Parameter Files for PG

Parameter Files for PG
Parameter Files for PG-FP5
Release Note
R20UT2561EJ1200
Rev.12.00
Apr 01, 2016
Thank you for purchasing Parameter Files for PG-FP5.
This document describes cautions on using Parameter Files for PG-FP5. Also see the user’s manual of the PG-FP5 for
cautions on using the PG-FP5.
See a following WEB site about PG-FP5.
http://www.renesas.com/pg_fp5
Chapter 1.
Package List............................................................................................................................................... 3
Chapter 2.
Correspondence version and notes of PG-FP5.......................................................................................... 5
2.1
PR5-R5F10D (RL78/D1A), PR5-R5F10B (RL78/F13), PR5-R5F10P (RL78/F14), PR5-R5F113 (RL78/F15),
PR5-R5F114 (RL78/F1A), PR5-R5F104 (RL78/G14), PR5-R5F11A (RL78/G1D), PR5-R5F10F (RL78/G1E),
PR5-R5F11B (RL78/G1F), PR5-R5F11E (RL78/G1G), PR5-R5F11F (RL78/G1H), PR5-R5F10M (RL78/I1B),
PR5-R5F117 (RL78/I1D), PR5-R5F11C (RL78/I1E), PR5-R5F110 (RL78/L1C) ............................................................. 5
2.2
PR5-R5F10Y (RL78/G10) ................................................................................................................................. 6
2.3
PR5-70F3482 (V850E/Sx3-H) ........................................................................................................................... 7
2.4
PR5-70F3537 (V850E2/Dx4, V850E2/Dx4-H) ................................................................................................... 8
2.5
PR5-70F4012 (V850E2/Fx4), PR5-70F3545 (V850E2/Fx4-M).......................................................................... 9
2.6
PR5-70F3592 (V850E2/Fx4-G) ....................................................................................................................... 10
2.7
PR5-70F3585 (V850E2/Fx4-L) ........................................................................................................................ 11
2.8
PR5-70F4155 (V850E2/Px4-L), PR5-70F4159 (V850E2/PG4-S).................................................................... 12
2.9
PR5-70F4018 (V850E2/Sx4-H) ....................................................................................................................... 13
2.10
PR5-R5F5110 (RX110), PR5-R5F5111 (RX111), PR5-R5F5113 (RX113), PR5-R5F5130 (RX130) .......... 14
2.11
PR5-R5F5210 (RX210), PR5-R5F5210A (RX21A)...................................................................................... 15
2.12
PR5-R5F5220 (RX220)................................................................................................................................ 16
2.13
PR5-R5F5230 (RX230), PR5-R5F5231 (RX231) ........................................................................................ 17
2.14
PR5-R5F523T (RX23T), PR5-R5F524T (RX24T) ........................................................................................ 18
2.15
PR5-R5F5610 (RX610)................................................................................................................................ 19
2.16
PR5-R5F5621 (RX621), PR5-R5F562N (RX62N) ....................................................................................... 20
2.17
PR5-R5F562G (RX62G), PR5-R5F562T (RX62T) ...................................................................................... 21
2.18
PR5-R5F5630 (RX630), PR5-R5F5631 (RX631), PR5-R5F563N (RX63N) ................................................ 22
2.19
PR5-R5F5634 (RX634)................................................................................................................................ 23
2.20
PR5-R5F563T (RX63T) ............................................................................................................................... 24
2.21
PR5-RH850F1X (RH850/F1L), PR5-RH850 (RH850) ................................................................................. 25
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 1 of 29
Parameter Files for PG-FP5
2.22
Release Note
PR5-R5F564M (RX64M), PR5-R5F571M (RX71M), PR5-RH850C1X (RH850/C1x), PR5-RH850D1X
(RH850/D1x), PR5-RH850E1X (RH850/E1x), PR5-RH850F1X (RH850/F1M, RH850/F1H), PR5-RH850P1X
(RH850/P1x) .................................................................................................................................................................. 26
2.23
PR5-R8C3X (R8C/3x), PR5-R8C5X (R8C/5x), PR5-R8CLX (R8C/Lx) ........................................................ 27
2.24
PR5-78F8039 (UPD78F8032) ..................................................................................................................... 28
2.25
PR5-SH72AX (SH72Ax) .............................................................................................................................. 29
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 2 of 29
Parameter Files for PG-FP5
Release Note
Chapter 1.
Package List
Information on the packages listed below is given. For other packages, refer to the release notes that accompany the
packages.
RL78 Family
Group
RL78/D1A
RL78/F13
RL78/F14
RL78/F15
RL78/F1A
RL78/G10
RL78/G14
RL78/G1D
RL78/G1E
RL78/G1F
RL78/G1G
RL78/G1H
RL78/I1B
RL78/I1D
RL78/I1E
RL78/L1C
Package name
PR5-R5F10D
PR5-R5F10B
PR5-R5F10P
PR5-R5F113
PR5-R5F114
PR5-R5F10Y
PR5-R5F104
PR5-R5F11A
PR5-R5F10F
PR5-R5F11B
PR5-R5F11E
PR5-R5F11F
PR5-R5F10M
PR5-R5F117
PR5-R5F11C
PR5-R5F110
Package version
V1.01
V1.01
V1.01
V1.00
V1.00
V1.01
V1.07
V1.00
V1.02
V1.00
V1.00
V1.00
V1.00
V1.00
V1.00
V1.01
Refer to:
2.1
2.1
2.1
2.1
2.1
2.2
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
2.1
V850 Family
Group
V850E/Sx3-H
V850E2/Dx4, V850E2/Dx4-H
V850E2/Fx4
V850E2/Fx4-G
V850E2/Fx4-L
V850E2/Fx4-M
V850E2/Px4-L
V850E2/PG4-S
V850E2/Sx4-H
Package name
PR5-70F3482
PR5-70F3537
PR5-70F4012
PR5-70F3592
PR5-70F3585
PR5-70F3545
PR5-70F4155
PR5-70F4159
PR5-70F4018
Package version
V1.04
V1.01
V1.06
V1.01
V1.01
V1.02
V1.01
V1.00
V1.02
Refer to:
2.3
2.4
2.5
2.6
2.7
2.5
2.8
2.8
2.9
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 3 of 29
Parameter Files for PG-FP5
Release Note
RX Family
Group
RX110
RX111
RX113
RX130
RX210
RX21A
RX220
RX230
RX231
RX23T
RX24T
RX610
RX621
RX62G
RX62N
RX62T
RX630
RX631
RX634
RX63N
RX63T
RX64M
RX71M
Package name
PR5-R5F5110
PR5-R5F5111
PR5-R5F5113
PR5-R5F5130
PR5-R5F5210
PR5-R5F521A
PR5-R5F5220
PR5-R5F5230
PR5-R5F5231
PR5-R5F523T
PR5-R5F524T
PR5-R5F5610
PR5-R5F5621
PR5-R5F562G
PR5-R5F562N
PR5-R5F562T
PR5-R5F5630
PR5-R5F5631
PR5-R5F5634
PR5-R5F563N
PR5-R5F563T
PR5-R5F564M
PR5-R5F571M
Package version
V1.00
V1.01
V1.00
V1.00
V1.03
V1.01
V1.01
V1.00
V1.01
V1.00
V1.00
V1.01
V1.01
V1.01
V1.01
V1.01
V1.01
V1.04
V1.00
V1.04
V1.01
V1.01
V1.00
Refer to:
2.10
2.10
2.10
2.10
2.11
2.11
2.12
2.13
2.13
2.14
2.14
2.15
2.16
2.17
2.16
2.17
2.18
2.18
2.19
2.18
2.20
2.22
2.22
RH850 Family
Group
RH850/C1x
RH850/D1x
RH850/E1x
RH850/F1H
RH850/F1L
RH850/F1M
RH850/P1x
RH850
Package name
PR5-RH850C1X
PR5-RH850D1X
PR5-RH850E1X
PR5-RH850F1X
PR5-RH850F1X
PR5-RH850F1X
PR5-RH850P1X
PR5-RH850
Package version
V1.00
V1.01
V1.01
V1.05
V1.05
V1.05
V1.02
V1.01
Refer to:
2.22
2.22
2.22
2.22
2.21
2.22
2.22
2.21
R8C Family
Group
R8C/3x
R8C/5x
R8C/Lx
Package name
PR5-R8C3X
PR5-R8C5X
PR5-R8CLX
Package version
V1.06
V1.02
V1.03
Refer to:
2.23
2.23
2.23
78K Family
Group
UPD78F8032
Package name
PR5-78F8039
Package version
V1.01
Refer to:
2.24
SuperH Family
Group
SH72Ax
Package name
PR5-SH72AX
Package version
V1.01
Refer to:
2.25
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 4 of 29
Parameter Files for PG-FP5
Chapter 2.
2.1
2.1.1
Release Note
Correspondence version and notes of PG-FP5
PR5-R5F10D (RL78/D1A), PR5-R5F10B (RL78/F13), PR5-R5F10P
(RL78/F14), PR5-R5F113 (RL78/F15), PR5-R5F114 (RL78/F1A),
PR5-R5F104 (RL78/G14), PR5-R5F11A (RL78/G1D), PR5-R5F10F
(RL78/G1E), PR5-R5F11B (RL78/G1F), PR5-R5F11E (RL78/G1G),
PR5-R5F11F (RL78/G1H), PR5-R5F10M (RL78/I1B), PR5-R5F117
(RL78/I1D), PR5-R5F11C (RL78/I1E), PR5-R5F110 (RL78/L1C)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.06 or later
Firmware for PG-FP5
V2.06 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
Single-line UART
UART-ch0
115200,250000,500000,1MBaud
Supply oscillator setup
On Target check box
Supply origin
Frequency
Can’t be changed
Internal oscillation circuit
Can’t be changed
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Multiply rate
Can’t be changed
Page 5 of 29
Parameter Files for PG-FP5
2.2
2.2.1
Release Note
PR5-R5F10Y (RL78/G10)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.10 or later
Firmware for PG-FP5
V2.10 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
Single-line UART
UART-ch0
115200Baud
Supply oscillator setup
On Target check box
Supply origin
Frequency
Can’t be changed
Internal oscillation circuit
Can’t be changed
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Multiply rate
Can’t be changed
Page 6 of 29
Parameter Files for PG-FP5
2.3
Release Note
PR5-70F3482 (V850E/Sx3-H)
2.3.1
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.01 or later
Firmware for PG-FP5
V2.01 or later
FPGA for PG-FP5
V2 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
UARTA0
UART-ch0
CSIB0
CSIB0+HS
CSIB3
CSIB3+HS
Supply oscillator setup
On Target check box
SIO-ch0 (70F3xxx_CSI0.pr5)
SIO-H/S (70F3xxx_CSI0.pr5)
SIO-ch0 (70F3xxx_CSI3.pr5)
SIO-H/S (70F3xxx_CSI3.pr5)
Check box is selected
Note1
Supply origin
External oscillation circuit
Speed
9600,19200,31250,38400,57600,76800,115200,
128000,153600,500000Baud
9.8kHz~5000kHz
9.8kHz~5000kHz
9.8kHz~5000kHz
9.8kHz~5000kHz
Frequency
Note2
3.0MHz≦ fx ≦6.0MHz
Note2
6.0MHz< fx ≦10.0MHz
Multiply rate
PLL mode 8.00
PLL mode 4.00
Note1) Please don’t use programmer clock.
Note2) Please refer to the user’s manual of a device for Operation Conditions.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 7 of 29
Parameter Files for PG-FP5
2.4
2.4.1
Release Note
PR5-70F3537 (V850E2/Dx4, V850E2/Dx4-H)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.05 or later
Firmware for PG-FP5
V2.05 or later
FPGA for PG-FP5
V2 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
FLUR0
UART-ch0
115200,250000,500000,1MBaud
FLCS0
9.8kHz~5000kHz
SIO-ch0
Supply oscillator setup
On Target check box
Supply origin
Frequency
Note
Check box is selected
External oscillation circuit
Note) Please refer to the user’s manual of a device for Operation Conditions.
Multiply rate
Note
b. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 8 of 29
Parameter Files for PG-FP5
2.5
2.5.1
Release Note
PR5-70F4012 (V850E2/Fx4), PR5-70F3545 (V850E2/Fx4-M)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.05 or later
Firmware for PG-FP5
V2.05 or later
FPGA for PG-FP5
V2 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
FLUR0
UART-ch0
115200,250000,500000,1MBaud
FLCS0
9.8kHz~5000kHz
SIO-ch0
Supply oscillator setup
On Target check box
Supply origin
Frequency
Note
fx =4.0MHz
Note
4.0MHz<fx≦5.0MHz
Note
5.0MHz<fx≦8.0MHz
Check box is selected
External oscillation circuit
Note
8.0MHz<fx≦16.0MHz
Note
16.0MHz<fx≦20.0MHz
Note) Please refer to the user’s manual of a device for Operation Conditions.
Multiply rate
PLL mode 20.00
PLL mode 16.00
PLL mode 10.00
PLL mode 5.00
PLL mode 4.00
b. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 9 of 29
Parameter Files for PG-FP5
2.6
2.6.1
Release Note
PR5-70F3592 (V850E2/Fx4-G)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.07 or later
Firmware for PG-FP5
V2.07 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
FLUR0
UART-ch0
115200,250000,500000,1MBaud
FLCS0
9.8kHz~5000kHz
SIO-ch0
Supply oscillator setup (UPD70F3592)
On Target check box
Supply origin
Frequency
Note
fx=4.0MHz
Note
4.0MHz<fx≦5.0MHz
Note
5.0MHz<fx≦8.0MHz
Check box is selected
External oscillation circuit
Note
8.0MHz<fx≦16.0MHz
Note
16.0MHz<fx≦20.0MHz
Supply oscillator setup (Except UPD70F3592)
On Target check box
Supply origin
Frequency
Note
fx=4.0MHz
Note
4.0MHz<fx≦5.0MHz
Note
5.0MHz<fx≦8.0MHz
Check box is selected
External oscillation circuit
Note
8.0MHz<fx≦16.0MHz
Note
16.0MHz<fx≦20.0MHz
Note) Please refer to the user’s manual of a device for Operation Conditions.
Multiply rate
PLL mode 20.00
PLL mode 16.00
PLL mode 10.00
PLL mode 5.00
PLL mode 4.00
Multiply rate
PLL mode 16.00
PLL mode 9.00
PLL mode 8.00
PLL mode 4.00
PLL mode 1.00
b. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 10 of 29
Parameter Files for PG-FP5
2.7
2.7.1
Release Note
PR5-70F3585 (V850E2/Fx4-L)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.07 or later
Firmware for PG-FP5
V2.07 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
FLUR0
UART-ch0
115200,250000,500000,1MBaud
FLCS0
9.8kHz~5000kHz
SIO-ch0
Supply oscillator setup (UPD70F3579, UPD70F3580, UPD70F3584, UPD70F3585)
On Target check box
Supply origin
Frequency
Note
fx=4.0MHz
Note
4.0MHz<fx≦5.0MHz
Note
5.0MHz<fx≦8.0MHz
Check box is selected
External oscillation circuit
Note
8.0MHz<fx≦16.0MHz
Note
16.0MHz<fx≦20.0MHz
Supply oscillator setup (Except UPD70F3579, UPD70F3580, UPD70F3584, UPD70F3585)
On Target check box
Supply origin
Frequency
Note
fx=4.0MHz
Note
4.0MHz<fx≦5.0MHz
Note
5.0MHz<fx≦8.0MHz
Check box is selected
External oscillation circuit
Note
8.0MHz<fx≦16.0MHz
Note
16.0MHz<fx≦20.0MHz
Note) Please refer to the user’s manual of a device for Operation Conditions.
Multiply rate
PLL mode 16.00
PLL mode 9.00
PLL mode 8.00
PLL mode 4.00
PLL mode 1.00
Multiply rate
PLL mode 12.00
PLL mode 9.00
PLL mode 5.00
PLL mode 2.00
PLL mode 1.00
b. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 11 of 29
Parameter Files for PG-FP5
2.8
2.8.1
Release Note
PR5-70F4155 (V850E2/Px4-L), PR5-70F4159 (V850E2/PG4-S)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.07 or later
Firmware for PG-FP5
V2.07 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
FLUR
UART-ch0
115200,250000,500000,1MBaud
FLCS
9.8kHz~5000kHz
SIO-ch0
Supply oscillator setup
On Target check box
Supply origin
Frequency
Multiply rate
Note
Note
Check box is selected
External oscillation circuit
Note) Depends on the operating conditions of the option byte settings. Please refer to the user's manual for the device.
b. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 12 of 29
Parameter Files for PG-FP5
2.9
2.9.1
Release Note
PR5-70F4018 (V850E2/Sx4-H)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.05 or later
Firmware for PG-FP5
V2.05 or later
FPGA for PG-FP5
V2 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
FLUR0
UART-ch0
115200,250000,500000,1MBaud
FLCS0
9.8kHz~5000kHz
SIO-ch0
Supply oscillator setup
On Target check box
Supply origin
Frequency
Note
fx =4.0MHz
Note
4.0MHz<fx≦5.0MHz
Note
5.0MHz<fx≦8.0MHz
Check box is selected
External oscillation circuit
Note
8.0MHz<fx≦16.0MHz
Note
16.0MHz<fx≦20.0MHz
Note) Please refer to the user’s manual of a device for Operation Conditions.
Multiply rate
PLL mode 40.00
PLL mode 32.00
PLL mode 20.00
PLL mode 10.00
PLL mode 8.00
b. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 13 of 29
Parameter Files for PG-FP5
2.10
PR5-R5F5110 (RX110), PR5-R5F5111
(RX113), PR5-R5F5130 (RX130)
2.10.1
Correspondence version and notes of PG-FP5
Release Note
(RX111),
PR5-R5F5113
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.11 or later
Firmware for PG-FP5
V2.11 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Frequency
Multiply rate
When using SCI1: fx=16.0MHz
PLL mode
High-speed
When using FINE: fx=8.0MHz (VCC<3.0V),
Can’t be changed
(CKM) 1.00
on-chip oscillator
(CKP) 1.00
32MHz (VCC≧3.0V)
Communication system setup
Communication port of Device
Port
Speed
SCI1
UART
By setting the frequency and Multiply rate, you can select the
FINE
communication speed can be selected.
Fine-D
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 14 of 29
Parameter Files for PG-FP5
2.11
2.11.1
Release Note
PR5-R5F5210 (RX210), PR5-R5F5210A (RX21A)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.11 or later
Firmware for PG-FP5
V2.11 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Can’t be changed
High-speed on-chip
oscillator
Communication system setup
Communication port of Device
SCI1
FINE
Port
UART
Fine-D
Frequency
fx=32.0MHz
Multiply rate
PLL mode
(CKM) 1.00
(CKP) 1.00
Speed
By setting the frequency and Multiply rate, you can select the
communication speed can be selected.
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
c. Use R5F5xxxxx_x_2.pr5 when writing to R5F52105B or R5F52106B products having 144 or more pins. Use
R5F5xxxxx_x.pr5 to write to microcontrollers having 100 or less pins.
d. For the Chip Version A of the RX210, FINE is not supported.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 15 of 29
Parameter Files for PG-FP5
2.12
2.12.1
Release Note
PR5-R5F5220 (RX220)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.11 or later
Firmware for PG-FP5
V2.11 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Frequency
Can’t be changed
High-speed on-chip
oscillator
Communication system setup
Communication port of Device
SCI1
FINE
Port
UART
Fine-D
fx=32.0MHz
Multiply rate
PLL mode
(CKM) 0.50 (VCC<3.0V), 1.00 (VCC≧3.0V)
(CKP) 0.50 (VCC<3.0V), 1.00 (VCC≧3.0V)
Speed
By setting the frequency and Multiply rate, you can select the
communication speed can be selected.
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 16 of 29
Parameter Files for PG-FP5
2.13
2.13.1
Release Note
PR5-R5F5230 (RX230), PR5-R5F5231 (RX231)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.11 or later
Firmware for PG-FP5
V2.11 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Frequency
Can’t be changed
High-speed on-chip
oscillator
Communication system setup
Communication port of Device
SCI1
Port
UART
FINE
Fine-D
fx=8.0MHz (VCC<3.0V),
32.0MHz (VCC≧3.0V)
Multiply rate
When using SCI1: PLL mode
(CKM) 2.00
(CKP) 2.00
When using FINE: PLL mode
(CKM) 1.00
(CKP) 1.00
Speed
By setting the frequency and Multiply rate, you can select the
communication speed can be selected.
When using SCI1 and fx=32.0MHz, 4.000Mbd not selected.
When using fx=8.0MHz, 1.000Mbd or more is not selected.
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 17 of 29
Parameter Files for PG-FP5
2.14
2.14.1
Release Note
PR5-R5F523T (RX23T), PR5-R5F524T (RX24T)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.11 or later
Firmware for PG-FP5
V2.11 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Frequency
Can’t be changed
High-speed on-chip
oscillator
Communication system setup
Communication port of Device
SCI1
Port
UART
FINE
Fine-D
fx=32.0MHz
Multiply rate
When using SCI1: PLL mode
(CKM) 2.00
(CKP) 2.00
When using FINE: PLL mode
(CKM) 1.00
(CKP) 1.00
Speed
By setting the frequency and Multiply rate, you can select the
communication speed can be selected.
When using SCI1, 4.000Mbd not selected.
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 18 of 29
Parameter Files for PG-FP5
2.15
2.15.1
Release Note
PR5-R5F5610 (RX610)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.06 or later
Firmware for PG-FP5
V2.06 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 8.0MHz≦fx≦14.0MHz
(CKM) 1.00,2.00,4.00,8.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=8MHz~100MHz(ICLK)” and “Frequency * CKP=8MHz~50MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Communication system setup
Communication port of Device
Port
Speed
By setting the frequency and Multiply rate, you can select the
SCI4
UART
communication speed can be selected.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Frequency
Page 19 of 29
Parameter Files for PG-FP5
2.16
2.16.1
Release Note
PR5-R5F5621 (RX621), PR5-R5F562N (RX62N)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.06 or later
Firmware for PG-FP5
V2.06 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 8.0MHz≦fx≦14.0MHz
(CKM) 1.00,2.00,4.00,8.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=8MHz~100MHz(ICLK)” and “Frequency * CKP=8MHz~50MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Communication system setup
Communication port of Device
Port
Speed
By setting the frequency and Multiply rate, you can select the
SCI1
UART
communication speed can be selected.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Frequency
Page 20 of 29
Parameter Files for PG-FP5
2.17
2.17.1
Release Note
PR5-R5F562G (RX62G), PR5-R5F562T (RX62T)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.06 or later
Firmware for PG-FP5
V2.06 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 8.0MHz≦fx≦12.5MHz
(CKM) 1.00,2.00,4.00,8.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=8MHz~100MHz(ICLK)” and “Frequency * CKP=8MHz~50MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Communication system setup
Communication port of Device
Port
Speed
By setting the frequency and Multiply rate, you can select the
SCI1
UART
communication speed can be selected.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Frequency
Page 21 of 29
Parameter Files for PG-FP5
2.18
2.18.1
PR5-R5F5630
(RX63N)
(RX630),
Release Note
PR5-R5F5631
(RX631),
PR5-R5F563N
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.09 or later
Firmware for PG-FP5
V2.09 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup (R5F56316, R5F56317, R5F56318, R5F5631F, R5F5631G, R5F5631J, R5F5631W,
R5F5631Y, R5F563NF, R5F563NG, R5F563NJ, R5F563NW, R5F563NY)
On Target check box
Supply origin
Frequency
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 4.0MHz≦fx≦16.0MHz
(CKM) 1.00,2.00,4.00,8.00, 16.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=4MHz~100MHz(ICLK)” and “Frequency * CKP=4MHz~50MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Supply oscillator setup (Except R5F56316, R5F56317, R5F56318, R5F5631F, R5F5631G, R5F5631J, R5F5631W,
R5F5631Y, R5F563NF, R5F563NG, R5F563NJ, R5F563NW, R5F563NY)
On Target check box
Supply origin
Frequency
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 4.0MHz≦fx≦16.0MHz
(CKM) 1.00,2.00,4.00,8.00, 16.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=8MHz~100MHz(ICLK)” and “Frequency * CKP=8MHz~50MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Communication system setup
Communication port of Device
Port
Speed
By setting the frequency and Multiply rate, you can select the
SCI1
UART
communication speed can be selected.
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 22 of 29
Parameter Files for PG-FP5
2.19
2.19.1
Release Note
PR5-R5F5634 (RX634)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.09 or later
Firmware for PG-FP5
V2.09 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup
On Target check box
Supply origin
Frequency
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 4.0MHz≦fx≦20.0MHz
(CKM) 1.00,2.00,4.00,8.00, 16.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=4MHz~54MHz(ICLK)” and “Frequency * CKP=4MHz~32MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Communication system setup
Communication port of Device
Port
Speed
By setting the frequency and Multiply rate, you can select the
SCI1
UART
communication speed can be selected.
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 23 of 29
Parameter Files for PG-FP5
2.20
2.20.1
Release Note
PR5-R5F563T (RX63T)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.09 or later
Firmware for PG-FP5
V2.09 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup (R5F563TB, R5F563TC, R5F563TE)
On Target check box
Supply origin
Frequency
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 8.0MHz≦fx≦12.5MHz
(CKM) 1.00,2.00,4.00,8.00, 16.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=8MHz~100MHz(ICLK)” and “Frequency * CKP=8MHz~50MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Supply oscillator setup (Except R5F563TB, R5F563TC, R5F563TE)
On Target check box
Supply origin
Frequency
Multiply rate
Note
PLL mode
Note
Can’t be changed
External oscillation circuit 4.0MHz≦fx≦16.0MHz
(CKM) 1.00,2.00,4.00,8.00, 16.00
(CKP) 1.00,2.00,4.00,8.00
Note) Please set so that “Frequency * CKM=4MHz~100MHz(ICLK)” and “Frequency * CKP=4MHz~50MHz(PCLK)”.
Please refer to the user’s manual of a device for Operation Conditions.
Communication system setup
Communication port of Device
Port
Speed
By setting the frequency and Multiply rate, you can select the
SCI1
UART
communication speed can be selected.
b. If microcontroller is programmed by little endian, you must use the parameter file of R5F5xxxxx_L.pr5. The other
parameter file of R5F5xxxxx_B.pr5 is used by big endian.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 24 of 29
Parameter Files for PG-FP5
2.21
2.21.1
Release Note
PR5-RH850F1X (RH850/F1L), PR5-RH850 (RH850)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.12 or later
Firmware for PG-FP5
V2.12 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 25 of 29
Parameter Files for PG-FP5
2.22
2.22.1
Release Note
PR5-R5F564M (RX64M), PR5-R5F571M (RX71M), PR5-RH850C1X
(RH850/C1x),
PR5-RH850D1X
(RH850/D1x),
PR5-RH850E1X
(RH850/E1x),
PR5-RH850F1X
(RH850/F1M,
RH850/F1H),
PR5-RH850P1X (RH850/P1x)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.13 or later
Firmware for PG-FP5
V2.13 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. It is not possible to write it by supplying power from the flash programmer. Please supply power from the outside.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 26 of 29
Parameter Files for PG-FP5
2.23
2.23.1
Release Note
PR5-R8C3X (R8C/3x), PR5-R8C5X (R8C/5x), PR5-R8CLX (R8C/Lx)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.09 or later
Firmware for PG-FP5
V2.09 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
Standard serial I/O mode 3
UART I/O mode3
9600,19200,38400,57600,115200,250000,500000Baud
Supply oscillator setup
On Target check box
Supply origin
Frequency
Multiply rate
Can’t be changed
Internal oscillation circuit
Can’t be changed
Can’t be changed
b. For the R8C/Lx, if microcontroller is programmed by 2.7V≦VCC≦5.5V, you must use the parameter file of
R5F2LAxxx.pr5. The other parameter file of R5F2LAxxx_LV.pr5 is used by 1.8V≦VCC<2.7V.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 27 of 29
Parameter Files for PG-FP5
2.24
2.24.1
Release Note
PR5-78F8039 (UPD78F8032)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V1.00 or later
Firmware for PG-FP5
V1.00 or later
FPGA for PG-FP5
V1 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Communication system setup
Communication port of Device
Port
Speed
CSI10 (Internal oscillation circuit)
9.8kHz~2500kHz
CSI-Internal-OSC
UART6 (External clock/Programmer clock)
UART-EXCLK
115200Baud
UART6 (External oscillation circuit)
UART-X1-OSC
115200Baud
Supply oscillator setup
Note1
On Target check box
Supply origin
Frequency
Multiply rate
Internal oscillation circuit
Can’t be changed
Check box is selected
External clock/External
Can’t be changed
Note2
oscillation circuit
2.0MHz≦fx≦20.0MHz
Check box isn't selected
Programmer clock
Note1) Supply origin is changed by communication port of Device.
Note2) Please refer to the user’s manual of a device for Operation Conditions.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 28 of 29
Parameter Files for PG-FP5
2.25
2.25.1
Release Note
PR5-SH72AX (SH72Ax)
Correspondence version and notes of PG-FP5
1. Correspondence version
The correspondence of the version of this parameter file and PG-FP5 is as follows. Please use it in this combination.
Correspondence PG-FP5 version list
PG-FP5
Version
Programming GUI for PG-FP5
V2.11 or later
Firmware for PG-FP5
V2.11 or later
FPGA for PG-FP5
V4 or later
<Version confirmation>
• Programming GUI: Displayed by selecting [About FP5…] from the [Help] menu
• Firmware:
Displayed by selecting [Reset] from the [Programmer] menu
• FPGA:
Displayed by selecting [Reset] from the [Programmer] menu
2. Notes
a. Please set up programming GUI for PG-FP5 as follows.
Supply oscillator setup (SH72AW, SH72AY)
On Target check box
Supply origin
Can’t be changed
External oscillation circuit
Supply oscillator setup (SH72A0)
On Target check box
Supply origin
Can’t be changed
External oscillation circuit
SCI1
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Port
UART
fx=8.0MHz, 10.0MHz
Frequency
External oscillation circuit
Communication system setup
Communication port of Device
fx=20.0MHz
Frequency
Supply oscillator setup (SH72A2)
On Target check box
Supply origin
Can’t be changed
Frequency
fx=8.0MHz, 10.0MHz
Multiply rate
PLL mode
(CKM) 4.00
(CKP) 2.00
Multiply rate
PLL mode
(CKM) 8.00
(CKP) 4.00
Multiply rate
PLL mode
(CKM) 10.00
(CKP) 5.00
Speed
By setting the frequency and Multiply rate, you can select the
communication speed can be selected.
Page 29 of 29
Parameter Files for PG-FP5
Release Note
All trademarks and registered trademarks are the property of their respective owners.
R20UT2561EJ1200 Rev.12.00
Apr 01, 2016
Page 30 of 29
Notice
1.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use
of these circuits, software, or information.
2.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
3.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
4.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or
third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product.
5.
Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on
the product's quality grade, as indicated below.
"Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic
equipment; and industrial robots etc.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc.
Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical
implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it
in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses
incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics.
6.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
7.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or systems manufactured by you.
8.
Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9.
Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or
regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the
development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the
contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics
products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1)
"Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2)
"Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2801 Scott Boulevard Santa Clara, CA 95050-2549, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
9251 Yonge Street, Suite 8309 Richmond Hill, Ontario Canada L4C 9T3
Tel: +1-905-237-2004
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-585-100, Fax: +44-1628-585-900
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-6503-0, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
Room 1709, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100191, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 301, Tower A, Central Towers, 555 Langao Road, Putuo District, Shanghai, P. R. China 200333
Tel: +86-21-2226-0888, Fax: +86-21-2226-0999
Renesas Electronics Hong Kong Limited
Unit 1601-1611, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2265-6688, Fax: +852 2886-9022
Renesas Electronics Taiwan Co., Ltd.
13F, No. 363, Fu Shing North Road, Taipei 10543, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre, Singapore 339949
Tel: +65-6213-0200, Fax: +65-6213-0300
Renesas Electronics Malaysia Sdn.Bhd.
Unit 1207, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics India Pvt. Ltd.
No.777C, 100 Feet Road, HALII Stage, Indiranagar, Bangalore, India
Tel: +91-80-67208700, Fax: +91-80-67208777
Renesas Electronics Korea Co., Ltd.
12F., 234 Teheran-ro, Gangnam-Gu, Seoul, 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2016 Renesas Electronics Corporation. All rights reserved.
Colophon 5.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement