Epson TW1000 - LCD Projector - HD 1080p User`s guide
PowerLite Home Cinema 1080.book Page 1 Tuesday, February 5, 2008 4:46 PM
PowerLite
®
Home Cinema 1080
Home Theater Projector
User’s Guide
2
PowerLite Home Cinema 1080.book Page 2 Tuesday, February 5, 2008 4:46 PM
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
Trademarks
Epson is a registered trademark, and Epson Exceed Your Vision, Crystal Fine, and 1080Perfect are trademarks of
Seiko Epson Corporation.
PowerLite and PrivateLine are registered trademarks, AccuCinema is a trademark, and Extra Care and Epson
Connection are service marks of Epson America, Inc.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing, LLC.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
The contents of this manual are subject to change without notice.
© 2007 Epson America, Inc.
12/07
CPD-23384R1
PowerLite Home Cinema 1080.book Page 3 Tuesday, February 5, 2008 4:46 PM
Contents
Introduction
Setting Up the Projector
Connecting Video and Computer Equipment
Installing Batteries in the Remote Control
Turning the Projector On and Off
Making Basic Adjustments
Contents
3
PowerLite Home Cinema 1080.book Page 4 Tuesday, February 5, 2008 4:46 PM
Adjusting Color Temperature, Skin Tone, and Gamma
Making Detailed Adjustments
Changing How the Menus Display
Sharpness and Picture Quality Settings
Adjustments for Computer Images
Selecting Memory Settings and Resetting the Projector
Deleting Saved Memory Settings
Customizing Projector Features
Maintenance
Cleaning and Replacing the Air Filter
Resetting the Lamp Usage Timer
4
Contents
PowerLite Home Cinema 1080.book Page 5 Tuesday, February 5, 2008 4:46 PM
Problem Solving
What To Do When the Lights Come On or Flash
Solving Remote Control Problems
Specifications
Notices
Epson America, Inc. Limited Warranty
Index
Contents
5
PowerLite Home Cinema 1080.book Page 6 Tuesday, February 5, 2008 4:46 PM
6
Contents
PowerLite Home Cinema 1080.book Page 7 Tuesday, February 5, 2008 4:46 PM
Introduction
■
■
■
■
■
The PowerLite ® Home Cinema 1080 projector lets you enjoy theater-quality images in the relaxing environment of your own home. Designed especially for home cinema use, it offers these outstanding features:
■
Native 1080p (1920 × 1080) resolution, 12000:1 dynamic contrast ratio, and up to
1200 lumens for incredibly rich, sharp images in any room lighting
■
Auto Iris system that constantly controls the lamp intensity based on the gamma and black/white levels of your projected content, for perfectly adjusted images and Deepest
Blacks
™
■
Epson ® Crystal Fine ™ 3LCD technology for reliable picture quality, increased contrast ratio and uniform colors
1080Perfect ™ video processing for more film-like images free of noise or artifacts
10-bit color quality for unmatched color accuracy, with over a billion colors available
Epson AccuCinema ™ color management delivered by the built-in optical Cinema Filter blocks out excess light for an expanded, purer color range and sophisticated grayscale tracking
■
HDMI
™
(High Definition Multimedia Interface digital video
™
) port for superior, uncompressed
True 16:9 wide-format projection
Flexible setup configurations, including front projection and ceiling mounted, with vertical and horizontal offset lens shift
■
Six color modes to quickly optimize viewing for different lighting environments and a vast array of custom color adjustments
Introduction
7
PowerLite Home Cinema 1080.book Page 8 Tuesday, February 5, 2008 4:46 PM
Projector Parts
Front
Control panel
Horizontal lens shift dial
Vertical lens shift dial
Zoom ring
Focus ring
Ventilation slots
Adjustable foot
Infrared receiver
Lens cover
Back
D/SCART port
(used mainly in
Japan)
Component video ports
Trigger out port
Video port
PC port
HDMI port
Infrared receiver
S-Video port AC power inlet Main power switch Control (RS-232C) port
Kensington ® lock port
8
Introduction
PowerLite Home Cinema 1080.book Page 9 Tuesday, February 5, 2008 4:46 PM
Bottom
Mounting bracket connections
Lamp cover Air filter
Projector Control Panel
Source button
Switches the video input source
Menu button
Displays the menus
Power light
Power button
Menu navigation buttons
Esc button
Exits the current menu item
Aspect button
Changes the picture’s aspect ratio
Warning light
Select button
Selects menu items or opens the line menu
Introduction
9
PowerLite Home Cinema 1080.book Page 10 Tuesday, February 5, 2008 4:46 PM
Remote Control Button Map
Operation light
Lights when you send remote control commands
On and Off buttons
Memory button
Recalls custom picture settings
Menu button
Displays the projector’s menus
Menu navigation buttons
Component button
Gamma button
Adjusts the gamma values of the screen display
ColorTemp. button
Changes the color temperature of the screen display
Pattern button
Displays test patterns to adjust the image
Illumination button
Lights the remote control buttons for easy viewing
Color Mode button
Optimizes viewing for different lighting environments
Aspect button
Changes the picture’s aspect ratio
Select/Line menu
Selects menu items or opens the line menu
ESC button
Exits the current menu item
Source buttons
Switch between equipment connected to the projector
Contrast button
Changes the contrast of the screen display
S. Tone button
Adjusts the skin tones of people appearing in the screen display
Blank button
Turns off the screen image
10
Introduction
PowerLite Home Cinema 1080.book Page 11 Tuesday, February 5, 2008 4:46 PM
Optional Accessories
Epson provides the following optional accessories for the projector:
Product
Replacement lamp
Air filter replacement
Projector mount
Kensington security lock (anti-theft device)
Part number
V13H010L39 (ELPLP39)
V13H134A09 (ELPAF09)
ELPHB550
ELPSL01
You can purchase accessories from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit
www.epsonstore.com
(U.S. sales) or
www.epson.ca
(Canadian sales).
Registration and Warranty
The PowerLite Home Cinema 1080 comes with a basic two-year carry-in warranty. For
In addition, for customers who register their projector, Epson offers free Extra Care
SM
Home
Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or
Canada, usually via overnight delivery. See your
Extra Care Home Service
brochure for details.
To register, simply fill out the registration card that came with your projector and mail it to
Epson. Or you can register online at
www.epson.com/webreg
. Registering also lets you receive special updates on new accessories, products, and service.
Introduction
11
PowerLite Home Cinema 1080.book Page 12 Tuesday, February 5, 2008 4:46 PM
Using This Manual
This book contains all the information you need to use the projector, in addition to basic setup and maintenance instructions, troubleshooting tips, important safety instructions, specifications, and warranty information.
Please follow these guidelines as you read through the manual:
Warning:
Must be followed carefully to avoid bodily injury.
Caution:
Must be observed to avoid damage to your equipment.
Note:
Contains important information about your projector.
Tip:
Contains helpful projection tips .
Need additional help? Take advantage of Epson’s automated support services 24 hours a day at
epson.com/support
. Use this site to view FAQs (Frequently Asked Questions) or product information and e-mail your questions to Epson support.
If you need more help, you can use the Epson PrivateLine ® Support service. Call
(800) 637-7661 and enter the PIN on the PrivateLine support card that came with your projector.
12
Introduction
PowerLite Home Cinema 1080.book Page 13 Tuesday, February 5, 2008 4:46 PM
Setting Up the Projector
Follow the instructions in this section to choose a location for the projector, connect the cables, and display an image.
Choosing a Location
You can install the projector for various viewing setups, as shown below.
Center Side
Ceiling
Setting Up the Projector
13
PowerLite Home Cinema 1080.book Page 14 Tuesday, February 5, 2008 4:46 PM
Ideally, place the projector at a height where its lens is between the top and bottom of the screen. That way, you can keep the projector level and use the vertical lens shift dial to position the image. This produces the best-looking picture.
Try to be as close as possible to the calculated projector position when installing the projector.
Too much lens shift can cause minor reduction in image dimensions. The image display position cannot be moved to the maximum distance in both the vertical and horizontal directions. For example, the image cannot be shifted vertically when it has been shifted horizontally by the full amount. When the image has been shifted vertically by the full amount, it can be shifted up to 9 percent of the horizontal width of the screen.
If you place the projector off to the side, aim it straight ahead (rather than at the center of the screen), then use the horizontal lens shift dial to center the image on the screen.
Horizontal lens shift dial Vertical lens shift dial
Caution:
Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the lens position.
14
Setting Up the Projector
PowerLite Home Cinema 1080.book Page 15 Tuesday, February 5, 2008 4:46 PM
The maximum size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings and how you use the Zoom ring, the actual size may be smaller. Use this table as a rough guide for projector placement:
16:9 aspect ratio
Projection distance
Maximum diagonal image size (width × height)
2.8 to 6.2 feet
3.8 to 8.3 feet
5.8 to 12.5 feet
7.8 to 16.7 feet
30 in. (26 × 15 in.)
40 in. (35 × 20 in.)
60 in. (51 × 28 in.)
80 in. (71 × 39 in.)
9.8 to 20.9 feet
11.8 to 25.1 feet
14.7 to 31.4 feet
100 in. (87 × 47 in.)
120 in. (106 × 59 in.)
150 in. (130 × 75 in.)
Offset A to Offset B
6.8 to –6.8 in.
9.1 to –9.1 in.
13.6 to –13.6 in.
18.2 to –18.2 in.
22.7 to –22.7 in.
27.2 to –27.2 in.
34 to –34 in.
Horizontal
Offset
0 to 13 in.
0 to 17 in.
0 to 26 in.
0 to 35 in.
0 to 44 in.
0 to 52 in.
0 to 65 in.
4:3 aspect ratio
Projection distance
Maximum diagonal image size (width × height)
3.5 to 7.6 feet 30 in. (24 × 18 in.)
4.7 to 10.1 feet
7.1 to 15.3 feet
40 in. (32 × 24 in.)
60 in. (47 × 35 in.)
Offset A to Offset B
8.3 to –8.3 in.
11.1 to –11.1 in.
16.7 to –16.7 in.
Horizontal
Offset
0 to 16 in.
0 to 21 in.
0 to 32 in.
9.6 to 20.4 feet
12 to 25.5 feet
14.4 to 30.7 feet
18 to 38.4 feet
80 in. (63 × 47 in.)
100 in. (79 × 59 in.)
120 in. (94 × 71 in.)
150 in. (118 × 91 in.)
22.2 to –22.2 in.
27.8 to –27.8 in.
33.3 to –33.3 in.
41.7 to –41.7 in.
0 to 43 in.
0 to 53 in.
0 to 64 in.
0 to 80 in.
To determine the exact image size when you know the projection distance (or the exact projection distance when you know the desired image size), you can use the Projection
Distance Calculator. You can download this program from the Epson website at
epson.com/support
.
Setting Up the Projector
15
PowerLite Home Cinema 1080.book Page 16 Tuesday, February 5, 2008 4:46 PM
Also keep these considerations in mind:
■
Make sure there is plenty of space for ventilation around and under the projector. Do not set the projector on top of loose materials that could block the vents underneath.
■
Make sure the projector is within 9.8 feet of a grounded electrical outlet or extension cord.
Installing the Projector
To install the projector, you first need to determine the location, based on the size of your screen (maximum diagonal image size). Use the table on page 15 as a guide to positioning the projector. Note the following dimensions:
■
Distance from the center of the lens to the mounting bracket holes: 2.60 inches (66 mm),
0.35 inch (8.8 mm) maximum vertical lens shift
■
Distance from the center of the lens to the center of the projector: 4.33 inches (110 mm),
0.30 inch (7.7 mm) maximum horizontal lens shift
16
Setting Up the Projector
PowerLite Home Cinema 1080.book Page 17 Tuesday, February 5, 2008 4:46 PM
The following illustrations show the dimensions of the projector:
5.18 in.
2.60 in.
15.98 in.
4.33 in.
11.81 in.
2.08 in.
4.88 in.
5.63 in.
0.75 in.
3.04 in.
12.20 in.
6.30 in.
To install, you will need the optional projector mount designed for the projector. See page 11
for ordering information.
Warning:
When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use any type of oil or lubricant. These may cause the projector casing to crack and the projector may fall, causing serious injury and serious damage to the projector.
Follow the instructions included with the mount to install the projector, which weighs
12.3 pounds. The wall or ceiling where you install it must be capable of supporting a weight of 85.6 pounds.
Setting Up the Projector
17
PowerLite Home Cinema 1080.book Page 18 Tuesday, February 5, 2008 4:46 PM
In addition to the tools supplied with the projector mount, you will need a Phillips head screwdriver and a drill to use on the wall or ceiling.
If you install the projector on the ceiling, you will need to invert the picture so that it appears right side up. Follow these steps:
1. Press the
Menu
button on the remote control.
Menu button
2. Press the menu navigation buttons to open the
Settings
menu, then select
Projection
.
3. Use the navigation buttons to select
Front/Ceiling
.
4. Press the
Menu button when done.
If you are planning to use an AV controller with the projector,
refer to the table of ESC/VP21 command codes on page 65.
Menu navigation buttons
Connecting the Cables
Connecting Video and Computer Equipment
You can connect the projector to any type of video equipment, such as a VCR, DVD player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera. You can also connect it to a desktop or laptop PC or Apple
®
Macintosh
®
system.
18
Setting Up the Projector
PowerLite Home Cinema 1080.book Page 19 Tuesday, February 5, 2008 4:46 PM
You can connect up to five pieces of video equipment at the same time, using any of the commercially available cables shown below:
Port name
HDMI
Video equipment connection*
Use an HDMI cable:
Computer connection*
Component Use a component video cable
(with RCA-style connectors):
—
PC
Component video ports
Connect the cable to the three component video ports. Match corresponding colors between the cable and the ports.
— Use a Mini D-sub, 15-pin monitor cable to connect to a computer RGB
(monitor) port:
RGB port
S-Video Use an S-video cable: —
Video Use an RCA video cable: —
* For details on compatible video formats, see page 63.
Setting Up the Projector
19
PowerLite Home Cinema 1080.book Page 20 Tuesday, February 5, 2008 4:46 PM
For best results, connect your video equipment to the HDMI (High-Definition Multimedia
Interface) port, if possible. If your equipment doesn’t support HDMI, connect it to one of the following ports (highest quality listed first): Component (for component video), S-Video, or
Video (for composite video).
Connect video equipment to one of these ports
Connect a computer to one of these ports
If you connect to the Component port, be sure to select the correct Input Signal setting for
your equipment, or the image may not display properly (see page 23).
Making Other Connections
Connect the power cable and other cables described below, depending on how you plan to use the projector.
■
Plug the power cable into the projector and a grounded electrical outlet.
20
Setting Up the Projector
PowerLite Home Cinema 1080.book Page 21 Tuesday, February 5, 2008 4:46 PM
■
The Trigger out port outputs a 12-volt DC signal when the projector is turned on. This lets a central control system monitor whether the projector is on or off, and can be used to raise or lower your projection screen automatically when the projector is in use.
Connect a 3.5-mm mini jack to the port, as shown.
Installing Batteries in the Remote Control
The remote control uses two AA batteries.
Warning:
Keep batteries away from children. If a battery is swallowed, contact your doctor immediately.
1. Release the tab and lift open the cover.
2. Insert two new AA batteries as shown.
3. Insert the tab on the cover and press it down until it clicks into place.
Aim the remote control at the front or back of the projector. Make sure you are within 30 feet of the projector with the remote aimed within a 30° angle from the infrared receivers.
If you suspect the batteries are weak, take the remote control to a dark room and press the illumination button. If the buttons do not glow red, replace the batteries.
Setting Up the Projector
21
PowerLite Home Cinema 1080.book Page 22 Tuesday, February 5, 2008 4:46 PM
Turning the Projector On and Off
Turning On the Projector
1. Remove the lens cap.
2. Turn on any connected equipment you plan to use.
3. Turn on the main power switch on the back of the projector.
Power switch
4. Press the
On
button on the remote control or the
P Power
button on the projector.
Turn on the projector
Note:
To prevent children from turning on the projector, you can use the Child Lock. See page 32
for details.
If you’ll be using the projector at an altitude above 4900 feet (1500 meters), turn on High Altitude
Mode so the fan can properly cool the projector at the high altitude air pressure. See page 45 for
details.
The projector takes about 30 seconds to warm up and display an image. If you don’t see a
picture, you may need to change the image source as described on page 23.
22
Setting Up the Projector
PowerLite Home Cinema 1080.book Page 23 Tuesday, February 5, 2008 4:46 PM
Turning Off the Projector
1. Turn off any equipment connected to the projector.
2. Press the
Off
button on the remote control, or press the
P
Power
button on the projector twice.
3. When the
P
Power
light stops flashing orange and stays on, turn off the projector’s main power switch on the back.
It is now safe to unplug the projector, if necessary.
Caution:
Turn off this product when not in use to prolong the life of the projector. Continuous
24-hour-a-day use may reduce the overall life of the product. Never turn off the main power switch without first turning off the lamp and letting it cool as described above, or you could damage it and reduce lamp life.
Selecting the Image Source
The Source buttons on the projector and remote control let you switch between images from different pieces of equipment connected to the projector (such as a DVD player, cable or satellite box, or video game console).
Press the
Source
button on the remote control that corresponds to the port to which your video source is connected.
Source buttons
Setting Up the Projector
23
PowerLite Home Cinema 1080.book Page 24 Tuesday, February 5, 2008 4:46 PM
If you press the
Source
button on the projector, you see a menu of available sources.
Source button
Press the u
or d
button to go up or down the menu, then press the
Select
button.
Note:
If an image does not appear, see “Problem Solving” on page 55.
To temporarily turn off the image and darken the screen, press the Blank button on the remote control. Press the Blank button again to return to normal viewing.
24
Setting Up the Projector
PowerLite Home Cinema 1080.book Page 25 Tuesday, February 5, 2008 4:46 PM
Positioning the Image
If the image is not centered on the screen, use the horizontal and vertical lens shift dials to adjust its position.
Caution:
Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the lens position.
Horizontal lens shift dial
Vertical lens shift dial
Note:
You can display a test pattern to help adjust the image position by pressing the Pattern button on the remote control. Press the Pattern button again to turn off the test pattern.
When you hear a click, the lens position is almost centered. If the lens shift dial becomes hard to turn, you cannot adjust the position any further.
If one side of the image is taller than the other, make sure the projector is parallel to the screen. If necessary, adjust the front feet so that the projector is horizontal.
Adjustable feet
Setting Up the Projector
25
PowerLite Home Cinema 1080.book Page 26 Tuesday, February 5, 2008 4:46 PM
The image display position cannot be moved to the maximum distance in both the vertical and horizontal directions. For example, the image cannot be shifted vertically when it has been shifted horizontally by the full amount. When the image has been shifted vertically by the full amount, it can be shifted up to 9 percent of the horizontal width of the screen.
26
Setting Up the Projector
PowerLite Home Cinema 1080.book Page 27 Tuesday, February 5, 2008 4:46 PM
Making Basic Adjustments
Follow the instructions in this chapter to make basic adjustments to the image shape, size,
color, and quality. For further refinements, see “Making Detailed Adjustments” on page 33.
Focusing and Zooming
Sharpen or reduce the focus using the focus ring.
Zoom into or out of the picture using the zoom ring.
Wide Zoom ring
Focus ring
Tele
Making Basic Adjustments
27
PowerLite Home Cinema 1080.book Page 28 Tuesday, February 5, 2008 4:46 PM
Choosing the Aspect Ratio
In many cases, video signals are automatically resized to fit on your screen when
Auto
is selected as the Aspect setting.
You may need to change the size of the image (or aspect ratio) for certain image types by pressing the
Aspect
button on the remote control.
If your video source is connected to the HDMI, S-Video, or
Video port—or the Component port when it is outputting
480i or 480p signals—select
Auto
to automatically display your image in the correct size.
Aspect button
If the
Auto
setting is unavailable, you may want to choose one of these settings:
■
Normal
for standard TV broadcasts, computer images, or images with a 4:3 aspect ratio.
■
Full
for images recorded in squeeze mode.
■
Zoom
for images recorded in 16:9 (wide-screen) format.
4:3 image using Normal setting 16:9 image using Zoom setting
■
Wide for expanding a 4:3 image to 16:9 so it fills the whole screen. This stretches only the right and left sides of the image; the central part is unchanged.
Note:
If you display a 4:3 image using the Zoom setting, the top and bottom will be cut off. You can use the Zoom Caption Pos. option and other settings to resize and reposition the image. For
For details on how the projector resizes the picture when you choose an Aspect setting, see
28
Making Basic Adjustments
PowerLite Home Cinema 1080.book Page 29 Tuesday, February 5, 2008 4:46 PM
Choosing the Color Mode
You can change the Color Mode to automatically adjust brightness, contrast, and color, letting you quickly optimize the projected image for various lighting environments. You can also select a different color mode for each input source—which is useful if you view different types of images from different sources. (For example, you might set the source to
Living
Room if it’s usually used for watching movies in the daytime with the blinds closed, or you might set the source to
Dynamic
for playing video games with the blinds open.)
Select the image source you want to adjust, then press the
Color Mode
button on the remote control. Choose from these settings:
■
Dynamic for projecting the brightest picture available.
■
Living Room for watching movies during the day.
■
Natural
for projecting the most natural, accurate colors.
Color
Mode button
■
Theatre for viewing movies in a dark room.
■
Theatre Black 1 for images that are close to those in professional-use broadcast monitors.
■
Theatre Black 2 for black and white movies or those with dark scenes.
When you select the
Natural or
Theatre
setting, the built-in Epson Cinema Filter automatically increases the contrast and naturalizes projected skin tones.
Making Basic Adjustments
29
PowerLite Home Cinema 1080.book Page 30 Tuesday, February 5, 2008 4:46 PM
Adjusting Color Temperature, Skin Tone, and
Gamma
To further customize the color and image quality, you can adjust the Gamma, abstract Color
Temperature, and Skin Tone settings using buttons on the remote control. (Not available when you’re projecting sRGB images.)
Gamma button
S. Tone button
ColorTemp. button
Note:
You can fine-tune these and other color and image quality settings using the projector’s
menu system (see page 33). You can also save combinations of picture settings with the Memory
feature for easy recall (see page 41).
Select the image source you want to adjust, then press any of the buttons described below. A slider appears beneath the image so you can adjust the setting and view the effect of your adjustments.
■
ColorTemp.
adjusts the overall color tint (absolute color temperature) between 5000K and 10000K. Higher temperature settings increase the blue tint and lower temperature settings increase the red tint.
■
S. Tone
adjusts the color of projected skin tones. The Epson Cinema Filter automatically optimizes this setting, but you can customize it if necessary. Higher numbered settings increase the green tones and lower numbered settings increase the red tones.
30
Making Basic Adjustments
PowerLite Home Cinema 1080.book Page 31 Tuesday, February 5, 2008 4:46 PM
Adjusting the Gamma Setting
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to blur the bright areas. Higher values will darken the light areas. Gamma presets make minor adjustments to mid-tone values. The larger the gamma preset, the lower the midtone values.
Changing these settings affects contrast which can be seen as a blur in bright areas.
1. Press the
Gamma
button. You see the following displayed on the screen:
2. Do one of the following:
■
Select one of the numeric correction values using the u or d
button on the remote or control panel and press the
Select
button
.
You see the setting reflected in the graph on the right. The horizontal axis represents the input signal level, and the vertical axis represents the output signal level. Press the
Gamma
button to exit.
■
Select
Customized
. Then continue with the next step.
3. Do one of the following:
■
Select
Adjust it from the image
. You see a gamma icon on the projected image. Use the arrow buttons to move the icon to the area of brightness you want to adjust, then press
Select.
The custom gamma graph appears with the channel selected for adjustment. Press the u or d
button to adjust and then press
Select.
■
Select
Adjust it from the graph
. When the gamma graph appears, use the l
or button to select the point on the graph that you want to adjust, and then use the r u or d
button to adjust the settings. Press
Select to save your setting and exit.
Making Basic Adjustments
31
PowerLite Home Cinema 1080.book Page 32 Tuesday, February 5, 2008 4:46 PM
Locking the Projector
The projector includes two lock settings to prevent the image from being accidentally changed once it’s adjusted, and to keep children from turning on the projector without adult supervision.
To access the lock settings, follow these steps:
1. Press the
Menu
button on the remote control.
2. Use the menu navigation buttons to open the
Settings menu.
Menu button
3. Choose from these options:
■
Child Lock
to disable the
P Power
button on the projector’s control panel unless it is pressed for about 3 seconds. (You can use the
P Power button to turn it off, however.) Since you can still use the remote control to turn on the projector, you may want to keep it away from children’s reach.
Menu navigation buttons
■
Operation Lock
to disable all the buttons on the projector’s control panel. A lock icon appears on the screen whenever you press a button with Operation Lock turned on. To operate the projector, you must use the remote control. To cancel Operation
Lock, press and hold the
Select
button on the projector’s control panel for at least
7 seconds.
4. Press
Menu
to exit the menu system.
If you turned on the Operation Lock, the projector buttons are now locked.
If you turned on the Child Lock, turn off the projector and let it cool down. The Child
Lock takes effect after the cool-down period.
32
Making Basic Adjustments
PowerLite Home Cinema 1080.book Page 33 Tuesday, February 5, 2008 4:46 PM
Making Detailed Adjustments
You can use the projector’s on-screen menus to make detailed adjustments to the image quality—such as the brightness, contrast, sharpness, and color. You can also change the menu display, sleep mode settings, and other projector features.
Using the Menu System
You can access the menu system either from the remote control or the buttons on the projector’s control panel. You can access the full menu or a line menu that lets you adjust the
Picture and Memory settings while viewing their effects on your display. You can also change
the menu language and control how the menus display (see page 35).
1. To display the full menu, press the
Menu
button on the projector or remote control. You see a display like this one (the actual display depends on the connected equipment):
Main menu options
Settings available for the highlighted menu
Note:
Depending on which equipment is connected to the projector, some options may not be available.
2. Press the u
or d
button to highlight a main menu option (
Image
,
Signal
,
Settings
,
Memory
,
Info
or
Reset
), then press the
Select
button to select it.
3. Press the u
or d
button to highlight a setting, then press the
Select
button.
4. Press the u
, d
, l
, or r button to change settings as necessary. You may have to press the
Select
button to confirm your choice.
Making Detailed Adjustments
33
PowerLite Home Cinema 1080.book Page 34 Tuesday, February 5, 2008 4:46 PM
5. When you’re finished, press the
Esc
button to return to the previous menu or press the
Menu
button to exit the menu system.
To display one of the line menus of the Image menu, press the
Select
button. You see a display like this at the bottom of the image:
Press the u
or d
button to highlight an option (if necessary), then press the l
or r button to adjust it. Press the
Esc
button to return to the previous menu or the
Menu
button to exit the menu system. Press the
Memory
button to return to the setting stored in memory.
You can access the following settings through the line menu while viewing their effects on your display:
■
■
■
■
■
■
■
■
■
Brightness (see page 36)
Contrast (see page 36)
Color Saturation (see page 38)
Absolute Color Temperature (see page 30)
Brightness Control (see page 37)
34
Making Detailed Adjustments
PowerLite Home Cinema 1080.book Page 35 Tuesday, February 5, 2008 4:46 PM
Changing How the Menus Display
Use these options to control how the menus display.
■
Language
Settings > Language
Select from 20 languages to use in the menu system.
■
Menu Position
Settings > Display > Menu Position
Use the arrow buttons to choose a position on the screen for displaying the menu.
■
Menu Color
Settings > Display > Menu Color
Select a color scheme for displaying the menus.
Adjusting the Picture Quality
Before fine-tuning the image using these adjustments, make sure you have already selected the
best Color Mode for your picture and viewing environment, as described on page 29. Then
use the settings in this section to finish adjusting the picture to your liking.
Most image quality settings are saved independently for each input source (Video, S-Video,
HDMI, Component, PC) and color mode. After you finish adjusting the settings for one input source, switch to the other input sources you’ll be using and make any necessary adjustments.
Input Brightness Settings
If the signal from connected equipment is weak and images appear dark, you can adjust the
Brightness and Contrast settings. You can adjust brightness and contrast for each image source and color mode.
Adjust this setting first, then fine-tune the image with the remaining settings.
The Brightness setting controls how much light is produced by the projector, and the
Contrast setting adjusts the difference between the bright and dark areas of the projected image. The other settings listed on the following page control how the projector interprets the light and dark areas of the picture.
Making Detailed Adjustments
35
PowerLite Home Cinema 1080.book Page 36 Tuesday, February 5, 2008 4:46 PM
■
Brightness
Image > Brightness
Adjust the brightness so it’s suitable for your viewing conditions. For example, if you’re projecting in a brightly lit room or onto an especially large screen, you may need to increase the brightness. Decrease the brightness for dark rooms or small screens; this also reduces power consumption and fan noise, and helps to prolong the life of the lamp.
■
Contrast
Image > Contrast
This setting adjusts the difference between bright and dark areas.
■
Auto Iris
Image > Auto Iris
When this setting is on, the amount of light produced by the lamp is automatically adjusted according to the brightness of the image. The setting is stored separately for each image source and color mode.
■
Setup Level
Signal > Setup Level
This setting adjusts the threshold at which dark areas of the image are rendered black
(0 IRE). For compatibility with most DVD and video equipment sold in the United
States, leave this setting at 0%. Check your video equipment’s specifications to be sure of the correct setting.
■
EPSON Super White
Signal > EPSON Super White
Note:
This setting can be used only when the Color Mode is set to Natural, Theatre, Theatre
Black 1, or Theatre Black 2 (see page 29).
If bright parts of the image are washed out or overexposed (when the input signal contains values over 100 IRE), turn this setting on to compensate. When this setting is turned on, the projector disregards the HDMI Video Range setting.
■
HDMI Video Range
Signal > HDMI Video Range
Note:
This setting can be used only when HDMI is selected as the image source (see page 23).
If your video equipment has an HDMI port and you’ve connected it to the projector using an HDMI cable, set the level of the projector to match that of the video equipment.
When this setting is turned on, the projector disregards the EPSON Super White setting.
36
Making Detailed Adjustments
PowerLite Home Cinema 1080.book Page 37 Tuesday, February 5, 2008 4:46 PM
■
Brightness Control
Image > Brightness Control
This setting controls the light output from the projector. On high, the lamp uses 170 W of power. On low, the lamp uses 135 W.
Sharpness and Picture Quality Settings
If the image looks fuzzy, or if it contains noise or flickering, you can use these settings to correct it.
■
Sharpness
Image > Sharpness
Use this function to make lines and edges appear more distinct in the image. This setting is stored separately for each image source and color mode setting. You can select
Standard
to adjust the sharpness of the entire image, or select
Advanced
to access the following submenu:
Choose
Thin-Line Enhancement to sharpen details such as hair and clothing. Choose
Thick-Line Enhancement to sharpen large contours and backgrounds.
■
Progressive
Signal > Progressive
The projector uses 3D DigiScan HD Circuitry Processing for video-sourced images. For film-sourced images, the projector uses 3-2 pulldown detection and optimizes the image accordingly.
Leave this setting on
Video
for most purposes. Set to
Film/Auto
when the input source is a film, and you want to project an image closer to its original source.
Note:
This setting applies only when viewing composite video, S-video, component video, or
480i or 575i RGB video (see page 63).
Making Detailed Adjustments
37
PowerLite Home Cinema 1080.book Page 38 Tuesday, February 5, 2008 4:46 PM
■
Motion Detection
Signal > Motion Detection
This setting specifies how signals are converted to progressive signals. Select a lower setting for slow-moving or still images (
S
) or select a higher number for video images
(
M
).
Note:
This setting applies only when viewing composite video, S-video, component video, or
480i or 575i RGB video.
■
Noise Reduction
Signal > Noise Reduction
This setting reduces flickering of analog images. You can select from 3 levels of noise reduction.
Color Settings
If the image colors don’t look correct, you can adjust them using these settings. Use the first three settings described below to make the most visible changes. If you only need to make slight adjustments, you can fine-tune the picture with the remaining settings. Most color settings are stored separately for each image source and color mode.
■
Color Saturation
Image > Color Saturation
Adjusts the color intensity of the image.
■
Tint
Image > Tint
Shifts the color balance between magenta and green.
■
Abs. Color Temp.
Image > Abs. Color Temp.
Shifts the color balance between red and blue, making the image appear warmer or cooler. You can also access this setting by pressing the
ColorTemp.
button on the remote
control. See page 30 for more information.
38
Making Detailed Adjustments
PowerLite Home Cinema 1080.book Page 39 Tuesday, February 5, 2008 4:46 PM
■
Skin Tone
Image > Skin Tone
Makes fine adjustments to the tint and controls the amount of magenta or green in the image. Also useful for correcting black-and-white images, if they look tinted. You can access this setting by pressing the
S. Tone
button on the remote control. See page 30 for
more information.
■
RGB
Image > Advanced > RGB
Use the RGB settings to fine-tune the color of the image. You can adjust the offset and gain for each signal color (red, green, and blue). Use
Offset
to adjust darker shades and
Gain
for the lightest shades.
■
RGBCMY
Image > Advanced > RGBCMY
Use the RGBCMY settings to adjust the hue and saturation of the six color components
(red, green, blue, cyan, magenta, yellow). After adjusting each color, press
Esc
to move to another menu option.
■
Gamma
Image > Advanced > Gamma
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to blur the bright areas. Higher values will darken the light areas.
You can also access this setting by pressing the
Gamma button on the remote control.
See page 31 for more information.
Making Detailed Adjustments
39
PowerLite Home Cinema 1080.book Page 40 Tuesday, February 5, 2008 4:46 PM
Adjustments for Computer Images
In addition to the settings described above, you can adjust the Tracking and Sync settings for analog RGB computer images. Normally, these settings are adjusted automatically by the projector. If you notice that the image is blurry or contains dark vertical bands, you may need to adjust the settings yourself.
■
Auto Setup
Signal > Auto Setup
Leave this setting on so that the projector automatically adjusts the tracking, sync, and position of the image.
■
Tracking
Signal > Tracking
Adjust the tracking to eliminate vertical bands. It is easiest to adjust the tracking when the image contains a lot of fine detail
(such as black text on a white background).
■
Sync.
Signal > Sync.
Adjust the synchronization to eliminate blurriness. For best results, make sure the tracking is properly adjusted first.
40
Making Detailed Adjustments
PowerLite Home Cinema 1080.book Page 41 Tuesday, February 5, 2008 4:46 PM
Selecting Memory Settings and Resetting the
Projector
Your projector comes with 10 memory locations for installers to save customized settings, designed to provide the best color quality for each of your video inputs.
Selecting Memory Settings
You can easily recall the memory settings by using the memory button on the remote control.
1. Press the
Memory
button on the remote control.
2. Select
Load Memory
.
3. Use the arrow buttons to select the desired setting, then press the
Select button.
After a moment, the image appears on the screen using your selected setting.
Memory button
Creating Memory Settings
Memory settings store the Brightness and Contrast settings, Color Mode, and other color
settings described on pages 38 and 39.
1. Press the
Menu
button on the remote control.
2. Open the
Memory menu, then select
Save Memory
.
3. Select the memory name you want to use, then press the
Select
button to save your settings.
Note:
Saved settings are indicated by a green highlight next to the memory name. If you select a name that is already in use, the existing settings will be erased and new ones saved in their place.
Making Detailed Adjustments
41
PowerLite Home Cinema 1080.book Page 42 Tuesday, February 5, 2008 4:46 PM
Deleting Saved Memory Settings
You can clear all your memory settings at once.
1. Press the
Menu
button on the remote control.
2. Open the
Reset menu, then select
Reset Memory
.
3. Press the
Select button to delete the memory settings.
Note:
You can delete memory settings one at a time with the Erase Memory setting under the
Memory menu.
Resetting the Projector
If the image quality isn’t what you expect, one or more settings may be adjusted improperly.
If necessary, you can restore the projector to its factory-default (original) settings.
To restore the settings in a specific menu (such as the Image or Settings menu), open that menu, select
Reset
, and confirm as needed. The example below shows how to reset the
Image menu settings:
Open the Image menu . . .
. . . and select
Reset
You can also reset the lamp usage timer or restore all the projector settings to their original values. Follow these steps:
1. Press the
Menu
button on the remote control.
2. Open the
Reset
menu.
42
Making Detailed Adjustments
PowerLite Home Cinema 1080.book Page 43 Tuesday, February 5, 2008 4:46 PM
3. Do one of the following:
■
Select
Reset Lamp Hours to clear the lamp usage timer and reset it to zero.
You should reset the lamp timer only when you install a new projector lamp. See
■
■
Select
Select
Reset Memory
Reset All
to clear all memory settings.
to return all projector settings to their original defaults (except
Component, Save Memory, Language, and Lamp).
Customizing Projector Features
Use the settings in this section to adjust the image size and position, suppress on-screen text, and select basic setup options.
Image Sizing
Before adjusting any of these settings, make sure you have already selected an appropriate
aspect ratio for the type of picture you’re viewing (see page 28).
■
Output Scaling
Signal > Output Scaling
For component video formats, this setting lets you see the edges of the image that are not
normally visible in the picture (see page 63).
■
Position
Signal > Position
Use the arrow buttons to fine-tune the position of the image on the screen.
■
Zoom Caption Pos.
Signal > Zoom Caption Pos.
■
Lets you adjust the shape and position of the image so that subtitles are visible (available only if the aspect ratio has been set to Zoom). Use
Zoom Size
to adjust the proportions of the image, and
Zoom Caption Pos. to move the image up or down. You can adjust output scaling before zoom position.
Aspect
Signal > Aspect
This setting lets you change the aspect ratio of your image, and works the same as pressing the
Aspect
button on the remote control. See page 28 for more information.
Making Detailed Adjustments
43
PowerLite Home Cinema 1080.book Page 44 Tuesday, February 5, 2008 4:46 PM
Screen Options
■
Messages
Settings > Display > Messages
Turn this setting off if you want to prevent on-screen messages from appearing (such as the no-signal message, or the identifying text that appears when you switch between image sources or color modes).
■
Startup Screen
Settings > Display > Startup Screen
Turn this setting off if you want to prevent the startup screen from appearing while the projector is warming up.
■
Display Background
Settings > Display > Display Background
Changes the screen that’s used when the projector is not receiving a signal or when you press the
Blank
button to temporarily stop projection.
Other Setup Options
■
Projection
Settings > Projection
You can select different options for projecting the image:
Front
,
Front/Ceiling
,
Rear
,
Rear/Ceiling
.
■
Direct Power On
Settings > Direct Power On
Sets projection to start when the main power switch is turned on, without pressing the
On
button on the remote control or the
P Power
button on the projector.
Note:
When direct power on is enabled, power surges that occur after a power outage can cause the projector to turn on.
■
Video Signal
Settings > Input Signal > Video Signal
Leave this setting on
Auto
so the projector can automatically interpret the format, such as
NTSC or PAL (for standard TV formats).
44
Making Detailed Adjustments
PowerLite Home Cinema 1080.book Page 45 Tuesday, February 5, 2008 4:46 PM
■
Component
Settings > Input Signal > Component
Change this setting to match the type of equipment connected to the Component port.
For component video, select
Auto
to let the projector automatically interpret the signal; or select
YCbCr
or
YPbPr
to manually select your video equipment’s signal.
■
Trigger Out
Settings > Trigger Out
Turn on this setting if you want the
Trigger out
port to output a 12-volt signal while the projector is operating. You can use this to raise or lower your projection screen.
■
Sleep Mode
Settings > Sleep Mode
Turn off this setting if you don’t want the projector to enter sleep mode. (Sleep mode shuts the projector off automatically when there is no video signal.)
Select
5 min.
,
10 min.
, or
30 min. as the length of time before shutoff; decreasing the time conserves power and extends the life of the lamp.
To turn the projector back on, press the
On
button on the remote control, or press the
P
Power
button on the projector.
■
Child Lock
Settings > Child Lock
Lets you lock the
P Power
button on the projector’s control panel to make it more
difficult for a child to turn on the projector. See page 32 for more information.
■
Operation Lock
Settings > Operation Lock
Lets you disable all the buttons on the projector’s control panel to prevent the image from
being accidentally changed once it is adjusted. See page 32 for more information.
■
High Altitude Mode
Settings > High Altitude Mode
Adjusts the speed of the fan so it can properly cool the projector at altitudes above
4900 feet (1500 meters).
Making Detailed Adjustments
45
PowerLite Home Cinema 1080.book Page 46 Tuesday, February 5, 2008 4:46 PM
46
Making Detailed Adjustments
PowerLite Home Cinema 1080.book Page 47 Tuesday, February 5, 2008 4:46 PM
Maintenance
Your projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. You also may need to clean the air filter to prevent overheating.
Warning:
Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this
User’s Guide
.
The only parts you should replace are the air filter and the lamp. If another part needs replacing, contact your dealer or a qualified servicer.
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
■
■
Use a canister of compressed air to remove dust.
To remove dirt or smears, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface.
Caution:
Never rub the lens with abrasive materials.
Maintenance
47
PowerLite Home Cinema 1080.book Page 48 Tuesday, February 5, 2008 4:46 PM
Cleaning the Projector Case
Before you clean the case, turn off the projector and unplug the power cord.
■
To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.
■
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. Then wipe the case and dry it with a dry cloth.
Caution:
Never use wax, alcohol, benzene, thinner, or other chemical detergents. These can damage the case.
Cleaning and Replacing the Air Filter
Your projector includes an air filter to ensure the best performance. If dust collects on the air filter on the bottom of the projector, clean it as described below. Dust clogs prevent proper ventilation and cause overheating and damage to the projector.
1. Press the
P
Power
button and wait for the
P
Power
light to stop flashing. The projector cools down.
2. Turn off the projector using the power switch on the back.
3. Unplug the power cord and disconnect any cables.
4. Use a small vacuum cleaner that is designed for computers and other office equipment to clean the filter on the bottom of the projector, as shown. If you don’t have one, gently clean the filter using a very soft brush (such as a clean artist’s paintbrush).
If the dirt is difficult to remove or the filter is broken, replace it. You can purchase air filter part number
V13H134A09 from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON
(800-463-7766). To purchase online, visit
www.epsonstore.com
(U.S. sales) or
www.epson.ca
(Canadian sales).
48
Maintenance
PowerLite Home Cinema 1080.book Page 49 Tuesday, February 5, 2008 4:46 PM
5. If you need to replace the filter, release the tab and lift up the cover.
6. Remove the old filter and replace it with a new one.
7. To replace the cover, insert the tabs and press down until the cover clicks into place.
Maintenance
49
PowerLite Home Cinema 1080.book Page 50 Tuesday, February 5, 2008 4:46 PM
Replacing the Lamp
The projection lamp lasts for up to 3000 hours. You can use the
Info
menu to check how
long it’s been in use (see page 53). It’s time to replace the lamp when:
■
The projected image gets darker or starts to deteriorate.
Warning light
■
The projector’s warning light flashes red at half-second intervals.
■
The message
Replace the lamp when you start projecting.
appears on the screen
Note:
Lamp life results will vary depending on mode selected, environmental conditions, and usage.
Turn off this product when not in use to prolong the life of the projector.
You can purchase lamp part number V13H010L39 from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit
www.epsonstore.com
(U.S. sales) or
www.epson.ca
(Canadian sales).
Be sure to read the “Important Safety Information” on page 67 before replacing the lamp.
Warning:
Let the lamp cool fully (about 1 hour) before replacing it. In the unlikely event that the lamp has broken, small glass fragments may be present and should be removed carefully to avoid injury.
Caution:
Never touch the glass portion of the lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Follow these steps to replace the lamp:
1. Press the
P
Power
button and wait for the light to stop flashing.
2. Turn off the power switch on the back of the projector.
3. Unplug the power cord and any cables.
4. Wait about an hour to make sure the lamp is no longer hot.
50
Maintenance
PowerLite Home Cinema 1080.book Page 51 Tuesday, February 5, 2008 4:46 PM
5. Press in the latches securing the lamp cover and lift off the cover.
6. Loosen the two screws securing the lamp (they don’t come all the way out).
7. Grasp the bottom of the lamp as shown and pull it straight out.
Warning:
The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
Maintenance
51
PowerLite Home Cinema 1080.book Page 52 Tuesday, February 5, 2008 4:46 PM
8. Gently insert the new lamp and tighten its screws.
Caution:
Don’t touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure.
9. Replace the lamp cover. (The projector won’t work if the lamp cover is open or loose.)
10. Reset the lamp usage timer, as described on page 52.
Resetting the Lamp Usage Timer
After replacing the lamp, plug the projector back in, turn on the power switch on the back, and press the
P Power
button. Then follow these steps to reset the lamp usage timer:
1. Press the
Menu
button on the projector or remote control.
2. Use the menu navigation buttons to open the
Reset
menu, then select
Reset Lamp
Hours
.
3. When you see a confirmation prompt, highlight
Yes
and press the
Select
button.
4. When you’re finished, press the
Menu
button to exit.
The lamp usage timer shows 0H until you’ve used the lamp for at least 10 hours.
52
Maintenance
PowerLite Home Cinema 1080.book Page 53 Tuesday, February 5, 2008 4:46 PM
Checking the Projector Status
You can use the Info menu to view information about the current display settings and how long the projection lamp has been in use. To access the Info menu:
1. Press the
Menu
button on the projector or remote control.
2. Use the menu navigation buttons to open the
Info
menu. The following information appears:
■
■
■
■
■
Lamp Hours
Source
Input Signal
Resolution
Scan Mode
■
■
■
■
■
Refresh Rate
Sync Info
Video Signal
Deep Color (color depth)
Status (error information)
Note:
The information displayed depends on the currently selected image source. The Lamp
Hours shows 0H until you’ve used the lamp for at least 10 hours.
The resolution indicates the total number of scan lines in the source signal. The number of visible
scan lines depends on the signal format standard and selected display settings (see page 63).
Storing the Projector
If you need to store the projector for an extended time, do the following:
■
■
■
■
Make sure the temperature of the storage area is within 14 to 140 °F (–10 to 60 °C).
Attach the lens cover and retract the feet.
Remove the batteries from the remote control.
Pack the projector in its original packaging or equivalent.
Maintenance
53
PowerLite Home Cinema 1080.book Page 54 Tuesday, February 5, 2008 4:46 PM
Transporting the Projector
Note:
Epson shall not be liable for any damages incurred during transportation.
The projector contains many glass and precision parts. When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials. Be sure the carrier is capable of transporting fragile equipment and is aware that the projector is fragile.
Before transporting the projector, make sure you center the lens by turning the lens shift dials until they click.
54
Maintenance
PowerLite Home Cinema 1080.book Page 55 Tuesday, February 5, 2008 4:46 PM
Problem Solving
This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support.
What To Do When the Lights Come On or Flash
The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.
If the projector isn’t working correctly, first press the
P
Power
button or the
Off
button on the remote control, let the projector cool down, turn off the power switch on the back, and unplug the power cord. Then plug the power cord back in and turn on the projector.
If this doesn’t solve the problem, check the status lights on top of the projector.
Power light
Warning light
Light state Cause and solution
P
Power light does not come on
Make sure the power switch on the back of the projector is turned on and the power cord is connected securely at both ends.
P
Power light is orange The projector is in standby mode. Turn off the power switch in back to turn off the projector, or press the
P
Power button to turn it on.
P
Power light flashes green The projector is warming up. Wait for the picture to appear.
P
Power light flashes orange and you can’t turn the projector on or off using the
P
Power button orange
Warning light flashes
The projector is cooling down. Wait until the light stops flashing and shines orange. Then turn off the power switch in back to turn off the projector, or press the
P
Power button to turn it on.
High-speed cooling is in progress. If the projector gets too hot again, projection stops automatically. Make sure there is plenty of space around and under the projector for ventilation. Clean or
replace the air filter if necessary (see page 48).
Problem Solving
55
PowerLite Home Cinema 1080.book Page 56 Tuesday, February 5, 2008 4:46 PM
Light state
Warning light is red
Warning light flashes red at half-second intervals
Warning light flashes red at one-second intervals
Cause and solution
The projector is too hot, which turns off the lamp automatically.
Let it cool for five minutes, then turn it back on. Make sure there is plenty of space around and under the projector for ventilation.
Also, clean or replace the filter if necessary (see page 48).
If you are using the projector at an altitude above 4900 feet (1500 meters), turn on High Altitude Mode so the fan can properly cool
the projector at the high altitude air pressure (see page 45).
The lamp needs to be replaced (see page 50). Make sure you
have a spare lamp handy. Check to make sure the lamp and lamp cover are securely installed.
There is an internal problem.
Turn off the power switch on the back of the projector, and unplug it from the electrical outlet.
Then contact Epson for assistance (see page 60).
Solving Picture Problems
You cannot turn on the projector.
■
Make sure the power cord is connected and the power switch is turned on. Then wait a moment for the
P Power
light to turn orange before pressing the
P Power
button.
■
If you’ve set the
Operation Lock
, the control panel buttons are disabled; you must use
the remote control to turn on the projector (see page 32).
■
■
■
■
No picture appears on the screen or you see the
No Signal
message displayed.
■
Press the
Source
button on the projector or one of the
Source
buttons on the remote control to select the correct input source. Allow a few seconds for the projector to sync up after pressing the button.
■
Press the
Blank off temporarily.
button on the remote control to make sure the picture hasn’t been turned
Check that the
P Power
light is green, not flashing, and the lens cover is off.
The projector may be in standby (or sleep) mode. If the the
P Power
button to turn the projector back on.
P
Power
light is orange, press
Make sure your video equipment is turned on.
Make sure your cable(s) are connected correctly (see page 18).
56
Problem Solving
PowerLite Home Cinema 1080.book Page 57 Tuesday, February 5, 2008 4:46 PM
You’re using a computer and no picture appears on the screen.
If you’re using a Windows laptop:
■
Press the function key that lets you display on an external monitor. It’s often labeled with an icon such as , but it may also be labeled
CRT/LCD
. You may have to hold down the
Fn
key while pressing it. Check your laptop’s manual or online help.
■
On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time. Allow a few seconds for the projector to sync up after pressing it.
If the function key doesn’t let you display simultaneously on both screens, you might need to use the Display utility in the Windows Control Panel to make sure that both the
LCD screen and external monitor port are enabled. From the Windows Control Panel, open the
Display
utility. In the Display Properties dialog box, click the
Settings
tab, then click
Advanced
. The method for adjusting the setting varies from computer to computer; you may need to click a
Monitor
tab, then make sure the external Monitor port is set as your primary display or enabled. See your computer manual or online help for details.
If you’re using Mac OS X:
1. Select
System Preferences
from the Apple menu and click
Displays
.
2. Click
Detect Displays
.
3. To display the entire desktop on both your projector screen and LCD screen, click the
Arrangement
or
Arrange
tab. (If you don’t see this tab, make sure it isn’t hidden by another window.)
4. Click
Mirror Displays
in the lower corner of the screen. One of the monitor icons automatically moves on top of the other.
Click here
Problem Solving
57
PowerLite Home Cinema 1080.book Page 58 Tuesday, February 5, 2008 4:46 PM
The picture is upside-down or reversed.
Change the
Projection
setting in the Settings menu (see page 44).
■
■
■
Only part of the picture is displayed, or the picture is distorted.
■
■
Press the
Aspect
button to select a different aspect ratio (see page 28).
If the Aspect is set to
Zoom
, you may need to use the
Zoom Caption Pos. option to see
the top or bottom section of the screen so that subtitles are visible (see page 43).
Check the
Use the
Output Scaling
Position
to make sure it’s adjusted correctly (see page 43).
setting to reposition the image on the screen (see page 43).
If you’ve connected a computer and you see only half the image, make sure the computer’s Dual Display setting is turned off.
The picture isn’t rectangular.
■
If the image looks like or , the projector has been placed off to one side of the screen and angled toward it. Face the projector straight ahead (instead of at the center of
the screen), then use the horizontal lens shift dial to center the image (see page 25).
■
If the image looks like or , make sure the projector is not tilted up or down.
■
■
The picture contains static or noise.
■
Make sure the
Input Signal
is set correctly for your connected video equipment (see
■
If you’re viewing still images and you notice flickering or horizontal lines, turn on the
Progressive
Make sure your cables are securely connected at both ends.
If you’re using an extension cable, you may pick up interference if the cable is not adequately shielded. You may need to use a signal amplifier for longer cables.
■
If you’re displaying the same image on your computer and projector screen, try turning
off your laptop’s LCD display (see page 57).
The picture is blurry.
■
■
■
Make sure the
Input Signal
is set correctly for your video equipment (see page 44).
There may be dirt on the lens. Clean the lens as described on page 47.
Adjust the focus (see page 27).
58
Problem Solving
PowerLite Home Cinema 1080.book Page 59 Tuesday, February 5, 2008 4:46 PM
■
■
■
Make sure the lens is not fogged by condensation. If you’ve just moved the projector from a cold environment, wait a couple of minutes before using it.
Adjust the
Sharpness
If you’re projecting from a computer, you may need to adjust the
Tracking
and
Sync
■
■
■
The colors on the screen don’t look right.
■
Make sure the
Input Signal
is set correctly for your connected video equipment (see
■
Press the
Color Mode button on the remote control to select a different color mode (see
Check the brightness and contrast settings (see page 35).
Fine-tune the colors with the settings listed on page 38.
If the picture looks dark, you may need to replace the lamp. Check the lamp usage timer
to see how long the lamp has been in use (see page 53). Replace the lamp if it’s close to
the end of its service life (see page 50).
Solving Remote Control Problems
■
■
■
■
The projector doesn’t respond to remote control commands.
■
Make sure you’re within about 30 feet of the projector, and the remote control is not angled away from the projector by more than 30° in any direction.
You may need to replace the remote control batteries (see page 21).
Dim the room lights and turn off any fluorescent lights. Make sure the projector is not in direct sunlight.
Turn off nearby equipment that emits infrared energy, such as a radiant room heater.
Make sure there are no objects between the remote control and the IR receiver.
Problem Solving
59
PowerLite Home Cinema 1080.book Page 60 Tuesday, February 5, 2008 4:46 PM
Where To Get Help
Internet Support
Epson provides technical assistance 24 hours a day at
epson.com/support
.
Here you can access troubleshooting information, download product documentation, and receive technical advice through e-mail.
Speak to a Support Representative
To use the Epson PrivateLine Support service, call
(800) 637-7661
and enter the PIN on the
Epson PrivateLine Support card that came with your projector. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6
AM
to 6
PM
, Pacific
Time, Monday through Friday, for the duration of your warranty period.
You may also speak with a projector support specialist by dialing one of these numbers:
■
■
U.S.:
(562) 276-4394
Canada:
, 6
(905) 709-3839
AM
, 6
to 6
AM
PM
to 6
, Pacific Time, Monday through Friday
PM
, Pacific Time, Monday through Friday
Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Before you call, please have the following information ready:
■
■
■
■
Product name (PowerLite Home Cinema 1080)
Product serial number (located on the bottom of the projector)
Computer configuration, if you’re connected to a computer
Description of the problem
Purchase Supplies and Accessories
You can purchase screens, carrying cases, or other accessories from an authorized Epson reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). To purchase online, visit
www.epsonstore.com
(U.S. sales) or
www.epson.ca
(Canadian sales).
60
Problem Solving
PowerLite Home Cinema 1080.book Page 61 Tuesday, February 5, 2008 4:46 PM
Specifications
General
Type of display
Size of LCD panels
Lens
Resolution
(native format)
Brightness
Dynamic contrast ratio
Image size
Projection distance
Zoom ratio
Aspect ratio
Fan noise level
Poly-silicon TFT active matrix
0.74 inch (18 mm) wide
F=2.0 to 3.17
1920 × 1080 pixels, 1080p
1200 ANSI lumens maximum
12000:1
30 to 300 inches
2.8 to 62.8 feet (0.87 to 19.15 m) at 16:9
3.5 to 76.9 feet (1.06 to 23.44 m) at 4:3
1-2.1
16:9 or 4:3
26 to 33 dB
Lamp
Note:
Lamp life results will vary depending on mode selected, environmental conditions, and usage.
Turn off this product when not in use to prolong the life of the projector.
Type
Power consumption
Lamp life
Part number
UHE (Ultra High Efficiency), E-TORL
170 W
1700 to 3000 hours, depending on usage
V13H010L39
Remote Control
Range
Batteries
Approximately 30 feet (10 m)
AA × 2
Specifications
61
PowerLite Home Cinema 1080.book Page 62 Tuesday, February 5, 2008 4:46 PM
Dimensions
Height
Width
Depth
Weight
Electrical
Rated frequency
Power supply
4.9 inches (124 mm); not including adjustable feet
16 inches (406 mm)
12.2 inches (310 mm); not including lens protrusion
12.3 lb (5.6 kg)
Power consumption
50/60 Hz AC
100 to 120 VAC, 2.7 A
200 to 240 VAC, 1.2 A
Operating: 245 W (100 to 120V), 240 W (200 to 240 V)
Standby: 4 W (100 to 120V), 5 W (200 to 240 V)
Environmental
Temperature
Humidity
Operating altitude
Operating: 41 to 95 °F (5 to 35 °C)
Storage: 14 to 140 °F (–10 to 60 °C)
Operating: 20 to 80% RH, non-condensing
Storage: 10 to 90% RH, non-condensing
0 to 7500 feet (0 to 2286 meters)
Safety
United States
Canada
FCC Part 15B Class B (DoC)
UL60950-1
ICES-003 Class B
CSA C22.2 No. 60950-1
Pixelworks DNX
™
ICs are used in this projector.
62
Specifications
PowerLite Home Cinema 1080.book Page 63 Tuesday, February 5, 2008 4:46 PM
Compatible Video Formats
The projector supports analog video in NTSC, PAL, and SECAM formats, and it automatically adjusts to the incoming signal. It can receive these formats as composite video, S-video, or component video— which it accepts through the Video, S-Video, and Component ports, respectively.
The projector also supports digital video (SDTV, HDTV) and various monitor display formats. Digital video is accepted by the HDMI and Component video ports. The PC port accepts analog RGB computer monitor signals.
If necessary, you can select a different Aspect setting to optimize the image. The resolution at which the image displays for a given setting depends on the currently active picture source, as listed in the following tables.
Composite video or S-Video
Aspect setting
Format
Normal
(4:3) Full
Zoom
(16:9)
Wide
(16:9)
NTSC
PAL or SECAM
Resolution
720 × 480
720 × 360
720 × 576
720 × 432
1440 × 1080 1920 × 1080
1440 × 1080 1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
Component video
Format/
Signal
Aspect setting
Resolution Normal Full
SDTV
480i
625i
480p
625p
HDTV
720p
1080i
1080p
720 × 480
720 × 576
720 × 480
720 × 576
1280 × 720
1920 × 1080
1920 × 1080
(4:3)
1440 × 1080
1440 × 1080
1440 × 1080
1440 × 1080
(16:9)
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
---
Zoom
(16:9)
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
Wide
(16:9)
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
--
Note:
The signal name refers to the total number of visible scan lines and the display mode
(interlaced or progressive), as defined by the signal format.
Specifications
63
PowerLite Home Cinema 1080.book Page 64 Tuesday, February 5, 2008 4:46 PM
Analog RGB
Signal
(4:3)
VGA*
VESA
SVGA
XGA
SXGA
WXGA
MAC13”
MAC16”
MAC19”
SDTV*
480i
480p
625i
625p
HDTV*
720p
1080i
1080p
Resolution Normal Full
Aspect setting
Zoom Wide
640 × 480
640 × 480
800 × 600
1440 × 1080
1440 × 1080
1440 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1024 × 768 1440 × 1080 1920 × 1080 1920 × 1080 1920 × 1080
1280 × 1024
1280 × 960
1280 × 768
1360 × 768
640 × 480
832 × 624
1024 × 768
1350 × 1080
1440 × 1080
1800 × 1080
1912 × 1080
1440 × 1080
1440 × 1080
1440 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
720 × 480
720 × 480
720 × 576
720 × 576
1440 × 1080
1440 × 1080
1440 × 1080
1440 × 1080
--
1280 × 720
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
--
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
1920 × 1080
---
* HDMI input signals
64
Specifications
PowerLite Home Cinema 1080.book Page 65 Tuesday, February 5, 2008 4:46 PM
ESC/VP21 Command Codes
You can use an AV controller with a 9-pin null modem serial cable to control the projector. You can download the complete
ESC/VP 21 Communication Manual
for home theater projectors from the
Epson website at
epson.com/support
. Following are some of the available codes:
Item
Power ON/OFF
A/V Mute ON/OFF
A/V Mute selection
Source change
ON
OFF
ON
OFF
Black
Blue
Signal name
Component video
Terminal
Component
YCbCr
YPbPr
Auto
PC HDB15
Input 3 (HDMI)
RGB
HDMI
Video Video/S-Video
Video (RCA)
Input 5
S-Video
Digital video
YCbCr
YPbPr
Color Mode
Auto
Theatre
Living Room
Natural
Dynamic
Theatre Black 1
Theatre Black 2
Command
PWR ON
PWR OFF
MUTE ON
MUTE OFF
MSEL 00
MSEL 01
SOURCE 10
SOURCE 14
SOURCE 15
SOURCE 1F
SOURCE 21
SOURCE 30
SOURCE 41
SOURCE 42
SOURCE C0
SOURCE C4
SOURCE C5
SOURCE CF
CMODE 05
CMODE 06
CMODE 07
CMODE 08
CMODE 09
CMODE 0A
Specifications
65
PowerLite Home Cinema 1080.book Page 66 Tuesday, February 5, 2008 4:46 PM
Item
Aspect ratio Auto
Normal
Full
Zoom
Wide
Command
ASPECT 00
ASPECT 20
ASPECT 21
ASPECT 22
ASPECT 25
66
Specifications
PowerLite Home Cinema 1080.book Page 67 Tuesday, February 5, 2008 4:46 PM
Notices
Important Safety Information
■
■
■
■
Follow these safety instructions when setting up and using the projector:
■
■
■
■
■
■
■
■
■
■
Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on.
Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you.
Except as specifically explained in this
User’s Guide
, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.
Don’t place the projector on an unstable cart, stand, or table. Also, don’t use the projector near water or sources of heat.
Use the type of power source indicated on the projector. If you’re not sure of the power available, consult your dealer or power company.
Place the projector near a wall outlet where the plug can be easily unplugged.
Don’t insert the plug into an outlet with dust present, and insert the plug firmly into the outlet.
Failure to do so could result in sparks or fire.
Don’t overload wall outlets, extension cords, or integral convenience receptacles. This can cause fire or electric shock.
Don’t block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Don’t operate the projector on a sofa, rug, or other soft surface, or in a closed-in cabinet unless proper ventilation is provided.
Never push objects through the cabinet slots or spill liquid into the projector.
Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: when the power cord or plug is damaged or frayed; if liquid has been spilled into the projector, or if it has been exposed to rain or water; if it doesn’t operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service; if it has been dropped or the housing has been damaged.
Don’t place the projector where the cord can be walked on. This may result in fraying or damage to the plug.
Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.
Notices
67
PowerLite Home Cinema 1080.book Page 68 Tuesday, February 5, 2008 4:46 PM
■
■
■
■
■
■
■
■
The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
Allow the lamp to cool for one hour before replacing it.
Unplug the projector during lightning storms or when not in use for extended periods.
Don’t place the projector or remote control on top of heat-producing equipment.
If you use the projector in a country other than where you purchased it, use the correct power cord for that country.
Don’t stand on the projector or place heavy objects on it.
Don’t use the projector outside of the required temperature range of 41 to 95 °F
(5 to 35 °C). Doing so may cause an unstable display and could lead to projector damage.
Don’t store the projector outside of the required temperature range of 14 to 140 °F
(–10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case.
WARNING:
The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm.
Wash hands after handling
.
(posted in accordance with Proposition 65 in Cal. Health & Safety
Code § 2549.5 et seq)
68
Notices
PowerLite Home Cinema 1080.book Page 69 Tuesday, February 5, 2008 4:46 PM
FCC Compliance Statement
For United States Users
■
■
■
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
■
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC
Certification of this device and may cause interference levels which exceed the limits established by the
FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
For Canadian Users
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Notices
69
PowerLite Home Cinema 1080.book Page 70 Tuesday, February 5, 2008 4:46 PM
Declaration of Conformity
According to 47CFR, Part 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU
Boards and Power Supplies used with Class B Personal Computers:
We:
Located at:
Epson America, Inc.
3840 Kilroy Airport Way
MS 3-13
Long Beach, CA 90806-2469
Telephone: (562) 290-5254
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and
15 of the FCC rules as a Class B digital device. Each product marketed is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR §2.909. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Trade Name:
Type of Product:
Model:
Marketing Name:
Epson
Projector
EMP-TW-1000
PowerLite Home Cinema 1080
70
Notices
PowerLite Home Cinema 1080.book Page 71 Tuesday, February 5, 2008 4:46 PM
Epson America, Inc. Limited Warranty
Basic Two-Year Warranty and 90-Day Lamp Warranty
What Is Covered:
Epson America, Inc. (“Epson”) warrants to the original retail purchaser of the Epson product enclosed with this limited warranty statement that the product, if purchased new and operated in the United States or Canada, will be free from defects in workmanship and materials for a period of two (2) years from the date of original purchase (except that the warranty period is 90 days for projector lamps). For warranty service, you must provide proof of the date of original purchase.
What Epson Will Do To Correct Problems:
If your product requires service, Epson will ask you to bring the product securely packaged in its original container or equivalent, along with proof of the date of original purchase, to your Epson Dealer or Epson Customer Care Center as instructed by Epson.
Epson will, at its option, repair or replace the defective unit, without charge for parts or labor. When warranty service involves the exchange of the product or of a part, the item replaced becomes Epson property. The exchanged product or part may be new or previously refurbished to the Epson standard of quality, and at Epson’s option, the replacement may be another model of like kind and quality.
Epson’s liability for replacement of the covered product will not exceed the original retail selling price of the covered product. Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty. However, each replacement lamp carries the limited 90-day warranty stated above.
What This Warranty Does Not Cover:
This warranty does not apply to refurbished or reconditioned products. This warranty covers only normal use of the product. 24-hour-per-day or other excessive continual use causes strain and is not considered normal use. This warranty does not cover consumables (e.g., fuses), other than lamps. This warranty is not transferable. Epson is not responsible for warranty service should the Epson label or logo or the rating label or serial number be removed.
Epson is not responsible for warranty service should the product fail to be properly maintained or fail to function properly as a result of misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, improper electrical current, software problems, interaction with non-Epson products, or service other than by an Epson Authorized
Servicer. Postage, insurance, or shipping costs incurred in presenting your Epson product for carry-in warranty service are your responsibility. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES.
IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED
TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY
STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE
VOID. IN THE EVENT THE REMEDIES ABOVE FAIL, EPSON’S ENTIRE LIABILITY SHALL
BE LIMITED TO A REFUND OF THE PRICE PAID FOR THE EPSON PRODUCT
Notices
71
PowerLite Home Cinema 1080.book Page 72 Tuesday, February 5, 2008 4:46 PM
COVERED BY THIS LIMITED WARRANTY. EXCEPT AS PROVIDED IN THIS WRITTEN
WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS AFFILIATES SHALL BE LIABLE
FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR
INABILITY TO USE THE EPSON PRODUCT, WHETHER RESULTING FROM BREACH OF
WARRANTY OR ANY OTHER LEGAL THEORY.
In Canada, warranties include both warranties and conditions. Some jurisdictions do not allow limitations on how long an implied warranty lasts and some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from jurisdiction to jurisdiction.
To find the Epson Authorized Reseller nearest you, visit our website at: www.epson.com.
To find the Epson Customer Care Center nearest you, visit epson.com/support.
You can also call the Epson Connection
SM
at (800) 637-7661 + PIN or (562) 276-4394 in the U.S. and (905) 709-3839 in Canada or write to:
Epson America, Inc., P.O. Box 93012, Long Beach, CA 90809-3012.
72
Notices
PowerLite Home Cinema 1080.book Page 73 Tuesday, February 5, 2008 4:46 PM
Index
A
Abs. Color Temp. setting, 30, 38
Air filter
cleaning and replacing, 48 to 49
Aspect ratio, selecting, 28, 43
B
Brightness
Brightness Control setting, 37
Buttons
C
Cleaning
air filter, 48 to 49 lens and projector case, 47, 48
Color
Color temperature setting, 30, 38
Component video connection, 19
Computer
Contrast
D
Display Background setting, 44
E
Epson
Index
73
PowerLite Home Cinema 1080.book Page 74 Tuesday, February 5, 2008 4:46 PM
F
Air filter
G
H
I
Image
Installing projector, 16 to 18
K
Kensington anti-theft device, 8, 11
L
Lamp
Lock
M
Memory settings
Menus
N
74
Index
PowerLite Home Cinema 1080.book Page 75 Tuesday, February 5, 2008 4:46 PM
O
P
Positioning image, 25 to 26, 43
Positioning projector, 13 to 16
Problems
indicator lights, 55 to 56 picture, 56 to 59
Projection Distance Calculator, 15
Projector
turning on and off, 22 to 23, 56
R
Remote control
Resetting
Resolution
S
Skin Tone
Specifications
compatible video formats, 63 to 64
dimensions, 62 electrical, 62 environmental, 62
general, 61 lamp, 61 remote control, 61
Index
75
PowerLite Home Cinema 1080.book Page 76 Tuesday, February 5, 2008 4:46 PM
Sync (Synchronization) setting, 40
T
Turning on and off projector, 22 to 23, 56
V
Video, compatible formats, 63 to 64
W
Z
Zoom Caption Pos. setting, 28, 43
76
Index
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project