Wireless CONNECTIVITY that extendS your industrial network to the edge Introduction Product Overview............................................................................................20 - 21 Product Selection Guide...................................................................................22 - 28 Wireless Solutions Cellular Routers...............................................................................................30 - 51 Wireless Remote I/O........................................................................................52 - 57 Radio Modems.................................................................................................58 - 63 Wireless Ethernet Bridges/Routers...................................................................64 - 67 Wireless Serial Servers....................................................................................66 - 67 Wireless Access Point......................................................................................68 - 69 Wi-Fi Embedded Modules................................................................................72 - 73 Wi-Fi Access Point Modules.............................................................................76 - 77 Wireless Ethernet GhostBridge.........................................................................78 - 79 WIRELESS Extend Your Industrial Network To The Edge B&B Electronics has been expanding and reinforcing its reputation as a global source for best-in-class rugged, reliable network and data communications products for more than three decades. And today, increasingly, wireless is the solution of choice for M2M device connectivity. • Vehicle Telematics & Diagnostics • Security & Access Control • Industrial Automation Test & Measurement • Water and Waste-water treatment • Monitoring and Instrumentation • Medical Equipment • Energy Management • Retail / Point of Sale Products • Metrology, Alarm and Warning Systems WIRELESS SOLUTIONS CELLULAR ROUTERS • • • GPRS / EDGE / UMTS / HSDPA / HSUPA / HSPA+ routers 3G routers are equipped with 10/100 Ethernet port and optional interfaces (RS-232, RS-422, RS-485, Modbus or I/O) Wi-Fi 802.11a/b/g/n access point WIRELESS I/O AND RADIO MODEMS • • • • • • • • 20 2.4 GHz short range, 900 MHz long range (Class 1/Division 2) IP30 ingress protection rated Top of the line AES security Wide temperature range (-40 to +80˚C) Low latency response rates Modbus compatible Dual power, 10-40VDC or 24VAC Outdoor IP67 rated models WI-FI ETHERNET BRIDGES, ROUTERS, SERIAL DEVICE SERVERS, AND ACCESS POINTS • Wide temperature (-40 to +85°C), environmental specifications • Plug-n-play serial and Ethernet to 802.11a/b/g/n connectivity • Enterprise Class wireless security (WPA2/WPA-Enterprise, WPA2/WPAPreShared Key, WEP, Open, EAP, 802.11i) • AirborneM2M Management Center™ - device discovery, control and management • Variable 5-36 VDC power supply • AirborneM2M SpeedLink roaming for enhanced connection reliability • Supports Airborne Portflex technology for advanced port configuration and routing • Compact form factor in a rugged metal box • Access point & wireless router with serial device server support WI-FI EMBEDDED MODULES HIGH-SPEED WIRELESS ETHERNET BRIDGE • • • • • • • • • • • • Wide operating temperature (-40 to +85°C) Enterprise Class wireless security (WPA2/WPA-Enterprise, WPA2/WPAPreShared Key, WEP, Open, EAP, 802.11i) 32-bit ARM9 processor with 802.11a/b/g/n radio for increased range and throughput Airborne Management Center – discover, control, manage devices Advanced low power modes for power save applications Access point & wireless router with serial device server support Secure, long-range Ethernet Fast, easy and secure high-speed wireless Ethernet right out of the box. Zero set-up — just aim it, mount it and plug it in. 80° 15 dBi sector antenna integrated into the housing 5 GHz radio built from 802.11n 2X2 MIMO technology for long range connectivity (15 km/9 mi) Temperature range of -30 to +80°C UV stable plastic case rated for outdoor use Maximum data rate of 150 Mbps Class 1/Division 2 Certified For Hazardous Locations Zlinx® Xtreme Radio Modems & I/O Zlinx® Standard Long-range Radio Modem Zlinx® Standard Wireless I/O For applications that require C1/D2 certification, B&B Electronics has a range of connectivity and communication solutions designed to operate in hazardous environments. LISTED - see page 470 for a complete listing of C1D2 products. www.bb-elec.com 21 WIRELESS Wireless Connectivity which is right for you? CEllular - North America PRODUCT FAMILY Cellular Router Cellular Router Product series Spectre 3G Spectre 3G WiFi GPRS ✔ ✔ UMTS/HSPDA ✔ ✔ UMTS/HSPA+ ✔ ✔ CDMA 2000 1X, EV-DO REV A,B ✔ ✔ MOBILE WIRELESS NETWORK TECHNOLOGY Wi-Fi Ethernet ✔ COMMUNICATION INTERFACES AND EXPANSIONS Ethernet 10/100 ✔ Ethernet 10/100 3-port switch ✔ Wi-Fi (IEEE 802.11 b,g,n) USB Host ✔ ✔ ✔ ✔ RS232/RS422/RS485 ✔ ✔ MBUS, Wireless MBUS ✔ ✔ I/O CNT ✔ ✔ I/O CNT (1xIN/1xOUT) ✔ ✔ Metal Casing (42x80x113 mm/1.7x3.1x4.5 in)) ✔ ✔ 2xSIM Card ✔ ✔ Antenna Rx Diversity ✔ ✔ Power Supply 10V - 30V DC ✔ ✔ Operating Temperature -30° to +60° C ✔ ✔ DIN holder TS35/TS32 ✔ ✔ DESIGN, DIMENSIONS, SIM, ENVIRONMENTAL 22 continued... PRODUCT FAMILY Cellular Router Cellular Router Product series Spectre 3G Spectre 3G WiFi Linux ✔ ✔ IPSec (DES, 3DES, AES, MD5, SHA-1, DH2, DH5) ✔ ✔ OpenVPN, PPTP, L2TP, GRE ✔ ✔ Authentication (X509 certification, Pre-shared Key, PW) ✔ ✔ EasyVPN ✔ ✔ Firewall ✔ ✔ DHCP ✔ ✔ NAT/PAT ✔ ✔ HTTP/HTTPS Server ✔ ✔ Telnet/SSH ✔ ✔ DynDNS ✔ ✔ FTP Server ✔ ✔ NTP Server, NTP Client ✔ ✔ SNMP ✔ ✔ VRRP ✔ ✔ SMTP, E-mail ✔ ✔ SMS Functions ✔ ✔ VLAN 802.1Q ✔ ✔ QoS, IGMP, BGP, OSPF, RIP ✔ ✔ PPPoE Bridge ✔ ✔ COM Port TCP/UDP server/client ✔ ✔ Modbus RTU/TCP Gateway ✔ ✔ 4 Configuration Profiles ✔ ✔ Automatic Configuration and FW Upgrade ✔ ✔ 34 36 FUNCTIONS Page www.bb-elec.com 23 WIRELESS Wireless Connectivity which is right for you? CEllular PRODUCT FAMILY Cellular Router Cellular Router Cellular Router Cellular Router Cellular Router Cellular Router Cellular Router Product series ER75i v2 UR5i v2 Libratum UR5i v2 LR77 v2 CR10 v2 UCR11 v2 XR5i v2 MOBILE WIRELESS NETWORK TECHNOLOGY GPRS ✔ ✔ ✔ ✔ UMTS/HSPDA ✔ ✔ ✔ ✔ ✔ UMTS/HSPA+ ✔ ✔ ✔ ✔ LTE ✔ CDMA 2000 1X, EV-DO Rev A,B WAN Ethernet optional optional optional optional ✔ ✔ optional optional ✔ ✔ COMMUNICATION INTERFACES AND EXPANSIONS Ethernet 10/100 ✔ Ethernet 10/100 3-port switch optional Wi-Fi (IEEE 802.11 b,g,n) optional 2x ✔ ✔ optional optional optional optional optional optional ✔ ✔ ✔ ✔ ✔ RS232/RS422/RS485 optional optional optional optional optional optional MBUS, Wireless MBUS optional optional optional optional optional optional I/O CNT optional optional optional optional optional optional ✔ ✔ ✔ ✔ ✔ ✔ optional optional optional optional optional optional optional optional optional optional optional optional optional optional ✔ optional optional optional optional ✔ ✔ ✔ optional ✔ I/O CNT (1xIN/1xOUT) GPRS Receiver DESIGN, DIMENSIONS, SIM, ENVIRONMENTAL Plastic Casing optional (50x83x116 mm/2.0x3.3x4.6 in) Metal Casing optional (42x80x113 mm/1.7x3.1x4.5 in) 2xSIM Card optional Antenna Rx Diverity 24 ✔ optional ✔ USB Host optional ✔ optional optional Power Supply 10V - 30V DC ✔ ✔ ✔ ✔ ✔ ✔ Operating Temp. -30° to +60° C ✔ +70°C ✔ ✔ ✔ ✔ ✔ DIN holder TS35/TS32 ✔ ✔ ✔ ✔ ✔ ✔ ✔ continued... PRODUCT FAMILY Cellular Router Cellular Router Cellular Router Cellular Router Cellular Router Cellular Router Cellular Router Product series ER75i v2 UR5i v2 Libratum UR5i v2 LR77 v2 CR10 v2 UCR11 v2 XR5i v2 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ FUNCTIONS Linux IPSec (DES, 3DES, AES, MD5, SHA1, DH2, DH5) OpenVPN, PPTP, L2TP, GRE Authentication (X509 certification, Pre-shared Key, PW) EasyVPN optional optional optional optional optional optional optional Firewall ✔ ✔ ✔ ✔ ✔ ✔ ✔ DHCP ✔ ✔ ✔ ✔ ✔ ✔ ✔ NAT/PAT ✔ ✔ ✔ ✔ ✔ ✔ ✔ HTTP/HTTPS Server ✔ ✔ ✔ ✔ ✔ ✔ ✔ Telnet/SSH ✔ ✔ ✔ ✔ ✔ ✔ ✔ DynDNS ✔ ✔ ✔ ✔ ✔ ✔ ✔ FTP Server ✔ ✔ ✔ ✔ ✔ ✔ ✔ NTP Server, NTP Client ✔ ✔ ✔ ✔ ✔ ✔ ✔ SNMP ✔ ✔ ✔ ✔ ✔ ✔ ✔ VRRP ✔ ✔ ✔ ✔ ✔ ✔ ✔ SMTP, E-mail ✔ ✔ ✔ ✔ ✔ ✔ ✔ SMS Functions ✔ ✔ ✔ ✔ ✔ ✔ ✔ VLAN 802.1Q ✔ ✔ ✔ ✔ ✔ ✔ ✔ optional optional optional optional optional optional optional PPPoE Bridge ✔ ✔ ✔ ✔ ✔ ✔ ✔ COM Port TCP/UDP server/client ✔ ✔ ✔ ✔ ✔ ✔ optional optional optional optional optional optional QoS, IGMP, BGP, OSPF, RIP Modbus RTU/TCP Gateway 4 Configuration Profiles Automatic Configuration and FW Update ADDITIONAL SOFTWARE SUPPORT SW Plug-in Modules Page ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ 38 40 42 44 46 48 50 www.bb-elec.com 25 WIRELESS Wireless Connectivity which is right for you? Wireless Base I/O PRODUCT FAMILY Wireless I/0 Wireless I/O Wireless I/O Wireless I/O Wireless I/O Product series Zlinx Xtreme Zlinx Xtreme Zlinx Standard Zlinx Standard Zlinx Standard 900 MHz 2.4 GHz 900 MHz 2.4 GHz 868 MHz 1W 63mW 1W 63mW 316 mW 115 Kbps or 9600 bps 250 Kbps 115 Kbps or 9600 bps 250 Kbps 24 Kbps 256 Bit 128 Bit 256 Bit 128 Bit 128 Bit 14 mi/22.5 km 1 mi/1.6 km 14 mi/22.5 km 1 mi/1.6 km 25 mi/40 km 3000 ft/ .91 km 300 ft/ 91 m 3000 ft/ 91 km 300 ft/ 91 m 1800 ft/549 m ✔ ✔ Max Digital Inputs/Outputs (base) 2 2 4 4 4 Max Analog Inputs/Outputs (base) 2 2 2 2 2 ✔ ✔ ✔ ✔ ✔ Frequency Max TX Power Over-the-air Data Rate AES Encryption Range (outdoor) w/Supplied Antenna (line of sight) Range (indoor) w/Supplied Antenna (line of sight) Enclosure IP67 Serial 232/422/485 Accepts IO Expansion Modules Repeater Mode ✔ ✔ DC Input 10 - 40 VDC DC Input 10 - 30 VDC ✔ ✔ ✔ Modbus RTU/ASCII ✔ ✔ Operating Temp (-40 to 74°C) ✔ ✔ AC Input 24 VAC ✔ ✔ ✔ ✔ ✔ ✔ ✔ Operating Temp (-40 to 80°C) ✔ ✔ Class 1/Division 2 ✔ ✔ 54 54 NEMA TS2 Page 26 52 52 54 Wireless Radio Modems Radio Modem Radio Modem Radio Modem Radio Modem Radio Modem Zlinx Xtreme Zlinx Xtreme Zlinx Standard Zlinx Standard Zlinx Standard 900 MHz 2.4 GHz 900 MHz 2.4 GHz 868 MHz 1W 63 mW 1W 63 mW 316 mW 115 Kbps or 9600 bps 250 Kbps 115 Kbps or 9600 bps 250 Kbps 24 Kbps 256 Bit 128 Bit 256 Bit 128 Bit 128 Bit 14 mi/22.5 km 1 mi/1.6 km 14 mi/22.5 km 1 mi/1.6 km 25 mi/40 km 3000 ft/ 91 km 300 ft/ 91 m 3000 ft/ 91 km 300 ft/ 91 m 1800 ft/549 m ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ 58 58 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ 62 62 62 www.bb-elec.com 27 WIRELESS Wireless Connectivity which is right for you? Wireless Base I/O PRODUCT FAMILY Product series 802.11a/b/g/n Bridge/Routers, Ethernet Bridge/Routers Ethernet Serial Servers Ethernet Bridge GhostBridge AirborneM2M Industrial AirborneM2M Embedded Modules ✔ ✔ ✔ ✔ ✔ ✔ 2 UARTS ✔ ✔ ✔ ✔ Access Point Mode (n) ✔ ✔ ✔ ✔ ✔ ✔ ✔ Encrypted Config ✔ ✔ ✔ ✔ SSH/SSL Tunnel ✔ ✔ ✔ ✔ Username/Password ✔ ✔ ✔ ✔ HTTP (Web Server) ✔ ✔ ✔ ✔ DHCP Server ✔ ✔ ✔ ✔ NAT3 Router ✔ ✔ ✔ ✔ Bridge ✔ ✔ ✔ ✔ Command Line Interface ✔ ✔ ✔ ✔ -40°C to +85°C ✔ ✔ ✔ ✔ ✔ Barrel Jack (5VDC) ✔ ✔ ✔ ✔ ✔ ✔ ✔ PoE (802.3af PD) ✔ ✔ WPA/WPA2 Enterprise Terminal Block (5-36VDC) ✔ ✔ ✔ ✔ SAE-J1455 Environmental ✔ ✔ ✔ ✔ FCC (US) ✔ ✔ ✔ ✔ ✔ IC (Canada) ✔ ✔ ✔ ✔ ✔ CE (Europe) ✔ ✔ ✔ ✔ ✔ 64 66 68 72 - 77 78 Page 28 Enterprise & Access Point AirborneM2M Enterprise RS232/422/485 10/100 Ethernet Access Point ✔ The AirborneM2MTM Management Center (AMC) Managing AirborneM2M devices is simple whether you have one or one thousand AirborneM2M Management Center (AMC) brings enterprise class device discovery, control, and management to the world of M2M wireless devices. The application supports individual and group management of all device details: • Configuration and firmware management • Deliver certificates and private keys • Access and monitor groups of devices • Access management (passwords) • Virtual COM port installation • Devices update their firmware in the background • Directly launch web browser for devices from AMC • Supports cloning device configurations across groups of units • Records configuration changes for automatic update logging • Remembers discovered devices, maintains configuration databases • Allows unauthorized devices to be marked as rogue • Automatically informs user of new and unmanaged devices • Predefined device configuration templates available • Included JAVA application runs on Windows, Linux, Mac platforms The AirborneM2M SpeedLink roaming feature provides high level connection reliability, enabling mobile and OEM devices to roam quickly and freely on a wireless network without losing important data or connection. Airborne PowerSave firmware enables OEMs to maximize efficiency and reduce power consumption by up to 70% - critical for battery powered mobile devices. Whether you’re walking around a hospital or driving through a warehouse, SpeedLink ensures you stay connected. www.bb-elec.com 29 WIRELESS Fully Modular Concept – Buy Exactly What You Need FIXED COMMUNICATION INTERFACES: SPECTRE 3G FEATURES: • Ethernet 10/100 • USB Host • I/O port with 1x input and 1x output • 1-2x Ethernet 10/100 with possible modes: - 2-port Ethernet switch - 3-port Ethernet switch - 2x independent LAN - 1x independent LAN and 2-port Ethernet switch • RS-232 serial port Data I/O Port Back up of Primary SIM Auxiliary Optional interfaces to optimize according to your application, with the ability to add additional interfaces in the future: Auxiliary • 2 SIM card holders RS-232, RS-422/485, Modbus Power Connector Ethernet 10/100 Ethernet 10/100, RS-232, RS-422/485, I/O, Modbus • RS-422/485 galvanic separation possible • Modbus master for up to 30 slave meters • I/O CNT interface including 4x binary inputs: 2 inputs may be configured as counter, 2x analogue inputs and 1x binary output 2 or 3-Port Ethernet 10/100 Switch • Wi-Fi 802.11a/b/g/n Certified for use with these networks: AT&T, Verizon, Sprint, T-Mobile, and Rogers Contact B&B Electronics for the latest approvals. 30 HSPA+/UMTS/CDMA/EDGE/GPRS ROUTER ROUTER Spectre 3G CDMA/ GSM router CELLULAR WIRELESS NETWORK TECHNOLOGY MAX MAX DOWNLOAD UPLOAD UMTS/HSPA+ & GPRS/EDGE & CDMA 14.4 Mbps 5.7 Mbps USA, Canada. Check with your local distributor for availability and options. Functions & Software Features B&B Electronics routers offer enhanced functionality, incorporating selfdiagnostics and a hardware watchdog, ensuring secure and consistent operability and ultra-reliable wireless connections. For critical applications, these routers offer SMS and email messaging and control capability for remote alerts and resets. They support the most commonly used LAN/ WAN network protocols and B&B Electronics’s custom software allows for easy, flexible and effective networking and management. Networking • • • • • • • • • • DHCP: automatic IP addressing in LAN network NAT/PAT: IP address and port translation Firewall: filtering of addresses, ports, protocols VRRP: virtual backup router function DynDNS client: access to the dynamic IP address VLAN 802.1Q: virtual LAN QoS: quality of service PPPoE Bridge: PPP over Ethernet Bridge mode Dial-in: communicate over dial CSD call NTP client, NTP server: time synchronization VPN Tunneling • IPSec, OpenVPN, PPTP, L2TP, EasyVPN, GRE • Authentication by certificates, shared keys, name/password Remote Router Supervision & Mass Network Management • • • • HTTP/HTTPS, Telnet/SSH for local and remote configuration and firmware updates Automatic configuration and firmware updates from FTP/HTTP server by schedule Up to 4 independent configuration profiles can be stored and remotely switched using scripts, SMS messages, I/O, etc. Additional software for easy networking and monitoring SmartCLUSTER and R-SeeNet Diagnostics • • • • Detailed logs of operational information, including signal status and data traffic Signal level data, cell identifiers and data traffic are saved in router’s memory for up to 2 months SNMP: router diagnostics, communication with I/O and M-Bus LED indication: signal strength, connection status, ports SMS & Email Info • • • Information about status, connection or disconnection and many others SMS control: on/off connection, switching SIM, router profile, I/O, etc. SMS communication: AT commands (RS232 and TCP/IP), I/O or HTTP Modular LINUX Software Environment Open LINUX based system allows use of common LINUX commands, scripts and other features. B&B Electronics routers offer an extension of standard firmware with optional software plug-ins. You can create your own plug-in and simply apply it to the router. The router has 128kb nonvolatile RAM memory, ready for data collection and processing applications that can be expanded with USB port if desired. Software Plug-ins • • • • • Easy VPN client: secure, encrypted VPN Dynamic routing protocols: BGP, OSPF, RIP QoS: quality of service IGMP: multicast protocols Modbus RTU/TCP gateway and mapping: convert data from RTU to TCP/IP format www.bb-elec.com 31 WIRELESS Spectre 3G Specifications at a Glance Sometimes the answer is isn’t just great products – it is a great solution that is more than the sum of the products. Our engineering support teams can handle special network challenges and provide unique solutions for specific applications. Whether it’s combining cellular routers with wireless radios to support dual cellular networks, or producing a custom product design, B&B Electronics is your best connection for innovative cellular solutions. Data Transfer Technology UMTS/HSPA+ ✔ UMTS/HSUPA ✔ UMTS/HSDPA ✔ GPRS/EDGE ✔ CDMA ✔ Ports & Interfaces - See product details for more information Ethernet 10/100 ✔ USB Host ✔ RS-232 optional RS-485 optional Modbus optional I/O optional 3-Port 10/100 Ethernet Switch optional Ethernet 10/100 WAN Port optional Wi-Fi 802.11b/g/n optional Operating Temperature -30°C to +60°C ✔ Power Supply 10-30 VDC ✔ SIMs SIM card slots (2) ✔ Option Allowing Attachment to DIN Rail Operating System Linux ✔ Basic Functions - See product details for more information VPN-Ipsec ✔ VPN-OpenVPN ✔ VPN-L2TP ✔ VPN-GRE ✔ DHCP ✔ HTTP server ✔ FTP ✔ NAT/PAT ✔ SNMP ✔ VRRP ✔ DynDNS ✔ NTP ✔ Telnet ✔ SSH ✔ PPoE bridge ✔ SMS + e-mail functions ✔ Auto config/FW update ✔ SmartCLUSTER ✔ Select Your Spectre 3G Solution Model No. RT3G-300 RT3G-302 RT3G-304 RT3G-322 RT3G-324 RT3G-330 RT3G-311 RT3G-310 RT3G-300-W RT3G-310-W RT3G-320-W RT3G-330-W RT3G-340-W USA, Canada. Port 1 – – – RS-232 RS-232 12-bit I/O (AI, DI, DO) Ethernet Ethernet – Ethernet RS-232 12-bit I/O (AI, DI, DO) RS-422/485 Check with your local distributor for availability and options. 32 Port 2 – RS-232 RS-422/485 RS-232 RS-422/485 – Ethernet – – – – – – Wi-Fi ✔ ✔ ✔ ✔ ✔ Smart Decisions Begin with Intelligent Management Software R-SeeNet - Monitoring & Management Software R-SeeNet is the software system used for monitoring B&B Electronics routers. It continuously collects information from individual routers in the network and records the data into a SQL database. This data is then presented in a clear and concise dashboard for the Network Administrator to effectively manage their devices. R-SeeNet consists of two parts: R-SeeNet Server A server application that can be programmed to automatically send SNMP queries (Simple Network Management Protocol) to each router defined in the network. The application retrieves status information from the routers and records it in the SQL database. R-SeeNet PHP A web-based application that accesses the SQL database and provides the Network Administrator detailed information on the individual routers and health of the network. Available Data Everything you need to know about your network’s current status as well as a historical view of the information transferred today, yesterday, this week, this month and last month. • • • • • • • • Signal strength Data traffic Response time Router availability Number of PPP connections Number of various channels connected Visual reports, tables and graphs Up to 2 months of past data for each router SmartCLUSTER Internet VPN Portal SmartCLUSTER is software designed to create safe communications systems while using a public network - the Internet. SmartCLUSTER is an OpenVPN server that offers three functions for the creation of safe private networks in a public environment. 1. As an OpenVPN server it connects clients (B&B Electronics routers and end-user computers) via an OpenVPN tunnel. It creates communication links between individual tunnels and thereby enables individual devices to communicate with each other. 2. Based on the user-defined network configuration and connection parameters of VPN tunnels, SmartCLUSTER creates a configuration file for B&B Electronics routers and also creates secure certificates for both sides of the secured OpenVPN tunnel. This allows the user to install individual B&B Electronics routers easily into a virtual private network, confident the system is secure against attacks or unauthorized access. 3. SmartCLUSTER can be used as an instrument for basic network management through information on the connection status of individual routers. The SmartCLUSTER solution • SmartCLUSTER provides solutions for applications where you need to connect devices on local area networks (LANs), and a router. The router provides the communication with the LAN and does not have a public internet IP address. SmartCLUSTER solves problems relevant to network security and the secure connection of individual local networks. • SmartCLUSTER solves the problem of how to connect devices which are behind routers with cellular service sourced from various network operators. www.bb-elec.com 33 WIRELESS Cellular Router - CDMA/HSPA Spectre 3G Series PRODUCT FEATURES • • • • • • • The Spectre 3G cellular router connects Ethernet equipment and remote LANs via the cellular telephone network. It creates secure Ethernet connections in locations where cable connections are impractical, as is so often the case with devices like ATM machines and remote video cameras. The Spectre 3G also creates reliable mobile Ethernet connections. With upload speeds of up to 5.7 Mbps and download speeds of up to 14.4 Mbps, the Spectre 3G provides ample bandwidth, even for applications that require video. The standard configuration includes multiple 10/100 Ethernet ports, one USB host port, one binary input/output (I/O) port and dual SIM card holders. The second SIM card holder provides network redundancy, as the router can automatically switch between cellular service providers if one connection fails. The router supports the creation of VPN tunnels using IPsec, OpenVPN and L2TP. It supports DHCP, NAT, NAT-T, DynDNS, NTP, VRRP, control by SMS, and numerous other functions, as well as additional software like SmartCluster, VPN Server and R-SeeNet. A password-protected Web interface allows users to configure and manage the Spectre 3G from remote locations. The router can automatically upgrade its configuration and firmware from the operator’s central server, allowing for simultaneous mass reconfiguration of every router on the network. Users may insert Linux scripts and they can create up to four different configurations for the same router. Examples would include the SMS and binary input configurations. Users may switch from one configuration to another at any time. 34 Designed for M2M applications Modbus TCP to Modbus RTU Modular design to fit application requirements Dual SIM Cards for redundant backhaul Up to 5.7 Mbps upload/14.4 Mbps download LINUX Platform & Advanced Networking Functions ‘C’ based dev environment to build user applications Ordering Information Model Ethernet USB I/0 Rs232 Number 10/100 RT3G-300 1 1 1 RT3G-302 1 1 1 1 RT3G-304 1 1 1 RT3G-310 2 1 1 RT3G-311 3 1 1 RT3G-322 1 1 1 2 RT3G-324 1 1 1 1 RT3G-330 1 1 1 RS422/485 1 1 USA, Canada. Check with your local distributor for availability and options. Accessories MDR-20-24 24VDC, 20W, 1 A power supply C5UMB3FBG Category 5E UTP 3 ft/1 m - Beige cable C5UMB10FBL Category 5E 10 ft/3 m - Blue cable Antenna options available Certified for use with these networks: AT&T, T-Mobile, Rogers, Sprint, Verizon Contact B&B Electronics for the latest approvals. I/0 Input/ output 1 Cellular Router - CDMA/HSPA Spectre 3G Series Specifications Interfaces Standard Ethernet 10/100 Mbits USB USB Type A Host Binary I/O 1 input / 1 output SIM 1 SIM Card SIM 2 SIM Card Expansion Port Options Port 1 Ethernet 10/100 RS-232/422/485 Modbus, CNT (I/O) Port 2 RS-232/422/485 Modbus CNT (I/O) I/O CNT 4 Binary inputs, 1 Binary output (2 inputs maybe configured as counters) 2 analog inputs, I Binary output Antenna SMA – 50 Ohm 3G: 2 dBi, penta band, right angle dipole Frequency bands Quad Band UMTS (WCDMA): 850, 900,1900 and 2100 MHz Quad-Band GSM/GPRS/EDGE: 850, 900, 1800,1900 MHz Power Source 10 – 30 VDC 300 mW receive mode Consumption Up to 3.5 W (GPRS transmission) Up to 5.5 W (UMTS/HSDPA transmission) Mechanical Dimensions 42x76x113 mm/1.7x3.0x4.5 in (DIN 35 mm) Enclosure Metal Weight 150 g Environmental Operating Temperature -30 to 60°C Storage Temperature -40 to 85°C VPN Tunneling IPsec, OpenVPN, L2TP – secure encrypted tunnels GRE tunnel – simple tunnel without security measures Networking DHCP – automatic IP addressing in LAN network NAT – IP address and ports translation between inside/outside network Firewall: filtering of addresses, ports, protocols VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address VLAN 802.11Q: virtual LAN QoS: quality of service Dial-in – Communicate via CSD call NTP client, NTP Server: time synchronization PPPoE Bridge – PPP frames encapsulation inside ETH frames Configuration and Diagnostics HTTP server – configuration via web server Telnet – configuration and access to the file system SNMP – router diagnostics, communication with I/O and M-BUS Cellular state signalization LED On-line info on cellular signal status (level, cell, neighbors) SMS info – power on, cellular connection or disconnection SMS control – on/off cellular connection, switch SIM, I/O, etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH – encrypted configuration and access to the file system Additional Functions Linux based: program your own applications NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic saved into memory Approvals / Certifications FCC Part 15, CE EN 550 221B ETS 300 342 immunity EN60747 isolation EN60950 safety; EN 60950-1:06 ed.2 + A11:09 + A1:10 EN 301 511, v9.0.2; EN 301 908-1&2, v3.2.1 ETSI EN 301 489-1 V1.8.1 Service Providers GSM: AT&T, Rogers, T-Mobile. CDMA: Sprint, Verizon 42 mm 76 mm Mechanical diagram 113 mm www.bb-elec.com 35 113 mm WIRELESS Cellular Router - Wi-Fi Spectre 3G-W Series PRODUCT FEATURES • • • • • • The Spectre 3G-W cellular router is a single box solution that provides local M2M network connectivity via its built-in Wi-Fi hotspot, Ethernet 10/100 and I/O ports and connects to the Internet via CDMA and HSPA+ cellular telephone networks. The Spectre 3G-W also creates reliable mobile Ethernet connections. With upload speeds of up to 5.7 Mbps and download speeds of up to 14.4 Mbps, the Spectre 3G-W provides ample bandwidth, even for applications that require video. The standard configuration includes multiple 10/100 Ethernet ports, one USB host port, one binary input/output (I/O) port and dual SIM card holders. The second SIM card holder provides network redundancy, as the router can automatically switch between cellular service providers if one connection fails. Creates a Wi-Fi hotspot for M2M applications Modbus compatible Modular design to fit application requirements Dual SIM Cards for redundant backhaul Up to 5.7 Mbps upload/14.4 Mbps download LINUX platform & advanced networking functions Ordering Information Model Ethernet USB I/0 Rs232 Number 10/100 RT3G-300-W 1 1 1 RT3G-310-W 2 1 1 RT3G-320-W 1 1 1 1 RT3G-330-W 1 1 1 RT3G-340-W 1 1 1 Check with your local distributor for availability and options. Accessories MDR-20-24 24VDC, 20W, 1 A power supply C5UMB3FBG Category 5E UTP 3 ft/1 m - Beige C5UMB10FBL Category 5E 10 ft/3 m - Blue Antenna options available Certified for use with these networks: AT&T, T-Mobile, Rogers, Sprint, Verizon Contact B&B Electronics for the latest approvals. 76 mm 42 mm Users may insert Linux scripts and they can create up to four different configurations for the same router. Examples would include the SMS and binary input configurations. Users may switch from one configuration to another at any time. Mechanical diagram 36 42 mm 113 mm AUX I/0 Input/ output 1 1 USA, Canada. The router supports the creation of VPN tunnels using IPsec, OpenVPN and L2TP. It supports DHCP, NAT, NAT-T, DynDNS, NTP, VRRP, control by SMS, and numerous other functions, as well as additional software like SmartCluster VPN Server and R-SeeNet. A password-protected Web interface allows users to configure and manage the SPECTRE 3G from remote locations. The router can automatically upgrade its configuration and firmware from the operator’s central server, allowing for simultaneous mass reconfiguration of every router on the network. 113 mm RS422/485 Cellular Router - Wi-Fi Spectre 3G-W Series Specifications Interfaces Standard Ethernet 10/100 Mbits USB USB Type A Host Binary I/O 1 input / 1 output SIM 1 SIM Card SIM 2 SIM Card Expansion Port Options Port 1 Ethernet 10/100 RS-232/422/485 Modbus CNT (I/O) Port 2 RS-232/422/485 Modbus CNT (I/O) I/O CNT 4 Binary inputs, 1 Binary output (2 inputs maybe configured as counters) 2 Analog inputs, I Binary output Antenna: Cellular & Wi-Fi SMA – 50 Ohm 3G: 2 dBi, penta band, right angle dipole (2). WiFi: 1.8 dBi right angle dipole (1) Frequency bands Quad Band UMTS (WCDMA): 850, 900,1900 and 2100 MHz+ Quad-Band GSM/GPRS/EDGE: 850, 900, 1800 and 1900 MHz Power Source 10 – 30 VDC 300 mW receive mode Consumption Up to 3.5 W (GPRS transmission) Up to 5.5 W (UMTS/HSDPA transmission) Mechanical Dimensions 42x76x113 mm/1.7x3.0x4.5 in (DIN 35 mm) Enclosure Metal Weight 150 g Environmental Operating Temperature -30 to 60°C Storage Temperature -40 to 85°C Features WIFI Specifications RX Sensitivity TX Output power (802.11 b/g/n) 11b 11g (HT20) 11n (HT20) 11n 11b, 11g, 802.11n 802.11n 2.4 GHz 11Mbps 54Mbps MSC7 MSC7 11Mbps 54Mbps (HT20) (HT20) -85 dBm -70 dBm -66 dBm -62 dBm 19 dBm 16 dBm 15 dBm 15 dBm Frequency band Networking DHCP – automatic IP addressing in LAN network NAT – IP address and ports translation between inside/outside network Firewall: filtering of addresses, ports, protocols VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address VLAN 802.11Q: virtual LAN QoS: quality of service Dial-in – Communicate via CSD call NTP client, NTP Server: time synchronization PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPsec, OpenVPN, L2TP – secure encrypted tunnels GRE tunnel – simple tunnel without security measures Configuration and Diagnostics HTTP server – configuration via web server Telnet – configuration and access to the file system SNMP – router diagnostics, communication with I/O and M-Bus Cellular state signalization by LED On-line info on cellular signal status (level, cell, neighbors) SMS info – power on, cellular connection or disconnection SMS control – on/off cellular connection, switch SIM, I/O, etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH – encrypted configuration and access to the file system Additional Functions Linux based: program your own applications NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic saved into memory Approvals / Certifications FCC Part 15 GGSM: AT&T, Rogers, T-Mobile Certifications CDMA: Sprint, Verizon EN 301 511, v9.0.2 EN 301 908-1&2, v3.2.1 CE ETSI EN 301 489-1 V1.8.1 EN 60950-1:06 ed.2 + A11:09 + A1:10 Emission EN 55022/B Immunity ETS 300 342 Safety EN 60950 Isolation EN 60747 www.bb-elec.com 37 WIRELESS Cellular Router - GPRS/EDGE ER75i v2 Series PRODUCT FEATURES • • • • • • • GPRS/EDGE ER75i v2 router is used to wirelessly connect various equipment and devices via Ethernet interface 10/100 to the Internet or intranet. With a high security level and wide coverage of GPRS/EDGE technology provided by mobile phone operators, it is mostly used in industrial applications, for remote maintenance and service of machines, or for data transfer from solar or wind power plants. Other benefits and advantages includes high modularity and option to connect various devices via Ethernet 10/100, RS232, RS485, RS422, M-Bus or I/O. Key features As a standard, this industrial ER75i v2 wireless router is equipped with one Ethernet 10/100, one USB Host port, one binary input/output (I/O) port and one SIM card. To save and backup communication data, a version with 2 SIM cards is available. The wide range of interface options of this wireless router further expands an optional Port1 and Port2 selected by the customer. For example, Ethernet port 10/100, serial interface ports RS232/RS485/RS422/M-Bus or (I/O - CNT). Port2 may be equipped with serial interfaces RS232/RS485/RS422/M-Bus or (I/O CNT). The wireless router is supplied either in a plastic or metal casing, based on the requirements of the customer. Configuration is done via web interface protected by password. The GPRS/EDGE router supports creation of VPN tunnels using technologies IPsec, OpenVPN and L2TP to ensure safe communication. Web interface provides detail statistics about the wireless router activities, signal strength, detailed log, etc. Router supports functions: DHCP, NAT, NAT-T, DynDNS, NTP, VRRP, control by SMS and many other functions. Other diagnostic functions to ensure continuous communication include automatic inspection of PPP connection offering an automatic restart feature - in case of connection losses, or hardware watchdog which monitors the status of the router. With the help of a special start up script window, you may insert Linux scripts for various actions. For some applications the option to create several different configurations for one wireless GPRS/EDGE router, the profiles (maximum of 4), and the option to switch between them (for example via SMS, binary input status, etc.) is essential. Cellular wireless routers may automatically upgrade configuration and firmware from server. This allows mass reconfiguration of many routers in one time. 38 Designed for M2M applications WiFi, M-BUS and Modbus TCP / Modbus RTU Modular design to fit application requirements Single or Dual SIM Cards for redundant backhaul Up to 85.6 KBps upload/236.8 KBps download LINUX Platform & Advanced Networking Functions ‘C’ based dev environment to build user applications Ordering Information Model Number ER75i v2B Set ETH RS485/ i/o USB SIM RS232 M-Bus i/0 WIFI 10/100 RS422 (CNT) 1 1 1 1 ER75i v2B ETH Set 2 1 1 ER75i v2B RS232 Set ER75i v2B RS485/422 Set ER75i v2B M-Bus Set 1 1 1 1 1 1 1 1 1 ER75i v2B CNT Set 1 1 1 1 ER75i v2F Set 1 1 2 1 ER75i v2F ETH Set 2 1 2 ER75i v2F RS232 Set ER75i v2F RS485/422 Set ER75i v2F M-Bus Set 1 1 2 1 1 2 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ER75i v2F CNT Set 1 1 2 1 ER75i v2F WIFI Set 1 1 2 1 ER75i v2F SWITCH Set 3 1 2 1 SL 1 1 1 Router metal casing (sample ER75i v2B SL) If the optional second port is installed in the Full (F) version, the order code generator will use: the name of the router interface + F + interface of the optional Port 1 + interface of the second optional (Port 2). Example: ER75i v2F ETH RS232 set (supplied UR75i v2 router + 2 x ETH 10/100 + 1 x RS232 + 1 x USB HOST + 2 x SIM, 1 x I/O, accessories) Europe, Middle East, Africa, Asia, South America, Latin America. Check with your local distributor for availability and options. Accessories MDR-40-24 24VDC, 20W, 1 A power supply C5UMB3FBG Category 5E UTP 3 ft/1 m - Beige C5UMB10FBL Category 5E 10 ft/3 m - Blue applications Self-service terminals IT and communication Metrology, alarm and warning systems Energy and power industry Transportation and security Cellular Router - GPRS/EDGE ER75i v2 Series Specifications INTERFACES Standard Ethernet Independent or Bridged USB SIM I/O 2 Optional Ports Port 1 Features Linux based, possibility to program your own application NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic´s saving into memory Networking DHCP – automatic IP addressing in LAN network NAT/PAT – IP address and ports translation between inside/outside network VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address Dial-in – the ability to communicate over dial CSD call PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPsec, OpenVPN, L2TP secure encrypted tunnels GRE tunnel simple tunnel without security measures Configuration and Diagnostic HTTP server – configuration via web server Telnet configuration and access to the file system SNMP router diagnostics, communication with I/O and M-Bus GPRS/EDGE state signalization by LED On-line info on GSM signal status (level, cell, neighbors) SMS info power on, GPRS connection or disconnection SMS control on/off GPRS connection, switch SIM, I/O etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH encrypted configuration and access to the “le system Approvals/Certifications CE EN 301 511, v9.0.2 EN 301 908–1&2, v3.2.1 ETSI EN 301 489–1 V1.8.1 EN 60950–1:06 ed. 2 + A11:09 10/100 Mbits USB 2.0 Host, Type A SIM Card Binary input/output Ethernet (10/100Mbps) RS232 RS422/485 M-Bus I/O Input/Output Port 2 RS232 RS422/485 M-Bus 2nd SIM Card holder Optional Antenna SMA – 50 Ohm Frequency bands GSM 900, 1800 MHz GSM 850, 1900 MHz Quad Band GPRS/EDGE Maximum download 236,8 kb/s Maximum upload 85,6 kb/s Power Source Mechanical 10 – 30 VDC Dimensions 42×76×113 mm (DIN rail 35 mm) Metallic (SL) version - 42x80x113mm Environmental Temperature Range Storage Temperature -30° to +60°C -40° to +85°C Mechanical diagram Dimensions are in mm 107.6 98.3 87.9 78.3 83.1 68.4 71.0 47.8 44.4 41.8 21.2 7.5 0.0 2.4 41.8 (21.0) 17.0 Ø6.6 8.9 76.3 76.3 6.7 0.6 6.7 8.2 8.2 14.3 15.7 107.4 (111.6) 103.0 89.6 94.0 87.5 34.0 36.0 26.4 20.0 24.4 3.1 7.5 (1.6) (21.0) 0.0 0.0 2.6 99.2 www.bb-elec.com 39 WIRELESS Cellular Router - UMTS/HSPA+ & GPRS/EDGE UR5i V2 Libratum Balanced Routers PRODUCT FEATURES • • • • • • Balanced router UR5iv2 Libratum a UMTS/HSPA+, non-modular wireless router features high speed data rates 14.4 Mbps, two Ethernet 10/100 ports and dual-SIM failover capability for mission critical applications. This router is particularly suited to the demands of the “Transaction Management” industry such as point-of-sale terminals, remote ATMs and vending terminals as well as a huge variety of intelligent remote monitoring and control applications in the Transport, Energy and Security sectors. Key features This exceptionally fast UMTS/HSPA+ UR5i v2 Libratum wireless router is equipped with two Ethernet 10/100 ports and two SIM cards. Two SIM cards backup communication in mobile operator network or networks and provide failover to each other. WiFi extension available on demand. Configuration is done via a web interface protected by password. The 3G UMTS/HSPA+ router supports creation of VPN tunnels using IPsec, OpenVPN and L2TP to assure safe communication. Web interface provides detail statistics about the 3G router activities, signal strength, detailed log, etc. Cellular router supports functions: DHCP, NAT, NAT-T, DynDNS, NTP, VRRP, control by SMS and many other functions. Other diagnostic functions for continuous communication include automatic inspection of PPP connection offering an automatic restart feature - in case of connection losses, or hardware watchdog which monitors the status of the router. With the help of a start up script window you may insert Linux scripts for various actions. For some applications the key option is to create several different configurations for one UMTS/HSPA+ wireless router, the so-called profiles (maximum of 4), and the option to switch among them (for example via SMS, binary input status, etc.) is essential. Cellular wireless routers may automatically upgrade configuration and firmware from server. This allows mass reconfiguration of many routers in one time. 40 2-port Ethernet switch 2 independent LAN Models with Wi-Fi: AP or client mode Dual-SIM fail over Antenna Rx Diversity Temperature up to +85°C Ordering Information ETH Plastic Metal SIM i/0 wifi Accessories 10/100 Case Case Model Number UR5i v2 Libratum set UR5i v2 Libratum SL set UR5i v2 Libratum WiFi set UR5i v2 Libratum WiFi SL set 2 2 2 2 1 2 1 1 1 3 1 2 2 1 1 3 3 3 3 3 3 3 Europe, Middle East, Africa, Asia, South America, Latin America. Check with your local distributor for availability and options. Accessories MDR-40-24 24VDC, 20W, 1 A power supply C5UMB3FBG Category 5E UTP 3 ft/1 m - Beige C5UMB10FBL Category 5E 10 ft/ 3m - Blue Selected applications Transportation and security IT and communication Self-service terminals Energy and power industry Meteorology, alarm and warning systems Cellular Router - UMTS/HSPA+ & GPRS/EDGE UR5i V2 Libratum Balanced Routers Specifications INTERFACES Standard Ethernet 2x independent 10/100 Mbits or bridged SIM 1 SIM Card SIM 2 SIM Card Antenna connectors SMA – 50 Ohm Frequency bands Quad Band HSPA+ 850/900/1900/2100 MHz Quad Band GSM 850/900/1800/1900 MHz HSPA+ parameters Bit rate 14.4 Mbps / 5,76 Mbps 3GPP rel. 6/7 standard Data compress 3GPP UMTS parameters Download – 384 kbps Upload – 384 kbps 3GPP rel. 6/7 standard EDGE/GPRS parameters Bit rate EDGE 237 kbps / 237 kbps Bit rate GPRS 85,6 kbps / 85,6 kbps Multislot class 12, CS 1 to 4, 3GPP rel. 99/4 standard WiFi 802.11b, 802.11g, 802.11n Security - 64/128 WEP, TKIP, AES Authentication - Shared, WPA-PSK, WPA2-PSK Power Source 10 – 30 VDC Mechanical Plastic version - 50x83x116mm Dimension Metallic (SL) version - 42x80x113mm Environmental Temperature range -30° to +85°C Storage Temperature -40° to +85°C Features DHCP – automatic IP addressing in LAN network NAT – IP address and ports translation between inside/outside network Firewall: filtering of addresses, ports, protocols VRRP – virtual backup router function DynDNS client – access to the router with a dynamic Networking IP address VLAN 802.11Q: virtual LAN QoS: quality of service Dial-in – Communicate via CSD call NTP client, NTP Server: time synchronization PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPSec, Pre-Shared key, Username/Password, X.509, Initiator - Responder (DES, 3DES, AES, MD5, SHA-1, DH-2,5,14-18) OpenVPN, Pre-Shared key, Username/Password, X.509, Server/Client/Multiclient (BF-CBC, AES128, DES3DES) L2TP, PPTP, simple tunnel with Username/Password auth. EasyVPN, simple tunnel with Username/Password auth. GRE, simple tunnel without security measures Diagnostic Status Network all information about active interface Status DHCP status of DHCP server Status UMTS/GPRS mobile network information, statistic Status IPSec status of IPSec System Log list of system messages SNMP traps with R-SeeNET Approvals/Certifications EN 301 511, v9.0.2 EN 301 908-1&2, v3.2.1 CE ETSI EN 301 489-1 V1.8.1 EN 60950-1:06 ed.2 + A11:09 + A1:10 www.bb-elec.com 41 WIRELESS Cellular Router - 3G UMTS/HSPA+ UR5i v2 Series PRODUCT FEATURES • • • • • • • 3G UMTS/HSPA routers, UR5i v2 series, are used to wirelessly connect various equipment and devices via Ethernet 10/100 to the Internet or intranet. High data transfer speed of up to 21.1 Mbit/s (download) and upload speed up to 5.7 Mbit/s, make it an ideal wireless solution for traffic and security camera systems, individual computers, LAN networks, automatic teller machines (ATM) and other self-service terminals, etc. Key features This exceptionally fast 3G UR5i v2 wireless router is equipped with one Ethernet 10/100, one USB Host port, one binary Input/Output (I/O) port and one SIM card. To save and backup communication data, a version with 2 x SIM cards is available. A wide range of user-defined interface options further expands optional Port1 and Port2. (EX: Ethernet port 10/100, serial interface ports RS232/RS485/RS422/M-Bus or (I/O - CNT). Port2 may be equipped with serial interfaces RS232/RS485/RS422/M-Bus or (I/O - CNT). This 3G wireless router is available in a plastic or metal casing. Configuration is done via web interface protected by password. The 3G UMTS/HSPA+ router supports creation of VPN tunnels using IPsec, OpenVPN and L2TP to ensure safe communication. Web interface provides detail statistics about router activities, signal strength, detailed log, etc. Cellular router supports functions: DHCP, NAT, NAT-T, DynDNS, NTP, VRRP, control by SMS and many other functions. Other diagnostic functions ensuring continuous communication include automatic inspection of PPP connection offering an automatic restart feature in case of connection losses, and hardware watchdog which monitors the status of the router. With the help of a start up script window you may insert Linux scripts for various actions and, for some applications the option to create several different configurations for one 3G wireless router, profiles (maximum of 4), and the option to switch between them (for example via SMS, binary input status, etc.). Cellular wireless routers can automatically upgrade configuration and firmware from server. This allows mass reconfiguration of multiple routers at one time. 42 Designed for M2M applications WiFi, M-BUS and Modbus TCP / Modbus RTU Modular design to fit application requirements Single or dual SIM cards for redundant backhaul Up to 5.7 Mbps upload to 21.1 Mbps download LINUX platform & advanced networking functions ‘C’ based dev environment to build user applications Ordering Information Model Number UR5i v2B Set ETH RS485/ i/o USB SIM RS232 M-Bus i/0 WIFI 10/100 RS422 (CNT) 1 1 1 1 UR5i v2B ETH Set 2 1 1 UR5i v2B RS232 Set 1 1 1 UR5i v2B RS485/422 Set 1 1 1 UR5i v2B M-Bus Set 1 1 1 UR5i v2B CNT Set 1 1 1 1 UR5i v2F Set 1 1 2 1 UR5i v2F ETH Set 2 1 2 UR5i v2F RS232 Set 1 1 2 UR5i v2F RS485/422 Set 1 1 2 UR5i v2F M-Bus Set 1 1 2 UR5i v2F CNT Set 1 1 2 1 UR5i v2F WIFI Set 1 1 2 1 UR5i v2F SWITCH Set 3 1 2 1 SL 1 1 1 1 1 1 1 1 1 1 1 1 1 Router metal casing (sample ER75i v2B SL) Europe, Middle East, Africa, Asia, South America, Latin America. Check with your local distributor for availability and options. Accessories MDR-40-24 24VDC, 20W, 1 A power supply C5UMB3FBG Category 5E UTP 3 f/1 m - Beige C5UMB10FBL Category 5E 10 ft/ 3 m - Blue Selected applications Transportation and security IT and communication Self-service terminals Energy and power industry Metrology, alarm and warning systems 1 1 1 1 Cellular Router - 3G UMTS/HSPA+ UR5i v2 Series Specifications INTERFACES Standard Ethernet Independent 10/100 Mbits or Bridged SIM SIM Card I/O Binary input/output USB USB 2.0 Host, Type A 2 Optional Ports Port 1 Ethernet (10/100Mbps) RS232 RS422/485 M-Bus I/O Input/Output Port 2 RS232 RS422/485 M-Bus Optional 2nd SIM Card holder Antenna connectors SMA – 50 Ohm Frequency bands Quad Band UMTS (WCDMA): 850, 900, 1900 and 2100 MHz Quad-Band GSM/GPRS/EDGE: 850, 900, 1800, 1900 MHz HSPA+ parameters Bit rate 14.4 Mbps / 5,76 Mbps 3GPP rel. 6/7 standard Data compress 3GPP UMTS parameters Download – 384 kbps Upload – 384 kbps 3GPP rel. 6/7 standard EDGE/GPRS parameters Bit rate EDGE 237 kbps / 237 kbps Bit rate GPRS 85,6 kbps / 85,6 kbps Multislot class 12, CS 1 to 4, 3GPP rel. 99/4 standard POWER Source 10 – 30 VDC Environmental Temperature range -30° to +60°C Storage Temperature -40° to +85°C Dimension 42×76×113 mm (DIN rail 35 mm) Metallic (SL) version - 42x80x113mm Features Linux based, possibility to program your own application NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic´s saving into memory Networking DHCP – automatic IP addressing in LAN network NAT/PAT – IP address and ports translation between inside/outside network VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address Dial-in – the ability to communicate over dial CSD call PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPsec, OpenVPN, L2TP – secure encrypted tunnels GRE tunnel – simple tunnel without security measures Configuration and Diagnostic HTTP server – configuration via web server Telnet – configuration and access to the file system SNMP – router diagnostics, communication with I/O and M-BUS GPRS state signalization by LED On-line info on GSM signal status (level, cell, neighbors) SMS info – power on, GPRS connection or disconnection SMS control – on/off GPRS connection, switch SIM, I/O etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH – encrypted configuration and access to the #le system Approvals/Certifications EN 301 511, v9.0.2 EN 301 908–1&2, v3.2.1 CE ETSI EN 301 489–1 V1.8.1 EN 60950–1:06 ed. 2 + A11:09 Mechanical diagram Dimensions are in mm 99.3 107.6 83.2 73.7 72.2 60.3 67.0 69.6 49.0 50.3 43.6 41.4 (21.0) 44.0 33.6 20.2 26.9 20.7 0.0 2.4 7.5 10.7 41.8 17.0 76.3 0.6 6.7 8.2 8.2 14.3 15.7 17.0 (111.6) 107.4 89.6 87.5 34.0 36.0 24.4 26.4 3.1 (1.6) (21.0) 99.2 0.0 0.0 76.3 8.9 8.9 2.6 www.bb-elec.com 43 WIRELESS Cellular Router - 4G LTE LR77 v2 Series PRODUCT FEATURES • • • • • • • 4G LTE router LR77 v2 provides wireless connection of equipment and devices via Ethernet 10/100 or serial interfaces to the Internet or intranet. 4G router LR77 v2 is ideal for transferring large data loads. With LTE its ultra fast data transfer speed reaches up to 100 Mbit/s download and up to 50 Mbit/s upload. The LR77 v2 series is an ideal wireless solution for traffic and security camera systems, individual computers, LAN networks, automatic teller machines (ATM) and other self-service terminals, etc. This extra fast 4G LR77 v2 wireless router is equipped with one Ethernet 10/100, one USB Host port, one binary Input/output (I/O) port and one SIM card. To save and backup communication data, a version with 2 x SIM cards is available. A wide range of user-defined interface options further expands optional Port1 and Port2. Port1 is available as an Ethernet port 10/100, serial interface ports RS232/RS485/RS422/M-Bus or (I/O - CNT). Port2 may be equipped with serial interfaces RS232/RS485/RS422/M-Bus or (I/O - CNT). Another option is inserting a XC-SW board to provide 3 x switched Ethernet 10/100 ports. This router is available either in a plastic or metal casing. Configuration is done via web interface protected by password. The 4G LTE router supports creation of VPN tunnels using IPsec, OpenVPN and L2TP to ensure safe communications. Web interface provides detailed statistics about router activities, signal strength, detailed log, etc. Supports functions: DHCP, NAT, NAT-T, DynDNS, NTP, VRRP, HTTPS, SSH, OSPF, RIP, BGP control by SMS and many other functions. Other diagnostic functions to ensure continuous communication include automatic inspection of PPP connection with an automatic restart feature in case of connection losses and a hardware watchdog which monitors the status of the router. With the help of a start up script window you may insert Linux scripts for various actions. For some applications it is possible to create several different configurations or profiles for router (maximum of 4), and the option to switch between them (for example via SMS, binary input status, etc.). Cellular LTE wireless router LR77 v2 supports automatic upgrade of configuration and firmware from the server. This allows mass reconfiguration of multiple routers in one time. It is also possible to develop user defined modules that modify LTE router behavior. 44 Designed for M2M applications WiFi, M-BUS and Modbus TCP / Modbus RTU Modular design to fit application requirements Single or dual SIM cards for redundant backhaul LTE Up to 50 Mbps upload to 100 Mbps download LINUX platform & advanced networking functions ‘C’ based dev environment to build user applications Ordering Information Model Number ETH RS485/ i/o USB SIM RS232 M-Bus i/0 WIFI 10/100 RS422 (CNT) 1 1 1 1 2 1 1 1 1 1 1 1 1 LR77 v2B Set LR77 v2B ETH Set LR77 v2B RS232 Set LR77 v2B RS485/422 1 1 1 1 Set LR77 v2B M-Bus Set 1 1 1 1 LR77 v2B CNT Set 1 1 1 LR77 v2F Set 2 1 2 LR77 v2F RS232 Set 1 1 2 1 LR77 v2F RS485/422 1 1 2 1 Set LR77 v2F M-Bus Set 1 1 2 1 LR77 v2F CNT Set 1 1 2 LR77 v2F SWITCH Set 3 1 2 LR77 v2F WIFI Set 1 1 2 LR77 v2F SWITCH Set 3 1 2 SL Router metal enclosure (sample LR77 v2B SL) Europe, Middle East, Africa, Asia, South America, Latin America. Check with your local distributor for availability and options. Accessories MDR-40-24 24VDC, 20W, 1 A power supply C5UMB3FBG Category 5E UTP 3 ft/ 1m - Beige C5UMB10FBL Category 5E 10 ft/3 m - Blue applications Transportation and security IT and communication Self-service terminals Energy and power industry Metrology, alarm and warning systems 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Cellular Router - 4G LTE LR77 v2 Series Specifications INTERFACES Standard Ethernet Independent 10/100 Mbits or Bridged SIM SIM Card I/O Binary input/output USB USB 2.0 Host, Type A 2 Optional Ports Port 1 Ethernet (10/100Mbps) RS232 RS422/485 M-Bus I/O Input/Output Ethernet Switch (with port 2) Port 2 RS232 RS422/485 M-Bus WM-Bus SDH WiFi Ethernet Switch (with port 1) Optional 2nd SIM Card holder Antenna connectors SMA – 50 Ohm Frequency bands GSM/GPRS/EDGE: 900/1800/1900 MHz UMTS/HSDPA/HSUPA/HSPA+: 900/2100 MHz LTE: 800/900/1800/2100/2600 MHz LTE Maximum download 100 Mbps Maximum upload 50 Mbps POWER Source 10 – 30 VDC Consumption Reception 2.3 W GPRS to 3.5 W (GPRS transmission) LTE to 5.5 W (LTE transmission) Environmental Temperature Range -30° to +60°C Storage Temperature -40° to +85°C Dimension 42×76×113 mm (DIN rail 35 mm) Metallic (SL) version - 42x80x113 mm Weight LR77 v2 – 150 g LR77 v2 SL – 280 g LTE parameters Bit rate 100 Mbps (DL) / 50 Mbps (UL) 3GPP rel. 8 standard Supported bandwidth: 5 Mhz, 10 Mhz, 20 Mhz HSPA+ parameters Bit rate 21,1 Mbps (DL) / 5,76 Mbps (UL) 3GPP rel. 7 standard UE CAT. 1 to 6, 8, 10, 12, 14 3GPP data compress UMTS parameters PS bit rate 384 kbps (DL) / 384 kbps (UL) CS bit rate 64 kbps (DL) / 64 kbps (UL) W-CDMA FDD standard GPRS/EDGE parameters Bit rate 237 kbps (DL) / 59,2 kbps (UL) GPRS multislot class 10, CS 1 to 4 EDGE multislot class 12, CS 1 to 4 MCS 1 to 9 Supported GPRS/EDGE power classes EGSM 900: Class 4 (33 dBm) GSM 1800/1900: Class 1 (30 dBm) EDGE 900: Class E2 (27 dBm) EDGE 1800/1900: Class E2 (26 dBm) Features Linux based, possibility to program your own application NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic´s saving into memory Networking DHCP – automatic IP addressing in LAN network NAT/PAT – IP address and ports translation between inside/outside network VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address Dial-in – the ability to communicate over dial CSD call PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPsec, OpenVPN, L2TP – secure encrypted tunnels Configuration and Diagnostic HTTP server – configuration via web server Telnet – configuration and access to the file system SNMP – router diagnostics, communication with I/O and M-Bus GPRS state signalization by LED On-line info on GSM signal status (level, cell, neighbors) SMS info – power on, GPRS connection or disconnection SMS control – on/off GPRS connection, switch SIM, I/O etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH – encrypted configuration and access to the file system Approvals/Certifications EN 301 511, v9.0.2, EN 301 908-1 & -2: v3.2.1, CE ETSI EN 301 489-1 V1.8.1, EN 60950-1:06 ed.2 + A11:09 + A1:10 www.bb-elec.com 45 WIRELESS Cellular Router - CDMA CR10 v2 Series PRODUCT FEATURES • • • • • • CDMA router CR10 v2 provides wireless connection of equipment and devices via Ethernet 10/100 or serial interfaces to the Internet or intranet. CDMA router CR10 v2 is perfect for transferring large data loads. Its fast data transfer speed reaches up to 3.1 Mbit/s download and up to 1.8 Mbit/s upload. CDMA technology makes it an ideal wireless solution for data transfer from traffic and security camera systems, individual computers, LAN networks, automatic teller machines (ATM) and other selfservice terminals, etc. CDMA router CR10 v2 is equipped with one Ethernet 10/100, one USB Host port, one binary Input/output (I/O) port and one SIM card. A wide range of user-defined interface options can expand optional Port1 and Port2. Port1 is available as Ethernet port 10/100, serial interface ports RS232/RS485/ RS422/M-Bus or (I/O - CNT). Port2 may be equipped with serial interfaces RS232/RS485/RS422/M-Bus or (I/O - CNT). Another option is inserting an XC-SW board to provide 3 x switched Ethernet 10/100 ports. CDMA wireless routers are available in either in a plastic or metal casing. Configuration is done via password protected web interface. It supports creation of VPN tunnels with IPsec, OpenVPN and L2TP to ensure safe communications. Web interface provides detailed statistics of router activities, signal strength, detailed log, etc. Supports functions: DHCP, NAT, NAT-T, DynDNS, NTP, VRRP, HTTPS, SSH, OSPF, RIP, BGP and many more. Other diagnostic functions to ensure continuous communications include automatic inspection of PPP connection with an automatic restart feature in case of connection losses, hardware watchdog that monitors router status. With the help of a start-up script window, you can insert Linux scripts for various actions. It is also possible to create different configurations or profiles for one CDMA wireless router (maximum of 4), and the option to switch between them (for example via binary input status, etc.). Or, develop user-defined modules to modify CDMA router behavior. The router supports automatic upgrade of configuration and firmware from server allowing mass reconfiguration of multiple routers at one time. 46 SMS and E-mail functions Up to 3.1 Mbps download and 1.8 Mbps upload WiFi, M-BUS and Modbus TCP / Modbus RTU Modular design to fit application requirements Single or dual SIM cards for redundant backhaul LINUX platform & advanced networking functions Ordering Information Model Number ETH RS485/ i/o USB SIM RS232 M-Bus i/0 WIFI 10/100 RS422 (CNT) CR10 v2B Set 1 1 1 1 CR10 v2B ETH Set 2 1 1 1 CR10 v2B RS232 Set 1 1 1 1 1 CR10 v2B RS485/422 Set 1 1 1 1 1 CR10 v2B M-Bus Set 1 1 1 1 1 CR10 v2B CNT Set 1 1 1 1 1 CR10 v2F Set 1 1 2 1 CR10 v2F ETH Set 2 1 2 1 CR10 v2F RS232 Set 1 1 2 1 1 CR10 v2F RS485/422 Set 1 1 2 1 1 CR10 v2F M-Bus Set 1 1 2 1 1 CR10 v2F CNT Set 1 1 2 1 1 CR10 v2F WIFI Set 1 1 2 1 CR10 v2F SWITCH Set 3 1 2 1 SL Router metal enclosure (Example: CR10 v2B SL) Europe, Middle East, Africa, Asia, South America, Latin America. Check with your local distributor for availability and options. Accessories MDR-40-24 24VDC, 20W, 1 A power supply C5UMB3FBG Category 5E UTP 3 ft/1 m - Beige C5UMB10FBL Category 5E 10 ft/3 m - Blue applications Energy and power industry Self-service terminals Transportation and security IT and communication Metrology, alarm and warning systems 1 Cellular Router - CDMA CR10 v2 Series Specifications INTERFACES Standard Ethernet Independent 10/100 Mbits or Bridged SIM SIM Card I/O Binary input/output USB USB 2.0 Host, Type A 2 Optional Ports Port 1 Ethernet (10/100Mbps) RS232 RS422/485 M-Bus I/O Input/Output Ethernet Switch (with port 2) Port 2 RS232 RS422/485 M-Bus WM-BUS SDH WiFi Ethernet Switch (with port 1) Optional 2nd SIM Card holder Antenna connectors SMA – 50 Ohm CDMA Parameters Rev. A: Bit rate 3.1 Mbps (DL) / 1.8 Mbps (UL) Rev. B: Bit rate 14.7 Mbps (DL) / 5.4 Mbps (UL) Backward compatible with Rev.0 Transmit power +23.0 dBm 47 to 30.0 dBm Supported bands 450 MHz (Sub band A,B,L) POWER Source 10 – 30 VDC Consumption Reception 2.6 W CDMA to 4 W Environmental Temperature Range -30° to +60°C Storage Temperature -40° to 85°C Dimensions 42×76×113 mm (DIN rail 35 mm) Metallic (SL) version - 42x80x113mm Weight 280 g Features Linux based, possibility to program your own application NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic´s saving into memory Networking DHCP – automatic IP addressing in LAN network NAT/PAT – IP address and ports translation between inside/outside network VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address Dial-in – the ability to communicate over dial CSD call PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPsec, OpenVPN, L2TP – secure encrypted tunnels Configuration and Diagnostic HTTP server – configuration via web server Telnet – configuration and access to the file system SNMP – router diagnostics, communication with I/O and M-Bus GPRS state signalization by LED On-line info on GSM signal status (level, cell, neighbors) SMS info – power on, GPRS connection or disconnection SMS control – on/off GPRS connection, switch SIM, I/O, etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH – encrypted configuration and access to the file system Approvals/Certifications EN 301 511, v9.0.2, EN 301 908-1 & -2: v3.2.1, CE ETSI EN 301 489-1 V1.8.1, EN 60950-1:06 ed.2 + A11:09 + A1:10 www.bb-elec.com 47 WIRELESS UMTS/CDMA Router UCR11 v2 Series PRODUCT FEATURES • • • • • • • The UCR11 v2 is wireless UMTS/CDMA router provides the exceptional modularity in mobile wireless network environments. The router may be equipped with 2 independent RF modules (UMTS, CDMA). You can select between CDMA 450 MHz and 3G UMTS) technology. CDMA 400 MHz is backed up by UMTS and vice versa to eliminate downtime. The redundancy of the UMTS/CDMA Router UCR11 v2 is particularly suited to industrial applications. The router features high speed data rates 21.1 Mbps, one Ethernet 10/100 port and dual-SIM failover capability for mission critical applications. it is particularly suited to the demands “Transaction Management” applications such as point-of-sale terminals, remote ATMs and vending terminals as well as a variety of intelligent remote monitoring and control applications in the Transport, Energy and Security sectors. Other benefits and advantages includes high modularity - the router connection of various user devices via Ethernet 10/100, RS-232, RS-485, RS-422, MBUS, WiFi or I/O. This exceptionally fast UMTS/CDMA wireless router is equipped with one Ethernet 10/100, one USB host port, one binary Input/ output (I/O) port and two SIM card slots to save and backup communication data. A wide range of interface options further expands optional Port1 and Port2 - selected by the customer. Optional Port 1 can be defined as Ethernet port 10/100 or serial interface ports RS232 or RS-485/RS-422 or MBUS or I/O - CNT. Port2 may be equipped with serial interfaces RS-232 or RS-485/ RS-422 or MBUS or I/O – CNT or WiFi. Another option is inserting an XC-SW board to provide 3 x switched Ethernet 10/100 ports. 48 UMTS and CDMA in one router Up to 21.1 Mbps download and 5.76 Mbps upload Single or dual SIM cards for redundant backhaul Modular design to fit application requirements LINUX platform & advanced networking functions WiFi, M-BUS and WM-BUS SMS and Email Ordering Information Model Number UMTS Router UCR11 v2F-01 SL set Poland-Orange UCR11 v2F-02 SL set Poland-Plus UCR11 v2F-03 SL set Czech Republic Telefónica UCR11 v2F-04 SL set Germany - INET UCR11 v2F-05 SL set Sweden - NET1 UCR11 v2F-06 SL set Norway - NET1 UCR11 v2F-07 SL set Russia - SkyLink ETH 10/100 USB SIM Port i/0 UMTS Signal 2 2 1 1 2 2 2 2 1 1 a a 2 1 2 2 1 a 2 2 2 2 1 1 1 1 2 2 2 2 2 2 2 2 1 1 1 1 a a a a Ordering Information Model Number CDMA Router UCR11 v2F-01D SL set Poland-Orange UCR11 v2F-02D SL set Poland-Plus UCR11 v2F-03D SL set Czech Republic Telefónica UCR11 v2F-04D SL set Germany - INET UCR11 v2F-05D SL set Sweden - NET1 UCR11 v2F-06D SL set Norway - NET1 UCR11 v2F-07D SL set Russia - SkyLink ETH 10/100 USB SIM Port i/0 CDMA Signal 2 2 1 1 2 2 2 2 1 1 a a 2 1 2 2 1 a 2 2 2 2 1 1 1 1 2 2 2 2 2 2 2 2 1 1 1 1 a a a a Europe, Middle East, Africa, Asia, South America, Latin America. Check with your local distributor for availability and options. Accessories MDR-40-24 - 24VDC, 20W, 1 A power supply C5UMB3FBG - Category 5E UTP 3 ft/1 m - Beige C5UMB10FBL - Category 5E 10 ft/3 m - Blue applications Transportation and security IT and communication Self-service ATM, Gaming terminals Industry -SCADA and Remote Management Energy and power industry Meteorology, alarm and warning systems UMTS/CDMA Router UCR11 v2 Series Specifications User Interface Standard Ethernet Independent or Bridged SIM I/O USB 2 Optional Ports Port 1 10/100 Mbits 2 SIM slots Binary input/output USB 2.0 Host, Type A Ethernet (10/100Mbps) RS232 RS422/485 M-Bus I/O Input/Output Port 2 RS232 RS422/485 M-Bus I/O Input/Output Antenna connectors SMA – 50 Ohm UMTS Module UMTS/HSPA+ Maximum download 14.4 Mbps Maximum upload 5.7 Mbps Bit rate 21.1 Mbps (DL) / 5.76 Mbps (UL) 3GPP rel. 7 standard HSPA+ parameters UE CAT. 1 to 6, 8, 10, 12, 14 3GPP data compress PS bit rate 384 kbps (DL) / 384 kbps (UL) UMTS parameters CS bit rate 64 kbps (DL) / 64 kbps (UL) W-CDMA FDD standard Bit rate 237 kbps (DL) / 59.2 kbps (UL) multislot class 10, CS 1 to 4 GPRS/EDGE parameters GPRS EDGE multislot class 12, CS 1 to 4 MCS 1 to 9 GSM/GPRS/EDGE: 850/900/1800/1900 MHz Supported channels UMTS/HSDPA/HSUPA/HSPA+: 850/900/1900/2100 MHz CDMA Module Rev. A: Bit rate 3.1 Mbps (DL) / 1.8 Mbps (UL) CDMA parameters Rev. B: Bit rate 14.7 Mbps (DL) / 5.4 Mbps (UL) Backward compatible with Rev.0 Transmit power +23.0 dBm to 30.0 dBm Supported bands 450 MHz (Sub band A,B,L) POWER Source 10 – 30 VDC Reception 2.6W Consumption CDMA to 4.0W UMTS 5.5W Environmental Temperature range Storage temperature Mechanical Dimension -30°C to +60°C -40°C to +85°C Metallic - 42x80x113mm (DIN rail 35 mm) Linux based, possibility to program your own application NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic´s saving into memory Email warnings or critical information Networking DHCP – automatic IP addressing in LAN network NAT/PAT – IP address and ports translation between inside/outside network VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPsec, OpenVPN, L2TP – secure encrypted tunnels GRE tunnel – simple tunnel without security measures Configuration and Diagnostic HTTP server – configuration via web server Telnet – configuration and access to the file system SNMP – router diagnostics, communication with I/O and M-BUS GPRS state signalization by LED On-line info on GSM signal status (level, cell, neighbors) SMS info – power on, GPRS connection or disconnection SMS control – on/o! GPRS connection, switch SIM, I/O etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH – encrypted configuration and access to the file system Standards CE EN 301 511, v9.0.2 EN 301 908-1 & -2: v3.2.1 ETSI EN 301 489-1 V1.8.1 EN 60950-1:06 ed.2 + A11:09 + A1:10 www.bb-elec.com 49 WIRELESS Industrial Router XR5i v2 Series PRODUCT FEATURES • • • • • The XR5i v2 industrial router secures connections between two local networks (LAN) via two Ethernet interfaces 10/100. The XR5i v2 can also convert serial RS232, RS485, M-BUS, I/O to IP local area network (LAN Ethernet 10/100). The XR5i v2 Industrial router will also connect two devices with different serial interfaces (RS232, RS485, M-Bus, I/O, etc.) to the local network. In this configuration, the communication device has an Ethernet 10/100 port and two serial interfaces which user definable. A third option uses combination of two previous versions, when the industrial XR5i v2 router equipped with two Ethernet interfaces 10/100 and one optional serial interface. Standard on the XR5i v2 Industrial Router is one Ethernet 10/100 port, one USB A (host) port, I/O port and two optional interfaces. Users can select a second Ethernet port, 10/100, serial interface RS232/RS485/RS422/MBUS or other Inputs/Outputs (I/O). Industrial XR5i v2 router can be ordered with either a plastic or metal housing. Configuration is password protected, via web interface. The router supports creation of VPN tunnels using IPsec, OpenVPN and L2TP to ensure safe communication. Web interface provides detail statistics about router activities. Modular design to fit application requirements Provided secure connection between two networks Provides USB, Serial and I/O connectivity Configuration with password protected web interface SNMP protocol for remote management Ordering Information Model Number XR5i v2F ETH XR5i v2F RS232 XR5i v2F RS485 XR5i v2F MBUS XR5i v2F CNT XR5i v2F ETH RS232 XR5i v2F RS232 RS485 XR5i v2F ETH MBUS XR5i v2F ETH CNT XR5i v2F RS232 MBUS XR5i v2F WiFi SET SL ETH 10/100 USB RS232 RS485 Mbus 2 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 2 1 1 2 1 1 1 1 1 1 1 Metal casing (Example: XR5i v2F ETH SL) Europe, Middle East, Africa, Asia, South America, Latin America. Check with your local distributor for availability and options. Accessories MDR-40-24 - 24VDC, 20W, 1 A power supply C5UMB3FBG - Category 5E UTP 3 ft/1 m - Beige C5UMB10FBL - Category 5E 10 ft/3 m - Blue applications Industry Self-service terminals IT and communication Energy and power industry Communication 50 i/0 1 1 1 1 1 1 1 1 1 1 1 CNT WiFi 1 1 1 Industrial Router XR5i v2Series Specifications User Interface Standard Ethernet Serial USB I/O 2 Optional Ports Port 1 Port 2 POWER Source Consumption Environmental Temperature range Storage Temperature Mechanical Dimension 10/100 Mbits RS232 USB 2.0 Host, Type A I/O Input/Output Binary Input/Output Ethernet (10/100Mbps) RS232 RS422/485 M-Bus I/O Input/Output (CNT) RS232 RS422/485 M-Bus SHD WI FI WM-BUS 10 – 30 VDC Without Communications 1.6W With Communications 5.5W -30 to +60°C -40 to +85°C 42 x 76 x 113 mm (DIN rail 35 mm) Features Linux based, possibility to program your own application NTP client, NTP Server – time synchronization SMS communication – AT commands on RS232, Ethernet and I/O M-RAM memory inside – router statistic´s saving into memory Email warnings or critical information Networking DHCP – automatic IP addressing in LAN network NAT/PAT – IP address and ports translation between inside/outside network VRRP – virtual backup router function DynDNS client – access to the router with a dynamic IP address PPPoE Bridge – PPP frames encapsulation inside ETH frames VPN Tunneling IPsec, OpenVPN, L2TP – secure encrypted tunnels GRE tunnel – simple tunnel without security measures Configuration and Diagnostic HTTP server – configuration via web server Telnet – configuration and access to the file system SNMP – router diagnostics, communication with I/O and M-BUS GPRS state signalization by LED On-line info on GSM signal status (level, cell, neighbors) SMS info – power on, GPRS connection or disconnection SMS control – on/off GPRS connection, switch SIM, I/O etc. Transferred data counting, one more APN as backup Remote router group configuration change, switching among configuration profiles SSH – encrypted configuration and access to the file system Standards CE ETSI EN 301 489-1 V1.8.1, EN 60950-1:06 ed.2 + A11:09 + A1:10 www.bb-elec.com 51 WIRELESS IP67 Outdoor Rated Industrial Wireless I/O Zlinx Xtreme Wireless I/O PRODUCT FEATURES • • • • • • • • • • • Do you need to monitor remote assets via discrete analog and digital sensors? Or do you need to control remote control equipment from a central SCADA/PLC? Is the remote equipment outdoor? Zlinx Xtreme I/Os can do the job faster, easier and less expensively than stringing cable. These compact and rugged IP67 units are ideal for outdoor applications in extreme weather conditions for connecting remote I/Os to local I/Os wirelessly (via Peer-to-Peer Mode) or to connect remote I/ Os in multiple locations to a central PLC or SCADA or HMI system via a Serial Radio Modem (Via Modbus mode). Zlinx Industrial Wireless products operate in license-free, Proprietary RF 900 MHz and 2.4 GHz ISM bands. Select the 900 MHz version for longer distances. For further flexibility, the output power is software selectable. The 900 MHz units offer 256 bit AES Encryption. The 2.4 GHz have 128 bit AES Encryption. ® IP67 rated for outdoor applications Flexible configuration for multiple types of analog/digital I/Os Modbus compatible Range to 40 miles (64 km) Line of Sight & External Antenna Heavy-duty machine mount industrial grade case and components Signal strength indicator aids trouble shooting 900 MHz and 2.4 GHz versions Wide operating temperature range -40° to 74°C Versatile power 10- 30 VDC AES Encryption UL, Class1/Division2 Ordering Information Model Number Description Zlinx Xtreme Wireless I/O ZXT24-IO-222R2 2.4 GHz * ZXT9-IO-222R2 900 MHz * Analog Inputs Analog Outputs Digital Inputs Digital Relay Outputs 2 2 2 2 2 2 2 2 World-wide. Check with your local distributor for availability and options. * Check wireless regulations/standards in your geographic area. Ordering Information Model Number Description Zlinx Xtreme Wirless I/O Kit Zlinx Xtreme IP67 Peer-to-Peer I/O Kit: 2 - ZXT9-IO-222R2 (I/O Modules), ZXT9-IOA-KIT 2 - CLG-60-24 (Power Supply). 1 - USBAMBM-6F (Program Cable) Zlinx Xtreme IP67 Modbus I/O Kit: 1 - ZXT9-RM (Radio Modem), ZXT9-MB1A-KIT 1 - ZXT9-IO-222R2 (I/O Module), 2 - CLG-60-24 (Power Supply), 1 - USBAMBM-6F (Program Cable) Zlinx Xtreme IP67 Modbus I/O Kit: 1 - ZXT9-RM (Radio Modem), ZXT9-MB2A-KIT 2 - ZXT9-IO-222R2 (I/O Module), 3 - CLG-60-24 (Power Supply), 1 - USBAMBM-6F (Program Cable) Accessories 52 CLG-60-24 P67 Power Supply, Panel Mount, 24VDC, 60 W ZXT9-ANT 900 MHz Spare Antenna ZZ24D-ANT1 2.4 GHz Spare Antenna ZXTMT Conduit Mounting Kit IP67 Outdoor Rated Industrial Wireless I/O Zlinx Xtreme Wireless I/O Specifications RF Properties Physical Standard 802.15.4 Frequency ZXT9-IO-xxxx 900 MHz ISM (902-928 MHz) ZXT24-IO-xxxx 2.4 GHz ISM (2.4 to 2.5 GHz) Transmit Power 1 mW, 10 mW, 100 mW, 500 mW ZXT9-IO-xxxx 1 W – Software Selectable 10 mW, 16 mW, 25 mW, 30 mW ZXT24-IO-xxxx 63 mW – Software Selectable Receiver Sensitivity ZXT9-IO-xxxx -100 dBm ZXT24-IO-xxxx -105 dBm Over the Air Data Rate 9.6 or 115.2 kbps ZXT9-IO-xxxx Software Selectable ZXT24-IO-xxxx 250 kbps Outdoor Range Supplied Antenna 14 mi (23 km) ZXT9-IO-xxxx High Gain Antenna 40 mi (64 km) Supplied Antenna 1.5 mi (2.4 km) ZXT24-IO-xxxx High Gain Antenna 10 mi (16 km) Range estimates based on optimal RF conditions and an unobstructed line of sight. Transmission Method ZXT9-IO-xxxx FHSS ZXT24-IO-xxxx DSSS Modulation FSK Channel Capacity ZXT9-IO-xxxx 10 hop sequences share 50 frequencies ZXT24-IO-xxxx 12 direct sequence channels I/O to I/O: One-to-one (Peer-to-Peer mode) Network Topologies Radio Modem to I/O: One-to-many (Modbus I/O mode) Encryption ZXT9-IO-xxxx 256 bit AES ZXT24-IO-xxxx 128 bit AES Supplied Antenna Impedance – 50 Ω Connector – RPSMA Female VSWR – 2.0 Max (in-band) ZXT9-IO-xxxx Gain – 3 dBi Polarization – Vertical Length – 7.8 in (198 mm) Impedance - 50Ω Connector – RPSMA Female VSWR – 2.0 Max (in-band) ZXT24-IO-xxxx Gain – 2.1 dBi Polarization – Vertical Length – 4.38 in (113 mm) Antenna Connection RPSMA Male Digital Inputs Voltage Range Configuration Low Voltage (0) High Voltage (1) Pull Up/Down Current 0 to 48 VDC PNP (default) / NPN (selectable) 1 VDC Maximum Greater than 1 VDC 38 µA 2 DIs per module software selectable as counters with Frequency Input 0 to 20 KHz range Digital Outputs (Relay) Number of Relays 2 Type C (Normally Open and Normally Closed) Output Connection 3 Terminals Per Relay (Common, NO, NC) Comm. Connection 3.5 mm Terminal Block Ratings 250 VAC @ 4 A, 30 VDC @ 4 A Analog Inputs / Outputs 0 to 5 VDC, 0 to 10 VDC, 0 to 20 mA Ranges 4 to 20 mA Resolution 16 bit (Inputs), 12 Bit (Outputs) 100 MΩ - configured for Voltage AI Load Resistance 250 Ω - configured for Current AO Output Current 1 mA maximum configured for Voltage AO Source Load 450 Ω maximum configured for current Input Protection Over voltage to 2x max input voltage Power Power Connector Terminal Block Input Voltage 10 to 30 VDC Power Use ZXT9-IO-xxxx 6.8 W (maximum) ZXT24-IO-xxxx 4.5 W (maximum) Terminal blocks Wire Size 26 to 14 AWG Torque 0.5 Nm (min) 0.6 Nm (max) Environment Dimensions 5.12x5.12x2.37 in /130.1x130.1x60.2 mm Operating Temp -40 to 74°C (-40 to 165°F) Storage Temp -40 to 85°C (-40 to 185°F) Op Humidity 0 to 95% (Non-Condensing) Enclosure Rating IP67 Use Indoor and Outdoor Certifications EN55022: 2006 – Class A EN61000-6-1: 2006 – Heavy Industrial CE EN61000-4-2:2008 – ESD EN61000-4-3:2006 – EFT EN61000-4-6:2005 – Cond. Immunity Class A FCC FCC ID – ZXT9-RM – OUR-9XTEND FCC ID – ZXT24-RM – OUR-XBEEPRO UL C1D2, File – E245458 Controls and Indicators Signal Strength 8 Green RSSI LED’s indicate signal strength Power Green LED Receive Data Green LED Transmit Data Green LED Programming Port USB Reset Push Button www.bb-elec.com 53 WIRELESS Peer-to-Peer and Modbus I/O Zlinx Standard Wireless I/O PRODUCT FEATURES • Modular, Customizable Wire Replacement • Flexible configuration for multiple types of analog/digital I/Os • Software Selectable RF Transmit Power • Software Selectable Over-the-air Data Rate Zlinx™ Wireless Modbus I/O - flexible enough to fit your applications. These plug-n-play units combine traditional Modbus RTU remote analog and discrete I/O with built-in wireless connectivity. Wireless RTU serves as Modbus slave RTU in radio-based SCADA systems, or as a peer-to-peer communication platform. Two Ranges Available - Short, Long range. Active Repeaters - With built-in repeater functionality on 900 MHz -LR models, you can ensure vital signals get through. Modular - Just snap on your I/O and you are ready to communicate. Wide Temperature - Meets most indoor or outdoor applications. Rugged circuitry - prevents signal degradation. 128 / 256 Bit AES Encryption - Secures data. Selectable RF Transmit Power - Allows you to optimize the transmitter power for your application. Selectable Over-the-air Data Rate - Allows you to decrease the OTA Data Rate (on -LR and -LR-AU versions), effectively increasing the radio transmitter’s range. Exception Reporting - In Modbus mode, allows the reporting of possible problems with connected devices. Fail Safe - Allows you to set I/O to a safe state in the event of a communications failure. Calibration - Calculates correction factors to make I/O values better match your sensor. Communications Failure Alarm - Allows the first DO to be configured as a COM failure alarm indicator. Invert Output - You can invert the logic of all DO’s in peer-to-peer mode. Monitor - Use the Zlinx™ Manager Software to monitor your I/O. 54 • • • • • • Modbus ASCII /RTU Compatible 900 MHz and 2.4 GHz Versions Wide Operating Temperature Active Repeater Functionality 10 to 40 VDC & 24 VAC Input Power AES Encryption Ordering Information Model Number Description ZZ8D-XX-LR Base Modules * ZZ8D-NA-LR 868MHz, 2 AI, 2 A0, 2 DI, 2 D0 Sourcing, Long Range ZZ8D-NB-LR 868MHz, 4 DI, 4 D0 Sourcing, Long Range ZZ8D-NC-LR 868MHz, 2 AI, 2 A0, 2 DI, 2 D0 Sinking, Long Range ZZ8D-ND-LR 868MHz, 4 DI, 4 D0 Sinking, Long Range ZZ9D-XX-LR Base Modules * ZZ9D-NA-LR 900MHz, 2 AI, 2 AO, 2 DI, 2 DO Sourcing, Long Range ZZ9D-NA-LR-AU 900MHz, 2 AI, 2 AO, 2 DI, 2 DO Sourcing, Long Range ZZ9D-NB-LR 900MHz, 4 DI, 4 DO Sourcing, Long Range ZZ9D-NB-LR-AU 900MHz, 4 DI, 4 DO Sourcing, Long Range ZZ9D-NC-LR 900MHz, 2 AI, 2 AO, 2 DI, 2 DO Sinking, Long Range ZZ9D-NC-LR-AU 900MHz, 2 AI, 2 AO, 2 DI, 2 DO Sinking, Long Range ZZ9D-ND-LR 900MHz, 4 DI, 4 DO Sinking, Long Range ZZ9D-ND-LR-AU 900MHz, 4 DI, 4 DO Sinking, Long Range ZZ24D-XX-SR Base Modules* ZZ24D-NA-SR 2.4GHz, 2 AI, 2 AO, 2 DI, 2 DO Sourcing, Short Range ZZ24D-NB-SR 2.4GHz, 4 DI, 4 DO Sourcing, Short Range ZZ24D-NC-SR 2.4GHz, 2 AI, 2 AO, 2 DI, 2 DO Sinking, Short Range ZZ24D-ND-SR 2.4GHz, 4 DI, 4 DO Sinking, Short Range World-wide. Check with your local distributor for availability and options. * Check wireless regulations/standards in your geographic area. Model Number Description Expansion Modules ZZ-8DI-DC 8 Digital Inputs, 10-48VDC ZZ-8DO-T 8 Digital Outputs Sourcing ZZ-8DO-T1 8 Digital Outputs Sinking ZZ-8DO-R 8 Relay Outputs ZZ-4AI 4 Analog Inputs 4 Passive Source Analog Inputs, ZZ-4AO Requires Isolated External Power Supply ZZ-4AO-2 4 Analog Output Sourcing ZZ-4RTD1 4 RTD Input ZZ-4DI4DO-DCT 4 Digital Inputs, 10-48VDC, 4 Digital Outputs Sourcing ZZ-4DI4DO-DCT1 4 Digital Inputs, 10-48VDC, 4 Digital Outputs Sinking ZZ-2AI2AO 2 Analog Inputs, 2 Analog Outputs Accessories ZZ-PROG1-USB Zlinx USB Programming Module, Cable, Software CD ZZ24D-ANT1 2.4 GHz Spare Antenna ZZ9D-ANT1 900 MHz Spare Antenna ZZ-DIN 1 Replacement DIN Clip and Spring ZZ-TB1 Replacement Terminal Block Kit Peer-to-Peer and Modbus I/O Zlinx Standard Wireless I/O Specifications Base Module Radio Properties Model No. Frequency Software Selectable RF Power Options ZZ24D-Nx-SR ZZ9D-Nx-LR ZZ9D-Nx-LR-AU ZZ8D-Nx-LR 2.4 GHz 900 MHz * 900 MHz * 868 MHz ** 10mW, 16mW, 25mW, 40mW, 63mW 1mW,10mW, 100mW, 500mW, 1000mW 1mW, 10mW, 100mW, 500mW, 1000mW 1mW, 23mW, 100mW, 159mW, 316mW Factory RF Power Setting 63mW 1000mW 1000mW 316mW AES Encryption Over-the-air Data Rate 128 Bit 256 Bit 128 Bit 128 Bit 250 Kbps 9.6 or 115.2 Kbps 9.6 or 115.2 Kbps 24 Kbps Note: ZZ9D-Nx-LR and ZZ9D-Nx-LR-AU have software selectable OTA data rates. ZZ24D-Nx-SR ZZ9D-Nx-LR ZZ9D-Nx-LR-AU ZZ8D-Nx-LR Range w/Supplied Antenna (indoor / outdoor) maximum 300 Feet (91 Meters) / 1 Mile (1.6 Kilometers) 3000 Feet (914 Meters) / 14 Miles (23 Kilometers) 3000 Feet (914 Meters) / 14 Miles (23 Kilometers) 1800 Feet (549 Meters) / 25 Miles (40 Kilometers) Range w/High Gain Antenna (Outdoor) maximum N/A 40 Miles (64 Kilometers) 40 Miles (64 Kilometers) 25 Miles (40 Kilometers) *Note: 900 MHz units are not sold in Europe ** Note: 868 MHz units are not sold in North America Latency Base Module ZZ24D-xx-SR ZZ9D-xx-LR Modbus Digital 8mS 9mS Analog 15mS 104mS Peer-to-Peer Digital 20mS 55mS Analog 25mS 52mS Latency times were measured in a clean RF environment with devices less than 3 feet (1m) apart. Add 45mS per analog expansion module and 25mS per digital expansion module. ZZ8D-Nx-LR radios have a 10% maximum duty cycle. I/O Points Model No. Digital Inputs Digital Outputs Analog Inputs ZZxD-NA-xx (Base) 2 (Pull-up Resistors) 2 (Sourcing) 2 (mA, V) ZZxD-NB-xx (Base) 4 (Pull-up Resistors) 4 (Sourcing) --ZZxD-NC-xx (Base) 2 (Pull-up Resistors) 2(Sinking) 2 (mA, V) ZZxD-ND-xx (Base) 4 (Pull-up Resistors) 4 (Sinking) --ZZ-8DI-DC 8 (Pull-up Resistors) ----ZZ-8DO-T --8 (Sourcing) --ZZ-8DO-T1 --8 (Sinking) --ZZ-4DI4DO-DCT 4 (Pull-up Resistors) 4 (Sourcing) --ZZ-4DI4DO-DCT1 4 (Pull-up Resistors) 4 (Sinking) --ZZ-4AI ----4 (mA, V) ZZ-4AO ------ZZ-4A0-2 ------ZZ-2AI2AO ----2 (mA, V) ZZ-8DO-R --8 (Relay) --ZZ-4RTD1 ----4 (RTD) Software Programming Kits – Required to program your system Model Number Description ZZ-PROG1-USB Programming Module (USB Interface), USB cable and Software CD Analog Outputs 2 (V, mA, Sinking) --2 (V, mA, Sinking) --------------4 (V, mA, Sinking) 4 (V, mA, Sourcing) 2 (V, mA, Sinking) ----- Note: The Software CD is only available with the programming kit. Software and Firmware can also be downloaded at www.bb-elec.com www.bb-elec.com 55 WIRELESS continued... Peer-to-Peer and Modbus I/O Zlinx Stamdard Wireless I/O Specifications Digital inputs Voltage Range: 0 to 48 VDC Low Voltage (0): 0.8 V maximum High Voltage (1): 4.0 V minimum Pull Up Current: 38 micro-amps 2 DI inputs per module Software selectable as Frequency Input: frequency counters, 0 to 5 KHz range. digital outputs 10 to 40 VDC (Sourcing) Voltage Range: 0 to 48 VDC (Sinking) 40 mA per output Relay outputs Number of Relays: 8 Type: C -normally open & normally closed 3.5mm removable terminal block Output Connection: (2 per output) Common Connection: 3.5mm removable terminal block 250VAC @ 8A, 30VDC @5A (maximum per bank of 4 Ratings: as grouped on the label) radio properties (2.4 GHz - SR Models) Frequency: 2.4 GHz Output Power: 100 mW Receiver Sensitivity: -102 dbm The included antenna is a 4.25 inch omni-directional Antenna: with RPSMA connector. (p/n ZZ24D-ANT1) radio properties (900 MHx - LR Models) Frequency: 900 MHz Output Power: 1W Receiver Sensitivity: 100 dbm @ 115.2 K, 110 dbm @ 9.6K The included antenna is a 6.5 inch omni-directional Antenna: with RPSMA connector. (p/n ZZ9D-ANT1) radio properties (868 mhz Lr Models) Frequency: 868 MHz Output Power: 315 mW Receiver Sensitivity: -112 dbm The included antenna is a 6.5 inch omni-directional Antenna: with RPSMA connector. (p/n ZZ9D-ANT1) led indicators Tri-color – Off = No Signal = Weak Signal Receive Signal Strength: Red Yellow = Medium Signal Green = Strong Signal Green – Blinks with TD or RD RF Data: Off = No Data Green – Blinks with TD or RD Local Bus Data: Off = No Data Red – On = Power applied Power: Off = No Power 56 Analog Inputs and Outputs Ranges: Resolution: Input Accuracy: Output Accuracy: AI Load Resistance: AO Max Output Current: AO Max Load RTD Inputs Number of RTD: Wire Configuration: Type: Input Connection: Temperature Range: 0 to 10 VDC or 0 to 20 mA ZZ-4AO-2 is an active current source. All others are passive 12 Bit 0.2% full scale reading typical 0.27% full scale reading typical 100 Mega Ohms when configured for voltage input 250 Ohms when configured for current input 1 mA when configured for voltage output. 450 Ohms when configured for current output @ 12V 4 2, 3, and 4 wire PT100, PT1000 (Optimized for temperature coefficient of 385 C), Cu10 (Optimized for temperature coefficient of 427 C) 3.5mm removable terminal block (4 per output) PT100 = (-) 200 to (+) 650 C PT1000 = (-) 200 to (+) 100 C Cu10 = (-) 100 to (+) 260 C 0.1C cross at (-) 40 to (+) 80 C (+/-) 0.5 C typical (+/-) 2.0 C maximum Resolution: Accuracy @ 25 C: Accuracy (-)40 to (+) 80C Environmental Operating Temperature ZZ-8DO-R -40 to 55°C (-40 to 131°F) All Others -40 to 80°C (-40 to 176°F) Maximum Ambient Air Temperature ZZ-8DO-R 55°C (131°F) All Others 80°C (176°F) Storage Temperature -40 to 85°C (-40 to 185°F) Operating Humidity 0 to 95% Non-condensing Enclosure Plastic IP30 Mounting 35mm DIN Rail 1 Base Module supports up to 6 Expansion Expansion Modules 1.2 x 3.7 x 5.0 in Dimensions (2.9 x 9.3 x 12.7 cm) continued... Peer-to-Peer and Modbus I/O Zlinx Standard Wireless I/O Specifications Software A software CD is provided with programming kits Supported OS and contains Zlinx Manager software, Users Manual and Quick Start Guide. Agency Approvals FCC Part 15 Class A Download DoC at www.bb-elec.com CE Download DoC at www.bb-elec.com File Numbers E245458 (Class 1, Div 2) & E222870 (UL508) Models that are Class 1/Division 2 listed: ZZ24D-Nx-SR (2.4GHz, Short range) ZZ9D-Nx-LR (900 MHz, Long range) ZZ-2AI2AO ZZ-4AI ZZ-4AO ZZ-4AO-2 ZZ-4DI4DO-DCT ZZ-4DI4DO-DCT1 UL/cUL ZZ-4RTD1 ZZ-8DI-DC ZZ-8DO-R ZZ-8DO-T ZZ-8DO-T1 ZZ-PROG1-USB Class 1, Division 2 exceptions: ZZ-8DO-R is not UL508 listed. ZZxxD-Nx-MR, ZZxxD-Nx-xR-AU and ZZ8D-Nx-xR models are not Class 1, Division 2 Listed but are UL508 listed. MTBF (Hours) ZZ24D-NA-SR 85547 ZZ24D-NB-SR 137106 ZZ24D-NC-SR 86247 ZZ24D-ND-SR 138362 ZZ24D-NA-MR 88006 ZZ24D-NB-MR 142946 ZZ24D-NC-MR 88746 ZZ24D-ND-MR 144909 ZZ9D-NA-MR 88006 ZZ9D-NB-MR 144746 ZZ9D-NC-MR 88746 ZZ9D-ND-MR 144909 ZZ9D-NA-LR 88195 ZZ9D-NB-LR 143446 ZZ9D-NC-LR 88938 ZZ9D-ND-LR 145422 ZZ8D-NA-LR 88195 ZZ8D-NB-LR 143446 ZZ8D-NC-LR 88938 ZZ8D-ND-LR 145422 ZZ-4AI 136050 ZZ-4AO 113996 ZZ-2AI2AO 119183 ZZ-8DI-T 317530 ZZ-8DO-T 313100 ZZ-8DO-T1 317530 ZZ-4DI4DO-DCT 197045 ZZ-4DI4DO-DCT1 200795 ZZ-8DO-R 40670 ZZ-4RTD1 243007 ZZ-4AO-2 113996 Zlinx Radio Modem & I/O Compatibility Radio Modem Zlinx Base I/O Module ZP24D-250RM-SR ZZ24D-Nx-SR ZP9D-115RM-LR ZZ9D-Nx-LR / ZZ9D-Nx-LR-AU ZP8D-24RM-LR ZZ8D-Nx-LR Power (Base Modules) Source Voltage Power Connection Wiring Terminals Wire Type Conductors Wire Range Tightening Torque Field Wiring Temp Rating Power Consumption SR Models 900 MHz LR Models 868 MHz LR Models Power (Expansion Modules) An external power supply is required (not included) 10-40 VDC, 24 VAC Class 2, (2.7A Maximum) Removable Terminal Block, 3.81 mm spacing Copper Wire Only One Conductor Per Terminal 28 to 16 AWG 1.7 lb – in 105°C Minimum (Sized for 60°C ampacity). 10.0 W 9.5 W 12.0 W Source Class 2 Power Derived from base modules Voltage and current listed on product label. Power Consumption ZZ-4AI ZZ-4AO ZZ-2AI2AO ZZ-8DI-DC ZZ-8DO-T ZZ-8DO-T1 ZZ-4DI4DO-DCT ZZ-4DI4DO-DCT1 ZZ-8DO-R ZZ-4RTD1 ZZ-4AO-2 Outputs 1.0 W 1.1 W 1.2 W 0.4 W 15.8 W 1.1 W 8.1 W 1.0 W 3.2 W 0.4 W 6.0 W ZZ-8DO-R All Others Wire Type Conductors Wire Size Tightening Torque Replacement Parts ZZ-DIN1 ZZ-TB1 ZZ24D-ANT1 ZZ9D-ANT1 Relay Output, 250VAC 2 A General Purpose/Point 8 A General Purpose Total Low Voltage, Limited Energy Communications Protocol Copper Wire Only One Conductor Per Terminal 28 to 16 AWG 0.2 Nm (Newton-Meters) Replacement DIN clip and spring for all ZZ products, also comes with spare screws for enclosure Replacement terminal block kit for ZZ products. Kit includes (1) Two position TB (3.81mm) (1) Four position TB (3.5mm) (1) Eight position TB (3.5mm) (1) Cover for local Bus 2.4 GHZ band antenna 900 MHz Spare Antenna www.bb-elec.com 57 WIRELESS IP67 Outdoor Rated Industrial Radio Modem Zlinx Xtreme Wireless Radio Modems PRODUCT FEATURES • • • • • • • • • • • • Do you need to get a digital signal across a highway or river? Zlinx® Xtreme Radio Modems can do it faster, easier, and less expensively than stringing cable. Easy plug-and-play set-up saves installation and maintenance time. These compact and rugged IP67 units are ideal for outdoor applications requiring Serial-to-Serial (RS-232/422/485) connectivity or to connect Zlinx® Xtreme Wireless I/O’s to a Modbus RTU Master over a wireless network. Point-to-Multi Point connections are also possible. Zlinx® Industrial Wireless products operate in license-free, Proprietary RF 900 MHz and 2.4 GHz ISM bands. Select the 900 MHz version for longer distances. For further flexibility, the output power is software selectable. The 900 MHz units offer 256 bit AES Encryption. The 2.4 GHz units have 128 bit AES Encryption. 58 IP67 rated for outdoor applications RS-232/422/485, serial communications Modbus Compatible Ranges to 40 miles (64 km) Line of Sight & Antenna Dependent Heavy duty machine mount industrial grade case and components Signal strength indicator aids trouble shooting 900 MHz and 2.4 GHz versions Wide temperature range -40 to 74°C Wide range power input: 10VDC to 30VDC AES Encryption UL Class1/Division2 NEMA TS2 Ordering Information Model Number Description Zlinx Xtreme IP67 900MHz Radio Modem, Long Range, ZXT9-RM RS- 232/422/485 Zlinx Xtreme IP67 2.4GHz Radio Modem, Short Range, ZXT24-RM RS-232/422/485 Zlinx Xtreme IP67 900MHz Radio Modem Kit, (2) Radio ZXT9-RM-KIT Modems, (2) 24VDC IP67 Power Supplies, (1) USB Programming Cable World-wide. Check with your local distributor for availability and options. * Check wireless regulations/standards in your geographic area. Accessories CLG-60-24 IP67 Power Supply, Panel Mount, 24V DC, 60W ZXT9-ANT 900 MHz Spare Antenna ZZ24D-ANT1 2.4 GHz Spare Antenna ZXTMT Zlinx Xtreme Conduit Kit IP67 Outdoor Rated Industrial Radio Modem Zlinx Xtreme Wireless Radio Modems Specifications RF Properties Physical Standard 802.15.4 Frequency ZXT9-RM 900 MHz ISM (902-928 MHz) ZXT24-RM 2.4 GHz ISM (2.4 to 2.5 GHz) Transmit Power 1 mW, 10 mW, 100 mW, 500 mW ZXT9-RM 1 W – Software Selectable 10 mW, 16 mW, 25 mW, 30 mW ZXT24-RM 63 mW – Software Selectable Receiver Sensitivity -100 dBm Over the Air Data Rate ZXT9-RM 9.6 or 115.2 kbps Software Selectable ZXT24-RM 250 kbps Outdoor Range Supplied Antenna 14 mi (23 km) ZXT9-RM High Gain Antenna 40 mi (64 km) Supplied Antenna 1.5 mi (2.4 km) ZXT24-RM High Gain Antenna 10 mi (16 km) Range estimates based on optimal RF conditions and an unobstructed line of sight. Transmission Method ZXT9-RM ZXT24-RM Modulation Channel Capacity ZXT9-RM ZXT24-RM Network Topologies Encryption ZXT9-RM ZXT24-RM Supplied Antenna ZXT9-RM ZXT24-RM Modem Antenna Con. Software Support Features Serial Properties Data Rates ZXT9-RM ZXT24-RM Data Bits Parity Stop Bits Flow Control RS-232 RS-422 RS-485 (2/4 Wire) SD Control Termination Industrial Bus Power Power Connector Input Voltage Power Use FHSS DSSS FSK 10 hop sequences share 50 Frequencies 12 Direct Sequence Channels Peer-to-Peer, Point-to-Point, Point-to-Multi Point 256 bit AES 128 bit AES Impedance – 50 Ω Connector – RPSMA Female VSWR – 2.0 Max (in-band) Gain – 3 dBi Polarization – Vertical Length – 7.8 in (198 mm) Impedance - 50Ω Connector – RPSMA Female VSWR – 2.0 Max (in-band) Gain – 2.1 dBi Polarization – Vertical Length – 4.38 in (113 mm) RPSMA Male Environment Dimensions Operating Temp Storage Temp Op Humidity Enclosure Rating Use Certifications UL CE FCC 1.2 to 230.4 kbps 1.2 to 115.2 kbps 8 None, Even, Odd, Mark, Space 1 or 2 None or Software Connector: Terminal Block Signals: TD, RD, RTS, CTS, GND Connector: Terminal Block Signals: TDA(-) TDB(+) RDA(-) RDB(+) GND Connector: Terminal Block Signals (4-Wire): TDA(-), TDB(+), RDA(-), RDB(+), GND Signals (2-Wire): Data A(-), Data B(+), GND Automatic Bit Wise 120Ω Ohm DIP Switch Selectable MODBUS RTU Terminal Block 10 to 30 VDC ZXT9-RM: 1.7 W (typical), 5.8 W (maximum) ZXT24-RM: 1.2 W (typical), 3.5 W (maximum) 5.12x5.12x2.37 in /130.1x130.1x60.2 mm -40° to 74°C (-40 to 165°F) -40° to 85°C (-40 to 185°F) 0 to 95% (Non-Condensing) IP67 Indoor and Outdoor UL, cUL, Class 1 Div 2 Groups A, B, C, D File E245458 EN55022: 2006 – Class A EN61000-6-1: 2006 – Heavy Industrial EN61000-4-2:2008 – ESD EN61000-4-3:2006 – EFT EN61000-4-6:2005 – Cond. Immunity Class A FCC ID – ZXT9-RM – OUR-9XTEND FCC ID – ZXT24-RM – OUR-XBEEPRO NEMA TS2 Controls and Indicators Signal Strength 8 Green RSSI LED’s indicate signal strength Power Green LED Receive Data Green LED Transmit Data Green LED Programming Port USB Reset Push Button Win XP, 7 RSSI signal range test www.bb-elec.com 59 remote monitoring with wireless sensors... by Bill Conley Product Manager - Cellular & Proprietary Devices IN Using solar power and radio to establish Ethernet connectivity ...where there’s no access to a power grid or internet infrastructure. If remote sensors are to be autonomous, and if they are to report their data in real time, they must have a reliable power source and a stable Ethernet connection. The United States Geological Survey (USGS), for example, monitors water conditions with a nationwide array of automated sensors, and uses their data to update the USGS web site with the latest information. Many of these sensors must function in locations where there is no access to the power grid and no Internet infrastructure, and where regular human interaction with the sensor installation would be impractical. B&B Electronics, specialists in M2M connectivity solutions for harsh and remote environments, worked with the USGS to overcome those issues. The team integrated a sensor with a solar panel and a NEMA 3R weatherproof enclosure that contained B&B Electronics’ Zlinx Xtreme IP67-rated outdoor radio transmitter with a high-gain antenna, maintenance-free battery and lifetime warranty. The goal was to create a water-monitoring station that could reliably transmit its data up to 64 km, 24/7. Nothing can be accomplished without power, so the first step was to determine the daily power requirements for each sensor and its attached radio transmitter. A typical sensor using an analog output might use 0.60 Amp hours per day (0.4 W x 24 hours at 12 V.). A digital sensor might use 0.72 Amp hours per day. If connected to a an IP67-rated outdoor radio transmitter like the B&B Electronics Zlinx Extreme, which requires around 2.4 Amp hours per day, the total power requirement would be 3.12 Amp hours per day. energy received on a given surface area over a specified period of time. In a location like Chicago, IL, for example, with an average yearly solar insolation level of 3.72, a 50 W solar panel would provide enough power to operate a transmitter and its associated sensor while simultaneously charging the attached 12 V battery so that transmission can continue during the hours of darkness. After calculating the power requirements for each USGS installation, an appropriate solar panel was selected. After that it was a matter of radio physics. Currently, the most commonly used unlicensed frequencies are 2.4 GHz and 900 MHz, although the move to digital television has freed up new bandwidth at lower frequencies. At 2.4 GHz radio has greater bandwidth, but less range – and for now – more interference from other transmitters. Additionally, the higher the radio frequency, the more it will be affected by multipath propagation, a phenomenon that occurs when broadcast radio signals bounce off intervening objects and arrive at the receiver at different times, and out of sequence. At 900 MHz radio has greater range, less competition from other devices and is less susceptible to multipath propagation. But it provides less bandwidth. A transmitter like the Zlinx Extreme can broadcast in either frequency. So the successful remote installation involved experimenting with both options to see which one provided the best signal strength in the local environment. There is no need for an onsite generator when the power requirements are that low. A solar panel and attached battery will do the job. The size and cost of the required solar panel will be a function of the location and its solar insolation, the measure of solar 60 www.bb-elec.com REAL-TIME Extreme Solution for Remote Monitoring Applications ... monitoring volcano activity wirelessly. What do icelandic volcanoes do? The answer to this question is extremely important for many people and companies – not only on Iceland. In 2010 air traffic was shut down due to volcano ash in the atmosphere. Thousands of people waited in vain for scheduled flights and numerous cargo shipments were delayed across Europe. For these reasons and more, remote monitoring of volcanoes is important to all of us. Wireless routers help transfer data from seismological stations via cellular mobile operator network technology to a central location where it is processed and analyzed. “Wireless data transfer from geo-measuring devices is one of the large varieties of applications where cellular mobile operator network communication is really efficient. Reliability and security of such a solution is vital. Also important are entrylevel and operating costs compared to other technologies available on market,” says Otakar Müller, B&B Electronics Sales and Marketing Director for Cellular, EMEA. His opinion is proven by the operation of hundreds of other, similar applications. Wireless routers are also suitable for industrial uses, data transfer from ATMs, ticketing terminals and kiosks, and more. Cellular Wireless ters, GPS et c. ted to Ethern et 0, RS232 ro uter k? rk? Howesdoe itswitorwo D o d A TA How Cellulaerless ir lular WCel Wireless etc. seismo GPS ers, seismomet mete rs, GPS etc. connected connecto tedEthernet to Ethernet router RS232 10/100, 10/10 0, RS23 2 router PC o o canncan data vizualiz lvol voatio and processing Cellulaerless Wir it workD?ATA s e o d How DA TA DAT A seismometers, GPS etc. connected to Ethernet 10/100, RS232 router PC n lizatioes ing a vnizouaan daltPC proc s d a c a vizualization vo dat and processing PC alization data vizu and processing 61 WIRELESS Industrial Grade Radio Modems – Up to 40mi/64km Range Zlinx Wireless Radio Modems PRODUCT FEATURES • • • • • • • • • • Do you need to get a digital signal across a highway or river or to the other end of your big warehouse? Zlinx radio modems can do the job faster, easier, and less expensively than stringing cable. Easy plug-andplay set-up saves installation and maintenance time. These compact and rugged units are compatible with Modbus and Profibus so no additional converters are required. Despite their low prices, these are not wimpy consumer or office grade products. Select the power level you need to punch through whatever distance and interference situations you encounter. Zlinx radio modems are built to handle the heat, cold, and environments of industrial operations. RS-232/422/485, Serial communications Modbus compatible – no additional converters needed Ranges up to 40 miles (64 km) Heavy duty DIN mount industrial grade case and components Signal strength indicator aids trouble shooting 900 MHz, 868 MHz, 2.4 GHz Versions Wide temperature range -40º to 85º C Wide Range Power Input: 10 to 48 VDC or 18 to 30 VAC AES Encryption UL Class1/Division2 (Long Range Only) Ordering Information Model Number Description Zlinx Radio Modem 2.4 GHz Short Range, RS ZP24D-250RM-SR 232/422/485 Zlinx Radio Modem 900 MHz Long Range, RSZP9D-115RM-LR 232/422/485 ZP9D-115RM-LR-AU Zlinx Radio Modem 900 MHz Australian Version ZP8D-24RM-LR* Zlinx Radio Modem, 868 MHz, Long Range RM-LR-KIT 900 MHz Radio Modem, Long Range Starter Kit RM-SR-KIT 2.4 GHz Radio Modem Short Range Starter Kit RM-LR824-KIT 868 MHz Radio Modem Kit Kits contain: (2) radio modems, (2) power supplies, 24VDC 30W, and (2) 6ft/1.8m serial cables World-wide. Check with your local distributor for availability and options. * European - Check wireless regulations/standards in your geographic area. Accessories 62 DR-75-24 75W Power Supply ZP9D-ANT1 900 MHz Spare Antenna ZP24D-ANT1 2.4 GHz Spare Antenna ZP9D-DIN1 Replacement DIN clip kit for ZP9D radio modems ZP24D-DIN1 Replacement DIN clip kit for ZP24D radio modems ZP9D-TB1 Replacement terminal block kit for radio modems. Contains complete set of terminal blocks and dip switch cover DRPM25 Panel Mount Adapter Industrial Grade Radio Modems – Up to 40mi/64km Range Zlinx Wireless Radio Modems MODEL NUMBER: RF Properties Standard Range(with included antenna) Frequency Transmit Power Software Support Features Included Omni Antenna ZP24D-250RM-SR ZP8D-24RM-LR IEEE 802.15.4 Proprietary Radio up to 300ft/91m indoor Up to 24.9mi/40km outdoor or 1mi/1.6km outdoor 2.4 GHz 868 MHz 100mW 316mW Win XP, Win 7 RSSI signal range test Modem emulation ZP9D-115RM-LR Proprietary Radio up to 3000ft/.91km indoor or 14mi/22.5km outdoor 900 MHz 1W 2.1 dBi 3 dBi 3 dBi Antenna Connector Serial Properties Baud Data Bit; Parity; Stop Bit RS-232 RS-422 RS-485 Wireless Link Failure External Reverse Polarity SMA male jack connector, omni directional (included with product) 1200, 2400, 4800, 9600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 19200, 38400, 57600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 115200 115200, 230400 7, 8; None, even, odd, mark, 7, 8; None, even, odd, mark, space; 1, 2 8 only; none only; 1 only space; 1, 2 DB9F DCE or Terminal Block (TX, RX, GND available on Terminal Block Removeable terminal block, 2 or 4 wire - TX+, TX-, RX+, RX-, GND, 120 Ohm Dipswitch selectable Removeable terminal block, 2 or 4 wire - TX+, TX-, RX+, RX-, GND, Bit wise, 120 Ohm Dipswitch selectable Removeable terminal block, Open collector, dry contact, 40mA Power Power Supply Power Consumption Dimensions Environmental Operating Temperature Storage Temperature Operating Humidity Enclosure Rating Rating Mounting LED Status Certifications FCC CE UL RoHS directive (lead free) 10-48 VDC, 18-30 VAC, Removeable terminal block 2.0W max 6W max 5.0W max 1.2W x 3.3D x 4.7H -40° to 85ºC -40° to 85ºC 10 to 90% non-condensing IP30 DIN rail mount, 35mm Power, Signal Strength, Wireless Data FCC Part 15 Class B CISPR (EN55022) Class B EN61000-6-1 Generic Standards for Residential, Commercial, & Light Industrial EN61000-4-2-ESD, EN61000-4-3 RFI, EN61000-4-4 EFT, EN61000-4-5 Surge, EN61000-4-6 CI, EN61000-4-8 Power Frequency Magnetic, EN61000-4-11 Voltage Dips & Interruptions UL, cUL UL, cUL UL, cUL, Class 1 Div 2 Groups A, B, C, D File E245458 Yes www.bb-elec.com 63 WIRELESS Dual Band (2.4 GHz, 5 GHz) Ethernet Bridge/Router AirborneM2MTM Enterprise Series PRODUCT FEATURES • • • • • • • AirborneM2MTM Dual Band Wireless The AirborneM2MTM line of enterprise wireless Ethernet Routers and Bridges are built for networking equipment in an array of machine to machine (M2M) applications. The small compact form factor, integrated options and ease of use make it ideal for commercial enterprise environments. Dual-Band Wi-fi The AirborneM2MTM products establish wireless connections over both 2.4 GHz and 5 GHz bands. Whenever the 2.4 GHz airspace is overcrowded with competing wireless transmission, AirborneM2MTM products can be switched over to 5 GHz band to keep data flowing. Enterprise Class Security Security protocols are important to mission-critical wireless M2M applications. AirborneM2MTM multi-layered security approach addresses the requirements of Enterprise-class networks and corporate IT departments. These advanced security features include wireless security (801.11i/WPA2 Enterprise); network security (EAP authentication and certificate support); communication security (SSH functionality and fully encrypted data tunnels); and device security (multi-level encryption capability to protect configuration data). SpeedLink™ Roaming The latest AirborneM2MTM SpeedLink™ roaming feature further enhances the high level of connection reliability. SpeedLink™ enables AirborneM2MTM devices to roam quickly and freely throughout a wireless network without loosing important data. If you’re walking around a hospital or driving through a warehouse, SpeedLink™ ensures you stay connected. 64 10/100 Mbps to 802.11a/b/g/n (2.4 GHz, 5 GHz) Wide operating temperature Range (-20°C to +85°C) Compact form factor AirborneM2MTM SpeedLink roaming provides enhanced connection reliability Advanced Enterprise Class wireless security (WPA2-Enterprise, WPA, WEP, EAP) Available in OEM version (without enclosure) Supported by Airborne Management Center (AMC) device discovery, management and control application software Ordering Information Model Number Description AirborneM2MTM Enterprise Series Dual Band 802.11a/b/g/n (2.4 GHz, 5 GHz) Ethernet bridge ABDN-ER-DP551 and router with WPA2-Enterprise, WPA, WEP, EAP Security Support Advanced Enterprise Security Dual Band 802.11a/b/g/n (2.4 GHz, 5 GHz) Ethernet bridge ABDN-ER-DP553 and router OEM Version World-wide. Check with your local distributor for availability and options. AirborneM2MTM Enterprise models operate in a wide-range of commercial applications: Medical devices Retail / Point of sale products Material handling & Logistics Test & Measurement Security & Access control Dual Band (2.4 GHz, 5 GHz) Ethernet Bridge/Router AirborneM2MTM Enterprise Series Specifications Technology Technology IEEE 802.11a/b/g/n, Wi-Fi compliant Wired Interface 10/100 Ethernet port (Bridge, Router (NAT3) Modes) 2.4 ~ 2.4835 GHz (US/Canada/Europe) Frequency 5.150 ~ 5.350 GHz 5.725 ~ 5.825 GHz Modulation Technology DSSS, CCK, OFDM Modulation Type DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM Network Access Modes Infrastructure (Client), Ad Hoc US/Canada: Channels Wireless Data Rate MAC Network Protocols Receive Sensitivity 802.11 b/g Receive Sensitivity 802.11 a Dimensions 11 Channels 802.11b/g 13 Channels 802.11a Europe: 13 Channels 802.11b/g 19 Channels 802.11a France: 4 Channels 802.11b/g 802.11b = 11, 5.5, 2, 1 Mbps 802.11a/g = 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n = 65, 58.5, 42, 39, 26, 19.5, 13, 6.5 Mbps CSMA/CA with ACK, RTS, CTS TCP/IP, ARP, ICMP, DHCP, DHS, UDAP, TFTP, UDP, PING 54Mb/s = -72 dBm 36Mb/s = -78 dBm 18Mb/s = -84 dBm 6Mb/s = -89 dBm 11Mb/s = -86 dBm 1Mb/s = -92 dBm 54Mb/s = -74 dBm 36Mb/s = -80 dBm 18Mb/s = -86 dBm 6Mb/s = -90 dBm 63.4x99.0x46.7 mm (2.6x4.0x1.9 in) Features Transmit Power Security Protocols Antenna Power Supply Supply In-rush Current 802.11b 15 dBm (31.6mW) 802.11g 12.6dBm (18.12mW) 802.11a 17 dBm (50.1mW) Disabled, WEP 64 & 128bit, WPA (TKIP), WPA (AES), WPA2 (AES), 802.1x (EAP) Supplicant 802.11I, WPA & WPA2 Enterprise supplicants (EAP-TLS, EAP-TTLS(MSCHAPv2), EAPTTLS (MDS5), EAP-PEAPv0 (MSCHAPv2, LEAP), EAP-FAST, LEAP) Supports Certificates and Private Key Upload and Storage (Multiple) Integrated RP-SMA Omni-directional 2dBi 2.4/5 GHz Antenna 5.0VDC+/-5% 3000mA (MAX) for 20ms Current (Tx, 802.11g) = 370mA Typ. DC Characteristics Operating Operating Current (Rx, 802.11g) = 200mA Typ. Operating Temperature: -20° to +85°C Storage Temperature: -20° to +85°C Environmental Relative humidity: 5% - 95% (non-condensing) Vibration: 20G peak-to-peak, 20Hz-2KHz swept Shock: 1500G peak-to-peak, 0.5mS duration Interfaces 10/100 Ethernet Enclosure Nylon (Gray) LED Indicators 3 indicator LEDs (Power, LINK, COMM) North America: FCC Title 47 Part 15 Class B Sub C Intentional IOC RSS210 Agency Approvals Radiator, Europe: CE ETSI EN300 328 RoHS & WEEE compliant www.bb-elec.com 65 WIRELESS M2M Dual Band (2.4GHz, 5GHz) Ethernet Bridge/Router; Serial Server AirborneM2MTM Industrial Series PRODUCT FEATURES • RS-232/422/485 or 10/100 Mbps Ethernet to 802.11a/b/g/n (2.4 GHz, 5 GHz) • One or two serial ports, one Ethernet port • Advanced Enterprise class wireless security • 2 kV serial ESD surge suppression • Variable DC power supply (5-36 VDC), PoE 802.3af Power over Ethernet • Extended operating temperature range (-40°C to +85°C) • AirborneM2MTM SpeedLink roaming - enhanced connection reliability • Supported by Airborne Management Center (AMC) device discovery, management and control application software The AirborneM2MTM line of industrial wireless device serial servers and Ethernet Bridge/Routers are built for networking equipment in an array of machine-to-machine (M2M) applications. AirborneM2MTM Industrial Series feature industrial strength packaging and support a wide temperature rating (-40° to 85°C) to withstand challenging M2M environments. Available in both single and dual serial port models or a single Ethernet port model. Power options include 5-36VDC input or PoE 802.3af (Power over Ethernet) on select models. Ordering Information Model Number Description Dual Band AirborneM2MTM Industrial Wireless Ethernet Bridge/ ADDN-ER-IN5010 Router with 802.11i/WPA2 Enterprise Security Support Dual Band AirborneM2MTM Industrial Wireless Ethernet Bridge/ ABDN-ER-IN5018 Router with 802.11i/WPA2 Enterprise Security Support; PoE Dual Band Industrial wireless serial server with one ABDN-SE-IN5410 RS-232/422/485 to 802.11a/b/g/n Dual Band Industrial wireless serial server with two ABDN-SE-IN5420 RS-232/422/485 to 802.11a/b/g/n Dual-Band Wi-Fi The AirborneM2MTM products establish wireless connections over both 2.4 GHz and 5 GHz bands. Whenever the 2.4 GHz airspace is overcrowded with competing wireless transmission, AirborneM2MTM products can be switched over to 5 GHz band to keep data flowing. World-wide. Enterprise Class Security Security protocols are important to mission-critical wireless M2M applications. AirborneM2MTM multi-layered security approach addresses the requirements of Enterprise-class networks and corporate IT departments. These advanced security features include wireless security (801.11i/WPA2 Enterprise); network security (EAP authentication and certificate support); communication security (SSH functionality and fully encrypted data tunnels); and device security (multi-level encryption capability to protect configuration data. SpeedLink™ Roaming The latest AirborneM2MTM SpeedLink™ roaming feature further enhances the high level of connection reliability. SpeedLink™ enables AirborneM2MTM devices to roam quickly and freely throughout a wireless network without loosing important data. If you’re walking around a hospital or driving through a warehouse, SpeedLink™ ensures you stay connected. 66 Check with your local distributor for availability and options. Accessories PS-WDS: 120-240VAC 50/60Hz; 5VDC, 2 A barrel connector power supply MDR-20-24: 120-240VAC 50/60 Hz to 24VDC 1.0 A DIN rail ACH2-DBAT-DP002: 2 dBi portable (Rubber duck) 2.4/5 GHz antenna ACH2-DBAT-DP003: 3.8/5.5 dBi portable (Rubber duck) 2.4/5 GHz antenna AirborneM2MTM industrial products can be deployed into a wide range of applications across various industries including: Vehicle Telematics & Diagnostics Material Handling & Logistics Industrial Automation Test & Measurement Security & Access Control Military communications M2M Dual Band (2.4GHz, 5GHz) Ethernet Bridge/Router; Serial Server AirborneM2MTM Industrial Series Specifications Technology Wireless Technology IEEE 802.11 a/b/g/n, Wi-Fi Compliant 2 ports, RS-232/422/485, (RS-232/422 4 wire or RS-485 2 wire) Wired Interface 10/100 Ethernet port (Bridge, Router (NAT3) Modes) Software selectable 2.4~2.4835 GHz (US/Canada/Europe) 2.4~2.497 GHz (Japan) Frequency 5.150 ~ 5.350 GHz 5.725 ~ 5.825 GHz Modulation Technology DSSS, CCK, OFDM Modulation Type DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM Network Access Infrastructure (Client), Ad Hoc Modes Channels Wireless Data Rates Network Protocols Receive Sensitivity 802.11 b/g Receive Sensitivity 802.11 a Wireless Security Secure Communications Transmit Power US/Canada: 11 Channels 802.11b/g 13 Channels 802.11a Europe: 13 Channels 802.11b/g 19 Channels 802.11a France: 4 Channels 802.11b/g Japan: 14 Channels 802.11b 13 Channels 802.11g 23 Channels 802.11a 802.11a/g 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11b = 11, 5.5, 2, 1 Mbps 802.11n 65, 58.5, 42, 39, 26, 19.5, 13, 6.5 Mbps TCP/IP, ARP, ICMP, DHCP, DHS, UDAP, TFTP, UDP, PING, HTTP, FTP 54Mb/s = -72 dBm 36Mb/s = -78 dBm 18Mb/s = -84 dBm 6Mb/s = -89 dBm 11Mb/s = -86 dBm 1Mb/s = -92 dBm 54Mb/s = -74 dBm 36Mb/s = -80 dBm 36Mb/s = -80 dBm 6Mb/s = -90 dBm Open, WEP 64 & 128 bit, WPA-PSK (TKIP), WPA2-PSK (AES), 802.1x (EAP), WPA-Enterprise, WPA2-Enterprise, EAP-TLS/MSCHAPv2, EAP-TTLS/MSCHAPv2, EAP-TTLS (MD5), EAP-PEAPv0/MSCHAPv2, LEAP - Zero host security footprint - Advanced certificate storage and management - SSH and SSL tunneling - Encrypted configuration 802.11b 15 dBm (31.6mW) 802.11g 12.6dBm (18.12mW) 802.11a 17 dBm (50.1mW) Power Input Voltage 5-36VDC +/-5%, 500mA (MAX) 2-position terminal block, 2.1mm barrel jack; Power Connection PoE 802.3af Power Use 2.5W at 5VDC Supply In-rush Current 3000mA (MAX) for 20ms PoE PoE using a 802.3af Class 1 PSE device LED Indicators 4 LEDs COMM, LINK, POWER, POST (Power on Self Test) Environmental Operating Temperature -40° to +85°C Storage Temperature -40° to +85°C Op. Humidity 5% - 95% (non-condensing) Mechanical Antenna RP-SMA Omni-directional 2dBi 2.4/5 GHz Antenna Vibration 20G peak-to-peak, 20Hz-2KHz swept Shock 1500G peak-to-peak, 0.5mS duration Enclosure Metal Enclosure Mounting Panel mount, optional DIN rail brackets Dimensions 120.14 x 120.12 x 29.21 mm (4.89 x 4.73 x 1.15in) Regulatory Approvals FCC Part 15.247, Class B Sub C Modular Approval Industry Canada RSS-210 CE ETSI EN300-328 v1.7.1 ETSI 60950-1 Directive 2004/108/EC ETSI EN 55022:2006 + A1:2007 (emissions) ETSI EN 55024:1998 + A1:2001 ETSI EN 55024:1998 + A2:2003 (immunity) FCC Part 15 Subpart B:2007 - Part 15.107(b) (conducted emissions, Class A) - Part 15.109(g) (radiated emissions, Class B) Industry Canada ICES-003:2004, Issue 4 AS/NZS CISPR 11:2004 (Australia/New Zealand) RoHS and WEEE Compliant www.bb-elec.com 67 WIRELESS M2M Dual Band (2.4 GHz, 5 GHz) Access Point AirborneM2MTM Access Point PRODUCT FEATURES • • • • • • • • • The AirborneM2MTM line of industrial wireless access points is built for networking equipment in an array of machine-to-machine (M2M) applications. AirborneM2MTM Access Point features industrial strength packaging and support a wide temperature rating (-40° to 85°C) to withstand challenging M2M environments. Power options include 5-36VDC input or PoE 802.3af (Power over Ethernet) on select models. Combination Access Point and Client Capability The AirborneM2MTM Access Point enables M2M equipment to create a self sufficient Wi-Fi network and easy access to equipment data or resources from WiFi enabled devices. The product also has the capability to be switched from an access point to a client; supporting both a single or dual RS-232/422/485 serial ports or a single 10/100 Mbps Ethernet port. The Ethernet port can be placed into either a router or bridge mode. Dual-Band Wi-Fi The AirborneM2MTM products establish wireless connections over both 2.4 GHz and 5 GHz bands. Whenever the 2.4 GHz airspace is overcrowded with competing wireless transmission, AirborneM2MTM products can be switched over to 5 GHz band to keep data flowing. Enterprise Class Security Security protocols are important to mission critical wireless M2M applications. The AirborneM2MTM Access Point multi-layer security approach addresses the requirements of Enterprise-class networks and corporate IT departments. These advanced security features include wireless security (802.11i/WAP2 enterprise); authentication security using WPA2 (AES-CCMP) and device security (multi-layered encryption). The AirborneM2MTM access point includes a fully functional DHCP server to provide unique addresses for each authenticated client. Up to 10 clients can be supported on the local Wi-Fi network. 68 RS-232/422/485 or 10/100 Mbps Ethernet to 802.11a/b/g/n (2.4 GHz, 5 GHz) Combination Access Point/ Client, one or two serial ports, one Ethernet port Supports up to 10 Wi-Fi clients Advanced Enterprise class wireless security 2 kV serial ESD surge suppression Variable DC power (5-36 VDC), PoE 802.3af Power over Ethernet Extended operating temperature range (-40°C to +85°C) AirborneM2M SpeedLink roaming for enhanced connection reliability Supported by Airborne Management Center (AMC) device discovery, management and control application software Ordering Information Model Number Description Dual Band; AirborneM2MTM Industrial Access Point; APXN-Q5428 802.11a/b/g/n; PoE World-wide. Check with your local distributor for availability and options. Accessories PS-WDS: 120-240VAC 50/60Hz; 5VDC, 2 A barrel connector power supply MDR-20-24: 120-240VAC 50/60 Hz to 24VDC 1.0 A DIN rail ACH2-DBAT-DP002: 2 dBi portable (Rubber duck) 2.4/5 GHz antenna ACH2-DBAT-DP003: 3.8/5.5 dBi portable (Rubber duck) 2.4 GHz, 5 GHz antenna AirborneM2MTM industrial products can be integrated and deployed into a wide range of applications across various industries including: Vehicle Telematics & Diagnostics Material Handling & Logistics Industrial Automation Test & Measurement Security & Access Control Military communications M2M Ethernet Dual Band (2.4 GHz,5 GHz) Access Point AirborneM2MTM Access Point Specifications Technology Wireless Technology IEEE 802.11 a/b/g/n, Wi-Fi Compliant 2 ports, RS-232/422/485, (RS-232/422 4 wire or RS-485 2 wire) Wired Interface 10/100 Ethernet port (Bridge, Router (NAT3) Modes) Software selectable 2.4~2.4835 GHz (US/Canada/Europe) 2.4~2.497 GHz (Japan) Frequency 5.150 ~ 5.350 GHz 5.725 ~ 5.825 GHz Modulation Technology DSSS, CCK, OFDM Modulation Type DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM Network Access Access Point Infrastructure (Client), Ad Hoc Modes Channels Wireless Data Rates Network Protocols Receive Sensitivity 802.11 b/g Receive Sensitivity 802.11 a Wireless Security Secure Communications Transmit Power US/Canada: 11 Channels 802.11b/g 13 Channels 802.11a Europe: 13 Channels 802.11b/g 19 Channels 802.11a France: 4 Channels 802.11b/g Japan: 14 Channels 802.11b 13 Channels 802.11g 23 Channels 802.11a 802.11a/g 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11b = 11, 5.5, 2, 1 Mbps 802.11n 65, 58.5, 42, 39, 26, 19.5, 13, 6.5 Mbps TCP/IP, ARP, ICMP, DHCP, DHS, UDAP, TFTP, UDP, PING, HTTP, FTP 54Mb/s = -72 dBm 36Mb/s = -78 dBm 18Mb/s = -84 dBm 6Mb/s = -89 dBm 11Mb/s = -86 dBm 1Mb/s = -92 dBm 54Mb/s = -74 dBm 36Mb/s = -80 dBm 36Mb/s = -80 dBm 6Mb/s = -90 dBm Open, WEP 64 & 128 bit, WPA-PSK (TKIP), WPA2-PSK (AES), 802.1x (EAP), WPA-Enterprise, WPA2-Enterprise, EAP-TLS/MSCHAPv2, EAP-TTLS/MSCHAPv2, EAP-TTLS (MD5), EAP-PEAPv0/MSCHAPv2, LEAP - Zero host security footprint - Advanced certificate storage and management - SSH and SSL tunneling - Encrypted configuration 802.11b 15 dBm (31.6mW) 802.11g 12.6dBm (18.12mW) 802.11a 17 dBm (50.1mW) Power Input Voltage 5-36VDC +/-5%, 500mA (MAX) 2-position terminal block, 2.1mm barrel jack; Power Connection PoE 802.3af Power Use 2.5W at 5VDC Supply In-rush Current 3000mA (MAX) for 20ms PoE PoE using a 802.3af Class 1 PSE device LED Indicators 4 LEDs COMM, LINK, POWER, POST (Power on Self Test) Environmental Operating Temperature -40° to +85°C Storage Temperature -40°to +85°C Op. Humidity 5% - 95% (non-condensing) Mechanical Antenna RP-SMA Omni-directional 2dBi 2.4/5 GHz Antenna Vibration 20G peak-to-peak, 20Hz-2KHz swept Shock 1500G peak-to-peak, 0.5mS duration Enclosure Metal Enclosure Mounting Panel mount, optional DIN rail brackets Dimensions 120.14 x 120.12 x 29.21 mm (4.89 x 4.73 x 1.15 in) Regulatory Approvals FCC Part 15.247, Class B Sub C Modular Approval Industry Canada RSS-210 CE ETSI EN300-328 v1.7.1 ETSI 60950-1 Directive 2004/108/EC ETSI EN 55022:2006 + A1:2007 (emissions) ETSI EN 55024:1998 + A1:2001 ETSI EN 55024:1998 + A2:2003 (immunity) FCC Part 15 Subpart B:2007 - Part 15.107(b) (conducted emissions, Class A) - Part 15.109(g) (radiated emissions, Class B) Industry Canada ICES-003:2004, Issue 4 AS/NZS CISPR 11:2004 (Australia/New Zealand) RoHS and WEEE Compliant www.bb-elec.com 69 6 Overlooked Places Wi-Fi can save you Time, Money and Trouble. 1 2 3 Flexible Work Cells MOBILE CONNECTIONS LEGACY DEVICES Industrial assembly was traditionally done by breaking a process down into individual steps and positioning machinery to maximize the efficiency and throughput of each machine. But that model lacked the flexibility needed for the production of small and customized lot sizes. The solution is the work cell, where the machinery and devices required for a specific project can be temporarily grouped together, and released for other uses as dictated by circumstances. But that means re-cabling the work cells every time there’s a change. Wi-Fi makes it easier - and cheaper - to set up and rearrange work cells. Flexible Work Cells 70 Cable connections don’t allow for much mobility. In applications like shipping and receiving, where the value of mobile machinery like forklifts is greatly enhanced if those devices have network connections, an industrial-grade Wi-Fi wireless access point like the B&B Electronics’ APXN-Q5428 can keep mobile equipment connected to the network even as it moves around a facility. A truck could connect to a forklift to download or upload delivery manifests and shipment details. Inventory systems, printers, scales and other tools can communicate directly with a vehicle to expedite workflow. Wi-Fi clients like laptops, tablets or smart phones can connect directly to the vehicle. Even vehicle maintenance is simplified, as onboard diagnostics and telematics can be monitored directly or from a remote location. The enormous installed base of devices using serial communications isn’t going anywhere any time soon. But as newer protocols like Ethernet and Wi-Fi have appeared, it is becoming harder to find laptops or computers equipped with serial ports. One solution is to equip serial devices with wireless Ethernet serial servers. Wireless serial server technology can turn a serial device into one more node on the network and give it communications capabilities that it was never designed to possess. A serial device could also be equipped with an embedded Wi-Fi access point module like the B&B Electronics’ ABDN-ER-DP511, which creates a selfsustaining wireless hotspot much like the one at the corner coffee shop. Handheld Wi-Fi clients can then connect to it using Android, iOS or Windows. It’s worth re-thinking some of the ways industrial data communications have been made considering where Wi-Fi can fit into the mix. Technological advances like multiple-in-multiple-out (MIMO) transmitting and receiving are making Wi-Fi increasingly useful in industrial applications. Bandwidth and reliability have increased dramatically, and implementation costs have dropped. 4 5 6 CABLE VULNERABILITY HARD-TO-WIRE AREAS HAZARDOUS LOCATIONS Although network cables are commonly run under floors, or through walls or drop ceilings, some portion of the cable must eventually be exposed as it makes the final run to an attached device. That’s not a big issue in an office environment, but in industrial applications that final run leaves a cable vulnerable to serious damage. Cables may be crushed by moving machinery, stepped on, pulled, bent, or soaked in damaging fluids like solvents. And when cables fail, installing new cable is often cheaper and easier than tracking down the fault point in the existing installation. If this happens often enough it will ultimately create a confusing rat’s nest of old and new wiring. Sometimes you just can’t wire a widget. The expenses involved in running cable over a river or highway, for example, can be prohibitive. Even an indoor installation can be problematical, depending upon where a device needs to be placed. And moving data any significant distance over cable will call for expensive fiber optic cables, receivers and transceivers. Fiber optic cable provides for enormous bandwidth and, as demonstrated by the telcos, it will carry data across entire continents. But how many applications would actually require that much range or bandwidth? For far less money you can install off-the-shelf Wi-Fi bridges that will create connections with speeds of up to 150 Mbps at distances of up to 15 km, depending upon local conditions. In 1989 a solar flare created a magnetic storm that knocked out the power grid for all of Quebec by inducing unexpected current on the power lines. Industrial motors and other high-power devices create magnetic fields that will affect nearby copper cabling in much the same way, though on a smaller scale. With luck, the only result will be data transmission errors and blue screens. But more serious events will damage expensive equipment. The problem is magnified in temporary installations at remote locations. Imagine setting up a large generator system for a remote construction site, or to provide temporary power after a natural disaster. You’d need to tie together everything from SCADA to Modbus, and you’d be working in a slightly disorganized environment full of moving vehicles and workmen. Murphy’s Law tells us what would happen to any exposed cable. Trenching your cable would help, but it would add time and expense to the project. And the final run would still be highly vulnerable. It would be easier to do the job with Wi-Fi. Hard-To-Wire Locations And the greater the distance between connected devices, the more likely it becomes that communicating devices will be getting their power from different building ground references. When they do, copper cable can create a ground loop path. Again, you’ll be able to count yourself lucky if the only result is a blue screen. These problems can’t be addressed with ordinary surge suppression, which only tries tries to limit spikes between the signal and ground line. (When the ground line rises, as it does in ground loop situations, surge suppression won’t stop it.) You could install isolators, which allow the lines to float while keeping the local side at the proper ground and signal level. And you could invest in fiber optics, which are natively immune to electromagnetic interference (EMI), spikes surges and ground loops. But if you’d prefer to save yourself some money and trouble, you could just use Wi-Fi. www.bb-elec.com 71 WIRELESS Secure, Rugged Wi-Fi Modules WLNN-XX-DP551 Series PRODUCT FEATURES • Quick time to market and reduced integration costs • 802.11a/b/g/n Wi-Fi (2.4 GHz, 5 GHz) • Airborne PowerSave firmware reduces power consumption and extends battery life in mobile devices • Extended Operating Temperature Range (-40°C to +85°C) and environmental specifications • AirborneM2M SpeedLink roaming provides enhanced connection reliability • Advanced Enterprise Class wireless security • AirborneM2M PortFlex capability enables any combination of comm ports (UART, SPI, GPIO, Ethernet and 802.11 interfaces) • FCC Part 15 Class B Sub C Modular Approval minimizes regulatory requirements • Backwards compatible with previous generations of AirborneM2M embedded modules AirborneM2MTM Embedded Dual Band Wireless Device Server and Ethernet Solution Modules Serial & Ethernet to 802.11a/b/g/n (2.4 GHz, 5 GHz) The AirborneM2M line of highly-integrated 802.11 wireless modules allow OEMs to Wi-Fi enable devices used in an array of machine-to-machine (M2M) applications. B&B delivers all of the necessary RF technology, networking stacks and advanced security features in a compact, singleboard package, reducing integration costs for OEMs and providing for a quick time to market. Big Performance in Small and Ruggedized Package The AirborneM2M series delivers the industry’s most rugged, highlyintegrated, embedded Wi-Fi module solution. AirborneM2M modules meet extended operating temperature and shock/vibration specifications of the most demanding M2M applications. Utilizing a 32bit ARM9 processor and the high-performance Atheros AR6203 802.11 radio, the new AirborneM2M modules deliver increased transmit power and receive sensitivity, contributing to superior range performance. SpeedLink™ Roaming The new AirborneM2M SpeedLink roaming feature provides enhanced connection reliability, enabling OEM devices to roam freely within a wireless network without loss of data or connection. Flexible & Easy to Integrate AirborneM2M incorporates support for both serial and Ethernet to Wi-Fi 802.11 2.4 or 5 GHz communications. Utilizing AirborneM2M PortFlex capability, OEMs may configure via software any combination of UART, SPI, Ethernet, GPIO and 802.11 interfaces. Each individual port can be independently configured. 72 The AirborneM2M modules are footprint and pin-compatible with their predecessors. Our commitment to maintaining hardware and software compatibility assures OEMs of a simple, future-proof migration path even as wireless technology evolves. Enterprise Class Security Security protocols are important to mission-critical wireless M2M applications. AirborneM2M multi-layered security approach addresses the requirements of Enterprise-class networks and corporate IT departments. These advanced security features include wireless security (801.11i/WPA2 Enterprise); network security (EAP authentication and certificate support); communication security (SSH functuionality and fully encrypted data tunnels); and device security (multi-level encryption capability to protect configuration data.) Ordering Information Model Number Description 802.11a/b/g/n, 10/100 Ethernet adapter, Advanced Enterprise WLNN-ER-DP551 Security WLNN-AN-DP551 802.11a/b/g/n, UART interface, Advanced Enterprise Security 802.11a/b/g/n, UART with RS-232/422/485 Driver Control, WLNN-SE-DP551 Advanced Enterprise Security WLNN-SP-DP551 802.11a/b/g/n, SPI interface, Advanced Enterprise Security WLNN-EK-DP551 Design and Development Kit World-wide. Check with your local distributor for availability and options. Accessories ACH2-DBAT-DP002 - 2 dBi portable (Rubber duck) 2.4/5 GHz antenna ACH2-DBAT-DP003 - 3.8/5.5 dBi portable (Rubber duck) 2.4 GHz, 5 GHz antenna Secure, Rugged Wi-Fi Modules WLNN-XX-DP551 Series Specifications Technology Technology IEEE 802.11a/b/g/n, Wi-Fi compliant 2.4 ~ 2.4835 GHz (US/Canada/Europe) Frequency 5.150 ~ 5.350 GHz 5.725 ~ 5.825 GHz Modulation Technology DSSS, CCK, OFDM DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, Modulation Type 64QAM Network Access Modes Infrastructure (Client), Ad Hoc US/Canada: 11 Channels 802.11b/g 13 Channels 802.11a Europe: 13 Channels 802.11b/g Channels 19 Channels 802.11a France: 4 Channels 802.11b/g Japan: 14 Channels 802.11b 13 Channels 802.11g 23 Channels 802.11a 802.11b:11, 5.5, 2, 1 Mbps Wireless Data Rate 802.11a/g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: 65, 58.5, 42, 39, 26, 19.5, 13, 6.5 Mbps MAC CSMA/CA with ACK, RTS, CTS TCP/IP, ARP, ICMP, DHCP, DHS, UDAP, TFTP, UDP, Network Protocols PING 54Mb/s = -72 dBm 36Mb/s = -78 dBm = -84 dBm Receive Sensitivity 802.11 b/g 18Mb/s 6Mb/s = -89 dBm 11Mb/s = -86 dBm 1Mb/s = -92 dBm 54Mb/s = -74 dBm 36Mb/s = -80 dBm Receive Sensitivity 802.11 a 18Mb/s = -86 dBm 6Mb/s = -90 dBm Transmit Power 802.11a/b/g Security Protocols (Client mode) Antenna Supply Supply In-rush Current DC Characteristics Environmental Interfaces Digital I/O LED Indicators Connector Agency Approvals 802.11b 15 dBm 802.11g 12.6 dBm 802.11a 17 dBm Disabled, WEP 64 & 128bit, WPA (TKIP), WPA (AES), WPA2 (AES), 802.1x (EAP) Supplicant 802.11I, WPA & WPA2 Enterprise supplicants (EAP-TLS, EAPTTLS(MSCHAPv2), EAPTTLS(MDS5), EAP-PEAPv0(MSCHAPv2, LEAP), EAP-FAST, LEAP) Supports Certificates and Private Key Upload and Storage (Multiple) Two (2) U.FL coaxial connectors, 50 Ohms Max gain @ 5 GHz = 5.5 dBi Max gain @ 2.4 GHz = 4.1 dBi 3.3VDC +/-5%, 650 mA (MAX) 1500mA (MAX) for 400us Operating Current (Tx, 802.11g) = 370mA Typ. Operating Current (Rx, 802.11g) = 200mA Typ. Operating Temperature: -40° to +85°C Storage Temperature: -40° to +85°C Relative humidity: 5% - 95% (non-condensing) Vibration: 20G peak-to-peak, 20Hz-2KHz swept Shock: 1500G peak-to-peak, 0.5mS duration Dual UART (960KBAUD), RS232/ 422/ 485, SPI (1bit/8MHz), 10/100 Ethernet, PortFlex 8 GPIO 4 indicator LED signals (RF ACT, POST, CONNECT, RF LINK), Signal Strength 36 pin High Density SMT connector from Hirose (DF1236DS-0.5V), 4mm Height North America: FCC Title 47 Part 15 Class B Sub C Intentional Radiator, IOC RSS210 Europe: CE ETSI EN300 328 RoHS & WEEE compliant www.bb-elec.com 73 EXPERT CORNER Smartphones & M2M Connecting made easy, finally. by Bill Conley You could argue that wireless data communications began in 1782, when Claude Chappe used semaphore towers to send messages between Paris, France, and the city of Lille, 220 km away. Called the ‘Telegraph,” Chappe’s system was the origin of the word used for electrical messaging systems developed in the following century. It didn’t work in bad weather, it didn’t work at night, there was no network security and the data rate between Paris and Lille was roughly one symbol per minute. But it was the cutting edge of technology in its day, and an instant success. New telegraph lines soon sprang up all over Europe. When Morse code and electrical signaling came along they were faster and more efficient than the Chappe Telegraph, but the name stuck. Data communications have continued to improve ever since. And just as happened with Chappe’s telegraph, it would seem that new technologies must automatically supplant their predecessors. But sometimes that’s impractical. For example, in spite of the improvements of things like USB and Wi-Fi, there are still millions of perfectly serviceable serial devices in the world. And new serial devices are still coming on line. Serial technology is reliable, it’s still very useful and so many people have so much invested in existing serial devices that the standard won’t be disappearing any time soon. But as tablets and smart phones become more ubiquitous in the corporate and M2M business world, connecting to serial ports has become a bit more complicated. Tablets and smart phones don’t have serial ports. In fact they tend to have limited wired connectivity of 74 any kind, largely relying upon wireless communications for their interaction with the rest of the world. They’re wonderful devices, but they’re not natively designed to interact with serial equipment. Manufacturers, suppliers and integrators 2M equipment – as well as their customers - have a continuing need for serial communications. So what can they do about the communications gap? How it works Serial device servers can be wired or wireless. The most popular types are network or TCP/IP device servers. In either case, wired or wireless, the serial server translates the serial data into an Internet Protocol (IP) format that can be transmitted across a network. Wired serial device servers use Ethernet cable to connect to the local area network (LAN). Wireless device servers contain a Wi-Fi client similar to the one in your laptop and connect via Wi-Fi, or 802.11. (The most common standards are 802.11b/g and 802.11b/g/n.) Wireless servers can connect to either an infrastructure network or to an AdHoc network. When the Serial Device Server (SDS) network interface is connected to a LAN it provides an IP address that all other network devices can use for sending and receiving information. This address is unique to the SDS. Since this address is the location for all interactions, a secondary reference is used to locate the information or resource required for the specific interaction. This is called a port number. Using the combination of IP address and port number it is possible to uniquely locate any serial port on the network. It works like this: A serial device server has a physical serial port connected to port 8023 on the network interface. The network interface connects to the network and gets an IP address of 192.168.2.100. After combining the two pieces of information the full address of the serial port would be 192.168.2.100:8023. Any network-connected device capable of accessing that address can receive data from, or send data to, the serial port. So what’s the problem? Current network SDS devices are designed to be used with an existing network infrastructure. If you have a manufacturing facility, warehouse or office, odds are that you already have a network installed - wired, wireless or both. Connecting to these networks has become much easier with the latest versions of SDS technology. But what happens when you want to talk to a device that isn’t covered by an existing wireless network? A large portion of the desired serial data may come from remote locations that are out of the coverage range of the corporate Wi-Fi network, or in an area where access to the available network is restricted because of IT policy and security rules. How can users access the data from these devices? Embedded Hotspots There is emerging technology that supports embedded Access Point functionality without changing the SDS functionality. As an example, B&B Electronics’ SDS technology features an embedded AP device that creates a small, self-sustaining Wi-Fi network around the remote equipment that isn’t all that different from the hotspot in a coffee shop. As your technician comes into range of the network, his Wi-Fi tablet or smart phone sees the network, connects to it and receives an IP address from the embedded AP. His device can then access the serial port on the AP using the appropriate IP address and port number. It doesn’t change the way the SDS devices are used, it just makes them easily accessible to tablets and phones. Benefits of embedded AP: • • Tablets and smart phones will be able to access serial data in addition to existing network devices like laptops. Network devices won’t need reconfiguring to use static IP addresses. • • • A self-maintaining network won’t lose devices or compromise their access. Users can simultaneously add and access wireless and wired devices on the embedded hotspot. There is no change to the existing use paradigm of networked serial device servers. The example B&B device can support up to two serial devices, an Ethernet 10/100 network and multiple wireless clients simultaneously. It provides WPA/WPA2 security and an embedded DHCP server. Both external box and embedded module versions are available. Serial ports have been around for a long time, and they represent an earlier generation in communications engineering. But that doesn’t mean that tablets and smart phones shouldn’t talk to them. They still have a lot of information to share. Talk Back! Visit Bill’s wireless blog and chat it up! We’d love to hear from you! www.bb-elec.com/Tech-Support/Bill www.bb-elec.com 75 WIRELESS Secure, Rugged Wi-Fi Access Point Modules APMN-Q551 Series PRODUCT FEATURES • Quick time to market and reduced integration costs • 802.11a/b/g/n Wi-Fi radio (2.4 GHz, 5 GHz) • AirborneM2M Power Save firmware reduces power consumption and extends battery life in mobile devices • Extended operating temperature Range (-40°C to +85°C) and environmental specifications • AirborneM2M Speed Link roaming provides enhanced connection reliability • AirborneM2M PortFlex capability enables any combination of communication ports (UART, SPI, GPIO, Ethernet and 802.11 interfaces) • FCC Part 15 Class B Sub C Modular Approval minimizes regulatory requirements • Backwards compatible with previous generations of AirborneM2M embedded modules AirborneM2M Embedded Dual Band Access Point Module or Client 802.11a/b/g/n (2.4 GHz, 5 GHz) The AirborneM2M line of highly-integrated 802.11 wireless access point modules allow OEMs to Wi-Fi enable devices used in an array of machine-to-machine (M2M) applications. B&B delivers all of the necessary RF technology networking stacks and advanced security features in a compact, single-board package, reducing integration costs for OEMs and providing for a quick time to market. Big Performance in Small and Ruggedized Package The AirborneM2M series delivers the industry’s most rugged, highly integrated, embedded wireless access point Wi-Fi module solution AirborneM2M modules meet extended operating temperature and shock vibration specifications of the most demanding M2M applications. Utilizing a 32bit ARM9 processor and the high-performance Atheros AR6203 802.11 radio, the new AirborneM2M modules deliver increased transmit power and receive sensitivity, contributing to superior range performance. SpeedLink™ Roaming The new AirborneM2M Speed Link roaming feature provides enhanced connection reliability, enabling OEM devices to roam freely within a wireless network without loss of data or connection. Flexible & Easy to Integrate AirborneM2M incorporates support for both wireless access point and serial to Wi-Fi communications. Utilizing AirborneM2M Port Flex capability, OEMs may configure via software any combination of UART, SPI, Ethernet, GPIO and 802.11 interfaces. Each individual port can be independently configured. 76 The AirborneM2M modules are footprint and pin-compatible with their predecessors. Our commitment to maintaining Hardware and software compatibility assures OEMs of a simple, future-proof migration path even as wireless technology evolves. Enterprise Class Security Security protocols are important to mission critical wireless M2M applications. The AirborneM2M™ Access Point multi-layer security approach addresses the requirements of Enterprise-class networks and corporate IT departments. These advanced security features include wireless security (802.11i/WAP2 enterprise), authentication security using WPA2 (AES-CCMP) and device security (multi-layered encryption). The AirborneM2M™ Access Point includes a fully functional DHCP server to provide unique addresses for each authenticated client. Up to 10 clients can be supported on the local Wi-Fi network. Ordering Information Model Number Description 802.11a/b/g/n, 10/100 Industrial wireless access point/ APMN-Q551 router/client: UART, SPI and RS-232/422/485 wired interfaces WLNN-EK-DP551 Design and Development Kit World-wide. Check with your local distributor for availability and options. Accessories ACH2-DBAT-DP002 - 2 dBi portable (Rubber duck) 2.4/5 GHz antenna ACH2-DBAT-DP003 - 3.8/5.5 dBi portable (Rubber duck) 2.4 GHz, 5 GHz antenna Secure, Rugged Wi-Fi Access Point Modules APMN-Q551 Series Specifications Technology Technology IEEE 802.11a/b/g/n, Wi-Fi compliant 2.4 ~ 2.4835 GHz (US/Canada/Europe) Frequency 5.150 ~ 5.350 GHz 5.725 ~ 5.825 GHz Modulation Technology DSSS, CCK, OFDM Modulation Type DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM Network Access Modes Access Point, Infrastructure (Client), Ad Hoc Channels US/Canada: 11 Channels 802.11b/g 13 Channels 802.11a Europe: 13 Channels 802.11b/g 19 Channels 802.11a France: 4 Channels 802.11b/g Japan: 14 Channels 802.11b 13 Channels 802.11g 23 Channels 802.11a 802.11b: 11, 5.5, 2, 1 Mbps Wireless Data Rate 802.11a/g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: 65, 58.5, 42, 39, 26, 19.5, 13, 6.5 Mbps MAC CSMA/CA with ACK, RTS, CTS Network Protocols TCP/IP, ARP, ICMP, DHCP, DHS, UDAP, TFTP, UDP, PING 54Mb/s = -72 dBm 36Mb/s = -78 dBm Receive Sensitivity 18Mb/s = -84 dBm 802.11 b/g 6Mb/s = -89 dBm 11Mb/s = -86 dBm 1Mb/s = -92 dBm 54Mb/s = -74 dBm Receive Sensitivity 36Mb/s = -80 dBm 802.11 a 18Mb/s = -86 dBm 6Mb/s = -90 dBm Transmit Power Security Protocols (AP and AdHoc modes) Security Protocols (Client mode) Antenna Supply Supply In-rush Current DC Characteristics Environmental Interfaces Digital I/O LED Indicators Connector Agency Approvals 802.11b 15 dBm (31.6mW) 802.11g 12.6dBm (18.12mW) 802.11a 17 dBm (50.1mW) Disabled, WEP 64 & 128bit, WPA-PSK(TKIP), WPA2-PSK(AES) Disabled, WEP 64 & 128bit, WPA-PSK(TKIP), WPA2-PSK(AES), WPA & WPA2 Enterprise (EAPTLS, EAP-TTLS, EAP-PEAP, EAP-FAST, LEAP) and a suite of Migration modes (wpa-leap64, wpa-leap128, wpa-psk64, wpa-psk128, wpapsk128-tkip, wpa2-psk-tkip) Supports Certificates and Private Key Upload and Storage (Multiple) Two (2) U.FL coaxial connectors, 50 ohms Max gain @ 5 GHz = 5.5 dBi Max gain @ 2.4 GHz = 4.1 dBi 3.3VDC +/-5%, 650mA (MAX) 1500mA (MAX) for 400us Operating Current (Tx, 802.11g) = 370mA Typ. Operating Current (Rx, 802.11g) = 200mA Typ. Operating Temperature: -40° to +85°C Storage Temperature: -40° to +85°C Relative humidity: 5% - 95% (non-condensing) Vibration: 20G peak-to-peak, 20Hz-2KHz swept Shock: 1500G peak-to-peak, 0.5mS duration Dual UART (960KBAUD), RS232/ 422/ 485, SPI (1bit/8MHz), 10/100 Ethernet, PortFlex 8 GPIO 4 indicator LED signals (RF_ACT, POST, CONNECT, RF_LINK), Signal Strength 36 pin High Density SMT connector from Hirose (DF12-36DS-0.5V), 4mm Height North America: FCC Title 47 Part 15 Class B Sub C Intentional Radiator, IOC RSS210 Europe: CE ETSI EN300 328 RoHS & WEEE compliant www.bb-elec.com 77 WIRELESS High Performance Wireless Ethernet Bridge GHOSTBRIDGE PRODUCT FEATURES • • • • • • • • • • • Seamlessly connect remote devices to your network, or bridge two LAN’s together. The GhostBridge provides a high speed wireless Ethernet bridge with zero configuration required. Units are sold as a preconfigured pair and require no further setup. Simply mount it, aim it and plug it in to your network or device using the included PoE adapters. Long Range, High Speed Wireless Ethernet Link Point and play setup Outdoor rated, UV stabilized enclosure Integrated 80 degree sector antenna Maximum data rate of 150 Mbps Up to 15 km line of sight range Wide temperature range of -30° to 80°C Power, Link and Signal Strength LED’s provide instant view of status Includes both DC and AC powered PoE adapters PoE pass-through Ethernet port to connect local devices such as IP camera (24V Passive) Preconfigured WPA2 128 bit security Ordering Information Model Number Description 5 GHz Secure Wireless Ethernet Bridge GhostBridge5 (sold in preconfigured pairs) 5 GHz Indoor/Outdoor Wireless Ethernet Bridge GhostBridge5-EU (sold in preconfigured pairs EU Power Supply) 5 GHz Indoor/Outdoor Wireless Ethernet Bridge GhostBridge5-UK (sold in preconfigured pairs) UK Power Supply) 2.4 GHz Indoor/Outdoor Wireless Ethernet Bridge GhostBridge2-EU2 (sold in preconfigured pairs EU Power Supply) 2.4 GHz Indoor/Outdoor Wireless Ethernet Bridge GhostBridge2-UK (sold in preconfigured pairs) UK Power Supply) World-wide. Check with your local distributor for availability and options. Swivel wall-mount bracket Accessories GMT25 Swivel wall-mount bracket IASFST MOCAP tape - 36 ft/11 m roll, 1 in/2.5 cm wide Applications Water and Waste-water treatment Warehouse automation Security - IP cameras Monitoring and Instrumentation 78 High Performance Wireless Ethernet Bridge GHOSTBRIDGE Specifications ethernet interface Ethernet Port 1 RJ45 Ethernet Port 2 RJ45 LED’s Power, LAN1, LAN2, 4 wireless signal strength Power 24V PoE powered device through Ethernet port + pins PoE Power 4,5, - pins 7, 8 (2) 100-240VAC input @ 50-60 Hz 24V out, 0.5A out PoE injectors Included PoE Injectors (2) DC input PoE injector with 1m power jack to stripped wires Power 8 Watts maximum power consumption RF Operating Frequency 5470 – 5825 GhostBridge5 TX Power (Avg) 21 – 27 dBm +/- 2dB (varies by mode/conditions) RX Sensitivity -74 – 96 dBm +/- 2dB (varies by mode/conditions) Antenna Type Integrated 2x2 MIMO. 80 degree sector Antenna gain 14.6 – 16.1 dBi over 4.9 – 5.9 GHz Security Each pair is preconfigured to WPA2 128 bit Mechanical 11 x 3.2 x 1.2 in (28 x8 x 3 cm) body Dimensions 11 x 3.2 x 2.4 in (28 x8 x 6 cm) including built-in brackets Weight per unit 0.86 lbs (0.4 kg) Shipping weight 3.0 lbs (1.4 kg) Integrated pole mount, wire ties included Mounting Optional wall/pole mount swivel bracket sold separately Enclosure IP54. UV Stabilized plastic. Environmental Operating Temperature -30 to 80°C (-40 to 176°F) Storage Temp -40 to 85°C (-40 to 185°F) Operating Humidity 0 to 95 % (Non-condensing) Approvals / Certifications Emissions FCC Class B, CISPR Class B (EN55022) CE EN61000-6-1:2007 EN61000-4-2:2008 Electrostatic Discharge EN61000-4-3:2006 Radiated Immunity EN61000-4-4:2004 Electrical Fast Transients - Burst EN61000-4-6:2005 Conducted Immunity EN61000-4-11:2004 Voltage Dips and Interruptions EN 301 489-1 V1.4.1: 2002-08 Electromagnetic Compatibility EN 301 489-17 V1.2.1: 2002-08 Electromagnetic Compatibility EN 301 893-1 V1.4.1: 2007 Directive for 5 GHz Radio Equipment EN 50385: 002 RF Exposure Limits EN 60950-1: 2006 Safety for Information Technology Equipment www.bb-elec.com 79
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021