187 3 en~v~Specification Sheet

187 3 en~v~Specification Sheet
HEAT RECOVERY VENTILATOR
HRV SOLO 2.0ES
Part no. 47720
82 to 192 CFM (0.4 in. w.g.)
Controls
• This unit is very simple to operate. Once it is installed, press on its
push button, located on the bottom of the unit, to activate it. Press
once for low speed, once again for high speed, and once more to
stop it.
• For more convenience, this unit can also be controlled by an optional
main control. For a complete list of optional main and auxiliary
controls available, refer to the Wall Control Compatibility Chart
on last pages of wall controls specification sheet, available at
www.venmar.ca.
• For more details about controls, refer to the Main and auxiliary wall
controls user guide, also available at www.venmar.ca.
VB0165
SOLO®: THE ONE HRV YOU NEED FOR
OPTIMAL INDOOR AIR QUALITY
Homeowners who want the best in heat-recovery ventilation choose
the Solo 2.0ES for its power, reliability and very quiet operation. When
used along with the Altitude IAQ wall control with SMART mode
(automated ventilation based on indoor relative humidity and outdoor
temperature), the Solo 2.0ES allows you to optimize your ventilation
and your energy consumption. The Solo 2.0ES represents over 15 years
of continuous improvement to deliver contractors the durability and
reliability they have come to expect from Venmar.
Options
• Complete line of registers and diffusers
Defrosting System
The HRV Solo 2.0ES uses an efficient defrosting method. No negative
pressure is created by air exhausted to the outdoors, as the air is
recirculated into the house, helping to prevent any backdraft.
OUTDOOR TEMPERATURE
DEFROST CYCLE (MINUTES)
°C
°F
DEFROST / OPERATION
WARMER THAN -5
WARMER THAN 23
NO DEFROST
• Maintenance free, totally enclosed, sealed bearings motor; prevents
dust from entering
• Pressure taps, balancing dampers and straps for insulated ducts for
quick, effective installation
• Integrated “snap-in” drain system installs in seconds
with no additional parts
• Reversible for greater installation flexibility
• Recirculation mode, available with Altitude or Deco-touch main
control, to move air in homes without forced-air heating
• Very quiet operation
• ENERGY STAR® qualified
• Approved for the Novoclimat®* program for new homes when used
with Altitude or Deco-touch main wall control
Heat Recovery Core
*Novoclimat® is a program of the Agence de l’efficacité énergétique du Québec.
Dimensions: 12” x 14” x 15.5” (30.5 cm x 35.5 cm x 39.4 cm)
REPAIRS AND MAINTENANCE
Exchange surface: 102 ft² (9.54 m²)
All parts of the HRV SOLO 2.0ES can be removed in less than five minutes,
allowing direct access for easy repairs. The low power consumption
motor is permanently lubricated. Finally, the electronic circuit board
eliminates electromechanical parts, reducing repair time to a minimum.
Weight: 6.2 lb. (2.8 kg)
WARRANTY
The HRV Solo 2.0ES is protected by a 5-year warranty on parts. The heat
recovery core is covered by a lifetime warranty, with the original proof
of purchase.
Available at:
-5 TO -15
23 TO 5
6 / 50
-15 TO -27
5 TO -17
6 / 25
-27 AND LESS
-17 AND LESS
10 / 20
STALE AIR
FROM BUILDING
FILTRERED AIR
TO BUILDING
VF0053
Material: Polypropylene
Type: Crossflow core
Warranty: Limited Lifetime
Requirements and Standards
• Complies with the UL 1812 requirements regulating the installation
of Heat Recovery Ventilators
• Complies with the CSA C22.2 no. 113 Standard applicable to ventilators
• Complies with CSA F326 requirements regulating the installation of
Heat Recovery Ventilators
• Technical data was obtained from published results of tests relating
to CSA C439 Standards
• HVI certified and ENERGY STAR® qualified
DIMENSIONS: HRV SOLO 2.0ES
35” (891 mm)
Hooks Location
for Hanging Chains
17¼” (438 mm)
30¼” (768 mm)
Motorized
Damper
Terminal
Block
Location
17”
(432 mm)
Heat
Recovery
Core
Door
Power Cord
36” (914 mm)
VK0077A
VENTILATION PERFORMANCE
EXTERNAL STATIC
NET SUPPLY
PRESSURE
AIR FLOW
PA
IN. W.G.
L/S
CFM
M3/H
L/S
25
0.1
106 225 382 107
50
0.2
102 215 365 102
75
0.3
96 204 347 97
100
0.4
90 192 326 91
125
0.5
83 177 301 84
150
0.6
76 161 274 76
175
0.7
67 142 241 67
ENERGY PERFORMANCE
GROSS AIR FLOW
SUPPLY
EXHAUST
CFM
M3/H
L/S
CFM
227
386 118 249
216
367 115 243
205
348 111 235
193
328 107 226
179
304 100 211
162
275 89
189
143
243 75
159
SUPPLY
POWER
SENSIBLE APPARENT
NET AIR FLOW
TEMPERATURE
CONSUMED RECOVERY SENSIBLE
°C
°F L/S CFM M3/H WATTS EFFICIENCY EFFECTIVENESS
HEATING
0
32 39 82 139
71
65
75
0
32 61 130 221
129
60
69
M3/H
423
413
399
384
358
321
270
-25
-13
40 84
143
114
60
LATENT RECOVERY
MOISTURE
TRANSFER
76
0.01
0.01
0.03
100
APPARENT (%)
90
NET (%)
0.8
EFFICIENCY
EXTERNAL STATIC PRESSURE
IN. W.G. (PA = N X 248.8)
6”
(152 mm)
Blower
Assembly
0.6
0.4
70
60
50
SUPPLY (L/S)
EXHAUST (L/S)
0.2
80
40
0
0
25
0
50
75
100
125
150
175
200
225
250
275
VG0091A
CFM (L/S = CFM X 0.4719) (M³/H = L/S X 3.6)
25
50
75
100
VG0092
AIR FLOW - L/S (0.47 L/S = 1 CFM
NOTE: All specifications are subject to change without notice.
SPECIFICATIONS AND RATINGS
• Model: HRV Solo 2.0ES
• 6" Round Ports
• Speed Control on unit: Low and High speeds.
• Part Number: 47720
• Housing: Pre-painted steel
Other modes available with optional
mainl wall controls.
• Total Assembled Weight (including
• Insulation: Expanded polystyrene
polypropylene core): 65 lb. (29.5 kg)
• Drains: 1/2" (1.2 cm) fittings with
- Heat Exchange Surface Area: 102 ft.² (9.54 m²)
• Mounting: Suspension by chains and springs
10 ft. (3 m) PVC drain hose
• Filters: 15 ppi washable reticulated foam
- Type: Crossflow
- Material: Polypropylene
• Supply & Exhaust Blower Motor: 1 PSC Motor
15.375" x 7.125" x 0.75"
- Protection type: Thermally protected
(39 cm x 18 cm x 1.9 cm)
- Insulation class: B
Project:
Location:
Part Number: 47720
Quantity:
Submitted by:
• Heat Recovery Core:
• Unit Electrical Characteristics:
120 volts, 60 Hz, 2.1 amps, 195 watts
REMARKS
Date:
Residential Products Group, 550 Lemire Blvd., Drummondville, Qc, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715
www.venmar.ca
HRVSolo2.0ESd151015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement