PROHEAT 2X REVOLUTION Deep Cleaner

PROHEAT 2X  REVOLUTION Deep Cleaner
PROHEAT 2X®
REVOLUTION™
Deep
Cleaner
_______________
USER GUIDE
1858 SERIES
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
To reduce the risk of fire, electric
shock, or injury:
»Unplug from electrical socket when not
in use and before cleaning, maintaining
or servicing the appliance.
»This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved. Cleaning and user maintenance
shall not be made by children without
supervision.
»Children should be supervised to ensure
that they do not play with the appliance.
»If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
»Do not run appliance over cord.
»Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts of the appliance and its
accessories.
»Use only the type and amount of liquids
specified under the Operations section of
this guide.
»Do not leave appliance when plugged in.
»Always connect to a properly earthed electrical socket.
Do not modify earthed plug.
»Use indoors only.
»Do not allow to be used as a toy.
»Use only as described in the user guide.
»Use only manufacturer’s recommended attachments.
»Do not use with damaged cord or plug.
»Do not immerse in water or liquid.
»If appliance is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water; do not
attempt to operate it and have it repaired at an authorized
service center.
»Liquid or steam must not be directed towards
equipment containing electrical components.
»Do not pull or carry by cord, use cord as a handle, close
door on cord, or pull cord around sharp edges
or corners.
»Keep cord away from heated surfaces.
»Do not unplug by pulling on cord.
»To unplug, grasp the plug, not the cord.
»Do not handle plug or appliance with wet hands.
»Do not put any object into openings.
»Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
»Turn off all controls before unplugging.
»Use extra care when cleaning on stairs.
»Do not use to pick up flammable or combustible
liquids, such as petrol, or use in areas where they
may be present.
»Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.)
»Do not use appliance in an enclosed space filled
with vapors given off by oil base paint, some
mothproofing substances, flammable dust, or other
explosive or toxic vapors.
»Do not pick up hard or sharp objects such as glass, nails,
screws, coins, etc.
»Keep appliance on a level surface.
»Do not carry appliance while in use.
»Unplug before attaching the TurboBrush™ tool.
» Do not pick up anything that is burning or smoking, such
as cigarettes, matches, or hot ashes.
»If your appliance is fitted with a nonrewireable BS 1363
plug it must not be used unless a 13 amp (ASTA approved
to BS 1362) fuse is fitted in the carrier
contained in the plug. Spares may be obtained from your
BISSELL supplier. If for any reason the plug is cut off,
it must be disposed of, as it is an electric shock hazard
should it be inserted into a mains socket.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, USE INDOORS ONLY . DO NOT IMMERSE.
USE ONLY ON SURFACES MOISTENED BY THE
CLEANING PROCESS. USE ONLY BISSELL
CLEANING PRODUCTS INTENDED FOR USE
WITH THIS MACHINE.
TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, ALWAYS INSTALL FLOAT
BEFORE ANY WET PICK-UP OPERATION.
SAVE THESE INSTRUCTIONS
FOR OPERATION ON A 220-240 VOLT A.C. 50-60 HZ POWER SUPPLY ONLY.
This model is for household use only.
2
www.BISSELL.com
Thanks for buying a BISSELL deep cleaner!
We love to clean and we’re excited to share one of our innovative products
with you. We want to make sure your deep cleaner works as well in
six years as it does today, so this guide has tips on using (pages 7-12),
maintaining (pages 12-14), and if there is a problem, troubleshooting
(page 15).
In just a few simple assembly steps, you’ll be ready to deep clean. Flip to
page 5 and let’s get started!
What’s In The Box?
1.
5.
2.
3.
6.
4.
7.
BISSELL
8.
9.
10.
1. Upper Handle
2.1 Screw attached to
Upper Handle
3. Base with Dirty Water Tank
4. Clean Water Tank
5.Carry Handle
6.BISSELL 2X Professional
Formula
7.BISSELL Antibacterial
Formula
8. Accessory bag & hose
9.Attachments/accessories
(vary by model)
10. Nozzle Clean Out Tool
NOTE: Not all accessories
come with every model. Be
sure to check the carton for
additional tools.
Safety Instructions . . . . . . . . . . 2
Troubleshooting . . . . . . . . . . . . 15
Product View . . . . . . . . . . . . . . . 4
Guarantee . . . . . . . . . . . . . . . . . . 16
Assembly . . . . . . . . . . . . . . . . . . . 5
Service . . . . . . . . . . . . . . . . . . . . . 16
Cleaning Formulas . . . . . . . . . . 6
Contact Information . . . . . . . . . 16
Operations . . . . . . . . . . . . . . . . 7-12
Parts & Supplies . . . . . . . . . . . . . 16
Maintenance & Care . . . . . . 12-14
www.BISSELL.com
3
Getting to Know Your Deep Cleaner
9
1
10
2
3
15
4
11
16
5
6
17
7
18
12
8
13
1 Upper Handle
2 Easy Fill/Formula Cap
3Clean Water Tank
(3.7 Litre Capacity)
4 Power Button
5 Float Stack
6 Dirty Water Tank
7Belt Access Door
8Foot
9 Spray Trigger
10 In-Use Cord Clip
4
www.BISSELL.com
14
11 Cleaning Mode Switch
12 Accessory Hose Door
13 Belt/Brush Access Plate
14EdgeSweep™ Brushes
15 Carry Handle
16Rubber Tab
(on Dirty Water Tank)
17Quick Release for
Wrapped Cord
18 Recline Pedal
Assembly
WARNING
Do not plug in your deep cleaner until you are familiar with all instructions
and operating procedures.
Your deep cleaner
comes in four
easy-to-assemble
components and
an accessory bag.
• Base
• Upper Handle
• Clean Water Tank
• Carry Handle
1
First, insert
the upper
handle at the
top of the
base until you
hear a “click”.
In step 3, you will need to use a Phillips
screwdriver.
2
click
Side
View
Next, align the carry handle with the slots
on either side of the base (behind the
power switch and cleaning mode switch).
The carry handle will “click” into place.
Important: Do NOT put the clean tank on the machine until step 4.
3
4
5
Side
View
Using a Phillips screwdriver,
secure the carry handle with
the screw that’s taped to the
upper handle.
Wrap the cord around
the carry handle and quick
release hook.
At the bottom of the
upper handle, align the
clean water tank with
the grooves and slide
the tank into place.
www.BISSELL.com
5
Cleaning Formulas
WARNING
To reduce the risk of fire and electric shock due to internal component damage, use only
BISSELL cleaning fluids intended for use with the deep cleaner.
Keep plenty of genuine BISSELL formula
on hand so you can clean whenever it fits
your schedule.
Always use genuine BISSELL deep
cleaning formulas. Non-BISSELL cleaning
formulas may harm the machine and will
void the gaurantee.
PRETREAT
PRE TREAT SPOTS AND STAINS
TO IMPROVE CARPET CLEANING
PERFORMANCE
Stain PreTreat
Pet Stain PreTreat
Pretreat to
penetrate
and loosen
tough stains
Pretreat to help
remove tough
pet stains
and odors
2X* CONCENTRATED CLEANING FORMULAS
WASH &
REMOVE
WASH &
REMOVE
WASH & PROTECT
+
Antibacterial
Professional
Stain & Odour
Pet Stain &
Odour
Stain & Odour
+ Oxy
Cleans and
kills odour
causing
bacteria
Professional
strength to
remove extra
tough stains
and odours
Includes
Scotchgard™
Protector
Removes tough
pet stains
and contains
patented
odour removal
technology
Includes
Scotchgard™
Protector
Removes
tough stains
and odours
Includes
Scotchgard™
Protector
Permanently
removes
tough stains
like red wine,
coffee, tea,
cola and grape
juice with
Active Oxygen
Technology
WASH & REFRESH
Febreze™
Febreze™
Blossom & Cotton
Fresh
Breeze
Powerful
cleaning
with a
refreshing
spring scent
Powerful
cleaning
with a
refreshing
clean scen
Natural
Orange
Powerful
cleaning
with a
refreshing
natural
orange
scent
ONLY BISSELL Wash & Protect formulas protect from future stains with Scotchgard™ Protector.
Scotchgard™ is a trademark of 3M®.
*60 mL of 2X concentrated formula is equivalent to 120 mL of non-concentrated formula.
Tips Before Carpet Cleaning
• If cleaning an entire room, consider moving your furniture to another area.
• Use a dry vacuum cleaner over area before using your deep cleaner.
• Pre-treat stains with BISSELL PreTreat to improve performance on tough
stains and ground-in dirt.
6
www.BISSELL.com
Filling Your Clean Water Tank:
formula
If you’re not using a formula with a yellow EasyFill cap, please refer to
filling instructions on page 8.
1
2
Clean Water Tank
(3.7 Litre)
Dirty Water Tank
The clean water tank is at the
top of the machine.
3
Unscrew the cap from
the clean water tank.
Add hot tap water to
the water fill line. Twist
cap back into place.
4
Firmly insert the formula
bottle into the colour coded
cap on the clean water tank.
Simply squeeze until
formula reaches the
EasyFill line.
Lift the clean water tank
straight up to remove from
the machine.
5
At the bottom of the upper
handle, align the clean water
tank with the grooves and
slide the tank into place.
A few notes about filling the clean water tank:
• Fill with hot (140°F/60°C MAX) tap water and add the appropriate
BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER
OR TANK IN MICROWAVE.
• When using BISSELL Wash & Remove + Antibacterial formula: Only fill your
clean water tank with the recommended amount of water and formula to
achieve anti-bacterial benefits.
ATTENTION
Do not over wet carpet. Be careful not to run over loose objects or edges of area rugs.
Stalling the brush may result in premature belt failure.
www.BISSELL.com
7
Filling Your Clean Water Tank:
2X Concentrated Formula
1
2
Clean Water Tank
(3.7 Litre)
Dirty Water Tank
The clean water tank is at the
top of the machine.
3
Lift the clean water tank
straight up to remove from
the machine.
4
Unscrew the cap from the clean water tank. Add hot
tap water to the water fill line. Next, reference the chart
below for formula amounts to add to the tank. Twist
cap back into place.
FORMULA FILLING
INSTRUCTIONS
BISSELL 2X
Concentrated Formulas
DEEP CLEAN MODE
Fill water to the Water
Fill Line, then add 74 mL
of formula.
At the bottom of the upper
handle, align the clean water
tank with the grooves and
slide the tank into place.
EXPRESS CLEAN MODE
Fill water to the Water
Fill Line, then add 37 mL
of formula.
NOTE: Fill with hot (140°F/60°C MAX) tap water and add the appropriate
BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR
TANK IN MICROWAVE. Do not substitute BISSELL 2X Formula cleaning solution
with other household cleaning products.
8
www.BISSELL.com
Cleaning Your Carpet
1
2
3
Select
cleaning
mode:
Deep Clean
Delivers a deep
clean to your
carpet.
Express Clean
Provides a lighter
clean with about
1 hour of dry time.
Plug into a properly
earthed outlet.
*Choose “Deep
Clean” mode and use BISSELL
Wash & Remove + Antibacterial to
deliver antibacterial benefits.
Press the power button
to turn the machine on.
To recline your machine
for use, press the recline
pedal with your foot.
4
Deep Clean Mode:
Deep Clean Mode:
Express Clean Mode:
1. Press the spray trigger
to apply solution while
making 2 slow wet passes 1 forward and 1 back.
When using BISSELL
Wash & Remove +
Antibacterial Formula
1. Press the spray trigger to
apply solution while making
2 wet passes - 1 forward
and 1 back.
2. Release the trigger.
3. Make 2 slow dry passes 1 forward and 1 back, to
suck up the dirty solution.
(Do not hold down the
trigger for this step.)
NOTE: For best cleaning
performance, clean with
your machine in Deep
Clean Mode.
1. Press the spray trigger
to apply solution while
making 3 slow wet passes
- 1 forward, 1 back, and 1
forward again.
2. Release the trigger.
3. Make 1 slow dry pass
back, to suck up the dirty
solution. (Do not hold down
the trigger for this step.)
2. Release the trigger.
3. Make 2 dry passes 1 forward, 1 back to suck
up the dirty solution.
(Do not hold down the
trigger for this step.)
NOTE: In Express Clean
Mode, the dirty tank
will not get as full as
when cleaning with Deep
Clean Mode.
ATTENTION: To prevent damage to Berber carpets, avoid repeated strokes in
the same area.
www.BISSELL.com
9
Cleaning Area Rugs
Important! Please check manufacturer’s tag before cleaning area rugs for any
specialised cleaning instructions. Not for use on silk or delicate area rugs.
1
Select Express
Clean Mode.
2
Test in a small
inconspicuous
area first for
colourfastness.
3
Important: Keep the foot of the
deep cleaner perpendicular to the
rug’s edge with each cleaning pass
to prevent damage.
Cleaning with Hose and Tool
*Ensure the machine is upright while using the hose and tool.
(The rotating brush rolls under the foot will continue to turn while the hose
and tool are in use, but they will lift off the ground.)
1
2
Turn the machine off
and unplug from the
earthed outlet. Lift
accessory hose door
on top of foot on the
front of the machine.
The door flips toward
the machine to open.
Insert the hose and snap into
place. Be sure the coloured
hose release clip is facing out,
away from machine.
Important: Prime the hose by holding at ground
level and pressing the spray trigger until solution
starts to dispense out of the spray tip. Then,
release the spray trigger and proceed to step 3.
3
Attach the tool to the
end of the hose. (Tools
may vary by model.)
Plug into a properly
earthed outlet and
press the power button
to turn machine on.
Press the spray trigger button to spray the soiled area,
then slowly move tool back and forth over the area.
4
Release the spray trigger to suck up the dirty solution.
Work in small sections until the area is clean.
When finished cleaning, suction up warm clean water
from a tap or bowl to rinse the inside of the hose and tool.
Detach the hose and tool and close the accessory hose
door. Let the hose and tool air dry before storing.
NOTE: If using a Deep Reach Tool (select models only), be sure the needles of the
tool are pressed down into the carpet so the spray gets into the carpet fibres.
NOTE: Regularly clean high-traffic area rugs in Express Clean mode to remove
the forgotten dirt.
10
www.BISSELL.com
Cleaning with the Bare Floor Tool
(select models only)
1
2
Turn off and unplug your machine.
Attach the bare floor tool to the
foot’s bottom by lining the tool
to the edge of the nozzle. Rotate
down until it clicks into place.
Follow filling instructions on page
8 using the Wash & Shine Hard
Floor Cleaner formula and switch
cleaning mode to Express Clean.
3
Plug into a properly
earthed outlet and turn
the machine on. Clean by
pressing the spray trigger
for 1 wet pass forward, 1
wet pass back, and then
release the spray trigger
and make 1 dry pass
forward, 1 dry pass back.
When finished,
unplug the machine
and remove the
bare floor tool by
rotating the tool up
to unhook from the
nozzle. Rinse and let
dry before storing.
WARNING
WARNING: To reduce the risk of fire and electric shock when cleaning a hard floor, the
BISSELL Bare Floor Tool must be used, and is only to be used with BISSELL Wash & Shine
Hard Floor Cleaner formula intended for use with this appliance.
Empty Dirty Water Tank
WARNING
To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from
electrical outlet before performing maintenance or troubleshooting.
1
To remove dirty water
tank, press down on the
coloured tank handle.
2
Tilt the tank slightly toward
you. Grab the handle and
tank with both hands.
3
Pull dirty water tank up
and away to remove.
(continue to step 4)
www.BISSELL.com
11
Empty Dirty Water Tank (continued)
4
Quick Empty:
Pull the rubber tab
(located at the corner
of the top of the tank)
and tilt to pour. When
closing the rubber tab,
make sure all edges are
sealed tight.
Clean the red filter
below the dirty
tank by wiping off
any remaining dirt
or debris.
5
6
Final Rinse & Clean:
Unscrew ring at bottom
of tank by turning
counterclockwise.
Gently remove the float
stack, rinse and clean.
Once clean, return float
stack into the tank by
lining up the arrows
to point at each other.
With the arrows aligned,
the float stack will lock
into place. Return the
ring and twist clockwise
to lock. Water may leak
if the ring is not fully
tightened.
Return Dirty Tank:
Angle the tank
and insert bottom
first. Then tilt the
tank toward the
machine and push
the top in until it
clicks into place.
Did You Know?
The Float Stack
is what prevents
your dirty
tank from
overflowing.
Maintenance: Cleaning Machine After Use
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.
1
First, fill the clean water
tank with warm tap water
and then empty it all to
rinse. Then fill again with
warm tap water and return
the tank to the machine.
Twist cap back on tightly.
12
www.BISSELL.com
To flush and rinse machine:
Turn the machine on and
press the spray trigger for
15 seconds while making
back and forth passes on a
section of carpet. Release
the spray trigger and suck
up the water.
See pages 11-12 to clean the
water that was just sucked
up from the dirty tank.
Empty the clean water tank
and let dry before storing.
Wipe your machine’s
exterior with a soft cloth.
Maintenance: Cleaning the Nozzle
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.
1
2
If pet hair or debris
become clogged in
the nozzle, it can
be cleaned out of
the nozzle with the
nozzle clean out tool.
Turn off and unplug
the machine from
the earthed outlet.
Remove the nozzle from the foot by
flipping the accessory hose door open,
then lifting the accessory hose door and
nozzle up and away from the foot.
4
3
Hold the nozzle and insert the nozzle clean
out tool into the thin slot on the bottom of
the nozzle that touches the floor. Move the
nozzle clean out tool up and down, back
and forth to clean.
Return the nozzle back
onto the foot of the
machine by lining up the
three hooks on the
nozzle to the bottom of
the foot. (see arrows for location)
Rotate the nozzle up and click into place.
Close the accessory hose door.
Maintenance: Cleaning the Brush Rolls
1
Turn off and unplug
the machine from the
earthed outlet.
2
Lay the machine down
on its back or side.
3
Use the comb to brush
out the debris or hair from
the brush rolls.
www.BISSELL.com
13
Maintenance: Replacing Belts & Brush Roll
What you will need: 1 Phillips screwdriver & 1 flathead screwdriver
1
Remove clean
water tank and
make sure the dirty
water tank is empty.
Press the recline
pedal and lay the
machine on its side.
Remove 3 screws
on the belt/brush
access plate using a
Philips screwdriver.
Remove the plate
to expose the belt.
3
Large Wheel Belt
Replacement
2
Remove the brush
cover by lifting it up,
then lift the small
belt to remove. The
brush rolls can be
gently removed and
replaced with new
brush rolls. (Skip to
step 7 for small belt
replacement.)
4
5
Make sure to press the recline pedal
and lay the machine on its back. Use
a flathead screwdriver to help lift the
belt access door and remove. If the
belt is not broken, skip to step 8.
If the belt is
broken, gently
remove it from
the machine.
To replace the
large belt, place it
over the red area
of the large pulley
near the front of
the machine.
7
6
Stretch the belt towards the back of the
machine with your thumb and transfer it
onto the metal axle. Snap the belt access
door back into place.
8
Replace and secure the
brush roll cover, making
sure brush rolls are
aligned.
NOTE: It is important
the brush rolls align on
both ends of the foot.
Brush Roll & Small
Belt Replacement
9
Replace smaller
toothed belt by
wrapping around
the small metal
toothed pulley,
and the gear at
the end of the
rear-most brush.
Return belt/brush
access plate to the
end of the brush rolls.
It will “click” in place
when screws align.
Use a screwdriver to
secure the plate with
the three screws.
NOTE: Force must be used to lift the belt access door. There is a small belt and end cap
on the other end of the brush rolls. That belt needs to wrap around the tooth end of the
brush rolls and the end cap needs to be secure before re-assembling the machine.
14
www.BISSELL.com
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.
Problem
Reduced
spray OR
no spray
Loss of
suction
power
Possible causes
Remedies
Clean water tank may be empty
Refill tank
Clean water tank may not be
seated completely
Turn power OFF. Remove and
reseat tank
Pump may have lost prime in
hose cleaning mode
Hold end of hose below water level
in tank to prime
Tanks may not be seated properly
Pick up both tanks and reseat them
so they fit properly on the unit
Dirty tank has picked up
maximum amount of dirty water
and has reached full line
Empty dirty tank
Clean water tank is empty
Check fluid levels in the clean water
tank. Refill the tank if it is empty
Rubber tab on dirty water tank is
not sealed tight
Check the rubber tab on the dirty
water tank and press firmly on all
edges to secure it tightly (see step
4 on page 12 for detail)
Accessory hose door may not be
closed tightly in place
Check the accessory hose door
and make sure it is closed tightly by
pushing down to lock into place.
Nozzle may be clogged from pet
hair or debris
Use the nozzle clean out tool
and follow steps on page 13 for
“Cleaning Nozzle”
Helpful Cleaning Tips
›› Clean on a day with low humidity to help
carpets dry faster.
While Cleaning
›› Turn on any available ceiling fans and
make sure the room is well ventilated to
help the airstream in your home.
›› Additional dry strokes will aid in faster
drying of carpet. The two exceptions are
when using Express Clean Mode or when
using DeepClean + Antibacterial formula.
With these exceptions, the directions need
to be followed exactly.
For more helpful tips
and videos, check out
BISSELL.com
After Cleaning
›› U
se a portable fan directed towards
the surface of the carpet and/or a
dehumidifier to aid in drying carpet.
›› A
djust your heat up a few degrees in the
winter and use your air conditioning for
dryer air in the summer.
›› O
n warm dry days, simply opening the
windows can be an eco-friendly option to
assist in drying carpet.
›› W
hen the carpet feels dry to the touch,
return furniture that was removed. To be
sure to avoid staining, place wax paper or
aluminum foil under the legs. Wait at least
another three hours before removing wax
paper or foil.
www.BISSELL.com
15
Guarantee
This Guarantee only applies outside of the USA and Canada. It is
provided by BISSELL International Trading Company BV (“BISSELL”).
This Guarantee is provided by BISSELL. It gives you specific rights.
It is offered as an additional benefit to your rights under law. You
also have other rights under law which may vary from country
to country. You can find out about your legal rights and remedies
by contacting your local consumer advice service. Nothing in this
Guarantee will replace or lessen any of your legal rights or remedies.
If you need additional instruction regarding this Guarantee or have
questions regarding what it may cover, please contact BISSELL
Consumer Care or contact your local distributor.
This Guarantee is given to the original purchaser of the product from
new and is not transferable. You must be able to evidence the date
of purchase in order to claim under this Guarantee.
Limited Six-Year Guarantee
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below,
BISSELL will for six years from the date of purchase by the
original purchaser repair or replace (with new or remanufactured
components or products), at BISSELL’s option, free of charge, any
defective or malfunctioning part or product.
BISSELL recommends that the original packaging and evidence
of the date of purchase be kept for the duration of the Guarantee
period in case the need arises within the period to claim on the
Guarantee. Keeping the original packaging will assist with any
necessary re-packaging and transportation but is not a
condition of the Guarantee.
If your product is replaced by BISSELL under this Guarantee, the new
item will benefit from the remainder of the term of this Guarantee
(calculated from the date of the original purchase). The period of
this Guarantee shall not be extended whether or not your product
is repaired or replaced.
Service
If your BISSELL product should
require service or to claim under
our Limited Six-Year Guarantee,
please contact us as follows:
Website or Email:
www.BISSELL.com
[email protected]
Call or write:
Telephone: 0344-888-6644
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough
Berkshire, SL1 4QT
United Kingdom
16
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE GUARANTEE
This Guarantee applies to products used for personal domestic use and
not commercial or hire purposes. Consumable components such as
filters, belts and mop pads, which must be replaced or serviced by the
user from time to time, are not covered by this Guarantee.
This Guarantee does not apply to any defect arising from fair wear
and tear. Damage or malfunction caused by the user or any third
party whether as a result of accident, negligence, abuse, neglect, or
any other use not in accordance with the User Guide is not covered
by this Guarantee.
An unauthorised repair (or attempted repair) will void this Guarantee
whether or not damage has been caused by that repair/attempt.
Removing or tampering with the Product Rating Label on the
product or rendering it illegible will void this Guarantee.
SAVE AS SET OUT BELOW BISSELL AND ITS DISTRIBUTORS ARE NOT
LIABLE FOR ANY LOSS OR DAMAGE THAT IS NOT FORESEEABLE
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT INCLUDING
WITHOUT LIMITATION LOSS OF PROFIT, LOSS OF BUSINESS, BUSINESS
INTERRUPTION, LOSS OF OPPORTUNITY, DISTRESS, INCONVENIENCE OR
DISAPPOINTMENT. SAVE AS SET OUT BELOW BISSELL’S LIABILITY WILL
NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
BISSELL DOES NOT EXCLUDE OR LIMIT IN ANY WAY ITS LIABILITY FOR
(A) DEATH OR PERSONAL INJURY CAUSED BY OUR NEGLIGENCE OR THE
NEGLIGENCE OF OUR EMPLOYEES, AGENTS OR SUBCONTRACTORS; (B)
FRAUD OR FRAUDULENT MISREPRESENTATION; (C) OR FOR ANY OTHER
MATTER WHICH CANNOT BE EXCLUDED OR LIMITED UNDER LAW.
Visit us online at:
BISSELL.com
When contacting BISSELL, have model
number of cleaner available.
Model Number: _______________________
Purchase Date: _______________________
NOTE: Please keep your original sales
receipt. It provides proof of purchase
date in the event of a warranty claim.
Spares are available for purchase.
To purchase visit www.4bissell.co.uk.
©2016 BISSELL Homecare, Inc.
Grand Rapids, Michigan USA
All rights reserved. Printed in China
Part Number 160-8817 Rev 01/16 RevA
Visit our website at: www.BISSELL.com
Scotchgard is a trademark of 3M
Febreze® is a trademark of The Proctor & Gamble Company,
Cincinnati, Ohio used under license by BISSELL Homecare, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement