Bematech | SB9011D | User manual | Bematech SB9011D User manual

SB9011D All-in-one Touch POS Terminal
USER MANUAL
Table of Contents
1
Overview ............................................................................................ 2
1.1
1.2
Safety Information ........................................................................................ 2
Electromagnetic compatibility statement ................................................. 3
2 Installation Guide ............................................................................. 4
2.1
2.2
Appearances.................................................................................................... 4
Rear panel I/O connectors ............................................................................. 5
3 Setup and Driver Installation ........................................................... 6
3.1
3.2
Motherboard BIOS settings .......................................................................... 6
Touch screen driver installation: .................................................................. 8
4 Troubleshooting ............................................................................... 16
5 Specifications ................................................................................... 19
1
1 Overview
Thank you for purchasing the SB9011D all-in-one touch POS terminal, Bematech is
committed to continuously improve product quality and provide better
after-sales service. In order to take full advantage of our devices, we strongly
recommend that you take the time to read this manual before diving into
software solution.
Note:
Information in this manual may change without prior notice.
1.1 Safety Information
 Before plug in the product, please make sure the power you provide
meets the power requirements (such as voltage, frequency); Make sure
the ground terminal of the power outlet is working properly.
 Lightning may damage this product.
During lightning storms, unplug
the network cable, power cable and any other connections.
 Turn off power before connecting any devices (except USB devices) to the
terminal.
 Do not attempt to open the chassis. You may be hurt by electric shock.
For service, call your place of purchase.
 Do not spill liquid on the terminal.
Do not place any objects into the
ventilation holes of this product. It may cause short-circuit of the internal
components and cause a fire or electric shock.
 After the computer is stored below temperature of 10 ° C, please place the
machine in room temperature (10-35 ° C) in the original packing for at
least two hours to allow the terminal to restore to room temperature
before operation.
This is to avoid condensation that might bring
electrical damage.

Keep the terminal clean, dry, and away from dust, moisture and direct
sunlight.
 Do not use harsh chemicals or strong cleaning solvents to clean the
2
monitor screen. Wipe it clean with a soft terry cloth applied with a mild
solution
 Do not share the same power outlet with high-power electrical appliances;
keep distance from high level magnetic interference.

Do not the use sharp pointed objects to work with the touch screen to
avoid damage to the screen.
When the following occurs:
 Liquid gets inside the POS terminal;
 Accidental physical damage;
 POS terminal produces a burning smell;
Immediately disconnect the power supply, unplug the power cord, and
contact a qualified service technician.
1.2 Electromagnetic compatibility statement
FCC NOTICE
This device complies with Part 15 of FCC Rules. Operations are subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
EUROPEAN COMMUNITY (CE) MARK OF CONFORMITY
This product is in conformity with the protection requirements of EU Council
Directive 89/336/EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. Logic Controls cannot accept
responsibility for any failure to satisfy the protection requirements resulting
from a non-recommended modification of the product. This product has
been tested and found to comply with the limits for Class A Information
Technology Equipment according to CISPR 22 / European Standard EN 55022.
The limits for Class A equipment were derived for commercial and industrial
environments to provide reasonable protection against interference with
licensed communication equipment.
3
2 Installation Guide
2.1 Appearances
4
2.2 Rear panel I/O connectors
At the rear panel of the SB9011D is a row of external I/O device connectors
detailed as follows:
POWER key: Turn power on/off
MOUSE: Connection to PS/2 mouse
KB: Connection to PS/2 keyboard
LPT: DB25 parallel port for connection to POS printer
VGA: VGA signal output for connection to external monitor
COM 1.3.4.5.6: DB9 port for connection to serial devices
USB: Connection to USB devices
LAN1: RJ-45 Ethernet connection to 100M-bit LAN
LAN2: RJ-45 Ethernet connection to Giga-bit LAN
LINE OUT: Stereo phone jack audio output
MIC IN: Microphone input
12V DC IN: Connection to 12V DC Power Supply
5
3 Setup and Driver Installation
3.1 Motherboard BIOS settings
The POS terminal has a BIOS (Basic Input Output System) chip on the
motherboard. Every time you start the terminals, the system will first run the
BIOS self-test routine to check the main components of the system to ensure it is
working properly.
The terminal is loaded with default BIOS settings in the factory. Please do not
change the parameters in the BIOS unless necessary.
In the following situations, you need to run the BIOS setup:
1)
Error message appears on the screen during the system self-test and
requested to enter BIOS setup.
a. Press F1 to run setup; or
b. Press F2 to load default values and continue
2) If you need to change the factory default settings to customized application
requirements.
a. During system boot, hit DEL key to enter BIOS setup.
b. If the message disappears before you respond to, you can turn off the
machine and restart the computer. You can also press <Ctrl> + <Alt> + <Del>
to restart.
Control keys
<↑> Move up
<↓> Move down
<←> Move left
<→> Move right
<Enter> To select this option
<Esc> To exit the menu or to return to the main menu from the submenu
<+/PU> Increase the value or change selection
<-/PD> Reduce the value or change selection
<F1> Help, only available in the status menu and select templates menu
<F9> To load defaultl settings
<F10> To store settings and exit the CMOS SETUP program
6
Main CMOS Setup Menu
System Overview
IP25X2 BIOS VER:1.00
AMIBIOS
Version :08.00.15
Built Date:06/20/11
ID:LIPVB8106
System summary
IDE Device
CF Disk Device
SATA1 Device
SATA2 Device
System time (hh:mm:ss)
System date (mm:dd:yy)
Language
System Overview
IP25X2 BIOS VER:1.00
AMIBIOS
Version :08.00.15
Item Help
2011-06-20
Not detected
Not detected
Hard Disk
Not Detected
While entering setup
BIOS auto detects the
Presence of SATA
Device. This displays
The status of auto
detection of SATA
devices.
12 : 34 : 56
Fri 10/26/2012
English
2011-01-05
F1 Help ↑↓ Select Item +/- Change Values
F9 Setup Defaults
Esc Exit ←→ Select Menu Enter Select Sub Menu F10 Save and Exit
Advanced Settings Menu
Advanced Settings
Item Help
WARNING: setting wrong values in the below
sections may cause system to malfunction
Configure CPU
CPU Configuration
Supper IO Configuration
Hardware Health Configure
ACPI Configure
USB Configuration
APM Configuration
F1 Help ↑↓ Select Item +/- Change Values
F9 Setup Defaults
Esc Exit ←→ Select Menu Enter Select Sub Menu F10 Save and Exit
7
Exit Menu
Exit options
Item Help
Save Change and Exit
Discard Change and Exit
Discard Change
Exit system setup
after saving the
changes.
Load Optimal Default
F1
Help
Esc Exit
↑↓ Select Item
+/-
Change Values
←→ Select Menu Enter Select Sub Menu
F9 Setup Defaults
F10 Save and Exit
3.2 Touch screen driver installation:
Step 1: Navigate to the installer directory to find the setup.exe file. Double-click
on “setup.exe” to start installation.
8
Step 2: When installation starts, click [Next] to proceed to the next step.
Step 3: Installation in progress
9
Step 4: Uncheck “Install PS/2 interface driver” and click [Next] to continue
installation.
Step 5: Uncheck “install RS232 interface driver” and click [Next] to continue
installation.
10
Step 6: Select option “NONE”, click [Next] to continue installation.
Step 7: When installing USB touch, please connect the USB controller and USB
cable
11
Step 8: If there are additional touch monitors connected, please check “Support
multi- monitor system”.
Step 9: Select the destination location to install the touch driver. The default
path is “C: \ Program Files \ eGalaxtouch”. Click [Next] to continue installation.
12
Step 10: Select the Program Folder to install the utility.
“eGalaxtouch”. Click [Next] to continue installation.
Step 11: Check the option to create a desktop shortcut icon.
13
The default is
After install the driver successfully, identify the USB controller is installed as
shown below.
Touch function settings
14
Touch calibration
Touch device line test
15
4 Troubleshooting
1)
Terminal does not boot
If the terminal cannot boot after repeated pressing of the power switch when
connect to the power, the terminal power light remains off, the fan does not
operate, and the BIOS beeping is not heard, it might be power supply problems.
(a) Check the power adapter is plugged in correctly to the power outlet.
(b) Check the connection between the terminal and the power adapter, and then
re-boot the machine.
(c) If the terminal is working in high temperature environment that causes the
terminal automatically shut down in protection mode, please disconnect the
power of the machine. Wait until environment temperature has dropped and
restart.
(d) If the terminal does not boot after a sudden power failure or illegal shutdown,
unplug the adapter from the terminal, and press the power button several times.
Then plug in the adapter and boot again.
(e) If the adapter light blinks or go off, unplug the adapter immediately and do
not plugged in again.
Contact with our products service center.
2) The terminal automatically restart (or shutdown)
If terminal is frequently automatic shutdown or auto-boot during operation (or
boot up),
(a) Check the power supply is connected properly; make sure the plug is not loose
and contacts are in good condition;
(b) Check if the AC line voltage is stable;
(c) A sudden power failure or improper shutdown may cause this problem. Press
F8 to boot system into safe mode and debug.
(d) If any new hardware is added or replaced that caused this problem, remove
16
the hardware and reboot;
(e) If the above steps do not resolve this problem, reinstall the operating system.
3) The touch screen does not respond
(a) Remove the touch driver and then install it again.
(b) Execute the “eGalaxTouch utility and check if the interface port is working.
4) When touching the screen, cursor always returns to a fixed position.
(a) Check if there is anything pressing on the touch screen.
(b) Other high power or high frequency equipment may affect the screen or
controller.
Make sure that the touch screen is away from the high-voltage
equipment.
(c) The touch screen driver is not installed correctly, install the driver (please refer
to the "Touch Screen Setup") and run a 25-point calibration.
5) Touch screen is not accurate
Please run the touch screen calibration program with a 25-point recalibration, we
also recommend you to do this after change the monitor resolution or refresh
rate. When running the calibration, touch the center of calibration point to
assure accuracy.
6) The cursor moves opposite to the touch movement
(a) Run the 4/9/25 point calibration.
(b) The touch screen driver is not installed properly, reinstall the driver.
7) The cursor fixed at the edge of LCD
(a) Check if the edge of the screen is being pressed by something.
(b) Check the edges of the LCD if there is anything jammed in the front bezel.
(c) Make sure the touch screen is clean.
17
8) The cursor in the touch screen can only move in a small area or touch
positions are inaccurate.
(a) This situation usually occurs first time after installing the driver. Please run
the touch screen calibration program. We also recommend you to do this after
changing monitor resolution.
(b) Run the touch screen calibration program to do a 25-point recalibration.
18
5 Specifications
MODEL
SB9011D 15” All-in-one Touch POS Terminal
Main Board
CPU
Intel Atom Processor, D525 dual core 1.8GHz
Chipset
D525 + CH8M chipset
Memory
DDR3 1066/1333, up to 4GB
Storage
SATA 2.5 inch Hard Disk Drive, 160GB or higher
Display
LCD panel
15” TFT LCD
Resolution
1024x768
Brightness
250cd/m2
Touch Screen
5-wire resistive touch
View Angle
Horizontal: 140° Vertical: 130°
Tilting Angle
0 to 90°
I/O Ports
External DC Input
1x DC jack
PS/2 Ports
1x PS/2 mouse, 1x PS/2 keyboard
Serial Ports
5x DB9 serial ports (COM1, COM3-COM6)
Parallel Port
1x DB25 parallel port
VGA
1x DB15 2nd video VGA connector
LAN
2x RJ45, (1x 100Mbit, 1x 1Gbit)
USB
4x USB 2.0
Audio
1x audio out, 1x mic in
Environment
Operating Temperature
0°C to 40°C
Storage Temperature
-20°C to 60°C
Relative Humidity
8% to 80% non-condensing
Electrical (External Power Adapter)
Input
100 to 250VAC, 50 to 60Hz AC 2.5A
Output
DC 12V 7A
Power Consumption
35W max
Mechanical
Packing Dimensions
460x420x240mm
Weight
NW 6.5Kg, GW 8.5Kg
19
SB9011D All-in-one Touch POS terminal
20
Download PDF