
Termination Location
____________
Roof or Sidewall
____________
Termination Kit --- 2 Pipe or Concentric
____________
Combustion-Air Pipe Length
____________
CHECKLIST -- START-UP
Combustion-Air Pipe Elbow Quantity
____________
Vent Pipe Length
____________
Vent Pipe Elbow Quantity
____________
Pipe Diameter Determined from Sizing Table
____________
Pipe Sloped To Furnace
Over Ceilings ________
____________
Low-Ambient Exposed Pipes
Gas Input Rate
(Set Within 2 percent of Rating Plate)
____________
Temperature Rise Adjusted
Thermostat Anticipator
____________
Anticipator Setting Adjusted or
____________
Cycle Rate (3 Cycles per Hr) Selected
Safety Controls Check Operation
Pipe Insulation
____________
____________
61
____________
Primary Limit
____________
Pressure Switch
352AAV
CHECKLIST—DIRECT VENT (2-PIPE) INSTALLATION
CHECKLIST -- NON DIRECT VENT (1-PIPE) INSTALLATION
LOAD CALCULATION
Condensate Drain
____________
Heating Load (Btuh)
____________
Unit Level or Pitched Forward
____________
Cooling Load (Btuh)
____________
____________
Furnace Model Selection
Internal Tubing Connections
Free of Kinks and Traps
____________
External Drain Connection Leak Tight and
Sloped
____________
Condensate Trap Primed before Start-Up
____________
Heat Tape Installed if Required
VENT PIPING
352AAV
Termination Location
____________
Roof or Sidewall
____________
Vent Pipe Length
____________
Vent Pipe Elbow Quantity
____________
____________
CHECKLIST—START-UP
____________
Gas Input Rate
(Set Within 2 percent of Rating Plate)
Pipe Diameter Determined from Sizing Table
____________
Temperature Rise Adjusted
Pipe Sloped To Furnace
Thermostat Anticipator
Pipe Insulation
____________
Anticipator Setting Adjusted or
Cycle Rate (3 Cycles per Hr) Selected
____________
Over Ceilings
____________
____________
Low-Ambient Exposed Pipes
Safety Controls Check Operation
E2008 Bryant Heating & Cooling Systems D 7310 W. Morris St. D Indianapolis, IN 46231
____________
Primary Limit
____________
Pressure Switch
Printed in U.S.A.
Edition Date: 12/08
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
62
Catalog No. II352A --- 60 --- 2
Replaces: II352A---60---1
Download PDF