COMBO A L A R M SMOKE & CO SCO2B/SCO2LB

COMBO A L A R M SMOKE & CO SCO2B/SCO2LB
SMOKE & CO
COMBO
ALARM
CAT.
SCO2B/SCO2LB
9V Battery Powered
Description:
10YR CO SENSOR
10YR ALARM LIFE
SMOKE & CO COMBO
Electrochemical CO sensor; Ionization
smoke sensor.
SILENCE FEATURE
Silences nuisance alarms.
END OF LIFE SIGNAL
Provides audible notice when alarm
needs to be replaced after 10 years.
LATCHING ALARM
INDICATOR
Remembers which unit initiated an alarm.
Available in the following versions:
SCO2B Alkaline Battery
SCO2LB
Long Life Lithium battery
The BRK Brands, Inc. model No SCO2 is a battery powered single station combination smoke and carbon monoxide alarm specifically designed for residential
and institutional applications including sleeping rooms of hospitals, hotels, motels,
dormitories and other multi-family dwellings as defined in standard NFPA 101
Model SCO2 complies with UL217, UL2034, CSFM, NFPA 72, NFPA 720, HUD, FHA
and other agencies that model their codes after the above agencies. They meet
building codes where battery powered smoke and carbon monoxide alarms are
required either separately or in combination.
The BRK cat. number SCO2B/SCO2LB features a dual ionization smoke sensing
chamber and an electrochemical carbon monoxide sensor, 9V battery powered,
an 85dB horn, an End of Life and a silence feature. The SCO2B features a 9V alkaline battery and the SCO2LB a 9V long life lithium battery. “Intelligent Sensing
Technology” is designed to reduce nuisance alarms. “Latching Alarm Indicator”
remembers which unit initiated an alarm. The unit that triggered the alarm will
store in memory or “latch” the information and begin to flash the LED indicator 2
seconds on, 2 seconds off. The “Perfect Mount” system features a gasketless base
and a mounting bracket that keeps the alarm secure over a wide rotation range to
allow for true alignment. A single button test/silence button eliminates confusion.
Battery installation and removal can occur while the unit is mounted to the ceiling
or wall via the side load battery compartment. Other Contractor Preferred features
include a dust cover to keep alarm clean during construction. Two locking features
are provided to prevent battery theft and/or theft of the unit. Designed for wall or
ceiling mounting. Includes mounting anchors and screws.
CAT.
SCO2B/SCO2LB
TOP VIEW
TECHNICAL SPECS
MOUNTING
BRACKET
SIDE VIEW
5.6”
2.0”
ARCHITECTURAL AND ENGINEERING SPEC
The combination smoke and CO alarm shall be a BRK Model SCO2 and shall provide at a
minimum the following features and functions:
1. An ionization smoke sensing chamber and an electrochemical CO sensor both with a
10 year service life.
2. Powered by a supervised 9V battery (SCO2B uses alkaline, SCO2LB lithium) and
features a solid state piezo horn rated at 85dB at 10 ft. and the unit shall be capable of
self restoring.
3. The unit shall perform self diagnostic tests and issue a malfunction warning (three
chirps) if the unit malfunctions.
4. The unit shall have an “End of Life” signal (5 chirps). This signal should be capable of
temporarily being silenced for up to 2 days. After about 2 days, the signal will resume.
After about 2-3 weeks the signal cannot be silenced.
5. A visual power-on indicator to confirm unit is receiving power. Separate LED ‘s to
indicate a smoke or CO alarm.
6. The CO sensor is adjusted not to detect CO levels below 30 PPM and will not alarm
when exposed to constant levels of 30 PPM for 30 days. It will alarm at the following
levels: 400 PPM CO between 4 and 15 minutes, 150 PPM CO between 10 and 50
minutes and 70 PPM CO between 60 and 240 minutes.
7. Two Latching features: Alarm Latch to easily identify initiating alarm after alarm
condition has subsided. Low battery latch: to visually identify which unit is in low
battery condition. Two Silence Features: Alarm Silence to temporarily silence nuisance
alarms. Low Battery Silence to silence low battery chirp for up to 8 hours.
8. Two Locking features - tamper resistant locking pins that lock battery drawer and/or alarm to mounting bracket.
9. The unit shall be capable of operating between 40°F (4°C) and 100°F (38°C) and
relative humidity between 10% and 95%.
10. The unit shall contain mounting hardware and shall be listed for wall or ceiling
mounting.
11. The unit shall at a minimum meet the requirements of UL217 and UL2034, CSFM,
NFPA 72 and 720 and the ICC.
INSTALLATION OF ALARM
Installation of this smoke alarm must conform to NFPA 72. Always check your local
building codes. Follow all instructions for placement as outlined in the user’s manual.
THE PARTS OF THIS SMOKE ALARM
3.
4.
5.
TOP OF ALARM
Test/Silence Button
Power Light (Green)/Smoke
Alarm light (Red)
CO Alarm Light (Red)
Battery Drawer
Behind Cover: Alarm 85 dB horn
1.
2.
3.
4.
5.
6.
BOTTOM OF ALARM
Mounting bracket
Mounting slots
Locking Pins
Battery Drawer Latch
Battery Drawer - Install
9V battery here
1.
2.
1
2
4
SHIPPING SPECS
Individual Carton Dimensions 5.69”L x 2.25”W x 5.59”H
Weight 0.59 lbs.
Cube 0.04 ft3
UPC 0 29054 00089 7: SCO2B
0 29054 00736 0: SCO2LB
Master Carton Dimensions 14.43”L x 6.19”W x 12.63”H
Master Pack
12
Weight 7.6 lbs.
Cube: 0.65 ft3
I2of5: 200 29054 00089 1: SCO2B
800 29054 00736 6: SCO2LB
Pallet Information Cases per Layer
19
Number of Layers: 3
Cases per Pallet: 57
Units per Pallet: 684
Cube: 42.2 ft3
Weight: 498 lbs.
BATTERY DRAWER LOCK
Remove Pin from
Mounting Bracket
Close Door. Insert Pin in Holes
through alarm and Battery Drawer
3
2
3
Alarm Dimensions: 5.6”dia. x 2.0”H
Weight: 7.6 oz
Operating Voltage: 9V battery powered (alkaline or lithium)
Temperature Range: 40°F (4°C) to 100°F (38°C)
Humidity Range:
10% to 95% relative humidity (RH)
Audio Alarm:
85dB at 10 feet
Test/Silence:
Electronically simulates smoke or CO condition, causing the unit to alarm. Press and hold test/silence button.
Alarm Reset:
Automatic when smoke or CO clears
Smoke Sensor:
Dual Ionization
CO Sensor:
Electrochemical
Indicator Lights/Sounds:
DC Power: Intermittent Green LED
Local Alarm: Red LED flashes rapidly
Latching Alarm: Red LED flashes 2 sec. on/2 sec. off after local alarm
Low Battery Latch: Green LED flashes on for 2 seconds, off for 2 seconds.
Note: Latching features are active for 15 minutes only.
Listing:
Listed to UL217 and UL2034 Standards
©2015 BRK Brands, Inc. a Jarden Corporation
Company (NYSE: JAH)
3901 Liberty Street Road
Aurora, IL 60504-8122
All rights reserved
5
brkelectronics.com
First Alert is a registered trademark of the First Alert Trust
BRK is a registered trademark of BRK Brands, Inc.
CM3236
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement